env: Use include/env for text-environment includes

The 'environment' word is too long. We mostly use 'env' in U-Boot, so use
that as the name of the include directory too.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

global: Migrate CONFIG_MAX_MEM_MAPPED to CFG

Perform a simple rename of CONFIG_MAX_MEM_MAPPED to CFG_MAX_MEM_MAPPED

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Remove unused CONFIG symbols

This removes the following unreferenced CONFIG symbols:
CONFIG_FDTADDR
CONFIG_FDTFILE
CONFIG_FLASH_SECTOR_SIZE
CONFIG_FSL_CPLD
CONFIG_HDMI_ENCODER_I2C_ADDR
CONFIG_I2C_MVTWSI
CONFIG_I2C_RTC_ADDR
CONFIG_IRAM_END
CONFIG_IRAM_SIZE
CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
CONFIG_L1_INIT_RAM
CONFIG_MACB_SEARCH_PHY
CONFIG_MIU_2BIT_21_7_INTERLEAVED
CONFIG_MTD_NAND_VERIFY_WRITE
CONFIG_MVGBE_PORTS
CONFIG_NETDEV
CONFIG_NUM_DSP_CPUS
CONFIG_PHY_BASE_ADR
CONFIG_PHY_INTERFACE_MODE
CONFIG_PSRAM_SCFG
CONFIG_RAMBOOT_SPIFLASH
CONFIG_RAMBOOT_TEXT_BASE
CONFIG_RD_LVL
CONFIG_ROCKCHIP_SDHCI_MAX_FREQ
CONFIG_SETUP_INITRD_TAG
CONFIG_SH_QSPI_BASE
CONFIG_SMDK5420
CONFIG_SOCRATES
CONFIG_SPI_ADDR
CONFIG_SPI_FLASH_QUAD
CONFIG_SPI_FLASH_SIZE
CONFIG_SPI_HALF_DUPLEX
CONFIG_SPI_N25Q256A_RESET
CONFIG_TEGRA_SLINK_CTRLS
CONFIG_TPM_TIS_BASE_ADDRESS
CONFIG_UBOOT_SECTOR_COUNT
CONFIG_UBOOT_SECTOR_START
CONFIG_VAR_SIZE_SPL
CONFIG_VERY_BIG_RAM

And also:
BL1_SIZE
PHY_NO
RESERVE_BLOCK_SIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_HSMMC2_8BIT to Kconfig

This converts the following to Kconfig:
CONFIG_HSMMC2_8BIT

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_IODELAY_RECALIBRATION to Kconfig

This converts the following to Kconfig:
CONFIG_IODELAY_RECALIBRATION

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Move remaining CONFIG_SYS_* to CFG_SYS_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_OMAP_ABE_SYSCK to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_OMAP_ABE_SYSCK

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_NS16550_* to CFG_SYS_NS16550_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_NAND_* to CFG_SYS_NAND_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_MAX_FLASH_SECT to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MAX_FLASH_SECT

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_SPL_KERNEL_OFFS to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_SPL_KERNEL_OFFS

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_FLASH_CFI_WIDTH to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_FLASH_CFI_WIDTH

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MONITOR_BASE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE

Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_NET_RETRY_COUNT to Kconfig

This converts the following to Kconfig:
CONFIG_NET_RETRY_COUNT

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SCSI_AHCI_PLAT et al to Kconfig

This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE

Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>

configs: Migrate CONFIG_SYS_MAX_FLASH_BANKS to Kconfig

Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

scripts: remove some configs in config_whitelist.txt

Remove some config finishing by _ badly added by
scripts/build-whitelist.sh when joker is used in comments.

for example:
doc/uImage.FIT/command_syntax_extensions.txt:
... #ifdef CONFIG_OF_* | ...

cmd/nvedit.c:# error Define one of CONFIG_ENV_IS_IN_{EEPROM| \
FLASH|MMC|FAT|EXT4|\

Remove also configs only used in comments:
- CONFIG_BOOGER in include/linux/kconfig.h
- CONFIG_COMMANDS
- CONFIG_INIT_IGNORE_ERROR
- CONFIG_REG_*
- CONFIG_HOTPLUG : drivers/watchdog/omap_wdt.c:18

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_NAND_OMAP_ECCSCHEME to Kconfig

The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_U_BOOT_LOCATIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_U_BOOT_LOCATIONS
CONFIG_SYS_NAND_U_BOOT_OFFS

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_ONFI_DETECTION to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_ONFI_DETECTION

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_5_ADDR_CYCLE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_5_ADDR_CYCLE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_BAD_BLOCK_POS to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS

In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_PAGE_COUNT to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_PAGE_COUNT

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_NAND_LOAD et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USB_XHCI_OMAP to Kconfig

This converts the following to Kconfig:
CONFIG_USB_XHCI_OMAP

Signed-off-by: Tom Rini <trini@konsulko.com>

usb: phy: ti: Remove non-DM PHY code

At this point in time, all platforms that had previously used
drivers/usb/phy/omap_usb_phy.c have been migrated to DM and related
options. Remove this now unused code and some related unused defines.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to Kconfig

- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

eeprom: Drop CONFIG_ENV_EEPROM_IS_ON_I2C usage

At this point in time, there's no systems with "U-Boot environment
exists on an EEPROM which is accessed over the I2C bus" that sets this
option. Drop it.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MMC_ENV_DEV et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART

Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: migrate CONFIG_SPL_LOAD_FIT_ADDRESS to defconfigs

Done with:
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS -H

Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: A few more migrations]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_SEND_HOSTNAME to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_SEND_HOSTNAME

Signed-off-by: Adam Ford <aford173@gmail.com>

Convert CONFIG_CMD_ASKENV et al to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_ASKENV
CONFIG_CMD_BMP
CONFIG_CMD_BOOTD
CONFIG_CMD_CACHE
CONFIG_CMD_CRC32
CONFIG_CMD_DHCP
CONFIG_CMD_ENV
CONFIG_CMD_EXPORTENV
CONFIG_CMD_EXT2
CONFIG_CMD_EXT4
CONFIG_CMD_FLASH
CONFIG_CMD_FS_GENERIC
CONFIG_CMD_FUSE
CONFIG_CMD_GPIO
CONFIG_CMD_GPT
CONFIG_CMD_GREPENV
CONFIG_CMD_I2C
CONFIG_CMD_IMLS
CONFIG_CMD_IMPORTENV
CONFIG_CMD_LOADB
CONFIG_CMD_LOADS
CONFIG_CMD_MEMINFO
CONFIG_CMD_MII
CONFIG_CMD_MTDPARTS
CONFIG_CMD_NAND
CONFIG_CMD_NAND_TRIMFFS
CONFIG_CMD_NFS
CONFIG_CMD_PCA953X
CONFIG_CMD_PCA953X_INFO
CONFIG_CMD_PCI
CONFIG_CMD_PING
CONFIG_CMD_READ
CONFIG_CMD_SF
CONFIG_CMD_SPI
CONFIG_CMD_SPL
CONFIG_CMD_SPL_WRITE_SIZE
CONFIG_CMD_TIME
CONFIG_CMD_TRACE
CONFIG_CMD_UBI
CONFIG_CMD_UBIFS
CONFIG_CMD_UNZIP
CONFIG_FS_EXT4

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: ti: dra7: move BOOTP_DNS2 and PHY_TI in defconfig

Move BOOTP_DNS2 and PHY_TI from dra7xx_evm.h to
dra7xx_evm_defconfig.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND

Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>

env: Finish migration of common ENV options

- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENT

Move this symbol to Kconfig. As part of this we can drop a UBI-specific
symbol that was a stop-gap for not having this particular symbol in
Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_SPI_U_BOOT_OFFS

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>

env: ti: boot: Use ttyS2 instead of ttyO2

ttyO2 console enables legacy CONFIG_SERIAL_OMAP driver in kernel.
Nowadays it's preferred to use the generic CONFIG_SERIAL_8250_OMAP
driver, which being enabled via ttyS2 console. Both drivers are enabled
in multi_v7_defconfig and in omap2plus_defconfig, for compatibility
reasons. Let's switch to ttyS2 console, to be sure that standard 8250
serial driver is used.

Similar behavior can be also achieved by enabling
CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP option in kernel, but it's better not
to rely on that, as it can be disabled or removed after transitional
period.

