if_ti.c revision 227091
1/*- 2 * Copyright (c) 1997, 1998, 1999 3 * Bill Paul <wpaul@ctr.columbia.edu>. All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions 7 * are met: 8 * 1. Redistributions of source code must retain the above copyright 9 * notice, this list of conditions and the following disclaimer. 10 * 2. Redistributions in binary form must reproduce the above copyright 11 * notice, this list of conditions and the following disclaimer in the 12 * documentation and/or other materials provided with the distribution. 13 * 3. All advertising materials mentioning features or use of this software 14 * must display the following acknowledgement: 15 * This product includes software developed by Bill Paul. 16 * 4. Neither the name of the author nor the names of any co-contributors 17 * may be used to endorse or promote products derived from this software 18 * without specific prior written permission. 19 * 20 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND 21 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD 24 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 30 * THE POSSIBILITY OF SUCH DAMAGE. 31 */ 32 33/* 34 * Alteon Networks Tigon PCI gigabit ethernet driver for FreeBSD. 35 * Manuals, sample driver and firmware source kits are available 36 * from http://www.alteon.com/support/openkits. 37 * 38 * Written by Bill Paul <wpaul@ctr.columbia.edu> 39 * Electrical Engineering Department 40 * Columbia University, New York City 41 */ 42 43/* 44 * The Alteon Networks Tigon chip contains an embedded R4000 CPU, 45 * gigabit MAC, dual DMA channels and a PCI interface unit. NICs 46 * using the Tigon may have anywhere from 512K to 2MB of SRAM. The 47 * Tigon supports hardware IP, TCP and UCP checksumming, multicast 48 * filtering and jumbo (9014 byte) frames. The hardware is largely 49 * controlled by firmware, which must be loaded into the NIC during 50 * initialization. 51 * 52 * The Tigon 2 contains 2 R4000 CPUs and requires a newer firmware 53 * revision, which supports new features such as extended commands, 54 * extended jumbo receive ring desciptors and a mini receive ring. 55 * 56 * Alteon Networks is to be commended for releasing such a vast amount 57 * of development material for the Tigon NIC without requiring an NDA 58 * (although they really should have done it a long time ago). With 59 * any luck, the other vendors will finally wise up and follow Alteon's 60 * stellar example. 61 * 62 * The firmware for the Tigon 1 and 2 NICs is compiled directly into 63 * this driver by #including it as a C header file. This bloats the 64 * driver somewhat, but it's the easiest method considering that the 65 * driver code and firmware code need to be kept in sync. The source 66 * for the firmware is not provided with the FreeBSD distribution since 67 * compiling it requires a GNU toolchain targeted for mips-sgi-irix5.3. 68 * 69 * The following people deserve special thanks: 70 * - Terry Murphy of 3Com, for providing a 3c985 Tigon 1 board 71 * for testing 72 * - Raymond Lee of Netgear, for providing a pair of Netgear 73 * GA620 Tigon 2 boards for testing 74 * - Ulf Zimmermann, for bringing the GA260 to my attention and 75 * convincing me to write this driver. 76 * - Andrew Gallatin for providing FreeBSD/Alpha support. 77 */ 78 79#include <sys/cdefs.h> 80__FBSDID("$FreeBSD: head/sys/dev/ti/if_ti.c 227091 2011-11-04 20:25:30Z yongari $"); 81 82#include "opt_ti.h" 83 84#include <sys/param.h> 85#include <sys/systm.h> 86#include <sys/sockio.h> 87#include <sys/mbuf.h> 88#include <sys/malloc.h> 89#include <sys/kernel.h> 90#include <sys/module.h> 91#include <sys/socket.h> 92#include <sys/queue.h> 93#include <sys/conf.h> 94#include <sys/sf_buf.h> 95 96#include <net/if.h> 97#include <net/if_arp.h> 98#include <net/ethernet.h> 99#include <net/if_dl.h> 100#include <net/if_media.h> 101#include <net/if_types.h> 102#include <net/if_vlan_var.h> 103 104#include <net/bpf.h> 105 106#include <netinet/in_systm.h> 107#include <netinet/in.h> 108#include <netinet/ip.h> 109 110#include <machine/bus.h> 111#include <machine/resource.h> 112#include <sys/bus.h> 113#include <sys/rman.h> 114 115/* #define TI_PRIVATE_JUMBOS */ 116#ifndef TI_PRIVATE_JUMBOS 117#include <vm/vm.h> 118#include <vm/vm_page.h> 119#endif 120 121#include <dev/pci/pcireg.h> 122#include <dev/pci/pcivar.h> 123 124#include <sys/tiio.h> 125#include <dev/ti/if_tireg.h> 126#include <dev/ti/ti_fw.h> 127#include <dev/ti/ti_fw2.h> 128 129#define TI_CSUM_FEATURES (CSUM_IP | CSUM_TCP | CSUM_UDP | CSUM_IP_FRAGS) 130/* 131 * We can only turn on header splitting if we're using extended receive 132 * BDs. 133 */ 134#if defined(TI_JUMBO_HDRSPLIT) && defined(TI_PRIVATE_JUMBOS) 135#error "options TI_JUMBO_HDRSPLIT and TI_PRIVATE_JUMBOS are mutually exclusive" 136#endif /* TI_JUMBO_HDRSPLIT && TI_JUMBO_HDRSPLIT */ 137 138typedef enum { 139 TI_SWAP_HTON, 140 TI_SWAP_NTOH 141} ti_swap_type; 142 143/* 144 * Various supported device vendors/types and their names. 145 */ 146 147static const struct ti_type const ti_devs[] = { 148 { ALT_VENDORID, ALT_DEVICEID_ACENIC, 149 "Alteon AceNIC 1000baseSX Gigabit Ethernet" }, 150 { ALT_VENDORID, ALT_DEVICEID_ACENIC_COPPER, 151 "Alteon AceNIC 1000baseT Gigabit Ethernet" }, 152 { TC_VENDORID, TC_DEVICEID_3C985, 153 "3Com 3c985-SX Gigabit Ethernet" }, 154 { NG_VENDORID, NG_DEVICEID_GA620, 155 "Netgear GA620 1000baseSX Gigabit Ethernet" }, 156 { NG_VENDORID, NG_DEVICEID_GA620T, 157 "Netgear GA620 1000baseT Gigabit Ethernet" }, 158 { SGI_VENDORID, SGI_DEVICEID_TIGON, 159 "Silicon Graphics Gigabit Ethernet" }, 160 { DEC_VENDORID, DEC_DEVICEID_FARALLON_PN9000SX, 161 "Farallon PN9000SX Gigabit Ethernet" }, 162 { 0, 0, NULL } 163}; 164 165 166static d_open_t ti_open; 167static d_close_t ti_close; 168static d_ioctl_t ti_ioctl2; 169 170static struct cdevsw ti_cdevsw = { 171 .d_version = D_VERSION, 172 .d_flags = 0, 173 .d_open = ti_open, 174 .d_close = ti_close, 175 .d_ioctl = ti_ioctl2, 176 .d_name = "ti", 177}; 178 179static int ti_probe(device_t); 180static int ti_attach(device_t); 181static int ti_detach(device_t); 182static void ti_txeof(struct ti_softc *); 183static void ti_rxeof(struct ti_softc *); 184 185static void ti_stats_update(struct ti_softc *); 186static int ti_encap(struct ti_softc *, struct mbuf **); 187 188static void ti_intr(void *); 189static void ti_start(struct ifnet *); 190static void ti_start_locked(struct ifnet *); 191static int ti_ioctl(struct ifnet *, u_long, caddr_t); 192static void ti_init(void *); 193static void ti_init_locked(void *); 194static void ti_init2(struct ti_softc *); 195static void ti_stop(struct ti_softc *); 196static void ti_watchdog(void *); 197static int ti_shutdown(device_t); 198static int ti_ifmedia_upd(struct ifnet *); 199static void ti_ifmedia_sts(struct ifnet *, struct ifmediareq *); 200 201static uint32_t ti_eeprom_putbyte(struct ti_softc *, int); 202static uint8_t ti_eeprom_getbyte(struct ti_softc *, int, uint8_t *); 203static int ti_read_eeprom(struct ti_softc *, caddr_t, int, int); 204 205static void ti_add_mcast(struct ti_softc *, struct ether_addr *); 206static void ti_del_mcast(struct ti_softc *, struct ether_addr *); 207static void ti_setmulti(struct ti_softc *); 208 209static void ti_mem_read(struct ti_softc *, uint32_t, uint32_t, void *); 210static void ti_mem_write(struct ti_softc *, uint32_t, uint32_t, void *); 211static void ti_mem_zero(struct ti_softc *, uint32_t, uint32_t); 212static int ti_copy_mem(struct ti_softc *, uint32_t, uint32_t, caddr_t, int, 213 int); 214static int ti_copy_scratch(struct ti_softc *, uint32_t, uint32_t, caddr_t, 215 int, int, int); 216static int ti_bcopy_swap(const void *, void *, size_t, ti_swap_type); 217static void ti_loadfw(struct ti_softc *); 218static void ti_cmd(struct ti_softc *, struct ti_cmd_desc *); 219static void ti_cmd_ext(struct ti_softc *, struct ti_cmd_desc *, caddr_t, int); 220static void ti_handle_events(struct ti_softc *); 221static int ti_alloc_dmamaps(struct ti_softc *); 222static void ti_free_dmamaps(struct ti_softc *); 223static int ti_alloc_jumbo_mem(struct ti_softc *); 224#ifdef TI_PRIVATE_JUMBOS 225static void *ti_jalloc(struct ti_softc *); 226static void ti_jfree(void *, void *); 227#endif /* TI_PRIVATE_JUMBOS */ 228static int ti_newbuf_std(struct ti_softc *, int, struct mbuf *); 229static int ti_newbuf_mini(struct ti_softc *, int, struct mbuf *); 230static int ti_newbuf_jumbo(struct ti_softc *, int, struct mbuf *); 231static int ti_init_rx_ring_std(struct ti_softc *); 232static void ti_free_rx_ring_std(struct ti_softc *); 233static int ti_init_rx_ring_jumbo(struct ti_softc *); 234static void ti_free_rx_ring_jumbo(struct ti_softc *); 235static int ti_init_rx_ring_mini(struct ti_softc *); 236static void ti_free_rx_ring_mini(struct ti_softc *); 237static void ti_free_tx_ring(struct ti_softc *); 238static int ti_init_tx_ring(struct ti_softc *); 239 240static int ti_64bitslot_war(struct ti_softc *); 241static int ti_chipinit(struct ti_softc *); 242static int ti_gibinit(struct ti_softc *); 243 244#ifdef TI_JUMBO_HDRSPLIT 245static __inline void ti_hdr_split(struct mbuf *top, int hdr_len, int pkt_len, 246 int idx); 247#endif /* TI_JUMBO_HDRSPLIT */ 248 249static device_method_t ti_methods[] = { 250 /* Device interface */ 251 DEVMETHOD(device_probe, ti_probe), 252 DEVMETHOD(device_attach, ti_attach), 253 DEVMETHOD(device_detach, ti_detach), 254 DEVMETHOD(device_shutdown, ti_shutdown), 255 { 0, 0 } 256}; 257 258static driver_t ti_driver = { 259 "ti", 260 ti_methods, 261 sizeof(struct ti_softc) 262}; 263 264static devclass_t ti_devclass; 265 266DRIVER_MODULE(ti, pci, ti_driver, ti_devclass, 0, 0); 267MODULE_DEPEND(ti, pci, 1, 1, 1); 268MODULE_DEPEND(ti, ether, 1, 1, 1); 269 270/* 271 * Send an instruction or address to the EEPROM, check for ACK. 272 */ 273static uint32_t 274ti_eeprom_putbyte(struct ti_softc *sc, int byte) 275{ 276 int i, ack = 0; 277 278 /* 279 * Make sure we're in TX mode. 280 */ 281 TI_SETBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_TXEN); 282 283 /* 284 * Feed in each bit and stobe the clock. 285 */ 286 for (i = 0x80; i; i >>= 1) { 287 if (byte & i) { 288 TI_SETBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_DOUT); 289 } else { 290 TI_CLRBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_DOUT); 291 } 292 DELAY(1); 293 TI_SETBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_CLK); 294 DELAY(1); 295 TI_CLRBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_CLK); 296 } 297 298 /* 299 * Turn off TX mode. 300 */ 301 TI_CLRBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_TXEN); 302 303 /* 304 * Check for ack. 305 */ 306 TI_SETBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_CLK); 307 ack = CSR_READ_4(sc, TI_MISC_LOCAL_CTL) & TI_MLC_EE_DIN; 308 TI_CLRBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_CLK); 309 310 return (ack); 311} 312 313/* 314 * Read a byte of data stored in the EEPROM at address 'addr.' 315 * We have to send two address bytes since the EEPROM can hold 316 * more than 256 bytes of data. 317 */ 318static uint8_t 319ti_eeprom_getbyte(struct ti_softc *sc, int addr, uint8_t *dest) 320{ 321 int i; 322 uint8_t byte = 0; 323 324 EEPROM_START; 325 326 /* 327 * Send write control code to EEPROM. 328 */ 329 if (ti_eeprom_putbyte(sc, EEPROM_CTL_WRITE)) { 330 device_printf(sc->ti_dev, 331 "failed to send write command, status: %x\n", 332 CSR_READ_4(sc, TI_MISC_LOCAL_CTL)); 333 return (1); 334 } 335 336 /* 337 * Send first byte of address of byte we want to read. 338 */ 339 if (ti_eeprom_putbyte(sc, (addr >> 8) & 0xFF)) { 340 device_printf(sc->ti_dev, "failed to send address, status: %x\n", 341 CSR_READ_4(sc, TI_MISC_LOCAL_CTL)); 342 return (1); 343 } 344 /* 345 * Send second byte address of byte we want to read. 346 */ 347 if (ti_eeprom_putbyte(sc, addr & 0xFF)) { 348 device_printf(sc->ti_dev, "failed to send address, status: %x\n", 349 CSR_READ_4(sc, TI_MISC_LOCAL_CTL)); 350 return (1); 351 } 352 353 EEPROM_STOP; 354 EEPROM_START; 355 /* 356 * Send read control code to EEPROM. 357 */ 358 if (ti_eeprom_putbyte(sc, EEPROM_CTL_READ)) { 359 device_printf(sc->ti_dev, 360 "failed to send read command, status: %x\n", 361 CSR_READ_4(sc, TI_MISC_LOCAL_CTL)); 362 return (1); 363 } 364 365 /* 366 * Start reading bits from EEPROM. 367 */ 368 TI_CLRBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_TXEN); 369 for (i = 0x80; i; i >>= 1) { 370 TI_SETBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_CLK); 371 DELAY(1); 372 if (CSR_READ_4(sc, TI_MISC_LOCAL_CTL) & TI_MLC_EE_DIN) 373 byte |= i; 374 TI_CLRBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_CLK); 375 DELAY(1); 376 } 377 378 EEPROM_STOP; 379 380 /* 381 * No ACK generated for read, so just return byte. 382 */ 383 384 *dest = byte; 385 386 return (0); 387} 388 389/* 390 * Read a sequence of bytes from the EEPROM. 391 */ 392static int 393ti_read_eeprom(struct ti_softc *sc, caddr_t dest, int off, int cnt) 394{ 395 int err = 0, i; 396 uint8_t byte = 0; 397 398 for (i = 0; i < cnt; i++) { 399 err = ti_eeprom_getbyte(sc, off + i, &byte); 400 if (err) 401 break; 402 *(dest + i) = byte; 403 } 404 405 return (err ? 1 : 0); 406} 407 408/* 409 * NIC memory read function. 410 * Can be used to copy data from NIC local memory. 411 */ 412static void 413ti_mem_read(struct ti_softc *sc, uint32_t addr, uint32_t len, void *buf) 414{ 415 int segptr, segsize, cnt; 416 char *ptr; 417 418 segptr = addr; 419 cnt = len; 420 ptr = buf; 421 422 while (cnt) { 423 if (cnt < TI_WINLEN) 424 segsize = cnt; 425 else 426 segsize = TI_WINLEN - (segptr % TI_WINLEN); 427 CSR_WRITE_4(sc, TI_WINBASE, (segptr & ~(TI_WINLEN - 1))); 428 bus_space_read_region_4(sc->ti_btag, sc->ti_bhandle, 429 TI_WINDOW + (segptr & (TI_WINLEN - 1)), (uint32_t *)ptr, 430 segsize / 4); 431 ptr += segsize; 432 segptr += segsize; 433 cnt -= segsize; 434 } 435} 436 437 438/* 439 * NIC memory write function. 