Searched hist:238869 (Results 1 - 12 of 12) sorted by relevance
| /freebsd-11-stable/sys/dev/isp/ | ||
| H A D | isp_stds.h | diff 238869 Sat Jul 28 18:09:56 MDT 2012 mjacob ----------- MISC CHANGES Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee eventual delivery of a NOTIFY ACK. This is tons better than just ignoring the return from isp_notify_ack and hoping for the best. Clean up the lower level lun enable code to be a bit more sensible. Fix a botch in isp_endcmd which was messing up the sense data. Fix notify ack for SRR to use a sensible error code in the case of a reject. Clean up and make clear what kind of firmware we've loaded and what capabilities it has. ----------- FULL (252 byte) SENSE DATA In CTIOs for the ISP, there's only a limimted amount of space to load SENSE DATA for associated CHECK CONDITIONS (24 or 26 bytes). This makes it difficult to send full SENSE DATA that can be up to 252 bytes. Implement MODE 2 responses which have us build the FCP Response in system memory which the ISP will put onto the wire directly. On the initiator side, the same problem occurs in that a command status response only has a limited amount of space for SENSE DATA. This data is supplemented by status continuation responses that the ISP pushes onto the response queue after the status response. We now pull them all together so that full sense data can be returned to the periph driver. This is supported on 23XX, 24XX and 25XX cards. This is also preparation for doing >16 byte CDBs. ----------- FC TAPE Implement full FC-TAPE on both initiator and target mode side. This capability is driven by firmware loaded, board type, board NVRAM settings, or hint configuration options to enable or disable. This is supported for 23XX, 24XX and 25XX cards. On the initiator side, we pretty much just have to generate a command reference number for each command we send out. This is FCP-4 compliant in that we do this per ITL nexus to generate the allowed 1 thru 255 CRN. In order to support the target side of FC-TAPE, we now pay attention to more of the PRLI word 3 parameters which will tell us whether an initiator wants confirmed responses. While we're at it, we'll pay attention to the initiator view too and report it. On sending back CTIOs, we will notice whether the initiator wants confirmed responses and we'll set up flags to do so. If a response or data frame is lost the initiator sends us an SRR (Sequence Retransmit Request) ELS which shows up as an SRR notify and all outstanding CTIOs are nuked with SRR Received status. The SRR notify contains the offset that the initiator wants us to restart the data transfer from or to retransmit the response frame. If the ISP driver still has the CCB around for which the data segment or response applies, it will retransmit. However, we typically don't know about a lost data frame until we send the FCP Response and the initiator totes up counters for data moved and notices missing segments. In this case we've already completed the data CCBs already and sent themn back up to the periph driver. Because there's no really clean mechanism yet in CAM to handle this, a hack has been put into place to complete the CTIO CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA POINTER extended message in it. The internal ISP target groks this and ctl(8) will be modified to deal with this as well. At any rate, the data is retransmitted and an an FCP response is sent. The whole point here is to successfully complete a command so that you don't have to depend on ULP (SCSI) to have to recover, which in the case of tape is not really possible (hence the name FC-TAPE). Sponsored by: Spectralogic MFC after: 1 month |
| H A D | isp_library.h | diff 238869 Sat Jul 28 18:09:56 MDT 2012 mjacob ----------- MISC CHANGES Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee eventual delivery of a NOTIFY ACK. This is tons better than just ignoring the return from isp_notify_ack and hoping for the best. Clean up the lower level lun enable code to be a bit more sensible. Fix a botch in isp_endcmd which was messing up the sense data. Fix notify ack for SRR to use a sensible error code in the case of a reject. Clean up and make clear what kind of firmware we've loaded and what capabilities it has. ----------- FULL (252 byte) SENSE DATA In CTIOs for the ISP, there's only a limimted amount of space to load SENSE DATA for associated CHECK CONDITIONS (24 or 26 bytes). This makes it difficult to send full SENSE DATA that can be up to 252 bytes. Implement MODE 2 responses which have us build the FCP Response in system memory which the ISP will put onto the wire directly. On the initiator side, the same problem occurs in that a command status response only has a limited amount of space for SENSE DATA. This data is supplemented by status continuation responses that the ISP pushes onto the response queue after the status response. We now pull them all together so that full sense data can be returned to the periph driver. This is supported on 23XX, 24XX and 25XX cards. This is also