Right now on DRA7/AM57x platforms the 8250-omap driver is being probed
first, and omap-serial driver is only probed if the first one failed.
It can be seen from uart3 definition in arch/arm/boot/dts/dra7-l4.dtsi:

compatible = "ti,dra742-uart", "ti,omap4-uart";

So the kernel already uses 8250 driver. This change basically allows
kernel developers to throw away the omap-serial driver and associated
compatibility options. Similar discussions [1,2] have started several
years ago, so it should be safe to do that now.

[1] https://patchwork.kernel.org/patch/6198471/
[2] http://processors.wiki.ti.com/index.php/Sitara_Linux_UART_-_Switching_to_8250_Driver

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
[trini: Update omap5_uevm]
Signed-off-by: Tom Rini <trini@konsulko.com>

at91, omap2plus: configs: migrate CONFIG_ENV_ to defconfigs

Enable the extended ENV options for AT91 and OMAP2PLUS in order to be
able to use CONFIG_ENV_UBI_* on these architectures.

As this change also makes the configs ENV_SIZE, ENV_SECT_SIZE,
ENV_OFFSET visible to AT91 and OMAP2PLUS, migrate users of these to
KConfig.

This migration was run using an extended moveconfig.py which evaluates
expressions such as "(512 << 10)". See patch ("moveconfig: expand
simple expressions").

All modified boards were built with SOURCE_DATE_EPOCH=0 before and
after the change and successfully confirmed that the identical binary
is generated (the only exception was igep00x0, which does not define
CONFIG_ENV_IS_IN_UBI in the original board header. Once that is
defined, the test passes too).

hs: rebased patch to:
68b90e57bc: "configs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORT"

Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Tom Rini <trini@konsulko.com>

Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig

This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_BOOT

As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:

xilinx_zynqmp_zc1275_revB
xilinx_zynqmp_zc1751_xm018_dc4
xilinx_zynqmp_zc1751_xm019_dc5
xilinx_zynqmp_zcu100_revC
xilinx_zynqmp_zcu102_rev1_0
xilinx_zynqmp_zcu102_revA
xilinx_zynqmp_zcu102_revB
xilinx_zynqmp_zcu104_revA
xilinx_zynqmp_zcu104_revC
xilinx_zynqmp_zcu106_revA
xilinx_zynqmp_zcu111_revA

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>

spi: ti_qspi: Drop non DM code

Now that all boards using TI QSPI have moved to DM and DT, drop non DM
code completely.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[jagan: update MIGRATION.txt, rebase config_whitelist.txt]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: ti_omap5_common: Add NAND environment settings

Now that NAND is supported on DRA71x include various NAND environment
settings

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ENV_SPI_* to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE

Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

Convert CONFIG_SF_DEFAULT_* to Kconfig

This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

spl: Kconfig: Drop the _SUPPORT postfix from SPL_DFU

The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>

ata: Drop CONFIG_SYS_SCSI_MAX_* from boards using DM_SCSI

These options are not used or necessary when device model is being used
for SCSI. Just drop them.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_MII et al to Kconfig

This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: ti: boot: Extract PARTS_DEFAULT to boot.h

Eliminate code duplication: the same PARTS_DEFAULT was defined in
am57xx_evm.h and in dra7xx_evm.h. Extract it to environment/boot.h and
use in all OMAP5-based boards.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

spl: spi: Move CONFIG_SPL_SPI_LOAD to Kconfig

Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>

Migrate CONFIG_DRIVER_TI_CPSW to Kconfig

This converts CONFIG_DRIVER_TI_CPSW to Kconfig

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: OMAP5/DRA7: Enable iodelay recalibration to be done from uboot

Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.

The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

Convert CONFIG_OMAP_USB_PHY to Kconfig

This converts the following to Kconfig:
CONFIG_OMAP_USB_PHY

Signed-off-by: Adam Ford <aford173@gmail.com>

ata: Migrate CONFIG_LIBATA to Kconfig

This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

ata: Migrate CONFIG_SCSI_AHCI to Kconfig

And use 'imply' liberally.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

dra7x: fastboot: Increase recovery partition size

As per current android recommendation
https://source.android.com/devices/architecture/kernel/modular-kernels

1. Android recovery mode should contain both SOC and ODM
kernel modules in the recovery partition.

2. If a kernel module is required both in recovery and normal boot
mode, the module has to be located in recovery and vendor
partition seperately.

3. Kernel modules used in recovery mode should be independent
of vendor and odm partition

4. Recovery image should contain atleast
storage, display, keypad, battery and pmic modules.

Due to these requirements, recovery image size has increased
to >10MB.

This patch is to increase recovery partition size for TI devices
so that we dont see such flashing error

log:
sending 'recovery' (12560 KB)...
OKAY [ 0.436s]
writing 'recovery'...
FAILED (remote: too large for partition)
finished. total time: 0.458s

Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>

Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT

We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.

Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_NAND_OMAP_GPMC et al and CONFIG_NAND_MXC to Kconfig

This converts the following to Kconfig:
CONFIG_NAND_MXC
CONFIG_NAND_OMAP_GPMC
CONFIG_NAND_OMAP_GPMC_PREFETCH
CONFIG_NAND_OMAP_ELM
CONFIG_SPL_NAND_AM33XX_BCH
CONFIG_SPL_NAND_SIMPLE
CONFIG_SYS_NAND_BUSWIDTH_16BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>

arm: dra7xx: Add vendor partition to Android GPT table for eMMC

Add vendor partition to Android GPT table for eMMC.

A Vendor image contains SoC-specific code and configuration.

Prior to Android 8.0, the vendor partition was optional ;
files belonging to these images were placed in boot.img or system.img
with symlinks (such as /vendor >/system/vendor ) when absent.

Android 8.0 makes the vendor partition mandatory

The goal is to modularize Android partitions with standard interface between
the Android Platform (on system.img ) and vendor-provided code(on vendor.img).

This standard interface enables the Android Platform to be updated
without affecting the SoC partitions. This makes it possible to upgrade a
device system.img from Android 8.0 to Android P while other images (such as
vendor.img) remain at Android 8.0. This modularity enables timely
Android platform upgrades (such as monthly security updates )
without requiring SoC/ODM partners to update SoC- and device-specific code.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

cmd: Move CONFIG_RANDOM_UUID to Kconfig

CONFIG_RANDOM_UUID is used by the GPT command to generate random UUID when
none are provided.

Move that option to Kconfig.

Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

arm: dra7xx: Fix Linux boot from eMMC

Right now on OMAP5-based boards we have only one partition defined for
Linux boot, which is rootfs. That doesn't work with bootpart=1:2 (that
is defined in include/environment/ti/boot.h). To fix Linux boot we may
either:

1. Change bootpart to be 1:1
2. Or add preceding partition, so that rootfs is actually 1:2

Second choice seems more reasonable, as DFU is already using similar
partition table and can rely on bootpart to be 1:2.

This patch adds "bootloader" partition. So now eMMC layout for Linux
boot looks like this:

offset content size partition
(KiB) (KiB)
Reviewed-by: Tom Rini <trini@konsulko.com>

=======================================================================

0 +--------------------------------+
| MBR/GPT header | 128 -
128 +--------------------------------+
| MLO | 256 -
384 +--------------------------------+
| u-boot.img | 1792 bootloader
2176 +--------------------------------+
| //////////// hole //////////// | 256 -
2432 +--------------------------------+
| U-Boot environment | 128 -
2560 +--------------------------------+
| U-Boot environment (redundant) | 128 -
2688 +--------------------------------+
| rootfs | remaining rootfs
end +--------------------------------+

=======================================================================

Guard hole appears because U-Boot environment offset was calculated for
Android partition table, which has two additional partitions in place of
that hole ("environment" and "misc" partitions).

