1/* $NetBSD: lemacreg.h,v 1.6 2021/07/24 21:31:37 andvar Exp $ */ 2 3/* 4 * Copyright (c) 1994, 1995, 1997 Matt Thomas <matt@3am-software.com> 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. The name of the author may not be used to endorse or promote products 13 * derived from this software without specific prior written permission 14 * 15 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 16 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 17 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 18 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 19 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 20 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 21 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 22 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 23 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 24 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 25 */ 26#ifndef _LEMAC_H_ 27#define _LEMAC_H_ 28 29#define LEMAC_IOBASE_LOW 0x200 30#define LEMAC_IOBASE_HIGH 0x400 31 32/* 33 * This is list of registers used on a DEC EtherWORKS III card. 34 * Each board occupies a 32 byte register space. This can be 35 * in either EISA or ISA space. Currently we only support ISA 36 * space. 37 */ 38 39#define LEMAC_REG_CS 0x00 /* Control and Status */ 40#define LEMAC_REG_CTL 0x01 /* Control */ 41#define LEMAC_REG_IC 0x02 /* Interrupt Control */ 42#define LEMAC_REG_TS 0x03 /* Transmit Status */ 43#define LEMAC_REG_RSVD1 0x04 /* Reserved (not used) */ 44#define LEMAC_REG_RSVD2 0x05 /* Reserved (not used) */ 45#define LEMAC_REG_FMQ 0x06 /* Free Memory Queue */ 46#define LEMAC_REG_FMC 0x07 /* Free Memory Queue Count */ 47#define LEMAC_REG_RQ 0x08 /* Receive Queue */ 48#define LEMAC_REG_RQC 0x09 /* Receive Queue Count */ 49#define LEMAC_REG_TQ 0x0A /* Transmit Queue */ 50#define LEMAC_REG_TQC 0x0B /* Transmit Queue Count */ 51#define LEMAC_REG_TDQ 0x0C /* Transmit Done Queue */ 52#define LEMAC_REG_TDC 0x0D /* Transmit Done Queue Count */ 53#define LEMAC_REG_PI1 0x0E /* Page Index #1 */ 54#define LEMAC_REG_PI2 0x0F /* Page Index #2 */ 55#define LEMAC_REG_DAT 0x10 /* Data */ 56#define LEMAC_REG_IOP 0x11 /* I/O Page */ 57#define LEMAC_REG_IOB 0x12 /* I/O Base */ 58#define LEMAC_REG_MPN 0x13 /* Memory Page */ 59#define LEMAC_REG_MBR 0x14 /* Memory Base */ 60#define LEMAC_REG_APD 0x15 /* Address PROM */ 61#define LEMAC_REG_EE1 0x16 /* EEPROM Data #1 */ 62#define LEMAC_REG_EE2 0x17 /* EEPROM Data #2 */ 63#define LEMAC_REG_PA0 0x18 /* Physical Address (Byte 0) */ 64#define LEMAC_REG_PA1 0x19 /* Physical Address (Byte 1) */ 65#define LEMAC_REG_PA2 0x1A /* Physical Address (Byte 2) */ 66#define LEMAC_REG_PA3 0x1B /* Physical Address (Byte 3) */ 67#define LEMAC_REG_PA4 0x1C /* Physical Address (Byte 4) */ 68#define LEMAC_REG_PA5 0x1D /* Physical Address (Byte 5) */ 69#define LEMAC_REG_CNF 0x1E /* Configuration Management */ 70#define LEMAC_IOSIZE 0x20 /* LEMAC uses 32 bytes of IOSPACE */ 71 72 73#define LEMAC_REG_EID0 0x80 /* EISA Identification 0 */ 74#define LEMAC_REG_EID1 0x81 /* EISA Identification 1 */ 75#define LEMAC_REG_EID2 0x82 /* EISA Identification 2 */ 76#define LEMAC_REG_EID3 0x83 /* EISA Identification 3 */ 77#define LEMAC_REG_EIC 0x84 /* EISA Control */ 78 79/* Control Page (Page 0) Definitions */ 80 81#define LEMAC_MCTBL_BITS 9 82#define LEMAC_MCTBL_OFF 512 83#define LEMAC_MCTBL_SIZE (1 << (LEMAC_MCTBL_BITS - 3)) 84#define LEMAC_CRC32_POLY 0xEDB88320UL /* CRC-32 Poly -- Little Endian) */ 85 86/* EEPROM Definitions */ 87 88#define LEMAC_EEP_CKSUM 0 /* The valid checksum is 0 */ 89#define LEMAC_EEP_SIZE 32 /* EEPROM is 32 bytes */ 90#define LEMAC_EEP_DELAY 2000 /* 2ms = 2000us */ 91#define LEMAC_EEP_PRDNM 8 /* Product Name Offset */ 92#define LEMAC_EEP_PRDNMSZ 8 /* Product Name Size */ 93#define LEMAC_EEP_SWFLAGS 16 /* Software Options Offset */ 94#define