thunderbolt: Avoid notify PM core about runtime PM resume

Currently we notify PM core about occurred wakes after any resume. This
is not actually needed after resume from runtime suspend. Hence, notify
PM core about occurred wakes only after resume from system sleep. Also,
if the wake occurred in USB4 router upstream port, we don't notify the
PM core about it since it is not actually needed and can cause
unexpected autowake (e.g. if /sys/power/wakeup_count is used).

While there add the missing kernel-doc for tb_switch_resume().

Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Fix wake configurations after device unplug

Currently we don't configure correctly the wake events after unplug of device
router. What can happen is that the downstream ports of host router will be
configured to wake on: USB4-wake and wake-on-disconnect, but not on
wake-on-connect. This may cause the later plugged device not to wake the
domain and fail in enumeration. Fix this by clearing downstream port's "USB4
Port is Configured" bit, after unplug of a device router.

Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Constify the struct device_type usage

Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the
tb_domain_type, tb_retimer_type, tb_switch_type, usb4_port_device_type,
tb_service_type and tb_xdomain_type variables to be constant structures as
well, placing it into read-only memory which can not be modified at
runtime.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Remove usage of the deprecated ida_simple_xx() API

ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().

Note that the upper limit of ida_simple_get() is exclusive, but the one of
ida_alloc_range()/ida_alloc_max() is inclusive. So a -1 has been added
when needed.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Fix rollback in tb_port_lane_bonding_enable() for lane 1

If enabling lane bonding on lane 1 of a USB4 port results in an error,
the rollback should set TB_LINK_WIDTH_SINGLE for both lanes.

Signed-off-by: Mohammad Rahimi <rahimi.mhmmd@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Make tb_switch_reset() support Thunderbolt 2, 3 and USB4 routers

Currently tb_switch_reset() only did something for Thunderbolt 1
devices. Expand this to support all generations, including USB4, and
both host and device routers.

Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Introduce tb_port_reset()

Introduce a function that issues Downstream Port Reset to a USB4 port.
This supports Thunderbolt 2, 3 and USB4 routers.

Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Fix NULL pointer dereference in tb_port_update_credits()

Olliver reported that his system crashes when plugging in Thunderbolt 1
device:

BUG: kernel NULL pointer dereference, address: 0000000000000020
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:tb_port_do_update_credits+0x1b/0x130 [thunderbolt]
Call Trace:
<TASK>
? __die+0x23/0x70
? page_fault_oops+0x171/0x4e0
? exc_page_fault+0x7f/0x180
? asm_exc_page_fault+0x26/0x30
? tb_port_do_update_credits+0x1b/0x130
? tb_switch_update_link_attributes+0x83/0xd0
tb_switch_add+0x7a2/0xfe0
tb_scan_port+0x236/0x6f0
tb_handle_hotplug+0x6db/0x900
process_one_work+0x171/0x340
worker_thread+0x27b/0x3a0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x31/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>

This is due the fact that some Thunderbolt 1 devices only have one lane
adapter. Fix this by checking for the lane 1 before we read its credits.

Reported-by: Olliver Schinagl <oliver@schinagl.nl>
Closes: https://lore.kernel.org/linux-usb/c24c7882-6254-4e68-8f22-f3e8f65dc84f@schinagl.nl/
Fixes: 81af2952e606 ("thunderbolt: Add support for asymmetric link")
Cc: stable@vger.kernel.org
Cc: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Keep link as asymmetric if preferred by hardware

In case of the link is brought up as asymmetric (due to hardware preference), we
honor that and don't transition it to symmetric, unless a router with symmetric
link got plugged below, in the topology (and a bandwidth allows transition to
symmetric).

Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Move width_name() helper to tb.h

We are going to use it in subsequent patches, so make it available outside of
switch.c. Also, change the name to tb_width_name() to follow the naming
conventions.

Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Send uevent after asymmetric/symmetric switch

We should send uevent to userspace whenever the link speed or width
changes but tb_switch_asym_enable() and tb_switch_asym_disable() set the
sw->link_width already so tb_switch_update_link_attributes() never
noticed the change.

Fix this so that we let tb_switch_update_link_attributes() update the
fields accordingly.

Fixes: 81af2952e606 ("thunderbolt: Add support for asymmetric link")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Set lane bonding bit only for downstream port

Fix the lane bonding procedure to follow the steps described in USB4
Connection Manager guide. Hence, set the lane bonding bit only for
downstream port. This is needed for certain ASMedia device, otherwise
lane bonding fails and the device disconnects.

Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add support for asymmetric link

USB4 v2 spec defines a Gen 4 link that can operate as an aggregated
symmetric (80/80G) or asymmetric (120/40G). When the link is asymmetric,
the USB4 port on one side of the link operates with three TX lanes and
one RX lane, while the USB4 port on the opposite side of the link
operates with three RX lanes and one TX lane.

Add support for the asymmetric link and provide functions that can be
used to transition the link to asymmetric and back.

Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Make is_gen4_link() available to the rest of the driver

Rework the function to return the link generation, update the name to
tb_port_get_link_generation(), and make available to the rest of the
driver. This is needed in the subsequent patches.

Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Log NVM version of routers and retimers

This is useful when debugging possible issues.

Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Fix typo of HPD bit for Hot Plug Detect

Fix typo of HPD bit stands for Hot Plug Detect.

Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Check that lane 1 is in CL0 before enabling lane bonding

Marek reported that when BlackMagic UltraStudio device is connected the
kernel repeatedly tries to enable lane bonding without success making
the device non-functional. It looks like the device does not have lane 1
connected at all so even though it is enabled we should not try to bond
the lanes. For this reason check that lane 1 is in fact CL0 (connected,
active) before attempting to bond the lanes.

Reported-by: Marek Šanta <teslan223@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217737
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Check Intel vendor ID in tb_switch_get_generation()

Only Intel made Thunderbolt 1-3 devices so to avoid possible confusion
check for the Intel vendor ID before deciding the device generation.
While there move the USB4 check to happen first.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add support for enhanced uni-directional TMU mode

This is new TMU mode introduced with the USB4 v2. This mode is simpler
than the existing ones and allows all CL states as well. Enable this for
all links where both side routers are v2 and keep the existing
functionality for the v1 and earlier links.

Currently only support the MedRes rate. We can add the HiFi rate later
too if it turns out to be useful.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Announce USB4 v2 connection manager support

Program the CMUV (Connection Manager USB4 Version) field for USB4 v2 and
v1 routers according to the spec.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add support for USB4 v2 80 Gb/s link

USB4 v2 bumps the per-lane speed up to 40 Gb/s. Also the lanes are
always bonded which gives 80 Gb/s symmetric link (and 120/40 Gb/s
asymmetric). This updates the speed and width of routers and XDomain
connections to support the Gen 4 link. For now we keep the link as is
even if it is already asymmetric.

While there make tb_port_set_link_width() static.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Identify USB4 v2 routers

Add a new function usb4_switch_version() that can be used to figure out
the spec version of the router and make tb_switch_is_usb4() to use it as
well. Update the uevent accordingly.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Do not touch lane 1 adapter path config space

It is not required to be implemented at all because USB4 does not use
lane 1 for tunneling except when aggregated with lane 0. For this reason
do not try to read the path config space of USB4 lane 1 adapters.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Initialize CL states from the hardware

In case the boot firmware enabled any of them, read the currently
configured CL states and update the router structure accordingly.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Switch CL states from enum to a bitmask

This is more natural and follows the hardware register layout better.
This makes it easier to see which CL states we enable (even though they
should be enabled together). Rename 'clx_mask' to 'clx' everywhere as
this is now always bitmask.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Move CLx support functions into clx.c

There really don't belong to switch.c so move them into their own file.
As we do this rename the functions to match the conventions used
elsewhere in the driver.

No functional changes.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Introduce tb_switch_downstream_port()

Introduce tb_switch_downstream_port() helper function that returns the
downstream port of a parent switch that is connected to the upstream
port of specified switch. From now on, we use it all across the driver
where applicable.

While there fix a whitespace in comment and rename 'downstream' to
'down' to be consistent with the rest of the driver.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Get rid of redundant 'else'

In the snippets like the following

if (...)
return / goto / break / continue ...;
else
...

the 'else' is redundant. Get rid of it.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Call tb_check_quirks() after initializing adapters

In order to apply quirks based on certain adapter types move call to
tb_check_quirks() happen after the adapters are initialized. This should
not affect the existing quirks.

Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

driver core: make struct device_type.uevent() take a const *

The uevent() callback in struct device_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.

Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Gross <markgross@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sean Young <sean@mess.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Won Chung <wonchung@google.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for Thunderbolt
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Take CL states into account when waiting for link to come up

If CL states are enabled for the link it may be in these states too when
reading the lane adapter state but it will enter CL0 as soon as there is
traffic in the high-speed lanes. Upon discovery we want to make sure
that is accounted as the link being up, otherwise we end up tearing down
the topology with no good reason.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Use str_enabled_disabled() helper

Use str_enabled_disabled() helper instead of open coding the same.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Explicitly enable lane adapter hotplug events at startup

Software that has run before the USB4 CM in Linux runs may have disabled
hotplug events for a given lane adapter.

Other CMs such as that one distributed with Windows 11 will enable hotplug
events. Do the same thing in the Linux CM which fixes hotplug events on
"AMD Pink Sardine".

Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Convert to use sysfs_emit()/sysfs_emit_at() APIs

Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the value
to be returned to user space.

While at it, use Elvis operator in some cases.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Move vendor specific NVM handling into nvm.c

As there will be more USB4 devices that support NVM firmware upgrade from
various vendors, it makes sense to split out the Intel specific NVM
image handling from the generic code. This moves the Intel specific NVM
handling into a new structure that will be matched by the device type
and the vendor ID. Do this for both routers and retimers.