This patch also changes rootfs offset from 2 MiB further to 2688 KiB,
so that there won't be any collisions with U-Boot environment when we
flash rootfs.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

Kconfig: Migrate all of cmd/fastboot/Kconfig to defconfigs

- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's
not strictly part of fastboot.
- Add some defaults for the fastboot buffer location and size
- Migrate all options listed in cmd/fastboot/Kconfig
- Cleanup the README

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_OMAP3_SPI to Kconfig

This converts the following to Kconfig:
CONFIG_OMAP3_SPI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Minor comment tweaks]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CMD_SPL_WRITE_SIZE to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SPL_WRITE_SIZE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Convert CONFIG_CMD_SPL_NAND_OFS to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SPL_NAND_OFS

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

configs: Finish migration of PHY_GIGE

Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Move PHYLIB to Kconfig

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs: Remove CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS in all boards

Now that xHCD does not use CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>

Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_ENV_IS_IN_FLASH to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SCSI to Kconfig

This converts the following to Kconfig:
CONFIG_SCSI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

arm: dra7: Increase "bootloader" partition size

Increase the size of u-boot.img, so that it conforms with new DFU
configuration (see commit [1]).

[1] 7a53a1a8115b ARM: ti: Update layout for MMC and eMMC (env and dfu)

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

ARM: ti: Update layout for MMC and eMMC (env and dfu)

The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area (2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region
"spl-os-image.raw".
both: region "spl-os-image.raw" is quite small and can't handle android
kernels

Fixing this requires growing some regions and moving others.
Care has been taken to leave some room for further growth of
"spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the
region is not free space that can be used to grow "u-boot.img.raw".
The MLO region is 0x100 sectors wide but the 0x100 are unused in case the
MLO comes too overflow this areas.
The total space allocated for those raw binaries is 16MB, of which 13+MB
are reserved for the kernel image.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>

Convert CONFIG_CMD_EEPROM et al to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRING

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>

arm: dra7xx: move CONFIG_DRA7XX to Kconfig

The symbol CONFIG_DRA7XX is needed for Kconfig conditions.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>

configs: dra7xx_evm: Enable SPL_DM

Enable SPL_DM on all DRA7 based platforms.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: Use Kconfig for board EEPROM's I2C bus and chip address

In stead of defining the board EEPROM address in the board headers
let's define them in the board config files and make them
configurable by Kconfig.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Kconfig: Migrate CONFIG_BAUDRATE

Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

flash: complete CONFIG_SYS_NO_FLASH move with renaming

We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

cmd, disk: convert CONFIG_PARTITION_UUIDS, CMD_PART and CMD_GPT

We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_EFI_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig

This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>

config: Move CONFIG_BOARD_LATE_INIT to defconfigs

Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>

ARM: ti: consolidate dfu environment variables

Introduce include/environment/ti/dfu.h that
consolidates environment variable definitions
for various TI boards that support DFU today.

Tested on AM335x EVM, AM437x SK EVM and DRA74x
EVM by using DFU to write to SD card.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

spl: dfu: move DFU Kconfig to SPL Kconfig

The DFU Kconfig menu entries should be part of the SPL
Kconfig file. Also avoid using the top level Makefile by
moving the config dependent build artifacts to the driver/
and driver/usb/gadget/ Makfiles.

With that, DFU can be built again in SPL if
CONFIG_SPL_DFU_SUPPORT is enabled.

Fixes: 6ad6102246d8 ("usb:gadget: Disallow DFU in SPL for now")

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>

arm: dra7xx: Unify Android partition table

Make Android partition table the same as for AM57x EVM.

1. Make "bootloader" partition start from 0x300 sectors offset, so
DRA7 is bootable in Android mode (see
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR option).
2. Increase "bootloader" partition size, because size of u-boot.img is
about 632 KiB (when building DT defconfig, with FIT image enabled).
3. Specify "reserved" partition explicitly, rather than specifying
"efs" partition start. Reserved area will be used to store U-Boot
environment on eMMC. It's convenient to have it exposed explicitly
so we can read/write U-Boot environment.
4. Keep all Android partitions locations intact, by reducing
"reserved" partition size. CONFIG_ENV_SIZE is considered.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

dra7x: dfu: qspi: increase the qspi spl partition to 256K

The SPL size for dra7x platform increased beyond 64K,
increasing the size to 256K to cater for future enhancement.

Signed-off-by: Ravi Babu <ravibabu@ti.com>

dra7xx: config: cleanup: moved to kconfig for CONFIG_SPL_ENV_SUPPORT

removing CONFIG_SPL_ENV_SUPPORT defined in header files
due to moved to kconfig option for CONFIG_SPL_ENV_SUPPORT

Signed-off-by: Ravi Babu <ravibabu@ti.com>

arm: dra7xx: Move fastboot options to defconfig

Now that fastboot options are available in Kconfig, we can migrate them
from DRA7 header to corresponding DRA7 defconfigs.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

Merge branch 'master' of git://git.denx.de/u-boot-usb

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
include/configs/dra7xx_evm.h

dra7x: configs: enable SPL-DFU support

This patch enables the SPL-DFU support for
dra7x platform.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

dfu: Migrate to Kconfig

Introduce a hidden USB_FUNCTION_DFU Kconfig option and select it for
CMD_DFU (as we must have the DFU command enabled to do anything DFU).
Make all of the entries in drivers/dfu/Kconfig depend on CMD_DFU and add
options for all of the back end choices that DFU can make use of.

Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>

Convert CONFIG_SPL_SPI_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_SPI_FLASH_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_MMC_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_ENV_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_DMA_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Migrate CONFIG_USB_STORAGE

In some cases we were missing CONFIG_USB=y so enable that when needed.

Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

TI: Rework SRAM definitions and maximums

On all TI platforms the ROM defines a "downloaded image" area at or near
the start of SRAM which is followed by a reserved area. As it is at
best bad form and at worst possibly harmful in corner cases to write in
this reserved area, we stop doing that by adding in the define
NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image
area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this.
At current we define the end of scratch space at 0x228 bytes past the
start of scratch space this this gives us a lot of room to grow. As
these scratch uses are non-optional today, all targets are modified to
respect this boundary.

Tested on OMAP4 Pandaboard, OMAP3 Beagle xM

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Weber <weber@corscience.de>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: "B, Ravi" <ravibabu@ti.com>
Cc: "Matwey V. Kornilov" <matwey.kornilov@gmail.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: "Kipisz, Steven" <s-kipisz2@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>

usb: add (move) CONFIG_USB_HOST to Kconfig

The meaning of CONFIG_USB in U-Boot is different from that in Linux.

As you see in drivers/usb/Kconfig of Linux, CONFIG_USB enables the
USB host controller support, while CONFIG_USB_SUPPORT is used to
enable the whole of the USB sub-system.

When I added CONFIG_USB into Kconfig by commit 6e7e9294d321 ("usb:
add basic USB configs in Kconfig"), I planned to follow the Linux's
convention, i.e. CONFIG_USB to enable/disable the USB host support.

Then, commit 68f7c5db2d1e ("usb: Generic USB Kconfig option, that
fits both host and gadget and comments") changed the logic of the
CONFIG_USB to point to the whole of the USB sub-system. As a result,
currently we do not have an option for USB host.

This commit adds CONFIG_USB_HOST, which will be useful to compile
in the USB host support code.

CONFIG_USB_HOST is not referenced at all, but strangely some boards
define it in board headers. I removed them because USB_HOST will be
selected in Kconfig going forward.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

treewide: move CONFIG_PHYS_64BIT to Kconfig

We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system. Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.

Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6d4 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.

I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable. However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.

CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.

Fixes: 95ebc253e6d4 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>

configs: dra7xx: Update QSPI speed to 76.8MHz

Now that QSPI driver can support 76.8MHz, update the
CONFIG_SF_DEFAULT_SPEED to the same value.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>

usb: move CONFIG_USB_XHCI_DWC3 to Kconfig

Create an entry for "config USB_XHCI_DWC3" in Kconfig and
switch over to it for all boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

usb: move CONFIG_USB_XHCI to Kconfig with renaming

Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it
into CONFIG_USB_XHCI_HCD.

As commented in the help of "config USB_XHCI" entry, this has been
a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI
have been unified in favor of the former.