preparation for doing >16 byte CDBs. ----------- FC TAPE Implement full FC-TAPE on both initiator and target mode side. This capability is driven by firmware loaded, board type, board NVRAM settings, or hint configuration options to enable or disable. This is supported for 23XX, 24XX and 25XX cards. On the initiator side, we pretty much just have to generate a command reference number for each command we send out. This is FCP-4 compliant in that we do this per ITL nexus to generate the allowed 1 thru 255 CRN. In order to support the target side of FC-TAPE, we now pay attention to more of the PRLI word 3 parameters which will tell us whether an initiator wants confirmed responses. While we're at it, we'll pay attention to the initiator view too and report it. On sending back CTIOs, we will notice whether the initiator wants confirmed responses and we'll set up flags to do so. If a response or data frame is lost the initiator sends us an SRR (Sequence Retransmit Request) ELS which shows up as an SRR notify and all outstanding CTIOs are nuked with SRR Received status. The SRR notify contains the offset that the initiator wants us to restart the data transfer from or to retransmit the response frame. If the ISP driver still has the CCB around for which the data segment or response applies, it will retransmit. However, we typically don't know about a lost data frame until we send the FCP Response and the initiator totes up counters for data moved and notices missing segments. In this case we've already completed the data CCBs already and sent themn back up to the periph driver. Because there's no really clean mechanism yet in CAM to handle this, a hack has been put into place to complete the CTIO CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA POINTER extended message in it. The internal ISP target groks this and ctl(8) will be modified to deal with this as well. At any rate, the data is retransmitted and an an FCP response is sent. The whole point here is to successfully complete a command so that you don't have to depend on ULP (SCSI) to have to recover, which in the case of tape is not really possible (hence the name FC-TAPE). Sponsored by: Spectralogic MFC after: 1 month |
| H A D | isp_pci.c | diff 239218 Sun Aug 12 19:00:53 MDT 2012 mjacob Fix an oops where we wiped out DMA maps. Don't allocate extended command space for anything less than a 2300. MFC after: 1 month X-MFC: 238869 diff 239010 Fri Aug 03 12:38:07 MDT 2012 mjacob Oops. We only do allocate room for extended commands and responses for 2300 cards are newer. Sponsored by: Spectralogic Noticed by: Our Friend Manfred MFC after: 1 month X-MFC: 238869 diff 238869 Sat Jul 28 18:09:56 MDT 2012 mjacob ----------- MISC CHANGES Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee eventual delivery of a NOTIFY ACK. This is tons better than just ignoring the return from isp_notify_ack and hoping for the best. Clean up the lower level lun enable code to be a bit more sensible. Fix a botch in isp_endcmd which was messing up the sense data. Fix notify ack for SRR to use a sensible error code in the case of a reject. Clean up and make clear what kind of firmware we've loaded and what capabilities it has. ----------- FULL (252 byte) SENSE DATA In CTIOs for the ISP, there's only a limimted amount of space to load SENSE DATA for associated CHECK CONDITIONS (24 or 26 bytes). This makes it difficult to send full SENSE DATA that can be up to 252 bytes. Implement MODE 2 responses which have us build the FCP Response in system memory which the ISP will put onto the wire directly. On the initiator side, the same problem occurs in that a command status response only has a limited amount of space for SENSE DATA. This data is supplemented by status continuation responses that the ISP pushes onto the response queue after the status response. We now pull them all together so that full sense data can be returned to the periph driver. This is supported on 23XX, 24XX and 25XX cards. This is also preparation for doing >16 byte CDBs. ----------- FC TAPE Implement full FC-TAPE on both initiator and target mode side. This capability is driven by firmware loaded, board type, board NVRAM settings, or hint configuration options to enable or disable. This is supported for 23XX, 24XX and 25XX cards. On the initiator side, we pretty much just have to generate a command reference number for each command we send out. This is FCP-4 compliant in that we do this per ITL nexus to generate the allowed 1 thru 255 CRN. In order to support the target side of FC-TAPE, we now pay attention to more of the PRLI word 3 parameters which will tell us whether an initiator wants confirmed responses. While we're at it, we'll pay attention to the initiator view too and report it. On sending back CTIOs, we will notice whether the initiator wants confirmed responses and we'll set up flags to do so. If a response or data frame is lost the initiator sends us an SRR (Sequence Retransmit Request) ELS which shows up as an SRR notify and all outstanding CTIOs are nuked