This makes it easier to extend the NVM support to cover new vendors and
NVM image formats in the future.

Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Rename and make nvm_read() available for other files

In order to support non-Intel NVM formats the vendor specific NVM
validation code that will live in nvm.c needs to be able to read various
parts of the NVM so make the function available outside of switch.c and
rename it accordingly.

Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Extend NVM version fields to 32-bits

In order to support non-Intel NVM image formats extend the NVM major and
minor version to 32-bits to better accommondate different versioning
schemes.

No functional impact.

Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add helper to check if CL states are enabled on port

We will need this when enabling lane margining support.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Pass CL state bitmask to tb_port_clx_supported()

Instead of testing just a single CL state we can pass a bitmask of
states to check. This makes it simpler for callers of the function.

We also add a check for CL2 even though not fully supported by the
driver yet.

Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Move port CL state functions into correct place in switch.c

They should be close to other functions dealing with USB4 ports. No
functional impact.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Explicitly reset plug events delay back to USB4 spec value

If any software has interacted with the USB4 registers before the Linux
USB4 CM runs, it may have modified the plug events delay. It has been
observed that if this value too large, it's possible that hotplugged
devices will negotiate a fallback mode instead in Linux.

To prevent this, explicitly align the plug events delay with the USB4
spec value of 10ms.

Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Check router generation before connecting xHCI

Only Thunderbolt 3 routers need the xHCI connection flow. This also
ensures the router actually has both lane adapters (1 and 3). While
there move declaration of the boolean variables inside the block where
they are being used.

Fixes: 30a4eca69b76 ("thunderbolt: Add internal xHCI connect flows for Thunderbolt 3 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add CL1 support for USB4 and Titan Ridge routers

In this patch we add support for a second low power state of the link: CL1.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle.
We enable it, if both sides of the link support it,
and only for the first hop router (i.e. the first device that connected
to the host router). This is needed for better thermal management.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Fix typos in CLx enabling

Fix few typos in CLx enabling.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: CLx disable before system suspend only if previously enabled

Disable CLx before system suspended only if previously was enabled.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Ignore port locked error in tb_port_wait_for_link_width()

Sometimes when polling for the port after target link width is changed
we get back port locked notification (because the link actually was
reset and then re-trained). Instead of bailing out we can ignore these
when polling for the width change as this is expected.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Split setting link width and lane bonding into own functions

When bonding lanes over XDomain the host that has "higher" UUID triggers
link re-train for bonding, and the host that has "lower" UUID just waits
for this to happen. To support this split setting the link width and
triggering the actual bonding a separate functions that can be called as
needed.

While there remove duplicated empty line in the kernel-doc comment of
tb_port_lane_bonding_disable().

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add debug logging when lane is enabled/disabled

This is useful when debugging possible issues.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Do not make DROM read success compulsory

The USB4 specification doesn't make any requirements that reading
a device router's DROM is needed for the operation of the device.

Other connection manager solutions don't necessarily read it or gate
the usability of the device on whether it was read.

So make failures when reading the DROM show warnings but not
fail the initialization of the router.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Do not resume routers if UID is not set

Routers might not have a UID set if the DROM read failed during
initialization previously.

Normally upon resume the UID is re-read to confirm it's the same
device connected.
* If the DROM read failed during init but then succeeded during
resume it could either be a new device or faulty device
* If the DROM read failed during init and also failed during resume
it might be a different device plugged in all together.

Detect this situation and prevent re-using the same configuration in
these cirucmstances.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add internal xHCI connect flows for Thunderbolt 3 devices

Both Alpine Ridge and Titan Ridge require special flows in order to
activate the internal xHCI controller when there is USB device connected
to the downstream type-C port. This implements the missing flows for
both.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add module parameter for CLx disabling

Add a module parameter that allows user to completely disable CLx
functionality in case problems are found.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Enable CL0s for Intel Titan Ridge

Low power link states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. The
simplest one being called CL0s. Follow what we already do for USB4
device routers and enable CL0s for Intel Titan Ridge device router too.
This allows better thermal management.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Implement TMU time disruption for Intel Titan Ridge

Intel Titan Ridge based routers have slightly different flow for time
disruption than USB4 compliant routers. This makes it work on Titan
Ridge too. Needed to enable link low power states on Titan Ridge.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Move usb4_switch_wait_for_bit() to switch.c

Currently usb4_switch_wait_for_bit() used only in usb4.c Moving to
switch.c to call it from other files. Also change the prefix to "tb_"
to follow to the naming convention.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add CL0s support for USB4 routers

In this patch we add enabling of CL0s - a low power state of the link.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. For now,
we add support only for first low power state: CL0s. We enable it, if
both sides of the link support it, and only for the first hop router.
(i.e. the first device that connected to the host router). This is
needed for better thermal management.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add debug logging of DisplayPort resource allocation

Add more debugging around DP resource allocation/de-allocation.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Do not program path HopIDs for USB4 routers

These fields are marked read-only for USB4 routers so do not touch them
in that case. Update the kernel-doc of tb_dp_port_set_hops() to reflect
this too.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Do not allow subtracting more NFC credits than configured

This might happen if the boot firmware uses different amount of NFC
credits than what the router suggests, or we are dealing with pre-USB4
device.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Fix port linking by checking all adapters

In tb_switch_default_link_ports(), while linking of ports,
only odd-numbered ports (1,3,5..) are considered and even-numbered
ports are not considered.

AMD host router has lane adapters at 2 and 3 and link ports at adapter 2
is not considered due to which lane bonding gets disabled.

Hence added a fix such that all ports are considered during
linking of ports.

Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Do not read control adapter config space

Adapter 0 is the control adapter and as per USB4 spec in section 2.2.6.2
control Adapters do not have an adapter configuration space.

For this reason skip reading adapter config space in tb_port_init() when
the port number is 0. This actually simplifies the rest of the function
as we don't need to check for the port->port == 0 anymore.

While there drop the extra empty line at the end of the function.

Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add authorized value to the KOBJ_CHANGE uevent

For security reasons, we would like to monitor and track when the
Thunderbolt devices are authorized and deauthorized (i.e. when the
Thunderbolt sysfs "authorized" attribute changes). Currently the
userspace gets a udev change notification when there is a change, but
the state may have changed (again) by the time we look at the authorized
attribute in sysfs. So an authorization event may go unnoticed. Thus
make it easier by informing the actual change (new value of authorized
attribute) in the udev change notification.

The change is included as a key value "authorized=<val>" where <val>
is the new value of sysfs attribute "authorized", and is described at
Documentation/ABI/testing/sysfs-bus-thunderbolt under
/sys/bus/thunderbolt/devices/.../authorized.

Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Revert "thunderbolt: Hide authorized attribute if router does not support PCIe tunnels"

This reverts commit 6f3badead6a078cf3c71f381f9d84ac922984a00.

It turns out bolt depends on having authorized attribute visible under
each device. Hiding it makes bolt crash as several people have reported
on various bug trackers. For this reason revert the commit.

Link: https://gitlab.freedesktop.org/bolt/bolt/-/issues/174
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1979765
Link: https://bugs.archlinux.org/task/71569
Cc: stable@vger.kernel.org
Cc: Christian Kellner <ckellner@redhat.com>
Fixes: 6f3badead6a0 ("thunderbolt: Hide authorized attribute if router does not support PCIe tunnels")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20210727142501.27476-1-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Allow router NVM authenticate separately

It may be useful if the actual NVM authentication can be delayed to be
run later, for instance when the user logs out. For this reason add a
new NVM operation (AUHENTICATE_ONLY) that just triggers the authentication
procedure over whatever was written to the NVM storage.

This is not supported with Thunderbolt 1-3 devices, though.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Move nvm_write_ops to tb.h

Currently these write ops are used for updating router firmware images
only. Moving to tb.h helps the retimers also to use the same ops.

Also add tb_ prefix to the enum while there.

Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add support for retimer NVM upgrade when there is no link

With help from platform firmware (ACPI) it is possible to power on
retimers even when there is no USB4 link (e.g nothing is connected to
the USB4 ports). This allows us to bring the USB4 sideband up so that we
can access retimers and upgrade their NVM firmware.

If the platform has support for this, we expose two additional
attributes under USB4 ports: offline and rescan. These can be used to
bring the port offline, rescan for the retimers and put the port online
again. The retimer NVM upgrade itself works the same way than with cable
connected.

Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add USB4 port devices

Create devices for each USB4 port. This is needed when we add retimer
access when there is no device connected but may be useful for other
purposes too following what USB subsystem does. This exports a single
attribute "link" that shows the type of the USB4 link (or "none" if
there is no cable connected).

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Update port credits after bonding is enabled/disabled

Once lane bonding has been enabled (or disabled) both lane adapters may
update their total credits accordingly. For this reason re-read the port
credits after lane bonding has been enabled or disabled.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Read router preferred credit allocation information

USB4 routers must expose their preferred credit (buffer) allocation
information through router operation. This information tells the
connection manager how the router prefers its buffers to be allocated to
get the expected bandwidth for the supported protocols.

Read this information and store it as part of struct tb_switch for each
USB4 router.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Wait for the lanes to actually bond

It may take some time until the two lanes enter bonded state so poll for
the link width to match what is expected before going forward. This ensures
the link is in expected state before we start establishing paths through
it.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Make tb_port_type() take const parameter

The function does not modify the object in any way so make the parameter
const to reflect this.

No functional changes intended.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add wake from DisplayPort

Latest USB4 spec added a new wake bit for DisplayPort so add this to the
driver when runtime suspending. This way wake up the domain when a new
monitor is plugged in to any of the device routers.

