1/************************************************************************/ 2/* */ 3/* dc395x.h */ 4/* */ 5/* Device Driver for Tekram DC395(U/UW/F), DC315(U) */ 6/* PCI SCSI Bus Master Host Adapter */ 7/* (SCSI chip set used Tekram ASIC TRM-S1040) */ 8/* */ 9/************************************************************************/ 10#ifndef DC395x_H 11#define DC395x_H 12 13/************************************************************************/ 14/* */ 15/* Initial values */ 16/* */ 17/************************************************************************/ 18#define DC395x_MAX_CMD_QUEUE 32 19/* #define DC395x_MAX_QTAGS 32 */ 20#define DC395x_MAX_QTAGS 16 21#define DC395x_MAX_SCSI_ID 16 22#define DC395x_MAX_CMD_PER_LUN DC395x_MAX_QTAGS 23#define DC395x_MAX_SG_TABLESIZE 64 /* HW limitation */ 24#define DC395x_MAX_SG_LISTENTRY 64 /* Must be equal or lower to previous */ 25 /* item */ 26#define DC395x_MAX_SRB_CNT 63 27/* #define DC395x_MAX_CAN_QUEUE 7 * DC395x_MAX_QTAGS */ 28#define DC395x_MAX_CAN_QUEUE DC395x_MAX_SRB_CNT 29#define DC395x_END_SCAN 2 30#define DC395x_SEL_TIMEOUT 153 /* 250 ms selection timeout (@ 40 MHz) */ 31#define DC395x_MAX_RETRIES 3 32 33 34#define NORM_REC_LVL 0 35 36/************************************************************************/ 37/* */ 38/* Various definitions */ 39/* */ 40/************************************************************************/ 41#define BIT31 0x80000000 42#define BIT30 0x40000000 43#define BIT29 0x20000000 44#define BIT28 0x10000000 45#define BIT27 0x08000000 46#define BIT26 0x04000000 47#define BIT25 0x02000000 48#define BIT24 0x01000000 49#define BIT23 0x00800000 50#define BIT22 0x00400000 51#define BIT21 0x00200000 52#define BIT20 0x00100000 53#define BIT19 0x00080000 54#define BIT18 0x00040000 55#define BIT17 0x00020000 56#define BIT16 0x00010000 57#define BIT15 0x00008000 58#define BIT14 0x00004000 59#define BIT13 0x00002000 60#define BIT12 0x00001000 61#define BIT11 0x00000800 62#define BIT10 0x00000400 63#define BIT9 0x00000200 64#define BIT8 0x00000100 65#define BIT7 0x00000080 66#define BIT6 0x00000040 67#define BIT5 0x00000020 68#define BIT4 0x00000010 69#define BIT3 0x00000008 70#define BIT2 0x00000004 71#define BIT1 0x00000002 72#define BIT0 0x00000001 73 74/* UnitCtrlFlag */ 75#define UNIT_ALLOCATED BIT0 76#define UNIT_INFO_CHANGED BIT1 77#define FORMATING_MEDIA BIT2 78#define UNIT_RETRY BIT3 79 80/* UnitFlags */ 81#define DASD_SUPPORT BIT0 82#define SCSI_SUPPORT BIT1 83#define ASPI_SUPPORT BIT2 84 85/* SRBState machine definition */ 86#define SRB_FREE 0x0000 87#define SRB_WAIT 0x0001 88#define SRB_READY 0x0002 89#define SRB_MSGOUT 0x0004 /* arbitration+msg_out 1st byte */ 90#define SRB_MSGIN 0x0008 91#define SRB_EXTEND_MSGIN 0x0010 92#define SRB_COMMAND 0x0020 93#define SRB_START_ 0x0040 /* arbitration+msg_out+command_out */ 94#define SRB_DISCONNECT 0x0080 95#define SRB_DATA_XFER 0x0100 96#define SRB_XFERPAD 0x0200 97#define SRB_STATUS 0x0400 98#define SRB_COMPLETED 0x0800 99#define SRB_ABORT_SENT 0x1000 100#define SRB_DO_SYNC_NEGO 0x2000 101#define SRB_DO_WIDE_NEGO 0x4000 102#define SRB_UNEXPECT_RESEL 0x8000 103 104/************************************************************************/ 