Searched hist:164264 (Results 1 - 11 of 11) sorted by relevance
| /freebsd-9.3-release/sys/dev/pci/ | ||
| H A D | pci_if.m | diff 164264 Mon Nov 13 19:47:30 MST 2006 jhb First cut at MI support for PCI Message Signalled Interrupts (MSI): - Add 3 new functions to the pci_if interface along with suitable wrappers to provide the device driver visible API: - pci_alloc_msi(dev, int *count) backed by PCI_ALLOC_MSI(). '*count' here is an in and out parameter. The driver stores the desired number of messages in '*count' before calling the function. On success, '*count' holds the number of messages allocated to the device. Also on success, the driver can access the messages as SYS_RES_IRQ resources starting at rid 1. Note that the legacy INTx interrupt resource will not be available when using MSI. Note that this function will allocate either MSI or MSI-X messages depending on the devices capabilities and the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. Also note that the driver should activate the memory resource that holds the MSI-X table and pending bit array (PBA) before calling this function if the device supports MSI-X. - pci_release_msi(dev) backed by PCI_RELEASE_MSI(). This function releases the messages allocated for this device. All of the SYS_RES_IRQ resources need to be released for this function to succeed. - pci_msi_count(dev) backed by PCI_MSI_COUNT(). This function returns the maximum number of MSI or MSI-X messages supported by this device. MSI-X is preferred if present, but this function will honor the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. This function should return the largest value that pci_alloc_msi() can return (assuming the MD code is able to allocate sufficient backing resources for all of the messages). - Add default implementations for these 3 methods to the pci_driver generic PCI bus driver. (The various other PCI bus drivers such as for ACPI and OFW will inherit these default implementations.) This default implementation depends on 4 new pcib_if methods that bubble up through the PCI bridges to the MD code to allocate IRQ values and perform any needed MD setup code needed: - PCIB_ALLOC_MSI() attempts to allocate a group of MSI messages. - PCIB_RELEASE_MSI() releases a group of MSI messages. - PCIB_ALLOC_MSIX() attempts to allocate a single MSI-X message. - PCIB_RELEASE_MSIX() releases a single MSI-X message. - Add default implementations for these 4 methods that just pass the request up to the parent bus's parent bridge driver and use the default implementation in the various MI PCI bridge drivers. - Add MI functions for use by MD code when managing MSI and MSI-X interrupts: - pci_enable_msi(dev, address, data) programs the MSI capability address and data registers for a group of MSI messages - pci_enable_msix(dev, index, address, data) initializes a single MSI-X message in the MSI-X table - pci_mask_msix(dev, index) masks a single MSI-X message - pci_unmask_msix(dev, index) unmasks a single MSI-X message - pci_pending_msix(dev, index) returns true if the specified MSI-X message is currently pending - Save the MSI capability address and data registers in the pci_cfgreg block in a PCI devices ivars and restore the values when a device is resumed. Note that the MSI-X table is not currently restored during resume. - Add constants for MSI-X register offsets and fields. - Record interesting data about any MSI-X capability blocks we come across in the pci_cfgreg block in the ivars for PCI devices. Tested on: em (i386, MSI), bce (amd64/i386, MSI), mpt (amd64, MSI-X) Reviewed by: scottl, grehan, jfv MFC after: 2 months |
| H A D | pcib_if.m | diff 164264 Mon Nov 13 19:47:30 MST 2006 jhb First cut at MI support for PCI Message Signalled Interrupts (MSI): - Add 3 new functions to the pci_if interface along with suitable wrappers to provide the device driver visible API: - pci_alloc_msi(dev, int *count) backed by PCI_ALLOC_MSI(). '*count' here is an in and out parameter. The driver stores the desired number of messages in '*count' before calling the function. On success, '*count' holds the number of messages allocated to the device. Also on success, the driver can access the messages as SYS_RES_IRQ resources starting at rid 1. Note that the legacy INTx interrupt resource will not be available when using MSI. Note that this function will allocate either MSI or MSI-X messages depending on the devices capabilities and the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. Also note that the driver should activate the memory resource that holds the MSI-X table and pending bit array (PBA) before calling this function if the device supports MSI-X. - pci_release_msi(dev) backed by PCI_RELEASE_MSI(). This function releases the messages allocated for this device. All of the SYS_RES_IRQ resources need to be released for this function to