1#ifndef _3c523_INCLUDE_ 2#define _3c523_INCLUDE_ 3/* 4 This is basically a hacked version of ni52.h, for the 3c523 5 Etherlink/MC. 6*/ 7 8/* 9 * Intel i82586 Ethernet definitions 10 * 11 * This is an extension to the Linux operating system, and is covered by the 12 * same GNU General Public License that covers that work. 13 * 14 * Copyright 1995 by Chris Beauregard (cpbeaure@undergrad.math.uwaterloo.ca) 15 * 16 * See 3c523.c for details. 17 * 18 * $Header: /projects/cvsroot/src/linux/linux-2.6/drivers/net/3c523.h,v 1.1.1.1 2007/08/03 18:52:44 rnuti Exp $ 19 */ 20 21/* 22 * where to find the System Configuration Pointer (SCP) 23 */ 24#define SCP_DEFAULT_ADDRESS 0xfffff4 25 26 27/* 28 * System Configuration Pointer Struct 29 */ 30 31struct scp_struct 32{ 33 unsigned short zero_dum0; /* has to be zero */ 34 unsigned char sysbus; /* 0=16Bit,1=8Bit */ 35 unsigned char zero_dum1; /* has to be zero for 586 */ 36 unsigned short zero_dum2; 37 unsigned short zero_dum3; 38 char *iscp; /* pointer to the iscp-block */ 39}; 40 41 42/* 43 * Intermediate System Configuration Pointer (ISCP) 44 */ 45struct iscp_struct 46{ 47 unsigned char busy; /* 586 clears after successful init */ 48 unsigned char zero_dummy; /* hast to be zero */ 49 unsigned short scb_offset; /* pointeroffset to the scb_base */ 50 char *scb_base; /* base-address of all 16-bit offsets */ 51}; 52 53/* 54 * System Control Block (SCB) 55 */ 56struct scb_struct 57{ 58 unsigned short status; /* status word */ 59 unsigned short cmd; /* command word */ 60 unsigned short cbl_offset; /* pointeroffset, command block list */ 61 unsigned short rfa_offset; /* pointeroffset, receive frame area */ 62 unsigned short crc_errs; /* CRC-Error counter */ 63 unsigned short aln_errs; /* alignmenterror counter */ 64 unsigned short rsc_errs; /* Resourceerror counter */ 65 unsigned short ovrn_errs; /* OVerrunerror counter */ 66}; 67 68/* 69 * possible command values for the command word 70 */ 71#define RUC_MASK 0x0070 /* mask for RU commands */ 72#define RUC_NOP 0x0000 /* NOP-command */ 73#define RUC_START 0x0010 /* start RU */ 74#define RUC_RESUME 0x0020 /* resume RU after suspend */ 75#define RUC_SUSPEND 0x0030 /* suspend RU */ 76#define RUC_ABORT 0x0040 /* abort receiver operation immediately */ 77 78#define CUC_MASK 0x0700 /* mask for CU command */ 79#define CUC_NOP 0x0000 /* NOP-command */ 80#define CUC_START 0x0100 /* start execution of 1. cmd on the CBL */ 81#define CUC_RESUME 0x0200 /* resume after suspend */ 82#define CUC_SUSPEND 0x0300 /* Suspend CU */ 83#define CUC_ABORT 0x0400 /* abort command operation immediately */ 84 85#define ACK_MASK 0xf000 /* mask for ACK command */ 86#define ACK_CX 0x8000 /* acknowledges STAT_CX */ 87#define ACK_FR 0x4000 /* ack. STAT_FR */ 88#define ACK_CNA 0x2000 /* ack. STAT_CNA */ 89#define ACK_RNR 0x1000 /* ack. STAT_RNR */ 90 91/* 92 * possible status values for the status word 93 */ 94#define STAT_MASK 0xf000 /* mask for cause of interrupt */ 95#define STAT_CX 0x8000 /* CU finished cmd with its I bit set */ 96#define STAT_FR 0x4000 /* RU finished receiving a frame */ 97#define STAT_CNA 0x2000 /* CU left active state */ 98#define STAT_RNR 0x1000 /* RU left ready state */ 99 100#define CU_STATUS 0x700 /* CU status, 0=idle */ 101#define CU_SUSPEND 0x100 /* CU is suspended */ 102#define CU_ACTIVE 0x200 /* CU is active */ 103 104#define RU_STATUS 0x70 /* RU status, 0=idle */ 105#define RU_SUSPEND 0x10 /* RU suspended */ 106#define RU_NOSPACE 0x20 /* RU no resources */ 107#define RU_READY 0x40 /* RU is ready */ 108 109/* 110 * Receive Frame Descriptor (RFD) 111 */ 112struct rfd_struct 113{ 114 unsigned short status; /* status word */ 115 unsigned short last; /* Bit15,Last Frame on List / Bit14,suspend */ 116 unsigned short next; /* linkoffset to next RFD */ 117 unsigned short rbd_offset; /* pointeroffset to RBD-buffer */ 118 unsigned char dest[6]; /* ethernet-address, destination */ 119 unsigned char source[6]; /* ethernet-address, source */ 120 unsigned short length; /* 802.3 frame-length */ 121 unsigned short zero_dummy; /* dummy */ 122}; 123 124#define RFD_LAST 0x8000 /* last: last rfd in the list */ 125#define RFD_SUSP 0x4000 /* last: suspend RU after */ 126#define RFD_ERRMASK 0x0fe1 /* status: errormask */ 127#define RFD_MATCHADD 0x0002 /* status: Destinationaddress !matches IA */ 128#define RFD_RNR 0x0200 /* status: receiver out of resources */ 129 130/* 131 * Receive Buffer Descriptor (RBD) 132 */ 133struct rbd_struct 134{ 135 unsigned short status; /* status word,number of used bytes in buff */ 136 unsigned short next; /* pointeroffset to next RBD */ 137 char *buffer; /* receive buffer address pointer */ 138 unsigned short size; /* size of this buffer */ 139 unsigned short zero_dummy; /* dummy */ 140}; 141 142#define RBD_LAST 0x8000 /* last buffer */ 143#define RBD_USED 0x4000 /* this buffer has data */ 144#define RBD_MASK 0x3fff /* size-mask for length */ 145 146/* 147 * Statusvalues for Commands/RFD 148 */ 149#define STAT_COMPL 0x8000 /* status: frame/command is complete */ 150#define STAT_BUSY 0x4000 /* status: frame/command is busy */ 151#define STAT_OK 0x2000 /* status: frame/command is ok */ 152 153/* 154 * Action-Commands 155 */ 156#define CMD_NOP 0x0000 /* NOP */ 157#define CMD_IASETUP 0x0001 /* initial address setup command */ 158#define CMD_CONFIGURE 0x0002 /* configure command */ 159#define CMD_MCSETUP 0x0003 /* MC setup command */ 160#define CMD_XMIT 0x0004 /* transmit command */ 161#define CMD_TDR 0x0005 /* time domain reflectometer (TDR) command */ 162#define CMD_DUMP 0x0006 /* dump command */ 163#define CMD_DIAGNOSE 0x0007 /* diagnose command */ 164 165/* 166 * Action command bits 167 */ 168#define CMD_LAST 0x8000 /* indicates last command in the CBL */ 169#define CMD_SUSPEND 0x4000 /* suspend CU after this CB */ 170#define CMD_INT 0x2000 /* generate interrupt after execution */ 171 172/* 173 * NOP - command 174 */ 175struct nop_cmd_struct 176{ 177 unsigned short cmd_status; /* status of this command */ 178 unsigned short cmd_cmd; /* the command itself (+bits) */ 179 unsigned short cmd_link; /* offsetpointer to next command */ 180}; 181 182/* 183 * IA Setup command 184 */ 185struct iasetup_cmd_struct 186{ 187 unsigned short cmd_status; 188 unsigned short cmd_cmd; 189 unsigned short cmd_link; 190 unsigned char iaddr[6]; 191}; 192 193/* 194 * Configure command 195 */ 196struct configure_cmd_struct 197{ 198 unsigned short cmd_status; 199 unsigned short cmd_cmd; 200 unsigned short cmd_link; 201 unsigned char byte_cnt; /* size of the config-cmd */ 202 unsigned char fifo; /* fifo/recv monitor */ 203 unsigned char sav_bf; /* save bad frames (bit7=1)*/ 204 unsigned char adr_len; /* adr_len(0-2),al_loc(3),pream(4-5),loopbak(6-7)*/ 205 unsigned char priority; /* lin_prio(0-2),exp_prio(4-6),bof_metd(7) */ 206 unsigned char ifs; /* inter frame spacing */ 207 unsigned char time_low; /* slot time low */ 208 unsigned char time_high; /* slot time high(0-2) and max. retries(4-7) */ 209 unsigned char promisc; /* promisc-mode(0) , et al (1-7) */ 210 unsigned char carr_coll; /* carrier(0-3)/collision(4-7) stuff */ 211 unsigned char fram_len; /* minimal frame len */ 212 unsigned char dummy; /* dummy */ 213}; 214 215/* 216 * Multicast Setup command 217 */ 218struct mcsetup_cmd_struct 219{ 220 unsigned short cmd_status; 221 unsigned short cmd_cmd; 222 unsigned short cmd_link; 223 unsigned short mc_cnt; /* number of bytes in the MC-List */ 224 unsigned char mc_list[0][6]; /* pointer to 6 bytes entries */ 225}; 226 227/* 228 * transmit command 229 */ 230struct transmit_cmd_struct 231{ 232 unsigned short cmd_status; 233 unsigned short cmd_cmd; 234 unsigned short cmd_link; 235 unsigned short tbd_offset; /* pointeroffset to TBD */ 236 unsigned char dest[6]; /* destination address of the frame */ 237 