105/* */ 106/* ACB Config */ 107/* */ 108/************************************************************************/ 109#define HCC_WIDE_CARD 0x20 110#define HCC_SCSI_RESET 0x10 111#define HCC_PARITY 0x08 112#define HCC_AUTOTERM 0x04 113#define HCC_LOW8TERM 0x02 114#define HCC_UP8TERM 0x01 115 116/* ACBFlag */ 117#define RESET_DEV BIT0 118#define RESET_DETECT BIT1 119#define RESET_DONE BIT2 120 121/* DCBFlag */ 122#define ABORT_DEV_ BIT0 123 124/* SRBstatus */ 125#define SRB_OK BIT0 126#define ABORTION BIT1 127#define OVER_RUN BIT2 128#define UNDER_RUN BIT3 129#define PARITY_ERROR BIT4 130#define SRB_ERROR BIT5 131 132/* SRBFlag */ 133#define DATAOUT BIT7 134#define DATAIN BIT6 135#define RESIDUAL_VALID BIT5 136#define ENABLE_TIMER BIT4 137#define RESET_DEV0 BIT2 138#define ABORT_DEV BIT1 139#define AUTO_REQSENSE BIT0 140 141/* Adapter status */ 142#define H_STATUS_GOOD 0 143#define H_SEL_TIMEOUT 0x11 144#define H_OVER_UNDER_RUN 0x12 145#define H_UNEXP_BUS_FREE 0x13 146#define H_TARGET_PHASE_F 0x14 147#define H_INVALID_CCB_OP 0x16 148#define H_LINK_CCB_BAD 0x17 149#define H_BAD_TARGET_DIR 0x18 150#define H_DUPLICATE_CCB 0x19 151#define H_BAD_CCB_OR_SG 0x1A 152#define H_ABORT 0x0FF 153 154/* SCSI BUS Status byte codes */ 155#define SCSI_STAT_GOOD 0x0 /* Good status */ 156#define SCSI_STAT_CHECKCOND 0x02 /* SCSI Check Condition */ 157#define SCSI_STAT_CONDMET 0x04 /* Condition Met */ 158#define SCSI_STAT_BUSY 0x08 /* Target busy status */ 159#define SCSI_STAT_INTER 0x10 /* Intermediate status */ 160#define SCSI_STAT_INTERCONDMET 0x14 /* Intermediate condition met */ 161#define SCSI_STAT_RESCONFLICT 0x18 /* Reservation conflict */ 162#define SCSI_STAT_CMDTERM 0x22 /* Command Terminated */ 163#define SCSI_STAT_QUEUEFULL 0x28 /* Queue Full */ 164#define SCSI_STAT_UNEXP_BUS_F 0xFD /* Unexpect Bus Free */ 165#define SCSI_STAT_BUS_RST_DETECT 0xFE /* Scsi Bus Reset detected */ 166#define SCSI_STAT_SEL_TIMEOUT 0xFF /* Selection Time out */ 167 168/* Sync_Mode */ 169#define SYNC_WIDE_TAG_ATNT_DISABLE 0 170#define SYNC_NEGO_ENABLE BIT0 171#define SYNC_NEGO_DONE BIT1 172#define WIDE_NEGO_ENABLE BIT2 173#define WIDE_NEGO_DONE BIT3 174#define WIDE_NEGO_STATE BIT4 175#define EN_TAG_QUEUEING BIT5 176#define EN_ATN_STOP BIT6 177 178#define SYNC_NEGO_OFFSET 15 179 180/* SCSI MSG BYTE */ 181#define MSG_COMPLETE 0x00 182#define MSG_EXTENDED 0x01 183#define MSG_SAVE_PTR 0x02 184#define MSG_RESTORE_PTR 0x03 185#define MSG_DISCONNECT 0x04 186#define MSG_INITIATOR_ERROR 0x05 187#define MSG_ABORT 0x06 188#define MSG_REJECT_ 0x07 189#define MSG_NOP 0x08 190#define MSG_PARITY_ERROR 0x09 191#define MSG_LINK_CMD_COMPL 0x0A 192#define MSG_LINK_CMD_COMPL_FLG 0x0B 193#define MSG_BUS_RESET 0x0C 194#define MSG_ABORT_TAG 0x0D 195#define MSG_SIMPLE_QTAG 0x20 196#define MSG_HEAD_QTAG 0x21 197#define MSG_ORDER_QTAG 0x22 198#define MSG_IGNOREWIDE 0x23 199#define MSG_IDENTIFY 0x80 200#define MSG_HOST_ID 0xC0 201 202/* SCSI STATUS BYTE */ 203#define STATUS_GOOD 0x00 204#define CHECK_CONDITION_ 0x02 205#define STATUS_BUSY 0x08 206#define STATUS_INTERMEDIATE 0x10 207#define RESERVE_CONFLICT 0x18 208 209/* cmd->result */ 210#define STATUS_MASK_ 0xFF 211#define MSG_MASK 