with SRR Received status. The SRR notify contains the offset that the initiator wants us to restart the data transfer from or to retransmit the response frame. If the ISP driver still has the CCB around for which the data segment or response applies, it will retransmit. However, we typically don't know about a lost data frame until we send the FCP Response and the initiator totes up counters for data moved and notices missing segments. In this case we've already completed the data CCBs already and sent themn back up to the periph driver. Because there's no really clean mechanism yet in CAM to handle this, a hack has been put into place to complete the CTIO CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA POINTER extended message in it. The internal ISP target groks this and ctl(8) will be modified to deal with this as well. At any rate, the data is retransmitted and an an FCP response is sent. The whole point here is to successfully complete a command so that you don't have to depend on ULP (SCSI) to have to recover, which in the case of tape is not really possible (hence the name FC-TAPE). Sponsored by: Spectralogic MFC after: 1 month |
| H A D | isp_target.c | diff 238869 Sat Jul 28 18:09:56 MDT 2012 mjacob ----------- MISC CHANGES Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee eventual delivery of a NOTIFY ACK. This is tons better than just ignoring the return from isp_notify_ack and hoping for the best. Clean up the lower level lun enable code to be a bit more sensible. Fix a botch in isp_endcmd which was messing up the sense data. Fix notify ack for SRR to use a sensible error code in the case of a reject. Clean up and make clear what kind of firmware we've loaded and what capabilities it has. ----------- FULL (252 byte) SENSE DATA In CTIOs for the ISP, there's only a limimted amount of space to load SENSE DATA for associated CHECK CONDITIONS (24 or 26 bytes). This makes it difficult to send full SENSE DATA that can be up to 252 bytes. Implement MODE 2 responses which have us build the FCP Response in system memory which the ISP will put onto the wire directly. On the initiator side, the same problem occurs in that a command status response only has a limited amount of space for SENSE DATA. This data is supplemented by status continuation responses that the ISP pushes onto the response queue after the status response. We now pull them all together so that full sense data can be returned to the periph driver. This is supported on 23XX, 24XX and 25XX cards. This is also preparation for doing >16 byte CDBs. ----------- FC TAPE Implement full FC-TAPE on both initiator and target mode side. This capability is driven by firmware loaded, board type, board NVRAM settings, or hint configuration options to enable or disable. This is supported for 23XX, 24XX and 25XX cards. On the initiator side, we pretty much just have to generate a command reference number for each command we send out. This is FCP-4 compliant in that we do this per ITL nexus to generate the allowed 1 thru 255 CRN. In order to support the target side of FC-TAPE, we now pay attention to more of the PRLI word 3 parameters which will tell us whether an initiator wants confirmed responses. While we're at it, we'll pay attention to the initiator view too and report it. On sending back CTIOs, we will notice whether the initiator wants confirmed responses and we'll set up flags to do so. If a response or data frame is lost the initiator sends us an SRR (Sequence Retransmit Request) ELS which shows up as an SRR notify and all outstanding CTIOs are nuked with SRR Received status. The SRR notify contains the offset that the initiator wants us to restart the data transfer from or to retransmit the response frame. If the ISP driver still has the CCB around for which the data segment or response applies, it will retransmit. However, we typically don't know about a lost data frame until we send the FCP Response and the initiator totes up counters for data moved and notices missing segments. In this case we've already completed the data CCBs already and sent themn back up to the periph driver. Because there's no really clean mechanism yet in CAM to handle this, a hack has been put into place to complete the CTIO CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA POINTER extended message in it. The internal ISP target groks this and ctl(8) will be modified to deal with this as well. At any rate, the data is retransmitted and an an FCP response is sent. The whole point here is to successfully complete a command so that you don't have to depend on ULP (SCSI) to have to recover, which in the case of tape is not really possible (hence the name FC-TAPE). Sponsored by: Spectralogic MFC after: 1 month |
| H A D | isp_sbus.c | diff 238887 Sun Jul 29 12:22:33 MDT 2012 mjacob Grr.!$()!$$ I missed checking this in even though I *did* run a tinderbox myself and caught the error. Change to isp_send_cmd needs a final ecmd argument. Sponsored by: Spectralogic MFC after: 1 month X-MFC: 238869 |