440 * Can be used to copy data into NIC local memory. 441 */ 442static void 443ti_mem_write(struct ti_softc *sc, uint32_t addr, uint32_t len, void *buf) 444{ 445 int segptr, segsize, cnt; 446 char *ptr; 447 448 segptr = addr; 449 cnt = len; 450 ptr = buf; 451 452 while (cnt) { 453 if (cnt < TI_WINLEN) 454 segsize = cnt; 455 else 456 segsize = TI_WINLEN - (segptr % TI_WINLEN); 457 CSR_WRITE_4(sc, TI_WINBASE, (segptr & ~(TI_WINLEN - 1))); 458 bus_space_write_region_4(sc->ti_btag, sc->ti_bhandle, 459 TI_WINDOW + (segptr & (TI_WINLEN - 1)), (uint32_t *)ptr, 460 segsize / 4); 461 ptr += segsize; 462 segptr += segsize; 463 cnt -= segsize; 464 } 465} 466 467/* 468 * NIC memory read function. 469 * Can be used to clear a section of NIC local memory. 470 */ 471static void 472ti_mem_zero(struct ti_softc *sc, uint32_t addr, uint32_t len) 473{ 474 int segptr, segsize, cnt; 475 476 segptr = addr; 477 cnt = len; 478 479 while (cnt) { 480 if (cnt < TI_WINLEN) 481 segsize = cnt; 482 else 483 segsize = TI_WINLEN - (segptr % TI_WINLEN); 484 CSR_WRITE_4(sc, TI_WINBASE, (segptr & ~(TI_WINLEN - 1))); 485 bus_space_set_region_4(sc->ti_btag, sc->ti_bhandle, 486 TI_WINDOW + (segptr & (TI_WINLEN - 1)), 0, segsize / 4); 487 segptr += segsize; 488 cnt -= segsize; 489 } 490} 491 492static int 493ti_copy_mem(struct ti_softc *sc, uint32_t tigon_addr, uint32_t len, 494 caddr_t buf, int useraddr, int readdata) 495{ 496 int segptr, segsize, cnt; 497 caddr_t ptr; 498 uint32_t origwin; 499 uint8_t tmparray[TI_WINLEN], tmparray2[TI_WINLEN]; 500 int resid, segresid; 501 int first_pass; 502 503 TI_LOCK_ASSERT(sc); 504 505 /* 506 * At the moment, we don't handle non-aligned cases, we just bail. 507 * If this proves to be a problem, it will be fixed. 508 */ 509 if ((readdata == 0) 510 && (tigon_addr & 0x3)) { 511 device_printf(sc->ti_dev, "%s: tigon address %#x isn't " 512 "word-aligned\n", __func__, tigon_addr); 513 device_printf(sc->ti_dev, "%s: unaligned writes aren't " 514 "yet supported\n", __func__); 515 return (EINVAL); 516 } 517 518 segptr = tigon_addr & ~0x3; 519 segresid = tigon_addr - segptr; 520 521 /* 522 * This is the non-aligned amount left over that we'll need to 523 * copy. 524 */ 525 resid = len & 0x3; 526 527 /* Add in the left over amount at the front of the buffer */ 528 resid += segresid; 529 530 cnt = len & ~0x3; 531 /* 532 * If resid + segresid is >= 4, add multiples of 4 to the count and 533 * decrease the residual by that much. 534 */ 535 cnt += resid & ~0x3; 536 resid -= resid & ~0x3; 537 538 ptr = buf; 539 540 first_pass = 1; 541 542 /* 543 * Save the old window base value. 544 */ 545 origwin = CSR_READ_4(sc, TI_WINBASE); 546 547 while (cnt) { 548 bus_size_t ti_offset; 549 550 if (cnt < TI_WINLEN) 551 segsize = cnt; 552 else 553 segsize = TI_WINLEN - (segptr % TI_WINLEN); 554 CSR_WRITE_4(sc, TI_WINBASE, (segptr & ~(TI_WINLEN - 1))); 555 556 ti_offset = TI_WINDOW + (segptr & (TI_WINLEN -1)); 557 558 if (readdata) { 559 560 bus_space_read_region_4(sc->ti_btag, 561 sc->ti_bhandle, ti_offset, 562 (uint32_t *)tmparray, 563 segsize >> 2); 564 if (useraddr) { 565 /* 566 * Yeah, this is a little on the kludgy 567 * side, but at least this code is only 568 * used for debugging. 569 */ 570 ti_bcopy_swap(tmparray, tmparray2, segsize, 571 TI_SWAP_NTOH); 572 573 TI_UNLOCK(sc); 574 if (first_pass) { 575 copyout(&tmparray2[segresid], ptr, 576 segsize - segresid); 577 first_pass = 0; 578 } else 579 copyout(tmparray2, ptr, segsize); 580 TI_LOCK(sc); 581 } else { 582 if (first_pass) { 583 584 ti_bcopy_swap(tmparray, tmparray2, 585 segsize, TI_SWAP_NTOH); 586 TI_UNLOCK(sc); 587 bcopy(&tmparray2[segresid], ptr, 588 segsize - segresid); 589 TI_LOCK(sc); 590 first_pass = 0; 591 } else 592 ti_bcopy_swap(tmparray, ptr, segsize, 593 TI_SWAP_NTOH); 594 } 595 596 } else { 597 if (useraddr) { 598 TI_UNLOCK(sc); 599 copyin(ptr, tmparray2, segsize); 600 TI_LOCK(sc); 601 ti_bcopy_swap(tmparray2, tmparray, segsize, 602 TI_SWAP_HTON); 603 } else 604 ti_bcopy_swap(ptr, tmparray, segsize, 605 TI_SWAP_HTON); 606 607 bus_space_write_region_4(sc->ti_btag, 608 sc->ti_bhandle, ti_offset, 609 (uint32_t *)tmparray, 610 segsize >> 2); 611 } 612 segptr += segsize; 613 ptr += segsize; 614 cnt -= segsize; 615 } 616 617 /* 618 * Handle leftover, non-word-aligned bytes. 619 */ 620 if (resid != 0) { 621 uint32_t tmpval, tmpval2; 622 bus_size_t ti_offset; 623 624 /* 625 * Set the segment pointer. 626 */ 627 CSR_WRITE_4(sc, TI_WINBASE, (segptr & ~(TI_WINLEN - 1))); 628 629 ti_offset = TI_WINDOW + (segptr & (TI_WINLEN - 1)); 630 631 /* 632 * First, grab whatever is in our source/destination. 633 * We'll obviously need this for reads, but also for 634 * writes, since we'll be doing read/modify/write. 635 */ 636 bus_space_read_region_4(sc->ti_btag, sc->ti_bhandle, 637 ti_offset, &tmpval, 1); 638 639 /* 640 * Next, translate this from little-endian to big-endian 641 * (at least on i386 boxes). 642 */ 643 tmpval2 = ntohl(tmpval); 644 645 if (readdata) { 646 /* 647 * If we're reading, just copy the leftover number 648 * of bytes from the host byte order buffer to 649 * the user's buffer. 650 */ 651 if (useraddr) { 652 TI_UNLOCK(sc); 653 copyout(&tmpval2, ptr, resid); 654 TI_LOCK(sc); 655 } else 656 bcopy(&tmpval2, ptr, resid); 657 } else { 658 /* 659 * If we're writing, first copy the bytes to be 660 * written into the network byte order buffer, 661 * leaving the rest of the buffer with whatever was 662 * originally in there. Then, swap the bytes 663 * around into host order and write them out. 664 * 665 * XXX KDM the read side of this has been verified 666 * to work, but the write side of it has not been 667 * verified. So user beware. 668 */ 669 if (useraddr) { 670 TI_UNLOCK(sc); 671 copyin(ptr, &tmpval2, resid); 672 TI_LOCK(sc); 673 } else 674 bcopy(ptr, &tmpval2, resid); 675 676 tmpval = htonl(tmpval2); 677 678 bus_space_write_region_4(sc->ti_btag, sc->ti_bhandle, 679 ti_offset, &tmpval, 1); 680 } 681 } 682 683 CSR_WRITE_4(sc, TI_WINBASE, origwin); 684 685 return (0); 686} 687 688static int 689ti_copy_scratch(struct ti_softc *sc, uint32_t tigon_addr, uint32_t len, 690 caddr_t buf, int useraddr, int readdata, int cpu) 691{ 692 uint32_t segptr; 693 int cnt; 694 uint32_t tmpval, tmpval2; 695 caddr_t ptr; 696 697 TI_LOCK_ASSERT(sc); 698 699 /* 700 * At the moment, we don't handle non-aligned cases, we just bail. 701 * If this proves to be a problem, it will be fixed. 702 */ 703 if (tigon_addr & 0x3) { 704 device_printf(sc->ti_dev, "%s: tigon address %#x " 705 "isn't word-aligned\n", __func__, tigon_addr); 706 return (EINVAL); 707 } 708 709 if (len & 0x3) { 710 device_printf(sc->ti_dev, "%s: transfer length %d " 711 "isn't word-aligned\n", __func__, len); 712 return (EINVAL); 713 } 714 715 segptr = tigon_addr; 716 cnt = len; 717 ptr = buf; 718 719 while (cnt) { 720 CSR_WRITE_4(sc, CPU_REG(TI_SRAM_ADDR, cpu), segptr); 721 722 if (readdata) { 723 tmpval2 = CSR_READ_4(sc, CPU_REG(TI_SRAM_DATA, cpu)); 724 725 tmpval = ntohl(tmpval2); 726 727 /* 728 * Note: I've used this debugging interface 729 * extensively with Alteon's 12.3.15 firmware, 730 * compiled with GCC 2.7.2.1 and binutils 2.9.1. 731 * 732 * When you compile the firmware without 733 * optimization, which is necessary sometimes in 734 * order to properly step through it, you sometimes 735 * read out a bogus value of 0xc0017c instead of 736 * whatever was supposed to be in that scratchpad 737 * location. That value is on the stack somewhere, 738 * but I've never been able to figure out what was 739 * causing the problem. 740 * 741 * The address seems to pop up in random places, 742 * often not in the same place on two subsequent 743 * reads. 744 * 745 * In any case, the underlying data doesn't seem 746 * to be affected, just the value read out. 747 * 748 * KDM, 3/7/2000 749 */ 750 751 if (tmpval2 == 0xc0017c) 752 device_printf(sc->ti_dev, "found 0xc0017c at " 753 "%#x (tmpval2)\n", segptr); 754 755 if (tmpval == 0xc0017c) 756 device_printf(sc->ti_dev, "found 0xc0017c at " 757 "%#x (tmpval)\n", segptr); 758 759 if (useraddr) 760 copyout(&tmpval, ptr, 4); 761 else 762 bcopy(&tmpval, ptr, 4); 763 } else { 764 if (useraddr) 765 copyin(ptr, &tmpval2, 4); 766 else 767 bcopy(ptr, &tmpval2, 4); 768 769 tmpval = htonl(tmpval2); 770 771 CSR_WRITE_4(sc, CPU_REG(TI_SRAM_DATA, cpu), tmpval); 772 } 773 774 cnt -= 4; 775 segptr += 4; 776 ptr += 4; 777 } 778 779 return (0); 780} 781 782static int 783ti_bcopy_swap(const void *src, void *dst, size_t len, ti_swap_type swap_type) 784{ 785 const uint8_t *tmpsrc; 786 uint8_t *tmpdst; 787 size_t tmplen; 788 789 if (len & 0x3) { 790 printf("ti_bcopy_swap: length %zd isn't 32-bit aligned\n", 791 len); 792 return (-1); 793 } 794 795 tmpsrc = src; 796 tmpdst = dst; 797 tmplen = len; 798 799 while (tmplen) { 800 if (swap_type == TI_SWAP_NTOH) 801 *(uint32_t *)tmpdst = 802 ntohl(*(const uint32_t *)tmpsrc); 803 else 804 *(uint32_t *)tmpdst = 805 htonl(*(const uint32_t *)tmpsrc); 806 807 tmpsrc += 4; 808 tmpdst += 4; 809 tmplen -= 4; 810 } 811 812 return (0); 813} 814 815/* 816 * Load firmware image into the NIC. Check that the firmware revision 817 * is acceptable and see if we want the firmware for the Tigon 1 or 818 * Tigon 2. 819 */ 820static void 821ti_loadfw(struct ti_softc *sc) 822{ 823 824 TI_LOCK_ASSERT(sc); 825 826 switch (sc->ti_hwrev) { 827 case TI_HWREV_TIGON: 828 if (tigonFwReleaseMajor != TI_FIRMWARE_MAJOR || 829 tigonFwReleaseMinor != TI_FIRMWARE_MINOR || 830 tigonFwReleaseFix != TI_FIRMWARE_FIX) { 831 device_printf(sc->ti_dev, "firmware revision mismatch; " 832 "want %d.%d.%d, got %d.%d.%d\n", 833 TI_FIRMWARE_MAJOR, TI_FIRMWARE_MINOR, 834 TI_FIRMWARE_FIX, tigonFwReleaseMajor, 835 tigonFwReleaseMinor, tigonFwReleaseFix); 836 return; 837 } 838 ti_mem_write(sc, tigonFwTextAddr, tigonFwTextLen, tigonFwText); 839 ti_mem_write(sc, tigonFwDataAddr, tigonFwDataLen, tigonFwData); 840 ti_mem_write(sc, tigonFwRodataAddr, tigonFwRodataLen, 841 tigonFwRodata); 842 ti_mem_zero(sc, tigonFwBssAddr, tigonFwBssLen); 843 ti_mem_zero(sc, tigonFwSbssAddr, tigonFwSbssLen); 844 CSR_WRITE_4(sc, TI_CPU_PROGRAM_COUNTER, tigonFwStartAddr); 845 break; 846 case TI_HWREV_TIGON_II: 847 if (tigon2FwReleaseMajor != TI_FIRMWARE_MAJOR || 848 tigon2FwReleaseMinor != TI_FIRMWARE_MINOR || 849 tigon2FwReleaseFix != TI_FIRMWARE_FIX) { 850 device_printf(sc->ti_dev, "firmware revision mismatch; " 851 "want %d.%d.%d, got %d.%d.%d\n", 852 TI_FIRMWARE_MAJOR, TI_FIRMWARE_MINOR, 853 TI_FIRMWARE_FIX, tigon2FwReleaseMajor, 854 tigon2FwReleaseMinor, tigon2FwReleaseFix); 855 return; 856 } 857 ti_mem_write(sc, tigon2FwTextAddr, tigon2FwTextLen, 858 tigon2FwText); 859 ti_mem_write(sc, tigon2FwDataAddr, tigon2FwDataLen, 860 tigon2FwData); 861 ti_mem_write(sc, tigon2FwRodataAddr, tigon2FwRodataLen, 862 tigon2FwRodata); 863 ti_mem_zero(sc, tigon2FwBssAddr, tigon2FwBssLen); 864 ti_mem_zero(sc, tigon2FwSbssAddr, tigon2FwSbssLen); 865 CSR_WRITE_4(sc, TI_CPU_PROGRAM_COUNTER, tigon2FwStartAddr); 866 break; 867 default: 868 device_printf(sc->ti_dev, 869 "can't load firmware: unknown hardware rev\n"); 870 break; 871 } 872} 873 874/* 875 * Send the NIC a command via the command ring. 876 */ 877static void 878ti_cmd(struct ti_softc *sc, struct ti_cmd_desc *cmd) 879{ 880 int index; 881 882 index = sc->ti_cmd_saved_prodidx; 883 CSR_WRITE_4(sc, TI_GCR_CMDRING + (index * 4), *(uint32_t *)(cmd)); 884 TI_INC(index, TI_CMD_RING_CNT); 885 CSR_WRITE_4(sc, TI_MB_CMDPROD_IDX, index); 886 sc->ti_cmd_saved_prodidx = index; 887} 888 889/* 890 * Send the NIC an extended command. The 'len' parameter specifies the 891 * number of command slots to include after the initial command. 892 */ 893static void 894ti_cmd_ext(struct ti_softc *sc, struct ti_cmd_desc *cmd, caddr_t arg, int len) 895{ 896 int index; 897 int i; 898 899 index = sc->ti_cmd_saved_prodidx; 900 CSR_WRITE_4(sc, TI_GCR_CMDRING + (index * 4), *(uint32_t *)(cmd)); 901 TI_INC(index, TI_CMD_RING_CNT); 902 for (i = 0; i < len; i++) { 903 CSR_WRITE_4(sc, TI_GCR_CMDRING + (index * 4), 904 *(uint32_t *)(&arg[i * 4])); 905 TI_INC(index, TI_CMD_RING_CNT); 906 } 907 CSR_WRITE_4(sc, TI_MB_CMDPROD_IDX, index); 908 sc->ti_cmd_saved_prodidx = index; 909} 910 911/* 912 * Handle events that have triggered interrupts. 