0xFF00 212#define RETURN_MASK 0xFF0000 213 214/************************************************************************/ 215/* */ 216/* Inquiry Data format */ 217/* */ 218/************************************************************************/ 219struct ScsiInqData 220{ /* INQ */ 221 u8 DevType; /* Periph Qualifier & Periph Dev Type */ 222 u8 RMB_TypeMod; /* rem media bit & Dev Type Modifier */ 223 u8 Vers; /* ISO, ECMA, & ANSI versions */ 224 u8 RDF; /* AEN, TRMIOP, & response data format */ 225 u8 AddLen; /* length of additional data */ 226 u8 Res1; /* reserved */ 227 u8 Res2; /* reserved */ 228 u8 Flags; /* RelADr, Wbus32, Wbus16, Sync, etc. */ 229 u8 VendorID[8]; /* Vendor Identification */ 230 u8 ProductID[16]; /* Product Identification */ 231 u8 ProductRev[4]; /* Product Revision */ 232}; 233 234 /* Inquiry byte 0 masks */ 235#define SCSI_DEVTYPE 0x1F /* Peripheral Device Type */ 236#define SCSI_PERIPHQUAL 0xE0 /* Peripheral Qualifier */ 237 /* Inquiry byte 1 mask */ 238#define SCSI_REMOVABLE_MEDIA 0x80 /* Removable Media bit (1=removable) */ 239 /* Peripheral Device Type definitions */ 240 /* See include/scsi/scsi.h */ 241#define TYPE_NODEV SCSI_DEVTYPE /* Unknown or no device type */ 242#ifndef TYPE_PRINTER /* */ 243# define TYPE_PRINTER 0x02 /* Printer device */ 244#endif /* */ 245#ifndef TYPE_COMM /* */ 246# define TYPE_COMM 0x09 /* Communications device */ 247#endif 248 249/************************************************************************/ 250/* */ 251/* Inquiry flag definitions (Inq data byte 7) */ 252/* */ 253/************************************************************************/ 254#define SCSI_INQ_RELADR 0x80 /* device supports relative addressing */ 255#define SCSI_INQ_WBUS32 0x40 /* device supports 32 bit data xfers */ 256#define SCSI_INQ_WBUS16 0x20 /* device supports 16 bit data xfers */ 257#define SCSI_INQ_SYNC 0x10 /* device supports synchronous xfer */ 258#define SCSI_INQ_LINKED 0x08 /* device supports linked commands */ 259#define SCSI_INQ_CMDQUEUE 0x02 /* device supports command queueing */ 260#define SCSI_INQ_SFTRE 0x01 /* device supports soft resets */ 261 262#define ENABLE_CE 1 263#define DISABLE_CE 0 264#define EEPROM_READ 0x80 265 266/************************************************************************/ 267/* */ 268/* The PCI configuration register offset for TRM_S1040 */ 269/* */ 270/************************************************************************/ 271#define TRM_S1040_ID 0x00 /* Vendor and Device ID */ 272#define TRM_S1040_COMMAND 0x04 /* PCI command register */ 273#define TRM_S1040_IOBASE 0x10 /* I/O Space base address */ 274#define TRM_S1040_ROMBASE 0x30 /* Expansion ROM Base Address */ 275#define TRM_S1040_INTLINE 0x3C /* Interrupt line */ 276 277/************************************************************************/ 278/* */ 279/* The SCSI register offset for TRM_S1040 */ 280/* */ 281/************************************************************************/ 282#define TRM_S1040_SCSI_STATUS 0x80 /* SCSI Status (R) */ 283#define COMMANDPHASEDONE 0x2000 /* SCSI command phase done */ 284#define SCSIXFERDONE 0x0800 /* SCSI SCSI transfer done */ 285#define SCSIXFERCNT_2_ZERO 0x0100 /* SCSI