1/* $OpenBSD: ts102reg.h,v 1.3 2003/06/18 17:50:23 miod Exp $ */ 2/* $NetBSD: ts102reg.h,v 1.11 2006/03/06 21:43:29 macallan Exp $ */ 3 4/*- 5 * Copyright (c) 1998 The NetBSD Foundation, Inc. 6 * All rights reserved. 7 * 8 * This code is derived from software contributed to The NetBSD Foundation 9 * by Matt Thomas. 10 * 11 * Redistribution and use in source and binary forms, with or without 12 * modification, are permitted provided that the following conditions 13 * are met: 14 * 1. Redistributions of source code must retain the above copyright 15 * notice, this list of conditions and the following disclaimer. 16 * 2. Redistributions in binary form must reproduce the above copyright 17 * notice, this list of conditions and the following disclaimer in the 18 * documentation and/or other materials provided with the distribution. 19 * 20 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS 21 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 22 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 23 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS 24 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 * POSSIBILITY OF SUCH DAMAGE. 31 */ 32#ifndef _SPARC_DEV_TS102REG_H 33#define _SPARC_DEV_TS102REG_H 34 35/* The TS102 consumes a 256MB region of the SPARCbook 3's address space. 36 */ 37#define TS102_OFFSET_REGISTERS 0x02000000 38#define TS102_OFFSET_CARD_A_ATTR_SPACE 0x04000000 39#define TS102_OFFSET_CARD_B_ATTR_SPACE 0x05000000 40#define TS102_SIZE_ATTR_SPACE 0x01000000 41#define TS102_OFFSET_CARD_A_IO_SPACE 0x06000000 42#define TS102_OFFSET_CARD_B_IO_SPACE 0x07000000 43#define TS102_SIZE_IO_SPACE 0x01000000 44#define TS102_OFFSET_CARD_A_MEM_SPACE 0x08000000 45#define TS102_OFFSET_CARD_B_MEM_SPACE 0x0c000000 46#define TS102_SIZE_MEM_SPACE 0x04000000 47 48/* There are two separate register blocks within the TS102. The first 49 * gives access to PCMCIA card specific resources, and the second gives 50 * access to the microcontroller interface 51 */ 52#define TS102_REG_CARD_A_INT 0x0000 /* Card A Interrupt Register */ 53#define TS102_REG_CARD_A_STS 0x0004 /* Card A Status Register */ 54#define TS102_REG_CARD_A_CTL 0x0008 /* Card A Control Register */ 55#define TS102_REG_CARD_B_INT 0x0010 /* Card B Interrupt Register */ 56#define TS102_REG_CARD_B_STS 0x0014 /* Card B Status Register */ 57#define TS102_REG_CARD_B_CTL 0x0018 /* Card B Control Register */ 58#define TS102_REG_UCTRL_INT 0x0020 /* Microcontroller Interrupt Register */ 59#define TS102_REG_UCTRL_DATA 0x0024 /* Microcontroller Data Register */ 60#define TS102_REG_UCTRL_STS 0x0028 /* Microcontroller Status Register */ 61 62struct uctrl_regs { 63 volatile uint8_t intr; /* Microcontroller Interrupt Reg */ 64 volatile uint8_t filler0[3]; 65 volatile uint8_t data; /* Microcontroller Data Reg */ 66 volatile uint8_t filler1[3]; 67 volatile uint8_t stat; /* Microcontroller Status Reg */ 68 volatile uint8_t filler2[3]; 69}; 70 71/* TS102 Card Interrupt Register definitions. 