succeed. - pci_msi_count(dev) backed by PCI_MSI_COUNT(). This function returns the maximum number of MSI or MSI-X messages supported by this device. MSI-X is preferred if present, but this function will honor the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. This function should return the largest value that pci_alloc_msi() can return (assuming the MD code is able to allocate sufficient backing resources for all of the messages). - Add default implementations for these 3 methods to the pci_driver generic PCI bus driver. (The various other PCI bus drivers such as for ACPI and OFW will inherit these default implementations.) This default implementation depends on 4 new pcib_if methods that bubble up through the PCI bridges to the MD code to allocate IRQ values and perform any needed MD setup code needed: - PCIB_ALLOC_MSI() attempts to allocate a group of MSI messages. - PCIB_RELEASE_MSI() releases a group of MSI messages. - PCIB_ALLOC_MSIX() attempts to allocate a single MSI-X message. - PCIB_RELEASE_MSIX() releases a single MSI-X message. - Add default implementations for these 4 methods that just pass the request up to the parent bus's parent bridge driver and use the default implementation in the various MI PCI bridge drivers. - Add MI functions for use by MD code when managing MSI and MSI-X interrupts: - pci_enable_msi(dev, address, data) programs the MSI capability address and data registers for a group of MSI messages - pci_enable_msix(dev, index, address, data) initializes a single MSI-X message in the MSI-X table - pci_mask_msix(dev, index) masks a single MSI-X message - pci_unmask_msix(dev, index) unmasks a single MSI-X message - pci_pending_msix(dev, index) returns true if the specified MSI-X message is currently pending - Save the MSI capability address and data registers in the pci_cfgreg block in a PCI devices ivars and restore the values when a device is resumed. Note that the MSI-X table is not currently restored during resume. - Add constants for MSI-X register offsets and fields. - Record interesting data about any MSI-X capability blocks we come across in the pci_cfgreg block in the ivars for PCI devices. Tested on: em (i386, MSI), bce (amd64/i386, MSI), mpt (amd64, MSI-X) Reviewed by: scottl, grehan, jfv MFC after: 2 months |
| H A D | pcib_private.h | diff 164264 Mon Nov 13 19:47:30 MST 2006 jhb First cut at MI support for PCI Message Signalled Interrupts (MSI): - Add 3 new functions to the pci_if interface along with suitable wrappers to provide the device driver visible API: - pci_alloc_msi(dev, int *count) backed by PCI_ALLOC_MSI(). '*count' here is an in and out parameter. The driver stores the desired number of messages in '*count' before calling the function. On success, '*count' holds the number of messages allocated to the device. Also on success, the driver can access the messages as SYS_RES_IRQ resources starting at rid 1. Note that the legacy INTx interrupt resource will not be available when using MSI. Note that this function will allocate either MSI or MSI-X messages depending on the devices capabilities and the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. Also note that the driver should activate the memory resource that holds the MSI-X table and pending bit array (PBA) before calling this function if the device supports MSI-X. - pci_release_msi(dev) backed by PCI_RELEASE_MSI(). This function releases the messages allocated for this device. All of the SYS_RES_IRQ resources need to be released for this function to succeed. - pci_msi_count(dev) backed by PCI_MSI_COUNT(). This function returns the maximum number of MSI or MSI-X messages supported by this device. MSI-X is preferred if present, but this function will honor the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. This function should return the largest value that pci_alloc_msi() can return (assuming the MD code is able to allocate sufficient backing resources for all of the messages). - Add default implementations for these 3 methods to the pci_driver generic PCI bus driver. (The various other PCI bus drivers such as for ACPI and OFW will inherit these default implementations.) This default implementation depends on 4 new pcib_if methods that bubble up through the PCI bridges to the MD code to allocate IRQ values and perform any needed MD setup code needed: - PCIB_ALLOC_MSI() attempts to allocate a group of MSI messages. - PCIB_RELEASE_MSI() releases a group of MSI messages. - PCIB_ALLOC_MSIX() attempts to allocate a single MSI-X message. - PCIB_RELEASE_MSIX() releases a single MSI-X message. - Add default implementations for these 4 methods that just pass the request up to the parent bus's parent bridge driver and use the default implementation in the various MI PCI bridge drivers. - Add MI functions for use by MD code when managing MSI and MSI-X interrupts: - pci_enable_msi(dev, address, data) programs the MSI capability address and data registers for a group of MSI messages - pci_enable_msix(dev, index, address, data) initializes a single MSI-X message in the MSI-X table - pci_mask_msix(dev, index) masks a single MSI-X message - pci_unmask_msix(dev, index) unmasks a single MSI-X message - pci_pending_msix(dev, index) returns true if the specified MSI-X message is currently pending - Save the MSI capability address and data registers in the pci_cfgreg block in a PCI devices ivars and restore the values when a device is resumed. Note that the MSI-X table is not currently restored during resume. - Add constants for MSI-X register offsets and fields. - Record interesting data about any MSI-X capability blocks we come across in the pci_cfgreg block in the ivars for PCI devices. Tested on: em (i386, MSI), bce (amd64/i386, MSI), mpt (amd64, MSI-X) Reviewed by: scottl, grehan, jfv MFC after: 2 months |
| H A D | pci_private.h | diff 164264 Mon Nov 13 19:47:30 MST 2006 jhb First cut at MI support for PCI Message Signalled Interrupts (MSI): - Add 3 new functions to the pci_if interface along with suitable wrappers to provide the device driver visible API: - pci_alloc_msi(dev, int *count) backed by PCI_ALLOC_MSI(). '*count' here is an in and out parameter. The driver stores the desired number of messages in '*count' before calling the function. On success, '*count' holds the number of messages allocated to the device. Also on success, the driver can access the messages as SYS_RES_IRQ resources starting at rid 1. Note that the legacy INTx interrupt resource will not be available when using MSI. Note that this function will allocate either MSI or MSI-X messages depending on the devices capabilities and the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. Also note that the driver should activate the memory resource that holds the MSI-X table and pending bit array (PBA) before calling this function if the device supports MSI-X. - pci_release_msi(dev) backed by PCI_RELEASE_MSI(). This function releases the messages allocated for this device. All of the SYS_RES_IRQ resources need to be released for this function to succeed. - pci_msi_count(dev) backed by PCI_MSI_COUNT(). This function returns the maximum number of MSI or MSI-X messages supported by this device. MSI-X is preferred if present, but this function will honor the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. This function should return the largest value that pci_alloc_msi() can return (assuming the MD code is able to allocate sufficient backing resources for all of the messages). - Add default implementations for these 3 methods to the pci_driver generic PCI bus driver. (The various other PCI bus drivers such as for ACPI and OFW will inherit these default implementations.) This default implementation depends on 4 new pcib_if methods that bubble up through the PCI bridges to the MD code to allocate IRQ values and perform any needed MD setup code needed: - PCIB_ALLOC_MSI() attempts to allocate a group of MSI messages. - PCIB_RELEASE_MSI() releases a group of MSI messages. - PCIB_ALLOC_MSIX() attempts to allocate a single MSI-X message. - PCIB_RELEASE_MSIX() releases a single MSI-X message. - Add default implementations for these 4 methods that just pass the request up to the parent bus's parent bridge driver and use the default implementation in the various MI PCI bridge drivers. - Add MI functions for use by MD code when managing MSI and MSI-X interrupts: - pci_enable_msi(dev, address, data) programs the MSI capability address and data registers for a group of MSI messages - pci_enable_msix(dev, index, address, data) initializes a single MSI-X message in the MSI-X table - pci_mask_msix(dev, index) masks a single MSI-X message - pci_unmask_msix(dev, index) unmasks a single MSI-X message - pci_pending_msix(dev, index) returns true if the specified MSI-X message is currently pending - Save the MSI capability address and data registers in the pci_cfgreg block in a PCI devices ivars and restore the values when a device is resumed. Note that the MSI-X table is not currently restored during resume. - Add constants for MSI-X register offsets and fields. - Record interesting data about any MSI-X capability blocks we come across in the pci_cfgreg block in the ivars for PCI devices. Tested on: em (i386, MSI), bce (amd64/i386, MSI), mpt (amd64, MSI-X) Reviewed by: scottl, grehan, jfv MFC after: 2 months |