SCSI transfer count to zero */ 286#define SCSIINTERRUPT 0x0080 /* SCSI interrupt pending */ 287#define COMMANDABORT 0x0040 /* SCSI command abort */ 288#define SEQUENCERACTIVE 0x0020 /* SCSI sequencer active */ 289#define PHASEMISMATCH 0x0010 /* SCSI phase mismatch */ 290#define PARITYERROR 0x0008 /* SCSI parity error */ 291 292#define PHASEMASK 0x0007 /* Phase MSG/CD/IO */ 293#define PH_DATA_OUT 0x00 /* Data out phase */ 294#define PH_DATA_IN 0x01 /* Data in phase */ 295#define PH_COMMAND 0x02 /* Command phase */ 296#define PH_STATUS 0x03 /* Status phase */ 297#define PH_BUS_FREE 0x05 /* Invalid phase used as bus free */ 298#define PH_MSG_OUT 0x06 /* Message out phase */ 299#define PH_MSG_IN 0x07 /* Message in phase */ 300 301#define TRM_S1040_SCSI_CONTROL 0x80 /* SCSI Control (W) */ 302#define DO_CLRATN 0x0400 /* Clear ATN */ 303#define DO_SETATN 0x0200 /* Set ATN */ 304#define DO_CMDABORT 0x0100 /* Abort SCSI command */ 305#define DO_RSTMODULE 0x0010 /* Reset SCSI chip */ 306#define DO_RSTSCSI 0x0008 /* Reset SCSI bus */ 307#define DO_CLRFIFO 0x0004 /* Clear SCSI transfer FIFO */ 308#define DO_DATALATCH 0x0002 /* Enable SCSI bus data input (latched) */ 309/* #define DO_DATALATCH 0x0000 */ /* KG: DISable SCSI bus data latch */ 310#define DO_HWRESELECT 0x0001 /* Enable hardware reselection */ 311 312#define TRM_S1040_SCSI_FIFOCNT 0x82 /* SCSI FIFO Counter 5bits(R) */ 313#define TRM_S1040_SCSI_SIGNAL 0x83 /* SCSI low level signal (R/W) */ 314 315#define TRM_S1040_SCSI_INTSTATUS 0x84 /* SCSI Interrupt Status (R) */ 316#define INT_SCAM 0x80 /* SCAM selection interrupt */ 317#define INT_SELECT 0x40 /* Selection interrupt */ 318#define INT_SELTIMEOUT 0x20 /* Selection timeout interrupt */ 319#define INT_DISCONNECT 0x10 /* Bus disconnected interrupt */ 320#define INT_RESELECTED 0x08 /* Reselected interrupt */ 321#define INT_SCSIRESET 0x04 /* SCSI reset detected interrupt */ 322#define INT_BUSSERVICE 0x02 /* Bus service interrupt */ 323#define INT_CMDDONE 0x01 /* SCSI command done interrupt */ 324 325#define TRM_S1040_SCSI_OFFSET 0x84 /* SCSI Offset Count (W) */ 326 327/************************************************************************/ 328/* */ 329/* Bit Name Definition */ 330/* --------- ------------- ---------------------------- */ 331/* 07-05 0 RSVD Reversed. Always 0. */ 332/* 04 0 OFFSET4 Reversed for LVDS. Always 0. */ 333/* 03-00 0 OFFSET[03:00] Offset number from 0 to 15 */ 334/* */ 335/************************************************************************/ 336 337#define TRM_S1040_SCSI_SYNC 0x85 /* SCSI Synchronous Control (R/W) */ 338#define LVDS_SYNC 0x20 /* Enable LVDS synchronous */ 339#define WIDE_SYNC 0x10 /* Enable WIDE synchronous */ 340#define ALT_SYNC 0x08 /* Enable Fast-20 alternate synchronous */ 341 342/************************************************************************/ 343/* */ 344/* SYNCM 7 6 5 4 3 2 1 0 */ 345/* Name RSVD RSVD LVDS WIDE ALTPERD PERIOD2 PERIOD1 PERIOD0 */ 346/* Default 0 0 0 0 0 0 0 0 */ 347/* */ 348/* Bit Name Definition */ 349/* --------- ------------- --------------------------- */ 350/* 07-06 0 RSVD Reversed. Always read 0 */ 351/* 05 0 LVDS Reversed. Always read 0 */ 352/* 04 0 WIDE/WSCSI