| H A D | isp_target.h | diff 238869 Sat Jul 28 18:09:56 MDT 2012 mjacob ----------- MISC CHANGES Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee eventual delivery of a NOTIFY ACK. This is tons better than just ignoring the return from isp_notify_ack and hoping for the best. Clean up the lower level lun enable code to be a bit more sensible. Fix a botch in isp_endcmd which was messing up the sense data. Fix notify ack for SRR to use a sensible error code in the case of a reject. Clean up and make clear what kind of firmware we've loaded and what capabilities it has. ----------- FULL (252 byte) SENSE DATA In CTIOs for the ISP, there's only a limimted amount of space to load SENSE DATA for associated CHECK CONDITIONS (24 or 26 bytes). This makes it difficult to send full SENSE DATA that can be up to 252 bytes. Implement MODE 2 responses which have us build the FCP Response in system memory which the ISP will put onto the wire directly. On the initiator side, the same problem occurs in that a command status response only has a limited amount of space for SENSE DATA. This data is supplemented by status continuation responses that the ISP pushes onto the response queue after the status response. We now pull them all together so that full sense data can be returned to the periph driver. This is supported on 23XX, 24XX and 25XX cards. This is also preparation for doing >16 byte CDBs. ----------- FC TAPE Implement full FC-TAPE on both initiator and target mode side. This capability is driven by firmware loaded, board type, board NVRAM settings, or hint configuration options to enable or disable. This is supported for 23XX, 24XX and 25XX cards. On the initiator side, we pretty much just have to generate a command reference number for each command we send out. This is FCP-4 compliant in that we do this per ITL nexus to generate the allowed 1 thru 255 CRN. In order to support the target side of FC-TAPE, we now pay attention to more of the PRLI word 3 parameters which will tell us whether an initiator wants confirmed responses. While we're at it, we'll pay attention to the initiator view too and report it. On sending back CTIOs, we will notice whether the initiator wants confirmed responses and we'll set up flags to do so. If a response or data frame is lost the initiator sends us an SRR (Sequence Retransmit Request) ELS which shows up as an SRR notify and all outstanding CTIOs are nuked with SRR Received status. The SRR notify contains the offset that the initiator wants us to restart the data transfer from or to retransmit the response frame. If the ISP driver still has the CCB around for which the data segment or response applies, it will retransmit. However, we typically don't know about a lost data frame until we send the FCP Response and the initiator totes up counters for data moved and notices missing segments. In this case we've already completed the data CCBs already and sent themn back up to the periph driver. Because there's no really clean mechanism yet in CAM to handle this, a hack has been put into place to complete the CTIO CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA POINTER extended message in it. The internal ISP target groks this and ctl(8) will be modified to deal with this as well. At any rate, the data is retransmitted and an an FCP response is sent. The whole point here is to successfully complete a command so that you don't have to depend on ULP (SCSI) to have to recover, which in the case of tape is not really possible (hence the name FC-TAPE). Sponsored by: Spectralogic MFC after: 1 month |
| H A D | isp_library.c | diff 238869 Sat Jul 28 18:09:56 MDT 2012 mjacob ----------- MISC CHANGES Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee eventual delivery of a NOTIFY ACK. This is tons better than just ignoring the return from isp_notify_ack and hoping for the best. Clean up the lower level lun enable code to be a bit more sensible. Fix a botch in isp_endcmd which was messing up the sense data. Fix notify ack for SRR to use a sensible error code in the case of a reject. Clean up and make clear what kind of firmware we've loaded and what capabilities it has. ----------- FULL (252 byte) SENSE DATA In CTIOs for the ISP, there's only a limimted amount of space to load SENSE DATA for associated CHECK CONDITIONS (24 or 26 bytes). This makes it difficult to send full SENSE DATA that can be up to 252 bytes. Implement MODE 2 responses which have us build the FCP Response in system memory which the ISP will put onto the wire directly. On the initiator side, the same problem occurs in that a command status response only has a limited amount of space for SENSE DATA. This data is supplemented by status continuation responses that the ISP pushes onto the response queue after the status response. We now pull them all together so that full sense data can be returned to the periph driver. This is supported on 23XX, 24XX and 25XX cards. This is also preparation for doing >16 byte CDBs. ----------- FC TAPE Implement full FC-TAPE on both initiator and target mode side. This