serial: 8250_dw: Do not bailout on UCV read returning zero

Designware UART has optional feature FIFO_MODE to implement FIFO.
Encoding FIFO capabilities through Component Parameter Register CPR is
optional and it can be enabled using parameter UART_ADD_ENCODED_PARAMS.

Driver can exercise fifo capabilities by decoding CPR if implemented
or from cpr_val provided from the dw8250_platform_data otherwise.

dw8250_setup_port() checks for CPR or cpr_val to determine FIFO size
only when Component Version (UCV) is non-zero. Bailing out early on UCV
read returning zero will leave fifosize as zero and !UART_CAP_FIFO,
hence prevent early return and continue to process CPR or cpr_val for
the driver to utilize FIFO.

Non-zero UCV implies ADDITIONAL_FEATURES=1, preventing early return
will not be an overhead here.

Signed-off-by: Vamshi Gajjela <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20231231182951.877805-1-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dw: Decouple DLF register check from UCV

Designware UART has an optional feature to enable Fractional Baud Rate
Divisor (DLF) through the FRACTIONAL_BAUD_DIVISOR_EN configuration
parameter, and it is not dependent on ADDITIONAL_FEATURES.

dw8250_setup_port() checks DLF to determine dlf_size only when UART
Component Version (UCV) is non-zero. As mentioned above DLF and UCV are
independent features. Move the logic corresponding to DLF size
calculation ahead of the UCV check to prevent early return. Otherwise,
dlf_size will be zero and driver will not be able to use the
controller's fractional baud rate divisor (DLF) feature.

Signed-off-by: Vamshi Gajjela <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20231126160420.2442330-1-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dw: Preserve original value of DLF register

Preserve the original value of the Divisor Latch Fraction (DLF) register.
When the DLF register is modified without preservation, it can disrupt
the baudrate settings established by firmware or bootloader, leading to
data corruption and the generation of unreadable or distorted characters.

Fixes: 701c5e73b296 ("serial: 8250_dw: add fractional divisor support")
Cc: stable <stable@kernel.org>
Signed-off-by: Ruihong Luo <colorsu1922@gmail.com>
Link: https://lore.kernel.org/stable/20230713004235.35904-1-colorsu1922%40gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230713004235.35904-1-colorsu1922@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: Make ->set_termios() old ktermios const

There should be no reason to adjust old ktermios which is going to get
discarded anyway.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dwlib: remove redundant sanity check for RS485 flags

Before the drivers rs485_config() function is called the serial core
already ensures that only one of both options RTS on send or RTS after send
is set. So remove the concerning sanity check in the driver function to
avoid redundancy.

Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-8-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: Embed rs485_supported to uart_port

Embed rs485_supported to uart_port to allow serial core to tweak it as
needed.

Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

8250_dwlib: Convert bitops to newer form

Instead of open-coding, use BIT(), GENMASK(), and FIELD_GET() helpers.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220630100536.41329-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dwlib: Support for 9th bit multipoint addressing

Add 9th bit multipoint addressing mode for DW UART. 9th bit addressing
can be used only when HW RS485 is available.

Updating RAR (receive address register) is bit tricky because busy
indication is not be available when DW UART is strictly 16550
compatible, which is the case with the hardware I was testing with. RAR
should not be updated while receive is in progress which is now
achieved by deasserting RE and waiting for one frame (in case rx would
be in progress, the driver seems to have no way of knowing it w/o busy
indication). Because of this complexity, it's better to avoid doing it
unless really needed.

Co-developed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Co-developed-by: Lakshmi Sowjanya <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Lakshmi Sowjanya <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: take termios_rwsem for ->rs485_config() & pass termios as param

To be able to alter ADDRB within ->rs485_config(), take termios_rwsem
before calling ->rs485_config() and pass termios.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dwlib: Remove serial_rs485 sanitization

Serial core handles serial_rs485 sanitization and rs485 struct
assignment. As serial_rs485 is already clear for the non-RS485 case by
serial core, there no need to clear flags in the driver.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-26-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dwlib: Fill in rs485_supported

Add information on supported serial_rs485 features. When the driver is
using em485, take advantage of serial8250_em485_supported.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dwlib: Implement SW half duplex support

This patch enables support for SW half-duplex mode using em485.

Cc: Eric Tremblay <etremblay@distech-controls.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220426122448.38997-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dwlib: RS485 HW half & full duplex support

The Synopsys DesignWare UART can be configured to have HW support for
the RS485 protocol from IP version 4.0 onward. Add support for
hardware-controlled half duplex and full duplex modes.

HW will take care of managing DE and RE, the driver just gives it
permission to use either by setting both to 1.

To ask for full duplex mode, userspace sets SER_RS485_RX_DURING_TX flag
and HW will take care of the rest.

Set delay_rts_before_send and delay_rts_after_send to zero for now. The
granularity of that ABI is too coarse to be useful.

Co-developed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220426122448.38997-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250: dw: Move the IO accessors to 8250_dwlib.h

These accessors should be used instead of the regular readl/writel()
helpers. In order to use them also from 8250_dw.c in this directory,
move the helpers to 8250_dwlib.h

There is no functional change.

There is no need for declaring `struct uart_port` or even UPIO_MEM32BE
which both are already included in the 8250_dwlib.h header by 8250.h.

Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-8-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250: dw: Allow to use a fallback CPR value if not synthesized

DW UART controllers can be synthesized without the CPR register.
In this case, allow to the platform information to provide a CPR value.

Co-developed-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-5-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_lpss: Extract dw8250_do_set_termios() for common use

Some of the code currently used in dw8250_set_termios(), byt_set_termios()
may be reused by other methods in the future. Extract it to a common helper
function.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005133026.21488-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dw: split Synopsys DesignWare 8250 common functions

We would like to use same functions in the couple of drivers for
Synopsys DesignWare 8250 UART. Split them from 8250_dw into new brand
library module which users will select explicitly.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>