1/* 2 * QNAP TS-109/TS-209 Board Setup 3 * 4 * Maintainer: Byron Bradley <byron.bbradley@gmail.com> 5 * 6 * This program is free software; you can redistribute it and/or 7 * modify it under the terms of the GNU General Public License 8 * as published by the Free Software Foundation; either version 9 * 2 of the License, or (at your option) any later version. 10 */ 11 12#include <linux/kernel.h> 13#include <linux/init.h> 14#include <linux/platform_device.h> 15#include <linux/pci.h> 16#include <linux/irq.h> 17#include <linux/mtd/physmap.h> 18#include <linux/mtd/nand.h> 19#include <linux/mv643xx_eth.h> 20#include <linux/gpio_keys.h> 21#include <linux/input.h> 22#include <linux/i2c.h> 23#include <linux/serial_reg.h> 24#include <linux/ata_platform.h> 25#include <asm/mach-types.h> 26#include <asm/gpio.h> 27#include <asm/mach/arch.h> 28#include <asm/mach/pci.h> 29#include <mach/orion5x.h> 30#include "common.h" 31#include "mpp.h" 32#include "tsx09-common.h" 33 34#define QNAP_TS209_NOR_BOOT_BASE 0xf4000000 35#define QNAP_TS209_NOR_BOOT_SIZE SZ_8M 36 37/**************************************************************************** 38 * 8MiB NOR flash. The struct mtd_partition is not in the same order as the 39 * partitions on the device because we want to keep compatability with 40 * existing QNAP firmware. 41 * 42 * Layout as used by QNAP: 43 * [2] 0x00000000-0x00200000 : "Kernel" 44 * [3] 0x00200000-0x00600000 : "RootFS1" 45 * [4] 0x00600000-0x00700000 : "RootFS2" 46 * [6] 0x00700000-0x00760000 : "NAS Config" (read-only) 47 * [5] 0x00760000-0x00780000 : "U-Boot Config" 48 * [1] 0x00780000-0x00800000 : "U-Boot" (read-only) 49 ***************************************************************************/ 50static struct mtd_partition qnap_ts209_partitions[] = { 51 { 52 .name = "U-Boot", 53 .size = 0x00080000, 54 .offset = 0x00780000, 55 .mask_flags = MTD_WRITEABLE, 56 }, { 57 .name = "Kernel", 58 .size = 0x00200000, 59 .offset = 0, 60 }, { 61 .name = "RootFS1", 62 .size = 0x00400000, 63 .offset = 0x00200000, 64 }, { 65 .name = "RootFS2", 66 .size = 0x00100000, 67 .offset = 0x00600000, 68 }, { 69 .name = "U-Boot Config", 70 .size = 0x00020000, 71 .offset = 0x00760000, 72 }, { 73 .name = "NAS Config", 74 .size = 0x00060000, 75 .offset = 0x00700000, 76 .mask_flags = MTD_WRITEABLE, 77 }, 78}; 79 80static struct physmap_flash_data qnap_ts209_nor_flash_data = { 81 .width = 1, 82 .parts = qnap_ts209_partitions, 83 .nr_parts = ARRAY_SIZE(qnap_ts209_partitions) 84}; 85 86static struct resource qnap_ts209_nor_flash_resource = { 87 .flags = IORESOURCE_MEM, 88 .start = QNAP_TS209_NOR_BOOT_BASE, 89 .end = QNAP_TS209_NOR_BOOT_BASE + QNAP_TS209_NOR_BOOT_SIZE - 1, 90}; 91 92static struct platform_device qnap_ts209_nor_flash = { 93 .name = "physmap-flash", 94 .id = 0, 95 .dev = { 96 .platform_data = &qnap_ts209_nor_flash_data, 97 }, 98 .resource = &qnap_ts209_nor_flash_resource, 99 .num_resources = 1, 100}; 101 102/***************************************************************************** 103 * PCI 104 ****************************************************************************/ 105 106#define QNAP_TS209_PCI_SLOT0_OFFS 7 107#define QNAP_TS209_PCI_SLOT0_IRQ_PIN 6 108#define QNAP_TS209_PCI_SLOT1_IRQ_PIN 