Note:
Some boards define CONFIG_USB_XHCI in their headers without
CONFIG_USB, which does not meet the "depends on" in Kconfig.
I added CONFIG_USB=y for those boards when converting.
Otherwise, they would fail to build.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

dm: scsi: Rename CONFIG_CMD_SCSI to CONFIG_SCSI

This option currently enables both the command and the SCSI functionality.
Rename the existing option to CONFIG_SCSI since most of the code relates
to the feature.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

usb: gadget Move: CONFIG_G_DNL_* to Kconfig

And also reformat defconfigs using "make savedefconfig" rule.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

usb: dwc3: Move CONFIG_USB_DWC3_PHY_* to Kconfig

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

usb: dwc3: Move CONFIG_USB_DWC3_OMAP to Kconfig

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

usb: dwc3: Move CONFIG_USB_DWC3_GADGET/HOST to Kconfig

Description was borrowed from kernel dwc3 Kconfig.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

usb: gadget: Move CONFIG_USB_GADGET_DOWNLOAD to Kconfig

While at it, remove obsolete CONFIG_USBDOWNLOAD_GADGET option from some
config headers. This is also probably fixes am335x_baltos board.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

usb: gadget: Move CONFIG_USB_GADGET_DUALSPEED to Kconfig

Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and
make all UDC controllers select USB_GADGET_DUALSPEED:
- add next options to Kconfig selecting USB_GADGET_DUALSPEED:
- USB_GADGET_ATMEL_USBA
- USB_GADGET_DWC2_OTG
- USB_DWC3
- CI_UDC
- make USB_MUSB_GADGET select USB_GADGET_DUALSPEED

While at it, make some related fixes:
- remove DUALSPEED from configs that don't enable gadget support:
- kwb.h
- tseries.h
- add missing USB_GADGET option to next configs:
- novena_defconfig
- pcm051_rev*_defconfig
- xfi3_defconfig

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

usb: gadget: Move CONFIG_USB_GADGET_VBUS_DRAW to Kconfig

The description was borrowed from kernel. Definitions were added to
defconfig files in a way that "make savedefconfig" generates exactly
the same file as used defconfig.

Boards using 0 mA as CONFIG_USB_GADGET_VBUS_DRAW value were moved to use
2 mA (as minimal allowed by Kconfig).

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

board: ti: DRA7: Add DP83867 TI phy for rev c

Enable the TI DP83867 Giga bit phy on the
dra7 rev c board. The rx and tx internal
delays are need for this board so the usage
of RGMII_ID is required.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

usb: gadget: Move CONFIG_USB_GADGET to Kconfig

The description was borrowed from kernel. "tristate" type was changed
to "bool" (I believe we don't support modules for u-boot yet, right?).
CONFIG_USB_GADGET requires CONFIG_USB to be defined too, so add it along
as well.

Definitions were added to defconfig files in a way that
"make savedefconfig" generates exactly the same file as used defconfig.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Add zynq_zc702 conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: DRA7: configs: Prepare for detecting memory > 2GB

Enable configs that are required for detecting memory > 2GB.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: DRA7: Enable EEPROM support

Enable EEPROM support for DRA74-evm.

Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: dra7xx: Define Android partition table

"fastboot oem format" command reuses "gpt write" command, which in turn
requires correct partitions defined in $partitions variable. This patch
adds such definition of Android partitions for DRA7XX EVM board.

By default $partitions variable contains Linux partition table. In order
to prepare Android environment one can run next commands from U-Boot
shell:

=> env set partitions $partitions_android
=> env save

After those operations one can go to fastboot mode and perform
"fastboot oem format" to create Android partition table.

While at it, enable CONFIG_RANDOM_UUID to spare user from providing
UUIDs for each partition manually.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

ARM : DRA7: Switch QSPI to use MODE-0 at 64MHz

According to Data Manual(SPRS915P) of AM572x, TI QSPI controller on
DRA74 EVM(rev 1.1+) can support up to 64MHz in MODE-0, whereas MODE-3 is
limited to 48MHz. Hence, switch to MODE-0 for better throughput.
Also, add IODelay parameters for the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

dra7xx_evm: qspi: do not define DM_SPI and DM_SPI_FLASH for spl

Since OMAP's spl doesn't support DM currently, do not define DM_SPI and
DM_SPI_FLASH for spl build.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

sf: Move SPI flash drivers to defconfig

There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>

spi: Move SPI drivers to defconfig

There are already Kconfig options for SPI drivers, but we
have not moved them from config.h to defconfig files. This
commit does this in a batch.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>

ARM: dra7xx_evm: Add DFU support for qspi flash

This adds support to update firmware on qspi flash using DFU.

On device:
=> setenv dfu_alt_info ${dfu_alt_info_qspi}
=> dfu 0 sf 0:0

On host:
$ sudo dfu-util -l
$ sudo dfu-util -D MLO -a MLO
$ sudo dfu-util -D u-boot.img -a u-boot.img

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

ARM: dra7xx_evm: Enable EDMA3 in SPL to support DMA on qspi

Enable TI_EDMA3 and SPL_DMA support, so as to reduce boot time. With
DMA enabled there is almost 3x improvement in read performance. This
helps in reducing boot time in qspiboot mode

Also add EDMA3 base address for DRA7XX and AM57XX.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

usb: CONFIG_USB_FASTBOOT prefix replacement for consistency

FASTBOOT is defined both by CONFIG_USB_FUNCTION_FASTBOOT AND CONFIG_CMD_FASTBOOT, so it doesn't
make much sense to have a CONFIG_USB_FASTBOOT prefix for fastboot-specific options, especially
given that other config options for fastboot use the CONFIG_FASTBOOT prefix.

This replaces the CONFIG_USB_FASTBOOT prefix with CONFIG_FASTBOOT, for consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>

usb: Fastboot function config for better consistency with other functions

USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>

Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)

usb: USB download gadget and functions config options coherent naming

This introduces a coherent scheme for naming USB download gadget and functions
config options. The download USB gadget config option is moved to
CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each
function's config option is moved to a CONFIG_USB_FUNCTION_ prefix.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>

Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)

usb: xhci: omap: Remove common dwc3 drv functions calls

Remove all redundant dwc3 driver function calls that
are defined by dwc3 driver

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>

defconfig: Move CONFIG_SPI_FLASH_BAR from configs

This commit moves:
- CONFIG_SPI_FLASH_BAR

from include/configs/*.h into configs/*_defconfigs

Signed-off-by: Jagan Teki <jteki@openedev.com>

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

Move default y configs out of arch/board Kconfig

Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.

Remove the configs that behave this way from the archs.

A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:

SPIFLASH
DISPLAY_BOARDINFO

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>

omap5: Exclude more environment from SPL builds

In the cases where we make use of environment in SPL we do not need
these defaults compiled in and available. These are taking up space
that in some cases now prevent linking, so drop.

Signed-off-by: Tom Rini <trini@konsulko.com>

am335x_evm: am44xx_evm: dra7xx_evm: nand: Fix file-system partition name

We almost always use UBIFS for user accessible NAND file systems and
the UBIFS file system might contain more than one volume within the
single NAND partition. The last NAND partition is therefore more
appropriately named as "NAND.file-system" instead of "NAND.rootfs"

The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the
last NAND partition. This patch makes the partition name consistent
between u-boot and the kernel.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

ARM: DRA7-evm: Enable IO delay recalibration sequence

Enabling IO delay recalibration sequence for DRA7 EVM.
UART and I2C are configured before IO delay recalibration sequence
as these are used earlier and safe to use.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>

net: Move the CMD_NET config to defconfigs

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

ARM: DRA7XX: Enable Fastboot

- Fastboot is enable by default for DRA7XX
- This is based on following patch modified accordingly
http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=b2e04f92b5d91c708b6fd6b79d2266966ac51f4b

Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

include: configs: Enable DWC3 and DFU in DRA7xx

Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>

qspi: dra7x: enable quad mode read for ti-qspi driver

This patch enables QUAD read mode for qspi to improve the
read performace while loading the binaries from qspi.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

TI: armv7: enable UUID and PART

Enable UUID and partition support for scripted handling platforms with
MMC and eMMC and varied partitioning schemes

And remove it from headers that end up redefining it.

Signed-off-by: Nishanth Menon <nm@ti.com>

ARM: OMAP5: DRA7xx: Enable 8-bit eMMC access on the dra7xx_evm

Tested on a Vayu EVM Rev.E2 with DRA752 ES1.1

Signed-off-by: Lubomir Popov <l-popov@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>

spl: replace CONFIG_SPL_SPI_* with CONFIG_SF_DEFAULT_*

Currently, CONFIG_SPL_SPI_* #defines are used for controlling SPI boot in
SPL. These #defines do not allow the user to select SPI mode for the SPI flash
(there's no CONFIG_SPL_SPI_MODE, so the SPI mode is hardcoded in
spi_spl_load.c), and duplicate information already provided by
CONFIG_SF_DEFAULT_* #defines.