unsigned short length; /* user defined: 802.3 length / Ether type */ 238}; 239 240#define TCMD_ERRMASK 0x0fa0 241#define TCMD_MAXCOLLMASK 0x000f 242#define TCMD_MAXCOLL 0x0020 243#define TCMD_HEARTBEAT 0x0040 244#define TCMD_DEFERRED 0x0080 245#define TCMD_UNDERRUN 0x0100 246#define TCMD_LOSTCTS 0x0200 247#define TCMD_NOCARRIER 0x0400 248#define TCMD_LATECOLL 0x0800 249 250struct tdr_cmd_struct 251{ 252 unsigned short cmd_status; 253 unsigned short cmd_cmd; 254 unsigned short cmd_link; 255 unsigned short status; 256}; 257 258#define TDR_LNK_OK 0x8000 /* No link problem identified */ 259#define TDR_XCVR_PRB 0x4000 /* indicates a transceiver problem */ 260#define TDR_ET_OPN 0x2000 /* open, no correct termination */ 261#define TDR_ET_SRT 0x1000 /* TDR detected a short circuit */ 262#define TDR_TIMEMASK 0x07ff /* mask for the time field */ 263 264/* 265 * Transmit Buffer Descriptor (TBD) 266 */ 267struct tbd_struct 268{ 269 unsigned short size; /* size + EOF-Flag(15) */ 270 unsigned short next; /* pointeroffset to next TBD */ 271 char *buffer; /* pointer to buffer */ 272}; 273 274#define TBD_LAST 0x8000 /* EOF-Flag, indicates last buffer in list */ 275 276/*************************************************************************/ 277/* 278Verbatim from the Crynwyr stuff: 279 280 The 3c523 responds with adapter code 0x6042 at slot 281registers xxx0 and xxx1. The setup register is at xxx2 and 282contains the following bits: 283 2840: card enable 2852,1: csr address select 286 00 = 0300 287 01 = 1300 288 10 = 2300 289 11 = 3300 2904,3: shared memory address select 291 00 = 0c0000 292 01 = 0c8000 293 10 = 0d0000 294 11 = 0d8000 2955: set to disable on-board thinnet 2967,6: (read-only) shows selected irq 297 00 = 12 298 01 = 7 299 10 = 3 300 11 = 9 301 302The interrupt-select register is at xxx3 and uses one bit per irq. 303 3040: int 12 3051: int 7 3062: int 3 3073: int 9 308 309 Again, the documentation stresses that the setup register 310should never be written. The interrupt-select register may be 311written with the value corresponding to bits 7.6 in 312the setup register to insure corret setup. 313*/ 314 315/* Offsets from the base I/O address. */ 316#define ELMC_SA 0 /* first 6 bytes are IEEE network address */ 317#define ELMC_CTRL 6 /* control & status register */ 318#define ELMC_REVISION 7 /* revision register, first 4 bits only */ 319#define ELMC_IO_EXTENT 8 320 321/* these are the bit selects for the port register 2 */ 322#define ELMC_STATUS_ENABLED 0x01 323#define ELMC_STATUS_CSR_SELECT 0x06 324#define ELMC_STATUS_MEMORY_SELECT 0x18 325#define ELMC_STATUS_DISABLE_THIN 0x20 326#define ELMC_STATUS_IRQ_SELECT 0xc0 327 328/* this is the card id used in the detection code. You might recognize 329it from @6042.adf */ 330#define ELMC_MCA_ID 0x6042 331 332/* 333 The following define the bits for the control & status register 334 335 The bank select registers can be used if more than 16K of memory is 336 on the card. For some stupid reason, bank 3 is the one for the 337 bottom 16K, and the card defaults to bank 0. So we have to set the 338 bank to 3 before the card will even think of operating. To get bank 339 3, set BS0 and BS1 to high (of course...) 340*/ 341#define ELMC_CTRL_BS0 0x01 /* RW bank select */ 342#define ELMC_CTRL_BS1 0x02 /* RW bank select */ 343#define ELMC_CTRL_INTE 0x04 /* RW interrupt enable, assert high */ 344#define ELMC_CTRL_INT 0x08 /* R interrupt active, assert high */ 345/*#define ELMC_CTRL_* 0x10*/ /* reserved */ 346#define ELMC_CTRL_LBK 0x20 /* RW loopback enable, assert high */ 347#define ELMC_CTRL_CA 0x40 /* RW channel attention, assert high */ 348#define ELMC_CTRL_RST 0x80 /* RW 82586 reset, assert low */ 349 350/* some handy compound bits */ 351 352/* normal operation should have bank 3 and RST high, ints enabled */ 353#define ELMC_NORMAL (ELMC_CTRL_INTE|ELMC_CTRL_RST|0x3) 354 355#endif /* _3c523_INCLUDE_ */ 356