72 * 73 * There is one 16-bit interrupt register for each card. Each register 74 * contains interrupt status (read) and clear (write) bits and an 75 * interrupt mask for each of the four interrupt sources. 76 * 77 * The request bit is the logical AND of the status and the mask bit, 78 * and indicated and an interrupt is being requested. The mask bits 79 * allow masking of individual interrupts. An interrupt is enabled when 80 * the mask is set to 1 and is clear by write a 1 to the associated 81 * request bit. 82 * 83 * The card interrupt register also contain the soft reset flag. 84 * Setting this bit to 1 will the SPARCbook 3 to be reset. 85 */ 86#define TS102_CARD_INT_RQST_IRQ 0x0001 87#define TS102_CARD_INT_RQST_WP_STATUS_CHANGED 0x0002 88#define TS102_CARD_INT_RQST_BATTERY_STATUS_CHANGED 0x0004 89#define TS102_CARD_INT_RQST_CARDDETECT_STATUS_CHANGED 0x0008 90#define TS102_CARD_INT_STATUS_IRQ 0x0010 91#define TS102_CARD_INT_STATUS_WP_STATUS_CHANGED 0x0020 92#define TS102_CARD_INT_STATUS_BATTERY_STATUS_CHANGED 0x0040 93#define TS102_CARD_INT_STATUS_CARDDETECT_STATUS_CHANGED 0x0080 94#define TS102_CARD_INT_MASK_IRQ 0x0100 95#define TS102_CARD_INT_MASK_WP_STATUS 0x0200 96#define TS102_CARD_INT_MASK_BATTERY_STATUS 0x0400 97#define TS102_CARD_INT_MASK_CARDDETECT_STATUS 0x0800 98#define TS102_CARD_INT_SOFT_RESET 0x1000 99 100/* TS102 Card Status Register definitions. The Card Status Register 101 * contains card status and control bit. 102 */ 103#define TS102_CARD_STS_PRES 0x0001 /* Card Present (1) */ 104#define TS102_CARD_STS_IO 0x0002 /* (1) I/O Card, (0) = Mem Card */ 105#define TS102_CARD_STS_TYPE3 0x0004 /* Type-3 PCMCIA card (disk) */ 106#define TS102_CARD_STS_VCC 0x0008 /* Vcc (0=5V, 1=3.3V) */ 107#define TS102_CARD_STS_VPP1_MASK 0x0030 /* Programming Voltage Control2 */ 108#define TS102_CARD_STS_VPP1_NC 0x0030 /* NC */ 109#define TS102_CARD_STS_VPP1_VCC 0x0020 /* Vcc (3.3V or 5V) */ 110#define TS102_CARD_STS_VPP1_VPP 0x0010 /* Vpp (12V) */ 111#define TS102_CARD_STS_VPP1_0V 0x0000 /* 0V */ 112#define TS102_CARD_STS_VPP2_MASK 0x00c0 /* Programming Voltage Control1 */ 113#define TS102_CARD_STS_VPP2_NC 0x00c0 /* NC */ 114#define TS102_CARD_STS_VPP2_VCC 0x0080 /* Vcc (3.3V or 5V) */ 115#define TS102_CARD_STS_VPP2_VPP 0x0040 /* Vpp (12V) */ 116#define TS102_CARD_STS_VPP2_0V 0x0000 /* 0V */ 117#define TS102_CARD_STS_WP 0x0100 /* Write Protect (1) */ 118#define TS102_CARD_STS_BVD_MASK 0x0600 /* Battery Voltage Detect */ 119#define TS102_CARD_STS_BVD_GOOD 0x0600 /* Battery good */ 120#define TS102_CARD_STS_BVD_LOW_OK 0x0400 /* Battery low, data OK */ 121#define TS102_CARD_STS_BVD_LOW_SUSPECT1 0x0200 /* Battery low, data suspect */ 122#define TS102_CARD_STS_BVD_LOW_SUSPECT0 0x0000 /* Battery low, data suspect */ 123#define