Searched hist:253691 (Results 1 - 9 of 9) sorted by relevance
| /freebsd-11-stable/sys/dev/cxgbe/ | ||
| H A D | t4_tracer.c | 253691 Fri Jul 26 20:11:14 MDT 2013 np Add support for packet-sniffing tracers to cxgbe(4). This works with all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and for general purpose monitoring without tapping any cxgbe or cxl ifnet directly. Tracers on the T4/T5 chips provide access to Ethernet frames exactly as they were received from or transmitted on the wire. On transmit, a tracer will capture a frame after TSO segmentation, hw VLAN tag insertion, hw L3 & L4 checksum insertion, etc. It will also capture frames generated by the TCP offload engine (TOE traffic is normally invisible to the kernel). On receive, a tracer will capture a frame before hw VLAN extraction, runt filtering, other badness filtering, before the steering/drop/L2-rewrite filters or the TOE have had a go at it, and of course before sw LRO in the driver. There are 4 tracers on a chip. A tracer can trace only in one direction (tx or rx). For now cxgbetool will set up tracers to capture the first 128B of every transmitted or received frame on a given port. This is a small subset of what the hardware can do. A pseudo ifnet with the same name as the nexus driver (t4nex0 or t5nex0) will be created for tracing. The data delivered to this ifnet is an additional copy made inside the chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual. /* watch cxl0, which is the first port hanging off t5nex0. */ # cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting) # cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving) # cxgbetool t5nex0 tracer list # tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K "frames" with no L3/L4 checksum but this will show you the frames that were actually transmitted. /* all done */ # cxgbetool t5nex0 tracer 0 disable # cxgbetool t5nex0 tracer 1 disable # cxgbetool t5nex0 tracer list # ifconfig t5nex0 destroy |
| H A D | t4_ioctl.h | diff 253691 Fri Jul 26 20:11:14 MDT 2013 np Add support for packet-sniffing tracers to cxgbe(4). This works with all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and for general purpose monitoring without tapping any cxgbe or cxl ifnet directly. Tracers on the T4/T5 chips provide access to Ethernet frames exactly as they were received from or transmitted on the wire. On transmit, a tracer will capture a frame after TSO segmentation, hw VLAN tag insertion, hw L3 & L4 checksum insertion, etc. It will also capture frames generated by the TCP offload engine (TOE traffic is normally invisible to the kernel). On receive, a tracer will capture a frame before hw VLAN extraction, runt filtering, other badness filtering, before the steering/drop/L2-rewrite filters or the TOE have had a go at it, and of course before sw LRO in the driver. There are 4 tracers on a chip. A tracer can trace only in one direction (tx or rx). For now cxgbetool will set up tracers to capture the first 128B of every transmitted or received frame on a given port. This is a small subset of what the hardware can do. A pseudo ifnet with the same name as the nexus driver (t4nex0 or t5nex0) will be created for tracing. The data delivered to this ifnet is an additional copy made inside the chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual. /* watch cxl0, which is the first port hanging off t5nex0. */ # cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting) # cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving) # cxgbetool t5nex0 tracer list # tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K "frames" with no L3/L4 checksum but this will show you the frames that were actually transmitted. /* all done */ # cxgbetool t5nex0 tracer 0 disable # cxgbetool t5nex0 tracer 1 disable # cxgbetool t5nex0 tracer list # ifconfig t5nex0 destroy |
| H A D | adapter.h | diff 253691 Fri Jul 26 20:11:14 MDT 2013 np Add support for packet-sniffing tracers to cxgbe(4). This works with all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and for general purpose monitoring without tapping any cxgbe or cxl ifnet directly. Tracers on the T4/T5 chips provide access to Ethernet frames exactly as they were received from or transmitted on the wire. On transmit, a tracer will capture a frame after TSO segmentation, hw VLAN tag insertion, hw L3 & L4 checksum insertion, etc. It will also capture frames generated by the TCP offload engine (TOE traffic is normally invisible to the kernel). On receive, a tracer will capture a frame before hw VLAN extraction, runt filtering, other badness filtering, before the steering/drop/L2-rewrite filters or the TOE have had a go at it, and of course before sw LRO in the driver. There are 4 tracers on a chip. A tracer can trace only in one direction (tx or rx). For now cxgbetool will set up tracers to capture the first 128B of every transmitted or received frame on a given port. This is a small subset of what the hardware can do. A pseudo ifnet with the same name as the nexus driver (t4nex0 or t5nex0) will be created for tracing. The data delivered to this ifnet is an additional copy made inside the chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual. /* watch cxl0, which is the first port hanging off t5nex0. */ # cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting) # cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving) # cxgbetool t5nex0 tracer list # tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K "frames" with no L3/L4 checksum but this will show you the frames that were actually transmitted. /* all done */ # cxgbetool t5nex0 tracer 0 disable # cxgbetool t5nex0 tracer 1 disable # cxgbetool t5nex0 tracer list # ifconfig t5nex0 destroy |
