1// SPDX-License-Identifier: GPL-2.0-or-later 2/* 3 * ALSA driver for ICEnsemble VT1724 (Envy24HT) 4 * 5 * Lowlevel functions for ESI Juli@ cards 6 * 7 * Copyright (c) 2004 Jaroslav Kysela <perex@perex.cz> 8 * 2008 Pavel Hofman <dustin@seznam.cz> 9 */ 10 11#include <linux/delay.h> 12#include <linux/interrupt.h> 13#include <linux/init.h> 14#include <linux/slab.h> 15#include <linux/string.h> 16#include <sound/core.h> 17#include <sound/tlv.h> 18 19#include "ice1712.h" 20#include "envy24ht.h" 21#include "juli.h" 22 23struct juli_spec { 24 struct ak4114 *ak4114; 25 unsigned int analog:1; 26}; 27 28/* 29 * chip addresses on I2C bus 30 */ 31#define AK4114_ADDR 0x20 /* S/PDIF receiver */ 32#define AK4358_ADDR 0x22 /* DAC */ 33 34/* 35 * Juli does not use the standard ICE1724 clock scheme. Juli's ice1724 chip is 36 * supplied by external clock provided by Xilinx array and MK73-1 PLL frequency 37 * multiplier. Actual frequency is set by ice1724 GPIOs hooked to the Xilinx. 38 * 39 * The clock circuitry is supplied by the two ice1724 crystals. This 40 * arrangement allows to generate independent clock signal for AK4114's input 41 * rate detection circuit. As a result, Juli, unlike most other 42 * ice1724+ak4114-based cards, detects spdif input rate correctly. 43 * This fact is applied in the driver, allowing to modify PCM stream rate 44 * parameter according to the actual input rate. 45 * 46 * Juli uses the remaining three stereo-channels of its DAC to optionally 47 * monitor analog input, digital input, and digital output. The corresponding 48 * I2S signals are routed by Xilinx, controlled by GPIOs. 49 * 50 * The master mute is implemented using output muting transistors (GPIO) in 51 * combination with smuting the DAC. 52 * 53 * The card itself has no HW master volume control, implemented using the 54 * vmaster control. 55 * 56 * TODO: 57 * researching and fixing the input monitors 58 */ 59 60/* 61 * GPIO pins 62 */ 63#define GPIO_FREQ_MASK (3<<0) 64#define GPIO_FREQ_32KHZ (0<<0) 65#define GPIO_FREQ_44KHZ (1<<0) 66#define GPIO_FREQ_48KHZ (2<<0) 67#define GPIO_MULTI_MASK (3<<2) 68#define GPIO_MULTI_4X (0<<2) 69#define GPIO_MULTI_2X (1<<2) 70#define GPIO_MULTI_1X (2<<2) /* also external */ 71#define GPIO_MULTI_HALF (3<<2) 72#define GPIO_INTERNAL_CLOCK (1<<4) /* 0 = external, 1 = internal */ 73#define GPIO_CLOCK_MASK (1<<4) 74#define GPIO_ANALOG_PRESENT (1<<5) /* RO only: 0 = present */ 75#define GPIO_RXMCLK_SEL (1<<7) /* must be 0 */ 76#define GPIO_AK5385A_CKS0 (1<<8) 77#define GPIO_AK5385A_DFS1 (1<<9) 78#define GPIO_AK5385A_DFS0 (1<<10) 79#define GPIO_DIGOUT_MONITOR (1<<11) /* 1 = active */ 80#define GPIO_DIGIN_MONITOR (1<<12) /* 1 = active */ 81#define GPIO_ANAIN_MONITOR (1<<13) /* 1 = active */ 82#define GPIO_AK5385A_CKS1 (1<<14) /* must be 0 */ 83#define GPIO_MUTE_CONTROL (1<<15) /* output mute, 1 = muted */ 84 85#define GPIO_RATE_MASK (GPIO_FREQ_MASK | GPIO_MULTI_MASK | \ 86 GPIO_CLOCK_MASK) 