1/* $OpenBSD: acphyreg.h,v 1.2 2004/10/01 04:08:45 jsg Exp $ */ 2/* $NetBSD: acphyreg.h,v 1.1 2001/08/24 17:54:33 thorpej Exp $ */ 3 4/* 5 * Copyright 2001 Wasabi Systems, Inc. 6 * All rights reserved. 7 * 8 * Written by Jason R. Thorpe for Wasabi Systems, Inc. 9 * 10 * Redistribution and use in source and binary forms, with or without 11 * modification, are permitted provided that the following conditions 12 * are met: 13 * 1. Redistributions of source code must retain the above copyright 14 * notice, this list of conditions and the following disclaimer. 15 * 2. Redistributions in binary form must reproduce the above copyright 16 * notice, this list of conditions and the following disclaimer in the 17 * documentation and/or other materials provided with the distribution. 18 * 3. All advertising materials mentioning features or use of this software 19 * must display the following acknowledgement: 20 * This product includes software developed for the NetBSD Project by 21 * Wasabi Systems, Inc. 22 * 4. The name of Wasabi Systems, Inc. may not be used to endorse 23 * or promote products derived from this software without specific prior 24 * written permission. 25 * 26 * THIS SOFTWARE IS PROVIDED BY WASABI SYSTEMS, INC. ``AS IS'' AND 27 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 28 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 29 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL WASABI SYSTEMS, INC 30 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 31 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 32 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 33 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 34 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 35 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 36 * POSSIBILITY OF SUCH DAMAGE. 37 */ 38 39#ifndef _DEV_MII_ACPHYREG_H_ 40#define _DEV_MII_ACPHYREG_H_ 41 42/* 43 * Altima AC101 PHY registers. 44 * 45 * Note the AC101 and the AMD Ac79c874 are the same PHY core. There 46 * are some registers documented in the AC101 manual that are not in 47 * the Am79c874 manual, and vice-versa. I have no idea how to tell 48 * the two apart, but we don't really use the registers that fall into 49 * this category, anyhow. 50 */ 51 52#define MII_ACPHY_PILR 0x10 /* polarity and interrupt control */ 53#define PILR_REPEATER 0x8000 /* repeater mode */ 54#define PILR_INTR_LEVL 0x4000 /* 1 = active high, 0 = active low */ 55#define PILR_SQE_INHIBIT 0x0800 /* disable 10T SQE testing */ 56#define PILR_10T_LOOP 0x0400 /* enable loopback in 10T */ 57#define PILR_GPIO1_DATA 0x0200 /* GPIO1 pin */ 58#define PILR_GPIO1_DIR 0x0100 /* 1 = input */ 59#define PILR_GPIO0_DATA 0x0080 /* GPIO0 pin */ 60#define PILR_GPIO0_DIR 0x0040 /* 1 = input */ 61#define PILR_AUTO_POL_DIS 0x0020 /* disable auto-polarity */ 62#define PILR_REVERSE_POL 0x0010 /* 1 = reverse, 0 = normal */ 63#define PILR_RXCLK_CTRL 0x0001 /* disable RX_CLK when idle */ 64 65 66#define MII_ACPHY_ICSR 0x11 /* interrupt control/status */ 67#define ICSR_JABBER_IE 0x8000 /* jabber interrupt enable */ 68#define ICSR_RX_ER_IE 0x4000 /* Rx error interrupt enable */ 