1/* SPDX-License-Identifier: GPL-2.0+ */
2/*
3 * max8997.h - Driver for the Maxim 8997/8966
4 *
5 *  Copyright (C) 2009-2010 Samsung Electrnoics
6 *  MyungJoo Ham <myungjoo.ham@samsung.com>
7 *
8 * This driver is based on max8998.h
9 *
10 * MAX8997 has PMIC, MUIC, HAPTIC, RTC, FLASH, and Fuel Gauge devices.
11 * Except Fuel Gauge, every device shares the same I2C bus and included in
12 * this mfd driver. Although the fuel gauge is included in the chip, it is
13 * excluded from the driver because a) it has a different I2C bus from
14 * others and b) it can be enabled simply by using MAX17042 driver.
15 */
16
17#ifndef __LINUX_MFD_MAX8997_H
18#define __LINUX_MFD_MAX8997_H
19
20#include <linux/regulator/consumer.h>
21
22/* MAX8997/8966 regulator IDs */
23enum max8997_regulators {
24	MAX8997_LDO1 = 0,
25	MAX8997_LDO2,
26	MAX8997_LDO3,
27	MAX8997_LDO4,
28	MAX8997_LDO5,
29	MAX8997_LDO6,
30	MAX8997_LDO7,
31	MAX8997_LDO8,
32	MAX8997_LDO9,
33	MAX8997_LDO10,
34	MAX8997_LDO11,
35	MAX8997_LDO12,
36	MAX8997_LDO13,
37	MAX8997_LDO14,
38	MAX8997_LDO15,
39	MAX8997_LDO16,
40	MAX8997_LDO17,
41	MAX8997_LDO18,
42	MAX8997_LDO21,
43	MAX8997_BUCK1,
44	MAX8997_BUCK2,
45	MAX8997_BUCK3,
46	MAX8997_BUCK4,
47	MAX8997_BUCK5,
48	MAX8997_BUCK6,
49	MAX8997_BUCK7,
50	MAX8997_EN32KHZ_AP,
51	MAX8997_EN32KHZ_CP,
52	MAX8997_ENVICHG,
53	MAX8997_ESAFEOUT1,
54	MAX8997_ESAFEOUT2,
55	MAX8997_CHARGER_CV, /* control MBCCV of MBCCTRL3 */
56	MAX8997_CHARGER, /* charger current, MBCCTRL4 */
57	MAX8997_CHARGER_TOPOFF, /* MBCCTRL5 */
58
59	MAX8997_REG_MAX,
60};
61
62struct max8997_regulator_data {
63	int id;
64	struct regulator_init_data *initdata;
65	struct device_node *reg_node;
66};
67
68struct max8997_muic_reg_data {
69	u8 addr;
70	u8 data;
71};
72
73/**
74 * struct max8997_muic_platform_data
75 * @init_data: array of max8997_muic_reg_data
76 *	       used for initializing registers of MAX8997 MUIC device
77 * @num_init_data: array size of init_data
78 */
79struct max8997_muic_platform_data {
80	struct max8997_muic_reg_data *init_data;
81	int num_init_data;
82
83	/* Check cable state after certain delay */
84	int detcable_delay_ms;
85
86	/*
87	 * Default usb/uart path whether UART/USB or AUX_UART/AUX_USB
88	 * h/w path of COMP2/COMN1 on CONTROL1 register.