Also do the same for pre-USB4 devices through the link controller
registers as documented in chapter 13 of the USB4 spec.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Hide authorized attribute if router does not support PCIe tunnels

With USB4 devices PCIe tunneling is optional so for device routers
without PCIe upstream adapter it does not make much sense to expose the
authorized attribute. For this reason hide it if PCIe tunneling is not
supported by the device router.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add details to router uevent

Expose two environment variables for routers as part of the initial
uevent:

USB4_VERSION=1.0
USB4_TYPE=host|device|hub

Userspace can use this information to expose more details about each
connected device. Only USB4 devices have USB4_VERSION but all devices
have USB4_TYPE.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Check quirks in tb_switch_add()

This makes it more visible on the main path of adding router.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Drop unused tb_port_set_initial_credits()

This function is not used anymore in the driver so we can remove it.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Do not pass timeout for tb_cfg_reset()

There is only one user for this function and it passes the default
timeout to it anyway, so remove the parameter completely. This is also
needed in the subsequent patch where we allow connection manager
implementations to use different timeout for non-raw control channel
messages.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Initialize HopID IDAs in tb_switch_alloc()

If there is a failure before the tb_switch_add() is called the switch
object is released by tb_switch_release() but at that point HopID IDAs
have not yet been initialized. So we see splat like this:

BUG: spinlock bad magic on CPU#2, kworker/u8:5/115
...
Workqueue: thunderbolt0 tb_handle_hotplug
Call Trace:
dump_stack+0x97/0xdc
? spin_bug+0x9a/0xa7
do_raw_spin_lock+0x68/0x98
_raw_spin_lock_irqsave+0x3f/0x5d
ida_destroy+0x4f/0x127
tb_switch_release+0x6d/0xfd
device_release+0x2c/0x7d
kobject_put+0x9b/0xbc
tb_handle_hotplug+0x278/0x452
process_one_work+0x1db/0x396
worker_thread+0x216/0x375
kthread+0x14d/0x155
? pr_cont_work+0x58/0x58
? kthread_blkcg+0x2e/0x2e
ret_from_fork+0x1f/0x40

Fix this by always initializing HopID IDAs in tb_switch_alloc().

Fixes: 0b2863ac3cfd ("thunderbolt: Add functions for allocating and releasing HopIDs")
Cc: stable@vger.kernel.org
Reported-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add support for PCIe tunneling disabled (SL5)

Recent Intel Thunderbolt firmware connection manager has support for
another security level, SL5, that disables PCIe tunneling. This option
can be turned on from the BIOS.

When this is set the driver exposes a new security level "nopcie" to the
userspace and hides the authorized attribute under connected devices.

While there we also hide it when "dponly" security level is enabled
since it is not really usable in that case anyway.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>

thunderbolt: switch: Fix kernel-doc descriptions of non-static functions

Fix kernel-doc descriptions of all non-static functions. This also gets
rid of the warnings on W=1 build.

Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lee Jones <lee.jones@linaro.org>

thunderbolt: switch: Fix function name in the header

Fixes the following W=1 kernel build warning(s):

drivers/thunderbolt/switch.c:1322: warning: expecting prototype for reset_switch(). Prototype was for tb_switch_reset() instead

Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: switch: Demote a bunch of non-conformant kernel-doc headers

Fixes the following W=1 kernel build warning(s):

drivers/thunderbolt/switch.c:730: warning: Function parameter or member 'port' not described in 'tb_init_port'
drivers/thunderbolt/switch.c:1348: warning: Function parameter or member 'sw' not described in 'tb_plug_events_active'
drivers/thunderbolt/switch.c:1348: warning: Function parameter or member 'active' not described in 'tb_plug_events_active'

Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[ mw: Demote only static functions ]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add support for de-authorizing devices

In some cases it is useful to be able de-authorize devices. For example
if user logs out the userspace can have a policy that disconnects PCIe
devices until logged in again. This is only possible for software based
connection manager as it directly controls the tunnels.

For this reason make the authorized attribute accept writing 0 which
makes the software connection manager to tear down the corresponding
PCIe tunnel. Userspace can check if this is supported by reading a new
domain attribute deauthorization, that holds 1 in that case.

While there correct tb_domain_approve_switch() kernel-doc and
description of authorized attribute to mention that it is only about
PCIe tunnels.

Cc: Christian Kellner <christian@kellner.me>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>

thunderbolt: Start lane initialization after sleep

USB4 spec says that for TBT3 compatible device routers the connection
manager needs to set SLI (Start Lane Initialization) to get the lanes
that were not connected back to functional state after sleep. Same needs
to be done if the link was XDomain.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>

thunderbolt: Constify static attribute_group structs

The only usage of these is to put their addresses in arrays of pointers
to const attribute_groups. Make them const to allow the compiler to put
them in read-only memory.

Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Perform USB4 router NVM upgrade in two phases

The currect code expects that the router returns back the status of the
NVM authentication immediately. When tested against a real USB4 device
what happens is that the router is reset and only after that the result
is updated in the ROUTER_CS_26 register status field. This also seems to
align better what the spec suggests.

For this reason do the same what we already do with the Thunderbolt 3
devices and perform the NVM upgrade in two phases. First start the
NVM_AUTH router operation and once the router is added back after the
reset read the status in ROUTER_CS_26 and expose it to the userspace
accordingly.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add functions for enabling and disabling lane bonding on XDomain

These can be used by service drivers to enable and disable lane bonding
as needed.

Signed-off-by: Isaac Hazan <isaac.hazan@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add link_speed and link_width to XDomain

Link speed and link width are needed for checking expected values in
case of using a loopback service.

Signed-off-by: Isaac Hazan <isaac.hazan@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add debugfs interface

This adds debugfs interface that can be used for debugging possible
issues in hardware/software. It exposes router and adapter config spaces
through files like this:

/sys/kernel/debug/thunderbolt/<DEVICE>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/path
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/counters
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/path
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/counters
...

The "regs" is either the router or port configuration space register
dump. The "path" is the port path configuration space and "counters" is
the optional counters configuration space.

These files contains one register per line so it should be easy to use
normal filtering tools to find the registers of interest if needed.

The router and adapter regs file becomes writable when
CONFIG_USB4_DEBUGFS_WRITE is enabled (which is not supposed to be done
in production systems) and in this case the developer can write "offset
value" lines there to modify the hardware directly. For convenience this
also supports the long format the read side produces (but ignores the
additional fields). The counters file can be written even when
CONFIG_USB4_DEBUGFS_WRITE is not enabled and it is only used to clear
the counter values.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Introduce tb_port_is_nhi()

This is useful if one needs to check if adapter (port) is the host
interface (NHI). Make tb_port_alloc_hopid() take advantage of this.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add runtime PM for Software CM

This adds runtime PM support for the Software Connection Manager parts
of the driver. This allows to save power when either there is no device
attached at all or there is a device attached and all following
conditions are true:

- Tunneled PCIe root/downstream ports are runtime suspended
- Tunneled USB3 ports are runtime suspended
- No active DisplayPort stream
- No active XDomain connection

For the first two we take advantage of device links that were added in
previous patch. Difference for the system sleep case is that we also
enable wakes when something is geting plugged in/out of the Thunderbolt
ports.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Enable wakes from system suspend

In order for the router and the whole domain to wake up from system
suspend states we need to enable wakes for the connected routers. For
device routers we enable wakes from PCIe and USB 3.x. This allows
devices such as keyboards connected to USB 3.x hub that is tunneled to
wake the system up as expected. For all routers we enabled wake on USB4
for each connected ports. This is used to propagate the wake from router
to another.

Do the same for legacy routers through link controller vendor specific
registers as documented in USB4 spec chapter 13.

While there correct kernel-doc of usb4_switch_set_sleep() -- it does not
enable wakes instead there is a separate function (usb4_switch_set_wake())
that does.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Disable lane 1 for XDomain connection

USB4 spec mandates that the lane 1 should be disabled if lanes are not
bonded. For host-to-host connections (XDomain) we don't support lane
bonding so in order to be compatible with the spec, disable lane 1 when
another host is connected.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Set port configured for both ends of the link

Both ends of the link needs to have this set. Otherwise the link is not
re-established properly after sleep. Now since it is possible to have
mixed USB4 and Thunderbolt 1, 2 and 3 devices we need to split the link
configuration functionality to happen per port so we can pick the
correct implementation.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Configure link after lane bonding is enabled

During testing it was noticed that the link is not properly restored
after the domain exits sleep if the link configured bits are set before
lane bonding is enabled. The USB4 spec does not say in which order these
need to be set but setting link configured afterwards makes the link
restoration work so we do that instead.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Do not change default USB4 router notification timeout

Some early stage USB4 devices do not like that any of the enumerating
router config space fields (ROUTER_CS_1 - ROUTER_CS_4) are written after
the initial enumeration for example when entering sleep states. The
default timeout by the USB4 spec is 10 ms which should be fine for the
driver to handle.

For this reason do not change the notification timeout from the default
10 ms for USB4 routers.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Initialize TMU again on resume

The TMU will be reset after router exits sleep so in order to
re-configure it upon resume make sure the structure is initialized again
based on the current hardware state.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Send reset only to first generation routers

First generation routers may need the reset command upon resume but it
is not supported by newer generations.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Do not program NFC buffers for USB4 router protocol adapters

USB4 spec says that NFC buffers field is not used for protocol adapters,
only for lane adapters so make tb_port_add_nfc_credits() skip non-lane
adapters in order to follow the spec.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Use kobj_to_dev() instead of container_of()

Doesn't really matter for an individual driver, but it may
get coppied to lots more. I consider it's a little tidy up.

Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Disable ports that are not implemented

Commit 4caf2511ec49 ("thunderbolt: Add trivial .shutdown") exposes a bug
in the Thunderbolt driver, that frees an unallocated id, resulting in the
following spinlock bad magic bug.

[ 20.633803] BUG: spinlock bad magic on CPU#4, halt/3313
[ 20.640030] lock: 0xffff92e6ad5c97e0, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[ 20.672139] Call Trace:
[ 20.675032] dump_stack+0x97/0xdb
[ 20.678950] ? spin_bug+0xa5/0xb0
[ 20.682865] do_raw_spin_lock+0x68/0x98
[ 20.687397] _raw_spin_lock_irqsave+0x3f/0x5d
[ 20.692535] ida_destroy+0x4f/0x124
[ 20.696657] tb_switch_release+0x6d/0xfd
[ 20.701295] device_release+0x2c/0x7d
[ 20.705622] kobject_put+0x8e/0xac
[ 20.709637] tb_stop+0x55/0x66
[ 20.713243] tb_domain_remove+0x36/0x62
[ 20.717774] nhi_remove+0x4d/0x58

Fix the issue by disabling ports that are enabled as per the EEPROM, but
not implemented. While at it, update the kernel doc for the disabled
field, to reflect this.

Cc: stable@vger.kernel.org
Fixes: 4caf2511ec49 ("thunderbolt: Add trivial .shutdown")
Reported-by: Srikanth Nandamuri <srikanth.nandamuri@intel.com>
Signed-off-by: Nikunj A. Dadhania <nikunj.dadhania@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

treewide: Use fallthrough pseudo-keyword

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>

thunderbolt: Add support for authenticate on disconnect

Some external devices can support completing thunderbolt authentication
when they are unplugged. For this to work though, the link controller must
remain operational.

The only device known to support this right now is the Dell WD19TB, so add
a quirk for this.

Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add support for separating the flush to SPI and authenticate

This allows userspace to have a shorter period of time that the device
is unusable and to call it at a more convenient time.

For example flushing the image may happen while the user is using the
machine and authenticating/rebooting may happen while logging out.

Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add support for on-board retimers

USB4 spec specifies standard access to retimers (both on-board and
cable) through USB4 port sideband access. This makes it possible to
upgrade their firmware in the same way than we already do with the
routers.

This enumerates on-board retimers under each USB4 port when the link
comes up and adds them to the bus under the router the retimer belongs
to. Retimers are exposed in sysfs with name like <device>:<port>.<index>
where device is the router the retimer belongs to, port is the USB4 port
the retimer is connected to and index is the retimer index under that
port (starting from 1). This applies to the upstream USB4 port as well
so if there is on-board retimer between the port and the router it is
also added accordingly.

At this time we do not add cable retimers but there is no techincal
restriction to do so in the future if needed. It is not clear whether it
makes sense to upgrade their firmwares and at least Thunderbolt 3 cables
it has not been done outside of lab environments.

The sysfs interface is made to follow the router NVM upgrade to make it
easy to extend the existing userspace (fwupd) to handle these as well.

Signed-off-by: Kranthi Kuntala <kranthi.kuntala@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Split common NVM functionality into a separate file

We are going to reuse some of this functionality to implement retimer
NVM upgrade so move common NVM functionality into its own file. We also
rename the structure from tb_switch_nvm to tb_nvm to make it clear that
it is not just for switches.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add Intel USB-IF ID to the NVM upgrade supported list

With USB4 Intel is also using its USB-IF ID (0x8087) with the new
devices. The NVM format is the same. Add this to the driver so NVM
upgrade is possible with these devices as well.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Make tb_port_get_link_speed() available to other files

We need to call this from tb.c when we improve the bandwidth management
to take USB3 into account.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Make tb_next_port_on_path() work with tree topologies

USB4 makes it possible to have tree topology of devices connected in the
same way than USB3. This was actually possible in Thunderbolt 1, 2 and 3
as well but all the available devices only had two ports which allows
building only daisy-chains of devices.

With USB4 it is possible for example that there is DP IN adapter as part
of eGPU device router and that should be tunneled over the tree topology
to a DP OUT adapter. This updates the tb_next_port_on_path() to support
such topologies.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: NHI can use HopIDs 1-7

NHI (The host interface adapter) is allowed to use HopIDs 1-7 as well so
relax the restriction in tb_port_alloc_hopid() to support this.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

PCI: Unify pcie_find_root_port() and pci_find_pcie_root_port()

Previously we used pcie_find_root_port() to find a Root Port from a PCIe
device and pci_find_pcie_root_port() to find a Root Port from a
Conventional PCI device.

Unify the two functions and use pcie_find_root_port() to find a Root Port
from either a Conventional PCI device or a PCIe device. Then there is no
need to distinguish the type of the device.

Link: https://lore.kernel.org/r/1589019568-5216-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # thunderbolt

Revert "thunderbolt: Prevent crash if non-active NVMem file is read"

This reverts commit 03cd45d2e219301880cabc357e3cf478a500080f.

Commit 664f0549380c ("nvmem: core: use is_bin_visible for permissions")
incidentally adds support for write-only nvmem. Hence, this workaround
is no longer required, so drop it.

Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Fix error code in tb_port_is_width_supported()

This function is type bool, and it's supposed to return true on success.
Unfortunately, this path takes negative error codes and casts them to
bool (true) so it's treated as success instead of failure.

Fixes: 91c0c12080d0 ("thunderbolt: Add support for lane bonding")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Prevent crash if non-active NVMem file is read

The driver does not populate .reg_read callback for the non-active NVMem
because the file is supposed to be write-only. However, it turns out
NVMem subsystem does not yet support this and expects that the .reg_read
callback is provided. If user reads the binary attribute it triggers
NULL pointer dereference like this one:

BUG: kernel NULL pointer dereference, address: 0000000000000000
...
Call Trace:
bin_attr_nvmem_read+0x64/0x80
kernfs_fop_read+0xa7/0x180
vfs_read+0xbd/0x170
ksys_read+0x5a/0xd0
do_syscall_64+0x43/0x150
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fix this in the driver by providing .reg_read callback that always
returns an error.

Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Fixes: e6b245ccd524 ("thunderbolt: Add support for host and device NVM firmware upgrade")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200213095604.1074-1-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: fix memory leak of object sw

In the case where the call tb_switch_exceeds_max_depth is true
the error reurn path leaks memory in sw. Fix this by setting
the return error code to -EADDRNOTAVAIL and returning via the
error exit path err_free_sw_ports to free sw. sw has been kzalloc'd
so the free of the NULL sw->ports is fine.

Addresses-Coverity: ("Resource leak")
Fixes: b04079837b20 ("thunderbolt: Add initial support for USB4")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191220220526.11307-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add support for USB 3.x tunnels

USB4 added a capability to tunnel USB 3.x protocol over the USB4
fabric. USB4 device routers may include integrated SuperSpeed HUB or a
function or both. USB tunneling follows PCIe so that the tunnel is
created between the parent and the child router from USB3 downstream
adapter port to USB3 upstream adapter port over a single USB4 link.

This adds support for USB 3.x tunneling and also capability to discover
existing USB 3.x tunnels (for example created by connection manager in
boot firmware).

Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-9-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add support for Time Management Unit

Time Management Unit (TMU) is included in each USB4 router. It is used
to synchronize time across the USB4 fabric. By default when USB4 router
is plugged to the domain, its TMU is turned off. This differs from
Thunderbolt (1, 2 and 3) devices whose TMU is by default configured to
bi-directional HiFi mode. Since time synchronization is needed for
proper Display Port tunneling this means we need to configure the TMU on
USB4 compliant devices.

The USB4 spec allows some flexibility on how the TMU can be configured.
This makes it possible to enable link power management states (CLx) in
certain topologies, where for example DP tunneling is not used. TMU can
also be re-configured dynamicaly depending on types of tunnels created
over the USB4 fabric.

In this patch we simply configure the TMU to be in bi-directional HiFi
mode. This way we can tunnel any kind of traffic without need to perform
complex steps to re-configure the domain dynamically. We can add more
fine-grained TMU configuration later on when we start enabling CLx
states.

Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-8-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add initial support for USB4

USB4 is the public specification based on Thunderbolt 3 protocol. There
are some differences in register layouts and flows. In addition to PCIe
and DP tunneling, USB4 supports tunneling of USB 3.x. USB4 is also
backward compatible with Thunderbolt 3 (and older generations but the
spec only talks about 3rd generation). USB4 compliant devices can be
identified by checking USB4 version field in router configuration space.

This patch adds initial support for USB4 compliant hosts and devices
which enables following features provided by the existing functionality
in the driver:

- PCIe tunneling
- Display Port tunneling
- Host and device NVM firmware upgrade
- P2P networking

This brings the USB4 support to the same level that we already have for
Thunderbolt 1, 2 and 3 devices.

Note the spec talks about host and device "routers" but in the driver we
still use term "switch" in most places. Both can be used interchangeably.

Co-developed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-5-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Make tb_find_port() available to other files

We will be needing this when adding initial USB4 support so make it
available to other files in the driver as well. We also rename it to
tb_switch_find_port() to follow conventions used in switch.c.

No functional changes.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-2-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Power cycle the router if NVM authentication fails

On zang's Dell XPS 13 9370 after Thunderbolt NVM firmware upgrade the
Thunderbolt controller did not come back as expected. Only after the
system was rebooted it became available again. It is not entirely clear
what happened but I suspect the new NVM firmware image authentication
failed for some reason. Regardless of this the router needs to be power
cycled if NVM authentication fails in order to get it fully functional
again.