87#define GPIO_AK5385A_MASK (GPIO_AK5385A_CKS0 | GPIO_AK5385A_DFS0 | \ 88 GPIO_AK5385A_DFS1 | GPIO_AK5385A_CKS1) 89 90#define JULI_PCM_RATE (SNDRV_PCM_RATE_16000 | SNDRV_PCM_RATE_22050 | \ 91 SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 | \ 92 SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_64000 | \ 93 SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000 | \ 94 SNDRV_PCM_RATE_176400 | SNDRV_PCM_RATE_192000) 95 96#define GPIO_RATE_16000 (GPIO_FREQ_32KHZ | GPIO_MULTI_HALF | \ 97 GPIO_INTERNAL_CLOCK) 98#define GPIO_RATE_22050 (GPIO_FREQ_44KHZ | GPIO_MULTI_HALF | \ 99 GPIO_INTERNAL_CLOCK) 100#define GPIO_RATE_24000 (GPIO_FREQ_48KHZ | GPIO_MULTI_HALF | \ 101 GPIO_INTERNAL_CLOCK) 102#define GPIO_RATE_32000 (GPIO_FREQ_32KHZ | GPIO_MULTI_1X | \ 103 GPIO_INTERNAL_CLOCK) 104#define GPIO_RATE_44100 (GPIO_FREQ_44KHZ | GPIO_MULTI_1X | \ 105 GPIO_INTERNAL_CLOCK) 106#define GPIO_RATE_48000 (GPIO_FREQ_48KHZ | GPIO_MULTI_1X | \ 107 GPIO_INTERNAL_CLOCK) 108#define GPIO_RATE_64000 (GPIO_FREQ_32KHZ | GPIO_MULTI_2X | \ 109 GPIO_INTERNAL_CLOCK) 110#define GPIO_RATE_88200 (GPIO_FREQ_44KHZ | GPIO_MULTI_2X | \ 111 GPIO_INTERNAL_CLOCK) 112#define GPIO_RATE_96000 (GPIO_FREQ_48KHZ | GPIO_MULTI_2X | \ 113 GPIO_INTERNAL_CLOCK) 114#define GPIO_RATE_176400 (GPIO_FREQ_44KHZ | GPIO_MULTI_4X | \ 115 GPIO_INTERNAL_CLOCK) 116#define GPIO_RATE_192000 (GPIO_FREQ_48KHZ | GPIO_MULTI_4X | \ 117 GPIO_INTERNAL_CLOCK) 118 119/* 120 * Initial setup of the conversion array GPIO <-> rate 121 */ 122static const unsigned int juli_rates[] = { 123 16000, 22050, 24000, 32000, 124 44100, 48000, 64000, 88200, 125 96000, 176400, 192000, 126}; 127 128static const unsigned int gpio_vals[] = { 129 GPIO_RATE_16000, GPIO_RATE_22050, GPIO_RATE_24000, GPIO_RATE_32000, 130 GPIO_RATE_44100, GPIO_RATE_48000, GPIO_RATE_64000, GPIO_RATE_88200, 131 GPIO_RATE_96000, GPIO_RATE_176400, GPIO_RATE_192000, 132}; 133 134static const struct snd_pcm_hw_constraint_list juli_rates_info = { 135 .count = ARRAY_SIZE(juli_rates), 136 .list = juli_rates, 137 .mask = 0, 138}; 139 140static int get_gpio_val(int rate) 141{ 142 int i; 143 for (i = 0; i < ARRAY_SIZE(juli_rates); i++) 144 if (juli_rates[i] == rate) 145 return gpio_vals[i]; 146 return 0; 147} 148 149static void juli_ak4114_write(void *private_data, unsigned char reg, 150 unsigned char val) 151{ 152 snd_vt1724_write_i2c((struct snd_ice1712 *)private_data, AK4114_ADDR, 153 reg, val); 154} 155 156static unsigned char juli_ak4114_read(void *private_data, unsigned char reg) 157{ 158 return snd_vt1724_read_i2c((struct snd_ice1712 *)private_data, 159 AK4114_ADDR, reg); 160} 161 162/* 163 * If SPDIF capture and slaved to SPDIF-IN, setting runtime rate 164 * to the external rate 165 */ 166static void juli_spdif_in_open(struct snd_ice1712 *ice, 167 struct snd_pcm_substream *substream) 168{ 169 struct juli_spec *spec = ice->spec; 170 struct snd_pcm_runtime *runtime = substream->runtime; 171 int rate; 