Revert r330897:

This was intended to be a non-functional change. It wasn't. The commit
message was thus wrong. In addition it broke arm, and merged crypto
related code.

Revert with prejudice.

This revert skips files touched in r316370 since that commit was since
MFCed. This revert also skips files that require $FreeBSD$ property
changes.

Thank you to those who helped me get out of this mess including but not
limited to gonzo, kevans, rgrimes.

Requested by: gjb (re)

Partial merge of the SPDX changes

These changes are incomplete but are making it difficult
to determine what other changes can/should be merged.

No objections from: pfg

Copy head@r302406 to stable/11 as part of the 11.0-RELEASE cycle.
Prune svn:mergeinfo from the new branch, as nothing has been merged
here.

Additional commits post-branch will follow.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Add support for the uart classes to set their default register shift value.
This is needed with the pl011 driver. Before this change it would default
to a shift of 0, however the hardware places the registers at 4-byte
addresses meaning the value should be 2.

This patch fixes this for the pl011 when configured using the fdt. The
other drivers have a default value of 0 to keep this a no-op.

MFC after: 1 week

Introduce grab and ungrab upcalls. When the kernel desires to grab the
console, it calls the grab functions. These functions should turn off
the RX interrupts, and any others that interfere. This makes mountroot
prompt work again. If there's more generalized need other than
prompting, many of these routines should be expanded to do those new
things.

Reviewed by: bde (with reservations)

Octeon 2 (6xxx) and newer CPUs don't use the clock CPU speed for its
I/O clock. Thankfully, the simple executive provies a way to querry
the proper clock that works on all models. Move to asking for the SCLK
via this interface.

This gets the serial console working after we start init and open the
console and set the divisor (which turned the output from good to
bad). I can login on the console now.

Use Simple Executive LED display routines, which correctly use the LED base
address passed from the bootloader, rather than using a hard-coded value.

Make FreeBSD announce itself on the LED display similar to other kernels.

Remove uses of the previous LED routines, which were under-used and only used
in drivers for what seem like debugging purposes, despite those drivers being
widely-tested.

Remove several inlines for accessing memory that duplicate other functions
which are now used instead, as they are now entirely unused.

Merge the Cavium Octeon SDK 2.3.0 Simple Executive code and update FreeBSD to
make use of it where possible.

This primarily brings in support for newer hardware, and FreeBSD is not yet
able to support the abundance of IRQs on new hardware and many features in the
Ethernet driver.

Because of the changes to IRQs in the Simple Executive, we have to maintain our
own list of Octeon IRQs now, which probably can be pared-down and be specific
to the CIU interrupt unit soon, and when other interrupt mechanisms are added
they can maintain their own definitions.

Remove unmasking of interrupts from within the UART device now that the
function used is no longer present in the Simple Executive. The unmasking
seems to have been gratuitous as this is more properly handled by the buses
above the UART device, and seems to work on that basis.

Rather than shifting offsets by three, set register offset to 3. All our
bus interface does that's special here now is to use a 64-bit register size.
In theory, uart(4) ought to support a regsz as well as regshft and support
64-bit registers directly.

Also use the UART class's range rather than a hand-coded 1024 for the address
range.

Update the port of FreeBSD to Cavium Octeon to use the Cavium Simple Executive
library:
o) Increase inline unit / large function growth limits for MIPS to accommodate
the needs of the Simple Executive, which uses a shocking amount of inlining.
o) Remove TARGET_OCTEON and use CPU_CNMIPS to do things required by cnMIPS and
the Octeon SoC.
o) Add OCTEON_VENDOR_LANNER to use Lanner's allocation of vendor-specific
board numbers, specifically to support the MR320.
o) Add OCTEON_BOARD_CAPK_0100ND to hard-wire configuration for the CAPK-0100nd,
which improperly uses an evaluation board's board number and breaks board
detection at runtime. This board is sold by Portwell as the CAM-0100.
o) Add support for the RTC available on some Octeon boards.
o) Add support for the Octeon PCI bus. Note that rman_[sg]et_virtual for IO
ports can not work unless building for n64.
o) Clean up the CompactFlash driver to use Simple Executive macros and
structures where possible (it would be advisable to use the Simple Executive
API to set the PIO mode, too, but that is not done presently.) Also use
structures from FreeBSD's ATA layer rather than structures copied from
Linux.
o) Print available Octeon SoC features on boot.
o) Add support for the Octeon timecounter.
o) Use the Simple Executive's routines rather than local copies for doing reads
and writes to 64-bit addresses and use its macros for various device
addresses rather than using local copies.
o) Rename octeon_board_real to octeon_is_simulation to reduce differences with
Cavium-provided code originally written for Linux. Also make it use the
same simplified test that the Simple Executive and Linux both use rather
than our complex one.
o) Add support for the Octeon CIU, which is the main interrupt unit, as a bus
to use normal interrupt allocation and setup routines.
o) Use the Simple Executive's bootmem facility to allocate physical memory for
the kernel, rather than assuming we know which addresses we can steal.
NB: This may reduce the amount of RAM the kernel reports you as having if
you are leaving large temporary allocations made by U-Boot allocated
when starting FreeBSD.
o) Add a port of the Cavium-provided Ethernet driver for Linux. This changes
Ethernet interface naming from rgmxN to octeN. The new driver has vast
improvements over the old one, both in performance and functionality, but
does still have some features which have not been ported entirely and there
may be unimplemented code that can be hit in everyday use. I will make
every effort to correct those as they are reported.
o) Support loading the kernel on non-contiguous cores.
o) Add very conservative support for harvesting randomness from the Octeon
random number device.
o) Turn SMP on by default.
o) Clean up the style of the Octeon kernel configurations a little and make
them compile with -march=octeon.
o) Add support for the Lanner MR320 and the CAPK-0100nd to the Simple
Executive.
o) Modify the Simple Executive to build on FreeBSD and to build without
executive-config.h or cvmx-config.h. In the future we may want to
revert part of these changes and supply executive-config.h and
cvmx-config.h and access to the options contained in those files via
kernel configuration files.
o) Modify the Simple Executive USB routines to support getting and setting
of the USB PID.

Remove redundant checking of sc_leaving (uart_intr() already handles this).

Approved by: marcel

Cope with the move and if_timer going way.

Merge from projects/mips to head by hand:

Copy the support files for the Octeon 1 CPU from sys/mips/octeon1 on
the projects/mips side to sys/mips/cavium on the head side to conform
to the other vendor code. This code was contributed by Cavium to the
project and forward ported by Warner Losh, with some additional code
from Randal Stewart.

# I'll fix the building problems the move creates in a future commit.

Include Octeon specific registers since we mess with them here...

- MFC

Move octeon specific uart goo here, per SOP for other MIPS ports.

Move dev/flash/ cf driver into octeon dir where it belongs.