Copy head@r302406 to stable/11 as part of the 11.0-RELEASE cycle.
Prune svn:mergeinfo from the new branch, as nothing has been merged
here.

Additional commits post-branch will follow.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

[ath_hal] add QCA9565 bluteooth antenna control.

This configures the LNA antenna diversity control, which should be on
if wlan owns the LNA for bluetooth coexistence. Otherwise, make sure
it's off.

I think this is eventually intended to allow 1-antenna bluetooth +
wifi setups for QCA9565, but I'm not sure where that's actually configured
in ath9k.

Obtained from: Linux ath9k

Add initial support for the QCA953x SoC (honeybee) wifi.

This is a 2x2 2GHz 802.11n part. It works enough at the moment to
bring up, scan and associate. I haven't started using this as
a day to day AP.

The specifics:

* add honeybee initvals
* add in changes; a mix from the QCA HAL and ath9k;
* fix a bug in AR_SREV_AR9580_10_OR_LATER(), which is only used
for one capability check and we don't even implement it - so it's
a big no-op.

Shady things:

* ath9k has the "platform data" define the 25/40MHz clock.
This HAL .. doesn't. Honeybee gets hard-coded to 25MHz which
it likely shouldn't be. I'll have to go and identify/fix those.

Tested:

* Qualcomm Atheros AP143 reference design board.

Obtained from: Qualcomm Atheros; Linux ath9k

Add support for the tuning cap for Hornet/AR9331 boards.

This dramatically improves RX sensitivity and behaviour on the
AR9331 hardware I have, including the Carambola 2.

Tested:

* AR9331, Carambola 2 board

Submitted by: Zilvinas Valinskas <zilvinas.valinskas@gmail.com>

Update the AR9300 HAL to the latest public available HAL from QCA.

I've been sitting on this for a year or so now; I've finally
tested it on enough devices to be reasonably sure it won't
cause too much drama. But, if you see issues, please email me.

Tested (all STA mode):

PCIe:

* AR9380
* AR9390
* AR9580
* AR9462
* AR9485

SoC:

* QCA9550
* AR9331
* AR9342

Add initial support for the AR9485 CUS198 / CUS230 variants.

These variants have a few differences from the default AR9485 NIC,
namely:

* a non-default antenna switch config;
* slightly different RX gain table setup;
* an external XLNA hooked up to a GPIO pin;
* (and not yet done) RSSI threshold differences when
doing slow diversity.

To make this possible:

* Add the PCI device list from Linux ath9k, complete with vendor and
sub-vendor IDs for various things to be enabled;
* .. and until FreeBSD learns about a PCI device list like this,
write a search function inspired by the USB device enumeration code;
* add HAL_OPS_CONFIG to the HAL attach methods; the HAL can use this
to initialise its local driver parameters upon attach;
* copy these parameters over in the AR9300 HAL;
* don't default to override the antenna switch - only do it for
the chips that require it;
* I brought over ar9300_attenuation_apply() from ath9k which is cleaner
and easier to read for this particular NIC.

This is a work in progress. I'm worried that there's some post-AR9380
NIC out there which doesn't work without the antenna override set as
I currently haven't implemented bluetooth coexistence for the AR9380
and later HAL. But I'd rather have this code in the tree and fix it
up before 11.0-RELEASE happens versus having a set of newer NICs
in laptops be effectively RX deaf.

Tested:

* AR9380 (STA)
* AR9485 CUS198 (STA)

Obtained from: Qualcomm Atheros, Linux ath9k

Bring over my FreeBSD modifications for the AR9300 HAL to make it
work in FreeBSD.

This is still heavily a work in progress but I'd rather it start
shipping in -HEAD sooner rather than later.

This doesn't (yet) link it into the build system either for a static
kernel or as a module; that will come later (after many, many make universe
tests.)

Copy the vendor branch ar9300 code from qcamain_open_hal into this
directory.

Only copy the ar9300 HAL, we don't want to grab everything.

Initial import of the QCA qcamain_open_hal repository.

Source: https://github.com/qca/qcamain_open_hal_public
Revision: 60390a9f9ac6a20db168fbbc01a4ad4e01c395ce

Thankyou to QCA for this release.