172 173 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK || 174 !ice->is_spdif_master(ice)) 175 return; 176 rate = snd_ak4114_external_rate(spec->ak4114); 177 if (rate >= runtime->hw.rate_min && rate <= runtime->hw.rate_max) { 178 runtime->hw.rate_min = rate; 179 runtime->hw.rate_max = rate; 180 } 181} 182 183/* 184 * AK4358 section 185 */ 186 187static void juli_akm_lock(struct snd_akm4xxx *ak, int chip) 188{ 189} 190 191static void juli_akm_unlock(struct snd_akm4xxx *ak, int chip) 192{ 193} 194 195static void juli_akm_write(struct snd_akm4xxx *ak, int chip, 196 unsigned char addr, unsigned char data) 197{ 198 struct snd_ice1712 *ice = ak->private_data[0]; 199 200 if (snd_BUG_ON(chip)) 201 return; 202 snd_vt1724_write_i2c(ice, AK4358_ADDR, addr, data); 203} 204 205/* 206 * change the rate of envy24HT, AK4358, AK5385 207 */ 208static void juli_akm_set_rate_val(struct snd_akm4xxx *ak, unsigned int rate) 209{ 210 unsigned char old, tmp, ak4358_dfs; 211 unsigned int ak5385_pins, old_gpio, new_gpio; 212 struct snd_ice1712 *ice = ak->private_data[0]; 213 struct juli_spec *spec = ice->spec; 214 215 if (rate == 0) /* no hint - S/PDIF input is master or the new spdif 216 input rate undetected, simply return */ 217 return; 218 219 /* adjust DFS on codecs */ 220 if (rate > 96000) { 221 ak4358_dfs = 2; 222 ak5385_pins = GPIO_AK5385A_DFS1 | GPIO_AK5385A_CKS0; 223 } else if (rate > 48000) { 224 ak4358_dfs = 1; 225 ak5385_pins = GPIO_AK5385A_DFS0; 226 } else { 227 ak4358_dfs = 0; 228 ak5385_pins = 0; 229 } 230 /* AK5385 first, since it requires cold reset affecting both codecs */ 231 old_gpio = ice->gpio.get_data(ice); 232 new_gpio = (old_gpio & ~GPIO_AK5385A_MASK) | ak5385_pins; 233 /* dev_dbg(ice->card->dev, "JULI - ak5385 set_rate_val: new gpio 0x%x\n", 234 new_gpio); */ 235 ice->gpio.set_data(ice, new_gpio); 236 237 /* cold reset */ 238 old = inb(ICEMT1724(ice, AC97_CMD)); 239 outb(old | VT1724_AC97_COLD, ICEMT1724(ice, AC97_CMD)); 240 udelay(1); 241 outb(old & ~VT1724_AC97_COLD, ICEMT1724(ice, AC97_CMD)); 242 243 /* AK4358 */ 244 /* set new value, reset DFS */ 245 tmp = snd_akm4xxx_get(ak, 0, 2); 246 snd_akm4xxx_reset(ak, 1); 247 tmp = snd_akm4xxx_get(ak, 0, 2); 248 tmp &= ~(0x03 << 4); 249 tmp |= ak4358_dfs << 4; 250 snd_akm4xxx_set(ak, 0, 2, tmp); 251 snd_akm4xxx_reset(ak, 0); 252 253 /* reinit ak4114 */ 254 snd_ak4114_reinit(spec->ak4114); 255} 256 257#define AK_DAC(xname, xch) { .name = xname, .num_channels = xch } 258#define PCM_VOLUME "PCM Playback Volume" 259#define MONITOR_AN_IN_VOLUME "Monitor Analog In Volume" 260#define MONITOR_DIG_IN_VOLUME "Monitor Digital In Volume" 261#define MONITOR_DIG_OUT_VOLUME "Monitor Digital Out Volume" 262 263static const struct snd_akm4xxx_dac_channel juli_dac[] = { 264 AK_DAC(PCM_VOLUME, 2), 265 AK_DAC(MONITOR_AN_IN_VOLUME, 2), 266 AK_DAC(MONITOR_DIG_OUT_VOLUME, 2), 267 AK_DAC(MONITOR_DIG_IN_VOLUME, 2), 268}; 269 270 271static const struct