| H A D | pcireg.h | diff 164264 Mon Nov 13 19:47:30 MST 2006 jhb First cut at MI support for PCI Message Signalled Interrupts (MSI): - Add 3 new functions to the pci_if interface along with suitable wrappers to provide the device driver visible API: - pci_alloc_msi(dev, int *count) backed by PCI_ALLOC_MSI(). '*count' here is an in and out parameter. The driver stores the desired number of messages in '*count' before calling the function. On success, '*count' holds the number of messages allocated to the device. Also on success, the driver can access the messages as SYS_RES_IRQ resources starting at rid 1. Note that the legacy INTx interrupt resource will not be available when using MSI. Note that this function will allocate either MSI or MSI-X messages depending on the devices capabilities and the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. Also note that the driver should activate the memory resource that holds the MSI-X table and pending bit array (PBA) before calling this function if the device supports MSI-X. - pci_release_msi(dev) backed by PCI_RELEASE_MSI(). This function releases the messages allocated for this device. All of the SYS_RES_IRQ resources need to be released for this function to succeed. - pci_msi_count(dev) backed by PCI_MSI_COUNT(). This function returns the maximum number of MSI or MSI-X messages supported by this device. MSI-X is preferred if present, but this function will honor the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. This function should return the largest value that pci_alloc_msi() can return (assuming the MD code is able to allocate sufficient backing resources for all of the messages). - Add default implementations for these 3 methods to the pci_driver generic PCI bus driver. (The various other PCI bus drivers such as for ACPI and OFW will inherit these default implementations.) This default implementation depends on 4 new pcib_if methods that bubble up through the PCI bridges to the MD code to allocate IRQ values and perform any needed MD setup code needed: - PCIB_ALLOC_MSI() attempts to allocate a group of MSI messages. - PCIB_RELEASE_MSI() releases a group of MSI messages. - PCIB_ALLOC_MSIX() attempts to allocate a single MSI-X message. - PCIB_RELEASE_MSIX() releases a single MSI-X message. - Add default implementations for these 4 methods that just pass the request up to the parent bus's parent bridge driver and use the default implementation in the various MI PCI bridge drivers. - Add MI functions for use by MD code when managing MSI and MSI-X interrupts: - pci_enable_msi(dev, address, data) programs the MSI capability address and data registers for a group of MSI messages - pci_enable_msix(dev, index, address, data) initializes a single MSI-X message in the MSI-X table - pci_mask_msix(dev, index) masks a single MSI-X message - pci_unmask_msix(dev, index) unmasks a single MSI-X message - pci_pending_msix(dev, index) returns true if the specified MSI-X message is currently pending - Save the MSI capability address and data registers in the pci_cfgreg block in a PCI devices ivars and restore the values when a device is resumed. Note that the MSI-X table is not currently restored during resume. - Add constants for MSI-X register offsets and fields. - Record interesting data about any MSI-X capability blocks we come across in the pci_cfgreg block in the ivars for PCI devices. Tested on: em (i386, MSI), bce (amd64/i386, MSI), mpt (amd64, MSI-X) Reviewed by: scottl, grehan, jfv MFC after: 2 months |
| H A D | pci_pci.c | diff 164264 Mon Nov 13 19:47:30 MST 2006 jhb First cut at MI support for PCI Message Signalled Interrupts (MSI): - Add 3 new functions to the pci_if interface along with suitable wrappers to provide the device driver visible API: - pci_alloc_msi(dev, int *count) backed by PCI_ALLOC_MSI(). '*count' here is an in and out parameter. The driver stores the desired number of messages in '*count' before calling the function. On success, '*count' holds the number of messages allocated to the device. Also on success, the driver can access the messages as SYS_RES_IRQ resources starting at rid 1. Note that the legacy INTx interrupt resource will not be available when using MSI. Note that this function will allocate either MSI or MSI-X messages depending on the devices capabilities and the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. Also note that the driver should activate the memory resource that holds the MSI-X table and pending bit array (PBA) before calling this function if the device supports MSI-X. - pci_release_msi(dev) backed by PCI_RELEASE_MSI(). This function releases the messages allocated for this device. All of the SYS_RES_IRQ resources need to be released for this function to succeed. - pci_msi_count(dev) backed by PCI_MSI_COUNT(). This function returns the maximum number of MSI or MSI-X messages supported by this device. MSI-X is preferred if present, but this function will honor the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. This function should return the largest value that pci_alloc_msi() can return (assuming the MD code is able to allocate sufficient backing resources for all of the messages). - Add default implementations for these 3 methods to the pci_driver generic