| H A D | t4_sge.c | diff 253691 Fri Jul 26 20:11:14 MDT 2013 np Add support for packet-sniffing tracers to cxgbe(4). This works with all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and for general purpose monitoring without tapping any cxgbe or cxl ifnet directly. Tracers on the T4/T5 chips provide access to Ethernet frames exactly as they were received from or transmitted on the wire. On transmit, a tracer will capture a frame after TSO segmentation, hw VLAN tag insertion, hw L3 & L4 checksum insertion, etc. It will also capture frames generated by the TCP offload engine (TOE traffic is normally invisible to the kernel). On receive, a tracer will capture a frame before hw VLAN extraction, runt filtering, other badness filtering, before the steering/drop/L2-rewrite filters or the TOE have had a go at it, and of course before sw LRO in the driver. There are 4 tracers on a chip. A tracer can trace only in one direction (tx or rx). For now cxgbetool will set up tracers to capture the first 128B of every transmitted or received frame on a given port. This is a small subset of what the hardware can do. A pseudo ifnet with the same name as the nexus driver (t4nex0 or t5nex0) will be created for tracing. The data delivered to this ifnet is an additional copy made inside the chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual. /* watch cxl0, which is the first port hanging off t5nex0. */ # cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting) # cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving) # cxgbetool t5nex0 tracer list # tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K "frames" with no L3/L4 checksum but this will show you the frames that were actually transmitted. /* all done */ # cxgbetool t5nex0 tracer 0 disable # cxgbetool t5nex0 tracer 1 disable # cxgbetool t5nex0 tracer list # ifconfig t5nex0 destroy |
| H A D | t4_main.c | diff 253691 Fri Jul 26 20:11:14 MDT 2013 np Add support for packet-sniffing tracers to cxgbe(4). This works with all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and for general purpose monitoring without tapping any cxgbe or cxl ifnet directly. Tracers on the T4/T5 chips provide access to Ethernet frames exactly as they were received from or transmitted on the wire. On transmit, a tracer will capture a frame after TSO segmentation, hw VLAN tag insertion, hw L3 & L4 checksum insertion, etc. It will also capture frames generated by the TCP offload engine (TOE traffic is normally invisible to the kernel). On receive, a tracer will capture a frame before hw VLAN extraction, runt filtering, other badness filtering, before the steering/drop/L2-rewrite filters or the TOE have had a go at it, and of course before sw LRO in the driver. There are 4 tracers on a chip. A tracer can trace only in one direction (tx or rx). For now cxgbetool will set up tracers to capture the first 128B of every transmitted or received frame on a given port. This is a small subset of what the hardware can do. A pseudo ifnet with the same name as the nexus driver (t4nex0 or t5nex0) will be created for tracing. The data delivered to this ifnet is an additional copy made inside the chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual. /* watch cxl0, which is the first port hanging off t5nex0. */ # cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting) # cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving) # cxgbetool t5nex0 tracer list # tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K "frames" with no L3/L4 checksum but this will show you the frames that were actually transmitted. /* all done */ # cxgbetool t5nex0 tracer 0 disable # cxgbetool t5nex0 tracer 1 disable # cxgbetool t5nex0 tracer list # ifconfig t5nex0 destroy |
| /freebsd-11-stable/sys/dev/cxgbe/common/ | ||
| H A D | t4_hw.h | diff 253691 Fri Jul 26 20:11:14 MDT 2013 np Add support for packet-sniffing tracers to cxgbe(4). This works with all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and for general purpose monitoring without tapping any cxgbe or cxl ifnet directly. Tracers on the T4/T5 chips provide access to Ethernet frames exactly as they were received from or transmitted on the wire. On transmit, a tracer will capture a frame after TSO segmentation, hw VLAN tag insertion, hw L3 & L4 checksum insertion, etc. It will also capture frames generated by the TCP offload engine (TOE traffic is normally invisible to the kernel). On receive, a tracer will capture a frame before hw VLAN extraction, runt filtering, other badness filtering, before the steering/drop/L2-rewrite filters or the TOE have had a go at it, and of course before sw LRO in the driver. There are 4 tracers on a chip. A tracer can trace only in one direction (tx or rx). For now cxgbetool will set up tracers to capture the first 128B of every transmitted or received frame on a given port. This is a small subset of what the hardware can do. A pseudo ifnet with the same name as the nexus driver (t4nex0 or t5nex0) will be created for tracing. The data delivered to this ifnet is an additional copy made inside the chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual. /* watch cxl0, which is the first port hanging off t5nex0. */ # cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting) # cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving) # cxgbetool t5nex0 tracer list # tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K "frames" with no L3/L4 checksum but this will show you the frames that were actually transmitted. /* all done */ # cxgbetool t5nex0 tracer 0 disable # cxgbetool t5nex0 tracer 1 disable # cxgbetool t5nex0 tracer list # ifconfig t5nex0 destroy |