913 */ 914static void 915ti_handle_events(struct ti_softc *sc) 916{ 917 struct ti_event_desc *e; 918 919 if (sc->ti_rdata->ti_event_ring == NULL) 920 return; 921 922 while (sc->ti_ev_saved_considx != sc->ti_ev_prodidx.ti_idx) { 923 e = &sc->ti_rdata->ti_event_ring[sc->ti_ev_saved_considx]; 924 switch (TI_EVENT_EVENT(e)) { 925 case TI_EV_LINKSTAT_CHANGED: 926 sc->ti_linkstat = TI_EVENT_CODE(e); 927 if (sc->ti_linkstat == TI_EV_CODE_LINK_UP) 928 device_printf(sc->ti_dev, "10/100 link up\n"); 929 else if (sc->ti_linkstat == TI_EV_CODE_GIG_LINK_UP) 930 device_printf(sc->ti_dev, "gigabit link up\n"); 931 else if (sc->ti_linkstat == TI_EV_CODE_LINK_DOWN) 932 device_printf(sc->ti_dev, "link down\n"); 933 break; 934 case TI_EV_ERROR: 935 if (TI_EVENT_CODE(e) == TI_EV_CODE_ERR_INVAL_CMD) 936 device_printf(sc->ti_dev, "invalid command\n"); 937 else if (TI_EVENT_CODE(e) == TI_EV_CODE_ERR_UNIMP_CMD) 938 device_printf(sc->ti_dev, "unknown command\n"); 939 else if (TI_EVENT_CODE(e) == TI_EV_CODE_ERR_BADCFG) 940 device_printf(sc->ti_dev, "bad config data\n"); 941 break; 942 case TI_EV_FIRMWARE_UP: 943 ti_init2(sc); 944 break; 945 case TI_EV_STATS_UPDATED: 946 ti_stats_update(sc); 947 break; 948 case TI_EV_RESET_JUMBO_RING: 949 case TI_EV_MCAST_UPDATED: 950 /* Who cares. */ 951 break; 952 default: 953 device_printf(sc->ti_dev, "unknown event: %d\n", 954 TI_EVENT_EVENT(e)); 955 break; 956 } 957 /* Advance the consumer index. */ 958 TI_INC(sc->ti_ev_saved_considx, TI_EVENT_RING_CNT); 959 CSR_WRITE_4(sc, TI_GCR_EVENTCONS_IDX, sc->ti_ev_saved_considx); 960 } 961} 962 963static int 964ti_alloc_dmamaps(struct ti_softc *sc) 965{ 966 int i; 967 968 for (i = 0; i < TI_TX_RING_CNT; i++) { 969 sc->ti_cdata.ti_txdesc[i].tx_m = NULL; 970 sc->ti_cdata.ti_txdesc[i].tx_dmamap = 0; 971 if (bus_dmamap_create(sc->ti_mbuftx_dmat, 0, 972 &sc->ti_cdata.ti_txdesc[i].tx_dmamap)) 973 return (ENOBUFS); 974 } 975 for (i = 0; i < TI_STD_RX_RING_CNT; i++) { 976 if (bus_dmamap_create(sc->ti_mbufrx_dmat, 0, 977 &sc->ti_cdata.ti_rx_std_maps[i])) 978 return (ENOBUFS); 979 } 980 981 for (i = 0; i < TI_JUMBO_RX_RING_CNT; i++) { 982 if (bus_dmamap_create(sc->ti_jumbo_dmat, 0, 983 &sc->ti_cdata.ti_rx_jumbo_maps[i])) 984 return (ENOBUFS); 985 } 986 for (i = 0; i < TI_MINI_RX_RING_CNT; i++) { 987 if (bus_dmamap_create(sc->ti_mbufrx_dmat, 0, 988 &sc->ti_cdata.ti_rx_mini_maps[i])) 989 return (ENOBUFS); 990 } 991 992 return (0); 993} 994 995static void 996ti_free_dmamaps(struct ti_softc *sc) 997{ 998 int i; 999 1000 if (sc->ti_mbuftx_dmat) 1001 for (i = 0; i < TI_TX_RING_CNT; i++) 1002 if (sc->ti_cdata.ti_txdesc[i].tx_dmamap) { 1003 bus_dmamap_destroy(sc->ti_mbuftx_dmat, 1004 sc->ti_cdata.ti_txdesc[i].tx_dmamap); 1005 sc->ti_cdata.ti_txdesc[i].tx_dmamap = 0; 1006 } 1007 1008 if (sc->ti_mbufrx_dmat) 1009 for (i = 0; i < TI_STD_RX_RING_CNT; i++) 1010 if (sc->ti_cdata.ti_rx_std_maps[i]) { 1011 bus_dmamap_destroy(sc->ti_mbufrx_dmat, 1012 sc->ti_cdata.ti_rx_std_maps[i]); 1013 sc->ti_cdata.ti_rx_std_maps[i] = 0; 1014 } 1015 1016 if (sc->ti_jumbo_dmat) 1017 for (i = 0; i < TI_JUMBO_RX_RING_CNT; i++) 1018 if (sc->ti_cdata.ti_rx_jumbo_maps[i]) { 1019 bus_dmamap_destroy(sc->ti_jumbo_dmat, 1020 sc->ti_cdata.ti_rx_jumbo_maps[i]); 1021 sc->ti_cdata.ti_rx_jumbo_maps[i] = 0; 1022 } 1023 if (sc->ti_mbufrx_dmat) 1024 for (i = 0; i < TI_MINI_RX_RING_CNT; i++) 1025 if (sc->ti_cdata.ti_rx_mini_maps[i]) { 1026 bus_dmamap_destroy(sc->ti_mbufrx_dmat, 1027 sc->ti_cdata.ti_rx_mini_maps[i]); 1028 sc->ti_cdata.ti_rx_mini_maps[i] = 0; 1029 } 1030} 1031 1032#ifdef TI_PRIVATE_JUMBOS 1033 1034/* 1035 * Memory management for the jumbo receive ring is a pain in the 1036 * butt. We need to allocate at least 9018 bytes of space per frame, 1037 * _and_ it has to be contiguous (unless you use the extended 1038 * jumbo descriptor format). Using malloc() all the time won't 1039 * work: malloc() allocates memory in powers of two, which means we 1040 * would end up wasting a considerable amount of space by allocating 1041 * 9K chunks. We don't have a jumbo mbuf cluster pool. Thus, we have 1042 * to do our own memory management. 1043 * 1044 * The driver needs to allocate a contiguous chunk of memory at boot 1045 * time. We then chop this up ourselves into 9K pieces and use them 1046 * as external mbuf storage. 1047 * 1048 * One issue here is how much memory to allocate. The jumbo ring has 1049 * 256 slots in it, but at 9K per slot than can consume over 2MB of 1050 * RAM. This is a bit much, especially considering we also need 1051 * RAM for the standard ring and mini ring (on the Tigon 2). To 1052 * save space, we only actually allocate enough memory for 64 slots 1053 * by default, which works out to between 500 and 600K. This can 1054 * be tuned by changing a #define in if_tireg.h. 1055 */ 1056 1057static int 1058ti_alloc_jumbo_mem(struct ti_softc *sc) 1059{ 1060 struct ti_jpool_entry *entry; 1061 caddr_t ptr; 1062 int i; 1063 1064 /* 1065 * Grab a big chunk o' storage. Since we are chopping this pool up 1066 * into ~9k chunks, there doesn't appear to be a need to use page 1067 * alignment. 1068 */ 1069 if (bus_dma_tag_create(sc->ti_parent_dmat, /* parent */ 1070 1, 0, /* algnmnt, boundary */ 1071 BUS_SPACE_MAXADDR, /* lowaddr */ 1072 BUS_SPACE_MAXADDR, /* highaddr */ 1073 NULL, NULL, /* filter, filterarg */ 1074 TI_JMEM, /* maxsize */ 1075 1, /* nsegments */ 1076 TI_JMEM, /* maxsegsize */ 1077 0, /* flags */ 1078 NULL, NULL, /* lockfunc, lockarg */ 1079 &sc->ti_jumbo_dmat) != 0) { 1080 device_printf(sc->ti_dev, "Failed to allocate jumbo dmat\n"); 1081 return (ENOBUFS); 1082 } 1083 1084 if (bus_dmamem_alloc(sc->ti_jumbo_dmat, 1085 (void**)&sc->ti_cdata.ti_jumbo_buf, 1086 BUS_DMA_NOWAIT | BUS_DMA_COHERENT, 1087 &sc->ti_jumbo_dmamap) != 0) { 1088 device_printf(sc->ti_dev, "Failed to allocate jumbo memory\n"); 1089 return (ENOBUFS); 1090 } 1091 1092 SLIST_INIT(&sc->ti_jfree_listhead); 1093 SLIST_INIT(&sc->ti_jinuse_listhead); 1094 1095 /* 1096 * Now divide it up into 9K pieces and save the addresses 1097 * in an array. 1098 */ 1099 ptr = sc->ti_cdata.ti_jumbo_buf; 1100 for (i = 0; i < TI_JSLOTS; i++) { 1101 sc->ti_cdata.ti_jslots[i] = ptr; 1102 ptr += TI_JLEN; 1103 entry = malloc(sizeof(struct ti_jpool_entry), 1104 M_DEVBUF, M_NOWAIT); 1105 if (entry == NULL) { 1106 device_printf(sc->ti_dev, "no memory for jumbo " 1107 "buffer queue!\n"); 1108 return (ENOBUFS); 1109 } 1110 entry->slot = i; 1111 SLIST_INSERT_HEAD(&sc->ti_jfree_listhead, entry, jpool_entries); 1112 } 1113 1114 return (0); 1115} 1116 1117/* 1118 * Allocate a jumbo buffer. 1119 */ 1120static void *ti_jalloc(struct ti_softc *sc) 1121{ 1122 struct ti_jpool_entry *entry; 1123 1124 entry = SLIST_FIRST(&sc->ti_jfree_listhead); 1125 1126 if (entry == NULL) { 1127 device_printf(sc->ti_dev, "no free jumbo buffers\n"); 1128 return (NULL); 1129 } 1130 1131 SLIST_REMOVE_HEAD(&sc->ti_jfree_listhead, jpool_entries); 1132 SLIST_INSERT_HEAD(&sc->ti_jinuse_listhead, entry, jpool_entries); 1133 return (sc->ti_cdata.ti_jslots[entry->slot]); 1134} 1135 1136/* 1137 * Release a jumbo buffer. 1138 */ 1139static void 1140ti_jfree(void *buf, void *args) 1141{ 1142 struct ti_softc *sc; 1143 int i; 1144 struct ti_jpool_entry *entry; 1145 1146 /* Extract the softc struct pointer. */ 1147 sc = (struct ti_softc *)args; 1148 1149 if (sc == NULL) 1150 panic("ti_jfree: didn't get softc pointer!"); 1151 1152 /* calculate the slot this buffer belongs to */ 1153 i = ((vm_offset_t)buf 1154 - (vm_offset_t)sc->ti_cdata.ti_jumbo_buf) / TI_JLEN; 1155 1156 if ((i < 0) || (i >= TI_JSLOTS)) 1157 panic("ti_jfree: asked to free buffer that we don't manage!"); 1158 1159 entry = SLIST_FIRST(&sc->ti_jinuse_listhead); 1160 if (entry == NULL) 1161 panic("ti_jfree: buffer not in use!"); 1162 entry->slot = i; 1163 SLIST_REMOVE_HEAD(&sc->ti_jinuse_listhead, jpool_entries); 1164 SLIST_INSERT_HEAD(&sc->ti_jfree_listhead, entry, jpool_entries); 1165} 1166 1167#else 1168 1169static int 1170ti_alloc_jumbo_mem(struct ti_softc *sc) 1171{ 1172 1173 /* 1174 * The VM system will take care of providing aligned pages. Alignment 1175 * is set to 1 here so that busdma resources won't be wasted. 1176 */ 1177 if (bus_dma_tag_create(sc->ti_parent_dmat, /* parent */ 1178 1, 0, /* algnmnt, boundary */ 1179 BUS_SPACE_MAXADDR, /* lowaddr */ 1180 BUS_SPACE_MAXADDR, /* highaddr */ 1181 NULL, NULL, /* filter, filterarg */ 1182 PAGE_SIZE * 4 /*XXX*/, /* maxsize */ 1183 4, /* nsegments */ 1184 PAGE_SIZE, /* maxsegsize */ 1185 0, /* flags */ 1186 NULL, NULL, /* lockfunc, lockarg */ 1187 &sc->ti_jumbo_dmat) != 0) { 1188 device_printf(sc->ti_dev, "Failed to allocate jumbo dmat\n"); 1189 return (ENOBUFS); 1190 } 1191 1192 return (0); 1193} 1194 1195#endif /* TI_PRIVATE_JUMBOS */ 1196 1197/* 1198 * Intialize a standard receive ring descriptor. 1199 */ 1200static int 1201ti_newbuf_std(struct ti_softc *sc, int i, struct mbuf *m) 1202{ 1203 bus_dmamap_t map; 1204 bus_dma_segment_t segs; 1205 struct mbuf *m_new = NULL; 1206 struct ti_rx_desc *r; 1207 int nsegs; 1208 1209 nsegs = 0; 1210 if (m == NULL) { 1211 MGETHDR(m_new, M_DONTWAIT, MT_DATA); 1212 if (m_new == NULL) 1213 return (ENOBUFS); 1214 1215 MCLGET(m_new, M_DONTWAIT); 1216 if (!(m_new->m_flags & M_EXT)) { 1217 m_freem(m_new); 1218 return (ENOBUFS); 1219 } 1220 m_new->m_len = m_new->m_pkthdr.len = MCLBYTES; 1221 } else { 1222 m_new = m; 1223 m_new->m_len = m_new->m_pkthdr.len = MCLBYTES; 1224 m_new->m_data = m_new->m_ext.ext_buf; 1225 } 1226 1227 m_adj(m_new, ETHER_ALIGN); 1228 sc->ti_cdata.ti_rx_std_chain[i] = m_new; 1229 r = &sc->ti_rdata->ti_rx_std_ring[i]; 1230 map = sc->ti_cdata.ti_rx_std_maps[i]; 1231 if (bus_dmamap_load_mbuf_sg(sc->ti_mbufrx_dmat, map, m_new, &segs, 1232 &nsegs, 0)) 1233 return (ENOBUFS); 1234 if (nsegs != 1) 1235 return (ENOBUFS); 1236 ti_hostaddr64(&r->ti_addr, segs.ds_addr); 1237 r->ti_len = segs.ds_len; 1238 r->ti_type = TI_BDTYPE_RECV_BD; 1239 r->ti_flags = 0; 1240 if (sc->ti_ifp->if_hwassist) 1241 r->ti_flags |= TI_BDFLAG_TCP_UDP_CKSUM | TI_BDFLAG_IP_CKSUM; 1242 r->ti_idx = i; 1243 1244 bus_dmamap_sync(sc->ti_mbufrx_dmat, map, BUS_DMASYNC_PREREAD); 1245 return (0); 1246} 1247 1248/* 1249 * Intialize a mini receive ring descriptor. This only applies to 1250 * the Tigon 2. 1251 */ 1252static int 1253ti_newbuf_mini(struct ti_softc *sc, int i, struct mbuf *m) 1254{ 1255 bus_dma_segment_t segs; 1256 bus_dmamap_t map; 1257 struct mbuf *m_new = NULL; 1258 struct ti_rx_desc *r; 1259 int nsegs; 1260 1261 nsegs = 0; 1262 if (m == NULL) { 1263 MGETHDR(m_new, M_DONTWAIT, MT_DATA); 1264 if (m_new == NULL) { 1265 return (ENOBUFS); 1266 } 1267 m_new->m_len = m_new->m_pkthdr.len = MHLEN; 1268 } else { 1269 m_new = m; 1270 m_new->m_data = m_new->m_pktdat; 1271 m_new->m_len = m_new->m_pkthdr.len = MHLEN; 1272 } 1273 1274 m_adj(m_new, ETHER_ALIGN); 1275 r = &sc->ti_rdata->ti_rx_mini_ring[i]; 1276 sc->ti_cdata.ti_rx_mini_chain[i] = m_new; 1277 map = sc->ti_cdata.ti_rx_mini_maps[i]; 1278 if (bus_dmamap_load_mbuf_sg(sc->ti_mbufrx_dmat, map, m_new, &segs, 1279 &nsegs, 0)) 1280 return (ENOBUFS); 1281 if (nsegs != 1) 1282 return (ENOBUFS); 1283 ti_hostaddr64(&r->ti_addr, segs.ds_addr); 1284 r->ti_len = segs.ds_len; 1285 r->ti_type = TI_BDTYPE_RECV_BD; 1286 r->ti_flags = TI_BDFLAG_MINI_RING; 1287 if (sc->ti_ifp->if_hwassist) 1288 r->ti_flags |= TI_BDFLAG_TCP_UDP_CKSUM | TI_BDFLAG_IP_CKSUM; 1289 r->ti_idx = i; 1290 1291 bus_dmamap_sync(sc->ti_mbufrx_dmat, map, BUS_DMASYNC_PREREAD); 1292 return (0); 1293} 1294 1295#ifdef TI_PRIVATE_JUMBOS 1296 1297/* 1298 * Initialize a jumbo receive ring descriptor. This allocates 1299 * a jumbo buffer from the pool managed internally by the driver. 1300 */ 1301static int 1302ti_newbuf_jumbo(struct ti_softc *sc, int i, struct mbuf *m) 1303{ 1304 bus_dmamap_t map; 1305 struct mbuf *m_new = NULL; 1306 struct ti_rx_desc *r; 1307 int nsegs; 1308 bus_dma_segment_t segs; 1309 1310 if (m == NULL) { 1311 caddr_t *buf = NULL; 1312 1313 /* Allocate the mbuf. */ 1314 MGETHDR(m_new, M_DONTWAIT, MT_DATA); 1315 if (m_new == NULL) { 1316 return (ENOBUFS); 1317 } 1318 1319 /* Allocate the jumbo buffer */ 1320 buf = ti_jalloc(sc); 1321 if (buf == NULL) { 1322 m_freem(m_new); 1323 device_printf(sc->ti_dev, "jumbo allocation failed " 1324 "-- packet dropped!\n"); 1325 return (ENOBUFS); 1326 } 1327 1328 /* Attach the buffer to the mbuf. */ 1329 m_new->m_data = (void *) buf; 1330 m_new->m_len = m_new->m_pkthdr.len = TI_JUMBO_FRAMELEN; 1331 MEXTADD(m_new, buf, TI_JUMBO_FRAMELEN, ti_jfree, buf, 1332 (struct ti_softc *)sc, 0, EXT_NET_DRV); 1333 } else { 1334 m_new = m; 1335 m_new->m_data = m_new->m_ext.ext_buf; 1336 m_new->m_ext.ext_size = TI_JUMBO_FRAMELEN; 1337 } 1338 1339 m_adj(m_new, ETHER_ALIGN); 1340 /* Set up the descriptor. */ 1341 r = &sc->ti_rdata->ti_rx_jumbo_ring[i]; 1342 sc->ti_cdata.ti_rx_jumbo_chain[i] = m_new; 1343 map = sc->ti_cdata.ti_rx_jumbo_maps[i]; 1344 if (bus_dmamap_load_mbuf_sg(sc->ti_jumbo_dmat, map, m_new, &segs, 1345 &nsegs, 0)) 1346 return (ENOBUFS); 1347 if (nsegs != 1) 1348 return (ENOBUFS); 1349 ti_hostaddr64(&r->ti_addr, segs.ds_addr); 1350 r->ti_len = segs.ds_len; 1351 r->ti_type = TI_BDTYPE_RECV_JUMBO_BD; 1352 r->ti_flags = TI_BDFLAG_JUMBO_RING; 1353 if (sc->ti_ifp->if_hwassist) 1354 r->ti_flags |= TI_BDFLAG_TCP_UDP_CKSUM | TI_BDFLAG_IP_CKSUM; 1355 r->ti_idx = i; 1356 1357 bus_dmamap_sync(sc->ti_jumbo_dmat, map, BUS_DMASYNC_PREREAD); 1358 return (0); 1359} 1360 1361#else 1362 1363#if (PAGE_SIZE == 4096) 1364#define NPAYLOAD 2 1365#else 1366#define NPAYLOAD 1 1367#endif 1368 1369#define TCP_HDR_LEN (52 + sizeof(struct ether_header)) 1370#define UDP_HDR_LEN (28 + sizeof(struct ether_header)) 1371#define NFS_HDR_LEN (UDP_HDR_LEN) 1372static int HDR_LEN = TCP_HDR_LEN; 1373 1374/* 1375 * Initialize a jumbo receive ring descriptor. This allocates 1376 * a jumbo buffer from the pool managed internally by the driver. 1377 */ 1378static int 1379ti_newbuf_jumbo(struct ti_softc *sc, int idx, struct mbuf *m_old) 1380{ 1381 bus_dmamap_t map; 1382 struct mbuf *cur, *m_new = NULL; 1383 struct mbuf *m[3] = {NULL, NULL, NULL}; 1384 struct ti_rx_desc_ext *r; 1385 vm_page_t frame; 1386 static int color; 1387 /* 1 extra buf to make nobufs easy*/ 1388 struct sf_buf *sf[3] = {NULL, NULL, NULL}; 1389 int i; 1390 bus_dma_segment_t segs[4]; 1391 int nsegs; 1392 1393 if (m_old != NULL) { 1394 m_new = m_old; 1395 cur = m_old->m_next; 1396 for (i = 0; i <= NPAYLOAD; i++){ 1397 m[i] = cur; 1398 cur = cur->m_next; 1399 } 1400 } else { 1401 /* Allocate the mbufs. */ 1402 MGETHDR(m_new, M_DONTWAIT, MT_DATA); 1403 if (m_new == NULL) { 1404 device_printf(sc->ti_dev, "mbuf allocation failed " 1405 "-- packet dropped!\n"); 1406 goto nobufs; 1407 } 1408 MGET(m[NPAYLOAD], M_DONTWAIT, MT_DATA); 1409 if (m[NPAYLOAD] == NULL) { 1410 device_printf(sc->ti_dev, "cluster mbuf allocation " 1411 "failed -- packet dropped!\n"); 1412 goto nobufs; 1413 } 1414 MCLGET(m[NPAYLOAD], M_DONTWAIT); 1415 if ((m[NPAYLOAD]->m_flags & M_EXT) == 0) { 1416 device_printf(sc->ti_dev, "mbuf allocation failed " 1417 "-- packet dropped!\n"); 1418 goto nobufs; 1419 } 1420 m[NPAYLOAD]->m_len = MCLBYTES; 1421 1422 for (i = 0; i < NPAYLOAD; i++){ 1423 MGET(m[i], M_DONTWAIT, MT_DATA); 1424 if (m[i] == NULL) { 1425 device_printf(sc->ti_dev, "mbuf allocation " 1426 "failed -- packet dropped!