PCI bus driver. (The various other PCI bus drivers such as for ACPI and OFW will inherit these default implementations.) This default implementation depends on 4 new pcib_if methods that bubble up through the PCI bridges to the MD code to allocate IRQ values and perform any needed MD setup code needed: - PCIB_ALLOC_MSI() attempts to allocate a group of MSI messages. - PCIB_RELEASE_MSI() releases a group of MSI messages. - PCIB_ALLOC_MSIX() attempts to allocate a single MSI-X message. - PCIB_RELEASE_MSIX() releases a single MSI-X message. - Add default implementations for these 4 methods that just pass the request up to the parent bus's parent bridge driver and use the default implementation in the various MI PCI bridge drivers. - Add MI functions for use by MD code when managing MSI and MSI-X interrupts: - pci_enable_msi(dev, address, data) programs the MSI capability address and data registers for a group of MSI messages - pci_enable_msix(dev, index, address, data) initializes a single MSI-X message in the MSI-X table - pci_mask_msix(dev, index) masks a single MSI-X message - pci_unmask_msix(dev, index) unmasks a single MSI-X message - pci_pending_msix(dev, index) returns true if the specified MSI-X message is currently pending - Save the MSI capability address and data registers in the pci_cfgreg block in a PCI devices ivars and restore the values when a device is resumed. Note that the MSI-X table is not currently restored during resume. - Add constants for MSI-X register offsets and fields. - Record interesting data about any MSI-X capability blocks we come across in the pci_cfgreg block in the ivars for PCI devices. Tested on: em (i386, MSI), bce (amd64/i386, MSI), mpt (amd64, MSI-X) Reviewed by: scottl, grehan, jfv MFC after: 2 months |
| H A D | pci_subr.c | diff 164264 Mon Nov 13 19:47:30 MST 2006 jhb First cut at MI support for PCI Message Signalled Interrupts (MSI): - Add 3 new functions to the pci_if interface along with suitable wrappers to provide the device driver visible API: - pci_alloc_msi(dev, int *count) backed by PCI_ALLOC_MSI(). '*count' here is an in and out parameter. The driver stores the desired number of messages in '*count' before calling the function. On success, '*count' holds the number of messages allocated to the device. Also on success, the driver can access the messages as SYS_RES_IRQ resources starting at rid 1. Note that the legacy INTx interrupt resource will not be available when using MSI. Note that this function will allocate either MSI or MSI-X messages depending on the devices capabilities and the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. Also note that the driver should activate the memory resource that holds the MSI-X table and pending bit array (PBA) before calling this function if the device supports MSI-X. - pci_release_msi(dev) backed by PCI_RELEASE_MSI(). This function releases the messages allocated for this device. All of the SYS_RES_IRQ resources need to be released for this function to succeed. - pci_msi_count(dev) backed by PCI_MSI_COUNT(). This function returns the maximum number of MSI or MSI-X messages supported by this device. MSI-X is preferred if present, but this function will honor the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. This function should return the largest value that pci_alloc_msi() can return (assuming the MD code is able to allocate sufficient backing resources for all of the messages). - Add default implementations for these 3 methods to the pci_driver generic PCI bus driver. (The various other PCI bus drivers such as for ACPI and OFW will inherit these default implementations.) This default implementation depends on 4 new pcib_if methods that bubble up through the PCI bridges to the MD code to allocate IRQ values and perform any needed MD setup code needed: - PCIB_ALLOC_MSI() attempts to allocate a group of MSI messages. - PCIB_RELEASE_MSI() releases a group of MSI messages. - PCIB_ALLOC_MSIX() attempts to allocate a single MSI-X message. - PCIB_RELEASE_MSIX() releases a single MSI-X message. - Add default implementations for these 4 methods that just pass the request up to the parent bus's parent bridge driver and use the default implementation in the various MI PCI bridge drivers. - Add MI functions for use by MD code when managing MSI and MSI-X interrupts: - pci_enable_msi(dev, address, data) programs the MSI capability address and data registers for a group of MSI messages - pci_enable_msix(dev, index, address, data) initializes a single MSI-X message in the MSI-X table - pci_mask_msix(dev, index) masks a single MSI-X message - pci_unmask_msix(dev, index) unmasks a single MSI-X message - pci_pending_msix(dev, index) returns true if the specified MSI-X message is currently pending - Save the MSI capability address and data registers in the pci_cfgreg block in a PCI devices ivars and restore the values when a device is resumed. Note that the MSI-X table is not currently restored during resume. - Add constants for MSI-X register offsets and fields. - Record interesting data about any MSI-X capability blocks we come across in the pci_cfgreg block in the ivars for PCI devices. Tested on: em (i386, MSI), bce (amd64/i386, MSI), mpt (amd64, MSI-X) Reviewed by: scottl, grehan, jfv MFC after: 2 months |