snd_akm4xxx akm_juli_dac = { 272 .type = SND_AK4358, 273 .num_dacs = 8, /* DAC1 - analog out 274 DAC2 - analog in monitor 275 DAC3 - digital out monitor 276 DAC4 - digital in monitor 277 */ 278 .ops = { 279 .lock = juli_akm_lock, 280 .unlock = juli_akm_unlock, 281 .write = juli_akm_write, 282 .set_rate_val = juli_akm_set_rate_val 283 }, 284 .dac_info = juli_dac, 285}; 286 287#define juli_mute_info snd_ctl_boolean_mono_info 288 289static int juli_mute_get(struct snd_kcontrol *kcontrol, 290 struct snd_ctl_elem_value *ucontrol) 291{ 292 struct snd_ice1712 *ice = snd_kcontrol_chip(kcontrol); 293 unsigned int val; 294 val = ice->gpio.get_data(ice) & (unsigned int) kcontrol->private_value; 295 if (kcontrol->private_value == GPIO_MUTE_CONTROL) 296 /* val 0 = signal on */ 297 ucontrol->value.integer.value[0] = (val) ? 0 : 1; 298 else 299 /* val 1 = signal on */ 300 ucontrol->value.integer.value[0] = (val) ? 1 : 0; 301 return 0; 302} 303 304static int juli_mute_put(struct snd_kcontrol *kcontrol, 305 struct snd_ctl_elem_value *ucontrol) 306{ 307 struct snd_ice1712 *ice = snd_kcontrol_chip(kcontrol); 308 unsigned int old_gpio, new_gpio; 309 old_gpio = ice->gpio.get_data(ice); 310 if (ucontrol->value.integer.value[0]) { 311 /* unmute */ 312 if (kcontrol->private_value == GPIO_MUTE_CONTROL) { 313 /* 0 = signal on */ 314 new_gpio = old_gpio & ~GPIO_MUTE_CONTROL; 315 /* un-smuting DAC */ 316 snd_akm4xxx_write(ice->akm, 0, 0x01, 0x01); 317 } else 318 /* 1 = signal on */ 319 new_gpio = old_gpio | 320 (unsigned int) kcontrol->private_value; 321 } else { 322 /* mute */ 323 if (kcontrol->private_value == GPIO_MUTE_CONTROL) { 324 /* 1 = signal off */ 325 new_gpio = old_gpio | GPIO_MUTE_CONTROL; 326 /* smuting DAC */ 327 snd_akm4xxx_write(ice->akm, 0, 0x01, 0x03); 328 } else 329 /* 0 = signal off */ 330 new_gpio = old_gpio & 331 ~((unsigned int) kcontrol->private_value); 332 } 333 /* dev_dbg(ice->card->dev, 334 "JULI - mute/unmute: control_value: 0x%x, old_gpio: 0x%x, " 335 "new_gpio 0x%x\n", 336 (unsigned int)ucontrol->value.integer.value[0], old_gpio, 337 new_gpio); */ 338 if (old_gpio != new_gpio) { 339 ice->gpio.set_data(ice, new_gpio); 340 return 1; 341 } 342 /* no change */ 343 return 0; 344} 345 346static const struct snd_kcontrol_new juli_mute_controls[] = { 347 { 348 .iface = SNDRV_CTL_ELEM_IFACE_MIXER, 349 .name = "Master Playback Switch", 350 .info = juli_mute_info, 351 .get = juli_mute_get, 352 .put = juli_mute_put, 353 .private_value = GPIO_MUTE_CONTROL, 354 }, 355 /* Although the following functionality respects the succint NDA'd 356 * documentation from the card manufacturer, and the same way of 357 * operation is coded in OSS Juli driver, only Digital Out monitor 358 * seems to work. Surprisingly, Analog input monitor outputs Digital 359 * output data. The two are independent, as enabling both doubles 360 * volume of the monitor sound. 