- Copy stable/10@296371 to releng/10.3 in preparation for 10.3-RC1
builds.
- Update newvers.sh to reflect RC1.
- Update __FreeBSD_version to reflect 10.3.
- Update default pkg(8) configuration to use the quarterly branch.

Approved by: re (implicit)

MFC r274724:
cxgbe(4): figure out the max payload size and save it for later.

MFC r266571, r266757, r268536, r269076, r269364, r269366, r269411,
r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe
portion of r270063.

r266571:
cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet.

r266757:
cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards.
Netmap gets its own hardware-assisted virtual interface and won't take
over or disrupt the "normal" interface in any way. You can use both
simultaneously.

For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface
(note the 'n' prefix) in the hardware to accompany each cxl<N>
interface. These two ifnet's per port share the same wire but really
are separate interfaces in the hardware and software. Each gets its own
L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You
should run netmap on the 'n' interfaces only, that's what they are for.

With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port
of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now.
Single port receive is at 33Mpps but this is very much a work in
progress. I expect it to be closer to 40Mpps once done. In any case
the current effort can already saturate multiple 10G ports of a T5 card
at the smallest legal packet size. T4 gear is totally untested.

trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43:ab:cd:ef
881.952141 main [1621] interface is ncxl0
881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0
881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0
881.962540 main [1804] mapped 334980KB at 0x801dff000
Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus.
10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43:ab:cd:ef)
881.962562 main [1882] Sending 512 packets every 0.000000000 s
881.962563 main [1884] Wait 2 secs for phy reset
884.088516 main [1886] Ready...
884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1
884.088607 sender_body [996] start
884.093246 sender_body [1064] drop copy
885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec)
886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec)
887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec)
888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec)
889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec)
890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec)
891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec)
892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec)
893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec)
894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec)
895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec)
896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec)
...

r268536:
cxgbe(4): Add an iSCSI softc to the adapter structure.

r269076:
Some hooks in cxgbe(4) for the offloaded iSCSI driver.

r269364:
Improve compliance with style.Makefile(5).

r269366:
List one file per line in the Makefiles. This makes it easier to read
diffs when a file is added or removed.

r269411:
cxgbe(4): minor optimizations in ingress queue processing.

Reorganize struct sge_iq. Make the iq entry size a compile time
constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly.

r269413:
cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell
address of an egress queue.

r269428:
cxgbe(4): some optimizations in freelist handling.

r269440:
cxgbe(4): Remove an unused version of t4_enable_vi.

r269537:
cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when
IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global
mutex around ifpromisc in at least the bpf_dtor path.

r269644:
cxgbe(4): Let caller specify whether it's ok to sleep in
t4_sched_config and t4_sched_params.

r269731:
cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa).

Relnotes: Yes (native netmap support for Chelsio T4/T5 cards)

MFC r268640 and r268989.

r268640:
Allow multi-byte reads in the private CHELSIO_T4_GET_I2C ioctl. The
firmware allows up to 48B to be read this way but the driver limits
itself to 8B at a time to remain compatible with old cxgbetool
binaries.

r268989:
Add missing newline to an error message.

MFC r259382:

Read card capabilities after firmware initialization, instead of setting
them up as part of firmware initialization (which the driver gets to do
only if it's the master driver).

Read the range of tids available for the ETHOFLD functionality if it's
enabled.

New is_ftid() and is_etid() functions to test whether a tid falls within
the range of filter tids or ETHOFLD tids respectively.