| H A D | pcivar.h | diff 164264 Mon Nov 13 19:47:30 MST 2006 jhb First cut at MI support for PCI Message Signalled Interrupts (MSI): - Add 3 new functions to the pci_if interface along with suitable wrappers to provide the device driver visible API: - pci_alloc_msi(dev, int *count) backed by PCI_ALLOC_MSI(). '*count' here is an in and out parameter. The driver stores the desired number of messages in '*count' before calling the function. On success, '*count' holds the number of messages allocated to the device. Also on success, the driver can access the messages as SYS_RES_IRQ resources starting at rid 1. Note that the legacy INTx interrupt resource will not be available when using MSI. Note that this function will allocate either MSI or MSI-X messages depending on the devices capabilities and the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. Also note that the driver should activate the memory resource that holds the MSI-X table and pending bit array (PBA) before calling this function if the device supports MSI-X. - pci_release_msi(dev) backed by PCI_RELEASE_MSI(). This function releases the messages allocated for this device. All of the SYS_RES_IRQ resources need to be released for this function to succeed. - pci_msi_count(dev) backed by PCI_MSI_COUNT(). This function returns the maximum number of MSI or MSI-X messages supported by this device. MSI-X is preferred if present, but this function will honor the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. This function should return the largest value that pci_alloc_msi() can return (assuming the MD code is able to allocate sufficient backing resources for all of the messages). - Add default implementations for these 3 methods to the pci_driver generic PCI bus driver. (The various other PCI bus drivers such as for ACPI and OFW will inherit these default implementations.) This default implementation depends on 4 new pcib_if methods that bubble up through the PCI bridges to the MD code to allocate IRQ values and perform any needed MD setup code needed: - PCIB_ALLOC_MSI() attempts to allocate a group of MSI messages. - PCIB_RELEASE_MSI() releases a group of MSI messages. - PCIB_ALLOC_MSIX() attempts to allocate a single MSI-X message. - PCIB_RELEASE_MSIX() releases a single MSI-X message. - Add default implementations for these 4 methods that just pass the request up to the parent bus's parent bridge driver and use the default implementation in the various MI PCI bridge drivers. - Add MI functions for use by MD code when managing MSI and MSI-X interrupts: - pci_enable_msi(dev, address, data) programs the MSI capability address and data registers for a group of MSI messages - pci_enable_msix(dev, index, address, data) initializes a single MSI-X message in the MSI-X table - pci_mask_msix(dev, index) masks a single MSI-X message - pci_unmask_msix(dev, index) unmasks a single MSI-X message - pci_pending_msix(dev, index) returns true if the specified MSI-X message is currently pending - Save the MSI capability address and data registers in the pci_cfgreg block in a PCI devices ivars and restore the values when a device is resumed. Note that the MSI-X table is not currently restored during resume. - Add constants for MSI-X register offsets and fields. - Record interesting data about any MSI-X capability blocks we come across in the pci_cfgreg block in the ivars for PCI devices. Tested on: em (i386, MSI), bce (amd64/i386, MSI), mpt (amd64, MSI-X) Reviewed by: scottl, grehan, jfv MFC after: 2 months |
| H A D | pci.c | diff 164264 Mon Nov 13 19:47:30 MST 2006 jhb First cut at MI support for PCI Message Signalled Interrupts (MSI): - Add 3 new functions to the pci_if interface along with suitable wrappers to provide the device driver visible API: - pci_alloc_msi(dev, int *count) backed by PCI_ALLOC_MSI(). '*count' here is an in and out parameter. The driver stores the desired number of messages in '*count' before calling the function. On success, '*count' holds the number of messages allocated to the device. Also on success, the driver can access the messages as SYS_RES_IRQ resources starting at rid 1. Note that the legacy INTx interrupt resource will not be available when using MSI. Note that this function will allocate either MSI or MSI-X messages depending on the devices capabilities and the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. Also note that the driver should activate the memory