| H A D | t4_hw.c | diff 253691 Fri Jul 26 20:11:14 MDT 2013 np Add support for packet-sniffing tracers to cxgbe(4). This works with all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and for general purpose monitoring without tapping any cxgbe or cxl ifnet directly. Tracers on the T4/T5 chips provide access to Ethernet frames exactly as they were received from or transmitted on the wire. On transmit, a tracer will capture a frame after TSO segmentation, hw VLAN tag insertion, hw L3 & L4 checksum insertion, etc. It will also capture frames generated by the TCP offload engine (TOE traffic is normally invisible to the kernel). On receive, a tracer will capture a frame before hw VLAN extraction, runt filtering, other badness filtering, before the steering/drop/L2-rewrite filters or the TOE have had a go at it, and of course before sw LRO in the driver. There are 4 tracers on a chip. A tracer can trace only in one direction (tx or rx). For now cxgbetool will set up tracers to capture the first 128B of every transmitted or received frame on a given port. This is a small subset of what the hardware can do. A pseudo ifnet with the same name as the nexus driver (t4nex0 or t5nex0) will be created for tracing. The data delivered to this ifnet is an additional copy made inside the chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual. /* watch cxl0, which is the first port hanging off t5nex0. */ # cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting) # cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving) # cxgbetool t5nex0 tracer list # tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K "frames" with no L3/L4 checksum but this will show you the frames that were actually transmitted. /* all done */ # cxgbetool t5nex0 tracer 0 disable # cxgbetool t5nex0 tracer 1 disable # cxgbetool t5nex0 tracer list # ifconfig t5nex0 destroy |
| /freebsd-11-stable/sys/modules/cxgbe/if_cxgbe/ | ||
| H A D | Makefile | diff 253691 Fri Jul 26 20:11:14 MDT 2013 np Add support for packet-sniffing tracers to cxgbe(4). This works with all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and for general purpose monitoring without tapping any cxgbe or cxl ifnet directly. Tracers on the T4/T5 chips provide access to Ethernet frames exactly as they were received from or transmitted on the wire. On transmit, a tracer will capture a frame after TSO segmentation, hw VLAN tag insertion, hw L3 & L4 checksum insertion, etc. It will also capture frames generated by the TCP offload engine (TOE traffic is normally invisible to the kernel). On receive, a tracer will capture a frame before hw VLAN extraction, runt filtering, other badness filtering, before the steering/drop/L2-rewrite filters or the TOE have had a go at it, and of course before sw LRO in the driver. There are 4 tracers on a chip. A tracer can trace only in one direction (tx or rx). For now cxgbetool will set up tracers to capture the first 128B of every transmitted or received frame on a given port. This is a small subset of what the hardware can do. A pseudo ifnet with the same name as the nexus driver (t4nex0 or t5nex0) will be created for tracing. The data delivered to this ifnet is an additional copy made inside the chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual. /* watch cxl0, which is the first port hanging off t5nex0. */ # cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting) # cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving) # cxgbetool t5nex0 tracer list # tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K "frames" with no L3/L4 checksum but this will show you the frames that were actually transmitted. /* all done */ # cxgbetool t5nex0 tracer 0 disable # cxgbetool t5nex0 tracer 1 disable # cxgbetool t5nex0 tracer list # ifconfig t5nex0 destroy |
| /freebsd-11-stable/usr.sbin/cxgbetool/ | ||
| H A D | cxgbetool.c | diff 253691 Fri Jul 26 22:11:14 MDT 2013 np Add support for packet-sniffing tracers to cxgbe(4). This works with all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and for general purpose monitoring without tapping any cxgbe or cxl ifnet directly. Tracers on the T4/T5 chips provide access to Ethernet frames exactly as they were received from or transmitted on the wire. On transmit, a tracer will capture a frame after TSO segmentation, hw VLAN tag insertion, hw L3 & L4 checksum insertion, etc. It will also capture frames generated by the TCP offload engine (TOE traffic is normally invisible to the kernel). On receive, a tracer will capture a frame before hw VLAN extraction, runt filtering, other badness filtering, before the steering/drop/L2-rewrite filters or the TOE have had a go at it, and of course before sw LRO in the driver. There are 4 tracers on a chip. A tracer can trace only in one direction (tx or rx). For now cxgbetool will set up tracers to capture the first 128B of every transmitted or received frame on a given port. This is a small subset of what the hardware can do. A pseudo ifnet with the same name as the nexus driver (t4nex0 or t5nex0) will be created for tracing. The data delivered to this ifnet is an additional copy made inside the chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual. /* watch cxl0, which is the first port hanging off t5nex0. */ # cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting) # cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving) # cxgbetool t5nex0 tracer list # tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K "frames" with no L3/L4 checksum but this will show you the frames that were actually transmitted. /* all done */ # cxgbetool t5nex0 tracer 0 disable # cxgbetool t5nex0 tracer 1 disable # cxgbetool t5nex0 tracer list # ifconfig t5nex0 destroy |
Completed in 378 milliseconds