255871 |
25-Sep-2013 |
scottl |
Re-do r255853. Along with adding back the API/ABI changes from the original, this hides the contents of cam_compat.h from ktrace/kdump/truss, avoiding problems there. There are no user-servicable parts in there, so no need for those tools to be groping around in there.
Approved by: re
|
255853 |
24-Sep-2013 |
scottl |
Update the CAM API for FreeBSD 10:
- Remove the timeout_ch field. It's been deprecated since FreeBSD 7.0; MPSAFE drivers should be managing their own timeout storage. The remaining non-MPSAFE drivers have been modified to also manage their own storage, and should be considered for updating to MPSAFE (or removal) during the FreeBSD 10.x lifecycle.
- Add fields related to soft timeouts and quality of service, to be used in upcoming work.
- Add room for more flags in the CCB header and path_inq structures.
- Begin support for extended 64-bit LUNs.
- Bump the CAM version number to 0x18, but add compat shims. Tested with camcontrol and smartctl.
Reviewed by: nathanw, ken, kib Approved by: re Obtained from: Netflix
|
249468 |
14-Apr-2013 |
mav |
MFprojects/camlock r248982: Stop abusing xpt_periph in random plases that really have no periph related to CCB, for example, bus scanning. NULL value is fine in such cases and it is correctly logged in debug messages as "noperiph". If at some point we need some real XPT periphs (alike to pmpX now), quite likely they will be per-bus, and not a single global instance as xpt_periph now.
|
246713 |
12-Feb-2013 |
kib |
Reform the busdma API so that new types may be added without modifying every architecture's busdma_machdep.c. It is done by unifying the bus_dmamap_load_buffer() routines so that they may be called from MI code. The MD busdma is then given a chance to do any final processing in the complete() callback.
The cam changes unify the bus_dmamap_load* handling in cam drivers.
The arm and mips implementations are updated to track virtual addresses for sync(). Previously this was done in a type specific way. Now it is done in a generic way by recording the list of virtuals in the map.
Submitted by: jeff (sponsored by EMC/Isilon) Reviewed by: kan (previous version), scottl, mjacob (isp(4), no objections for target mode changes) Discussed with: ian (arm changes) Tested by: marius (sparc64), mips (jmallet), isci(4) on x86 (jharris), amd64 (Fabian Keil <freebsd-listen@fabiankeil.de>)
|
203108 |
28-Jan-2010 |
mav |
MFp4: Large set of CAM inprovements.
- Unify bus reset/probe sequence. Whenever bus attached at boot or later, CAM will automatically reset and scan it. It allows to remove duplicate code from many drivers. - Any bus, attached before CAM completed it's boot-time initialization, will equally join to the process, delaying boot if needed. - New kern.cam.boot_delay loader tunable should help controllers that are still unable to register their buses in time (such as slow USB/ PCCard/ CardBus devices), by adding one more event to wait on boot. - To allow synchronization between different CAM levels, concept of requests priorities was extended. Priorities now split between several "run levels". Device can be freezed at specified level, allowing higher priority requests to pass. For example, no payload requests allowed, until PMP driver enable port. ATA XPT negotiate transfer parameters, periph driver configure caching and so on. - Frozen requests are no more counted by request allocation scheduler. It fixes deadlocks, when frozen low priority payload requests occupying slots, required by higher levels to manage theit execution. - Two last changes were holding proper ATA reinitialization and error recovery implementation. Now it is done: SATA controllers and Port Multipliers now implement automatic hot-plug and should correctly recover from timeouts and bus resets. - Improve SCSI error recovery for devices on buses without automatic sense reporting, such as ATAPI or USB. For example, it allows CAM to wait, while CD drive loads disk, instead of immediately return error status. - Decapitalize diagnostic messages and make them more readable and sensible. - Teach PMP driver to limit maximum speed on fan-out ports. - Make boot wait for PMP scan completes, and make rescan more reliable. - Fix pass driver, to return CCB to user level in case of error. - Increase number of retries in cd driver, as device may return several UAs.
|
183397 |
27-Sep-2008 |
ed |
Replace all calls to minor() with dev2unit().
After I removed all the unit2minor()/minor2unit() calls from the kernel yesterday, I realised calling minor() everywhere is quite confusing. Character devices now only have the ability to store a unit number, not a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call minor(), while they should actually be calling dev2unit(). In -CURRENT this isn't a problem, but it turns out we never had any problem reports related to that issue in the past. I suspect not many people connect more than 256 pieces of the same hardware.
Reviewed by: kib
|