Enable wide (16-bits) SCSI */ 353/* transfer. */ 354/* 03 0 ALTPERD/ALTPD Alternate (Sync./Period) mode. */ 355/* */ 356/* @@ When this bit is set, */ 357/* the synchronous period bits 2:0 */ 358/* in the Synchronous Mode register */ 359/* are used to transfer data */ 360/* at the Fast-20 rate. */ 361/* @@ When this bit is unset, */ 362/* the synchronous period bits 2:0 */ 363/* in the Synchronous Mode Register */ 364/* are used to transfer data */ 365/* at the Fast-10 rate (or Fast-40 w/ LVDS). */ 366/* */ 367/* 02-00 0 PERIOD[2:0]/ Synchronous SCSI Transfer Rate. */ 368/* SXPD[02:00] These 3 bits specify */ 369/* the Synchronous SCSI Transfer */ 370/* Rate for Fast-20 and Fast-10. */ 371/* These bits are also reset */ 372/* by a SCSI Bus reset. */ 373/* */ 374/* For Fast-10 bit ALTPD = 0 and LVDS = 0 */ 375/* and bit2,bit1,bit0 is defined as follows : */ 376/* */ 377/* 000 100ns, 10.0 MHz */ 378/* 001 150ns, 6.6 MHz */ 379/* 010 200ns, 5.0 MHz */ 380/* 011 250ns, 4.0 MHz */ 381/* 100 300ns, 3.3 MHz */ 382/* 101 350ns, 2.8 MHz */ 383/* 110 400ns, 2.5 MHz */ 384/* 111 450ns, 2.2 MHz */ 385/* */ 386/* For Fast-20 bit ALTPD = 1 and LVDS = 0 */ 387/* and bit2,bit1,bit0 is defined as follows : */ 388/* */ 389/* 000 50ns, 20.0 MHz */ 390/* 001 75ns, 13.3 MHz */ 391/* 010 100ns, 10.0 MHz */ 392/* 011 125ns, 8.0 MHz */ 393/* 100 150ns, 6.6 MHz */ 394/* 101 175ns, 5.7 MHz */ 395/* 110 200ns, 5.0 MHz */ 396/* 111 250ns, 4.0 MHz KG: Maybe 225ns, 4.4 MHz */ 397/* */ 398/* For Fast-40 bit ALTPD = 0 and LVDS = 1 */ 399/* and bit2,bit1,bit0 is defined as follows : */ 400/* */ 401/* 000 25ns, 40.0 MHz */ 402/* 001 50ns, 20.0 MHz */ 403/* 010 75ns, 13.3 MHz */ 404/* 011 100ns, 10.0 MHz */ 405/* 100 125ns, 8.0 MHz */ 406/* 101 150ns, 6.6 MHz */ 407/* 110 175ns, 5.7 MHz */ 408/* 111 200ns, 5.0 MHz */ 409/* */ 410/************************************************************************/ 411 412#define TRM_S1040_SCSI_TARGETID 0x86 /* SCSI Target ID (R/W) */ 413#define TRM_S1040_SCSI_IDMSG 0x87 /* SCSI Identify Message (R) */ 414#define TRM_S1040_SCSI_HOSTID 0x87 /* SCSI Host ID (W) */ 415#define TRM_S1040_SCSI_COUNTER 0x88 /* SCSI Transfer Counter 24bits(R/W) */ 416 417#define TRM_S1040_SCSI_INTEN 0x8C /* SCSI Interrupt Enable (R/W) */ 418#define EN_SCAM 0x80 /* Enable SCAM selection interrupt */ 419#define EN_SELECT 0x40 /* Enable selection interrupt */ 420#define EN_SELTIMEOUT 0x20 /* Enable selection timeout interrupt */ 421#define EN_DISCONNECT 0x10 /* Enable bus disconnected interrupt */ 422#define EN_RESELECTED 0x08 /* Enable reselected interrupt */ 423#define EN_SCSIRESET 0x04 /* Enable SCSI reset detected interrupt */ 424#define EN_BUSSERVICE 0x02 /* Enable bus service interrupt */ 425#define EN_CMDDONE 0x01 /* Enable SCSI command done interrupt */ 426 427#define TRM_S1040_SCSI_CONFIG0 0x8D /* SCSI Configuration 0 (R/W) */ 428#define PHASELATCH 0x40 /* Enable phase latch */ 429#define INITIATOR 0x20 /* Enable initiator mode */ 430#define PARITYCHECK 0x10 /* Enable parity check */ 431#define BLOCKRST 0x01 /* Disable SCSI reset1 */ 432 433#define TRM_S1040_SCSI_CONFIG1 0x8E /* SCSI Configuration 1 (R/W) */ 434#define ACTIVE_NEGPLUS 0x10 /* Enhance active