$NetBSD: azalia.4,v 1.2 2005/06/22 04:19:09 kent Exp $
Copyright (c) 2005 The NetBSD Foundation, Inc.
All rights reserved.
This code is derived from software contributed to The NetBSD Foundation
by TAMURA Kent
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
.Dd $Mdocdate: September 4 2010 $ .Dt AZALIA 4 .Os .Sh NAME .Nm azalia .Nd generic High Definition Audio device .Sh SYNOPSIS .Cd "azalia* at pci?" .Cd "audio* at azalia?" .Sh DESCRIPTION The .Nm device driver is expected to support any PCI device which is compliant with the High Definition Audio Specification 1.0.
p Supported controllers include:
p l -bullet -compact -offset indent t Acer Labs M5461 t AMD Hudson-2 t ATI SB450, SB600, SB700, SB800 t Intel 82801FB/GB/H/I/JI (ICH6, ICH7, ICH8, ICH9, ICH10) t NVIDIA MCP51/MCP55/MCP61/MCP65/MCP67/MCP73/MCP77/MCP79/MCP89 t Silicon Integrated System 966/966L t VIA Technologies VT8237A, VT8251 .El
p The High Definition Audio (HDA) specification describes a flexible and extensible infrastructure to support high quality audio. HDA supports sample rates up to 192 kHz, bit rates of up to 32 bits per sample, and up to 16 channels in audio streams. It also supports S/PDIF input/output as well as jack retasking and sensing. The HDA specification defines a controller register set and a codec architecture. .Sh MIXER INTERFACE The codec is the main audio processor. Configuration of the device, such as selecting playback sample rate or decreasing the volume, is handled by the codec. Codecs are comprised of interconnected widgets. Common examples of widgets include DACs (digital to analog converter), ADCs (analog to digital converter), selectors, mixers, and pin complexes (input/output jacks). Widgets may have fixed or controllable properties. Some of these properties include source selection, amplifier gain, mute, and operational direction.
p The mixer interface for .Nm is designed to allow the user to control most properties of the widgets. When .Nm first attaches and configures the device, it will set all widgets to unmuted, moderate volume, and configure connections such that stereo playback and recording will work with the expected input/output pins.
p There are a wide range of HDA codecs. Some have only a few widgets that don't have many controllable properties, and some may have many, very controllable widgets. The mixer interface on one .Nm may be very different than the mixer interface on another.
p Mixer item names describe the widget and property being controlled. Names take the following form: d -literal <mixer class>.<widget type>[<widget type enumerator>][_<property>] .Ed
p The mixer class gives a hint as to the purpose of the control. The widget type enumerator is used to distinguish different widgets of the same type. The enumeration starts at 2: the first widget of each type is not enumerated. The enumeration order is meaningless. The property is optional. Generally, if there is no property, the mixer item is an amplifier gain control.