361 * 362 * Checking traces on the board suggests the functionality described 363 * by the manufacturer is correct - I2S from ADC and AK4114 364 * go to ICE as well as to Xilinx, I2S inputs of DAC2,3,4 (the monitor 365 * inputs) are fed from Xilinx. 366 * 367 * I even checked traces on board and coded a support in driver for 368 * an alternative possibility - the unused I2S ICE output channels 369 * switched to HW-IN/SPDIF-IN and providing the monitoring signal to 370 * the DAC - to no avail. The I2S outputs seem to be unconnected. 371 * 372 * The windows driver supports the monitoring correctly. 373 */ 374 { 375 .iface = SNDRV_CTL_ELEM_IFACE_MIXER, 376 .name = "Monitor Analog In Switch", 377 .info = juli_mute_info, 378 .get = juli_mute_get, 379 .put = juli_mute_put, 380 .private_value = GPIO_ANAIN_MONITOR, 381 }, 382 { 383 .iface = SNDRV_CTL_ELEM_IFACE_MIXER, 384 .name = "Monitor Digital Out Switch", 385 .info = juli_mute_info, 386 .get = juli_mute_get, 387 .put = juli_mute_put, 388 .private_value = GPIO_DIGOUT_MONITOR, 389 }, 390 { 391 .iface = SNDRV_CTL_ELEM_IFACE_MIXER, 392 .name = "Monitor Digital In Switch", 393 .info = juli_mute_info, 394 .get = juli_mute_get, 395 .put = juli_mute_put, 396 .private_value = GPIO_DIGIN_MONITOR, 397 }, 398}; 399 400static const char * const follower_vols[] = { 401 PCM_VOLUME, 402 MONITOR_AN_IN_VOLUME, 403 MONITOR_DIG_IN_VOLUME, 404 MONITOR_DIG_OUT_VOLUME, 405 NULL 406}; 407 408static 409DECLARE_TLV_DB_SCALE(juli_master_db_scale, -6350, 50, 1); 410 411static int juli_add_controls(struct snd_ice1712 *ice) 412{ 413 struct juli_spec *spec = ice->spec; 414 int err; 415 unsigned int i; 416 struct snd_kcontrol *vmaster; 417 418 err = snd_ice1712_akm4xxx_build_controls(ice); 419 if (err < 0) 420 return err; 421 422 for (i = 0; i < ARRAY_SIZE(juli_mute_controls); i++) { 423 err = snd_ctl_add(ice->card, 424 snd_ctl_new1(&juli_mute_controls[i], ice)); 425 if (err < 0) 426 return err; 427 } 428 /* Create virtual master control */ 429 vmaster = snd_ctl_make_virtual_master("Master Playback Volume", 430 juli_master_db_scale); 431 if (!vmaster) 432 return -ENOMEM; 433 err = snd_ctl_add(ice->card, vmaster); 434 if (err < 0) 435 return err; 436 err = snd_ctl_add_followers(ice->card, vmaster, follower_vols); 437 if (err < 0) 438 return err; 439 440 /* only capture SPDIF over AK4114 */ 441 return snd_ak4114_build(spec->ak4114, NULL, 442 ice->pcm->streams[SNDRV_PCM_STREAM_CAPTURE].substream); 443} 444 445/* 446 * suspend/resume 447 * */ 448 449#ifdef CONFIG_PM_SLEEP 450static int juli_resume(struct snd_ice1712 *ice) 451{ 452 struct snd_akm4xxx *ak = ice->akm; 453 struct juli_spec *spec = ice->spec; 454 /* akm4358 un-reset, un-mute */ 455 snd_akm4xxx_reset(ak, 0); 456 /* reinit ak4114 */ 457 snd_ak4114_resume(spec->ak4114); 458 return 0; 459} 460 461static int juli_suspend(struct snd_ice1712 *ice) 462{ 463 struct snd_akm4xxx *ak = ice->akm; 464 struct juli_spec *spec = ice->spec; 465 /* akm4358 reset and soft-mute */ 466 snd_akm4xxx_reset(ak, 1); 467 snd_ak4114_suspend(spec->ak4114); 468 return 0; 469} 470#endif 471 472/* 473 * initialize the chip 474 */ 475 476static inline int juli_is_spdif_master(struct snd_ice1712 *ice) 477{ 478 return (ice->gpio.get_data(ice) & GPIO_INTERNAL_CLOCK) ? 