GENERIC revision 1.104
1# $NetBSD: GENERIC,v 1.104 2020/03/25 17:06:19 jdolecek Exp $ 2# 3# machine description file for GENERIC NAS 4# 5# This machine description file is used to generate the default NetBSD 6# kernel. The generic kernel does not include all options, subsystems 7# and device drivers, but should be useful for most applications. 8# 9# The machine description file can be customised for your specific 10# machine to reduce the kernel size and improve its performance. 11# 12# For further information on compiling NetBSD kernels, see the config(8) 13# man page. 14# 15# For further information on hardware support for this architecture, see 16# the intro(4) man page. For further information about kernel options 17# for this architecture, see the options(4) man page. For an explanation 18# of each device driver in this file see the section 4 man page for the 19# device. 20 21include "arch/sandpoint/conf/std.sandpoint" 22 23options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25#ident "GENERIC-$Revision: 1.104 $" 26 27maxusers 32 28 29#options ALTIVEC # Include AltiVec support 30 31# Standard system options 32#options INSECURE # disable kernel security levels 33 34options RTC_OFFSET=0 # hardware clock is this many mins. west of GMT 35options KTRACE 36 37options SYSVMSG # System V message queues 38options SYSVSEM # System V semaphores 39options SYSVSHM # System V shared memory 40 41#options MODULAR # module(7) support 42#options MODULAR_DEFAULT_AUTOLOAD 43#options USERCONF # userconf(4) support 44 45#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 46options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 47 48# Alternate buffer queue strategies for better responsiveness under high 49# disk I/O load. 50#options BUFQ_READPRIO 51options BUFQ_PRIOCSCAN 52 53# Diagnostic/debugging support options 54#options DIAGNOSTIC # cheap kernel consistency checks 55#options DEBUG # expensive debugging checks/support 56options DDB 57#options DDB_HISTORY_SIZE=100 # Enable history editing in DDB 58#options TRAP_PANICWAIT 59#options PMAPCHECK 60#options PMAPDEBUG 61options MSGBUFSIZE=65536 62 63#makeoptions DEBUG="-g" 64 65# Compatibility options 66include "conf/compat_netbsd09.config" 67options COMPAT_NOMID # NetBSD 0.8, 386BSD, and BSDI 68#options COMPAT_386BSD_MBRPART # recognize old partition ID 69#options COMPAT_LINUX # binary compatibility with Linux 70 71# Wedge support 72options DKWEDGE_AUTODISCOVER # Automatically add dk(4) instances 73options DKWEDGE_METHOD_GPT # Supports GPT partitions as wedges 74#options DKWEDGE_METHOD_BSDLABEL # Support disklabel entries as wedges 75#options DKWEDGE_METHOD_MBR # Support MBR partitions as wedges 76options DKWEDGE_METHOD_APPLE # Support Apple partitions as wedges 77#options DKWEDGE_METHOD_RDB # Support RDB partitions as wedges 78 79# File systems 80file-system FFS # UFS 81file-system EXT2FS # second extended file system (linux) 82#file-system LFS # log-structured file system 83file-system MFS # memory file system 84file-system NFS # Network File System client 85#file-system NTFS # Windows/NT file system (experimental) 86file-system CD9660 # ISO 9660 + Rock Ridge file system 87file-system MSDOSFS # MS-DOS file system 88file-system FDESC # /dev/fd 89file-system KERNFS # /kern 90file-system NULLFS # loopback file system 91#file-system OVERLAY # overlay file system 92file-system PROCFS # /proc 93#file-system UMAPFS # NULLFS + uid and gid remapping 94#file-system UNION # union file system 95#file-system CODA # Coda File System; also needs vcoda (below) 96file-system PTYFS # /dev/ptm support 97file-system TMPFS # Efficient memory file-system 98 99# File system options 100options QUOTA # legacy UFS quotas 101options QUOTA2 # new, in-filesystem UFS quotas 102#options DISKLABEL_EI # disklabel Endian Independent support 103#options FFS_EI # FFS Endian Independent support 104options WAPBL # File system journaling support 105options NFSSERVER # Network File System server 106#options FFS_NO_SNAPSHOT # No FFS snapshot support 107options UFS_EXTATTR # Extended attribute support for UFS1 108#options EXT2FS_SYSTEM_FLAGS # makes ext2fs file flags (append and 109 