negation */ 435#define FILTER_DISABLE 0x08 /* Disable SCSI data filter */ 436#define FAST_FILTER 0x04 /* ? */ 437#define ACTIVE_NEG 0x02 /* Enable active negation */ 438 439#define TRM_S1040_SCSI_CONFIG2 0x8F /* SCSI Configuration 2 (R/W) */ 440#define CFG2_WIDEFIFO 0x02 /* */ 441 442#define TRM_S1040_SCSI_COMMAND 0x90 /* SCSI Command (R/W) */ 443#define SCMD_COMP 0x12 /* Command complete */ 444#define SCMD_SEL_ATN 0x60 /* Selection with ATN */ 445#define SCMD_SEL_ATN3 0x64 /* Selection with ATN3 */ 446#define SCMD_SEL_ATNSTOP 0xB8 /* Selection with ATN and Stop */ 447#define SCMD_FIFO_OUT 0xC0 /* SCSI FIFO transfer out */ 448#define SCMD_DMA_OUT 0xC1 /* SCSI DMA transfer out */ 449#define SCMD_FIFO_IN 0xC2 /* SCSI FIFO transfer in */ 450#define SCMD_DMA_IN 0xC3 /* SCSI DMA transfer in */ 451#define SCMD_MSGACCEPT 0xD8 /* Message accept */ 452 453/************************************************************************/ 454/* */ 455/* Code Command Description */ 456/* ---- ---------------------------------------- */ 457/* 02 Enable reselection with FIFO */ 458/* 40 Select without ATN with FIFO */ 459/* 60 Select with ATN with FIFO */ 460/* 64 Select with ATN3 with FIFO */ 461/* A0 Select with ATN and stop with FIFO */ 462/* C0 Transfer information out with FIFO */ 463/* C1 Transfer information out with DMA */ 464/* C2 Transfer information in with FIFO */ 465/* C3 Transfer information in with DMA */ 466/* 12 Initiator command complete with FIFO */ 467/* 50 Initiator transfer information out sequence without ATN */ 468/* with FIFO */ 469/* 70 Initiator transfer information out sequence with ATN */ 470/* with FIFO */ 471/* 74 Initiator transfer information out sequence with ATN3 */ 472/* with FIFO */ 473/* 52 Initiator transfer information in sequence without ATN */ 474/* with FIFO */ 475/* 72 Initiator transfer information in sequence with ATN */ 476/* with FIFO */ 477/* 76 Initiator transfer information in sequence with ATN3 */ 478/* with FIFO */ 479/* 90 Initiator transfer information out command complete */ 480/* with FIFO */ 481/* 92 Initiator transfer information in command complete */ 482/* with FIFO */ 483/* D2 Enable selection */ 484/* 08 Reselection */ 485/* 48 Disconnect command with FIFO */ 486/* 88 Terminate command with FIFO */ 487/* C8 Target command complete with FIFO */ 488/* 18 SCAM Arbitration/ Selection */ 489/* 5A Enable reselection */ 490/* 98 Select without ATN with FIFO */ 491/* B8 Select with ATN with FIFO */ 492/* D8 Message Accepted */ 493/* 58 NOP */ 494/* */ 495/************************************************************************/ 496 497#define TRM_S1040_SCSI_TIMEOUT 0x91 /* SCSI Time Out Value (R/W) */ 498#define TRM_S1040_SCSI_FIFO 0x98 /* SCSI FIFO (R/W) */ 499 500#define TRM_S1040_SCSI_TCR0 0x9C /* SCSI Target Control 0 (R/W) */ 501#define TCR0_WIDE_NEGO_DONE 0x8000 /* Wide nego done */ 502#define TCR0_SYNC_NEGO_DONE 0x4000 /* Synchronous nego done */ 503#define TCR0_ENABLE_LVDS 0x2000 /* Enable LVDS synchronous */ 504#define TCR0_ENABLE_WIDE 0x1000 /* Enable WIDE synchronous */ 505#define TCR0_ENABLE_ALT 0x0800 /* Enable alternate synchronous */ 506#define TCR0_PERIOD_MASK 0x0700 /* Transfer rate */ 507 