Kill CONFIG_SPL_SPI_*, and use CONFIG_SF_DEFAULT_* instead.

Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Hannes Petermaier <hannes.petermaier@br-automation.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>

ARM: DRA: Enable VTT regulator

DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

board/ti/dra7xx: add support for parallel NOR

This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.

As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
SW5.1 (NAND_BOOTn) = OFF (logic-1)
SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)

And also set appropriate SYSBOOT configurations:
SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */

Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:

board/ti/dra7xx: add support for parallel NAND

This patch adds support for x16 NAND device (MT29F2G16AAD) connected to GPMC
chip-select[0] on DRA7xx EVM.
As GPMC pins are shared by multiple devices, so in addition to this patch
following board settings are required for NAND device detection [1]:

SW5.9 (GPMC_WPN) = OFF (logic-1)
SW5.1 (NAND_BOOTn) = ON (logic-0) /* Active-low */
SW5.2 (NOR_BOOTn) = OFF (logic-1)
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)

And also set appropriate SYSBOOT configurations
SW2.1 (SYSBOOT[0]) = ON (logic-1) /* selects NAND Boot */
SW2.2 (SYSBOOT[1]) = OFF (logic-0) /* selects NAND Boot */
SW2.3 (SYSBOOT[2]) = OFF (logic-0) /* selects NAND Boot */
SW2.4 (SYSBOOT[3]) = OFF (logic-0) /* selects NAND Boot */
SW2.5 (SYSBOOT[4]) = ON (logic-1) /* selects NAND Boot */
SW2.6 (SYSBOOT[5]) = ON (logic-1) /* selects NAND Boot */
SW2.7 (SYSBOOT[6]) = OFF (logic-0) /* reserved */
SW2.8 (SYSBOOT[7]) = OFF (logic-0) /* reserved */

SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Addr/Data Muxed */
SW3.5 (SYSBOOT[12])= ON (logic-1) /* device type: Addr/Data Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */

Following changes are required in board.cfg to enable NAND on J6-EVM:

dra7xx_evm: Add QSPI_4 support, qspiboot build target

We previously only supported QSPI_1 (single) support. Add QSPI_4 (quad)
read support as well. This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value. We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment. When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>

TI:omap5: Move CONFIG_ENV_SIZE to board config files

The size of the environment depends on the backing store, move this to
the board config files.

Signed-off-by: Tom Rini <trini@ti.com>

drivers: net: cpsw: add support to have phy address from cpsw platform data

Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>

dra7xx_evm: Enable GPT commands

Signed-off-by: Tom Rini <trini@ti.com>

Merge branch 'master' of git://git.denx.de/u-boot-arm

dra7xx_evm: Add CONFIG_SUPPORT_EMMC_BOOT, document usage

Add a README to the board which lists the commands required to enable
booting from the eMMC boot partitions found on the board.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>

ARM: OMAP5: Rename to ti_omap5_common.h

Follow the pattern ti_<processor family>_common.h used by other TI processors
to be coherent. So just rename omap5_common.h to ti_omap5_common.h.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

config: dra7_evm: Add Bank Address Register(BAR) config

Add config to support bank address register.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Yebio Mesfin <ymesfin@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>

ARM: dra7_evm: Add SATA support

The evm has a SATA port. Enable SATA configuration and
inititialize the SATA controller.

Signed-off-by: Roger Quadros <rogerq@ti.com>

Merge branch 'iu-boot/master' into 'u-boot-arm/master'

Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

board/compulab/common/Makefile
board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h

dra7xx_evm: Enabled UART-boot mode and add dra7xx_evm_uart3 build

UART booting is supported on this SoC, but via UART3 rather than UART1.
Because of this we must change the board to use UART3 for all console
access (only one UART is exposed on this board and a slight HW mod is
required to switch UARTs).

Signed-off-by: Minal Shah <minal.shah@ti.com>
[trini: Make apply to mainline, reword commit]
Signed-off-by: Tom Rini <trini@ti.com>

usb: dra7xx: Add support for dra7xx xhci USB host

Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.

The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>

Coding Style cleanup: remove trailing white space

Signed-off-by: Wolfgang Denk <wd@denx.de>

dra7xx_evm: add SPL API, QSPI, and serial flash support

Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.

Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

ARM: DRA7: Enable saveenv command

dra7xx_evm has eMMC and the default environment can be stored in it.
So enabling saveenv command and the configs to store environment in eMMC.

Tested on DRA752 ES1.0

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

dra7xx_evm: Re-order and comment the networking related config options

Signed-off-by: Tom Rini <trini@ti.com>

TI:omap5/dra7xx: Convert to ti_armv7_common.h

Update omap5_common.h to use ti_armv7_common.h, and in turn update
dra7xx_evm.h and omap5_uevm.h slightly. The biggest changes here are
that IP blocks which exist on the platform, and had clocks enabled,
now have the drivers being built as well.

Signed-off-by: Tom Rini <trini@ti.com>

ARM: DRA7xx: Enable CPSW Ethernet support

Enabling CPSW Ethernet support in DRA7xx EVM.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>

Add GPL-2.0+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>

arm: dra7xx: Update the EXTRA_ENV_SETTINGS

Update the EXTRA_ENV_SETTING for the dra7xx.
The console needs to be set to ttyO0 and the
findfdt needs to be updated to load the
dra7xx-evm.dtb file.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>

ARM: DRA7xx: clocks: Update PLL values

Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>

ARM: DRA7xx: Change the Debug UART to UART1

Serial UART is connected to UART1. So add the change
for the same.

Signed-off-by: Sricharan R <r.sricharan@ti.com>

ARM: DRA7xx: Add control id code for DRA7xx

The registers that are used for device identification
are changed from OMAP5 to DRA7xx.
Using the correct registers for DRA7xx.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

omap5_uevm.h: Move uEVM-specific choices to omap5_uevm.h

The omap5_uevm platform has eMMC, and it makes sense to say that our
default env storage shall reside there. Other platforms may not, so
move this choice to the EVM config. In addition, we should provide some
way to partition the flash for later usage, so take advantage of the GPT
partition table support code and allow that to be setup with some
reasonable defaults.

Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>

arm: dra7xx: Add dra7xx_evm build support

Adding the build support for dra7xx_evm.
Reusing omap5_evm.h config by moving it to omap5_common.h

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>

global: Migrate CONFIG_MAX_MEM_MAPPED to CFG

Perform a simple rename of CONFIG_MAX_MEM_MAPPED to CFG_MAX_MEM_MAPPED

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Remove unused CONFIG symbols

This removes the following unreferenced CONFIG symbols:
CONFIG_FDTADDR
CONFIG_FDTFILE
CONFIG_FLASH_SECTOR_SIZE
CONFIG_FSL_CPLD
CONFIG_HDMI_ENCODER_I2C_ADDR
CONFIG_I2C_MVTWSI
CONFIG_I2C_RTC_ADDR
CONFIG_IRAM_END
CONFIG_IRAM_SIZE
CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
CONFIG_L1_INIT_RAM
CONFIG_MACB_SEARCH_PHY
CONFIG_MIU_2BIT_21_7_INTERLEAVED
CONFIG_MTD_NAND_VERIFY_WRITE
CONFIG_MVGBE_PORTS
CONFIG_NETDEV
CONFIG_NUM_DSP_CPUS
CONFIG_PHY_BASE_ADR
CONFIG_PHY_INTERFACE_MODE
CONFIG_PSRAM_SCFG
CONFIG_RAMBOOT_SPIFLASH
CONFIG_RAMBOOT_TEXT_BASE
CONFIG_RD_LVL
CONFIG_ROCKCHIP_SDHCI_MAX_FREQ
CONFIG_SETUP_INITRD_TAG
CONFIG_SH_QSPI_BASE
CONFIG_SMDK5420
CONFIG_SOCRATES
CONFIG_SPI_ADDR
CONFIG_SPI_FLASH_QUAD
CONFIG_SPI_FLASH_SIZE
CONFIG_SPI_HALF_DUPLEX
CONFIG_SPI_N25Q256A_RESET
CONFIG_TEGRA_SLINK_CTRLS
CONFIG_TPM_TIS_BASE_ADDRESS
CONFIG_UBOOT_SECTOR_COUNT
CONFIG_UBOOT_SECTOR_START
CONFIG_VAR_SIZE_SPL
CONFIG_VERY_BIG_RAM

