drm/amd/display: fix disable otg wa logic in DCN316

[Why]
Wrong logic cause screen corruption.

[How]
Port logic from DCN35/314.

Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Fudongwang <fudong.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Wake DMCUB before sending a command

[Why]
We can hang in place trying to send commands when the DMCUB isn't
powered on.

[How]
For functions that execute within a DC context or DC lock we can
wrap the direct calls to dm_execute_dmub_cmd/list with code that
exits idle power optimizations and reallows once we're done with
the command submission on success.

For DM direct submissions the DM will need to manage the enter/exit
sequencing manually.

We cannot invoke a DMCUB command directly within the DM execution
helper or we can deadlock.

Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Clean up errors in dcn316_clk_mgr.c

Fix the following errors reported by checkpatch:

ERROR: open brace '{' following struct go on the same line

Signed-off-by: Ran Sun <sunran001@208suo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Hardcode vco_freq for dcn316

There is no need to calculate the VCO frequency. In our internal branch
we've hard-coded this for a while, so it's well-tested. This also allows
us to remove the now unused code for calculating the VCO frequency.

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Alan Liu <haoping.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Clean FPGA code in dc

[Why]
Drop dead code for Linux.

[How]
Remove all IS_FPGA_MAXIMUS_DC and IS_DIAG_DC

Reviewed-by: Ariel Bernstein <eric.bernstein@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: refactor dmub commands into single function

[Why & How]
Consolidate dmub access to a single interface. This makes it easier to
add code in the future that needs to run every time a dmub command is
requested (e.g. instrumentation, locking etc).

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: merge dc_link_dp into dc_link

[why]
Temporarly merge dc_link_dp functions into dc_link for the
purpose of removing dc_link_dp files. This is a transitional
change for later commits where we will further refactor dc_link
file.

Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix dcn3.1x mode validation on high bandwidth config

[why]
1. correct dram_channel_width (was hard coded to 4 for 32bit)
2. use dm's is_hvm_enable status flag for hostvm_en input for dml.
3. add a function to override to all dcn3.1x.

Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Display distortion after hotplug 5K tiled display

[Why]
During hot plug of specific 5K tiled display, sometimes both the tiles
are not synchronized resulting in distortion. The reason is that otgs of
both the tiles goes out of sync when otg workaround (dcnxxx_disable_otg_wa)
is applied for bandwidth optimization. The otg workaround reenables otg
but otg synchronization context is not reset and hence dc_trigger_sync()
does not resynchronize otg again.

[How]
Implement reset_sync_context_for_pipe() to reset the otg synchronization
context for the disabled pipe and its slave pipes when otg workaround is
applied.

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Display distortion after hotplug 5K tiled display

[Why]
During hot plug of specific 5K tiled display, sometimes both the tiles
are not synchronized resulting in distortion. The reason is that otgs of
both the tiles goes out of sync when otg workaround (dcnxxx_disable_otg_wa)
is applied for bandwidth optimization. The otg workaround reenables otg
but otg synchronization context is not reset and hence dc_trigger_sync()
does not resynchronize otg again.

[How]
Implement reset_sync_context_for_pipe() to reset the otg synchronization
context for the disabled pipe and its slave pipes when otg workaround is
applied.

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Clean up some inconsistent indenting

No functional modification involved.

smatch warning:

drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c:683 dcn316_clk_mgr_construct() warn: inconsistent indenting.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "drm/amd/display: Pass the new context into disable OTG WA"

This reverts commit 8440f57532496d398a461887e56ca6f45089fbcf.

Causes a hang when hotplugging DP, shutting down system, or
enabling dual eDP.

Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "drm/amd/display: Pass the new context into disable OTG WA"

This reverts commit 8440f57532496d398a461887e56ca6f45089fbcf.

Causes a hang when hotplugging DP, shutting down system, or
enabling dual eDP.

Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Pass the new context into disable OTG WA

[Why]
When enabling an HPO stream for the first time after having previously
enabled a DIO stream there may be lingering DIO FIFO errors even though
the DIO is no longer enabled.

These can cause display clock change to hang if we don't apply the
OTG disable workaround since the ramping logic is tied to OTG on.

[How]
The workaround wasn't being applied in the sequence of:

1 DIO stream
0 streams
1 HPO stream

because current_state has no stream or planes in its context - and
it's only swapped after optimize has finished.

We should be using the incoming context instead to determine whether
this logic is needed or not.

Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: revert Blank eDP on disable/enable drv

why and how:
Revert this change. It was causing a black screen with certain blocks

Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leung, Martin <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Check zero planes for OTG disable W/A on clock change

[Why]
A display clock change hang can occur when switching between DIO and HPO
enabled modes during the optimize_bandwidth in dc_commit_state_no_check
call.

This happens when going from 4k120 8bpc 420 to 4k144 10bpc 444.

Display clock in the DIO case is 1200MHz, but pixel rate is 600MHz
because the pixel format is 420.

Display clock in the HPO case is less (800MHz?) because of ODM combine
which results in a smaller divider.

The DIO is still active in prepare but not active in the optimize which
results in the hang occuring.

During this change there are no planes on the stream so it's safe to
apply the workaround, but dpms_off = false and signal type is not
virtual.

[How]
Check for plane_count == 0, no planes on the stream.

It's easiest to check pipe->plane_state == NULL as an equivalent check
rather than trying to search for the stream status in the context
associated with the stream, so let's do that.

The primary, non MPO pipe should not have a NULL plane state.

Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: remove dtbclk_ss compensation for dcn316

[why]
dcn316's dtbclk is from non_ss clock source.
no compensation required here.

Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: remove dtbclk_ss compensation for dcn316

[why]
dcn316's dtbclk is from non_ss clock source.
no compensation required here.

Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix compile error from TO_CLK_MGR_INTERNAL

[Why]

On LNX, TO_CLK_MGR_INTERNAL() only works to get clk_mgr_internal from a
given clk_mgr. In clk_mgr_dcn316 struct, the clk_mgr_internal is already
a memeber by the alias 'base'

[How]

Use &clk_mgr->base instead.

Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: enable dcn315/316 s0i2 support

[why]
enable the support in driver, let the control by CMOS

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix DC definition of PMFW Pstate table for DCN316

[Why]

During DC init, we read power management tables from PMFW. This info is
exchanged in the form of a binary blob inside gpu memory. In order to
parse the binary blob, the correct struct needs to be used.

[How]

Fix dcn316's definition of the DfPstateTable_t struct to align with PMFW

Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Turn global functions into static functions

Turn previously global functions into static functions to avoid
-Wmissing-prototype warnings, such as:

drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn30/irq_service_dcn30.c:50:20:
warning: no previous prototype for function 'to_dal_irq_source_dcn30'
[-Wmissing-prototypes]
enum dc_irq_source to_dal_irq_source_dcn30(
^
drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn30/irq_service_dcn30.c:50:1:
note: declare 'static' if the function is not intended to be used outside
of this translation unit
enum dc_irq_source to_dal_irq_source_dcn30(
^
static
1 warning generated.

drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c:488:6:
warning: no previous prototype for function
'dcn316_clk_mgr_helper_populate_bw_params' [-Wmissing-prototypes]
void dcn316_clk_mgr_helper_populate_bw_params(
^
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c:488:1:
note: declare 'static' if the function is not intended to be used outside
of this translation unit
void dcn316_clk_mgr_helper_populate_bw_params(
^
static
1 warning generated.

v2: drop is_timing_changed hunk (Alex)

Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DCN316 resource and SMU clock manager

Add core DC implementation for DCN316.

Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>