\n"); 1427 goto nobufs; 1428 } 1429 frame = vm_page_alloc(NULL, color++, 1430 VM_ALLOC_INTERRUPT | VM_ALLOC_NOOBJ | 1431 VM_ALLOC_WIRED); 1432 if (frame == NULL) { 1433 device_printf(sc->ti_dev, "buffer allocation " 1434 "failed -- packet dropped!\n"); 1435 printf(" index %d page %d\n", idx, i); 1436 goto nobufs; 1437 } 1438 sf[i] = sf_buf_alloc(frame, SFB_NOWAIT); 1439 if (sf[i] == NULL) { 1440 vm_page_unwire(frame, 0); 1441 vm_page_free(frame); 1442 device_printf(sc->ti_dev, "buffer allocation " 1443 "failed -- packet dropped!\n"); 1444 printf(" index %d page %d\n", idx, i); 1445 goto nobufs; 1446 } 1447 } 1448 for (i = 0; i < NPAYLOAD; i++){ 1449 /* Attach the buffer to the mbuf. */ 1450 m[i]->m_data = (void *)sf_buf_kva(sf[i]); 1451 m[i]->m_len = PAGE_SIZE; 1452 MEXTADD(m[i], sf_buf_kva(sf[i]), PAGE_SIZE, 1453 sf_buf_mext, (void*)sf_buf_kva(sf[i]), sf[i], 1454 0, EXT_DISPOSABLE); 1455 m[i]->m_next = m[i+1]; 1456 } 1457 /* link the buffers to the header */ 1458 m_new->m_next = m[0]; 1459 m_new->m_data += ETHER_ALIGN; 1460 if (sc->ti_hdrsplit) 1461 m_new->m_len = MHLEN - ETHER_ALIGN; 1462 else 1463 m_new->m_len = HDR_LEN; 1464 m_new->m_pkthdr.len = NPAYLOAD * PAGE_SIZE + m_new->m_len; 1465 } 1466 1467 /* Set up the descriptor. */ 1468 r = &sc->ti_rdata->ti_rx_jumbo_ring[idx]; 1469 sc->ti_cdata.ti_rx_jumbo_chain[idx] = m_new; 1470 map = sc->ti_cdata.ti_rx_jumbo_maps[i]; 1471 if (bus_dmamap_load_mbuf_sg(sc->ti_jumbo_dmat, map, m_new, segs, 1472 &nsegs, 0)) 1473 return (ENOBUFS); 1474 if ((nsegs < 1) || (nsegs > 4)) 1475 return (ENOBUFS); 1476 ti_hostaddr64(&r->ti_addr0, segs[0].ds_addr); 1477 r->ti_len0 = m_new->m_len; 1478 1479 ti_hostaddr64(&r->ti_addr1, segs[1].ds_addr); 1480 r->ti_len1 = PAGE_SIZE; 1481 1482 ti_hostaddr64(&r->ti_addr2, segs[2].ds_addr); 1483 r->ti_len2 = m[1]->m_ext.ext_size; /* could be PAGE_SIZE or MCLBYTES */ 1484 1485 if (PAGE_SIZE == 4096) { 1486 ti_hostaddr64(&r->ti_addr3, segs[3].ds_addr); 1487 r->ti_len3 = MCLBYTES; 1488 } else { 1489 r->ti_len3 = 0; 1490 } 1491 r->ti_type = TI_BDTYPE_RECV_JUMBO_BD; 1492 1493 r->ti_flags = TI_BDFLAG_JUMBO_RING|TI_RCB_FLAG_USE_EXT_RX_BD; 1494 1495 if (sc->ti_ifp->if_hwassist) 1496 r->ti_flags |= TI_BDFLAG_TCP_UDP_CKSUM|TI_BDFLAG_IP_CKSUM; 1497 1498 r->ti_idx = idx; 1499 1500 bus_dmamap_sync(sc->ti_jumbo_dmat, map, BUS_DMASYNC_PREREAD); 1501 return (0); 1502 1503nobufs: 1504 1505 /* 1506 * Warning! : 1507 * This can only be called before the mbufs are strung together. 1508 * If the mbufs are strung together, m_freem() will free the chain, 1509 * so that the later mbufs will be freed multiple times. 1510 */ 1511 if (m_new) 1512 m_freem(m_new); 1513 1514 for (i = 0; i < 3; i++) { 1515 if (m[i]) 1516 m_freem(m[i]); 1517 if (sf[i]) 1518 sf_buf_mext((void *)sf_buf_kva(sf[i]), sf[i]); 1519 } 1520 return (ENOBUFS); 1521} 1522#endif 1523 1524/* 1525 * The standard receive ring has 512 entries in it. At 2K per mbuf cluster, 1526 * that's 1MB or memory, which is a lot. For now, we fill only the first 1527 * 256 ring entries and hope that our CPU is fast enough to keep up with 1528 * the NIC. 1529 */ 1530static int 1531ti_init_rx_ring_std(struct ti_softc *sc) 1532{ 1533 int i; 1534 struct ti_cmd_desc cmd; 1535 1536 for (i = 0; i < TI_SSLOTS; i++) { 1537 if (ti_newbuf_std(sc, i, NULL) == ENOBUFS) 1538 return (ENOBUFS); 1539 }; 1540 1541 TI_UPDATE_STDPROD(sc, i - 1); 1542 sc->ti_std = i - 1; 1543 1544 return (0); 1545} 1546 1547static void 1548ti_free_rx_ring_std(struct ti_softc *sc) 1549{ 1550 bus_dmamap_t map; 1551 int i; 1552 1553 for (i = 0; i < TI_STD_RX_RING_CNT; i++) { 1554 if (sc->ti_cdata.ti_rx_std_chain[i] != NULL) { 1555 map = sc->ti_cdata.ti_rx_std_maps[i]; 1556 bus_dmamap_sync(sc->ti_mbufrx_dmat, map, 1557 BUS_DMASYNC_POSTREAD); 1558 bus_dmamap_unload(sc->ti_mbufrx_dmat, map); 1559 m_freem(sc->ti_cdata.ti_rx_std_chain[i]); 1560 sc->ti_cdata.ti_rx_std_chain[i] = NULL; 1561 } 1562 bzero((char *)&sc->ti_rdata->ti_rx_std_ring[i], 1563 sizeof(struct ti_rx_desc)); 1564 } 1565} 1566 1567static int 1568ti_init_rx_ring_jumbo(struct ti_softc *sc) 1569{ 1570 struct ti_cmd_desc cmd; 1571 int i; 1572 1573 for (i = 0; i < TI_JUMBO_RX_RING_CNT; i++) { 1574 if (ti_newbuf_jumbo(sc, i, NULL) == ENOBUFS) 1575 return (ENOBUFS); 1576 }; 1577 1578 TI_UPDATE_JUMBOPROD(sc, i - 1); 1579 sc->ti_jumbo = i - 1; 1580 1581 return (0); 1582} 1583 1584static void 1585ti_free_rx_ring_jumbo(struct ti_softc *sc) 1586{ 1587 bus_dmamap_t map; 1588 int i; 1589 1590 for (i = 0; i < TI_JUMBO_RX_RING_CNT; i++) { 1591 if (sc->ti_cdata.ti_rx_jumbo_chain[i] != NULL) { 1592 map = sc->ti_cdata.ti_rx_jumbo_maps[i]; 1593 bus_dmamap_sync(sc->ti_jumbo_dmat, map, 1594 BUS_DMASYNC_POSTREAD); 1595 bus_dmamap_unload(sc->ti_jumbo_dmat, map); 1596 m_freem(sc->ti_cdata.ti_rx_jumbo_chain[i]); 1597 sc->ti_cdata.ti_rx_jumbo_chain[i] = NULL; 1598 } 1599 bzero((char *)&sc->ti_rdata->ti_rx_jumbo_ring[i], 1600 sizeof(struct ti_rx_desc)); 1601 } 1602} 1603 1604static int 1605ti_init_rx_ring_mini(struct ti_softc *sc) 1606{ 1607 int i; 1608 1609 for (i = 0; i < TI_MSLOTS; i++) { 1610 if (ti_newbuf_mini(sc, i, NULL) == ENOBUFS) 1611 return (ENOBUFS); 1612 }; 1613 1614 TI_UPDATE_MINIPROD(sc, i - 1); 1615 sc->ti_mini = i - 1; 1616 1617 return (0); 1618} 1619 1620static void 1621ti_free_rx_ring_mini(struct ti_softc *sc) 1622{ 1623 bus_dmamap_t map; 1624 int i; 1625 1626 for (i = 0; i < TI_MINI_RX_RING_CNT; i++) { 1627 if (sc->ti_cdata.ti_rx_mini_chain[i] != NULL) { 1628 map = sc->ti_cdata.ti_rx_mini_maps[i]; 1629 bus_dmamap_sync(sc->ti_mbufrx_dmat, map, 1630 BUS_DMASYNC_POSTREAD); 1631 bus_dmamap_unload(sc->ti_mbufrx_dmat, map); 1632 m_freem(sc->ti_cdata.ti_rx_mini_chain[i]); 1633 sc->ti_cdata.ti_rx_mini_chain[i] = NULL; 1634 } 1635 bzero((char *)&sc->ti_rdata->ti_rx_mini_ring[i], 1636 sizeof(struct ti_rx_desc)); 1637 } 1638} 1639 1640static void 1641ti_free_tx_ring(struct ti_softc *sc) 1642{ 1643 struct ti_txdesc *txd; 1644 int i; 1645 1646 if (sc->ti_rdata->ti_tx_ring == NULL) 1647 return; 1648 1649 for (i = 0; i < TI_TX_RING_CNT; i++) { 1650 txd = &sc->ti_cdata.ti_txdesc[i]; 1651 if (txd->tx_m != NULL) { 1652 bus_dmamap_sync(sc->ti_mbuftx_dmat, txd->tx_dmamap, 1653 BUS_DMASYNC_POSTWRITE); 1654 bus_dmamap_unload(sc->ti_mbuftx_dmat, txd->tx_dmamap); 1655 m_freem(txd->tx_m); 1656 txd->tx_m = NULL; 1657 } 1658 bzero((char *)&sc->ti_rdata->ti_tx_ring[i], 1659 sizeof(struct ti_tx_desc)); 1660 } 1661} 1662 1663static int 1664ti_init_tx_ring(struct ti_softc *sc) 1665{ 1666 struct ti_txdesc *txd; 1667 int i; 1668 1669 STAILQ_INIT(&sc->ti_cdata.ti_txfreeq); 1670 STAILQ_INIT(&sc->ti_cdata.ti_txbusyq); 1671 for (i = 0; i < TI_TX_RING_CNT; i++) { 1672 txd = &sc->ti_cdata.ti_txdesc[i]; 1673 STAILQ_INSERT_TAIL(&sc->ti_cdata.ti_txfreeq, txd, tx_q); 1674 } 1675 sc->ti_txcnt = 0; 1676 sc->ti_tx_saved_considx = 0; 1677 sc->ti_tx_saved_prodidx = 0; 1678 CSR_WRITE_4(sc, TI_MB_SENDPROD_IDX, 0); 1679 return (0); 1680} 1681 1682/* 1683 * The Tigon 2 firmware has a new way to add/delete multicast addresses, 1684 * but we have to support the old way too so that Tigon 1 cards will 1685 * work. 1686 */ 1687static void 1688ti_add_mcast(struct ti_softc *sc, struct ether_addr *addr) 1689{ 1690 struct ti_cmd_desc cmd; 1691 uint16_t *m; 1692 uint32_t ext[2] = {0, 0}; 1693 1694 m = (uint16_t *)&addr->octet[0]; 1695 1696 switch (sc->ti_hwrev) { 1697 case TI_HWREV_TIGON: 1698 CSR_WRITE_4(sc, TI_GCR_MAR0, htons(m[0])); 1699 CSR_WRITE_4(sc, TI_GCR_MAR1, (htons(m[1]) << 16) | htons(m[2])); 1700 TI_DO_CMD(TI_CMD_ADD_MCAST_ADDR, 0, 0); 1701 break; 1702 case TI_HWREV_TIGON_II: 1703 ext[0] = htons(m[0]); 1704 ext[1] = (htons(m[1]) << 16) | htons(m[2]); 1705 TI_DO_CMD_EXT(TI_CMD_EXT_ADD_MCAST, 0, 0, (caddr_t)&ext, 2); 1706 break; 1707 default: 1708 device_printf(sc->ti_dev, "unknown hwrev\n"); 1709 break; 1710 } 1711} 1712 1713static void 1714ti_del_mcast(struct ti_softc *sc, struct ether_addr *addr) 1715{ 1716 struct ti_cmd_desc cmd; 1717 uint16_t *m; 1718 uint32_t ext[2] = {0, 0}; 1719 1720 m = (uint16_t *)&addr->octet[0]; 1721 1722 switch (sc->ti_hwrev) { 1723 case TI_HWREV_TIGON: 1724 CSR_WRITE_4(sc, TI_GCR_MAR0, htons(m[0])); 1725 CSR_WRITE_4(sc, TI_GCR_MAR1, (htons(m[1]) << 16) | htons(m[2])); 1726 TI_DO_CMD(TI_CMD_DEL_MCAST_ADDR, 0, 0); 1727 break; 1728 case TI_HWREV_TIGON_II: 1729 ext[0] = htons(m[0]); 1730 ext[1] = (htons(m[1]) << 16) | htons(m[2]); 1731 TI_DO_CMD_EXT(TI_CMD_EXT_DEL_MCAST, 0, 0, (caddr_t)&ext, 2); 1732 break; 1733 default: 1734 device_printf(sc->ti_dev, "unknown hwrev\n"); 1735 break; 1736 } 1737} 1738 1739/* 1740 * Configure the Tigon's multicast address filter. 1741 * 1742 * The actual multicast table management is a bit of a pain, thanks to 1743 * slight brain damage on the part of both Alteon and us. With our 1744 * multicast code, we are only alerted when the multicast address table 1745 * changes and at that point we only have the current list of addresses: 1746 * we only know the current state, not the previous state, so we don't 1747 * actually know what addresses were removed or added. The firmware has 1748 * state, but we can't get our grubby mits on it, and there is no 'delete 1749 * all multicast addresses' command. Hence, we have to maintain our own 1750 * state so we know what addresses have been programmed into the NIC at 1751 * any given time. 1752 */ 1753static void 1754ti_setmulti(struct ti_softc *sc) 1755{ 1756 struct ifnet *ifp; 1757 struct ifmultiaddr *ifma; 1758 struct ti_cmd_desc cmd; 1759 struct ti_mc_entry *mc; 1760 uint32_t intrs; 1761 1762 TI_LOCK_ASSERT(sc); 1763 1764 ifp = sc->ti_ifp; 1765 1766 if (ifp->if_flags & IFF_ALLMULTI) { 1767 TI_DO_CMD(TI_CMD_SET_ALLMULTI, TI_CMD_CODE_ALLMULTI_ENB, 0); 1768 return; 1769 } else { 1770 TI_DO_CMD(TI_CMD_SET_ALLMULTI, TI_CMD_CODE_ALLMULTI_DIS, 0); 1771 } 1772 1773 /* Disable interrupts. */ 1774 intrs = CSR_READ_4(sc, TI_MB_HOSTINTR); 1775 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 1); 1776 1777 /* First, zot all the existing filters. */ 1778 while (SLIST_FIRST(&sc->ti_mc_listhead) != NULL) { 1779 mc = SLIST_FIRST(&sc->ti_mc_listhead); 1780 ti_del_mcast(sc, &mc->mc_addr); 1781 SLIST_REMOVE_HEAD(&sc->ti_mc_listhead, mc_entries); 1782 free(mc, M_DEVBUF); 1783 } 1784 1785 /* Now program new ones. */ 1786 if_maddr_rlock(ifp); 1787 TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) { 1788 if (ifma->ifma_addr->sa_family != AF_LINK) 1789 continue; 1790 mc = malloc(sizeof(struct ti_mc_entry), M_DEVBUF, M_NOWAIT); 1791 if (mc == NULL) { 1792 device_printf(sc->ti_dev, 1793 "no memory for mcast filter entry\n"); 1794 continue; 1795 } 1796 bcopy(LLADDR((struct sockaddr_dl *)ifma->ifma_addr), 1797 (char *)&mc->mc_addr, ETHER_ADDR_LEN); 1798 SLIST_INSERT_HEAD(&sc->ti_mc_listhead, mc, mc_entries); 1799 ti_add_mcast(sc, &mc->mc_addr); 1800 } 1801 if_maddr_runlock(ifp); 1802 1803 /* Re-enable interrupts. */ 1804 CSR_WRITE_4(sc, TI_MB_HOSTINTR, intrs); 1805} 1806 1807/* 1808 * Check to see if the BIOS has configured us for a 64 bit slot when 1809 * we aren't actually in one. If we detect this condition, we can work 1810 * around it on the Tigon 2 by setting a bit in the PCI state register, 1811 * but for the Tigon 1 we must give up and abort the interface attach. 1812 */ 1813static int ti_64bitslot_war(struct ti_softc *sc) 1814{ 1815 1816 if (!(CSR_READ_4(sc, TI_PCI_STATE) & TI_PCISTATE_32BIT_BUS)) { 1817 CSR_WRITE_4(sc, 0x600, 0); 1818 CSR_WRITE_4(sc, 0x604, 0); 1819 CSR_WRITE_4(sc, 0x600, 0x5555AAAA); 1820 if (CSR_READ_4(sc, 0x604) == 0x5555AAAA) { 1821 if (sc->ti_hwrev == TI_HWREV_TIGON) 1822 return (EINVAL); 1823 else { 1824 TI_SETBIT(sc, TI_PCI_STATE, 1825 TI_PCISTATE_32BIT_BUS); 1826 return (0); 1827 } 1828 } 1829 } 1830 1831 return (0); 1832} 1833 1834/* 1835 * Do endian, PCI and DMA initialization. Also check the on-board ROM 1836 * self-test results. 1837 */ 1838static int 1839ti_chipinit(struct ti_softc *sc) 1840{ 1841 uint32_t cacheline; 1842 uint32_t pci_writemax = 0; 1843 uint32_t hdrsplit; 1844 1845 /* Initialize link to down state. */ 1846 sc->ti_linkstat = TI_EV_CODE_LINK_DOWN; 1847 1848 if (sc->ti_ifp->if_capenable & IFCAP_HWCSUM) 1849 sc->ti_ifp->if_hwassist = TI_CSUM_FEATURES; 1850 else 1851 sc->ti_ifp->if_hwassist = 0; 1852 1853 /* Set endianness before we access any non-PCI registers. */ 1854#if 0 && BYTE_ORDER == BIG_ENDIAN 1855 CSR_WRITE_4(sc, TI_MISC_HOST_CTL, 1856 TI_MHC_BIGENDIAN_INIT | (TI_MHC_BIGENDIAN_INIT << 24)); 1857#else 1858 CSR_WRITE_4(sc, TI_MISC_HOST_CTL, 1859 TI_MHC_LITTLEENDIAN_INIT | (TI_MHC_LITTLEENDIAN_INIT << 24)); 1860#endif 1861 1862 /* Check the ROM failed bit to see if self-tests passed. */ 1863 if (CSR_READ_4(sc, TI_CPU_STATE) & TI_CPUSTATE_ROMFAIL) { 1864 device_printf(sc->ti_dev, "board self-diagnostics failed!\n"); 1865 return (ENODEV); 1866 } 1867 1868 /* Halt the CPU. */ 1869 TI_SETBIT(sc, TI_CPU_STATE, TI_CPUSTATE_HALT); 1870 1871 /* Figure out the hardware revision. */ 1872 switch (CSR_READ_4(sc, TI_MISC_HOST_CTL) & TI_MHC_CHIP_REV_MASK) { 1873 case TI_REV_TIGON_I: 1874 sc->ti_hwrev = TI_HWREV_TIGON; 1875 break; 1876 case TI_REV_TIGON_II: 1877 sc->ti_hwrev = TI_HWREV_TIGON_II; 1878 break; 1879 default: 1880 device_printf(sc->ti_dev, "unsupported chip revision\n"); 1881 return (ENODEV); 1882 } 1883 1884 /* Do special setup for Tigon 2. */ 1885 if (sc->ti_hwrev == TI_HWREV_TIGON_II) { 1886 TI_SETBIT(sc, TI_CPU_CTL_B, TI_CPUSTATE_HALT); 1887 TI_SETBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_SRAM_BANK_512K); 1888 TI_SETBIT(sc, TI_MISC_CONF, TI_MCR_SRAM_SYNCHRONOUS); 1889 } 1890 1891 /* 1892 * We don't have firmware source for the Tigon 1, so Tigon 1 boards 1893 * can't do header splitting. 