p The following are the widget type names used in mixer control names: l -tag -width "SPDIF-in" t Cm dac Digital to analog converter, usually used for playback. The audio stream channels these widgets will convert are encoded into their name in the form of <start channel>:<end channel>. For example, .Cm dac-0:1 converts channels 0 and 1 (stereo). However, a dac that is connected to built-in speakers or front panel headphone jacks by default will convert audio stream channels starting at 0 if the dac would otherwise not be converting any channels. For example, if .Cm dac-2:3 is the default dac for the built-in speakers in a laptop, .Cm dac-2:3 will convert channels 0 and 1 when a stereo audio stream is being played. This is to allow simultaneous stereo playback on both the built-in speakers and a line or headphone jack. t Cm dig-dac Digital output converter, usually an S/PDIF transmitter. The audio stream channels these widgets will convert are encoded into their name in the form of <start channel>:<end channel>. For example, .Cm dig-dac-0:1 converts channels 0 and 1 (stereo). t Cm adc Analog to digital converter, usually used for recording. The audio stream channels these widgets will convert are encoded into their name in the form of <start channel>:<end channel>. For example, .Cm adc-0:1 converts channels 0 and 1 (stereo). t Cm dig-adc Digital input converter, usually an S/PDIF receiver. The audio stream channels these widgets will convert are encoded into their name in the form of <start channel>:<end channel>. For example, .Cm dig-adc-0:1 converts channels 0 and 1 (stereo). t Cm mix Sums multiple audio sources into a single stream, but sometimes only used for amplifier or mute properties. The property part of a mix widget mixer control name may be the name of another widget. Such a mixer item controls the input level from the widget in the property part of the name. t Cm sel Selects a single audio source, but sometimes used only for amplifier or mute properties. t Cm pow Controls power state for a group of widgets. t Cm volume Interprets data from external controls, such as a volume knob. t Cm beep Creates a tone at a certain frequency. t Cm line Pin complex for a line-level jack that is normally used for analog audio output. The name may also be appended with a color abbreviation such as -grn (green), -blk (black), -org (orange), or -gry (grey), to help differentiate jacks. t Cm spkr Pin complex for a speaker, often built into the machine. t Cm hp Pin complex for a jack that is normally used for output to a headphone. t Cm cd Pin complex for analog audio input from a CD device. t Cm SPDIF Pin complex for an S/PDIF output connector. t Cm line-in Pin complex for a line-level jack that is normally used for analog audio input. t Cm aux Pin complex for an auxiliary analog audio input. t Cm mic Pin complex for analog audio input from a microphone, either a jack or built into the machine. t Cm SPDIF-in Pin complex for an S/PDIF input connector. t Cm beep Pin complex for analog audio input from a beep generator. .El
p The following are the property names used in mixer control names: l -tag -width "source" t Cm mute Mutes input or output audio stream. t Cm source Selects input source. Can either select a single source or multiple sources. Sometimes these controls may only have a single choice, but they are provided to show how audio streams move through the codec. t Cm dir Selects pin direction and input VRef signal. VRef is represented in percent of the analog voltage rail. For example, 'input-vr80' means input direction with 80% VRef. t Cm boost Enables/disables low impedance amplifier, usually for use with headphones. t Cm eapd Powers on/off external amplifier circuitry. t Cm sense Reports current jack sense state. .El
p There are also some special mixer controls that don't directly correspond to properties of the widgets, but control aspects of the driver or other mixer controls. The following describes these special controls: l -tag -width "outputsXmasterXslaves" t Cm outputs.spkr_muters List of pins that can mute a built-in speaker. A pin mutes the speaker by sending a signal when it senses that something has been plugged into its jack. If a pin supports both input and output operation, the pin will only mute the speaker when plugged into if that pin is configured for output. t Cm outputs.master.slaves List of widgets with amplifier gain or mute controls that are configured with the parameters used for .Cm outputs.master and .Cm outputs.master.mute . For example, if .Cm dac is in the list and has an input amplifier gain control, setting .Cm outputs.master to 200 will set .Cm inputs.dac to 200. t Cm outputs.master Amplifier gain control for widgets listed in .Cm outputs.master.slaves . t Cm outputs.master.mute Mute control for widgets listed in .Cm outputs.master.slaves . t Cm record.volume.slaves List of widgets with amplifier gain or mute controls that are configured with the parameters used for .Cm record.volume and .Cm record.volume.mute . For example, if .Cm adc is in the list and has an input amplifier gain control, setting .Cm record.volume to 200 will set .Cm record.adc to 200. t Cm record.volume Amplifier gain control for widgets listed in .Cm record.volume.slaves . t Cm record.volume.mute Mute control for widgets listed in .Cm record.volume.slaves . t Cm outputs.mode Controls whether the digital or analog converters and pins will be used for playback. t Cm record.mode Controls whether the digital or analog converters and pins will be used for recording. .El .Sh SEE ALSO .Xr audio 4 , .Xr pci 4 .Sh HISTORY The .Nm device driver first appeared in .Nx 3.0 . .Ox support first appeared in .Ox 4.0 . .Sh BUGS This driver does not support codecs that are intended for HDMI or DisplayPort connectivity.