1# $NetBSD: TADPOLE3GX,v 1.78 2019/05/08 13:40:16 isaki Exp $ 2 3include "arch/sparc/conf/std.sparc" 4 5#options INCLUDE_CONFIG_FILE # embed config file in kernel binary 6 7# all supported SPARCbooks have V8 CPUs 8makeoptions CCPUOPTS="-mcpu=v8 -mtune=v8" 9 10maxusers 32 11 12## System kernel configuration. See options(4) for more detail. 13 14 15# Options for variants of the Sun SPARC architecure. 16# We currently support three architecture types; at least one is required. 17options SUN4M # sun4m - SS10, SS20, Classic, etc. 18 19## System options specific to the sparc machine type 20 21# Blink the power LED on some machines to indicate the system load. 22#options BLINK 23 24# wsdisplay options 25#options WSEMUL_SUN 26options WSEMUL_VT100 27options WSDISPLAY_COMPAT_RAWKBD # can get raw scancodes 28options WSDISPLAY_CUSTOM_OUTPUT # wsconsctl(8) 29 30# black on white, kernel output in green 31options WS_DEFAULT_FG=WSCOL_BLACK 32options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 33options WS_KERNEL_FG=WSCOL_GREEN 34options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 35 36options WSDISPLAY_COMPAT_PCVT # emulate some ioctls 37options WSDISPLAY_COMPAT_SYSCONS # emulate some ioctls 38options WSDISPLAY_COMPAT_USL # wsconscfg VT handling 39 40options WSDISPLAY_DEFAULTSCREENS=1 41 42options SPARCBOOK_CMD # enable screen switching with lAlt-Fn 43#options FONT_GALLANT12x22 # the console font 44options FONT_BOLD8x16 # a somewhat smaller font 45 46#### System options that are the same for all ports 47 48## Root device configuration: change the ?'s if you are going to use a 49## nonstandard root partition (other than where the kernel is booted from) 50## and/or nonstandard root type (not ffs or nfs). Normally this can be 51## automagically determined at boot time. 52 53config netbsd root on ? type ? 54 55## System call tracing (see ktrace(1)). 56options KTRACE 57 58## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 59options SYSVMSG # System V message queues 60options SYSVSEM # System V semaphores 61options SYSVSHM # System V shared memory 62 63options USERCONF # userconf(4) support 64#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 65#options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 66 67## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 68options NFS_BOOT_BOOTPARAM 69#options NFS_BOOT_BOOTP 70options NFS_BOOT_DHCP 71 72#### Debugging options 73 74## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 75## serial console break or keyboard reset, where the PROM would normally 76## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 77options DDB # kernel dynamic debugger 78pseudo-device ksyms 79options DDB_HISTORY_SIZE=100 # enable history editing in DDB 80#options DDB_ONPANIC=1 # see also sysctl(7): `ddb.onpanic' 81 82## You may also use gdb, on another computer connected to this machine over 83## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 84## KGDB_DEV is a dev_t encoded device number of the serial port to use. 85## (0xc01 = ttya, 0xc02 = ttyb.) 86#options KGDB # support for kernel gdb 87#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 88#options KGDB_DEVRATE=38400 # baud rate 89 90 91## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 92## such that gdb(1) can be used on a kernel coredump. 93 94makeoptions DEBUG="-g" 95 96 97## Adds code to the kernel that does internal consistency checks, and will 98## cause the kernel to panic if corruption of internal data structures 99## is detected. 100#options DIAGNOSTIC # extra kernel sanity checking 101 102## Enable (possibly expensive) debugging code that may also display messages 103## on the system console 104#options DEBUG 105#options LOCKDEBUG 106#options SYSCALL_DEBUG 107 108## Make SCSI error messages more verbose when explaining their meanings. 109options SCSIVERBOSE 110 111## `INSECURE' turns off the kernel security level (securelevel = 0 always). 