TS102_CARD_STS_LVL 0x0800 /* Level (1) / Edge */ 124#define TS102_CARD_STS_RDY 0x1000 /* Ready (1) / Not Busy */ 125#define TS102_CARD_STS_VCCEN 0x2000 /* Powered Up (0) */ 126#define TS102_CARD_STS_RIEN 0x4000 /* Not Supported */ 127#define TS102_CARD_STS_ACEN 0x8000 /* Access Enabled (1) */ 128 129/* TS102 Card Control Register definitions 130 */ 131#define TS102_CARD_CTL_AA_MASK 0x0003 /* Attribute Address A[25:24] */ 132#define TS102_CARD_CTL_IA_MASK 0x000c /* I/O Address A[25:24] */ 133#define TS102_CARD_CTL_IA_BITPOS 2 /* */ 134#define TS102_CARD_CTL_CES_MASK 0x0070 /* CE/address setup time */ 135#define TS102_CARD_CTL_CES_BITPOS 4 /* n+1 clocks */ 136#define TS102_CARD_CTL_OWE_MASK 0x0380 /* OE/WE width */ 137#define TS102_CARD_CTL_OWE_BITPOS 7 /* n+2 clocks */ 138#define TS102_CARD_CTL_CEH 0x0400 /* Chip enable hold time */ 139 /* (0) - 1 clock */ 140 /* (1) - 2 clocks */ 141#define TS102_CARD_CTL_SBLE 0x0800 /* SBus little endian */ 142#define TS102_CARD_CTL_PCMBE 0x1000 /* PCMCIA big endian */ 143#define TS102_CARD_CTL_RAHD 0x2000 /* Read ahead enable */ 144#define TS102_CARD_CTL_INCDIS 0x4000 /* Address increment disable */ 145#define TS102_CARD_CTL_PWRD 0x8000 /* Power down */ 146 147/* Microcontroller Interrupt Register 148 */ 149#define TS102_UCTRL_INT_TXE_REQ 0x01 /* transmit FIFO empty */ 150#define TS102_UCTRL_INT_TXNF_REQ 0x02 /* transmit FIFO not full */ 151#define TS102_UCTRL_INT_RXNE_REQ 0x04 /* receive FIFO not empty */ 152#define TS102_UCTRL_INT_RXO_REQ 0x08 /* receive FIFO overflow */ 153#define TS102_UCTRL_INT_TXE_MSK 0x10 /* transmit FIFO empty */ 154#define TS102_UCTRL_INT_TXNF_MSK 0x20 /* transmit FIFO not full */ 155#define TS102_UCTRL_INT_RXNE_MSK 0x40 /* receive FIFO not empty */ 156#define TS102_UCTRL_INT_RXO_MSK 0x80 /* receive FIFO overflow */ 157 158/* TS102 Microcontroller Data Register (only 8 bits are significant). 159 */ 160#define TS102_UCTRL_DATA_MASK 0xff 161 162/* TS102 Microcontroller Status Register. 163 * read 1 if asserted 164 * write 1 to clear 165 */ 166#define TS102_UCTRL_STS_TXE_STA 0x01 /* transmit FIFO empty */ 167#define TS102_UCTRL_STS_TXNF_STA 0x02 /* transmit FIFO not full */ 168#define TS102_UCTRL_STS_RXNE_STA 0x04 /* receive FIFO not empty */ 169#define TS102_UCTRL_STS_RXO_STA 0x08 /* receive FIFO overflow */ 170#define TS102_UCTRL_STS_MASK 0x0F /* Only 4 bits significant */ 171 172enum ts102_opcode { /* Argument Returned */ 173 TS102_OP_RD_SERIAL_NUM=0x01, /* none ack + 4 bytes */ 174 TS102_OP_RD_ETHER_ADDR=0x02, /* none ack + 6 bytes */ 175 TS102_OP_RD_HW_VERSION=0x03, /* none ack + 2 bytes */ 176 TS102_OP_RD_UCTLR_VERSION=0x04, /* none ack + 2 bytes */ 177 TS102_OP_RD_MAX_TEMP=0x05, /* none ack + 1 bytes */ 178 TS102_OP_RD_MIN_TEMP=0x06, /* none ack + 1 bytes */ 179 TS102_OP_RD_CURRENT_TEMP=0x07, /* none ack + 1 bytes */ 180 TS102_OP_RD_SYSTEM_VARIANT=0x08, /* none