Searched refs:SER_RS485_RTS_AFTER_SEND (Results 1 - 19 of 19) sorted by relevance
| /linux-master/include/uapi/linux/ |
| H A D | serial.h | 135 * * %SER_RS485_RTS_AFTER_SEND - Logical level for RTS pin after sent.
147 #define SER_RS485_RTS_AFTER_SEND _BITUL(2) macro
|
| /linux-master/drivers/tty/serial/8250/ |
| H A D | 8250_fintek.c | 207 !(rs485->flags & SER_RS485_RTS_AFTER_SEND))
415 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND,
421 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND,
|
| H A D | 8250_dwlib.c | 238 SER_RS485_RTS_AFTER_SEND | SER_RS485_ADDRB | SER_RS485_ADDR_RECV |
|
| H A D | 8250_bcm2835aux.c | 69 if (up->port.rs485.flags & SER_RS485_RTS_AFTER_SEND)
|
| H A D | 8250_lpc18xx.c | 85 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND,
|
| H A D | 8250_port.c | 593 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
617 !!(rs485->flags & SER_RS485_RTS_AFTER_SEND)) {
619 rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
1399 if (p->port.rs485.flags & SER_RS485_RTS_AFTER_SEND)
|
| H A D | 8250_pci1xxxx.c | 147 SER_RS485_RTS_AFTER_SEND,
|
| /linux-master/drivers/tty/serial/ |
| H A D | omap-serial.c | 296 res = (port->rs485.flags & SER_RS485_RTS_AFTER_SEND) ?
1309 SER_RS485_RTS_AFTER_SEND : SER_RS485_RTS_ON_SEND;
1483 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
1512 rs485conf->flags &= ~SER_RS485_RTS_AFTER_SEND;
1515 rs485conf->flags |= SER_RS485_RTS_AFTER_SEND;
1519 gflags = rs485conf->flags & SER_RS485_RTS_AFTER_SEND ?
|
| H A D | ar933x_uart.c | 440 gpiod_set_value(up->rts_gpiod, !!(rs485conf->flags & SER_RS485_RTS_AFTER_SEND));
590 !!(rs485conf->flags & SER_RS485_RTS_AFTER_SEND));
698 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND,
|
| H A D | imx.c | 449 if (port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
1708 if (port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
1953 if (rs485conf->flags & SER_RS485_RTS_AFTER_SEND)
2229 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
|
| H A D | mcf.c | 439 .flags = SER_RS485_ENABLED | SER_RS485_RTS_AFTER_SEND,
|
| H A D | serial_core.c | 1314 SER_RS485_RTS_AFTER_SEND | SER_RS485_RX_DURING_TX | \
1396 !(rs485->flags & SER_RS485_RTS_AFTER_SEND)) {
1399 rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
1405 rs485->flags |= SER_RS485_RTS_AFTER_SEND;
3658 SER_RS485_RTS_AFTER_SEND);
3669 rs485conf->flags |= SER_RS485_RTS_AFTER_SEND;
|
| H A D | stm32-usart.c | 1377 rs485conf->flags &= ~SER_RS485_RTS_AFTER_SEND;
1380 rs485conf->flags |= SER_RS485_RTS_AFTER_SEND;
1571 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
|
| H A D | sc16is7xx.c | 875 if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
1461 .flags = SER_RS485_ENABLED | SER_RS485_RTS_AFTER_SEND,
|
| H A D | xilinx_uartps.c | 221 SER_RS485_RTS_AFTER_SEND,
367 enable = cdns_uart->port->rs485.flags & SER_RS485_RTS_AFTER_SEND;
|
| H A D | amba-pl011.c | 1302 if (port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
2772 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
|
| H A D | fsl_lpuart.c | 1475 else if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
1505 else if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
2789 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND,
|
| H A D | atmel_serial.c | 2533 .flags = SER_RS485_ENABLED | SER_RS485_RTS_AFTER_SEND | SER_RS485_RX_DURING_TX,
|
| /linux-master/drivers/usb/serial/ |
| H A D | xr_serial.c | 834 rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
836 rs485->flags |= SER_RS485_RTS_AFTER_SEND;
840 SER_RS485_RTS_AFTER_SEND;
|
Completed in 532 milliseconds