112## This allows writing to /dev/mem, loading kernel modules while multi-user, 113## and other insecurities good only for development work. Do not use this 114## option on a production machine. 115options INSECURE 116 117## `FDSCRIPTS' allows non-readable but executable scripts by providing a 118## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 119## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 120## opaque file mechanism. Perl calls this "secure setuid scripts." 121 122#options FDSCRIPTS 123#options SETUIDSCRIPTS 124 125## Options for compatibility with previous releases foreign system binaries. 126## In the cases of COMPAT_SUNOS, you may need to set up additional user-level 127## utilities or system configuration files. See compat_sunos(8). 128 129include "conf/compat_netbsd10.config" 130options COMPAT_SUNOS # SunOS 4.x binary compatibility 131 132## File systems. You probably need at least one of FFS or NFS. 133file-system FFS # Berkeley Fast Filesystem 134file-system NFS # Sun NFS-compatible filesystem client 135file-system KERNFS # kernel data-structure filesystem 136#file-system NULLFS # NULL layered filesystem 137file-system MFS # memory-based filesystem 138#file-system FDESC # user file descriptor filesystem 139#file-system UMAPFS # uid/gid remapping filesystem 140#file-system LFS # Log-based filesystem (still experimental) 141file-system PROCFS # /proc 142file-system CD9660 # ISO 9660 + Rock Ridge file system 143#file-system UNION # union file system 144file-system MSDOSFS # MS-DOS FAT filesystem(s). 145file-system PTYFS # /dev/pts/N support 146 147## File system options. 148options NFSSERVER # Sun NFS-compatible filesystem server 149options QUOTA # legacy UFS quotas 150options QUOTA2 # new, in-filesystem UFS quotas 151#options FFS_EI # FFS Endian Independent support 152#options FFS_NO_SNAPSHOT # No FFS snapshot support 153options UFS_EXTATTR # Extended attribute support for UFS1 154 155## Network protocol support. In most environments, INET is required. 156options INET # IP (Internet Protocol) v4 157#options GATEWAY # packet forwarding ("router switch") 158#options MROUTING # packet forwarding of multicast packets 159#options PIM # Protocol Independent Multicast 160#options NETATALK # AppleTalk (over Ethernet) protocol 161options NTP # Network Time Protocol in-kernel support 162#options PPS_SYNC # Add serial line synchronization for NTP 163options PPP_BSDCOMP # Add BSD compression to ppp device 164options PPP_DEFLATE # Add deflate (libz) compression to ppp device 165options PPP_FILTER # Add active filters for ppp (via bpf) 166#options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 167 168 169#### Main bus and CPU .. all systems. 170mainbus0 at root 171cpu0 at mainbus0 172 173#### Bus types found on SPARC systems. 174 175obio0 at mainbus0 # sun4 and sun4m 176iommu0 at mainbus0 # sun4m 177sbus0 at iommu0 # sun4m 178 179## SBus to PCMCIA bridge 180tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 181pcmcia* at tslot? 182 183#### Standard system devices -- all required for a given architecture 184 185## Auxiliary system registers on sun4c and sun4m 186auxreg0 at obio0 # sun4m 187 188## Additional auxiliary system registers on Sparcbook 189auxiotwo0 at obio0 # sun4m 190 191## Clock control on SPARCbook - used to put the CPU to sleep when idle 192clkctrl0 at obio0 193 194## Mostek clock found on 4/300, sun4c, and sun4m systems. 195## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 196clock0 at obio0 # sun4m 197 198## Timer chip found on 4/300, sun4c, and sun4m systems. 199timer0 at obio0 # sun4m 200 201#### Serial port configuration 202 203## Zilog 8530 serial chips. Each has two-channels. 204## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 205zs0 at obio0 # sun4m 206zstty0 at zs0 channel 0 # ttya 207zstty1 at zs0 channel 1 # ttyb 208 209zs1 at obio0 # sun4m 210zstty* at zs1 channel ? # mouse/keyboard 211 212kbd0 at zstty? 213ms0 at zstty? 214 215wskbd* at kbd? console ? 216wsmouse* at ms? 217 218## Tadpole 3GX/3XL have a builtin modem that emulates a NS16450. 