89	 */
90	int path_usb;
91	int path_uart;
92};
93
94enum max8997_haptic_motor_type {
95	MAX8997_HAPTIC_ERM,
96	MAX8997_HAPTIC_LRA,
97};
98
99enum max8997_haptic_pulse_mode {
100	MAX8997_EXTERNAL_MODE,
101	MAX8997_INTERNAL_MODE,
102};
103
104enum max8997_haptic_pwm_divisor {
105	MAX8997_PWM_DIVISOR_32,
106	MAX8997_PWM_DIVISOR_64,
107	MAX8997_PWM_DIVISOR_128,
108	MAX8997_PWM_DIVISOR_256,
109};
110
111/**
112 * max8997_haptic_platform_data
113 * @pwm_period: period in nano second for PWM device
114 *		valid for MAX8997_EXTERNAL_MODE
115 * @type: motor type
116 * @mode: pulse mode
117 *     MAX8997_EXTERNAL_MODE: external PWM device is used to control motor
118 *     MAX8997_INTERNAL_MODE: internal pulse generator is used to control motor
119 * @pwm_divisor: divisor for external PWM device
120 * @internal_mode_pattern: internal mode pattern for internal mode
121 *     [0 - 3]: valid pattern number
122 * @pattern_cycle: the number of cycles of the waveform
123 *		   for the internal mode pattern
124 *     [0 - 15]: available cycles
125 * @pattern_signal_period: period of the waveform for the internal mode pattern
126 *     [0 - 255]: available period
127 */
128struct max8997_haptic_platform_data {
129	unsigned int pwm_period;
130
131	enum max8997_haptic_motor_type type;
132	enum max8997_haptic_pulse_mode mode;
133	enum max8997_haptic_pwm_divisor pwm_divisor;
134
135	unsigned int internal_mode_pattern;
136	unsigned int pattern_cycle;
137	unsigned int pattern_signal_period;
138};
139
140enum max8997_led_mode {
141	MAX8997_NONE,
142	MAX8997_FLASH_MODE,
143	MAX8997_MOVIE_MODE,
144	MAX8997_FLASH_PIN_CONTROL_MODE,
145	MAX8997_MOVIE_PIN_CONTROL_MODE,
146};
147
148/**
149 *  struct max8997_led_platform_data
150 *  The number of LED devices for MAX8997 is two
151 *  @mode: LED mode for each LED device
152 *  @brightness: initial brightness for each LED device
153 *	range:
154 *	[0 - 31]: MAX8997_FLASH_MODE and MAX8997_FLASH_PIN_CONTROL_MODE
155 *	[0 - 15]: MAX8997_MOVIE_MODE and MAX8997_MOVIE_PIN_CONTROL_MODE
156 */
157struct max8997_led_platform_data {
158	enum max8997_led_mode mode[2];
159	u8 brightness[2];
160};
161
162struct max8997_platform_data {
163	/* IRQ */
164	int ono;
165
166	/* ---- PMIC ---- */
167	struct max8997_regulator_data *regulators;
168	int num_regulators;
169
170	/*
171	 * SET1~3 DVS GPIOs control Buck1, 2, and 5 simultaneously. Therefore,
172	 * With buckx_gpiodvs enabled, the buckx cannot be controlled
173	 * independently. To control buckx (of 1, 2, and 5) independently,
174	 * disable buckx_gpiodvs and control with BUCKxDVS1 register.
175	 *
176	 * When buckx_gpiodvs and bucky_gpiodvs are both enabled, set_voltage
177	 * on buckx will change the voltage of bucky at the same time.
178	 *
179	 */
180	bool ignore_gpiodvs_side_effect;
181	int buck125_default_idx; /* Default value of SET1, 2, 3 */
182	unsigned int buck1_voltage[8]; /* buckx_voltage in uV */
183	bool buck1_gpiodvs;
184	unsigned int buck2_voltage[8];
185	bool buck2_gpiodvs;
186	unsigned int buck5_voltage[8];
187	bool buck5_gpiodvs;
188
189	/* ---- Charger control ---- */
190	/* eoc stands for 'end of charge' */
191	int eoc_mA; /* 50 ~ 200mA by 10mA step */
192	/* charge Full Timeout */
193	int timeout; /* 0 (no timeout), 5, 6, 7 hours */
194
195	/* ---- MUIC ---- */
196	struct max8997_muic_platform_data *muic_pdata;
197
198	/* ---- HAPTIC ---- */
199	struct max8997_haptic_platform_data *haptic_pdata;
200
201	/* RTC: Not implemented */
202	/* ---- LED ---- */
203	struct max8997_led_platform_data *led_pdata;
204};
205
206#endif /* __LINUX_MFD_MAX8997_H */
207