508#define TCR0_DO_WIDE_NEGO 0x0080 /* Do wide NEGO */ 509#define TCR0_DO_SYNC_NEGO 0x0040 /* Do sync NEGO */ 510#define TCR0_DISCONNECT_EN 0x0020 /* Disconnection enable */ 511#define TCR0_OFFSET_MASK 0x001F /* Offset number */ 512 513#define TRM_S1040_SCSI_TCR1 0x9E /* SCSI Target Control 1 (R/W) */ 514#define MAXTAG_MASK 0x7F00 /* Maximum tags (127) */ 515#define NON_TAG_BUSY 0x0080 /* Non tag command active */ 516#define ACTTAG_MASK 0x007F /* Active tags */ 517 518/************************************************************************/ 519/* */ 520/* The DMA register offset for TRM_S1040 */ 521/* */ 522/************************************************************************/ 523#define TRM_S1040_DMA_COMMAND 0xA0 /* DMA Command (R/W) */ 524#define DMACMD_SG 0x02 /* Enable HW S/G support */ 525#define DMACMD_DIR 0x01 /* 1 = read from SCSI write to Host */ 526#define XFERDATAIN_SG 0x0103 /* Transfer data in w/ SG */ 527#define XFERDATAOUT_SG 0x0102 /* Transfer data out w/ SG */ 528#define XFERDATAIN 0x0101 /* Transfer data in w/o SG */ 529#define XFERDATAOUT 0x0100 /* Transfer data out w/o SG */ 530 531#define TRM_S1040_DMA_FIFOCNT 0xA1 /* DMA FIFO Counter (R) */ 532 533#define TRM_S1040_DMA_CONTROL 0xA1 /* DMA Control (W) */ 534#define DMARESETMODULE 0x10 /* Reset PCI/DMA module */ 535#define STOPDMAXFER 0x08 /* Stop DMA transfer */ 536#define ABORTXFER 0x04 /* Abort DMA transfer */ 537#define CLRXFIFO 0x02 /* Clear DMA transfer FIFO */ 538#define STARTDMAXFER 0x01 /* Start DMA transfer */ 539 540#define TRM_S1040_DMA_FIFOSTAT 0xA2 /* DMA FIFO Status (R) */ 541 542#define TRM_S1040_DMA_STATUS 0xA3 /* DMA Interrupt Status (R/W) */ 543#define XFERPENDING 0x80 /* Transfer pending */ 544#define SCSIBUSY 0x40 /* SCSI busy */ 545#define GLOBALINT 0x20 /* DMA_INTEN bit 0-4 set */ 546#define FORCEDMACOMP 0x10 /* Force DMA transfer complete */ 547#define DMAXFERERROR 0x08 /* DMA transfer error */ 548#define DMAXFERABORT 0x04 /* DMA transfer abort */ 549#define DMAXFERCOMP 0x02 /* Bus Master XFER Complete status */ 550#define SCSICOMP 0x01 /* SCSI complete interrupt */ 551 552#define TRM_S1040_DMA_INTEN 0xA4 /* DMA Interrupt Enable (R/W) */ 553#define EN_FORCEDMACOMP 0x10 /* Force DMA transfer complete */ 554#define EN_DMAXFERERROR 0x08 /* DMA transfer error */ 555#define EN_DMAXFERABORT 0x04 /* DMA transfer abort */ 556#define EN_DMAXFERCOMP 0x02 /* Bus Master XFER Complete status */ 557#define EN_SCSIINTR 0x01 /* Enable SCSI complete interrupt */ 558 559#define TRM_S1040_DMA_CONFIG 0xA6 /* DMA Configuration (R/W) */ 560#define DMA_ENHANCE 0x8000 /* Enable DMA enhance feature (SG?) */ 561#define DMA_PCI_DUAL_ADDR 0x4000 /* */ 562#define DMA_CFG_RES 0x2000 /* Always 1 */ 563#define DMA_AUTO_CLR_FIFO 0x1000 /* DISable DMA auto clear FIFO */ 564#define DMA_MEM_MULTI_READ 0x0800 /* */ 565#define DMA_MEM_WRITE_INVAL 0x0400 /* Memory write and invalidate */ 566#define DMA_FIFO_CTRL 0x0300 /* Control FIFO operation with DMA */ 567#define DMA_FIFO_HALF_HALF 0x0200 /* Keep half filled on both read/write */ 568 569#define TRM_S1040_DMA_XCNT 0xA8 /* DMA Transfer Counter (R/W), 24bits */ 570#define TRM_S1040_DMA_CXCNT 0xAC /* DMA Current Transfer Counter (R) */ 