This modifies the driver to issue a power cycle in case the NVM
authentication fails immediately when dma_port_flash_update_auth()
returns. We also need to call tb_switch_set_uuid() earlier to be able to
fetch possible NVM authentication failure when DMA port is added.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=205457
Reported-by: zang <dump@tzib.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add Display Port adapter pairing and resource management

To perform proper Display Port tunneling for Thunderbolt 3 devices we
need to allocate DP resources for DP IN port before they can be used.
The reason for this is that the user can also connect a monitor directly
to the Type-C ports in which case the Thunderbolt controller acts as
re-driver for Display Port (no tunneling takes place) taking the DP
sinks away from the connection manager. This allocation is done using
special sink allocation registers available through the link controller.

We can pair DP IN to DP OUT only if

* DP IN has sink allocated via link controller
* DP OUT port receives hotplug event

For DP IN adapters (only for the host router) we first query whether
there is DP resource available (it may be the previous instance of the
driver for example already allocated it) and if it is we add it to the
list. We then update the list when after each plug/unplug event to a DP
IN/OUT adapter. Each time the list is updated we try to find additional
DP IN <-> DP OUT pairs for tunnel establishment. This strategy also
makes it possible to establish another tunnel in case there are 3
monitors connected and one gets unplugged releasing the DP IN adapter
for the new tunnel.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add default linking between lane adapters if not provided by DROM

We currently read how sibling lane adapter ports relate each other from
DROM (Device ROM). If the two lane adapter ports go through the same
physical connector these lanes can then be bonded together. However,
some cases DROM does not provide this information or it is missing
completely (host routers typically do not have DROM). In this case we
have hard-coded the relationship.

Expand this to work with both legacy devices where lane adapter ports 1
and 2, and 3 and 4 are always linked together, and with USB4 devices
where lane adapter 1 is always following lane adapter 0 or is disabled
completely (see USB4 section 5.2.1 for more information).

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add support for lane bonding

Lane bonding allows aggregating two 10/20 Gb/s (depending on the
generation) lanes into a single 20/40 Gb/s bonded link. This allows
sharing the full bandwidth more efficiently. In order to establish lane
bonding we need to check that lane bonding is possible through link
controller and that both ends of the link actually supports 2x widths.
This also means that all the paths should be established through the
primary port so update tb_path_alloc() to handle this as well.

Lane bonding is supported starting from Falcon Ridge (2nd generation)
controllers.

We also expose the current speed and number of lanes under each device
except the host router following similar attribute naming than USB bus.
Expose speed and number of lanes for both directions to allow possibility
of asymmetric link in the future.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add helper macro to iterate over switch ports

There are quite many places in the driver where we iterate over each
port in the switch. To make it bit more convenient, add a macro that can
be used to iterate over each port and convert existing call sites to use it.

This is based on code by Lukas Wunner.

No functional changes.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Convert DP adapter register names to follow the USB4 spec

Now that USB4 spec has names for these DP adapter registers we can use
them instead. This makes it easier to match certain register to the spec.

No functional changes.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Convert PCIe adapter register names to follow the USB4 spec

Now that USB4 spec has names for these PCIe adapter registers we can use
them instead. This makes it easier to match certain register to the spec.

No functional changes.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Convert basic adapter register names to follow the USB4 spec

Now that USB4 spec has names for these basic registers we can use them
instead. This makes it easier to match certain register to the spec.

No functional changes.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Log error if adding switch fails

If we fail to add a switch for some reason log an error instead of
keeping silent. This is useful for debugging.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Introduce tb_switch_is_icm()

We currently differentiate between SW CM (Software Connection Manager,
sometimes also called External Connection Manager) and ICM (Firmware
based Connection Manager, Internal Connection Manager) by looking
directly at the sw->config.enabled field which may be rather hard to
understand for the casual reader. For this reason introduce a wrapper
function with documentation that should make the intention more clear.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add 'generation' attribute for devices

The Thunderbolt standard went through several major iterations, here
called generation. USB4, which will be based on Thunderbolt, will be
generation 4. Let userspace know the generation of the controller in
the devices in order to distinguish between Thunderbolt and USB4, so
it can be shown in various user interfaces.

Signed-off-by: Christian Kellner <christian@kellner.me>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Fix lockdep circular locking depedency warning

When lockdep is enabled, plugging Thunderbolt dock on Dominik's laptop
triggers following splat:

======================================================
WARNING: possible circular locking dependency detected
5.3.0-rc6+ #1 Tainted: G T
------------------------------------------------------
pool-/usr/lib/b/1258 is trying to acquire lock:
000000005ab0ad43 (pci_rescan_remove_lock){+.+.}, at: authorized_store+0xe8/0x210

but task is already holding lock:
00000000bfb796b5 (&tb->lock){+.+.}, at: authorized_store+0x7c/0x210

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&tb->lock){+.+.}:
__mutex_lock+0xac/0x9a0
tb_domain_add+0x2d/0x130
nhi_probe+0x1dd/0x330
pci_device_probe+0xd2/0x150
really_probe+0xee/0x280
driver_probe_device+0x50/0xc0
bus_for_each_drv+0x84/0xd0
__device_attach+0xe4/0x150
pci_bus_add_device+0x4e/0x70
pci_bus_add_devices+0x2e/0x66
pci_bus_add_devices+0x59/0x66
pci_bus_add_devices+0x59/0x66
enable_slot+0x344/0x450
acpiphp_check_bridge.part.0+0x119/0x150
acpiphp_hotplug_notify+0xaa/0x140
acpi_device_hotplug+0xa2/0x3f0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x234/0x580
worker_thread+0x50/0x3b0
kthread+0x10a/0x140
ret_from_fork+0x3a/0x50

-> #0 (pci_rescan_remove_lock){+.+.}:
__lock_acquire+0xe54/0x1ac0
lock_acquire+0xb8/0x1b0
__mutex_lock+0xac/0x9a0
authorized_store+0xe8/0x210
kernfs_fop_write+0x125/0x1b0
vfs_write+0xc2/0x1d0
ksys_write+0x6c/0xf0
do_syscall_64+0x50/0x180
entry_SYSCALL_64_after_hwframe+0x49/0xbe

other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&tb->lock);
lock(pci_rescan_remove_lock);
lock(&tb->lock);
lock(pci_rescan_remove_lock);

*** DEADLOCK ***
5 locks held by pool-/usr/lib/b/1258:
#0: 000000003df1a1ad (&f->f_pos_lock){+.+.}, at: __fdget_pos+0x4d/0x60
#1: 0000000095a40b02 (sb_writers#6){.+.+}, at: vfs_write+0x185/0x1d0
#2: 0000000017a7d714 (&of->mutex){+.+.}, at: kernfs_fop_write+0xf2/0x1b0
#3: 000000004f262981 (kn->count#208){.+.+}, at: kernfs_fop_write+0xfa/0x1b0
#4: 00000000bfb796b5 (&tb->lock){+.+.}, at: authorized_store+0x7c/0x210

stack backtrace:
CPU: 0 PID: 1258 Comm: pool-/usr/lib/b Tainted: G T 5.3.0-rc6+ #1

On an system using ACPI hotplug the host router gets hotplugged first and then
the firmware starts sending notifications about connected devices so the above
scenario should not happen in reality. However, after taking a second
look at commit a03e828915c0 ("thunderbolt: Serialize PCIe tunnel
creation with PCI rescan") that introduced the locking, I don't think it
is actually correct. It may have cured the symptom but probably the real
root cause was somewhere closer to PCI stack and possibly is already
fixed with recent kernels. I also tried to reproduce the original issue
with the commit reverted but could not.

So to keep lockdep happy and the code bit less complex drop calls to
pci_lock_rescan_remove()/pci_unlock_rescan_remove() in
tb_switch_set_authorized() effectively reverting a03e828915c0.

Link: https://lkml.org/lkml/2019/8/30/513
Fixes: a03e828915c0 ("thunderbolt: Serialize PCIe tunnel creation with PCI rescan")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Read DP IN adapter first two dwords in one go

When we discover existing DP tunnels the code checks whether DP IN
adapter port is enabled by calling tb_dp_port_is_enabled() before it
continues the discovery process. On Light Ridge (gen 1) controller
reading only the first dword of the DP IN config space causes subsequent
access to the same DP IN port path config space to fail or return
invalid data as can be seen in the below splat:

thunderbolt 0000:07:00.0: CFG_ERROR(0:d): Invalid config space or offset
Call Trace:
tb_cfg_read+0xb9/0xd0
__tb_path_deactivate_hop+0x98/0x210
tb_path_activate+0x228/0x7d0
tb_tunnel_restart+0x95/0x200
tb_handle_hotplug+0x30e/0x630
process_one_work+0x1b4/0x340
worker_thread+0x44/0x3d0
kthread+0xeb/0x120
? process_one_work+0x340/0x340
? kthread_park+0xa0/0xa0
ret_from_fork+0x1f/0x30

If both DP In adapter config dwords are read in one go the issue does
not reproduce. This is likely firmware bug but we can work it around by
always reading the two dwords in one go. There should be no harm for
other controllers either so can do it unconditionally.

Link: https://lkml.org/lkml/2019/8/28/160
Reported-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add support for Intel Ice Lake

The Thunderbolt controller is integrated into the Ice Lake CPU itself
and requires special flows to power it on and off using force power bit
in NHI VSEC registers. Runtime PM (RTD3) and Sx flows also differ from
the discrete solutions. Now the firmware notifies the driver whether
RTD3 entry or exit are possible. The driver is responsible of sending
Go2Sx command through link controller mailbox when system enters Sx
states (suspend-to-mem/disk). Rest of the ICM firwmare flows follow
Titan Ridge.

Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>

thunderbolt: Expose active parts of NVM even if upgrade is not supported

Ice Lake Thunderbolt controller NVM firmware is part of the BIOS image
which means it is not writable through the DMA port anymore. However, we
can still read it so we can keep nvm_version and active parts of NVM.
This way users still can find out the active NVM version and other
potentially useful information directly from Linux.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>

thunderbolt: Hide switch attributes that are not set

Thunderbolt host routers may not always contain DROM that includes
device identification information. This is mostly needed for Ice Lake
systems but some Falcon Ridge controllers on PCs also do not have DROM.

In that case hide the identification attributes.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>

thunderbolt: Do not fail adding switch if some port is not implemented

There are two ways to mark a port as unimplemented. Typical way is to
return port type as TB_TYPE_INACTIVE when its config space is read.
Alternatively if the port is not physically present (such as ports 10
and 11 in ICL) reading from port config space returns
TB_CFG_ERROR_INVALID_CONFIG_SPACE instead. Currently the driver bails
out from adding the switch if it receives any error during port
inititialization which is wrong.

Handle this properly and just leave the port as TB_TYPE_INACTIVE before
continuing to the next port.

This also allows us to get rid of special casing for Light Ridge port 5
in eeprom.c.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>

bus_find_device: Unify the match callback with class_find_device

There is an arbitrary difference between the prototypes of
bus_find_device() and class_find_device() preventing their callers
from passing the same pair of data and match() arguments to both of
them, which is the const qualifier used in the prototype of
class_find_device(). If that qualifier is also used in the
bus_find_device() prototype, it will be possible to pass the same
match() callback function to both bus_find_device() and
class_find_device(), which will allow some optimizations to be made in
order to avoid code duplication going forward. Also with that, constify
the "data" parameter as it is passed as a const to the match function.

For this reason, change the prototype of bus_find_device() to match
the prototype of class_find_device() and adjust its callers to use the
const qualifier in accordance with the new prototype of it.

Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Kershner <david.kershner@unisys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: rafael@kernel.org
Acked-by: Corey Minyard <minyard@acm.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Make sure device runtime resume completes before taking domain lock

When a device is authorized from userspace by writing to authorized
attribute we first take the domain lock and then runtime resume the
device in question. There are two issues with this.

First is that the device connected notifications are blocked during this
time which means we get them only after the authorization operation is
complete. Because of this the authorization needed flag from the
firmware notification is not reflecting the real authorization status
anymore. So what happens is that the "authorized" keeps returning 0 even
if the device was already authorized properly.

Second issue is that each time the controller is runtime resumed the
connection_id field of device connected notification may be different
than in the previous resume. We need to use the latest connection_id
otherwise the firmware rejects the authorization command.

Fix these by moving runtime resume operations to happen before the
domain lock is taken, and waiting for the updated device connected
notification from the firmware before we allow runtime resume of a
device to complete.

While there add missing locking to tb_switch_nvm_read().

Fixes: 09f11b6c99fe ("thunderbolt: Take domain lock in switch sysfs attribute callbacks")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Make rest of the logging to happen at debug level

Now that the driver can handle every possible tunnel types there is no
point to log everything as info level so turn these to happen at debug
level instead.

While at it remove duplicated tunnel activation log message
(tb_tunnel_activate() calls tb_tunnel_restart() which print the same
message) and add one missing '\n' termination.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add support for XDomain connections

Two domains (hosts) can be connected through a Thunderbolt cable and in
that case they can start software services such as networking over the
high-speed DMA paths. Now that we have all the basic building blocks in
place to create DMA tunnels over the Thunderbolt fabric we can add this
support to the software connection manager as well.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Make tb_switch_alloc() return ERR_PTR()

In order to detect possible connections to other domains we need to be
able to find out why tb_switch_alloc() fails so make it return ERR_PTR()
instead. This allows the caller to differentiate between errors such as
-ENOMEM which comes from the kernel and for instance -EIO which comes
from the hardware when trying to access the possible switch.

Convert all the current call sites to handle this properly.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add support for DMA tunnels

In addition to PCIe and Display Port tunnels it is also possible to
create tunnels that forward DMA traffic from the host interface adapter
(NHI) to a NULL port that is connected to another domain through a
Thunderbolt cable. These tunnels can be used to carry software messages
such as networking packets.

To support this we introduce another tunnel type (TB_TUNNEL_DMA) that
supports paths from NHI to NULL port and back.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add support for Display Port tunnels

Display Port tunnels are somewhat more complex than PCIe tunnels as it
requires 3 tunnels (AUX Rx/Tx and Video). In addition we are not
supposed to create the tunnels immediately when a DP OUT is enumerated.
Instead we need to wait until we get hotplug event to that adapter port
or check if the port has HPD set before tunnels can be established. This
adds Display Port tunneling support to the software connection manager.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Rework NFC credits handling

NFC (non flow control) credits is actually 20-bit field so update
tb_port_add_nfc_credits() to handle this properly. This allows us to set
NFC credits for Display Port path in subsequent patches.

Also make sure the function does not update the hardware if the
underlying switch is already unplugged.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Generalize port finding routines to support all port types

We will be needing these routines to find Display Port adapters as well
so modify them to take port type as the second parameter.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Discover preboot PCIe paths the boot firmware established

In Apple Macs the boot firmware (EFI) connects all devices automatically
when the system is started, before it hands over to the OS. Instead of
ignoring we discover all those PCIe tunnels and record them using our
internal structures, just like we do when a device is connected after
the OS is already up.

By doing this we can properly tear down tunnels when devices are
disconnected. Also this allows us to resume the existing tunnels after
system suspend/resume cycle.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add helper function to iterate from one port to another

We need to be able to walk from one port to another when we are creating
paths where there are multiple switches between two ports. For this
reason introduce a new function tb_next_port_on_path().

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>

thunderbolt: Assign remote for both ports in case of dual link

Currently the driver only assigns remote port for the primary port if in
case of dual link. This makes things such as walking from one port to
another more complex than necessary because the code needs to change
from secondary to primary port if the path that is established is
created using secondary links.

In order to always assign both remote pointers we need to prevent the
scanning code from following the secondary link. Failing to do that
might cause problems as the same switch may be enumerated twice (or
removed in case of unplug). Handle that properly by introducing a new
function tb_port_has_remote() that returns true only for the primary
port. We also update tb_is_upstream_port() to support both dual link
ports, make it take const port pointer and move it below
tb_upstream_port() to keep similar functions close.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Add functions for allocating and releasing HopIDs

Each port has a separate path configuration space that is used for
finding the next hop (switch) in the path. HopID is an index to this
configuration space. HopIDs 0 - 7 are reserved by the protocol.

In order to get next available HopID for each direction we provide two
pairs of helper functions that can be used to allocate and release
HopIDs for a given port.

While there remove obsolete TODO comment.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Generalize tunnel creation functionality

To be able to tunnel non-PCIe traffic, separate tunnel functionality
into generic and PCIe specific parts. Rename struct tb_pci_tunnel to
tb_tunnel, and make it hold an array of paths instead of just two.
Update all the tunneling functions to take this structure as parameter.

We also move tb_pci_port_active() to switch.c (and rename it) where we
will be keeping all port and switch related functions.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Cache adapter specific capability offset into struct port

The adapter specific capability either is there or not if the port does
not hold an adapter. Instead of always finding it on-demand we read the
offset just once when the port is initialized.

While there we update the struct port documentation to follow kernel-doc
format.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Set sleep bit when suspending switch

Thunderbolt 2 devices and beyond link controller needs to be notified
when a switch is going to be suspended by setting bit 31 in LC_SX_CTRL
register. Add this functionality to the software connection manager.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Configure lanes when switch is initialized

Thunderbolt 2 devices and beyond need to have additional bits set in
link controller specific registers. This includes two bits in LC_SX_CTRL
that tell the link controller which lane is connected and whether it is
upstream facing or not.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Move LC specific functionality into a separate file

We will be adding more link controller functionality in subsequent
patches and it does not make sense to keep all that in switch.c, so
separate LC functionality into its own file.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Do not allocate switch if depth is greater than 6

Maximum depth in Thunderbolt topology is 6 so make sure it is not
possible to allocate switches that exceed the depth limit.

While at it update tb_switch_alloc() to use upper/lower_32_bits()
following tb_switch_alloc_safe_mode().

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Take domain lock in switch sysfs attribute callbacks

switch_lock was introduced because it allowed serialization of device
authorization requests from userspace without need to take the big
domain lock (tb->lock). This was fine because device authorization with
ICM is just one command that is sent to the firmware. Now that we start
to handle all tunneling in the driver switch_lock is not enough because
we need to walk over the topology to establish paths.

For this reason drop switch_lock from the driver completely in favour of
big domain lock.