And also:
BL1_SIZE
PHY_NO
RESERVE_BLOCK_SIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_HSMMC2_8BIT to Kconfig

This converts the following to Kconfig:
CONFIG_HSMMC2_8BIT

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_IODELAY_RECALIBRATION to Kconfig

This converts the following to Kconfig:
CONFIG_IODELAY_RECALIBRATION

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Move remaining CONFIG_SYS_* to CFG_SYS_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_OMAP_ABE_SYSCK to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_OMAP_ABE_SYSCK

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_NS16550_* to CFG_SYS_NS16550_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_NAND_* to CFG_SYS_NAND_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_MAX_FLASH_SECT to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MAX_FLASH_SECT

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_SPL_KERNEL_OFFS to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_SPL_KERNEL_OFFS

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_FLASH_CFI_WIDTH to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_FLASH_CFI_WIDTH

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MONITOR_BASE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE

Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_NET_RETRY_COUNT to Kconfig

This converts the following to Kconfig:
CONFIG_NET_RETRY_COUNT

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SCSI_AHCI_PLAT et al to Kconfig

This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE

Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>

configs: Migrate CONFIG_SYS_MAX_FLASH_BANKS to Kconfig

Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

scripts: remove some configs in config_whitelist.txt

Remove some config finishing by _ badly added by
scripts/build-whitelist.sh when joker is used in comments.

for example:
doc/uImage.FIT/command_syntax_extensions.txt:
... #ifdef CONFIG_OF_* | ...

cmd/nvedit.c:# error Define one of CONFIG_ENV_IS_IN_{EEPROM| \
FLASH|MMC|FAT|EXT4|\

Remove also configs only used in comments:
- CONFIG_BOOGER in include/linux/kconfig.h
- CONFIG_COMMANDS
- CONFIG_INIT_IGNORE_ERROR
- CONFIG_REG_*
- CONFIG_HOTPLUG : drivers/watchdog/omap_wdt.c:18

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_NAND_OMAP_ECCSCHEME to Kconfig

The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_U_BOOT_LOCATIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_U_BOOT_LOCATIONS
CONFIG_SYS_NAND_U_BOOT_OFFS

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_ONFI_DETECTION to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_ONFI_DETECTION

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_5_ADDR_CYCLE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_5_ADDR_CYCLE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_BAD_BLOCK_POS to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS

In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_NAND_PAGE_COUNT to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_NAND_PAGE_COUNT

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SPL_NAND_LOAD et al to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_USB_XHCI_OMAP to Kconfig

This converts the following to Kconfig:
CONFIG_USB_XHCI_OMAP

Signed-off-by: Tom Rini <trini@konsulko.com>

usb: phy: ti: Remove non-DM PHY code

At this point in time, all platforms that had previously used
drivers/usb/phy/omap_usb_phy.c have been migrated to DM and related
options. Remove this now unused code and some related unused defines.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to Kconfig

- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

eeprom: Drop CONFIG_ENV_EEPROM_IS_ON_I2C usage

At this point in time, there's no systems with "U-Boot environment
exists on an EEPROM which is accessed over the I2C bus" that sets this
option. Drop it.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MMC_ENV_DEV et al to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART

Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: migrate CONFIG_SPL_LOAD_FIT_ADDRESS to defconfigs

Done with:
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS -H

Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: A few more migrations]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_SEND_HOSTNAME to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_SEND_HOSTNAME

Signed-off-by: Adam Ford <aford173@gmail.com>

Convert CONFIG_CMD_ASKENV et al to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_ASKENV
CONFIG_CMD_BMP
CONFIG_CMD_BOOTD
CONFIG_CMD_CACHE
CONFIG_CMD_CRC32
CONFIG_CMD_DHCP
CONFIG_CMD_ENV
CONFIG_CMD_EXPORTENV
CONFIG_CMD_EXT2
CONFIG_CMD_EXT4
CONFIG_CMD_FLASH
CONFIG_CMD_FS_GENERIC
CONFIG_CMD_FUSE
CONFIG_CMD_GPIO
CONFIG_CMD_GPT
CONFIG_CMD_GREPENV
CONFIG_CMD_I2C
CONFIG_CMD_IMLS
CONFIG_CMD_IMPORTENV
CONFIG_CMD_LOADB
CONFIG_CMD_LOADS
CONFIG_CMD_MEMINFO
CONFIG_CMD_MII
CONFIG_CMD_MTDPARTS
CONFIG_CMD_NAND
CONFIG_CMD_NAND_TRIMFFS
CONFIG_CMD_NFS
CONFIG_CMD_PCA953X
CONFIG_CMD_PCA953X_INFO
CONFIG_CMD_PCI
CONFIG_CMD_PING
CONFIG_CMD_READ
CONFIG_CMD_SF
CONFIG_CMD_SPI
CONFIG_CMD_SPL
CONFIG_CMD_SPL_WRITE_SIZE
CONFIG_CMD_TIME
CONFIG_CMD_TRACE
CONFIG_CMD_UBI
CONFIG_CMD_UBIFS
CONFIG_CMD_UNZIP
CONFIG_FS_EXT4

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: ti: dra7: move BOOTP_DNS2 and PHY_TI in defconfig

Move BOOTP_DNS2 and PHY_TI from dra7xx_evm.h to
dra7xx_evm_defconfig.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND

Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>

env: Finish migration of common ENV options

- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENT

Move this symbol to Kconfig. As part of this we can drop a UBI-specific
symbol that was a stop-gap for not having this particular symbol in
Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_SPI_U_BOOT_OFFS

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>

env: ti: boot: Use ttyS2 instead of ttyO2

ttyO2 console enables legacy CONFIG_SERIAL_OMAP driver in kernel.
Nowadays it's preferred to use the generic CONFIG_SERIAL_8250_OMAP
driver, which being enabled via ttyS2 console. Both drivers are enabled
in multi_v7_defconfig and in omap2plus_defconfig, for compatibility
reasons. Let's switch to ttyS2 console, to be sure that standard 8250
serial driver is used.

Similar behavior can be also achieved by enabling
CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP option in kernel, but it's better not
to rely on that, as it can be disabled or removed after transitional
period.

Right now on DRA7/AM57x platforms the 8250-omap driver is being probed
first, and omap-serial driver is only probed if the first one failed.
It can be seen from uart3 definition in arch/arm/boot/dts/dra7-l4.dtsi:

compatible = "ti,dra742-uart", "ti,omap4-uart";

So the kernel already uses 8250 driver. This change basically allows
kernel developers to throw away the omap-serial driver and associated
compatibility options. Similar discussions [1,2] have started several
years ago, so it should be safe to do that now.

[1] https://patchwork.kernel.org/patch/6198471/
[2] http://processors.wiki.ti.com/index.php/Sitara_Linux_UART_-_Switching_to_8250_Driver

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
[trini: Update omap5_uevm]
Signed-off-by: Tom Rini <trini@konsulko.com>

at91, omap2plus: configs: migrate CONFIG_ENV_ to defconfigs

Enable the extended ENV options for AT91 and OMAP2PLUS in order to be
able to use CONFIG_ENV_UBI_* on these architectures.

As this change also makes the configs ENV_SIZE, ENV_SECT_SIZE,
ENV_OFFSET visible to AT91 and OMAP2PLUS, migrate users of these to
KConfig.

This migration was run using an extended moveconfig.py which evaluates
expressions such as "(512 << 10)". See patch ("moveconfig: expand
simple expressions").