110#options NFS_BOOT_DHCP 111options NFS_BOOT_BOOTPARAM,NFS_BOOT_BOOTP 112 113# Networking options 114#options GATEWAY # packet forwarding 115options INET # IP + ICMP + TCP + UDP 116options INET6 # IPV6 117#options IPSEC # IP security 118#options IPSEC_DEBUG # debug for IP security 119#options MROUTING # IP multicast routing 120#options PIM # Protocol Independent Multicast 121#options NETATALK # AppleTalk networking protocols 122#options PPP_BSDCOMP # BSD-Compress compression support for PPP 123#options PPP_DEFLATE # Deflate compression support for PPP 124#options PPP_FILTER # Active filter support for PPP (requires BPF) 125#options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 126 127#options ALTQ # Manipulate network interfaces' output queues 128#options ALTQ_BLUE # Stochastic Fair Blue 129#options ALTQ_CBQ # Class-Based Queueing 130#options ALTQ_CDNR # Diffserv Traffic Conditioner 131#options ALTQ_FIFOQ # First-In First-Out Queue 132#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 133#options ALTQ_HFSC # Hierarchical Fair Service Curve 134#options ALTQ_LOCALQ # Local queueing discipline 135#options ALTQ_PRIQ # Priority Queueing 136#options ALTQ_RED # Random Early Detection 137#options ALTQ_RIO # RED with IN/OUT 138#options ALTQ_WFQ # Weighted Fair Queueing 139 140# These options enable verbose messages for several subsystems. 141# Warning, these may compile large string tables into the kernel! 142#options PCIVERBOSE # verbose PCI device autoconfig messages 143#options MIIVERBOSE # verbose PHY autoconfig messages 144#options PCI_CONFIG_DUMP # verbosely dump PCI config space 145#options SCSIVERBOSE # human readable SCSI error messages 146#options USBVERBOSE # verbose USB device autoconfig messages 147 148# Kernel root file system and dump configuration 149config netbsd root on ? type ? 150 151# 152# Device configuration 153# 154mainbus0 at root 155cpu* at mainbus0 156 157#cfi0 at mainbus0 158#nor* at cfi? 159#flash* at nor? 160 161nhpow0 at mainbus0 # NH230/231 power,LED,buttons 162 163#options PCI_NETBSD_CONFIGURE 164pci* at mainbus0 bus ? 165pchb* at pci? dev ? function ? # PCI host bridge 166 167eumb* at mainbus0 168com0 at eumb? unit 0 # console at 0x4500 169#com1 at eumb? unit 1 170satmgr0 at eumb? unit 1 # satmgr at 0x4600 171ociic* at eumb? 172iic* at ociic? 173lmtemp* at iic? addr 0x48 # LM75 temperature sensor 174rs5c372rtc* at iic? addr 0x32 175s390rtc* at iic? addr 0x30 176pcf8563rtc* at iic? addr 0x51 177dsrtc* at iic? addr 0x68 178strtc* at iic? addr 0x68 # ST M41T80 (or compat) RTC 179 180# PCI IDE controllers - see pciide(4) for supported hardware. 181acardide* at pci? dev ? function ? # Acard IDE controllers 182cmdide* at pci? dev ? function ? # CMD tech IDE controllers 183iteide* at pci? dev ? function ? # IT Express IDE controllers 184satalink* at pci? dev ? function ? # SiI SATALink controllers 185viaide* at pci? dev ? function ? # VIA IDE controllers 186 187# ATA (IDE) bus support 188atabus* at ata? 189 190# IDE drives 191# Flags are used only with controllers that support DMA operations 192# and mode settings (e.g. some pciide controllers) 193# The lowest order four bits (rightmost digit) of the flags define the PIO 194# mode to use, the next set of four bits the DMA mode and the third set the 195# UltraDMA mode. For each set of four bits, the 3 lower bits define the mode 196# to use, and the last bit must be 1 for this setting to be used. 197# For DMA and UDMA, 0xf (1111) means 'disable'. 198# 0x0fac means 'use PIO mode 4, DMA mode 2, disable UltraDMA'. 199# (0xc=1100, 0xa=1010, 0xf=1111) 200# 0x0000 means "use whatever the drive claims to support". 201wd* at atabus? drive ? flags 0x0000 202 203# ATAPI bus support 204atapibus* at atapi? 205 206# ATAPI devices 207# flags have the same meaning as for IDE drives. 