There is one complication, though. If userspace is waiting for the lock
in tb_switch_set_authorized(), it keeps the device_del() from removing
the sysfs attribute because it waits for active users to release the
attribute first which leads into following splat:

INFO: task kworker/u8:3:73 blocked for more than 61 seconds.
Tainted: G W 5.1.0-rc1+ #244
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u8:3 D12976 73 2 0x80000000
Workqueue: thunderbolt0 tb_handle_hotplug [thunderbolt]
Call Trace:
? __schedule+0x2e5/0x740
? _raw_spin_lock_irqsave+0x12/0x40
? prepare_to_wait_event+0xc5/0x160
schedule+0x2d/0x80
__kernfs_remove.part.17+0x183/0x1f0
? finish_wait+0x80/0x80
kernfs_remove_by_name_ns+0x4a/0x90
remove_files.isra.1+0x2b/0x60
sysfs_remove_group+0x38/0x80
sysfs_remove_groups+0x24/0x40
device_remove_attrs+0x3d/0x70
device_del+0x14c/0x360
device_unregister+0x15/0x50
tb_switch_remove+0x9e/0x1d0 [thunderbolt]
tb_handle_hotplug+0x119/0x5a0 [thunderbolt]
? process_one_work+0x1b7/0x420
process_one_work+0x1b7/0x420
worker_thread+0x37/0x380
? _raw_spin_unlock_irqrestore+0xf/0x30
? process_one_work+0x420/0x420
kthread+0x118/0x130
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x35/0x40

We deal this by following what network stack did for some of their
attributes and use mutex_trylock() with restart_syscall(). This makes
userspace release the attribute allowing sysfs attribute removal to
progress before the write is restarted and eventually fail when the
attribute is removed.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Drop duplicated get_switch_at_route()

tb_switch_find_by_route() does the same already so use it instead and
remove duplicated get_switch_at_route().

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>

thunderbolt: Fix to check for kmemdup failure

Memory allocated via kmemdup might fail and return a NULL pointer.
This patch adds a check on the return value of kmemdup and passes the
error upstream.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Prevent root port runtime suspend during NVM upgrade

During NVM upgrade process the host router is hot-removed for a short
while. During this time it is possible that the root port is moved into
D3cold which would be fine if the root port could trigger PME on itself.
However, many systems actually do not implement it so what happens is
that the root port goes into D3cold and never wakes up unless userspace
does PCI config space access, such as running 'lscpi'.

For this reason we explicitly prevent the root port from runtime
suspending during NVM upgrade.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add Intel as copyright holder

Intel has done pretty major changes to the driver and we continue to do
so in the future as well. Add Intel as copyright holder of the files we
have done changes.

While there drop "Cactus Ridge" from the headers because this driver
works also with other Thunderbolt controllers.

No functional changes intended.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Print connected devices

The previous patch made the driver less verbose meanining that all the
switch structures and ports are now logged as debug level. However, we
have been missing similar output that USB for intance prints when a new
USB device is connected and disconnected. This information is useful for
end users as well as developers because it immediately shows the actual
device that was connected.

This patch adds printing of the actual connected devices to the driver.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Make the driver less verbose

Currently the driver logs quite a lot to the system message buffer even
when doing normal operations. This information is not useful for
ordinary users and might even annoy some.

For this reason convert most of the logs at info level to happen at
debug level instead. The nice output formatting is untouched.

Logging can be easily re-enabled by passing "thunderbolt.dyndbg" in the
kernel command line (or using the corresponding control file runtime).

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add support for runtime PM

When Thunderbolt host controller is set to RTD3 mode (Runtime D3) it is
present all the time. Because of this it is important to runtime suspend
the controller whenever possible. In case of ICM we have following rules
which all needs to be true before the host controller can be put to D3:

- The controller firmware reports to support RTD3
- All the connected devices announce support for RTD3
- There is no active XDomain connection

Implement this using standard Linux runtime PM APIs so that when all the
children devices are runtime suspended, the Thunderbolt host controller
PCI device is runtime suspended as well. The ICM firmware then starts
powering down power domains towards RTD3 but it can prevent this if it
detects that there is an active Display Port stream (this is not visible
to the software, though).

The Thunderbolt host controller will be runtime resumed either when
there is a remote wake event (device is connected or disconnected), or
when there is access from userspace that requires hardware access.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add support for Intel Titan Ridge

Intel Titan Ridge is the next Thunderbolt 3 controller. The ICM firmware
message format in Titan Ridge differs from Falcon Ridge and Alpine Ridge
somewhat because it is using route strings addressing devices. In
addition to that the DMA port of 4-channel (two port) controller is in
different port number than the previous controllers. There are some
other minor differences as well.

This patch add support for Intel Titan Ridge and the new ICM firmware
message format.

Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

thunderbolt: Add 'boot' attribute for devices

In various cases, Thunderbolt device can be connected by ICM on boot
without waiting for approval from user. Most cases are related to
OEM-specific BIOS configurations. This information is interesting for
user-space as if the device isn't in SW ACL, it may create a friction in
the user experience where the device is automatically authorized if it's
connected on boot but requires an explicit user action if connected
after OS is up. User-space can use this information to suggest adding
the device to SW ACL for auto-authorization on later connections.

Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

thunderbolt: Add tb_switch_find_by_route()

With the new ICM messaging there is need for find switch by route string
instead of link and depth. Add new function that makes it possible.

Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

thunderbolt: Correct function name in kernel-doc comment

Use correct name in kernel-doc of tb_switch_find_by_uuid().

Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

thunderbolt: Serialize PCIe tunnel creation with PCI rescan

We need to make sure a new PCIe tunnel is not created in a middle of
previous PCI rescan because otherwise the rescan code might find too
much and fail to reconfigure devices properly. This is important when
native PCIe hotplug is used. In BIOS assisted hotplug there should be no
such issue.

Fixes: f67cf491175a ("thunderbolt: Add support for Internal Connection Manager (ICM)")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add support for XDomain discovery protocol

When two hosts are connected over a Thunderbolt cable, there is a
protocol they can use to communicate capabilities supported by the host.
The discovery protocol uses automatically configured control channel
(ring 0) and is build on top of request/response transactions using
special XDomain primitives provided by the Thunderbolt base protocol.

The capabilities consists of a root directory block of basic properties
used for identification of the host, and then there can be zero or more
directories each describing a Thunderbolt service and its capabilities.

Once both sides have discovered what is supported the two hosts can
setup high-speed DMA paths and transfer data to the other side using
whatever protocol was agreed based on the properties. The software
protocol used to communicate which DMA paths to enable is service
specific.

This patch adds support for the XDomain discovery protocol to the
Thunderbolt bus. We model each remote host connection as a Linux XDomain
device. For each Thunderbolt service found supported on the XDomain
device, we create Linux Thunderbolt service device which Thunderbolt
service drivers can then bind to based on the protocol identification
information retrieved from the property directory describing the
service.

This code is based on the work done by Amir Levy and Michael Jamet.

Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

thunderbolt: Allow clearing the key

If secure authentication of a devices fails, either because the device
already has another key uploaded, or there is some other error sending
challenge to the device, and the user only wants to approve the device
just once (without a new key being uploaded to the device) the current
implementation does not allow this because the key cannot be cleared
once set even if we allow it to be changed.

Make this scenario possible and allow clearing the key by writing
empty string to the key sysfs file.

Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Make key root-only accessible

Non-root user may read the key back after root wrote it there.
This removes read access to everyone but root.

Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Remove superfluous check

The key size is tested by hex2bin() already (as '\0' isn't an hex digit)

Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: use uuid_t instead of uuid_be

Switch thunderbolt to the new uuid type.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

thunderbolt: Correct access permissions for active NVM contents

Firmware upgrade tools that decide which NVM image should be uploaded to
the Thunderbolt controller need to access active parts of the NVM even
if they are not run as root. The information in active NVM is not
considered security critical so we can use the default permissions set
by the NVMem framework.

Writing the NVM image is still left as root only operation.

While there mark the active NVM as read-only in the filesystem.

Reported-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add support for host and device NVM firmware upgrade

Starting from Intel Falcon Ridge the NVM firmware can be upgraded by
using DMA configuration based mailbox commands. If we detect that the
host or device (device support starts from Intel Alpine Ridge) has the
DMA configuration based mailbox we expose NVM information to the
userspace as two separate Linux NVMem devices: nvm_active and
nvm_non_active. The former is read-only portion of the active NVM which
firmware upgrade tools can be use to find out suitable NVM image if the
device identification strings are not enough.

The latter is write-only portion where the new NVM image is to be
written by the userspace. It is up to the userspace to find out right
NVM image (the kernel does very minimal validation). The ICM firmware
itself authenticates the new NVM firmware and fails the operation if it
is not what is expected.

We also expose two new sysfs files per each switch: nvm_version and
nvm_authenticate which can be used to read the active NVM version and
start the upgrade process.

We also introduce safe mode which is the mode a switch goes when it does
not have properly authenticated firmware. In this mode the switch only
accepts a couple of commands including flashing a new NVM firmware image
and triggering power cycle.

This code is based on the work done by Amir Levy and Michael Jamet.

Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add support for Internal Connection Manager (ICM)

Starting from Intel Falcon Ridge the internal connection manager running
on the Thunderbolt host controller has been supporting 4 security
levels. One reason for this is to prevent DMA attacks and only allow
connecting devices the user trusts.

The internal connection manager (ICM) is the preferred way of connecting
Thunderbolt devices over software only implementation typically used on
Macs. The driver communicates with ICM using special Thunderbolt ring 0
(control channel) messages. In order to handle these messages we add
support for the ICM messages to the control channel.

The security levels are as follows:

none - No security, all tunnels are created automatically
user - User needs to approve the device before tunnels are created
secure - User need to approve the device before tunnels are created.
The device is sent a challenge on future connects to be able
to verify it is actually the approved device.
dponly - Only Display Port and USB tunnels can be created and those
are created automatically.

The security levels are typically configurable from the system BIOS and
by default it is set to "user" on many systems.

In this patch each Thunderbolt device will have either one or two new
sysfs attributes: authorized and key. The latter appears for devices
that support secure connect.

In order to identify the device the user can read identication
information, including UUID and name of the device from sysfs and based
on that make a decision to authorize the device. The device is
authorized by simply writing 1 to the "authorized" sysfs attribute. This
is following the USB bus device authorization mechanism. The secure
connect requires an additional challenge step (writing 2 to the
"authorized" attribute) in future connects when the key has already been
stored to the NVM of the device.