1894 */ 1895#ifdef TI_JUMBO_HDRSPLIT 1896 if (sc->ti_hwrev != TI_HWREV_TIGON) 1897 sc->ti_hdrsplit = 1; 1898 else 1899 device_printf(sc->ti_dev, 1900 "can't do header splitting on a Tigon I board\n"); 1901#endif /* TI_JUMBO_HDRSPLIT */ 1902 1903 /* Set up the PCI state register. */ 1904 CSR_WRITE_4(sc, TI_PCI_STATE, TI_PCI_READ_CMD|TI_PCI_WRITE_CMD); 1905 if (sc->ti_hwrev == TI_HWREV_TIGON_II) { 1906 TI_SETBIT(sc, TI_PCI_STATE, TI_PCISTATE_USE_MEM_RD_MULT); 1907 } 1908 1909 /* Clear the read/write max DMA parameters. */ 1910 TI_CLRBIT(sc, TI_PCI_STATE, (TI_PCISTATE_WRITE_MAXDMA| 1911 TI_PCISTATE_READ_MAXDMA)); 1912 1913 /* Get cache line size. */ 1914 cacheline = CSR_READ_4(sc, TI_PCI_BIST) & 0xFF; 1915 1916 /* 1917 * If the system has set enabled the PCI memory write 1918 * and invalidate command in the command register, set 1919 * the write max parameter accordingly. This is necessary 1920 * to use MWI with the Tigon 2. 1921 */ 1922 if (CSR_READ_4(sc, TI_PCI_CMDSTAT) & PCIM_CMD_MWIEN) { 1923 switch (cacheline) { 1924 case 1: 1925 case 4: 1926 case 8: 1927 case 16: 1928 case 32: 1929 case 64: 1930 break; 1931 default: 1932 /* Disable PCI memory write and invalidate. */ 1933 if (bootverbose) 1934 device_printf(sc->ti_dev, "cache line size %d" 1935 " not supported; disabling PCI MWI\n", 1936 cacheline); 1937 CSR_WRITE_4(sc, TI_PCI_CMDSTAT, CSR_READ_4(sc, 1938 TI_PCI_CMDSTAT) & ~PCIM_CMD_MWIEN); 1939 break; 1940 } 1941 } 1942 1943 TI_SETBIT(sc, TI_PCI_STATE, pci_writemax); 1944 1945 /* This sets the min dma param all the way up (0xff). */ 1946 TI_SETBIT(sc, TI_PCI_STATE, TI_PCISTATE_MINDMA); 1947 1948 if (sc->ti_hdrsplit) 1949 hdrsplit = TI_OPMODE_JUMBO_HDRSPLIT; 1950 else 1951 hdrsplit = 0; 1952 1953 /* Configure DMA variables. */ 1954#if BYTE_ORDER == BIG_ENDIAN 1955 CSR_WRITE_4(sc, TI_GCR_OPMODE, TI_OPMODE_BYTESWAP_BD | 1956 TI_OPMODE_BYTESWAP_DATA | TI_OPMODE_WORDSWAP_BD | 1957 TI_OPMODE_WARN_ENB | TI_OPMODE_FATAL_ENB | 1958 TI_OPMODE_DONT_FRAG_JUMBO | hdrsplit); 1959#else /* BYTE_ORDER */ 1960 CSR_WRITE_4(sc, TI_GCR_OPMODE, TI_OPMODE_BYTESWAP_DATA| 1961 TI_OPMODE_WORDSWAP_BD|TI_OPMODE_DONT_FRAG_JUMBO| 1962 TI_OPMODE_WARN_ENB|TI_OPMODE_FATAL_ENB | hdrsplit); 1963#endif /* BYTE_ORDER */ 1964 1965 /* 1966 * Only allow 1 DMA channel to be active at a time. 1967 * I don't think this is a good idea, but without it 1968 * the firmware racks up lots of nicDmaReadRingFull 1969 * errors. This is not compatible with hardware checksums. 1970 */ 1971 if (sc->ti_ifp->if_hwassist == 0) 1972 TI_SETBIT(sc, TI_GCR_OPMODE, TI_OPMODE_1_DMA_ACTIVE); 1973 1974 /* Recommended settings from Tigon manual. */ 1975 CSR_WRITE_4(sc, TI_GCR_DMA_WRITECFG, TI_DMA_STATE_THRESH_8W); 1976 CSR_WRITE_4(sc, TI_GCR_DMA_READCFG, TI_DMA_STATE_THRESH_8W); 1977 1978 if (ti_64bitslot_war(sc)) { 1979 device_printf(sc->ti_dev, "bios thinks we're in a 64 bit slot, " 1980 "but we aren't"); 1981 return (EINVAL); 1982 } 1983 1984 return (0); 1985} 1986 1987/* 1988 * Initialize the general information block and firmware, and 1989 * start the CPU(s) running. 1990 */ 1991static int 1992ti_gibinit(struct ti_softc *sc) 1993{ 1994 struct ifnet *ifp; 1995 struct ti_rcb *rcb; 1996 uint32_t rdphys; 1997 int i; 1998 1999 TI_LOCK_ASSERT(sc); 2000 2001 ifp = sc->ti_ifp; 2002 rdphys = sc->ti_rdata_phys; 2003 2004 /* Disable interrupts for now. */ 2005 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 1); 2006 2007 /* 2008 * Tell the chip where to find the general information block. 2009 * While this struct could go into >4GB memory, we allocate it in a 2010 * single slab with the other descriptors, and those don't seem to 2011 * support being located in a 64-bit region. 2012 */ 2013 CSR_WRITE_4(sc, TI_GCR_GENINFO_HI, 0); 2014 CSR_WRITE_4(sc, TI_GCR_GENINFO_LO, rdphys + TI_RD_OFF(ti_info)); 2015 2016 /* Load the firmware into SRAM. */ 2017 ti_loadfw(sc); 2018 2019 /* Set up the contents of the general info and ring control blocks. */ 2020 2021 /* Set up the event ring and producer pointer. */ 2022 rcb = &sc->ti_rdata->ti_info.ti_ev_rcb; 2023 2024 TI_HOSTADDR(rcb->ti_hostaddr) = rdphys + TI_RD_OFF(ti_event_ring); 2025 rcb->ti_flags = 0; 2026 TI_HOSTADDR(sc->ti_rdata->ti_info.ti_ev_prodidx_ptr) = 2027 rdphys + TI_RD_OFF(ti_ev_prodidx_r); 2028 sc->ti_ev_prodidx.ti_idx = 0; 2029 CSR_WRITE_4(sc, TI_GCR_EVENTCONS_IDX, 0); 2030 sc->ti_ev_saved_considx = 0; 2031 2032 /* Set up the command ring and producer mailbox. */ 2033 rcb = &sc->ti_rdata->ti_info.ti_cmd_rcb; 2034 2035 TI_HOSTADDR(rcb->ti_hostaddr) = TI_GCR_NIC_ADDR(TI_GCR_CMDRING); 2036 rcb->ti_flags = 0; 2037 rcb->ti_max_len = 0; 2038 for (i = 0; i < TI_CMD_RING_CNT; i++) { 2039 CSR_WRITE_4(sc, TI_GCR_CMDRING + (i * 4), 0); 2040 } 2041 CSR_WRITE_4(sc, TI_GCR_CMDCONS_IDX, 0); 2042 CSR_WRITE_4(sc, TI_MB_CMDPROD_IDX, 0); 2043 sc->ti_cmd_saved_prodidx = 0; 2044 2045 /* 2046 * Assign the address of the stats refresh buffer. 2047 * We re-use the current stats buffer for this to 2048 * conserve memory. 2049 */ 2050 TI_HOSTADDR(sc->ti_rdata->ti_info.ti_refresh_stats_ptr) = 2051 rdphys + TI_RD_OFF(ti_info.ti_stats); 2052 2053 /* Set up the standard receive ring. */ 2054 rcb = &sc->ti_rdata->ti_info.ti_std_rx_rcb; 2055 TI_HOSTADDR(rcb->ti_hostaddr) = rdphys + TI_RD_OFF(ti_rx_std_ring); 2056 rcb->ti_max_len = TI_FRAMELEN; 2057 rcb->ti_flags = 0; 2058 if (sc->ti_ifp->if_hwassist) 2059 rcb->ti_flags |= TI_RCB_FLAG_TCP_UDP_CKSUM | 2060 TI_RCB_FLAG_IP_CKSUM | TI_RCB_FLAG_NO_PHDR_CKSUM; 2061 rcb->ti_flags |= TI_RCB_FLAG_VLAN_ASSIST; 2062 2063 /* Set up the jumbo receive ring. */ 2064 rcb = &sc->ti_rdata->ti_info.ti_jumbo_rx_rcb; 2065 TI_HOSTADDR(rcb->ti_hostaddr) = rdphys + TI_RD_OFF(ti_rx_jumbo_ring); 2066 2067#ifdef TI_PRIVATE_JUMBOS 2068 rcb->ti_max_len = TI_JUMBO_FRAMELEN; 2069 rcb->ti_flags = 0; 2070#else 2071 rcb->ti_max_len = PAGE_SIZE; 2072 rcb->ti_flags = TI_RCB_FLAG_USE_EXT_RX_BD; 2073#endif 2074 if (sc->ti_ifp->if_hwassist) 2075 rcb->ti_flags |= TI_RCB_FLAG_TCP_UDP_CKSUM | 2076 TI_RCB_FLAG_IP_CKSUM | TI_RCB_FLAG_NO_PHDR_CKSUM; 2077 rcb->ti_flags |= TI_RCB_FLAG_VLAN_ASSIST; 2078 2079 /* 2080 * Set up the mini ring. Only activated on the 2081 * Tigon 2 but the slot in the config block is 2082 * still there on the Tigon 1. 2083 */ 2084 rcb = &sc->ti_rdata->ti_info.ti_mini_rx_rcb; 2085 TI_HOSTADDR(rcb->ti_hostaddr) = rdphys + TI_RD_OFF(ti_rx_mini_ring); 2086 rcb->ti_max_len = MHLEN - ETHER_ALIGN; 2087 if (sc->ti_hwrev == TI_HWREV_TIGON) 2088 rcb->ti_flags = TI_RCB_FLAG_RING_DISABLED; 2089 else 2090 rcb->ti_flags = 0; 2091 if (sc->ti_ifp->if_hwassist) 2092 rcb->ti_flags |= TI_RCB_FLAG_TCP_UDP_CKSUM | 2093 TI_RCB_FLAG_IP_CKSUM | TI_RCB_FLAG_NO_PHDR_CKSUM; 2094 rcb->ti_flags |= TI_RCB_FLAG_VLAN_ASSIST; 2095 2096 /* 2097 * Set up the receive return ring. 2098 */ 2099 rcb = &sc->ti_rdata->ti_info.ti_return_rcb; 2100 TI_HOSTADDR(rcb->ti_hostaddr) = rdphys + TI_RD_OFF(ti_rx_return_ring); 2101 rcb->ti_flags = 0; 2102 rcb->ti_max_len = TI_RETURN_RING_CNT; 2103 TI_HOSTADDR(sc->ti_rdata->ti_info.ti_return_prodidx_ptr) = 2104 rdphys + TI_RD_OFF(ti_return_prodidx_r); 2105 2106 /* 2107 * Set up the tx ring. Note: for the Tigon 2, we have the option 2108 * of putting the transmit ring in the host's address space and 2109 * letting the chip DMA it instead of leaving the ring in the NIC's 2110 * memory and accessing it through the shared memory region. We 2111 * do this for the Tigon 2, but it doesn't work on the Tigon 1, 2112 * so we have to revert to the shared memory scheme if we detect 2113 * a Tigon 1 chip. 2114 */ 2115 CSR_WRITE_4(sc, TI_WINBASE, TI_TX_RING_BASE); 2116 bzero((char *)sc->ti_rdata->ti_tx_ring, 2117 TI_TX_RING_CNT * sizeof(struct ti_tx_desc)); 2118 rcb = &sc->ti_rdata->ti_info.ti_tx_rcb; 2119 if (sc->ti_hwrev == TI_HWREV_TIGON) 2120 rcb->ti_flags = 0; 2121 else 2122 rcb->ti_flags = TI_RCB_FLAG_HOST_RING; 2123 rcb->ti_flags |= TI_RCB_FLAG_VLAN_ASSIST; 2124 if (sc->ti_ifp->if_hwassist) 2125 rcb->ti_flags |= TI_RCB_FLAG_TCP_UDP_CKSUM | 2126 TI_RCB_FLAG_IP_CKSUM | TI_RCB_FLAG_NO_PHDR_CKSUM; 2127 rcb->ti_max_len = TI_TX_RING_CNT; 2128 if (sc->ti_hwrev == TI_HWREV_TIGON) 2129 TI_HOSTADDR(rcb->ti_hostaddr) = TI_TX_RING_BASE; 2130 else 2131 TI_HOSTADDR(rcb->ti_hostaddr) = rdphys + TI_RD_OFF(ti_tx_ring); 2132 TI_HOSTADDR(sc->ti_rdata->ti_info.ti_tx_considx_ptr) = 2133 rdphys + TI_RD_OFF(ti_tx_considx_r); 2134 2135 bus_dmamap_sync(sc->ti_rdata_dmat, sc->ti_rdata_dmamap, 2136 BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); 2137 2138 /* Set up tuneables */ 2139#if 0 2140 if (ifp->if_mtu > (ETHERMTU + ETHER_HDR_LEN + ETHER_CRC_LEN)) 2141 CSR_WRITE_4(sc, TI_GCR_RX_COAL_TICKS, 2142 (sc->ti_rx_coal_ticks / 10)); 2143 else 2144#endif 2145 CSR_WRITE_4(sc, TI_GCR_RX_COAL_TICKS, sc->ti_rx_coal_ticks); 2146 CSR_WRITE_4(sc, TI_GCR_TX_COAL_TICKS, sc->ti_tx_coal_ticks); 2147 CSR_WRITE_4(sc, TI_GCR_STAT_TICKS, sc->ti_stat_ticks); 2148 CSR_WRITE_4(sc, TI_GCR_RX_MAX_COAL_BD, sc->ti_rx_max_coal_bds); 2149 CSR_WRITE_4(sc, TI_GCR_TX_MAX_COAL_BD, sc->ti_tx_max_coal_bds); 2150 CSR_WRITE_4(sc, TI_GCR_TX_BUFFER_RATIO, sc->ti_tx_buf_ratio); 2151 2152 /* Turn interrupts on. */ 2153 CSR_WRITE_4(sc, TI_GCR_MASK_INTRS, 0); 2154 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 0); 2155 2156 /* Start CPU. */ 2157 TI_CLRBIT(sc, TI_CPU_STATE, (TI_CPUSTATE_HALT|TI_CPUSTATE_STEP)); 2158 2159 return (0); 2160} 2161 2162static void 2163ti_rdata_cb(void *arg, bus_dma_segment_t *segs, int nseg, int error) 2164{ 2165 struct ti_softc *sc; 2166 2167 sc = arg; 2168 if (error || nseg != 1) 2169 return; 2170 2171 /* 2172 * All of the Tigon data structures need to live at <4GB. This 2173 * cast is fine since busdma was told about this constraint. 2174 */ 2175 sc->ti_rdata_phys = segs[0].ds_addr; 2176 return; 2177} 2178 2179/* 2180 * Probe for a Tigon chip. Check the PCI vendor and device IDs 2181 * against our list and return its name if we find a match. 2182 */ 2183static int 2184ti_probe(device_t dev) 2185{ 2186 const struct ti_type *t; 2187 2188 t = ti_devs; 2189 2190 while (t->ti_name != NULL) { 2191 if ((pci_get_vendor(dev) == t->ti_vid) && 2192 (pci_get_device(dev) == t->ti_did)) { 2193 device_set_desc(dev, t->ti_name); 2194 return (BUS_PROBE_DEFAULT); 2195 } 2196 t++; 2197 } 2198 2199 return (ENXIO); 2200} 2201 2202static int 2203ti_attach(device_t dev) 2204{ 2205 struct ifnet *ifp; 2206 struct ti_softc *sc; 2207 int error = 0, rid; 2208 u_char eaddr[6]; 2209 2210 sc = device_get_softc(dev); 2211 sc->ti_unit = device_get_unit(dev); 2212 sc->ti_dev = dev; 2213 2214 mtx_init(&sc->ti_mtx, device_get_nameunit(dev), MTX_NETWORK_LOCK, 2215 MTX_DEF); 2216 callout_init_mtx(&sc->ti_watchdog, &sc->ti_mtx, 0); 2217 ifmedia_init(&sc->ifmedia, IFM_IMASK, ti_ifmedia_upd, ti_ifmedia_sts); 2218 ifp = sc->ti_ifp = if_alloc(IFT_ETHER); 2219 if (ifp == NULL) { 2220 device_printf(dev, "can not if_alloc()\n"); 2221 error = ENOSPC; 2222 goto fail; 2223 } 2224 sc->ti_ifp->if_capabilities = IFCAP_HWCSUM | 2225 IFCAP_VLAN_HWTAGGING | IFCAP_VLAN_MTU; 2226 sc->ti_ifp->if_capenable = sc->ti_ifp->if_capabilities; 2227 2228 /* 2229 * Map control/status registers. 2230 */ 2231 pci_enable_busmaster(dev); 2232 2233 rid = TI_PCI_LOMEM; 2234 sc->ti_res = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &rid, 2235 RF_ACTIVE); 2236 2237 if (sc->ti_res == NULL) { 2238 device_printf(dev, "couldn't map memory\n"); 2239 error = ENXIO; 2240 goto fail; 2241 } 2242 2243 sc->ti_btag = rman_get_bustag(sc->ti_res); 2244 sc->ti_bhandle = rman_get_bushandle(sc->ti_res); 2245 2246 /* Allocate interrupt */ 2247 rid = 0; 2248 2249 sc->ti_irq = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid, 2250 RF_SHAREABLE | RF_ACTIVE); 2251 2252 if (sc->ti_irq == NULL) { 2253 device_printf(dev, "couldn't map interrupt\n"); 2254 error = ENXIO; 2255 goto fail; 2256 } 2257 2258 if (ti_chipinit(sc)) { 2259 device_printf(dev, "chip initialization failed\n"); 2260 error = ENXIO; 2261 goto fail; 2262 } 2263 2264 /* Zero out the NIC's on-board SRAM. */ 2265 ti_mem_zero(sc, 0x2000, 0x100000 - 0x2000); 2266 2267 /* Init again -- zeroing memory may have clobbered some registers. */ 2268 if (ti_chipinit(sc)) { 2269 device_printf(dev, "chip initialization failed\n"); 2270 error = ENXIO; 2271 goto fail; 2272 } 2273 2274 /* 2275 * Get station address from the EEPROM. Note: the manual states 2276 * that the MAC address is at offset 0x8c, however the data is 2277 * stored as two longwords (since that's how it's loaded into 2278 * the NIC). This means the MAC address is actually preceded 2279 * by two zero bytes. We need to skip over those. 