capability is driven by firmware loaded, board type, board NVRAM settings, or hint configuration options to enable or disable. This is supported for 23XX, 24XX and 25XX cards. On the initiator side, we pretty much just have to generate a command reference number for each command we send out. This is FCP-4 compliant in that we do this per ITL nexus to generate the allowed 1 thru 255 CRN. In order to support the target side of FC-TAPE, we now pay attention to more of the PRLI word 3 parameters which will tell us whether an initiator wants confirmed responses. While we're at it, we'll pay attention to the initiator view too and report it. On sending back CTIOs, we will notice whether the initiator wants confirmed responses and we'll set up flags to do so. If a response or data frame is lost the initiator sends us an SRR (Sequence Retransmit Request) ELS which shows up as an SRR notify and all outstanding CTIOs are nuked with SRR Received status. The SRR notify contains the offset that the initiator wants us to restart the data transfer from or to retransmit the response frame. If the ISP driver still has the CCB around for which the data segment or response applies, it will retransmit. However, we typically don't know about a lost data frame until we send the FCP Response and the initiator totes up counters for data moved and notices missing segments. In this case we've already completed the data CCBs already and sent themn back up to the periph driver. Because there's no really clean mechanism yet in CAM to handle this, a hack has been put into place to complete the CTIO CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA POINTER extended message in it. The internal ISP target groks this and ctl(8) will be modified to deal with this as well. At any rate, the data is retransmitted and an an FCP response is sent. The whole point here is to successfully complete a command so that you don't have to depend on ULP (SCSI) to have to recover, which in the case of tape is not really possible (hence the name FC-TAPE). Sponsored by: Spectralogic MFC after: 1 month |
| H A D | ispmbox.h | diff 238869 Sat Jul 28 18:09:56 MDT 2012 mjacob ----------- MISC CHANGES Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee eventual delivery of a NOTIFY ACK. This is tons better than just ignoring the return from isp_notify_ack and hoping for the best. Clean up the lower level lun enable code to be a bit more sensible. Fix a botch in isp_endcmd which was messing up the sense data. Fix notify ack for SRR to use a sensible error code in the case of a reject. Clean up and make clear what kind of firmware we've loaded and what capabilities it has. ----------- FULL (252 byte) SENSE DATA In CTIOs for the ISP, there's only a limimted amount of space to load SENSE DATA for associated CHECK CONDITIONS (24 or 26 bytes). This makes it difficult to send full SENSE DATA that can be up to 252 bytes. Implement MODE 2 responses which have us build the FCP Response in system memory which the ISP will put onto the wire directly. On the initiator side, the same problem occurs in that a command status response only has a limited amount of space for SENSE DATA. This data is supplemented by status continuation responses that the ISP pushes onto the response queue after the status response. We now pull them all together so that full sense data can be returned to the periph driver. This is supported on 23XX, 24XX and 25XX cards. This is also preparation for doing >16 byte CDBs. ----------- FC TAPE Implement full FC-TAPE on both initiator and target mode side. This capability is driven by firmware loaded, board type, board NVRAM settings, or hint configuration options to enable or disable. This is supported for 23XX, 24XX and 25XX cards. On the initiator side, we pretty much just have to generate a command reference number for each command we send out. This is FCP-4 compliant in that we do this per ITL nexus to generate the allowed 1 thru 255 CRN. In order to support the target side of FC-TAPE, we now pay attention to more of the PRLI word 3 parameters which will tell us whether an initiator wants confirmed responses. While we're at it, we'll pay attention to the initiator view too and report it. On sending back CTIOs, we will notice whether the initiator wants confirmed responses and we'll set up flags to do so. If a response or data frame is lost the initiator sends us an SRR (Sequence Retransmit Request) ELS which shows up as an SRR notify and all outstanding CTIOs are nuked with SRR Received status. The SRR notify contains the offset that the initiator wants us to restart the data transfer from or to retransmit the response frame. If the ISP driver still has the CCB around for which the data segment or response applies, it will retransmit. However, we typically don't know about a lost data frame until we send the FCP Response and the initiator totes up counters for data moved and notices missing segments. In this case we've already completed the data CCBs already and sent themn back up to the periph driver. Because there's no really clean mechanism yet in CAM to handle this, a hack has been put into place to complete the CTIO CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA POINTER extended message in it. The internal ISP target groks this and ctl(8) will be modified to deal with this as well. At any rate, the data is retransmitted and an an FCP response is sent. The whole point here is to successfully complete a command so that you don't have to depend on ULP (SCSI) to have to recover, which in the case of tape is not really possible (hence the name FC-TAPE). Sponsored by: Spectralogic MFC after: 1 month |