Non-ICM systems (before Alpine Ridge) continue to use the existing
functionality and the security level is set to none. For systems with
Alpine Ridge, even on Apple hardware, we will use ICM.

This code is based on the work done by Amir Levy and Michael Jamet.

Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add support for DMA configuration based mailbox

The DMA (NHI) port of a switch provides access to the NVM of the host
controller (and devices starting from Intel Alpine Ridge). The NVM
contains also more complete DROM for the root switch including vendor
and device identification strings.

This will look for the DMA port capability for each switch and if found
populates sw->dma_port. We then teach tb_drom_read() to read the DROM
information from NVM if available for the root switch.

The DMA port capability also supports upgrading the NVM for both host
controller and devices which will be added in subsequent patches.

This code is based on the work done by Amir Levy and Michael Jamet.

Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Store Thunderbolt generation in the switch structure

In some cases it is useful to know what is the Thunderbolt generation
the switch supports. This introduces a new field to struct switch that
stores the generation of the switch based on the device ID. Unknown
switches (there should be none) are assumed to be first generation to be
on the safe side.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add new Thunderbolt PCI IDs

Add Intel Win Ridge (Thunderbolt 2) and Alpine Ridge (Thunderbolt 3)
controller PCI IDs to the list of supported devices.

This code is based on the work done by Amir Levy and Michael Jamet.

Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Read vendor and device name from DROM

The device DROM contains name of the vendor and device among other
things. Extract this information and expose it to the userspace via two
new attributes.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Fail switch adding operation if reading DROM fails

All non-root switches are expected to have DROM so if the operation
fails, it might be due the user unlugging the device. There is no point
continuing adding the switch further in that case. Just bail out.

For root switches (hosts) the DROM is either retrieved from a EFI
variable, NVM or hard-coded.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Convert switch to a device

Thunderbolt domain consists of switches that are connected to each
other, forming a bus. This will convert each switch into a real Linux
device structure and adds them to the domain. The advantage here is
that we get all the goodies from the driver core, like reference
counting and sysfs hierarchy for free.

Also expose device identification information to the userspace via new
sysfs attributes.

In order to support internal connection manager (ICM) we separate switch
configuration into its own function (tb_switch_configure()) which is
only called by the existing native connection manager implementation
used on Macs.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Rework capability handling

Organization of the capabilities in switches and ports is not so random
after all. Rework the capability handling functionality so that it
follows how capabilities are organized and provide two new functions
(tb_switch_find_vse_cap() and tb_port_find_cap()) which can be used to
extract capabilities for ports and switches. Then convert the current
users over these.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: No need to read UID of the root switch on resume

The root switch is part of the host controller and cannot be physically
removed, so there is no point of reading UID again on resume in order to
check if the root switch is still the same.

Suggested-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Use Device ROM retrieved from EFI

Macs with Thunderbolt 1 do not have a unit-specific DROM: The DROM is
empty with uid 0x1000000000000. (Apple started factory-burning a unit-
specific DROM with Thunderbolt 2.)

Instead, the NHI EFI driver supplies a DROM in a device property. Use
it if available. It's only available when booting with the efistub.
If it's not available, silently fall back to our hardcoded DROM.

The size of the DROM is always 256 bytes. The number is hardcoded into
the NHI EFI driver. This commit can deal with an arbitrary size however,
just in case they ever change that.

Background information: The EFI firmware volume contains ROM files for
the NHI, GMUX and several other chips as well as key material. This
strategy allows Apple to deploy ROM or key updates by simply publishing
an EFI firmware update on their website. Drivers do not access those
files directly but rather through a file server via EFI protocol
AC5E4829-A8FD-440B-AF33-9FFE013B12D8. Files are identified by GUID, the
NHI DROM has 339370BD-CFC6-4454-8EF7-704653120818.

The NHI EFI driver amends that file with a unit-specific uid. The uid
has 64 bit but its entropy is much lower: 24 bit represent the model,
24 bit are taken from a serial number, 16 bit are fixed. The NHI EFI
driver obtains the serial number via the DataHub protocol, copies it
into the DROM, calculates the CRC and submits the result as a device
property.

A modification is needed in the resume code where we currently read the
uid of all switches in the hierarchy to detect plug events that occurred
during sleep. On Thunderbolt 1 root switches this will now lead to a
mismatch between the uid of the empty DROM and the EFI DROM. Exempt the
root switch from this check: It's built in, so the uid should never
change. However we continue to *read* the uid of the root switch, this
seems like a good way to test its reachability after resume.

Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: Pierre Moreau <pierre.morrow@free.fr> [MacBookPro11,3]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pedro Vilaça <reverser@put.as>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-10-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>

thunderbolt: Don't declare Falcon Ridge unsupported

Falcon Ridge 4C has been supported by the driver from the beginning,
Falcon Ridge 2C support was just added. Don't irritate users with a
warning declaring the opposite.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Support 1st gen Light Ridge controller

Add support for the 1st gen Light Ridge controller, which is built into
these systems:

iMac12,1 2011 21.5"
iMac12,2 2011 27"
Macmini5,1 2011 i5 2.3 GHz
Macmini5,2 2011 i5 2.5 GHz
Macmini5,3 2011 i7 2.0 GHz
MacBookPro8,1 2011 13"
MacBookPro8,2 2011 15"
MacBookPro8,3 2011 17"
MacBookPro9,1 2012 15"
MacBookPro9,2 2012 13"

Light Ridge (CV82524) was the very first copper Thunderbolt controller,
introduced 2010 alongside its fiber-optic cousin Light Peak (CVL2510).
Consequently the chip suffers from some teething troubles:

- MSI is broken for hotplug signaling on the downstream bridges: The chip
just never sends an interrupt. It requests 32 MSIs for each of its six
bridges and the pcieport driver only allocates one per bridge. However
I've verified that even if 32 MSIs are allocated there's no interrupt
on hotplug. The only option is thus to disable MSI, which is also what
OS X does. Apparently all Thunderbolt chips up to revision 1 of Cactus
Ridge 4C are plagued by this issue so quirk those as well.

- The chip supports a maximum hop_count of 32, unlike its successors
which support only 12. Fixup ring_interrupt_active() to cope with
values >= 32.

- Another peculiarity is that the chip supports a maximum of 13 ports
whereas its successors support 12. However the additional port (#5)
seems to be unusable as reading its TB_CFG_PORT config space results in
TB_CFG_ERROR_INVALID_CONFIG_SPACE. Add a quirk to mark the port
disabled on the root switch, assuming that's necessary on all Macs
using this chip.

Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: William Brown <william@blackhats.net.au> [MacBookPro8,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>

thunderbolt: Fix typos and magic number

Fix typo in tb_cfg_print_error() message. Fix bytecount in struct
tb_drom_entry_port comment. Replace magic number in tb_switch_alloc().
Rename tb_sw_set_unpplugged() and TB_CAL_IECS to fix typos.

[bhelgaas: no functional change intended]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>

PCI: Add Intel Thunderbolt device IDs

Intel Gen 1 and 2 chips use the same ID for NHI, bridges and switch. Gen 3
chips and onward use a distinct ID for the NHI.

No functional change intended.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>

thunderbolt: Use NULL instead of 0 in switch.c

The function returns a pointer. Hence return NULL instead of 0.

Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Fix build error in switch.c

Fixes the below error:
drivers/thunderbolt/switch.c:347:2: error: implicit declaration of function ‘kzalloc’ [-Werror=implicit-function-declaration]
drivers/thunderbolt/switch.c:381:2: error: implicit declaration of function ‘kcalloc’ [-Werror=implicit-function-declaration]

Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Fix nontrivial endpoint devices.

Fix issues observed with the Startech docking station:

Fix the type of the route parameter in tb_ctl_rx. It should be u64 and not
u8 (which only worked for short routes).

A thunderbolt cable contains two lanes. If both endpoints support it a
connection will be established on both lanes. Previously we tried to
scan below both "dual link ports". Use the information extracted from
the drom to only scan behind ports with lane_nr == 0.

Endpoints with more complex thunderbolt controllers have some of their
ports disabled (for example the NHI port or one of the HDMI/DP ports).
Accessing them results in an error so we now ignore ports which are
marked as disabled in the drom.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Read port configuration from eeprom.

All Thunderbolt switches (except the root switch) contain a drom which
contains information about the device. Right now we only read the UID.

Add code to read and parse this drom. For now we are only interested in
which ports are disabled and which ports are "dual link ports" (a
physical thunderbolt port/socket contains two such ports).

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add suspend/hibernate support

We use _noirq since we have to restore the pci tunnels before the pci
core wakes the tunneled devices.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Read switch uid from EEPROM

Add eeprom access code and read the uid during switch initialization.
The UID will be used to check device identity after suspend.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Add path setup code.

A thunderbolt path is a unidirectional channel between two thunderbolt
ports. Two such paths are needed to establish a pci tunnel.

This patch introduces struct tb_path as well as a set of tb_path_*
methods which are used to activate & deactivate paths.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Handle hotplug events

We receive a plug event callback whenever a thunderbolt device is added
or removed. This patch fills in the tb_handle_hotplug method and starts
reacting to these events by adding/removing switches from the hierarchy.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Scan for downstream switches

Add utility methods tb_port_state and tb_wait_for_port. Add
tb_scan_switch which recursively checks for downstream switches.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Enable plug events

Thunderbolt switches have a plug events capability. This patch adds the
tb_plug_events_active method and uses it to activate plug events during
switch allocation.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Initialize root switch and ports

This patch adds the structures tb_switch and tb_port as well as code to
initialize the root switch.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>