2280 */ 2281 if (ti_read_eeprom(sc, eaddr, 2282 TI_EE_MAC_OFFSET + 2, ETHER_ADDR_LEN)) { 2283 device_printf(dev, "failed to read station address\n"); 2284 error = ENXIO; 2285 goto fail; 2286 } 2287 2288 /* Allocate the general information block and ring buffers. */ 2289 if (bus_dma_tag_create(bus_get_dma_tag(dev), /* parent */ 2290 1, 0, /* algnmnt, boundary */ 2291 BUS_SPACE_MAXADDR, /* lowaddr */ 2292 BUS_SPACE_MAXADDR, /* highaddr */ 2293 NULL, NULL, /* filter, filterarg */ 2294 BUS_SPACE_MAXSIZE_32BIT,/* maxsize */ 2295 0, /* nsegments */ 2296 BUS_SPACE_MAXSIZE_32BIT,/* maxsegsize */ 2297 0, /* flags */ 2298 NULL, NULL, /* lockfunc, lockarg */ 2299 &sc->ti_parent_dmat) != 0) { 2300 device_printf(dev, "Failed to allocate parent dmat\n"); 2301 error = ENOMEM; 2302 goto fail; 2303 } 2304 2305 if (bus_dma_tag_create(sc->ti_parent_dmat, /* parent */ 2306 PAGE_SIZE, 0, /* algnmnt, boundary */ 2307 BUS_SPACE_MAXADDR_32BIT,/* lowaddr */ 2308 BUS_SPACE_MAXADDR, /* highaddr */ 2309 NULL, NULL, /* filter, filterarg */ 2310 sizeof(struct ti_ring_data), /* maxsize */ 2311 1, /* nsegments */ 2312 sizeof(struct ti_ring_data), /* maxsegsize */ 2313 0, /* flags */ 2314 NULL, NULL, /* lockfunc, lockarg */ 2315 &sc->ti_rdata_dmat) != 0) { 2316 device_printf(dev, "Failed to allocate rdata dmat\n"); 2317 error = ENOMEM; 2318 goto fail; 2319 } 2320 2321 if (bus_dmamem_alloc(sc->ti_rdata_dmat, (void**)&sc->ti_rdata, 2322 BUS_DMA_NOWAIT | BUS_DMA_COHERENT, 2323 &sc->ti_rdata_dmamap) != 0) { 2324 device_printf(dev, "Failed to allocate rdata memory\n"); 2325 error = ENOMEM; 2326 goto fail; 2327 } 2328 2329 if (bus_dmamap_load(sc->ti_rdata_dmat, sc->ti_rdata_dmamap, 2330 sc->ti_rdata, sizeof(struct ti_ring_data), 2331 ti_rdata_cb, sc, BUS_DMA_NOWAIT) != 0) { 2332 device_printf(dev, "Failed to load rdata segments\n"); 2333 error = ENOMEM; 2334 goto fail; 2335 } 2336 2337 bzero(sc->ti_rdata, sizeof(struct ti_ring_data)); 2338 2339 /* Try to allocate memory for jumbo buffers. */ 2340 if (ti_alloc_jumbo_mem(sc)) { 2341 device_printf(dev, "jumbo buffer allocation failed\n"); 2342 error = ENXIO; 2343 goto fail; 2344 } 2345 2346 if (bus_dma_tag_create(sc->ti_parent_dmat, /* parent */ 2347 1, 0, /* algnmnt, boundary */ 2348 BUS_SPACE_MAXADDR, /* lowaddr */ 2349 BUS_SPACE_MAXADDR, /* highaddr */ 2350 NULL, NULL, /* filter, filterarg */ 2351 MCLBYTES * TI_MAXTXSEGS,/* maxsize */ 2352 TI_MAXTXSEGS, /* nsegments */ 2353 MCLBYTES, /* maxsegsize */ 2354 0, /* flags */ 2355 NULL, NULL, /* lockfunc, lockarg */ 2356 &sc->ti_mbuftx_dmat) != 0) { 2357 device_printf(dev, "Failed to allocate rdata dmat\n"); 2358 error = ENOMEM; 2359 goto fail; 2360 } 2361 2362 if (bus_dma_tag_create(sc->ti_parent_dmat, /* parent */ 2363 1, 0, /* algnmnt, boundary */ 2364 BUS_SPACE_MAXADDR, /* lowaddr */ 2365 BUS_SPACE_MAXADDR, /* highaddr */ 2366 NULL, NULL, /* filter, filterarg */ 2367 MCLBYTES, /* maxsize */ 2368 1, /* nsegments */ 2369 MCLBYTES, /* maxsegsize */ 2370 0, /* flags */ 2371 NULL, NULL, /* lockfunc, lockarg */ 2372 &sc->ti_mbufrx_dmat) != 0) { 2373 device_printf(dev, "Failed to allocate rdata dmat\n"); 2374 error = ENOMEM; 2375 goto fail; 2376 } 2377 2378 if (ti_alloc_dmamaps(sc)) { 2379 device_printf(dev, "dma map creation failed\n"); 2380 error = ENXIO; 2381 goto fail; 2382 } 2383 2384 /* 2385 * We really need a better way to tell a 1000baseTX card 2386 * from a 1000baseSX one, since in theory there could be 2387 * OEMed 1000baseTX cards from lame vendors who aren't 2388 * clever enough to change the PCI ID. For the moment 2389 * though, the AceNIC is the only copper card available. 2390 */ 2391 if (pci_get_vendor(dev) == ALT_VENDORID && 2392 pci_get_device(dev) == ALT_DEVICEID_ACENIC_COPPER) 2393 sc->ti_copper = 1; 2394 /* Ok, it's not the only copper card available. */ 2395 if (pci_get_vendor(dev) == NG_VENDORID && 2396 pci_get_device(dev) == NG_DEVICEID_GA620T) 2397 sc->ti_copper = 1; 2398 2399 /* Set default tuneable values. */ 2400 sc->ti_stat_ticks = 2 * TI_TICKS_PER_SEC; 2401#if 0 2402 sc->ti_rx_coal_ticks = TI_TICKS_PER_SEC / 5000; 2403#endif 2404 sc->ti_rx_coal_ticks = 170; 2405 sc->ti_tx_coal_ticks = TI_TICKS_PER_SEC / 500; 2406 sc->ti_rx_max_coal_bds = 64; 2407#if 0 2408 sc->ti_tx_max_coal_bds = 128; 2409#endif 2410 sc->ti_tx_max_coal_bds = 32; 2411 sc->ti_tx_buf_ratio = 21; 2412 2413 /* Set up ifnet structure */ 2414 ifp->if_softc = sc; 2415 if_initname(ifp, device_get_name(dev), device_get_unit(dev)); 2416 ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; 2417 ifp->if_ioctl = ti_ioctl; 2418 ifp->if_start = ti_start; 2419 ifp->if_init = ti_init; 2420 ifp->if_baudrate = 1000000000; 2421 ifp->if_snd.ifq_maxlen = TI_TX_RING_CNT - 1; 2422 2423 /* Set up ifmedia support. */ 2424 if (sc->ti_copper) { 2425 /* 2426 * Copper cards allow manual 10/100 mode selection, 2427 * but not manual 1000baseTX mode selection. Why? 2428 * Becuase currently there's no way to specify the 2429 * master/slave setting through the firmware interface, 2430 * so Alteon decided to just bag it and handle it 2431 * via autonegotiation. 2432 */ 2433 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T, 0, NULL); 2434 ifmedia_add(&sc->ifmedia, 2435 IFM_ETHER|IFM_10_T|IFM_FDX, 0, NULL); 2436 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_100_TX, 0, NULL); 2437 ifmedia_add(&sc->ifmedia, 2438 IFM_ETHER|IFM_100_TX|IFM_FDX, 0, NULL); 2439 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_1000_T, 0, NULL); 2440 ifmedia_add(&sc->ifmedia, 2441 IFM_ETHER|IFM_1000_T|IFM_FDX, 0, NULL); 2442 } else { 2443 /* Fiber cards don't support 10/100 modes. */ 2444 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_1000_SX, 0, NULL); 2445 ifmedia_add(&sc->ifmedia, 2446 IFM_ETHER|IFM_1000_SX|IFM_FDX, 0, NULL); 2447 } 2448 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_AUTO, 0, NULL); 2449 ifmedia_set(&sc->ifmedia, IFM_ETHER|IFM_AUTO); 2450 2451 /* 2452 * We're assuming here that card initialization is a sequential 2453 * thing. If it isn't, multiple cards probing at the same time 2454 * could stomp on the list of softcs here. 2455 */ 2456 2457 /* Register the device */ 2458 sc->dev = make_dev(&ti_cdevsw, sc->ti_unit, UID_ROOT, GID_OPERATOR, 2459 0600, "ti%d", sc->ti_unit); 2460 sc->dev->si_drv1 = sc; 2461 2462 /* 2463 * Call MI attach routine. 2464 */ 2465 ether_ifattach(ifp, eaddr); 2466 2467 /* Hook interrupt last to avoid having to lock softc */ 2468 error = bus_setup_intr(dev, sc->ti_irq, INTR_TYPE_NET|INTR_MPSAFE, 2469 NULL, ti_intr, sc, &sc->ti_intrhand); 2470 2471 if (error) { 2472 device_printf(dev, "couldn't set up irq\n"); 2473 goto fail; 2474 } 2475 2476fail: 2477 if (error) 2478 ti_detach(dev); 2479 2480 return (error); 2481} 2482 2483/* 2484 * Shutdown hardware and free up resources. This can be called any 2485 * time after the mutex has been initialized. It is called in both 2486 * the error case in attach and the normal detach case so it needs 2487 * to be careful about only freeing resources that have actually been 2488 * allocated. 2489 */ 2490static int 2491ti_detach(device_t dev) 2492{ 2493 struct ti_softc *sc; 2494 struct ifnet *ifp; 2495 2496 sc = device_get_softc(dev); 2497 if (sc->dev) 2498 destroy_dev(sc->dev); 2499 KASSERT(mtx_initialized(&sc->ti_mtx), ("ti mutex not initialized")); 2500 ifp = sc->ti_ifp; 2501 if (device_is_attached(dev)) { 2502 ether_ifdetach(ifp); 2503 TI_LOCK(sc); 2504 ti_stop(sc); 2505 TI_UNLOCK(sc); 2506 } 2507 2508 /* These should only be active if attach succeeded */ 2509 callout_drain(&sc->ti_watchdog); 2510 bus_generic_detach(dev); 2511 ti_free_dmamaps(sc); 2512 ifmedia_removeall(&sc->ifmedia); 2513 2514#ifdef TI_PRIVATE_JUMBOS 2515 if (sc->ti_cdata.ti_jumbo_buf) 2516 bus_dmamem_free(sc->ti_jumbo_dmat, sc->ti_cdata.ti_jumbo_buf, 2517 sc->ti_jumbo_dmamap); 2518#endif 2519 if (sc->ti_jumbo_dmat) 2520 bus_dma_tag_destroy(sc->ti_jumbo_dmat); 2521 if (sc->ti_mbuftx_dmat) 2522 bus_dma_tag_destroy(sc->ti_mbuftx_dmat); 2523 if (sc->ti_mbufrx_dmat) 2524 bus_dma_tag_destroy(sc->ti_mbufrx_dmat); 2525 if (sc->ti_rdata && sc->ti_rdata_dmamap) 2526 bus_dmamap_unload(sc->ti_rdata_dmat, sc->ti_rdata_dmamap); 2527 if (sc->ti_rdata) 2528 bus_dmamem_free(sc->ti_rdata_dmat, sc->ti_rdata, 2529 sc->ti_rdata_dmamap); 2530 if (sc->ti_rdata_dmat) 2531 bus_dma_tag_destroy(sc->ti_rdata_dmat); 2532 if (sc->ti_parent_dmat) 2533 bus_dma_tag_destroy(sc->ti_parent_dmat); 2534 if (sc->ti_intrhand) 2535 bus_teardown_intr(dev, sc->ti_irq, sc->ti_intrhand); 2536 if (sc->ti_irq) 2537 bus_release_resource(dev, SYS_RES_IRQ, 0, sc->ti_irq); 2538 if (sc->ti_res) { 2539 bus_release_resource(dev, SYS_RES_MEMORY, TI_PCI_LOMEM, 2540 sc->ti_res); 2541 } 2542 if (ifp) 2543 if_free(ifp); 2544 2545 mtx_destroy(&sc->ti_mtx); 2546 2547 return (0); 2548} 2549 2550#ifdef TI_JUMBO_HDRSPLIT 2551/* 2552 * If hdr_len is 0, that means that header splitting wasn't done on 2553 * this packet for some reason. The two most likely reasons are that 2554 * the protocol isn't a supported protocol for splitting, or this 2555 * packet had a fragment offset that wasn't 0. 2556 * 2557 * The header length, if it is non-zero, will always be the length of 2558 * the headers on the packet, but that length could be longer than the 2559 * first mbuf. So we take the minimum of the two as the actual 2560 * length. 2561 */ 2562static __inline void 2563ti_hdr_split(struct mbuf *top, int hdr_len, int pkt_len, int idx) 2564{ 2565 int i = 0; 2566 int lengths[4] = {0, 0, 0, 0}; 2567 struct mbuf *m, *mp; 2568 2569 if (hdr_len != 0) 2570 top->m_len = min(hdr_len, top->m_len); 2571 pkt_len -= top->m_len; 2572 lengths[i++] = top->m_len; 2573 2574 mp = top; 2575 for (m = top->m_next; m && pkt_len; m = m->m_next) { 2576 m->m_len = m->m_ext.ext_size = min(m->m_len, pkt_len); 2577 pkt_len -= m->m_len; 2578 lengths[i++] = m->m_len; 2579 mp = m; 2580 } 2581 2582#if 0 2583 if (hdr_len != 0) 2584 printf("got split packet: "); 2585 else 2586 printf("got non-split packet: "); 2587 2588 printf("%d,%d,%d,%d = %d\n", lengths[0], 2589 lengths[1], lengths[2], lengths[3], 2590 lengths[0] + lengths[1] + lengths[2] + 2591 lengths[3]); 2592#endif 2593 2594 if (pkt_len) 2595 panic("header splitting didn't"); 2596 2597 if (m) { 2598 m_freem(m); 2599 mp->m_next = NULL; 2600 2601 } 2602 if (mp->m_next != NULL) 2603 panic("ti_hdr_split: last mbuf in chain should be null"); 2604} 2605#endif /* TI_JUMBO_HDRSPLIT */ 2606 2607/* 2608 * Frame reception handling. This is called if there's a frame 2609 * on the receive return list. 2610 * 2611 * Note: we have to be able to handle three possibilities here: 2612 * 1) the frame is from the mini receive ring (can only happen) 2613 * on Tigon 2 boards) 2614 * 2) the frame is from the jumbo recieve ring 2615 * 3) the frame is from the standard receive ring 2616 */ 2617 2618static void 2619ti_rxeof(struct ti_softc *sc) 2620{ 2621 struct ifnet *ifp; 2622 bus_dmamap_t map; 2623 struct ti_cmd_desc cmd; 2624 2625 TI_LOCK_ASSERT(sc); 2626 2627 ifp = sc->ti_ifp; 2628 2629 while (sc->ti_rx_saved_considx != sc->ti_return_prodidx.ti_idx) { 2630 struct ti_rx_desc *cur_rx; 2631 struct mbuf *m = NULL; 2632 uint32_t rxidx; 2633 uint16_t vlan_tag = 0; 2634 int have_tag = 0; 2635 2636 cur_rx = 2637 &sc->ti_rdata->ti_rx_return_ring[sc->ti_rx_saved_considx]; 2638 rxidx = cur_rx->ti_idx; 2639 TI_INC(sc->ti_rx_saved_considx, TI_RETURN_RING_CNT); 2640 2641 if (cur_rx->ti_flags & TI_BDFLAG_VLAN_TAG) { 2642 have_tag = 1; 2643 vlan_tag = cur_rx->ti_vlan_tag & 0xfff; 2644 } 2645 2646 if (cur_rx->ti_flags & TI_BDFLAG_JUMBO_RING) { 2647 2648 TI_INC(sc->ti_jumbo, TI_JUMBO_RX_RING_CNT); 2649 m = sc->ti_cdata.ti_rx_jumbo_chain[rxidx]; 2650 sc->ti_cdata.ti_rx_jumbo_chain[rxidx] = NULL; 2651 map = sc->ti_cdata.ti_rx_jumbo_maps[rxidx]; 2652 bus_dmamap_sync(sc->ti_jumbo_dmat, map, 2653 BUS_DMASYNC_POSTREAD); 2654 bus_dmamap_unload(sc->ti_jumbo_dmat, map); 2655 if (cur_rx->ti_flags & TI_BDFLAG_ERROR) { 2656 ifp->if_ierrors++; 2657 ti_newbuf_jumbo(sc, sc->ti_jumbo, m); 2658 continue; 2659 } 2660 if (ti_newbuf_jumbo(sc, sc->ti_jumbo, NULL) == ENOBUFS) { 2661 ifp->if_ierrors++; 2662 ti_newbuf_jumbo(sc, sc->ti_jumbo, m); 2663 continue; 2664 } 2665#ifdef TI_PRIVATE_JUMBOS 2666 m->m_len = cur_rx->ti_len; 2667#else /* TI_PRIVATE_JUMBOS */ 2668#ifdef TI_JUMBO_HDRSPLIT 2669 if (sc->ti_hdrsplit) 2670 ti_hdr_split(m, TI_HOSTADDR(cur_rx->ti_addr), 2671 cur_rx->ti_len, rxidx); 2672 else 2673#endif /* TI_JUMBO_HDRSPLIT */ 2674 m_adj(m, cur_rx->ti_len - m->m_pkthdr.len); 2675#endif /* TI_PRIVATE_JUMBOS */ 2676 } else if (cur_rx->ti_flags & TI_BDFLAG_MINI_RING) { 2677 TI_INC(sc->ti_mini, TI_MINI_RX_RING_CNT); 2678 m = sc->ti_cdata.ti_rx_mini_chain[rxidx]; 2679 sc->ti_cdata.ti_rx_mini_chain[rxidx] = NULL; 2680 map = sc->ti_cdata.ti_rx_mini_maps[rxidx]; 2681 bus_dmamap_sync(sc->ti_mbufrx_dmat, map, 2682 BUS_DMASYNC_POSTREAD); 2683 bus_dmamap_unload(sc->ti_mbufrx_dmat, map); 2684 if (cur_rx->ti_flags & TI_BDFLAG_ERROR) { 2685 ifp->if_ierrors++; 2686 ti_newbuf_mini(sc, sc->ti_mini, m); 2687 continue; 2688 } 2689 if (ti_newbuf_mini(sc, sc->ti_mini, NULL) == ENOBUFS) { 2690 ifp->if_ierrors++; 2691 ti_newbuf_mini(sc, sc->ti_mini, m); 2692 continue; 2693 } 2694 m->m_len = cur_rx->ti_len; 2695 } else { 2696 TI_INC(sc->ti_std, TI_STD_RX_RING_CNT); 2697 m = sc->ti_cdata.ti_rx_std_chain[rxidx]; 2698 sc->ti_cdata.ti_rx_std_chain[rxidx] = NULL; 2699 map = sc->ti_cdata.ti_rx_std_maps[rxidx]; 2700 bus_dmamap_sync(sc->ti_mbufrx_dmat, map, 2701 BUS_DMASYNC_POSTREAD); 2702 bus_dmamap_unload(sc->ti_mbufrx_dmat, map); 2703 if (cur_rx->ti_flags & TI_BDFLAG_ERROR) { 2704 ifp->if_ierrors++; 2705 ti_newbuf_std(sc, sc->ti_std, m); 2706 continue; 2707 } 2708 if (ti_newbuf_std(sc, sc->ti_std, NULL) == ENOBUFS) { 2709 ifp->if_ierrors++; 2710 ti_newbuf_std(sc, sc->ti_std, m); 2711 continue; 2712 } 2713 m->m_len = cur_rx->ti_len; 2714 } 2715 2716 m->m_pkthdr.len = cur_rx->ti_len; 2717 ifp->if_ipackets++; 2718 m->m_pkthdr.rcvif = ifp; 2719 2720 if (ifp->if_hwassist) { 2721 m->m_pkthdr.csum_flags |= CSUM_IP_CHECKED | 2722 CSUM_DATA_VALID; 2723 if ((cur_rx->ti_ip_cksum ^ 0xffff) == 0) 2724 m->m_pkthdr.csum_flags |= CSUM_IP_VALID; 2725 m->m_pkthdr.csum_data = cur_rx->ti_tcp_udp_cksum; 2726 } 2727 2728 /* 2729 * If we received a packet with a vlan tag, 2730 * tag it before passing the packet upward. 