MFC r257654, r257772, r258441, r258689, r258698, r258879, r259048, and
r259103.

r257654:
cxgbe(4): Exclude MPS_RPLC_MAP_CTL (0x11114) from the register dump. Turns
out it's a write-only register with strange side effects on read.

r257772:
cxgbe(4): Tidy up the display for payload memory statistics (pm_stats).

r258441:
cxgbe(4): update the internal list of device features.

r258689:
Disable an assertion that relies on some code[1] that isn't in HEAD yet.

r258698:
cxgbetool: "modinfo" command to display SFP+ module information.

r258879:
cxgbe(4): T4_SET_SCHED_CLASS and T4_SET_SCHED_QUEUE ioctls to program
scheduling classes in the chip and to bind tx queue(s) to a scheduling
class respectively. These can be used for various kinds of tx traffic
throttling (to force selected tx queues to drain at a fixed Kbps rate,
or a % of the port's total bandwidth, or at a fixed pps rate, etc.).

r259048:
Two new cxgbetool subcommands to set up scheduler classes and to bind
them to NIC queues.

r259103:
cxgbe(4): save a copy of the RSS map for each port for the driver's use.

MFC r256459.

cxgbe(4): Update T4 and T5 firmwares to 1.9.12.0

Approved by: re (glebius)

Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

- Read all TP parameters in one place.
- Read the filter mode, calculate various shifts, and use them
properly during active open (in select_ntuple).

MFC after: 1 day

- Include the T5 firmware with the driver.
- Update the T4 firmware to the latest.
- Minor reorganization and updates to the version macros, etc.

Obtained from: Chelsio
MFC after: 1 day

cxgbe(4): Some updates to shared code.

Obtained from: Chelsio
MFC after: 1 week

cxgbe(4): Add support for Chelsio's Terminator 5 (aka T5) ASIC. This
includes support for the NIC and TOE features of the 40G, 10G, and
1G/100M cards based on the T5.

The ASIC is mostly backward compatible with the Terminator 4 so cxgbe(4)
has been updated instead of writing a brand new driver. T5 cards will
show up as cxl (short for cxlgb) ports attached to the t5nex bus driver.

Sponsored by: Chelsio

cxgbe(4): Consider all the API versions of the interfaces exported by
the firmware (instead of just the main firmware version) when evaluating
firmware compatibility. Document the new "hw.cxgbe.fw_install" knob
being introduced here.

This should fix kern/173584 too. Setting hw.cxgbe.fw_install=2 will
mostly do what was requested in the PR but it's a bit more intelligent
in that it won't reinstall the same firmware repeatedly if the knob is
left set.

PR: kern/173584
MFC after: 5 days

cxgbe(4): Update firmware to 1.8.4.0.

MFC after: 5 days

Add a driver ioctl to read a byte from any device on a port's i2c bus.
This lets userspace read arbitrary information from the SFP+ modules
etc. on this bus.

Reading multiple bytes in the same transaction isn't possible right now.
I'll update the driver once the chip's firmware supports this.

MFC after: 3 days

Update interface to firmware 1.6.2 and include the firmware in the driver.

Obtained from: Chelsio
MFC after: 1 week

cxgbe(4): update to firmware interface 1.5.2.0; updates to shared code.

Many updates to cxgbe(4)

- Device configuration via plain text config file. Also able to operate
when not attached to the chip as the master driver.

- Generic "work request" queue that serves as the base for both ctrl and
ofld tx queues.

- Generic interrupt handler routine that can process any event on any
kind of ingress queue (via a dispatch table).

- A couple of new driver ioctls. cxgbetool can now install a firmware
to the card ("loadfw" command) and can read the card's memory
("memdump" and "tcb" commands).

- Lots of assorted information within dev.t4nex.X.misc.* This is
primarily for debugging and won't show up in sysctl -a.

- Code to manage the L2 tables on the chip.

- Updates to cxgbe(4) man page to go with the tunables that have changed.

- Updates to the shared code in common/

- Updates to the driver-firmware interface (now at fw 1.4.16.0)

MFC after: 1 month

Update to firmware interface 1.3.10

MFC after: 1 week

Update header and related code for firmware 1.3.8

MFC after: 3 days

Upgrade the firmware on the card automatically if a better version is
available. Downgrade only for a major version mismatch.

MFC after: 1 week

cxgbe(4) - NIC driver for Chelsio T4 (Terminator 4) based 10Gb/1Gb adapters.

MFC after: 3 weeks