All modified boards were built with SOURCE_DATE_EPOCH=0 before and
after the change and successfully confirmed that the identical binary
is generated (the only exception was igep00x0, which does not define
CONFIG_ENV_IS_IN_UBI in the original board header. Once that is
defined, the test passes too).

hs: rebased patch to:
68b90e57bc: "configs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORT"

Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Tom Rini <trini@konsulko.com>

Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig

This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_BOOT

As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:

xilinx_zynqmp_zc1275_revB
xilinx_zynqmp_zc1751_xm018_dc4
xilinx_zynqmp_zc1751_xm019_dc5
xilinx_zynqmp_zcu100_revC
xilinx_zynqmp_zcu102_rev1_0
xilinx_zynqmp_zcu102_revA
xilinx_zynqmp_zcu102_revB
xilinx_zynqmp_zcu104_revA
xilinx_zynqmp_zcu104_revC
xilinx_zynqmp_zcu106_revA
xilinx_zynqmp_zcu111_revA

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>

spi: ti_qspi: Drop non DM code

Now that all boards using TI QSPI have moved to DM and DT, drop non DM
code completely.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[jagan: update MIGRATION.txt, rebase config_whitelist.txt]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

configs: ti_omap5_common: Add NAND environment settings

Now that NAND is supported on DRA71x include various NAND environment
settings

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ENV_SPI_* to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE

Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

Convert CONFIG_SF_DEFAULT_* to Kconfig

This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

spl: Kconfig: Drop the _SUPPORT postfix from SPL_DFU

The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>

ata: Drop CONFIG_SYS_SCSI_MAX_* from boards using DM_SCSI

These options are not used or necessary when device model is being used
for SCSI. Just drop them.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_MII et al to Kconfig

This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: ti: boot: Extract PARTS_DEFAULT to boot.h

Eliminate code duplication: the same PARTS_DEFAULT was defined in
am57xx_evm.h and in dra7xx_evm.h. Extract it to environment/boot.h and
use in all OMAP5-based boards.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

spl: spi: Move CONFIG_SPL_SPI_LOAD to Kconfig

Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>

Migrate CONFIG_DRIVER_TI_CPSW to Kconfig

This converts CONFIG_DRIVER_TI_CPSW to Kconfig

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: OMAP5/DRA7: Enable iodelay recalibration to be done from uboot

Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.

The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

Convert CONFIG_OMAP_USB_PHY to Kconfig

This converts the following to Kconfig:
CONFIG_OMAP_USB_PHY

Signed-off-by: Adam Ford <aford173@gmail.com>

ata: Migrate CONFIG_LIBATA to Kconfig

This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

ata: Migrate CONFIG_SCSI_AHCI to Kconfig

And use 'imply' liberally.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

dra7x: fastboot: Increase recovery partition size

As per current android recommendation
https://source.android.com/devices/architecture/kernel/modular-kernels

1. Android recovery mode should contain both SOC and ODM
kernel modules in the recovery partition.

2. If a kernel module is required both in recovery and normal boot
mode, the module has to be located in recovery and vendor
partition seperately.

3. Kernel modules used in recovery mode should be independent
of vendor and odm partition

4. Recovery image should contain atleast
storage, display, keypad, battery and pmic modules.

Due to these requirements, recovery image size has increased
to >10MB.

This patch is to increase recovery partition size for TI devices
so that we dont see such flashing error

log:
sending 'recovery' (12560 KB)...
OKAY [ 0.436s]
writing 'recovery'...
FAILED (remote: too large for partition)
finished. total time: 0.458s

Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>

Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT

We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.

Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_NAND_OMAP_GPMC et al and CONFIG_NAND_MXC to Kconfig

This converts the following to Kconfig:
CONFIG_NAND_MXC
CONFIG_NAND_OMAP_GPMC
CONFIG_NAND_OMAP_GPMC_PREFETCH
CONFIG_NAND_OMAP_ELM
CONFIG_SPL_NAND_AM33XX_BCH
CONFIG_SPL_NAND_SIMPLE
CONFIG_SYS_NAND_BUSWIDTH_16BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>

arm: dra7xx: Add vendor partition to Android GPT table for eMMC

Add vendor partition to Android GPT table for eMMC.

A Vendor image contains SoC-specific code and configuration.

Prior to Android 8.0, the vendor partition was optional ;
files belonging to these images were placed in boot.img or system.img
with symlinks (such as /vendor >/system/vendor ) when absent.

Android 8.0 makes the vendor partition mandatory

The goal is to modularize Android partitions with standard interface between
the Android Platform (on system.img ) and vendor-provided code(on vendor.img).

This standard interface enables the Android Platform to be updated
without affecting the SoC partitions. This makes it possible to upgrade a
device system.img from Android 8.0 to Android P while other images (such as
vendor.img) remain at Android 8.0. This modularity enables timely
Android platform upgrades (such as monthly security updates )
without requiring SoC/ODM partners to update SoC- and device-specific code.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

cmd: Move CONFIG_RANDOM_UUID to Kconfig

CONFIG_RANDOM_UUID is used by the GPT command to generate random UUID when
none are provided.

Move that option to Kconfig.

Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

arm: dra7xx: Fix Linux boot from eMMC

Right now on OMAP5-based boards we have only one partition defined for
Linux boot, which is rootfs. That doesn't work with bootpart=1:2 (that
is defined in include/environment/ti/boot.h). To fix Linux boot we may
either:

1. Change bootpart to be 1:1
2. Or add preceding partition, so that rootfs is actually 1:2

Second choice seems more reasonable, as DFU is already using similar
partition table and can rely on bootpart to be 1:2.

This patch adds "bootloader" partition. So now eMMC layout for Linux
boot looks like this:

offset content size partition
(KiB) (KiB)
Reviewed-by: Tom Rini <trini@konsulko.com>

=======================================================================

0 +--------------------------------+
| MBR/GPT header | 128 -
128 +--------------------------------+
| MLO | 256 -
384 +--------------------------------+
| u-boot.img | 1792 bootloader
2176 +--------------------------------+
| //////////// hole //////////// | 256 -
2432 +--------------------------------+
| U-Boot environment | 128 -
2560 +--------------------------------+
| U-Boot environment (redundant) | 128 -
2688 +--------------------------------+
| rootfs | remaining rootfs
end +--------------------------------+

=======================================================================

Guard hole appears because U-Boot environment offset was calculated for
Android partition table, which has two additional partitions in place of
that hole ("environment" and "misc" partitions).

This patch also changes rootfs offset from 2 MiB further to 2688 KiB,
so that there won't be any collisions with U-Boot environment when we
flash rootfs.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

Kconfig: Migrate all of cmd/fastboot/Kconfig to defconfigs

- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's
not strictly part of fastboot.
- Add some defaults for the fastboot buffer location and size
- Migrate all options listed in cmd/fastboot/Kconfig
- Cleanup the README

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_OMAP3_SPI to Kconfig

This converts the following to Kconfig:
CONFIG_OMAP3_SPI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Minor comment tweaks]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CMD_SPL_WRITE_SIZE to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SPL_WRITE_SIZE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Convert CONFIG_CMD_SPL_NAND_OFS to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SPL_NAND_OFS

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

configs: Finish migration of PHY_GIGE

Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Move PHYLIB to Kconfig

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs: Remove CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS in all boards

Now that xHCD does not use CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>

Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_ENV_IS_IN_FLASH to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SCSI to Kconfig

This converts the following to Kconfig:
CONFIG_SCSI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

arm: dra7: Increase "bootloader" partition size

Increase the size of u-boot.img, so that it conforms with new DFU
configuration (see commit [1]).

[1] 7a53a1a8115b ARM: ti: Update layout for MMC and eMMC (env and dfu)

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

ARM: ti: Update layout for MMC and eMMC (env and dfu)

The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area (2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region
"spl-os-image.raw".
both: region "spl-os-image.raw" is quite small and can't handle android
kernels

Fixing this requires growing some regions and moving others.
Care has been taken to leave some room for further growth of
"spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the
region is not free space that can be used to grow "u-boot.img.raw".
The MLO region is 0x100 sectors wide but the 0x100 are unused in case the
MLO comes too overflow this areas.
The total space allocated for those raw binaries is 16MB, of which 13+MB
are reserved for the kernel image.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>

Convert CONFIG_CMD_EEPROM et al to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRING

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>

arm: dra7xx: move CONFIG_DRA7XX to Kconfig

The symbol CONFIG_DRA7XX is needed for Kconfig conditions.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>

configs: dra7xx_evm: Enable SPL_DM

Enable SPL_DM on all DRA7 based platforms.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

ARM: Use Kconfig for board EEPROM's I2C bus and chip address

In stead of defining the board EEPROM address in the board headers
let's define them in the board config files and make them
configurable by Kconfig.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Kconfig: Migrate CONFIG_BAUDRATE

Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

flash: complete CONFIG_SYS_NO_FLASH move with renaming

We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

cmd, disk: convert CONFIG_PARTITION_UUIDS, CMD_PART and CMD_GPT

We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_EFI_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig

This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>

config: Move CONFIG_BOARD_LATE_INIT to defconfigs

Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>

ARM: ti: consolidate dfu environment variables

Introduce include/environment/ti/dfu.h that
consolidates environment variable definitions
for various TI boards that support DFU today.