2731 */ 2732 if (have_tag) { 2733 m->m_pkthdr.ether_vtag = vlan_tag; 2734 m->m_flags |= M_VLANTAG; 2735 } 2736 TI_UNLOCK(sc); 2737 (*ifp->if_input)(ifp, m); 2738 TI_LOCK(sc); 2739 } 2740 2741 /* Only necessary on the Tigon 1. */ 2742 if (sc->ti_hwrev == TI_HWREV_TIGON) 2743 CSR_WRITE_4(sc, TI_GCR_RXRETURNCONS_IDX, 2744 sc->ti_rx_saved_considx); 2745 2746 TI_UPDATE_STDPROD(sc, sc->ti_std); 2747 TI_UPDATE_MINIPROD(sc, sc->ti_mini); 2748 TI_UPDATE_JUMBOPROD(sc, sc->ti_jumbo); 2749} 2750 2751static void 2752ti_txeof(struct ti_softc *sc) 2753{ 2754 struct ti_txdesc *txd; 2755 struct ti_tx_desc txdesc; 2756 struct ti_tx_desc *cur_tx = NULL; 2757 struct ifnet *ifp; 2758 int idx; 2759 2760 ifp = sc->ti_ifp; 2761 2762 txd = STAILQ_FIRST(&sc->ti_cdata.ti_txbusyq); 2763 if (txd == NULL) 2764 return; 2765 /* 2766 * Go through our tx ring and free mbufs for those 2767 * frames that have been sent. 2768 */ 2769 for (idx = sc->ti_tx_saved_considx; idx != sc->ti_tx_considx.ti_idx; 2770 TI_INC(idx, TI_TX_RING_CNT)) { 2771 if (sc->ti_hwrev == TI_HWREV_TIGON) { 2772 ti_mem_read(sc, TI_TX_RING_BASE + idx * sizeof(txdesc), 2773 sizeof(txdesc), &txdesc); 2774 cur_tx = &txdesc; 2775 } else 2776 cur_tx = &sc->ti_rdata->ti_tx_ring[idx]; 2777 sc->ti_txcnt--; 2778 ifp->if_drv_flags &= ~IFF_DRV_OACTIVE; 2779 if ((cur_tx->ti_flags & TI_BDFLAG_END) == 0) 2780 continue; 2781 bus_dmamap_sync(sc->ti_mbuftx_dmat, txd->tx_dmamap, 2782 BUS_DMASYNC_POSTWRITE); 2783 bus_dmamap_unload(sc->ti_mbuftx_dmat, txd->tx_dmamap); 2784 2785 ifp->if_opackets++; 2786 m_freem(txd->tx_m); 2787 txd->tx_m = NULL; 2788 STAILQ_REMOVE_HEAD(&sc->ti_cdata.ti_txbusyq, tx_q); 2789 STAILQ_INSERT_TAIL(&sc->ti_cdata.ti_txfreeq, txd, tx_q); 2790 txd = STAILQ_FIRST(&sc->ti_cdata.ti_txbusyq); 2791 } 2792 sc->ti_tx_saved_considx = idx; 2793 2794 sc->ti_timer = sc->ti_txcnt > 0 ? 5 : 0; 2795} 2796 2797static void 2798ti_intr(void *xsc) 2799{ 2800 struct ti_softc *sc; 2801 struct ifnet *ifp; 2802 2803 sc = xsc; 2804 TI_LOCK(sc); 2805 ifp = sc->ti_ifp; 2806 2807/*#ifdef notdef*/ 2808 /* Avoid this for now -- checking this register is expensive. */ 2809 /* Make sure this is really our interrupt. */ 2810 if (!(CSR_READ_4(sc, TI_MISC_HOST_CTL) & TI_MHC_INTSTATE)) { 2811 TI_UNLOCK(sc); 2812 return; 2813 } 2814/*#endif*/ 2815 2816 /* Ack interrupt and stop others from occuring. */ 2817 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 1); 2818 2819 if (ifp->if_drv_flags & IFF_DRV_RUNNING) { 2820 /* Check RX return ring producer/consumer */ 2821 ti_rxeof(sc); 2822 2823 /* Check TX ring producer/consumer */ 2824 ti_txeof(sc); 2825 } 2826 2827 ti_handle_events(sc); 2828 2829 /* Re-enable interrupts. */ 2830 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 0); 2831 2832 if (ifp->if_drv_flags & IFF_DRV_RUNNING && 2833 ifp->if_snd.ifq_head != NULL) 2834 ti_start_locked(ifp); 2835 2836 TI_UNLOCK(sc); 2837} 2838 2839static void 2840ti_stats_update(struct ti_softc *sc) 2841{ 2842 struct ifnet *ifp; 2843 2844 ifp = sc->ti_ifp; 2845 2846 bus_dmamap_sync(sc->ti_rdata_dmat, sc->ti_rdata_dmamap, 2847 BUS_DMASYNC_POSTREAD); 2848 2849 ifp->if_collisions += 2850 (sc->ti_rdata->ti_info.ti_stats.dot3StatsSingleCollisionFrames + 2851 sc->ti_rdata->ti_info.ti_stats.dot3StatsMultipleCollisionFrames + 2852 sc->ti_rdata->ti_info.ti_stats.dot3StatsExcessiveCollisions + 2853 sc->ti_rdata->ti_info.ti_stats.dot3StatsLateCollisions) - 2854 ifp->if_collisions; 2855 2856 bus_dmamap_sync(sc->ti_rdata_dmat, sc->ti_rdata_dmamap, 2857 BUS_DMASYNC_PREREAD); 2858} 2859 2860/* 2861 * Encapsulate an mbuf chain in the tx ring by coupling the mbuf data 2862 * pointers to descriptors. 2863 */ 2864static int 2865ti_encap(struct ti_softc *sc, struct mbuf **m_head) 2866{ 2867 struct ti_txdesc *txd; 2868 struct ti_tx_desc *f; 2869 struct ti_tx_desc txdesc; 2870 struct mbuf *m; 2871 bus_dma_segment_t txsegs[TI_MAXTXSEGS]; 2872 uint16_t csum_flags; 2873 int error, frag, i, nseg; 2874 2875 if ((txd = STAILQ_FIRST(&sc->ti_cdata.ti_txfreeq)) == NULL) 2876 return (ENOBUFS); 2877 2878 error = bus_dmamap_load_mbuf_sg(sc->ti_mbuftx_dmat, txd->tx_dmamap, 2879 *m_head, txsegs, &nseg, 0); 2880 if (error == EFBIG) { 2881 m = m_defrag(*m_head, M_DONTWAIT); 2882 if (m == NULL) { 2883 m_freem(*m_head); 2884 *m_head = NULL; 2885 return (ENOMEM); 2886 } 2887 *m_head = m; 2888 error = bus_dmamap_load_mbuf_sg(sc->ti_mbuftx_dmat, 2889 txd->tx_dmamap, *m_head, txsegs, &nseg, 0); 2890 if (error) { 2891 m_freem(*m_head); 2892 *m_head = NULL; 2893 return (error); 2894 } 2895 } else if (error != 0) 2896 return (error); 2897 if (nseg == 0) { 2898 m_freem(*m_head); 2899 *m_head = NULL; 2900 return (EIO); 2901 } 2902 2903 if (sc->ti_txcnt + nseg >= TI_TX_RING_CNT) { 2904 bus_dmamap_unload(sc->ti_mbuftx_dmat, txd->tx_dmamap); 2905 return (ENOBUFS); 2906 } 2907 2908 m = *m_head; 2909 csum_flags = 0; 2910 if (m->m_pkthdr.csum_flags) { 2911 if (m->m_pkthdr.csum_flags & CSUM_IP) 2912 csum_flags |= TI_BDFLAG_IP_CKSUM; 2913 if (m->m_pkthdr.csum_flags & (CSUM_TCP | CSUM_UDP)) 2914 csum_flags |= TI_BDFLAG_TCP_UDP_CKSUM; 2915 if (m->m_flags & M_LASTFRAG) 2916 csum_flags |= TI_BDFLAG_IP_FRAG_END; 2917 else if (m->m_flags & M_FRAG) 2918 csum_flags |= TI_BDFLAG_IP_FRAG; 2919 } 2920 2921 bus_dmamap_sync(sc->ti_mbuftx_dmat, txd->tx_dmamap, 2922 BUS_DMASYNC_PREWRITE); 2923 bus_dmamap_sync(sc->ti_rdata_dmat, sc->ti_rdata_dmamap, 2924 BUS_DMASYNC_PREWRITE); 2925 2926 frag = sc->ti_tx_saved_prodidx; 2927 for (i = 0; i < nseg; i++) { 2928 if (sc->ti_hwrev == TI_HWREV_TIGON) { 2929 bzero(&txdesc, sizeof(txdesc)); 2930 f = &txdesc; 2931 } else 2932 f = &sc->ti_rdata->ti_tx_ring[frag]; 2933 ti_hostaddr64(&f->ti_addr, txsegs[i].ds_addr); 2934 f->ti_len = txsegs[i].ds_len; 2935 f->ti_flags = csum_flags; 2936 if (m->m_flags & M_VLANTAG) { 2937 f->ti_flags |= TI_BDFLAG_VLAN_TAG; 2938 f->ti_vlan_tag = m->m_pkthdr.ether_vtag & 0xfff; 2939 } else { 2940 f->ti_vlan_tag = 0; 2941 } 2942 2943 if (sc->ti_hwrev == TI_HWREV_TIGON) 2944 ti_mem_write(sc, TI_TX_RING_BASE + frag * 2945 sizeof(txdesc), sizeof(txdesc), &txdesc); 2946 TI_INC(frag, TI_TX_RING_CNT); 2947 } 2948 2949 sc->ti_tx_saved_prodidx = frag; 2950 /* set TI_BDFLAG_END on the last descriptor */ 2951 frag = (frag + TI_TX_RING_CNT - 1) % TI_TX_RING_CNT; 2952 if (sc->ti_hwrev == TI_HWREV_TIGON) { 2953 txdesc.ti_flags |= TI_BDFLAG_END; 2954 ti_mem_write(sc, TI_TX_RING_BASE + frag * sizeof(txdesc), 2955 sizeof(txdesc), &txdesc); 2956 } else 2957 sc->ti_rdata->ti_tx_ring[frag].ti_flags |= TI_BDFLAG_END; 2958 2959 STAILQ_REMOVE_HEAD(&sc->ti_cdata.ti_txfreeq, tx_q); 2960 STAILQ_INSERT_TAIL(&sc->ti_cdata.ti_txbusyq, txd, tx_q); 2961 txd->tx_m = m; 2962 sc->ti_txcnt += nseg; 2963 2964 return (0); 2965} 2966 2967static void 2968ti_start(struct ifnet *ifp) 2969{ 2970 struct ti_softc *sc; 2971 2972 sc = ifp->if_softc; 2973 TI_LOCK(sc); 2974 ti_start_locked(ifp); 2975 TI_UNLOCK(sc); 2976} 2977 2978/* 2979 * Main transmit routine. To avoid having to do mbuf copies, we put pointers 2980 * to the mbuf data regions directly in the transmit descriptors. 2981 */ 2982static void 2983ti_start_locked(struct ifnet *ifp) 2984{ 2985 struct ti_softc *sc; 2986 struct mbuf *m_head = NULL; 2987 int enq = 0; 2988 2989 sc = ifp->if_softc; 2990 2991 for (; ifp->if_snd.ifq_head != NULL && 2992 sc->ti_txcnt < (TI_TX_RING_CNT - 16);) { 2993 IF_DEQUEUE(&ifp->if_snd, m_head); 2994 if (m_head == NULL) 2995 break; 2996 2997 /* 2998 * XXX 2999 * safety overkill. If this is a fragmented packet chain 3000 * with delayed TCP/UDP checksums, then only encapsulate 3001 * it if we have enough descriptors to handle the entire 3002 * chain at once. 3003 * (paranoia -- may not actually be needed) 3004 */ 3005 if (m_head->m_flags & M_FIRSTFRAG && 3006 m_head->m_pkthdr.csum_flags & (CSUM_DELAY_DATA)) { 3007 if ((TI_TX_RING_CNT - sc->ti_txcnt) < 3008 m_head->m_pkthdr.csum_data + 16) { 3009 IF_PREPEND(&ifp->if_snd, m_head); 3010 ifp->if_drv_flags |= IFF_DRV_OACTIVE; 3011 break; 3012 } 3013 } 3014 3015 /* 3016 * Pack the data into the transmit ring. If we 3017 * don't have room, set the OACTIVE flag and wait 3018 * for the NIC to drain the ring. 3019 */ 3020 if (ti_encap(sc, &m_head)) { 3021 if (m_head == NULL) 3022 break; 3023 IF_PREPEND(&ifp->if_snd, m_head); 3024 ifp->if_drv_flags |= IFF_DRV_OACTIVE; 3025 break; 3026 } 3027 3028 enq++; 3029 /* 3030 * If there's a BPF listener, bounce a copy of this frame 3031 * to him. 3032 */ 3033 ETHER_BPF_MTAP(ifp, m_head); 3034 } 3035 3036 if (enq > 0) { 3037 /* Transmit */ 3038 CSR_WRITE_4(sc, TI_MB_SENDPROD_IDX, sc->ti_tx_saved_prodidx); 3039 3040 /* 3041 * Set a timeout in case the chip goes out to lunch. 3042 */ 3043 sc->ti_timer = 5; 3044 } 3045} 3046 3047static void 3048ti_init(void *xsc) 3049{ 3050 struct ti_softc *sc; 3051 3052 sc = xsc; 3053 TI_LOCK(sc); 3054 ti_init_locked(sc); 3055 TI_UNLOCK(sc); 3056} 3057 3058static void 3059ti_init_locked(void *xsc) 3060{ 3061 struct ti_softc *sc = xsc; 3062 3063 /* Cancel pending I/O and flush buffers. */ 3064 ti_stop(sc); 3065 3066 /* Init the gen info block, ring control blocks and firmware. */ 3067 if (ti_gibinit(sc)) { 3068 device_printf(sc->ti_dev, "initialization failure\n"); 3069 return; 3070 } 3071} 3072 3073static void ti_init2(struct ti_softc *sc) 3074{ 3075 struct ti_cmd_desc cmd; 3076 struct ifnet *ifp; 3077 uint8_t *ea; 3078 struct ifmedia *ifm; 3079 int tmp; 3080 3081 TI_LOCK_ASSERT(sc); 3082 3083 ifp = sc->ti_ifp; 3084 3085 /* Specify MTU and interface index. */ 3086 CSR_WRITE_4(sc, TI_GCR_IFINDEX, sc->ti_unit); 3087 CSR_WRITE_4(sc, TI_GCR_IFMTU, ifp->if_mtu + 3088 ETHER_HDR_LEN + ETHER_CRC_LEN + ETHER_VLAN_ENCAP_LEN); 3089 TI_DO_CMD(TI_CMD_UPDATE_GENCOM, 0, 0); 3090 3091 /* Load our MAC address. */ 3092 ea = IF_LLADDR(sc->ti_ifp); 3093 CSR_WRITE_4(sc, TI_GCR_PAR0, (ea[0] << 8) | ea[1]); 3094 CSR_WRITE_4(sc, TI_GCR_PAR1, 3095 (ea[2] << 24) | (ea[3] << 16) | (ea[4] << 8) | ea[5]); 3096 TI_DO_CMD(TI_CMD_SET_MAC_ADDR, 0, 0); 3097 3098 /* Enable or disable promiscuous mode as needed. */ 3099 if (ifp->if_flags & IFF_PROMISC) { 3100 TI_DO_CMD(TI_CMD_SET_PROMISC_MODE, TI_CMD_CODE_PROMISC_ENB, 0); 3101 } else { 3102 TI_DO_CMD(TI_CMD_SET_PROMISC_MODE, TI_CMD_CODE_PROMISC_DIS, 0); 3103 } 3104 3105 /* Program multicast filter. */ 3106 ti_setmulti(sc); 3107 3108 /* 3109 * If this is a Tigon 1, we should tell the 3110 * firmware to use software packet filtering. 3111 */ 3112 if (sc->ti_hwrev == TI_HWREV_TIGON) { 3113 TI_DO_CMD(TI_CMD_FDR_FILTERING, TI_CMD_CODE_FILT_ENB, 0); 3114 } 3115 3116 /* Init RX ring. */ 3117 ti_init_rx_ring_std(sc); 3118 3119 /* Init jumbo RX ring. */ 3120 if (ifp->if_mtu > (ETHERMTU + ETHER_HDR_LEN + ETHER_CRC_LEN)) 3121 ti_init_rx_ring_jumbo(sc); 3122 3123 /* 3124 * If this is a Tigon 2, we can also configure the 3125 * mini ring. 3126 */ 3127 if (sc->ti_hwrev == TI_HWREV_TIGON_II) 3128 ti_init_rx_ring_mini(sc); 3129 3130 CSR_WRITE_4(sc, TI_GCR_RXRETURNCONS_IDX, 0); 3131 sc->ti_rx_saved_considx = 0; 3132 3133 /* Init TX ring. */ 3134 ti_init_tx_ring(sc); 3135 3136 /* Tell firmware we're alive. */ 3137 TI_DO_CMD(TI_CMD_HOST_STATE, TI_CMD_CODE_STACK_UP, 0); 3138 3139 /* Enable host interrupts. */ 3140 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 0); 3141 3142 ifp->if_drv_flags |= IFF_DRV_RUNNING; 3143 ifp->if_drv_flags &= ~IFF_DRV_OACTIVE; 3144 callout_reset(&sc->ti_watchdog, hz, ti_watchdog, sc); 3145 3146 /* 3147 * Make sure to set media properly. We have to do this 3148 * here since we have to issue commands in order to set 3149 * the link negotiation and we can't issue commands until 3150 * the firmware is running. 3151 */ 3152 ifm = &sc->ifmedia; 3153 tmp = ifm->ifm_media; 3154 ifm->ifm_media = ifm->ifm_cur->ifm_media; 3155 ti_ifmedia_upd(ifp); 3156 ifm->ifm_media = tmp; 3157} 3158 3159/* 3160 * Set media options. 3161 */ 3162static int 3163ti_ifmedia_upd(struct ifnet *ifp) 3164{ 3165 struct ti_softc *sc; 3166 struct ifmedia *ifm; 3167 struct ti_cmd_desc cmd; 3168 uint32_t flowctl; 3169 3170 sc = ifp->if_softc; 3171 ifm = &sc->ifmedia; 3172 3173 if (IFM_TYPE(ifm->ifm_media) != IFM_ETHER) 3174 return (EINVAL); 3175 3176 flowctl = 0; 3177 3178 switch (IFM_SUBTYPE(ifm->ifm_media)) { 3179 case IFM_AUTO: 3180 /* 3181 * Transmit flow control doesn't work on the Tigon 1. 3182 */ 3183 flowctl = TI_GLNK_RX_FLOWCTL_Y; 3184 3185 /* 3186 * Transmit flow control can also cause problems on the 3187 * Tigon 2, apparantly with both the copper and fiber 3188 * boards. The symptom is that the interface will just 3189 * hang. This was reproduced with Alteon 180 switches. 3190 */ 3191#if 0 3192 if (sc->ti_hwrev != TI_HWREV_TIGON) 3193 flowctl |= TI_GLNK_TX_FLOWCTL_Y; 3194#endif 3195 3196 CSR_WRITE_4(sc, TI_GCR_GLINK, TI_GLNK_PREF|TI_GLNK_1000MB| 3197 TI_GLNK_FULL_DUPLEX| flowctl | 3198 TI_GLNK_AUTONEGENB|TI_GLNK_ENB); 3199 3200 flowctl = TI_LNK_RX_FLOWCTL_Y; 3201#if 0 3202 if (sc->ti_hwrev != TI_HWREV_TIGON) 3203 flowctl |= TI_LNK_TX_FLOWCTL_Y; 3204#endif 3205 3206 CSR_WRITE_4(sc, TI_GCR_LINK, TI_LNK_100MB|TI_LNK_10MB| 3207 TI_LNK_FULL_DUPLEX|TI_LNK_HALF_DUPLEX| flowctl | 3208 TI_LNK_AUTONEGENB|TI_LNK_ENB); 3209 TI_DO_CMD(TI_CMD_LINK_NEGOTIATION, 3210 TI_CMD_CODE_NEGOTIATE_BOTH, 0); 3211 break; 3212 case IFM_1000_SX: 3213 case IFM_1000_T: 3214 flowctl = TI_GLNK_RX_FLOWCTL_Y; 3215#if 0 3216 if (sc->ti_hwrev != TI_HWREV_TIGON) 3217 flowctl |= TI_GLNK_TX_FLOWCTL_Y; 3218#endif 3219 3220 CSR_WRITE_4(sc, TI_GCR_GLINK, TI_GLNK_PREF|TI_GLNK_1000MB| 3221 flowctl |TI_GLNK_ENB); 3222 CSR_WRITE_4(sc, TI_GCR_LINK, 0); 3223 if ((ifm->ifm_media & IFM_GMASK) == IFM_FDX) { 3224 TI_SETBIT(sc, TI_GCR_GLINK, TI_GLNK_FULL_DUPLEX); 3225 } 3226 TI_DO_CMD(TI_CMD_LINK_NEGOTIATION, 3227 TI_CMD_CODE_NEGOTIATE_GIGABIT, 0); 3228 break; 3229 case IFM_100_FX: 3230 case IFM_10_FL: 3231 case IFM_100_TX: 3232 case IFM_10_T: 3233 flowctl = TI_LNK_RX_FLOWCTL_Y; 3234#if 0 3235 if (sc->ti_hwrev != TI_HWREV_TIGON) 3236 flowctl |= TI_LNK_TX_FLOWCTL_Y; 3237#endif 3238 3239 CSR_WRITE_4(sc, TI_GCR_GLINK, 0); 3240 CSR_WRITE_4(sc, TI_GCR_LINK, TI_LNK_ENB|TI_LNK_PREF|flowctl); 3241 if (IFM_SUBTYPE(ifm->ifm_media) == IFM_100_FX || 3242 IFM_SUBTYPE(ifm->ifm_media) == IFM_100_TX) { 3243 TI_SETBIT(sc, TI_GCR_LINK, TI_LNK_100MB); 3244 } else { 3245 TI_SETBIT(sc, TI_GCR_LINK, TI_LNK_10MB); 3246 } 3247 if ((ifm->ifm_media & IFM_GMASK) == IFM_FDX) { 3248 TI_SETBIT(sc, TI_GCR_LINK, TI_LNK_FULL_DUPLEX); 3249 } else { 3250 TI_SETBIT(sc, TI_GCR_LINK, TI_LNK_HALF_DUPLEX); 3251 } 3252 TI_DO_CMD(TI_CMD_LINK_NEGOTIATION, 3253 TI_CMD_CODE_NEGOTIATE_10_100, 0); 3254 break; 3255 } 3256 3257 return (0); 3258} 3259 3260/* 3261 * Report current media status. 