wifi: rt2x00: introduce DMA busy check watchdog for rt2800

When I tried to fix the watchdog of rt2800, I found that sometimes
the watchdog can not reset the hung device. This is because the
queue is not completely stuck, it just becomes very slow. The MTK
vendor driver for the new chip MT7603/MT7612 has a DMA busy watchdog
to detect device hangs by checking DMA busy status. This watchdog
implementation is something similar to it. To reduce unnecessary
reset, we can check the INT_SOURCE_CSR register together as I found
that when the radio hung, the RX/TX coherent interrupt will always
stuck at triggered state.

The 'watchdog' module parameter has been extended to control all
watchdogs(0=disabled, 1=hang watchdog, 2=DMA watchdog, 3=both). This
new watchdog function is a slight schedule and it won't affect the
transmission speed. So we can turn on it by default. Due to the
INT_SOURCE_CSR register is invalid on rt2800 USB NICs, the DMA busy
watchdog will be automatically disabled for them.

Tested on MT7620 and RT5350.

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB0315D7462CE08A119A99DE34BCA4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM

wifi: rt2x00: improve MT7620 register initialization

1. Do not hard reset the BBP. We can use soft reset instead. This
change has some help to the calibration failure issue.
2. Enable falling back to legacy rate from the HT/RTS rate by
setting the HT_FBK_TO_LEGACY register.
3. Implement MCS rate specific maximum PSDU size. It can improve
the transmission quality under the low RSSI condition.
4. Set BBP_84 register value to 0x19. This is used for extension
channel overlapping IOT.

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB031553CCD4B7A3B89C85935DBCD4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM

wifi: rt2x00: add r calibration for MT7620

Add r calibration code as found in mtk driver.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/e0c34f233089bec4eb73826bc4f512166ee25934.1663445157.git.daniel@makrotopia.org

wifi: rt2x00: add support for external PA on MT7620

Implement support for external PA connected to MT7620A.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
[pozega.tomislav@gmail.com: use chanreg and dccal helpers.]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/af2c68ff831816a86fc39b0c10911c129a1f03dc.1663445157.git.daniel@makrotopia.org

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13

Based on 2 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 355 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rt2x00: add RT3883 support

Patch add support for RT3883 chip. Code was taken direclty
from openwrt project and merge into one patch.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: fix spelling mistake in various macros, UKNOWN -> UNKNOWN

Rename several macros that contain mispellings of UNKNOWN

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: rt2800: add antenna diversity for RT5370G

RT5370G has hardware RX antenna diversity like RT5390R.
Based on DPO_RT5572_LinuxSTA_2.6.1.3_20121022.tar.bz2 manufacturer driver:
https://d86o2zu8ugzlg.cloudfront.net/mediatek-craft/drivers/DPO_RT5572_LinuxSTA_2.6.1.3_20121022.tar.bz2

Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: wireless newbie <wnewbie72@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux wireless ml <linux-wireless@vger.kernel.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: add support for MT7620

Basic support for MT7620 built-in wireless radio was added to
OpenWrt in r41441. It has seen some heavy cleaning and refactoring
since in order to match the Kernel's code quality standards.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: fix TX_PWR_CFG_4 register definition

Some of the macros used to describe the TX_PWR_CFG_4 register accidentally
refer to TX_PWR_CFG_3, probably a copy&paste error. Fix that.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2800: status based rate flags for nomatch case

We use skb_desc->tx_rate_flags from entry as rate[].flags even if
skb does not match status. Patch corrects flags and also fixes
mcs for legacy rates.

rt2800_rate_from_status() is based on Felix's mt76
mt76x2_mac_process_tx_rate() function.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: rt2800lib: move rt2800_drv_data declaration into rt2800lib.h

The rt2800_drv_data structure contains driver specific
information. Move the declaration into the rt2800lib.h
header which is a more logical place for it. Also fix
the comment style to avoid checkpatch warning.

The patch contains no functional changes, it is in
preparation for the next patch.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: add support for RT5350 WiSoC

Support for the RT5350 WiSoC was added to OpenWrt after having a
lengthy debate about the legality of the original submission, see
https://lists.openwrt.org/pipermail/openwrt-devel/2013-January/018224.html
MTK/Ralink Acked replied and says we can merge this patch under the GPL.
https://dev.openwrt.org/changeset/36177

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Tested-by: Michel Stempin <michel.stempin@wanadoo.fr>
Acked-by: John Crispin <blogic@openwrt.org>
[daniel@makrotopia.org: added commit message, cleaned up code]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: rt2800lib: support for for RT3352 with external PA

This is needed for WiFi to work e.g. on DIR-615 rev.H1 which got
external RF power amplifiers connected to the WiSoC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: rt2800lib: correctly set HT20/HT40 filter

Simple patch to correct HT20/HT40 filter setting.
Tested with Rt3290, Rt3352 and Rt5350

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2800: set MAX_PSDU len according to remote STAs capabilities

MAX_LEN_CFG_MAX_PSDU specify maximum transmitted by HW AMPDU length
(0 - 8kB, 1 - 16kB, 2 - 32kB, 3 - 64kB). Set this option according to
remote stations capabilities (based on HT ampdu_factor). However limit
the value based our hardware TX capabilities as some chips can not send
more than 16kB (factor 1). Limit for all chips is currently 32kB
(factor 2), but perhaps for some chips this could be increased
to 64kB by setting drv_data->max_psdu to 3.

Since MAX_LEN_CFG_MAX_PSDU is global setting, on multi stations modes
(AP, IBSS, mesh) we limit according to less capable remote STA. We can
not set bigger value to speed up communication with some stations and
do not break communication with slow stations.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: move under ralink vendor directory

Part of reorganising wireless drivers directory and Kconfig.

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>