571#define TRM_S1040_DMA_XLOWADDR 0xB0 /* DMA Transfer Physical Low Address */ 572#define TRM_S1040_DMA_XHIGHADDR 0xB4 /* DMA Transfer Physical High Address */ 573 574/************************************************************************/ 575/* */ 576/* The general register offset for TRM_S1040 */ 577/* */ 578/************************************************************************/ 579#define TRM_S1040_GEN_CONTROL 0xD4 /* Global Control */ 580#define CTRL_LED 0x80 /* Control onboard LED */ 581#define EN_EEPROM 0x10 /* Enable EEPROM programming */ 582#define DIS_TERM 0x08 /* Disable onboard termination */ 583#define AUTOTERM 0x04 /* Enable Auto SCSI terminator */ 584#define LOW8TERM 0x02 /* Enable Lower 8 bit SCSI terminator */ 585#define UP8TERM 0x01 /* Enable Upper 8 bit SCSI terminator */ 586 587#define TRM_S1040_GEN_STATUS 0xD5 /* Global Status */ 588#define GTIMEOUT 0x80 /* Global timer reach 0 */ 589#define EXT68HIGH 0x40 /* Higher 8 bit connected externally */ 590#define INT68HIGH 0x20 /* Higher 8 bit connected internally */ 591#define CON5068 0x10 /* External 50/68 pin connected (low) */ 592#define CON68 0x08 /* Internal 68 pin connected (low) */ 593#define CON50 0x04 /* Internal 50 pin connected (low!) */ 594#define WIDESCSI 0x02 /* Wide SCSI card */ 595#define STATUS_LOAD_DEFAULT 0x01 /* */ 596 597#define TRM_S1040_GEN_NVRAM 0xD6 /* Serial NON-VOLATILE RAM port */ 598#define NVR_BITOUT 0x08 /* Serial data out */ 599#define NVR_BITIN 0x04 /* Serial data in */ 600#define NVR_CLOCK 0x02 /* Serial clock */ 601#define NVR_SELECT 0x01 /* Serial select */ 602 603#define TRM_S1040_GEN_EDATA 0xD7 /* Parallel EEPROM data port */ 604#define TRM_S1040_GEN_EADDRESS 0xD8 /* Parallel EEPROM address */ 605#define TRM_S1040_GEN_TIMER 0xDB /* Global timer */ 606 607/************************************************************************/ 608/* */ 609/* NvmTarCfg0: Target configuration byte 0 :..pDCB->DevMode */ 610/* */ 611/************************************************************************/ 612#define NTC_DO_WIDE_NEGO 0x20 /* Wide negotiate */ 613#define NTC_DO_TAG_QUEUEING 0x10 /* Enable SCSI tag queuing */ 614#define NTC_DO_SEND_START 0x08 /* Send start command SPINUP */ 615#define NTC_DO_DISCONNECT 0x04 /* Enable SCSI disconnect */ 616#define NTC_DO_SYNC_NEGO 0x02 /* Sync negotiation */ 617#define NTC_DO_PARITY_CHK 0x01 /* (it sould define at NAC) */ 618 /* Parity check enable */ 619 620/************************************************************************/ 621/* */ 622/* Nvram Initiater bits definition */ 623/* */ 624/************************************************************************/ 625 626/************************************************************************/ 627/* */ 628/* Nvram Adapter Cfg bits definition */ 629/* */ 630/************************************************************************/ 631#define NAC_SCANLUN 0x20 /* Include LUN as BIOS device */ 632#define NAC_POWERON_SCSI_RESET 0x04 /* Power on reset enable */ 633#define NAC_GREATER_1G 0x02 /* > 1G support enable */ 634#define NAC_GT2DRIVES 0x01 /* Support more than 2 drives */ 635/* #define NAC_DO_PARITY_CHK 0x08 */ /* Parity check enable */ 636 637#endif 638