3262 */ 3263static void 3264ti_ifmedia_sts(struct ifnet *ifp, struct ifmediareq *ifmr) 3265{ 3266 struct ti_softc *sc; 3267 uint32_t media = 0; 3268 3269 sc = ifp->if_softc; 3270 3271 ifmr->ifm_status = IFM_AVALID; 3272 ifmr->ifm_active = IFM_ETHER; 3273 3274 if (sc->ti_linkstat == TI_EV_CODE_LINK_DOWN) 3275 return; 3276 3277 ifmr->ifm_status |= IFM_ACTIVE; 3278 3279 if (sc->ti_linkstat == TI_EV_CODE_GIG_LINK_UP) { 3280 media = CSR_READ_4(sc, TI_GCR_GLINK_STAT); 3281 if (sc->ti_copper) 3282 ifmr->ifm_active |= IFM_1000_T; 3283 else 3284 ifmr->ifm_active |= IFM_1000_SX; 3285 if (media & TI_GLNK_FULL_DUPLEX) 3286 ifmr->ifm_active |= IFM_FDX; 3287 else 3288 ifmr->ifm_active |= IFM_HDX; 3289 } else if (sc->ti_linkstat == TI_EV_CODE_LINK_UP) { 3290 media = CSR_READ_4(sc, TI_GCR_LINK_STAT); 3291 if (sc->ti_copper) { 3292 if (media & TI_LNK_100MB) 3293 ifmr->ifm_active |= IFM_100_TX; 3294 if (media & TI_LNK_10MB) 3295 ifmr->ifm_active |= IFM_10_T; 3296 } else { 3297 if (media & TI_LNK_100MB) 3298 ifmr->ifm_active |= IFM_100_FX; 3299 if (media & TI_LNK_10MB) 3300 ifmr->ifm_active |= IFM_10_FL; 3301 } 3302 if (media & TI_LNK_FULL_DUPLEX) 3303 ifmr->ifm_active |= IFM_FDX; 3304 if (media & TI_LNK_HALF_DUPLEX) 3305 ifmr->ifm_active |= IFM_HDX; 3306 } 3307} 3308 3309static int 3310ti_ioctl(struct ifnet *ifp, u_long command, caddr_t data) 3311{ 3312 struct ti_softc *sc = ifp->if_softc; 3313 struct ifreq *ifr = (struct ifreq *) data; 3314 struct ti_cmd_desc cmd; 3315 int mask, error = 0; 3316 3317 switch (command) { 3318 case SIOCSIFMTU: 3319 TI_LOCK(sc); 3320 if (ifr->ifr_mtu > TI_JUMBO_MTU) 3321 error = EINVAL; 3322 else { 3323 ifp->if_mtu = ifr->ifr_mtu; 3324 ti_init_locked(sc); 3325 } 3326 TI_UNLOCK(sc); 3327 break; 3328 case SIOCSIFFLAGS: 3329 TI_LOCK(sc); 3330 if (ifp->if_flags & IFF_UP) { 3331 /* 3332 * If only the state of the PROMISC flag changed, 3333 * then just use the 'set promisc mode' command 3334 * instead of reinitializing the entire NIC. Doing 3335 * a full re-init means reloading the firmware and 3336 * waiting for it to start up, which may take a 3337 * second or two. 3338 */ 3339 if (ifp->if_drv_flags & IFF_DRV_RUNNING && 3340 ifp->if_flags & IFF_PROMISC && 3341 !(sc->ti_if_flags & IFF_PROMISC)) { 3342 TI_DO_CMD(TI_CMD_SET_PROMISC_MODE, 3343 TI_CMD_CODE_PROMISC_ENB, 0); 3344 } else if (ifp->if_drv_flags & IFF_DRV_RUNNING && 3345 !(ifp->if_flags & IFF_PROMISC) && 3346 sc->ti_if_flags & IFF_PROMISC) { 3347 TI_DO_CMD(TI_CMD_SET_PROMISC_MODE, 3348 TI_CMD_CODE_PROMISC_DIS, 0); 3349 } else 3350 ti_init_locked(sc); 3351 } else { 3352 if (ifp->if_drv_flags & IFF_DRV_RUNNING) { 3353 ti_stop(sc); 3354 } 3355 } 3356 sc->ti_if_flags = ifp->if_flags; 3357 TI_UNLOCK(sc); 3358 break; 3359 case SIOCADDMULTI: 3360 case SIOCDELMULTI: 3361 TI_LOCK(sc); 3362 if (ifp->if_drv_flags & IFF_DRV_RUNNING) 3363 ti_setmulti(sc); 3364 TI_UNLOCK(sc); 3365 break; 3366 case SIOCSIFMEDIA: 3367 case SIOCGIFMEDIA: 3368 error = ifmedia_ioctl(ifp, ifr, &sc->ifmedia, command); 3369 break; 3370 case SIOCSIFCAP: 3371 TI_LOCK(sc); 3372 mask = ifr->ifr_reqcap ^ ifp->if_capenable; 3373 if (mask & IFCAP_HWCSUM) { 3374 if (IFCAP_HWCSUM & ifp->if_capenable) 3375 ifp->if_capenable &= ~IFCAP_HWCSUM; 3376 else 3377 ifp->if_capenable |= IFCAP_HWCSUM; 3378 if (ifp->if_drv_flags & IFF_DRV_RUNNING) 3379 ti_init_locked(sc); 3380 } 3381 TI_UNLOCK(sc); 3382 break; 3383 default: 3384 error = ether_ioctl(ifp, command, data); 3385 break; 3386 } 3387 3388 return (error); 3389} 3390 3391static int 3392ti_open(struct cdev *dev, int flags, int fmt, struct thread *td) 3393{ 3394 struct ti_softc *sc; 3395 3396 sc = dev->si_drv1; 3397 if (sc == NULL) 3398 return (ENODEV); 3399 3400 TI_LOCK(sc); 3401 sc->ti_flags |= TI_FLAG_DEBUGING; 3402 TI_UNLOCK(sc); 3403 3404 return (0); 3405} 3406 3407static int 3408ti_close(struct cdev *dev, int flag, int fmt, struct thread *td) 3409{ 3410 struct ti_softc *sc; 3411 3412 sc = dev->si_drv1; 3413 if (sc == NULL) 3414 return (ENODEV); 3415 3416 TI_LOCK(sc); 3417 sc->ti_flags &= ~TI_FLAG_DEBUGING; 3418 TI_UNLOCK(sc); 3419 3420 return (0); 3421} 3422 3423/* 3424 * This ioctl routine goes along with the Tigon character device. 3425 */ 3426static int 3427ti_ioctl2(struct cdev *dev, u_long cmd, caddr_t addr, int flag, 3428 struct thread *td) 3429{ 3430 struct ti_softc *sc; 3431 int error; 3432 3433 sc = dev->si_drv1; 3434 if (sc == NULL) 3435 return (ENODEV); 3436 3437 error = 0; 3438 3439 switch (cmd) { 3440 case TIIOCGETSTATS: 3441 { 3442 struct ti_stats *outstats; 3443 3444 outstats = (struct ti_stats *)addr; 3445 3446 TI_LOCK(sc); 3447 bcopy(&sc->ti_rdata->ti_info.ti_stats, outstats, 3448 sizeof(struct ti_stats)); 3449 TI_UNLOCK(sc); 3450 break; 3451 } 3452 case TIIOCGETPARAMS: 3453 { 3454 struct ti_params *params; 3455 3456 params = (struct ti_params *)addr; 3457 3458 TI_LOCK(sc); 3459 params->ti_stat_ticks = sc->ti_stat_ticks; 3460 params->ti_rx_coal_ticks = sc->ti_rx_coal_ticks; 3461 params->ti_tx_coal_ticks = sc->ti_tx_coal_ticks; 3462 params->ti_rx_max_coal_bds = sc->ti_rx_max_coal_bds; 3463 params->ti_tx_max_coal_bds = sc->ti_tx_max_coal_bds; 3464 params->ti_tx_buf_ratio = sc->ti_tx_buf_ratio; 3465 params->param_mask = TI_PARAM_ALL; 3466 TI_UNLOCK(sc); 3467 3468 error = 0; 3469 3470 break; 3471 } 3472 case TIIOCSETPARAMS: 3473 { 3474 struct ti_params *params; 3475 3476 params = (struct ti_params *)addr; 3477 3478 TI_LOCK(sc); 3479 if (params->param_mask & TI_PARAM_STAT_TICKS) { 3480 sc->ti_stat_ticks = params->ti_stat_ticks; 3481 CSR_WRITE_4(sc, TI_GCR_STAT_TICKS, sc->ti_stat_ticks); 3482 } 3483 3484 if (params->param_mask & TI_PARAM_RX_COAL_TICKS) { 3485 sc->ti_rx_coal_ticks = params->ti_rx_coal_ticks; 3486 CSR_WRITE_4(sc, TI_GCR_RX_COAL_TICKS, 3487 sc->ti_rx_coal_ticks); 3488 } 3489 3490 if (params->param_mask & TI_PARAM_TX_COAL_TICKS) { 3491 sc->ti_tx_coal_ticks = params->ti_tx_coal_ticks; 3492 CSR_WRITE_4(sc, TI_GCR_TX_COAL_TICKS, 3493 sc->ti_tx_coal_ticks); 3494 } 3495 3496 if (params->param_mask & TI_PARAM_RX_COAL_BDS) { 3497 sc->ti_rx_max_coal_bds = params->ti_rx_max_coal_bds; 3498 CSR_WRITE_4(sc, TI_GCR_RX_MAX_COAL_BD, 3499 sc->ti_rx_max_coal_bds); 3500 } 3501 3502 if (params->param_mask & TI_PARAM_TX_COAL_BDS) { 3503 sc->ti_tx_max_coal_bds = params->ti_tx_max_coal_bds; 3504 CSR_WRITE_4(sc, TI_GCR_TX_MAX_COAL_BD, 3505 sc->ti_tx_max_coal_bds); 3506 } 3507 3508 if (params->param_mask & TI_PARAM_TX_BUF_RATIO) { 3509 sc->ti_tx_buf_ratio = params->ti_tx_buf_ratio; 3510 CSR_WRITE_4(sc, TI_GCR_TX_BUFFER_RATIO, 3511 sc->ti_tx_buf_ratio); 3512 } 3513 TI_UNLOCK(sc); 3514 3515 error = 0; 3516 3517 break; 3518 } 3519 case TIIOCSETTRACE: { 3520 ti_trace_type trace_type; 3521 3522 trace_type = *(ti_trace_type *)addr; 3523 3524 /* 3525 * Set tracing to whatever the user asked for. Setting 3526 * this register to 0 should have the effect of disabling 3527 * tracing. 3528 */ 3529 CSR_WRITE_4(sc, TI_GCR_NIC_TRACING, trace_type); 3530 3531 error = 0; 3532 3533 break; 3534 } 3535 case TIIOCGETTRACE: { 3536 struct ti_trace_buf *trace_buf; 3537 uint32_t trace_start, cur_trace_ptr, trace_len; 3538 3539 trace_buf = (struct ti_trace_buf *)addr; 3540 3541 TI_LOCK(sc); 3542 trace_start = CSR_READ_4(sc, TI_GCR_NICTRACE_START); 3543 cur_trace_ptr = CSR_READ_4(sc, TI_GCR_NICTRACE_PTR); 3544 trace_len = CSR_READ_4(sc, TI_GCR_NICTRACE_LEN); 3545 3546#if 0 3547 if_printf(sc->ti_ifp, "trace_start = %#x, cur_trace_ptr = %#x, " 3548 "trace_len = %d\n", trace_start, 3549 cur_trace_ptr, trace_len); 3550 if_printf(sc->ti_ifp, "trace_buf->buf_len = %d\n", 3551 trace_buf->buf_len); 3552#endif 3553 3554 error = ti_copy_mem(sc, trace_start, min(trace_len, 3555 trace_buf->buf_len), 3556 (caddr_t)trace_buf->buf, 1, 1); 3557 3558 if (error == 0) { 3559 trace_buf->fill_len = min(trace_len, 3560 trace_buf->buf_len); 3561 if (cur_trace_ptr < trace_start) 3562 trace_buf->cur_trace_ptr = 3563 trace_start - cur_trace_ptr; 3564 else 3565 trace_buf->cur_trace_ptr = 3566 cur_trace_ptr - trace_start; 3567 } else 3568 trace_buf->fill_len = 0; 3569 TI_UNLOCK(sc); 3570 3571 break; 3572 } 3573 3574 /* 3575 * For debugging, five ioctls are needed: 3576 * ALT_ATTACH 3577 * ALT_READ_TG_REG 3578 * ALT_WRITE_TG_REG 3579 * ALT_READ_TG_MEM 3580 * ALT_WRITE_TG_MEM 3581 */ 3582 case ALT_ATTACH: 3583 /* 3584 * From what I can tell, Alteon's Solaris Tigon driver 3585 * only has one character device, so you have to attach 3586 * to the Tigon board you're interested in. This seems 3587 * like a not-so-good way to do things, since unless you 3588 * subsequently specify the unit number of the device 3589 * you're interested in every ioctl, you'll only be 3590 * able to debug one board at a time. 3591 */ 3592 error = 0; 3593 break; 3594 case ALT_READ_TG_MEM: 3595 case ALT_WRITE_TG_MEM: 3596 { 3597 struct tg_mem *mem_param; 3598 uint32_t sram_end, scratch_end; 3599 3600 mem_param = (struct tg_mem *)addr; 3601 3602 if (sc->ti_hwrev == TI_HWREV_TIGON) { 3603 sram_end = TI_END_SRAM_I; 3604 scratch_end = TI_END_SCRATCH_I; 3605 } else { 3606 sram_end = TI_END_SRAM_II; 3607 scratch_end = TI_END_SCRATCH_II; 3608 } 3609 3610 /* 3611 * For now, we'll only handle accessing regular SRAM, 3612 * nothing else. 3613 */ 3614 TI_LOCK(sc); 3615 if ((mem_param->tgAddr >= TI_BEG_SRAM) 3616 && ((mem_param->tgAddr + mem_param->len) <= sram_end)) { 3617 /* 3618 * In this instance, we always copy to/from user 3619 * space, so the user space argument is set to 1. 3620 */ 3621 error = ti_copy_mem(sc, mem_param->tgAddr, 3622 mem_param->len, 3623 mem_param->userAddr, 1, 3624 (cmd == ALT_READ_TG_MEM) ? 1 : 0); 3625 } else if ((mem_param->tgAddr >= TI_BEG_SCRATCH) 3626 && (mem_param->tgAddr <= scratch_end)) { 3627 error = ti_copy_scratch(sc, mem_param->tgAddr, 3628 mem_param->len, 3629 mem_param->userAddr, 1, 3630 (cmd == ALT_READ_TG_MEM) ? 3631 1 : 0, TI_PROCESSOR_A); 3632 } else if ((mem_param->tgAddr >= TI_BEG_SCRATCH_B_DEBUG) 3633 && (mem_param->tgAddr <= TI_BEG_SCRATCH_B_DEBUG)) { 3634 if (sc->ti_hwrev == TI_HWREV_TIGON) { 3635 if_printf(sc->ti_ifp, 3636 "invalid memory range for Tigon I\n"); 3637 error = EINVAL; 3638 break; 3639 } 3640 error = ti_copy_scratch(sc, mem_param->tgAddr - 3641 TI_SCRATCH_DEBUG_OFF, 3642 mem_param->len, 3643 mem_param->userAddr, 1, 3644 (cmd == ALT_READ_TG_MEM) ? 3645 1 : 0, TI_PROCESSOR_B); 3646 } else { 3647 if_printf(sc->ti_ifp, "memory address %#x len %d is " 3648 "out of supported range\n", 3649 mem_param->tgAddr, mem_param->len); 3650 error = EINVAL; 3651 } 3652 TI_UNLOCK(sc); 3653 3654 break; 3655 } 3656 case ALT_READ_TG_REG: 3657 case ALT_WRITE_TG_REG: 3658 { 3659 struct tg_reg *regs; 3660 uint32_t tmpval; 3661 3662 regs = (struct tg_reg *)addr; 3663 3664 /* 3665 * Make sure the address in question isn't out of range. 3666 */ 3667 if (regs->addr > TI_REG_MAX) { 3668 error = EINVAL; 3669 break; 3670 } 3671 TI_LOCK(sc); 3672 if (cmd == ALT_READ_TG_REG) { 3673 bus_space_read_region_4(sc->ti_btag, sc->ti_bhandle, 3674 regs->addr, &tmpval, 1); 3675 regs->data = ntohl(tmpval); 3676#if 0 3677 if ((regs->addr == TI_CPU_STATE) 3678 || (regs->addr == TI_CPU_CTL_B)) { 3679 if_printf(sc->ti_ifp, "register %#x = %#x\n", 3680 regs->addr, tmpval); 3681 } 3682#endif 3683 } else { 3684 tmpval = htonl(regs->data); 3685 bus_space_write_region_4(sc->ti_btag, sc->ti_bhandle, 3686 regs->addr, &tmpval, 1); 3687 } 3688 TI_UNLOCK(sc); 3689 3690 break; 3691 } 3692 default: 3693 error = ENOTTY; 3694 break; 3695 } 3696 return (error); 3697} 3698 3699static void 3700ti_watchdog(void *arg) 3701{ 3702 struct ti_softc *sc; 3703 struct ifnet *ifp; 3704 3705 sc = arg; 3706 TI_LOCK_ASSERT(sc); 3707 callout_reset(&sc->ti_watchdog, hz, ti_watchdog, sc); 3708 if (sc->ti_timer == 0 || --sc->ti_timer > 0) 3709 return; 3710 3711 /* 3712 * When we're debugging, the chip is often stopped for long periods 3713 * of time, and that would normally cause the watchdog timer to fire. 3714 * Since that impedes debugging, we don't want to do that. 3715 */ 3716 if (sc->ti_flags & TI_FLAG_DEBUGING) 3717 return; 3718 3719 ifp = sc->ti_ifp; 3720 if_printf(ifp, "watchdog timeout -- resetting\n"); 3721 ti_stop(sc); 3722 ti_init_locked(sc); 3723 3724 ifp->if_oerrors++; 3725} 3726 3727/* 3728 * Stop the adapter and free any mbufs allocated to the 3729 * RX and TX lists. 3730 */ 3731static void 3732ti_stop(struct ti_softc *sc) 3733{ 3734 struct ifnet *ifp; 3735 struct ti_cmd_desc cmd; 3736 3737 TI_LOCK_ASSERT(sc); 3738 3739 ifp = sc->ti_ifp; 3740 3741 /* Disable host interrupts. */ 3742 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 1); 3743 /* 3744 * Tell firmware we're shutting down. 3745 */ 3746 TI_DO_CMD(TI_CMD_HOST_STATE, TI_CMD_CODE_STACK_DOWN, 0); 3747 3748 /* Halt and reinitialize. */ 3749 if (ti_chipinit(sc) != 0) 3750 return; 3751 ti_mem_zero(sc, 0x2000, 0x100000 - 0x2000); 3752 if (ti_chipinit(sc) != 0) 3753 return; 3754 3755 /* Free the RX lists. */ 3756 ti_free_rx_ring_std(sc); 3757 3758 /* Free jumbo RX list. */ 3759 ti_free_rx_ring_jumbo(sc); 3760 3761 /* Free mini RX list. */ 3762 ti_free_rx_ring_mini(sc); 3763 3764 /* Free TX buffers. */ 3765 ti_free_tx_ring(sc); 3766 3767 sc->ti_ev_prodidx.ti_idx = 0; 3768 sc->ti_return_prodidx.ti_idx = 0; 3769 sc->ti_tx_considx.ti_idx = 0; 3770 sc->ti_tx_saved_considx = TI_TXCONS_UNSET; 3771 3772 ifp->if_drv_flags &= ~(IFF_DRV_RUNNING | IFF_DRV_OACTIVE); 3773 callout_stop(&sc->ti_watchdog); 3774} 3775 3776/* 3777 * Stop all chip I/O so that the kernel's probe routines don't 3778 * get confused by errant DMAs when rebooting. 3779 */ 3780static int 3781ti_shutdown(device_t dev) 3782{ 3783 struct ti_softc *sc; 3784 3785 sc = device_get_softc(dev); 3786 TI_LOCK(sc); 3787 ti_chipinit(sc); 3788 TI_UNLOCK(sc); 3789 3790 return (0); 3791} 3792