| H A D | isp_freebsd.c | diff 239218 Sun Aug 12 19:00:53 MDT 2012 mjacob Fix an oops where we wiped out DMA maps. Don't allocate extended command space for anything less than a 2300. MFC after: 1 month X-MFC: 238869 diff 238869 Sat Jul 28 18:09:56 MDT 2012 mjacob ----------- MISC CHANGES Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee eventual delivery of a NOTIFY ACK. This is tons better than just ignoring the return from isp_notify_ack and hoping for the best. Clean up the lower level lun enable code to be a bit more sensible. Fix a botch in isp_endcmd which was messing up the sense data. Fix notify ack for SRR to use a sensible error code in the case of a reject. Clean up and make clear what kind of firmware we've loaded and what capabilities it has. ----------- FULL (252 byte) SENSE DATA In CTIOs for the ISP, there's only a limimted amount of space to load SENSE DATA for associated CHECK CONDITIONS (24 or 26 bytes). This makes it difficult to send full SENSE DATA that can be up to 252 bytes. Implement MODE 2 responses which have us build the FCP Response in system memory which the ISP will put onto the wire directly. On the initiator side, the same problem occurs in that a command status response only has a limited amount of space for SENSE DATA. This data is supplemented by status continuation responses that the ISP pushes onto the response queue after the status response. We now pull them all together so that full sense data can be returned to the periph driver. This is supported on 23XX, 24XX and 25XX cards. This is also preparation for doing >16 byte CDBs. ----------- FC TAPE Implement full FC-TAPE on both initiator and target mode side. This capability is driven by firmware loaded, board type, board NVRAM settings, or hint configuration options to enable or disable. This is supported for 23XX, 24XX and 25XX cards. On the initiator side, we pretty much just have to generate a command reference number for each command we send out. This is FCP-4 compliant in that we do this per ITL nexus to generate the allowed 1 thru 255 CRN. In order to support the target side of FC-TAPE, we now pay attention to more of the PRLI word 3 parameters which will tell us whether an initiator wants confirmed responses. While we're at it, we'll pay attention to the initiator view too and report it. On sending back CTIOs, we will notice whether the initiator wants confirmed responses and we'll set up flags to do so. If a response or data frame is lost the initiator sends us an SRR (Sequence Retransmit Request) ELS which shows up as an SRR notify and all outstanding CTIOs are nuked with SRR Received status. The SRR notify contains the offset that the initiator wants us to restart the data transfer from or to retransmit the response frame. If the ISP driver still has the CCB around for which the data segment or response applies, it will retransmit. However, we typically don't know about a lost data frame until we send the FCP Response and the initiator totes up counters for data moved and notices missing segments. In this case we've already completed the data CCBs already and sent themn back up to the periph driver. Because there's no really clean mechanism yet in CAM to handle this, a hack has been put into place to complete the CTIO CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA POINTER extended message in it. The internal ISP target groks this and ctl(8) will be modified to deal with this as well. At any rate, the data is retransmitted and an an FCP response is sent. The whole point here is to successfully complete a command so that you don't have to depend on ULP (SCSI) to have to recover, which in the case of tape is not really possible (hence the name FC-TAPE). Sponsored by: Spectralogic MFC after: 1 month |
