| /haiku/src/add-ons/kernel/drivers/network/wlan/atheroswifi/dev/ath/ |
| H A D | if_ath_tx_ht.c | 492 * on highest rate in rate series (i.e. first rate) to determine
559 * It's the lowest of the four rate series 4ms frame length.
606 * Setup a 11n rate series structure
610 * This uses the rate series stuf from ath_tx_rate_fill_rcflags().
617 struct ath_buf *bf, HAL_11N_RATE_SERIES *series)
632 * If this is the first frame in an aggregate series,
644 memset(series, 0, sizeof(HAL_11N_RATE_SERIES) * 4);
650 series[i].Tries = rc[i].tries;
659 series[i].ChSel = sc->sc_cur_txchainmask;
662 * Setup rate and TX power cap for this series
616 ath_rateseries_setup(struct ath_softc *sc, struct ieee80211_node *ni, struct ath_buf *bf, HAL_11N_RATE_SERIES *series) argument
718 ath_rateseries_print(struct ath_softc *sc, HAL_11N_RATE_SERIES *series) argument
746 HAL_11N_RATE_SERIES series[4]; local
[all...] |
| /haiku/src/add-ons/kernel/drivers/network/wlan/atheroswifi/contrib/ath_hal/ar9300/ |
| H A D | ar9300_xmit_ds.c | 707 HAL_11N_RATE_SERIES series[],
747 tx_mode = ar9300_get_tx_mode(series[0].RateFlags);
748 txpower = ar9300_get_rate_txpower(ah, mode, series[0].RateIndex,
749 series[0].ChSel, tx_mode);
755 set_11n_tx_power(0, AH_MIN(txpower, series[0].tx_power_cap));
761 ads->ds_ctl13 = set_11n_tries(series, 0)
762 | set_11n_tries(series, 1)
763 | set_11n_tries(series, 2)
764 | set_11n_tries(series, 3)
768 ads->ds_ctl14 = set_11n_rate(series,
700 ar9300_set_11n_rate_scenario( struct ath_hal *ah, void *ds, void *lastds, u_int dur_update_en, u_int rts_cts_rate, u_int rts_cts_duration, HAL_11N_RATE_SERIES series[], u_int nseries, u_int flags, u_int32_t smart_antenna) argument
[all...] |
| H A D | ar9300_freebsd.h | 50 struct ath_desc *, u_int, u_int, HAL_11N_RATE_SERIES series[],
|
| H A D | ar9300_freebsd.c | 801 u_int durUpdateEn, u_int rtsctsRate, HAL_11N_RATE_SERIES series[],
807 rtsctsRate, 0, series, nseries, flags, 0); local
800 ar9300_freebsd_set_11n_rate_scenario(struct ath_hal *ah, struct ath_desc *ds, u_int durUpdateEn, u_int rtsctsRate, HAL_11N_RATE_SERIES series[], u_int nseries, u_int flags) argument
|
| H A D | ar9300desc.h | 541 void *lastds, u_int dur_update_en, u_int rts_cts_rate, u_int rts_cts_duration, HAL_11N_RATE_SERIES series[],
|
| H A D | ar9300.h | 1620 #define ar9300_set_11n_txbf_sounding(ah, ds, series, cec, opt)
|
| /haiku/src/add-ons/kernel/drivers/network/wlan/atheroswifi/dev/ath/ath_hal/ar5416/ |
| H A D | ar5416_xmit.c | 768 * ``alternate'' if it wasn't the series 0 rate.
801 * final series used. When doing multi-rate retry we must
803 * each series that was fully-processed. Beware that this
877 HAL_11N_RATE_SERIES series[], u_int nseries, u_int flags)
907 ads->ds_ctl2 = set11nTries(series, 0)
908 | set11nTries(series, 1)
909 | set11nTries(series, 2)
910 | set11nTries(series, 3)
913 ads->ds_ctl3 = set11nRate(series, 0)
914 | set11nRate(series,
875 ar5416Set11nRateScenario(struct ath_hal *ah, struct ath_desc *ds, u_int durUpdateEn, u_int rtsctsRate, HAL_11N_RATE_SERIES series[], u_int nseries, u_int flags) argument
[all...] |
| H A D | ar5416.h | 409 u_int durUpdateEn, u_int rtsctsRate, HAL_11N_RATE_SERIES series[],
|
| /haiku/src/add-ons/kernel/drivers/network/wlan/atheroswifi/dev/ath/ath_rate/sample/ |
| H A D | sample.c | 946 s1code, sched->t1, /* series 1 */
947 s2code, sched->t2, /* series 2 */
948 s3code, sched->t3); /* series 3 */
1084 badrate(struct ath_softc *sc, int series, int hwrate, int tries, int status) argument
1088 "bad series%d hwrate 0x%x, tries %u ts_status 0x%x\n",
1089 series, hwrate, tries, status);
|