LEMAC_EEP_SETUP 23 /* Setup Options Offset */ 95 96#define LEMAC_EEP_SW_SQE 0x10 /* Enable TX_SQE on Transmits */ 97#define LEMAC_EEP_SW_LAB 0x08 /* Enable TX_LAB on Transmits */ 98#define LEMAC_EEP_ST_DRAM 0x02 /* Enable extra DRAM */ 99 100#define LEMAC_ADP_ROMSZ 32 /* Size of Address PROM */ 101 102/* Receive Status Definitions */ 103 104#define LEMAC_RX_PLL 0x01 /* Phase Lock Lost */ 105#define LEMAC_RX_CRC 0x02 /* CRC Error */ 106#define LEMAC_RX_DBE 0x04 /* Dribble Bit Error */ 107#define LEMAC_RX_MCM 0x08 /* Multicast Match */ 108#define LEMAC_RX_IAM 0x10 /* Individual Address Match */ 109#define LEMAC_RX_OK 0x80 /* No Errors */ 110 111/* Transmit Status Definitions (not valid if TXD == 0) */ 112 113#define LEMAC_TS_RTRYMSK 0x0F /* Retries of last TX PDU */ 114#define LEMAC_TS_ECL 0x10 /* Excessive collision of ... */ 115#define LEMAC_TS_LCL 0x20 /* Late collision of ... */ 116#define LEMAC_TS_ID 0x40 /* Initially Deferred ... */ 117#define LEMAC_TS_NCL 0x08 /* No carrier loopback ... */ 118 119/* Transmit Control Definitions */ 120 121#define LEMAC_TX_ISA 0x01 /* Insert Source Address (no) */ 122#define LEMAC_TX_IFC 0x02 /* Insert Frame Check (yes) */ 123#define LEMAC_TX_PAD 0x04 /* Zero PAD to minimum length (yes) */ 124#define LEMAC_TX_LAB 0x08 /* Less Aggressive Backoff (no) */ 125#define LEMAC_TX_QMD 0x10 /* Q-Mode (yes) */ 126#define LEMAC_TX_STP 0x20 /* Stop on Error (no) */ 127#define LEMAC_TX_SQE 0x40 /* SQE Enable (yes) */ 128 129#define LEMAC_TX_FLAGS (LEMAC_TX_IFC|LEMAC_TX_PAD|LEMAC_TX_QMD|\ 130 LEMAC_TX_SQE) 131#define LEMAC_TX_HDRSZ 4 /* Size of TX header */ 132 133/* Transmit Done Queue Status Definitions */ 134 135#define LEMAC_TDQ_COL 0x03 /* Collision Mask */ 136#define LEMAC_TDQ_NOCOL 0x00 /* No Collisions */ 137#define LEMAC_TDQ_ONECOL 0x01 /* One Collision */ 138#define LEMAC_TDQ_MULCOL 0x02 /* Multiple Collisions */ 139#define LEMAC_TDQ_EXCCOL 0x03 /* Excessive Collisions */ 140#define LEMAC_TDQ_ID 0x04 /* Initially Deferred */ 141#define LEMAC_TDQ_LCL 0x08 /* Late Collision (will TX_STP) */ 142#define LEMAC_TDQ_NCL 0x10 /* No carrier loopback */ 143#define LEMAC_TDQ_SQE 0x20 /* SQE error */ 144 145/* Control / Status Definitions */ 146 147#define LEMAC_CS_RXD 0x01 /* Receiver Disabled */ 148#define LEMAC_CS_TXD 0x02 /* Transmitter Disabled */ 149#define LEMAC_CS_RNE 0x04 /* Receive Queue Not Empty */ 150#define LEMAC_CS_TNE 0x08 /* Transmit Done Queue Not Empty */ 151#define LEMAC_CS_MBZ4 0x10 /* MBZ */ 152#define LEMAC_CS_MCE 0x20 /* Multicast Enable */ 153#define LEMAC_CS_PME 0x40 /* Promiscuous Mode Enable */ 154#define LEMAC_CS_RA 0x80 /* Runt Accept */ 155 156/* Control Definitions */ 157 158#define LEMAC_CTL_LED 0x02 /* LED state (inverted) */ 159#define LEMAC_CTL_PSL 0x40 /* Port Select (1=AUI, 0=UTP) */ 160#define LEMAC_CTL_APD 0x80 /* Auto Port Disable */ 161 162/* Interrupt Control Definitions */ 163 164#define LEMAC_IC_RXD 0x01 /* Enable RXD Interrupt */ 165#define LEMAC_IC_TXD 0x02 /* Enable TXD Interrupt */ 166#define LEMAC_IC_RNE 0x04 /* Enable RNE Interrupt */ 167#define LEMAC_IC_TNE 0x08 /* Enable TNE Interrupt */ 168#define LEMAC_IC_ALL 0x0F /* Enable RXD,TXD,RNE,TNE */ 169#define LEMAC_IC_IRQMSK 0x60 /* Interrupt Select */ 170#define LEMAC_IC_IRQ5 0x00 /* Select IRQ 5 */ 171#define LEMAC_IC_IRQ10 0x20 /* Select IRQ 10 */ 172#define LEMAC_IC_IRQ11 0x40 /* Select IRQ 11 */ 173#define LEMAC_IC_IRQ15 0x60 /* Select IRQ 15 */ 174#define LEMAC_IC_IE 0x80 /* Interrupt Enable */ 175 176/* I/O Page Definitions */ 177 178#define LEMAC_IOP_EEINIT 0xC0 /* Perform a board init/reset */ 179#define LEMAC_IOP_EEREAD 0xE0 /* Start a read from EEPROM */ 180 181/* Configuration / Management Definitions */ 182 183#define LEMAC_CNF_DRAM 0x02 /* Extra on-board DRAM is available */ 184#define LEMAC_CNF_NOLINK 0x20 /* UTP port is UP */ 185 186#endif /* _LEMAC_H_ */ 187