Copy stable/11@r303970 to releng/11.0 as part of the 11.0-RELEASE
cycle.

Prune svn:mergeinfo from the new branch, and rename it to RC1.

Update __FreeBSD_version.

Use the quarterly branch for the default FreeBSD.conf pkg(8) repo and
the dvd1.iso packages population.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head@r302406 to stable/11 as part of the 11.0-RELEASE cycle.
Prune svn:mergeinfo from the new branch, as nothing has been merged
here.

Additional commits post-branch will follow.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Enable USB PHY regulators when requested by the host controller driver.

Previously the USB PHY driver would enable all regulators at attach time.
This prevented boards from booting when powered by the USB OTG port, as
it didn't take VBUS presence into consideration.

Add support for Allwinner H3 SoC.
For now clocks, GPIO, Pinmux, UART, MMC, EHCI is supported.
Tested on OrangePi-One

Reviewed by: jmcneill
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D6311

Add support for the Allwinner A83T (sun8iw6p1) SoC.

Clocks, GPIO, UART, SD card / eMMC, USB, watchdog, and ethernet are
supported. Note that the A83T contains two clusters of four Cortex-A7
CPUs, and only CPUs in first cluster are started for now.

Tested on a Sinovoip Banana Pi BPI-M3.

Convert Allwinner port to extres clk/hwreset/regulator APIs.

Reviewed by: andrew, gonzo, Emmanuel Vadot <manu@bidouilliste.com>
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5752

Add support to enable/disable both the EHCI and OHCI Allwinner clocks. This
adds a lock to ensure only a single device is accessing the hardware. A
reference count is added to only enable when we start to use the clock,
and to disable after we have finished needing the clock.

This was extracted from a larger review to add OHCI support to the
Allwinner SoCs.

Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed by: jmcneill
X-Differential Revision: https://reviews.freebsd.org/D5481

Add support for Allwinner A31/A31s EHCI controller and USB PHY.

Reviewed by: andrew, Emmanuel Vadot <manu@bidouilliste.com>
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5467

Update of the Allwinner drivers to:
* Use the Linux compat string
* Use EARLY_DRIVER_MODULE to attach at the right time
* Add a generic A10 kernel config file
* A20 now use generic_timer
* Add two new dts files for Olimex boards
* Update our custom DTS file for A10 and A20 to use the same compatible
property names as the vendor ones.

Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4792

Add 64-bit DMA support in the XHCI controller driver.
- Fix some comments and whitespace while at it.

MFC after: 1 month
Submitted by: marius@

Switch to my freebsd.org emal address in copyright.

Approved by: stas (mentor)

Follow r261352 by updating all drivers which are children of simplebus
to check the status property in their probe routines.

Simplebus used to only instantiate its children whose status="okay"
but that was improper behavior, fixed in r261352. Now that it doesn't
check anymore and probes all its children; the children all have to
do the check because really only the children know how to properly
interpret their status property strings.

Right now all existing drivers only understand "okay" versus something-
that's-not-okay, so they all use the new ofw_bus_status_okay() helper.

Enable USB1 (which is EHCI0) for Allwinner A10

Tested by: ganbold@

Use and set gpio pin to high to power up usb.

Approved by: gonzo@

Add simple clock driver and ehci glue code for a10
Update dts and kernel config

Approved by: gonzo@