ack + 4 bytes */ 181 TS102_OP_RD_POWERON_CYCLES=0x09, /* none ack + 4 bytes */ 182 TS102_OP_RD_POWERON_SECONDS=0x0a, /* none ack + 4 bytes */ 183 TS102_OP_RD_RESET_STATUS=0x0b, /* none ack + 1 bytes */ 184#define TS102_RESET_STATUS_RESERVED0 0x00 185#define TS102_RESET_STATUS_POWERON 0x01 186#define TS102_RESET_STATUS_KEYBOARD 0x02 187#define TS102_RESET_STATUS_WATCHDOG 0x03 188#define TS102_RESET_STATUS_TIMEOUT 0x04 189#define TS102_RESET_STATUS_SOFTWARE 0x05 190#define TS102_RESET_STATUS_BROWNOUT 0x06 191#define TS102_RESET_STATUS_RESERVED1 0x07 192 TS102_OP_RD_EVENT_STATUS=0x0c, /* none ack + 2 bytes */ 193#define TS102_EVENT_STATUS_SHUTDOWN_REQUEST 0x0001 194#define TS102_EVENT_STATUS_LOW_POWER_WARNING 0x0002 195/* Internal Warning Changed 0x0002 */ 196#define TS102_EVENT_STATUS_VERY_LOW_POWER_WARNING 0x0004 197/* Discharge Event 0x0004 */ 198#define TS102_EVENT_STATUS_BATT_CHANGED 0x0008 199/* Internal Status Changed 0x0008 */ 200#define TS102_EVENT_STATUS_EXT_KEYBOARD_STATUS_CHANGE 0x0010 201#define TS102_EVENT_STATUS_EXT_MOUSE_STATUS_CHANGE 0x0020 202#define TS102_EVENT_STATUS_EXTERNAL_VGA_STATUS_CHANGE 0x0040 203#define TS102_EVENT_STATUS_LID_STATUS_CHANGE 0x0080 204#define TS102_EVENT_STATUS_MICROCONTROLLER_ERROR 0x0100 205#define TS102_EVENT_STATUS_RESERVED 0x0200 206/* Wakeup 0x0200 */ 207#define TS102_EVENT_STATUS_EXT_BATT_STATUS_CHANGE 0x0400 208#define TS102_EVENT_STATUS_EXT_BATT_CHARGING_STATUS_CHANGE 0x0800 209#define TS102_EVENT_STATUS_EXT_BATT_LOW_POWER 0x1000 210#define TS102_EVENT_STATUS_DC_STATUS_CHANGE 0x2000 211#define TS102_EVENT_STATUS_CHARGING_STATUS_CHANGE 0x4000 212#define TS102_EVENT_STATUS_POWERON_BTN_PRESSED 0x8000 213 TS102_OP_RD_REAL_TIME_CLK=0x0d, /* none ack + 7 bytes */ 214 TS102_OP_RD_EXT_VGA_PORT=0x0e, /* none ack + 1 bytes */ 215 TS102_OP_RD_UCTRL_ROM_CKSUM=0x0f, /* none ack + 2 bytes */ 216 TS102_OP_RD_ERROR_STATUS=0x10, /* none ack + 2 bytes */ 217#define TS102_ERROR_STATUS_NO_ERROR 0x00 218#define TS102_ERROR_STATUS_COMMAND_ERROR 0x01 219#define TS102_ERROR_STATUS_EXECUTION_ERROR 0x02 220#define TS102_ERROR_STATUS_PHYSICAL_ERROR 0x04 221 TS102_OP_RD_EXT_STATUS=0x11, /* none ack + 2 bytes */ 222#define TS102_EXT_STATUS_MAIN_POWER_AVAILABLE 0x0001 223#define TS102_EXT_STATUS_INTERNAL_BATTERY_ATTACHED 0x0002 224#define TS102_EXT_STATUS_EXTERNAL_BATTERY_ATTACHED 0x0004 225#define TS102_EXT_STATUS_EXTERNAL_VGA_ATTACHED 0x0008 226#define TS102_EXT_STATUS_EXTERNAL_KEYBOARD_ATTACHED 0x0010 227#define TS102_EXT_STATUS_EXTERNAL_MOUSE_ATTACHED 0x0020 228#define TS102_EXT_STATUS_LID_DOWN 0x0040 229#define TS102_EXT_STATUS_INTERNAL_BATTERY_CHARGING 0x0080 230#define TS102_EXT_STATUS_EXTERNAL_BATTERY_CHARGING 0x0100 231#define TS102_EXT_STATUS_INTERNAL_BATTERY_DISCHARGING 0x0200 232#define TS102_EXT_STATUS_EXTERNAL_BATTERY_DISCHARGING 0x0400 233 TS102_OP_RD_USER_CONFIG=0x12, /* none ack + 2 bytes */ 234 TS102_OP_RD_UCTRL_VLT=0x13, /* none ack + 1 bytes */ 235 TS102_OP_RD_INT_BATT_VLT=0x14, /* none ack + 1 bytes */ 236 TS102_OP_RD_DC_IN_VLT=0x15, /* none ack + 1 bytes */ 237 TS102_OP_RD_HORZ_PRT_VLT=0x16, /* none ack + 1 bytes */ 238 TS102_OP_RD_VERT_PTR_VLT=0x17, /* none ack + 1 bytes */ 239 TS102_OP_RD_INT_CHARGE_RATE=0x18, /* none ack + 1 bytes */ 240 TS102_OP_RD_EXT_CHARGE_RATE=0x19, /* none ack + 1 bytes */ 241 TS102_OP_RD_RTC_ALARM=0x1a, /* none ack + 7 bytes */ 242 TS102_OP_RD_EVENT_STATUS_NO_RESET=0x1b, /* none ack + 2 bytes */ 243 TS102_OP_RD_INT_KBD_LAYOUT=0x1c, /* none ack + 2 bytes */ 244 TS102_OP_RD_EXT_KBD_LAYOUT=0x1d, /* none ack + 2 bytes */ 245 TS102_OP_RD_EEPROM_STATUS=0x1e, /* none ack + 2 bytes */ 246#define TS102_EEPROM_STATUS_FACTORY_AREA_CHECKSUM_FAIL 0x01 247#define TS102_EEPROM_STATUS_CONSUMER_AREA_CHECKSUM_FAIL 0x02 248#define TS102_EEPROM_STATUS_USER_AREA_CHECKSUM_FAIL 0x04 249#define TS102_EEPROM_STATUS_VPD_AREA_CHECKSUM_FAIL 0x08 250 251 /* Read/Write/Modify Commands 252 */ 253 TS102_OP_CTL_LCD=0x20, /* 4 byte mask ack + 4 bytes */ 254#define TS102_LCD_CAPS_LOCK 0x0001 255#define TS102_LCD_SCROLL_LOCK 0x0002 256#define TS102_LCD_NUMLOCK 0x0004 257#define TS102_LCD_DISK_ACTIVE 0x0008 258#define TS102_LCD_LAN_ACTIVE 0x0010 259#define TS102_LCD_WAN_ACTIVE 0x0020 260#define TS102_LCD_PCMCIA_ACTIVE 0x0040 261#define TS102_LCD_DC_OK 0x0080 262#define TS102_LCD_COMPOSE 0x0100 263 TS102_OP_CTL_BITPORT=0x21, /* mask ack + 1 byte */ 264#define TS102_BITPORT_TFTPWR 0x01 /* TFT power (low) */ 265#define TS102_BITPORT_SYNCINVA 0x02 /* ext. monitor sync (low) */ 266#define TS102_BITPORT_SYNCINVB 0x04 /* ext. monitor sync (low) */ 267#define TS102_BITPORT_BP_DIS 0x08 /* no bootprom from pcmcia (high) */ 268 /* boot from pcmcia (low */ 269#define TS102_BITPORT_ENCSYNC 0x10 /* enab composite sync (low) */ 270#define TS102_BITPORT_DISKPOWER 0x20 /* power to internal disk */ 271 TS102_OP_CTL_DEV=0x22, /* mask ack + 1 byte */ 272#define TS102_DEVCTL_CHARGE_DISABLE 0x01 /* dis/en charging */ 273#define TS102_DEVCTL_POINTER_DISABLE 0x02 /* dis/en pointer */ 274#define TS102_DEVCTL_KEYCLICK 0x04 /* keyclick? */ 275#define TS102_DEVCTL_INT_BTNCLICK 0x10 /* beep on ext. mouse click */ 276#define TS102_DEVCTL_EXT_BTNCLICK 0x20 /* ext. button click?? */ 277 TS102_OP_CTL_SPEAKER_VOLUME=0x23, /* mask ack + 1 byte */ 278 TS102_OP_CTL_TFT_BRIGHTNESS=0x24, /* mask ack + 1 byte */ 279 TS102_OP_CTL_WATCHDOG=0x25, /* mask ack + 1 byte */ 280 TS102_OP_CTL_FCTRY_EEPROM=0x26, /* mask ack + 1 byte */ 281 TS102_OP_CTL_SECURITY_KEY=0x27, /* no idea */ 282 TS102_OP_CTL_KDB_TIME_UNTL_RTP=0x28, /* mask ack + 1 byte */ 283 TS102_OP_CTL_KBD_TIME_BTWN_RPTS=0x29, /* mask ack + 1 byte */ 284 TS102_OP_CTL_TIMEZONE=0x2a, /* mask ack + 1 byte */ 285 TS102_OP_CTL_MARK_SPACE_RATIO=0x2b, /* mask ack + 1 byte */ 286 TS102_OP_CTL_MOUSE_SENS=0x2c, /* mask ack + 1 byte */ 287 TS102_OP_CTL_MOUSE_SCAN=0x2d, /* no idea invalid?