0 : 1; 479} 480 481static unsigned int juli_get_rate(struct snd_ice1712 *ice) 482{ 483 int i; 484 unsigned char result; 485 486 result = ice->gpio.get_data(ice) & GPIO_RATE_MASK; 487 for (i = 0; i < ARRAY_SIZE(gpio_vals); i++) 488 if (gpio_vals[i] == result) 489 return juli_rates[i]; 490 return 0; 491} 492 493/* setting new rate */ 494static void juli_set_rate(struct snd_ice1712 *ice, unsigned int rate) 495{ 496 unsigned int old, new; 497 unsigned char val; 498 499 old = ice->gpio.get_data(ice); 500 new = (old & ~GPIO_RATE_MASK) | get_gpio_val(rate); 501 /* dev_dbg(ice->card->dev, "JULI - set_rate: old %x, new %x\n", 502 old & GPIO_RATE_MASK, 503 new & GPIO_RATE_MASK); */ 504 505 ice->gpio.set_data(ice, new); 506 /* switching to external clock - supplied by external circuits */ 507 val = inb(ICEMT1724(ice, RATE)); 508 outb(val | VT1724_SPDIF_MASTER, ICEMT1724(ice, RATE)); 509} 510 511static inline unsigned char juli_set_mclk(struct snd_ice1712 *ice, 512 unsigned int rate) 513{ 514 /* no change in master clock */ 515 return 0; 516} 517 518/* setting clock to external - SPDIF */ 519static int juli_set_spdif_clock(struct snd_ice1712 *ice, int type) 520{ 521 unsigned int old; 522 old = ice->gpio.get_data(ice); 523 /* external clock (= 0), multiply 1x, 48kHz */ 524 ice->gpio.set_data(ice, (old & ~GPIO_RATE_MASK) | GPIO_MULTI_1X | 525 GPIO_FREQ_48KHZ); 526 return 0; 527} 528 529/* Called when ak4114 detects change in the input SPDIF stream */ 530static void juli_ak4114_change(struct ak4114 *ak4114, unsigned char c0, 531 unsigned char c1) 532{ 533 struct snd_ice1712 *ice = ak4114->change_callback_private; 534 int rate; 535 if (ice->is_spdif_master(ice) && c1) { 536 /* only for SPDIF master mode, rate was changed */ 537 rate = snd_ak4114_external_rate(ak4114); 538 /* dev_dbg(ice->card->dev, "ak4114 - input rate changed to %d\n", 539 rate); */ 540 juli_akm_set_rate_val(ice->akm, rate); 541 } 542} 543 544static int juli_init(struct snd_ice1712 *ice) 545{ 546 static const unsigned char ak4114_init_vals[] = { 547 /* AK4117_REG_PWRDN */ AK4114_RST | AK4114_PWN | 548 AK4114_OCKS0 | AK4114_OCKS1, 549 /* AK4114_REQ_FORMAT */ AK4114_DIF_I24I2S, 550 /* AK4114_REG_IO0 */ AK4114_TX1E, 551 /* AK4114_REG_IO1 */ AK4114_EFH_1024 | AK4114_DIT | 552 AK4114_IPS(1), 553 /* AK4114_REG_INT0_MASK */ 0, 554 /* AK4114_REG_INT1_MASK */ 0 555 }; 556 static const unsigned char ak4114_init_txcsb[] = { 557 0x41, 0x02, 0x2c, 0x00, 0x00 558 }; 559 int err; 560 struct juli_spec *spec; 561 struct snd_akm4xxx *ak; 562 563 spec = kzalloc(sizeof(*spec), GFP_KERNEL); 564 if (!spec) 565 return -ENOMEM; 566 ice->spec = spec; 567 568 err = snd_ak4114_create(ice->card, 569 