resource that holds the MSI-X table and pending bit array (PBA) before calling this function if the device supports MSI-X. - pci_release_msi(dev) backed by PCI_RELEASE_MSI(). This function releases the messages allocated for this device. All of the SYS_RES_IRQ resources need to be released for this function to succeed. - pci_msi_count(dev) backed by PCI_MSI_COUNT(). This function returns the maximum number of MSI or MSI-X messages supported by this device. MSI-X is preferred if present, but this function will honor the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. This function should return the largest value that pci_alloc_msi() can return (assuming the MD code is able to allocate sufficient backing resources for all of the messages). - Add default implementations for these 3 methods to the pci_driver generic PCI bus driver. (The various other PCI bus drivers such as for ACPI and OFW will inherit these default implementations.) This default implementation depends on 4 new pcib_if methods that bubble up through the PCI bridges to the MD code to allocate IRQ values and perform any needed MD setup code needed: - PCIB_ALLOC_MSI() attempts to allocate a group of MSI messages. - PCIB_RELEASE_MSI() releases a group of MSI messages. - PCIB_ALLOC_MSIX() attempts to allocate a single MSI-X message. - PCIB_RELEASE_MSIX() releases a single MSI-X message. - Add default implementations for these 4 methods that just pass the request up to the parent bus's parent bridge driver and use the default implementation in the various MI PCI bridge drivers. - Add MI functions for use by MD code when managing MSI and MSI-X interrupts: - pci_enable_msi(dev, address, data) programs the MSI capability address and data registers for a group of MSI messages - pci_enable_msix(dev, index, address, data) initializes a single MSI-X message in the MSI-X table - pci_mask_msix(dev, index) masks a single MSI-X message - pci_unmask_msix(dev, index) unmasks a single MSI-X message - pci_pending_msix(dev, index) returns true if the specified MSI-X message is currently pending - Save the MSI capability address and data registers in the pci_cfgreg block in a PCI devices ivars and restore the values when a device is resumed. Note that the MSI-X table is not currently restored during resume. - Add constants for MSI-X register offsets and fields. - Record interesting data about any MSI-X capability blocks we come across in the pci_cfgreg block in the ivars for PCI devices. Tested on: em (i386, MSI), bce (amd64/i386, MSI), mpt (amd64, MSI-X) Reviewed by: scottl, grehan, jfv MFC after: 2 months |
| /freebsd-9.3-release/sys/dev/acpica/ | ||
| H A D | acpi_pcib_pci.c | diff 164264 Mon Nov 13 19:47:30 MST 2006 jhb First cut at MI support for PCI Message Signalled Interrupts (MSI): - Add 3 new functions to the pci_if interface along with suitable wrappers to provide the device driver visible API: - pci_alloc_msi(dev, int *count) backed by PCI_ALLOC_MSI(). '*count' here is an in and out parameter. The driver stores the desired number of messages in '*count' before calling the function. On success, '*count' holds the number of messages allocated to the device. Also on success, the driver can access the messages as SYS_RES_IRQ resources starting at rid 1. Note that the legacy INTx interrupt resource will not be available when using MSI. Note that this function will allocate either MSI or MSI-X messages depending on the devices capabilities and the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. Also note that the driver should activate the memory resource that holds the MSI-X table and pending bit array (PBA) before calling this function if the device supports MSI-X. - pci_release_msi(dev) backed by PCI_RELEASE_MSI(). This function releases the messages allocated for this device. All of the SYS_RES_IRQ resources need to be released for this function to succeed. - pci_msi_count(dev) backed by PCI_MSI_COUNT(). This function returns the maximum number of MSI or MSI-X messages supported by this device. MSI-X is preferred if present, but this function will honor the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. This function should return the largest value that pci_alloc_msi() can return (assuming the MD code is able to allocate sufficient backing resources for all of the messages). - Add default implementations for these 3 methods to the pci_driver generic PCI bus driver. (The various other PCI bus drivers such as for ACPI and OFW will inherit these default implementations.) This default implementation depends on 4 new pcib_if methods that bubble up through the PCI bridges to the MD code to allocate IRQ values and perform any needed MD setup code needed: - PCIB_ALLOC_MSI() attempts to allocate a group of MSI messages. - PCIB_RELEASE_MSI() releases a group of MSI messages. - PCIB_ALLOC_MSIX() attempts to allocate