219com* at obio0 # sun4m (tadpole) 220 221## PCMCIA serial interfaces 222com* at pcmcia? 223pcmcom* at pcmcia? 224com* at pcmcom? 225 226#### Disk controllers and disks 227 228# 229 230## The following flags may be set for the NCR53c94 based esp driver: 231## bits 0-7: disable disconnect/reselect for the corresponding target 232## bits 8-15: disable synchronous negotiation for target [bit-8] 233 234## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 235## Both `dma' and `esp' are needed in all cases. 236## Two kinds of additional SBus SCSI interfaces are available. One uses 237## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 238 239## sun4/300 SCSI - an NCR53c94 or equivalent behind 240## an LSI Logic DMA controller 241 242dma0 at sbus0 slot ? offset ? # sun4c/sun4m 243esp0 at dma0 flags 0x0000 # sun4m 244 245scsibus* at esp? 246 247## PCMCIA SCSI controllers 248#aic* at pcmcia? 249#scsibus* at aic? 250 251## These entries find devices on all SCSI busses and assign 252## unit numbers dynamically. 253sd* at scsibus? target ? lun ? # SCSI disks 254st* at scsibus? target ? lun ? # SCSI tapes 255cd* at scsibus? target ? lun ? # SCSI CD-ROMs 256ch* at scsibus? target ? lun ? # SCSI changer devices 257ss* at scsibus? target ? lun ? # SCSI scanners 258uk* at scsibus? target ? lun ? # unknown SCSI 259 260## PCMCIA IDE controllers 261wdc* at pcmcia? 262 263atabus* at ata? 264wd* at atabus? drive ? flags 0x0000 265 266## A disk-like interface to files. Can be used to create floppy, CD, 267## miniroot images, etc. 268 269pseudo-device vnd 270 271## Memory disk device, used on boot floppies with compressed 272## kernel-plus-root-disk images. 273 274#pseudo-device md 275 276 277#### Network interfaces 278 279## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 280## Three flavors of additional SBus ethernets are available. One attaches 281## directly like the sun4c on-board, one uses the ledma device like the 282## sun4m on-board, and one uses the lebuffer device. 283 284ledma0 at sbus0 slot ? offset ? # sun4m on-board 285le0 at ledma0 # sun4m on-board 286 287# PCMCIA ethernet devices 288ep* at pcmcia? 289#mbe* at pcmcia? 290#ne* at pcmcia? 291#sm* at pcmcia? 292 293wi* at pcmcia? 294 295## Loopback network interface; required 296pseudo-device loop 297 298## PPP, the successor to SLIP. See pppd(8). 299pseudo-device ppp 300 301## Network "tunnel" device, allowing protocol stacks to run in the userland. 302## This is used by the third-party user-mode "ppp" program, and others. 303pseudo-device tun 304 305## Generic L3 over IP tunnel 306#pseudo-device gre # generic L3 over IP tunnel 307 308## Berkeley Packet Filter, required to run RARPD. A generic C-language 309## interface that allows selective examining of incoming packets. 310pseudo-device bpfilter 311 312pseudo-device npf # NPF packet filter 313 314 315#### Audio and video devices 316 317## /dev/audio support 318 319#options DBRI_DEBUG # noisy debug output from the dbri driver 320dbri0 at sbus0 slot ? offset ? # SUNW,DBRI[s3|e] 321audio* at audiobus? 322 323spkr* at audio? # PC speaker (synthesized) 324 325# Tadpole 3GX/3GS (P9100 -- P Nine One Zero Zero -> pnozz) 326pnozz0 at sbus? slot ? offset ? 327#options PNOZZ_EMUL_CG3 # emulate a CG3 for Xsun instead of 328 # running natively 329 330wsdisplay* at wsemuldisplaydev? console ? 331 332#### Other device configuration 333 334# Tadpole microcontroller 335tctrl0 at obio0 336 337## Pseudo ttys, required for network logins and programs like screen. 338 339pseudo-device pty # pseudo-ttys (for network, etc.) 340 341## Random device, used to implement /dev/random (a source of random noise), 342## and generate randomness for some kernel formulae. 343 344 345pseudo-device clockctl # user control of clock subsystem 346pseudo-device drvctl # user control of drive subsystem 347#pseudo-device fss # file system snapshot device 348 349pseudo-device wsmux # mouse and keyboard multiplexor 350pseudo-device wsfont 351