juli_ak4114_read, 570 juli_ak4114_write, 571 ak4114_init_vals, ak4114_init_txcsb, 572 ice, &spec->ak4114); 573 if (err < 0) 574 return err; 575 /* callback for codecs rate setting */ 576 spec->ak4114->change_callback = juli_ak4114_change; 577 spec->ak4114->change_callback_private = ice; 578 /* AK4114 in Juli can detect external rate correctly */ 579 spec->ak4114->check_flags = 0; 580 581#if 0 582/* 583 * it seems that the analog doughter board detection does not work reliably, so 584 * force the analog flag; it should be very rare (if ever) to come at Juli@ 585 * used without the analog daughter board 586 */ 587 spec->analog = (ice->gpio.get_data(ice) & GPIO_ANALOG_PRESENT) ? 0 : 1; 588#else 589 spec->analog = 1; 590#endif 591 592 if (spec->analog) { 593 dev_info(ice->card->dev, "juli@: analog I/O detected\n"); 594 ice->num_total_dacs = 2; 595 ice->num_total_adcs = 2; 596 597 ice->akm = kzalloc(sizeof(struct snd_akm4xxx), GFP_KERNEL); 598 ak = ice->akm; 599 if (!ak) 600 return -ENOMEM; 601 ice->akm_codecs = 1; 602 err = snd_ice1712_akm4xxx_init(ak, &akm_juli_dac, NULL, ice); 603 if (err < 0) 604 return err; 605 } 606 607 /* juli is clocked by Xilinx array */ 608 ice->hw_rates = &juli_rates_info; 609 ice->is_spdif_master = juli_is_spdif_master; 610 ice->get_rate = juli_get_rate; 611 ice->set_rate = juli_set_rate; 612 ice->set_mclk = juli_set_mclk; 613 ice->set_spdif_clock = juli_set_spdif_clock; 614 615 ice->spdif.ops.open = juli_spdif_in_open; 616 617#ifdef CONFIG_PM_SLEEP 618 ice->pm_resume = juli_resume; 619 ice->pm_suspend = juli_suspend; 620 ice->pm_suspend_enabled = 1; 621#endif 622 623 return 0; 624} 625 626 627/* 628 * Juli@ boards don't provide the EEPROM data except for the vendor IDs. 629 * hence the driver needs to sets up it properly. 630 */ 631 632static const unsigned char juli_eeprom[] = { 633 [ICE_EEP2_SYSCONF] = 0x2b, /* clock 512, mpu401, 1xADC, 1xDACs, 634 SPDIF in */ 635 [ICE_EEP2_ACLINK] = 0x80, /* I2S */ 636 [ICE_EEP2_I2S] = 0xf8, /* vol, 96k, 24bit, 192k */ 637 [ICE_EEP2_SPDIF] = 0xc3, /* out-en, out-int, spdif-in */ 638 [ICE_EEP2_GPIO_DIR] = 0x9f, /* 5, 6:inputs; 7, 4-0 outputs*/ 639 [ICE_EEP2_GPIO_DIR1] = 0xff, 640 [ICE_EEP2_GPIO_DIR2] = 0x7f, 641 [ICE_EEP2_GPIO_MASK] = 0x60, /* 5, 6: locked; 7, 4-0 writable */ 642 [ICE_EEP2_GPIO_MASK1] = 0x00, /* 0-7 writable */ 643 [ICE_EEP2_GPIO_MASK2] = 0x7f, 644 [ICE_EEP2_GPIO_STATE] = GPIO_FREQ_48KHZ | GPIO_MULTI_1X | 645 GPIO_INTERNAL_CLOCK, /* internal clock, multiple 1x, 48kHz*/ 646 [ICE_EEP2_GPIO_STATE1] = 0x00, /* unmuted */ 647 [ICE_EEP2_GPIO_STATE2] = 0x00, 648}; 649 650/* entry point */ 651struct snd_ice1712_card_info snd_vt1724_juli_cards[] = { 652 { 653 .subvendor = VT1724_SUBDEVICE_JULI, 654 .name = "ESI Juli@", 655 .model = "juli", 656 .chip_init = juli_init, 657 .build_controls = juli_add_controls, 658 .eeprom_size = sizeof(juli_eeprom), 659 .eeprom_data = juli_eeprom, 660 }, 661 { } /* terminator */ 662}; 663