Tested on AM335x EVM, AM437x SK EVM and DRA74x
EVM by using DFU to write to SD card.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

spl: dfu: move DFU Kconfig to SPL Kconfig

The DFU Kconfig menu entries should be part of the SPL
Kconfig file. Also avoid using the top level Makefile by
moving the config dependent build artifacts to the driver/
and driver/usb/gadget/ Makfiles.

With that, DFU can be built again in SPL if
CONFIG_SPL_DFU_SUPPORT is enabled.

Fixes: 6ad6102246d8 ("usb:gadget: Disallow DFU in SPL for now")

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>

arm: dra7xx: Unify Android partition table

Make Android partition table the same as for AM57x EVM.

1. Make "bootloader" partition start from 0x300 sectors offset, so
DRA7 is bootable in Android mode (see
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR option).
2. Increase "bootloader" partition size, because size of u-boot.img is
about 632 KiB (when building DT defconfig, with FIT image enabled).
3. Specify "reserved" partition explicitly, rather than specifying
"efs" partition start. Reserved area will be used to store U-Boot
environment on eMMC. It's convenient to have it exposed explicitly
so we can read/write U-Boot environment.
4. Keep all Android partitions locations intact, by reducing
"reserved" partition size. CONFIG_ENV_SIZE is considered.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

dra7x: dfu: qspi: increase the qspi spl partition to 256K

The SPL size for dra7x platform increased beyond 64K,
increasing the size to 256K to cater for future enhancement.

Signed-off-by: Ravi Babu <ravibabu@ti.com>

dra7xx: config: cleanup: moved to kconfig for CONFIG_SPL_ENV_SUPPORT

removing CONFIG_SPL_ENV_SUPPORT defined in header files
due to moved to kconfig option for CONFIG_SPL_ENV_SUPPORT

Signed-off-by: Ravi Babu <ravibabu@ti.com>

arm: dra7xx: Move fastboot options to defconfig

Now that fastboot options are available in Kconfig, we can migrate them
from DRA7 header to corresponding DRA7 defconfigs.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

Merge branch 'master' of git://git.denx.de/u-boot-usb

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
include/configs/dra7xx_evm.h

dra7x: configs: enable SPL-DFU support

This patch enables the SPL-DFU support for
dra7x platform.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

dfu: Migrate to Kconfig

Introduce a hidden USB_FUNCTION_DFU Kconfig option and select it for
CMD_DFU (as we must have the DFU command enabled to do anything DFU).
Make all of the entries in drivers/dfu/Kconfig depend on CMD_DFU and add
options for all of the back end choices that DFU can make use of.

Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>

Convert CONFIG_SPL_SPI_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_SPI_FLASH_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_MMC_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_ENV_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_DMA_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Migrate CONFIG_USB_STORAGE

In some cases we were missing CONFIG_USB=y so enable that when needed.

Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

TI: Rework SRAM definitions and maximums

On all TI platforms the ROM defines a "downloaded image" area at or near
the start of SRAM which is followed by a reserved area. As it is at
best bad form and at worst possibly harmful in corner cases to write in
this reserved area, we stop doing that by adding in the define
NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image
area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this.
At current we define the end of scratch space at 0x228 bytes past the
start of scratch space this this gives us a lot of room to grow. As
these scratch uses are non-optional today, all targets are modified to
respect this boundary.

Tested on OMAP4 Pandaboard, OMAP3 Beagle xM

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Weber <weber@corscience.de>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: "B, Ravi" <ravibabu@ti.com>
Cc: "Matwey V. Kornilov" <matwey.kornilov@gmail.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: "Kipisz, Steven" <s-kipisz2@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>

usb: add (move) CONFIG_USB_HOST to Kconfig

The meaning of CONFIG_USB in U-Boot is different from that in Linux.

As you see in drivers/usb/Kconfig of Linux, CONFIG_USB enables the
USB host controller support, while CONFIG_USB_SUPPORT is used to
enable the whole of the USB sub-system.

When I added CONFIG_USB into Kconfig by commit 6e7e9294d321 ("usb:
add basic USB configs in Kconfig"), I planned to follow the Linux's
convention, i.e. CONFIG_USB to enable/disable the USB host support.

Then, commit 68f7c5db2d1e ("usb: Generic USB Kconfig option, that
fits both host and gadget and comments") changed the logic of the
CONFIG_USB to point to the whole of the USB sub-system. As a result,
currently we do not have an option for USB host.

This commit adds CONFIG_USB_HOST, which will be useful to compile
in the USB host support code.

CONFIG_USB_HOST is not referenced at all, but strangely some boards
define it in board headers. I removed them because USB_HOST will be
selected in Kconfig going forward.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

treewide: move CONFIG_PHYS_64BIT to Kconfig

We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system. Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.

Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6d4 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.

I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable. However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.

CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.

Fixes: 95ebc253e6d4 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>

configs: dra7xx: Update QSPI speed to 76.8MHz

Now that QSPI driver can support 76.8MHz, update the
CONFIG_SF_DEFAULT_SPEED to the same value.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>

usb: move CONFIG_USB_XHCI_DWC3 to Kconfig

Create an entry for "config USB_XHCI_DWC3" in Kconfig and
switch over to it for all boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

usb: move CONFIG_USB_XHCI to Kconfig with renaming

Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it
into CONFIG_USB_XHCI_HCD.

As commented in the help of "config USB_XHCI" entry, this has been
a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI
have been unified in favor of the former.

Note:
Some boards define CONFIG_USB_XHCI in their headers without
CONFIG_USB, which does not meet the "depends on" in Kconfig.
I added CONFIG_USB=y for those boards when converting.
Otherwise, they would fail to build.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

dm: scsi: Rename CONFIG_CMD_SCSI to CONFIG_SCSI

This option currently enables both the command and the SCSI functionality.
Rename the existing option to CONFIG_SCSI since most of the code relates
to the feature.

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

usb: gadget Move: CONFIG_G_DNL_* to Kconfig

And also reformat defconfigs using "make savedefconfig" rule.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

usb: dwc3: Move CONFIG_USB_DWC3_PHY_* to Kconfig

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

usb: dwc3: Move CONFIG_USB_DWC3_OMAP to Kconfig

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

usb: dwc3: Move CONFIG_USB_DWC3_GADGET/HOST to Kconfig

Description was borrowed from kernel dwc3 Kconfig.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

usb: gadget: Move CONFIG_USB_GADGET_DOWNLOAD to Kconfig

While at it, remove obsolete CONFIG_USBDOWNLOAD_GADGET option from some
config headers. This is also probably fixes am335x_baltos board.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

usb: gadget: Move CONFIG_USB_GADGET_DUALSPEED to Kconfig

Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and
make all UDC controllers select USB_GADGET_DUALSPEED:
- add next options to Kconfig selecting USB_GADGET_DUALSPEED:
- USB_GADGET_ATMEL_USBA
- USB_GADGET_DWC2_OTG
- USB_DWC3
- CI_UDC
- make USB_MUSB_GADGET select USB_GADGET_DUALSPEED

While at it, make some related fixes:
- remove DUALSPEED from configs that don't enable gadget support:
- kwb.h
- tseries.h
- add missing USB_GADGET option to next configs:
- novena_defconfig
- pcm051_rev*_defconfig
- xfi3_defconfig

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

usb: gadget: Move CONFIG_USB_GADGET_VBUS_DRAW to Kconfig

The description was borrowed from kernel. Definitions were added to
defconfig files in a way that "make savedefconfig" generates exactly
the same file as used defconfig.

Boards using 0 mA as CONFIG_USB_GADGET_VBUS_DRAW value were moved to use
2 mA (as minimal allowed by Kconfig).

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

board: ti: DRA7: Add DP83867 TI phy for rev c

Enable the TI DP83867 Giga bit phy on the
dra7 rev c board. The rx and tx internal
delays are need for this board so the usage
of RGMII_ID is required.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>