| H A D | isp_freebsd.h | diff 238869 Sat Jul 28 18:09:56 MDT 2012 mjacob ----------- MISC CHANGES Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee eventual delivery of a NOTIFY ACK. This is tons better than just ignoring the return from isp_notify_ack and hoping for the best. Clean up the lower level lun enable code to be a bit more sensible. Fix a botch in isp_endcmd which was messing up the sense data. Fix notify ack for SRR to use a sensible error code in the case of a reject. Clean up and make clear what kind of firmware we've loaded and what capabilities it has. ----------- FULL (252 byte) SENSE DATA In CTIOs for the ISP, there's only a limimted amount of space to load SENSE DATA for associated CHECK CONDITIONS (24 or 26 bytes). This makes it difficult to send full SENSE DATA that can be up to 252 bytes. Implement MODE 2 responses which have us build the FCP Response in system memory which the ISP will put onto the wire directly. On the initiator side, the same problem occurs in that a command status response only has a limited amount of space for SENSE DATA. This data is supplemented by status continuation responses that the ISP pushes onto the response queue after the status response. We now pull them all together so that full sense data can be returned to the periph driver. This is supported on 23XX, 24XX and 25XX cards. This is also preparation for doing >16 byte CDBs. ----------- FC TAPE Implement full FC-TAPE on both initiator and target mode side. This capability is driven by firmware loaded, board type, board NVRAM settings, or hint configuration options to enable or disable. This is supported for 23XX, 24XX and 25XX cards. On the initiator side, we pretty much just have to generate a command reference number for each command we send out. This is FCP-4 compliant in that we do this per ITL nexus to generate the allowed 1 thru 255 CRN. In order to support the target side of FC-TAPE, we now pay attention to more of the PRLI word 3 parameters which will tell us whether an initiator wants confirmed responses. While we're at it, we'll pay attention to the initiator view too and report it. On sending back CTIOs, we will notice whether the initiator wants confirmed responses and we'll set up flags to do so. If a response or data frame is lost the initiator sends us an SRR (Sequence Retransmit Request) ELS which shows up as an SRR notify and all outstanding CTIOs are nuked with SRR Received status. The SRR notify contains the offset that the initiator wants us to restart the data transfer from or to retransmit the response frame. If the ISP driver still has the CCB around for which the data segment or response applies, it will retransmit. However, we typically don't know about a lost data frame until we send the FCP Response and the initiator totes up counters for data moved and notices missing segments. In this case we've already completed the data CCBs already and sent themn back up to the periph driver. Because there's no really clean mechanism yet in CAM to handle this, a hack has been put into place to complete the CTIO CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA POINTER extended message in it. The internal ISP target groks this and ctl(8) will be modified to deal with this as well. At any rate, the data is retransmitted and an an FCP response is sent. The whole point here is to successfully complete a command so that you don't have to depend on ULP (SCSI) to have to recover, which in the case of tape is not really possible (hence the name FC-TAPE). Sponsored by: Spectralogic MFC after: 1 month |
| H A D | ispvar.h | diff 238869 Sat Jul 28 18:09:56 MDT 2012 mjacob ----------- MISC CHANGES Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee eventual delivery of a NOTIFY ACK. This is tons better than just ignoring the return from isp_notify_ack and hoping for the best. Clean up the lower level lun enable code to be a bit more sensible. Fix a botch in isp_endcmd which was messing up the sense data. Fix notify ack for SRR to use a sensible error code in the case of a reject. Clean up and make clear what kind of firmware we've loaded and what capabilities it has. ----------- FULL (252 byte) SENSE DATA In CTIOs for the ISP, there's only a limimted amount of space to load SENSE DATA for associated CHECK CONDITIONS (24 or 26 bytes). This makes it difficult to send full SENSE DATA that can be up to 252 bytes. Implement MODE 2 responses which have us build the FCP Response in system memory which the ISP will put onto the wire directly. On the initiator side, the same problem occurs in that a command status response only has a limited amount of space for SENSE DATA. This data is supplemented by status continuation responses that the ISP pushes onto the response queue after the status response. We now pull them all together so that full sense data can be returned to the periph driver. This is supported on 23XX, 24XX and 25XX cards. This is also preparation for doing >16 byte CDBs. ----------- FC TAPE Implement full FC-TAPE on both initiator and target mode side. This capability is driven by firmware loaded, board type, board NVRAM settings, or hint configuration options to enable or disable. This is supported for 23XX, 24XX and 25XX cards. On the initiator side, we pretty much just have to generate a command reference number for each command we send out. This is FCP-4 compliant in that we do this per ITL nexus to generate the allowed 1 thru 255 CRN. In order to support the target side of FC-TAPE, we now pay attention to more of the PRLI word 3 parameters which will tell us whether an initiator wants confirmed responses. While we're at it, we'll pay attention to the initiator view too and report it. On