Copy stable/11@r303970 to releng/11.0 as part of the 11.0-RELEASE
cycle.

Prune svn:mergeinfo from the new branch, and rename it to RC1.

Update __FreeBSD_version.

Use the quarterly branch for the default FreeBSD.conf pkg(8) repo and
the dvd1.iso packages population.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head@r302406 to stable/11 as part of the 11.0-RELEASE cycle.
Prune svn:mergeinfo from the new branch, as nothing has been merged
here.

Additional commits post-branch will follow.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Convert Allwinner port to extres clk/hwreset/regulator APIs.

Reviewed by: andrew, gonzo, Emmanuel Vadot <manu@bidouilliste.com>
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5752

Move the Allwinner kernels to use fdt_pinctrl. This will read the pin
configuration from the FDT data, then set the pins into the requested
state. As part of this the gpio controller now reports the correct number
of pins instead of returning the number of bank * 32.

To allow for a future consolidated kernel we add the SOC_ALLWINNER_A10 and
SOC_ALLWINNER_A20 kernel options. These need to be set as appropriate for
the SoC the kernel will boot on.

Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5177

Update of the Allwinner drivers to:
* Use the Linux compat string
* Use EARLY_DRIVER_MODULE to attach at the right time
* Add a generic A10 kernel config file
* A20 now use generic_timer
* Add two new dts files for Olimex boards
* Update our custom DTS file for A10 and A20 to use the same compatible
property names as the vendor ones.

Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4792

Rename a10_emac_gpio_config() to a10_gpio_ethernet_activate() to make the
change to GMAC easier on A20 SoCs.

On A10 only the EMAC controller is available (fast ethernet), but on A20
there is also GMAC a high (or better) performant controller (gigabit
ethernet).

On A20 the both controllers uses the same pins to talk to the ethernet PHY
(MII or RGMII) and they can be selected by the GPIO pin mux.

There is work in progress to bring in GMAC support.

Simplify the receiver code a bit.

Drain the RX FIFO and continue on failure.

Add the necessary support to use both TX queues available on if_emac.

Each TX queue can hold one packet (yes, if_emac can send only two(!)
packets at a time).

Even with this change the very limited FIFO buffer (3 KiB for TX and 13 KiB
for RX) fill up too quick to sustain higher throughput.

For the TCP case it turns out that TX isn't the limiting factor, but the RX
side is (the FIFO fill up and starts to discard packets, so the sender has
to slow down).

Remove unnecessary checks and fix an issue where the interrupt handler
could return with lock held.

Fix the 'wrong packet header' errors for if_emac.

Do not strip the ethernet CRC until we read all data from FIFO, otherwise
the CRC bytes would be left in FIFO causing the failure of next packet
(wrong packet header).

When this error happens the receiver has to be disabled and the RX FIFO
flushed, discarding valid packets.

With this fix if_emac behaves a lot better.

Mechanically convert to if_inc_counter().

Switch to my freebsd.org emal address in copyright.

Approved by: stas (mentor)

Add EMAC 10/100 Ethernet controller driver for A10/A20.
It is available mostly in A10 devices like Hackberry, Marsboard,
Mele A1000, A2000, A100 HTPC, cubieboard1 and A20 device
like cubieboard2.
TX performance can be improved using both channels 0 and 1.
RX performance is poor and needs improvement with the assistance of
external DMA controller in case there is bulk TCP receiver.

Reviewed by: yongari@
Approved by: stas (mentor)