*/ 288 TS102_OP_CTL_DIAGNOSTIC_MODE=0x2e, /* mask ack + 1 byte */ 289#define TS102_DIAGNOSTIC_MODE_CMD_DIAG_ON_LCD 0x01 290#define TS102_DIAGNOSTIC_MODE_KDB_MS_9600 0x02 291 TS102_OP_CTL_SCREEN_CONTRAST=0x2f, /* mask ack + 1 byte */ 292 293 /* Commands returning no status 294 */ 295 TS102_OP_CMD_RING_BELL=0x30, /* msb,lsb ack */ 296 TS102_OP_RD_INPUT_SOURCE=0x31, /* no idea */ 297 TS102_OP_CMD_DIAGNOSTIC_STATUS=0x32, /* msb,lsb ack */ 298 TS102_OP_CMD_CLR_KEY_COMBO_TBL=0x33, /* none ack */ 299 TS102_OP_CMD_SOFTWARE_RESET=0x34, /* none ack */ 300 TS102_OP_CMD_SET_RTC=0x35, /* smhddmy ack */ 301 TS102_OP_CMD_RECAL_PTR=0x36, /* none ack */ 302 TS102_OP_CMD_SET_BELL_FREQ=0x37, /* msb,lsb ack */ 303 TS102_OP_CMD_SET_INT_BATT_RATE=0x39, /* charge-lvl ack */ 304 TS102_OP_CMD_SET_EXT_BATT_RATE=0x3a, /* charge-lvl ack */ 305 TS102_OP_CMD_SET_RTC_ALARM=0x3b, /* smhddmy ack */ 306 307 /* Block transfer commands 308 */ 309 TS102_OP_BLK_RD_EEPROM=0x40, /* len off ack <data> */ 310 TS102_OP_BLK_WR_EEPROM=0x41, /* len off <data> ack */ 311 TS102_OP_BLK_WR_STATUS=0x42, /* len off <data> ack */ 312 TS102_OP_BLK_DEF_SPCL_CHAR=0x43, /* len off <8b data> ack */ 313#define TS102_BLK_OFF_DEF_WAN1 0 314#define TS102_BLK_OFF_DEF_WAN2 1 315#define TS102_BLK_OFF_DEF_LAN1 2 316#define TS102_BLK_OFF_DEF_LAN2 3 317#define TS102_BLK_OFF_DEF_PCMCIA 4 318#define TS102_BLK_OFF_DEF_DC_GOOD 5 319#define TS102_BLK_OFF_DEF_BACKSLASH 6 320 321 /* Generic commands 322 */ 323 TS102_OP_GEN_DEF_KEY_COMBO_ENT=0x50, /* seq com-length ack */ 324 TS102_OP_GEN_DEF_STRING_TBL_ENT=0x51, /* str-code len <str> ack */ 325 TS102_OP_GEN_DEF_STS_CTRN_DISP=0x52, /* len <msg> ack */ 326 327 /* Generic commands with optional status 328 */ 329 TS102_OP_GEN_STS_EMU_COMMAND=0x64, /* <command> ack */ 330 TS102_OP_GEN_STS_RD_EMU_REGISTER=0x65, /* reg ack + 1 byte */ 331 TS102_OP_GEN_STS_WR_EMU_REGISTER=0x66, /* reg,val ack */ 332 TS102_OP_GEN_STS_RD_EMU_RAM=0x67, /* addr ack + 1 byte */ 333 TS102_OP_GEN_STS_WR_EMU_RAM=0x68, /* addr,val ack */ 334 TS102_OP_GEN_STS_RD_BQ_REGISTER=0x69, /* reg ack + 1 byte */ 335 TS102_OP_GEN_STS_WR_BQ_REGISTER=0x6a, /* reg,val ack */ 336 337 /* Administration commands 338 */ 339 TS102_OP_ADMIN_SET_USER_PASS=0x70, /* len <pass> ack */ 340 TS102_OP_ADMIN_VRFY_USER_PASS=0x71, /* len <pass> ack + status */ 341 TS102_OP_ADMIN_GET_SYSTEM_PASS=0x72, /* none ack + <7bytekey> */ 342 TS102_OP_ADMIN_VRFY_SYSTEM_PASS=0x73, /* len <pass> ack + status */ 343 TS102_OP_RD_INT_CHARGE_LEVEL=0x7a, /* ack + 2 byte */ 344 TS102_OP_RD_EXT_CHARGE_LEVEL=0x7b, /* ack + 2 byte */ 345 TS102_OP_SLEEP=0x80, /* supposedly sleeps, not sure */ 346 TS102_OP_ADMIN_POWER_OFF=0x82, /* len <pass> none */ 347 TS102_OP_ADMIN_POWER_RESTART=0x83, /* msb,xx,lsb none */ 348}; 349 350#endif /* _SPARC_DEV_TS102REG_H */ 351