7 109 110void __init qnap_ts209_pci_preinit(void) 111{ 112 int pin; 113 114 /* 115 * Configure PCI GPIO IRQ pins 116 */ 117 pin = QNAP_TS209_PCI_SLOT0_IRQ_PIN; 118 if (gpio_request(pin, "PCI Int1") == 0) { 119 if (gpio_direction_input(pin) == 0) { 120 set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW); 121 } else { 122 printk(KERN_ERR "qnap_ts209_pci_preinit failed to " 123 "set_irq_type pin %d\n", pin); 124 gpio_free(pin); 125 } 126 } else { 127 printk(KERN_ERR "qnap_ts209_pci_preinit failed to gpio_request " 128 "%d\n", pin); 129 } 130 131 pin = QNAP_TS209_PCI_SLOT1_IRQ_PIN; 132 if (gpio_request(pin, "PCI Int2") == 0) { 133 if (gpio_direction_input(pin) == 0) { 134 set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW); 135 } else { 136 printk(KERN_ERR "qnap_ts209_pci_preinit failed " 137 "to set_irq_type pin %d\n", pin); 138 gpio_free(pin); 139 } 140 } else { 141 printk(KERN_ERR "qnap_ts209_pci_preinit failed to gpio_request " 142 "%d\n", pin); 143 } 144} 145 146static int __init qnap_ts209_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) 147{ 148 int irq; 149 150 /* 151 * Check for devices with hard-wired IRQs. 152 */ 153 irq = orion5x_pci_map_irq(dev, slot, pin); 154 if (irq != -1) 155 return irq; 156 157 /* 158 * PCI IRQs are connected via GPIOs. 159 */ 160 switch (slot - QNAP_TS209_PCI_SLOT0_OFFS) { 161 case 0: 162 return gpio_to_irq(QNAP_TS209_PCI_SLOT0_IRQ_PIN); 163 case 1: 164 return gpio_to_irq(QNAP_TS209_PCI_SLOT1_IRQ_PIN); 165 default: 166 return -1; 167 } 168} 169 170static struct hw_pci qnap_ts209_pci __initdata = { 171 .nr_controllers = 2, 172 .preinit = qnap_ts209_pci_preinit, 173 .swizzle = pci_std_swizzle, 174 .setup = orion5x_pci_sys_setup, 175 .scan = orion5x_pci_sys_scan_bus, 176 .map_irq = qnap_ts209_pci_map_irq, 177}; 178 179static int __init qnap_ts209_pci_init(void) 180{ 181 if (machine_is_ts_x09()) 182 pci_common_init(&qnap_ts209_pci); 183 184 return 0; 185} 186 187subsys_initcall(qnap_ts209_pci_init); 188 189/***************************************************************************** 190 * RTC S35390A on I2C bus 191 ****************************************************************************/ 192 193#define TS209_RTC_GPIO 3 194 195static struct i2c_board_info __initdata qnap_ts209_i2c_rtc = { 196 I2C_BOARD_INFO("s35390a", 0x30), 197 .irq = 0, 198}; 199 200/**************************************************************************** 201 * GPIO Attached Keys 202 * Power button is attached to the PIC microcontroller 203 ****************************************************************************/ 204 205#define QNAP_TS209_GPIO_KEY_MEDIA 1 206#define QNAP_TS209_GPIO_KEY_RESET 2 207 208static struct gpio_keys_button qnap_ts209_buttons[] = { 209 { 210 .code = KEY_COPY, 211 .gpio = QNAP_TS209_GPIO_KEY_MEDIA, 212 .desc = "USB Copy Button", 213 .active_low = 1, 214 }, { 215 .code = KEY_RESTART, 216 .gpio = QNAP_TS209_GPIO_KEY_RESET, 217 .desc = "Reset Button", 218 .active_low = 1, 219 }, 220}; 221 222static struct gpio_keys_platform_data qnap_ts209_button_data = { 223 .buttons = qnap_ts209_buttons, 224 .nbuttons = ARRAY_SIZE(qnap_ts209_buttons), 225}; 226 227static struct platform_device qnap_ts209_button_device = { 228 .name = "gpio-keys", 229 .id = -1, 230 .num_resources = 0, 231 .dev = { 232 .platform_data = &qnap_ts209_button_data, 233 }, 234}; 235 236/***************************************************************************** 237 * SATA 238 ****************************************************************************/ 239static struct mv_sata_platform_data qnap_ts209_sata_data = { 240 .n_ports = 2, 241}; 242 243/***************************************************************************** 244 245 * General Setup 246 ****************************************************************************/ 247static struct orion5x_mpp_mode ts209_mpp_modes[] __initdata = { 248 { 0, MPP_UNUSED }, 249 { 1, MPP_GPIO }, /* USB copy button */ 250 { 2, MPP_GPIO }, /* Load defaults button */ 251 { 3, MPP_GPIO }, /* GPIO RTC */ 252 { 4, MPP_UNUSED }, 253 { 5, MPP_UNUSED }, 254 { 6, MPP_GPIO }, /* PCI Int A */ 255 { 7, MPP_GPIO }, /* PCI Int B */ 256 { 8, MPP_UNUSED }, 257 { 9, MPP_UNUSED }, 258 { 10, MPP_UNUSED }, 259 { 11, MPP_UNUSED }, 260 { 12, MPP_SATA_LED }, /* SATA 0 presence */ 261 { 13, MPP_SATA_LED }, /* SATA 1 presence */ 262 { 14, MPP_SATA_LED }, /* SATA 0 active */ 263 { 15, MPP_SATA_LED }, /* SATA 1 active */ 264 { 16, MPP_UART }, /* UART1 RXD */ 265 { 17, MPP_UART }, /* UART1 TXD */ 266 { 18, MPP_GPIO }, /* SW_RST */ 267 { 19, MPP_UNUSED }, 268 { -1 }, 269}; 270 271static void __init qnap_ts209_init(void) 272{ 273 /* 274 * Setup basic Orion functions. Need to be called early. 275 */ 276 orion5x_init(); 277 278 orion5x_mpp_conf(ts209_mpp_modes); 279 280 /* 281 * MPP[20] PCI clock 0 282 * MPP[21] PCI clock 1 283 * MPP[22] USB 0 over current 284 * MPP[23-25] Reserved 285 */ 286 287 /* 288 * Configure peripherals. 289 */ 290 orion5x_setup_dev_boot_win(QNAP_TS209_NOR_BOOT_BASE, 291 QNAP_TS209_NOR_BOOT_SIZE); 292 platform_device_register(&qnap_ts209_nor_flash); 293 294 orion5x_ehci0_init(); 295 orion5x_ehci1_init(); 296 qnap_tsx09_find_mac_addr(QNAP_TS209_NOR_BOOT_BASE + 297 qnap_ts209_partitions[5].offset, 298 qnap_ts209_partitions[5].size); 299 orion5x_eth_init(&qnap_tsx09_eth_data); 300 orion5x_i2c_init(); 301 orion5x_sata_init(&qnap_ts209_sata_data); 302 orion5x_uart0_init(); 303 orion5x_uart1_init(); 304 orion5x_xor_init(); 305 306 platform_device_register(&qnap_ts209_button_device); 307 308 /* Get RTC IRQ and register the chip */ 309 if (gpio_request(TS209_RTC_GPIO, "rtc") == 0) { 310 if (gpio_direction_input(TS209_RTC_GPIO) == 0) 311 qnap_ts209_i2c_rtc.irq = gpio_to_irq(TS209_RTC_GPIO); 312 else 313 gpio_free(TS209_RTC_GPIO); 314 } 315 if (qnap_ts209_i2c_rtc.irq == 0) 316 pr_warning("qnap_ts209_init: failed to get RTC IRQ\n"); 317 i2c_register_board_info(0, &qnap_ts209_i2c_rtc, 1); 318 319 /* register tsx09 specific power-off method */ 320 pm_power_off = qnap_tsx09_power_off; 321} 322 323MACHINE_START(TS209, "QNAP TS-109/TS-209") 324 /* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */ 325 .phys_io = ORION5X_REGS_PHYS_BASE, 326 .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, 327 .boot_params = 0x00000100, 328 .init_machine = qnap_ts209_init, 329 .map_io = orion5x_map_io, 330 .init_irq = orion5x_init_irq, 331 .timer = &orion5x_timer, 332 .fixup = tag_fixup_mem32, 333MACHINE_END 334