208cd* at atapibus? drive ? flags 0x0000 # ATAPI CD-ROM drives 209sd* at atapibus? drive ? flags 0x0000 # ATAPI disk drives 210uk* at atapibus? drive ? flags 0x0000 # ATAPI unknown 211 212# PCI network interfaces 213ral* at pci? dev ? function ? # Ralink Technology RT25x0 802.11a/b/g 214re* at pci? dev ? function ? # Realtek 8139C+/8169/8169S/8110S 215skc* at pci? dev ? function ? # Marvell Yukon Gigabit Ethernet 216sk* at skc? # Marvell Yukon Gigabit Ethernet 217stge* at pci? dev ? function ? # Sundance ST1023 Gigabit 218tlp* at pci? dev ? function ? # DEC Tulip and similar 219wm* at pci? dev ? function ? # Intel 8254x Gigabit Ethernet 220 221inphy* at mii? phy ? # Intel 82555 PHYs 222nsphy* at mii? phy ? # NS83840 PHYs 223rgephy* at mii? phy ? # Realtek 8169S/8110S internal PHYs 224makphy* at mii? phy ? # Marvell Semiconductor 88E1000 PHYs 225ukphy* at mii? phy ? # generic unknown PHYs 226 227# GPIO devices 228gpio* at gpiobus? 229 230# USB Controller and Devices 231ehci* at pci? dev ? function ? # Enhanced Host Controller 232ohci* at pci? dev ? function ? # Open Host Controller 233 234# USB bus support 235usb* at ehci? 236usb* at ohci? 237 238# USB Hubs 239uhub* at usb? 240uhub* at uhub? port ? 241 242# USB HID devices 243uhidev* at uhub? port ? configuration ? interface ? # USB HID device 244uthum* at uhidev? reportid ? # TEMPerHUM sensors 245uhid* at uhidev? reportid ? # USB Generic HID 246 247# USB video 248uvideo* at uhub? # USB Video Class capture devices 249video* at videobus? 250 251# USB printer 252ulpt* at uhub? port ? configuration ? interface ? 253 254# USB Mass Storage 255umass* at uhub? port ? configuration ? interface ? 256 257# USB scanners 258#uscanner* at uhub? port ? 259ugen* at uhub? port ? configuration ? interface ? # USB Generic driver 260 261# SCSI bus support 262scsibus* at umass? 263 264# SCSI devices 265sd* at scsibus? target ? lun ? # SCSI disk drives 266cd* at scsibus? target ? lun ? # SCSI CD-ROM drives 267 268 269# 270# Pseudo-Devices 271# 272#pseudo-device crypto # /dev/crypto device 273#pseudo-device swcrypto # software crypto implementation 274 275# disk/mass storage pseudo-devices 276#pseudo-device ccd # concatenated/striped disk devices 277#pseudo-device cgd # cryptographic disk devices 278pseudo-device fss # file system snapshot device 279#pseudo-device putter # for puffs and pud 280 281pseudo-device raid # RAIDframe disk driver 282options RAID_AUTOCONFIG # auto-configuration of RAID components 283# Options to enable various other RAIDframe RAID types. 284#options RF_INCLUDE_EVENODD=1 285#options RF_INCLUDE_RAID5_RS=1 286#options RF_INCLUDE_PARITYLOGGING=1 287#options RF_INCLUDE_CHAINDECLUSTER=1 288#options RF_INCLUDE_INTERDECLUSTER=1 289#options RF_INCLUDE_PARITY_DECLUSTERING=1 290#options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 291 292pseudo-device vnd 293#options VND_COMPRESSION # compressed vnd(4) 294 295# network pseudo-devices 296pseudo-device loop 297pseudo-device bpfilter # packet filter 298pseudo-device carp # Common Address Redundancy Protocol 299#pseudo-device ppp # Point-to-Point Protocol 300#pseudo-device pppoe # PPP over Ethernet (RFC 2516) 301#pseudo-device npf # NPF packet filter 302#pseudo-device sl # Serial Line IP 303#pseudo-device tun # network tunneling over tty 304#pseudo-device tap # virtual Ethernet 305#pseudo-device gre # generic L3 over IP tunnel 306#pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 307#pseudo-device faith # IPv[46] tcp relay translation i/f 308#pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 309#pseudo-device vlan # IEEE 802.1q encapsulation 310#pseudo-device bridge # simple inter-network bridging 311#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 312#pseudo-device agr # IEEE 802.3ad link aggregation 313 314# 315# accept filters 316#pseudo-device accf_data # "dataready" accept filter 317#pseudo-device accf_http # "httpready" accept filter 318 319# miscellaneous pseudo-devices 320pseudo-device pty 321pseudo-device clockctl # user control of clock subsystem 322pseudo-device ksyms # /dev/ksyms 323#pseudo-device lockstat # lock profiling 324 325# a pseudo device needed for Coda # also needs CODA (above) 326#pseudo-device vcoda # coda minicache <-> venus comm. 327 328# userland interface to drivers, including autoconf and properties retrieval 329pseudo-device drvctl 330 331include "dev/veriexec.config" 332 333#options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 334#options PAX_ASLR=0 # PaX Address Space Layout Randomization 335