sending back CTIOs, we will notice whether the initiator wants confirmed responses and we'll set up flags to do so. If a response or data frame is lost the initiator sends us an SRR (Sequence Retransmit Request) ELS which shows up as an SRR notify and all outstanding CTIOs are nuked with SRR Received status. The SRR notify contains the offset that the initiator wants us to restart the data transfer from or to retransmit the response frame. If the ISP driver still has the CCB around for which the data segment or response applies, it will retransmit. However, we typically don't know about a lost data frame until we send the FCP Response and the initiator totes up counters for data moved and notices missing segments. In this case we've already completed the data CCBs already and sent themn back up to the periph driver. Because there's no really clean mechanism yet in CAM to handle this, a hack has been put into place to complete the CTIO CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA POINTER extended message in it. The internal ISP target groks this and ctl(8) will be modified to deal with this as well. At any rate, the data is retransmitted and an an FCP response is sent. The whole point here is to successfully complete a command so that you don't have to depend on ULP (SCSI) to have to recover, which in the case of tape is not really possible (hence the name FC-TAPE). Sponsored by: Spectralogic MFC after: 1 month |
| H A D | isp.c | diff 238869 Sat Jul 28 18:09:56 MDT 2012 mjacob ----------- MISC CHANGES Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee eventual delivery of a NOTIFY ACK. This is tons better than just ignoring the return from isp_notify_ack and hoping for the best. Clean up the lower level lun enable code to be a bit more sensible. Fix a botch in isp_endcmd which was messing up the sense data. Fix notify ack for SRR to use a sensible error code in the case of a reject. Clean up and make clear what kind of firmware we've loaded and what capabilities it has. ----------- FULL (252 byte) SENSE DATA In CTIOs for the ISP, there's only a limimted amount of space to load SENSE DATA for associated CHECK CONDITIONS (24 or 26 bytes). This makes it difficult to send full SENSE DATA that can be up to 252 bytes. Implement MODE 2 responses which have us build the FCP Response in system memory which the ISP will put onto the wire directly. On the initiator side, the same problem occurs in that a command status response only has a limited amount of space for SENSE DATA. This data is supplemented by status continuation responses that the ISP pushes onto the response queue after the status response. We now pull them all together so that full sense data can be returned to the periph driver. This is supported on 23XX, 24XX and 25XX cards. This is also preparation for doing >16 byte CDBs. ----------- FC TAPE Implement full FC-TAPE on both initiator and target mode side. This capability is driven by firmware loaded, board type, board NVRAM settings, or hint configuration options to enable or disable. This is supported for 23XX, 24XX and 25XX cards. On the initiator side, we pretty much just have to generate a command reference number for each command we send out. This is FCP-4 compliant in that we do this per ITL nexus to generate the allowed 1 thru 255 CRN. In order to support the target side of FC-TAPE, we now pay attention to more of the PRLI word 3 parameters which will tell us whether an initiator wants confirmed responses. While we're at it, we'll pay attention to the initiator view too and report it. On sending back CTIOs, we will notice whether the initiator wants confirmed responses and we'll set up flags to do so. If a response or data frame is lost the initiator sends us an SRR (Sequence Retransmit Request) ELS which shows up as an SRR notify and all outstanding CTIOs are nuked with SRR Received status. The SRR notify contains the offset that the initiator wants us to restart the data transfer from or to retransmit the response frame. If the ISP driver still has the CCB around for which the data segment or response applies, it will retransmit. However, we typically don't know about a lost data frame until we send the FCP Response and the initiator totes up counters for data moved and notices missing segments. In this case we've already completed the data CCBs already and sent themn back up to the periph driver. Because there's no really clean mechanism yet in CAM to handle this, a hack has been put into place to complete the CTIO CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA POINTER extended message in it. The internal ISP target groks this and ctl(8) will be modified to deal with this as well. At any rate, the data is retransmitted and an an FCP response is sent. The whole point here is to successfully complete a command so that you don't have to depend on ULP (SCSI) to have to recover, which in the case of tape is not really possible (hence the name FC-TAPE). Sponsored by: Spectralogic MFC after: 1 month |
Completed in 1343 milliseconds