69#define ICSR_PAGE_RX_IE 0x2000 /* page received interrupt enable */ 70#define ICSR_PD_FAULT_IE 0x1000 /* parallel detection fault int en */ 71#define ICSR_LP_ACK_IE 0x0800 /* link partner ACK interrupt en */ 72#define ICSR_LNK_NOT_OK_IE 0x0400 /* link not okay interrupt enable */ 73#define ICSR_R_FAULT_IE 0x0200 /* remote fault interrupt enable */ 74#define ICSR_ANEG_COMP_IE 0x0100 /* autonegotiation complete int en */ 75#define ICSR_JABBER_INT 0x0080 /* jabber interrupt */ 76#define ICSR_RX_ER_INT 0x0040 /* Rx error interrupt */ 77#define ICSR_PAGE_RX_INT 0x0020 /* page received interrupt */ 78#define ICSR_PD_FAULT_INT 0x0010 /* parallel detection fault interrupt */ 79#define ICSR_LP_ACK_INT 0x0008 /* link partner ACK interrupt */ 80#define ICSR_LNK_NOT_OK_INT 0x0004 /* link not okay interrupt */ 81#define ICSR_R_FAULT_INT 0x0002 /* remote fault interrupt */ 82#define ICSR_ANEG_COMP_INT 0x0001 /* autonegotiation complete interrupt */ 83 84 85#define MII_ACPHY_DR 0x12 /* diagnostic register */ 86#define DR_DPLX 0x0800 /* full-duplex resolved */ 87#define DR_SPEED 0x0400 /* 100BASE-TX resolved */ 88#define DR_RX_PASS 0x0200 /* manchester/signal received */ 89#define DR_RX_LOCK 0x0100 /* PLL signal has been locked */ 90 91 92#define MII_ACPHY_PLR 0x13 /* power/loopback register */ 93#define PLR_TB125 0x0040 /* Tx transformer ratio 1.25:1 */ 94#define PLR_LOW_POWER_MODE 0x0020 /* enable advanced power saving mode */ 95#define PLR_TEST_LOOPBACK 0x0010 /* enable test loopback */ 96#define PLR_DIGITAL_LOOPBACK 0x0008 /* enable loopback */ 97#define PLR_LP_LPBK 0x0004 /* enable link pulse loopback */ 98#define PLR_NLP_LINK_INT_TEST 0x0002 /* send NLP instead of FLP */ 99#define PLR_REDUCE_TIMER 0x0001 /* reduce time constant for aneg */ 100 101 102/* AC101 only */ 103#define MII_ACPHY_CMR 0x14 /* cable measurement register */ 104#define CMR_MASK 0x00f0 /* cable measurement mask */ 105 106 107#define MII_ACPHY_MCR 0x15 /* mode control register */ 108#define MCR_NLP_DISABLE 0x4000 /* force good 10BASE-T link */ 109#define MCR_FORCE_LINK_UP 0x2000 /* force good 100BASE-TX link */ 110#define MCR_JABBER_DISABLE 0x1000 /* disable jabber function */ 111#define MCR_10BT_SEL 0x0800 /* enable 7-wire 10T operation */ 112#define MCR_CONF_ALED 0x0400 /* 1 = ALED only Rx, 0 = ALED Rx/Tx */ 113#define MCR_LED_SEL 0x0200 /* 1 = tqphy-compat LED config */ 114#define MCR_FEF_DIS 0x0100 /* disable far-end-fault insertion */ 115#define MCR_FORCE_FEF_TX 0x0080 /* force FEF transmission */ 116#define MCR_RX_ER_CNT_FULL 0x0040 /* Rx error counter full */ 117#define MCR_DIS_RX_ER_CNT 0x0020 /* disable Rx error counter */ 118#define MCR_DIS_WDT 0x0010 /* disable the watchdog timer */ 119#define MCR_EN_RPBK 0x0008 /* enable remote loopback */ 120#define MCR_DIS_SCRM 0x0004 /* enable 100M data scrambling */ 121#define MCR_PCSBP 0x0002 /* bypass PCS */ 122#define MCR_FX_SEL 0x0001 /* FX mode selected */ 123 124 125/* Am79c874 only */ 126#define MII_ACPHY_DCR 0x17 /* disconnect counter register */ 127 128 129#define MII_ACPHY_RECR 0x18 /* receive error counter register */ 130 131 132#endif /* _DEV_MII_ACPHYREG_H_ */ 133