a single MSI-X message. - PCIB_RELEASE_MSIX() releases a single MSI-X message. - Add default implementations for these 4 methods that just pass the request up to the parent bus's parent bridge driver and use the default implementation in the various MI PCI bridge drivers. - Add MI functions for use by MD code when managing MSI and MSI-X interrupts: - pci_enable_msi(dev, address, data) programs the MSI capability address and data registers for a group of MSI messages - pci_enable_msix(dev, index, address, data) initializes a single MSI-X message in the MSI-X table - pci_mask_msix(dev, index) masks a single MSI-X message - pci_unmask_msix(dev, index) unmasks a single MSI-X message - pci_pending_msix(dev, index) returns true if the specified MSI-X message is currently pending - Save the MSI capability address and data registers in the pci_cfgreg block in a PCI devices ivars and restore the values when a device is resumed. Note that the MSI-X table is not currently restored during resume. - Add constants for MSI-X register offsets and fields. - Record interesting data about any MSI-X capability blocks we come across in the pci_cfgreg block in the ivars for PCI devices. Tested on: em (i386, MSI), bce (amd64/i386, MSI), mpt (amd64, MSI-X) Reviewed by: scottl, grehan, jfv MFC after: 2 months |
| H A D | acpi_pcib_acpi.c | diff 164264 Mon Nov 13 19:47:30 MST 2006 jhb First cut at MI support for PCI Message Signalled Interrupts (MSI): - Add 3 new functions to the pci_if interface along with suitable wrappers to provide the device driver visible API: - pci_alloc_msi(dev, int *count) backed by PCI_ALLOC_MSI(). '*count' here is an in and out parameter. The driver stores the desired number of messages in '*count' before calling the function. On success, '*count' holds the number of messages allocated to the device. Also on success, the driver can access the messages as SYS_RES_IRQ resources starting at rid 1. Note that the legacy INTx interrupt resource will not be available when using MSI. Note that this function will allocate either MSI or MSI-X messages depending on the devices capabilities and the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. Also note that the driver should activate the memory resource that holds the MSI-X table and pending bit array (PBA) before calling this function if the device supports MSI-X. - pci_release_msi(dev) backed by PCI_RELEASE_MSI(). This function releases the messages allocated for this device. All of the SYS_RES_IRQ resources need to be released for this function to succeed. - pci_msi_count(dev) backed by PCI_MSI_COUNT(). This function returns the maximum number of MSI or MSI-X messages supported by this device. MSI-X is preferred if present, but this function will honor the 'hw.pci.enable_msix' and 'hw.pci.enable_msi' tunables. This function should return the largest value that pci_alloc_msi() can return (assuming the MD code is able to allocate sufficient backing resources for all of the messages). - Add default implementations for these 3 methods to the pci_driver generic PCI bus driver. (The various other PCI bus drivers such as for ACPI and OFW will inherit these default implementations.) This default implementation depends on 4 new pcib_if methods that bubble up through the PCI bridges to the MD code to allocate IRQ values and perform any needed MD setup code needed: - PCIB_ALLOC_MSI() attempts to allocate a group of MSI messages. - PCIB_RELEASE_MSI() releases a group of MSI messages. - PCIB_ALLOC_MSIX() attempts to allocate a single MSI-X message. - PCIB_RELEASE_MSIX() releases a single MSI-X message. - Add default implementations for these 4 methods that just pass the request up to the parent bus's parent bridge driver and use the default implementation in the various MI PCI bridge drivers. - Add MI functions for use by MD code when managing MSI and MSI-X interrupts: - pci_enable_msi(dev, address, data) programs the MSI capability address and data registers for a group of MSI messages - pci_enable_msix(dev, index, address, data) initializes a single MSI-X message in the MSI-X table - pci_mask_msix(dev, index) masks a single MSI-X message - pci_unmask_msix(dev, index) unmasks a single MSI-X message - pci_pending_msix(dev, index) returns true if the specified MSI-X message is currently pending - Save the MSI capability address and data registers in the pci_cfgreg block in a PCI devices ivars and restore the values when a device is resumed. Note that the MSI-X table is not currently restored during resume. - Add constants for MSI-X register offsets and fields. - Record interesting data about any MSI-X capability blocks we come across in the pci_cfgreg block in the ivars for PCI devices. Tested on: em (i386, MSI), bce (amd64/i386, MSI), mpt (amd64, MSI-X) Reviewed by: scottl, grehan, jfv MFC after: 2 months |
Completed in 304 milliseconds