1// SPDX-License-Identifier: GPL-1.0+ 2/* 3 * OHCI HCD (Host Controller Driver) for USB. 4 * 5 * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at> 6 * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net> 7 * (C) Copyright 2002 Hewlett-Packard Company 8 * 9 * Bus Glue for pxa27x 10 * 11 * Written by Christopher Hoover <ch@hpl.hp.com> 12 * Based on fragments of previous driver by Russell King et al. 13 * 14 * Modified for LH7A404 from ohci-sa1111.c 15 * by Durgesh Pattamatta <pattamattad@sharpsec.com> 16 * 17 * Modified for pxa27x from ohci-lh7a404.c 18 * by Nick Bane <nick@cecomputing.co.uk> 26-8-2004 19 * 20 * This file is licenced under the GPL. 21 */ 22 23#include <linux/clk.h> 24#include <linux/device.h> 25#include <linux/dma-mapping.h> 26#include <linux/io.h> 27#include <linux/kernel.h> 28#include <linux/module.h> 29#include <linux/of_platform.h> 30#include <linux/platform_data/usb-ohci-pxa27x.h> 31#include <linux/platform_data/pxa2xx_udc.h> 32#include <linux/platform_device.h> 33#include <linux/regulator/consumer.h> 34#include <linux/signal.h> 35#include <linux/usb.h> 36#include <linux/usb/hcd.h> 37#include <linux/usb/otg.h> 38#include <linux/soc/pxa/cpu.h> 39 40#include "ohci.h" 41 42#define DRIVER_DESC "OHCI PXA27x/PXA3x driver" 43 44/* 45 * UHC: USB Host Controller (OHCI-like) register definitions 46 */ 47#define UHCREV (0x0000) /* UHC HCI Spec Revision */ 48#define UHCHCON (0x0004) /* UHC Host Control Register */ 49#define UHCCOMS (0x0008) /* UHC Command Status Register */ 50#define UHCINTS (0x000C) /* UHC Interrupt Status Register */ 51#define UHCINTE (0x0010) /* UHC Interrupt Enable */ 52#define UHCINTD (0x0014) /* UHC Interrupt Disable */ 53#define UHCHCCA (0x0018) /* UHC Host Controller Comm. Area */ 54#define UHCPCED (0x001C) /* UHC Period Current Endpt Descr */ 55#define UHCCHED (0x0020) /* UHC Control Head Endpt Descr */ 56#define UHCCCED (0x0024) /* UHC Control Current Endpt Descr */ 57#define UHCBHED (0x0028) /* UHC Bulk Head Endpt Descr */ 58#define UHCBCED (0x002C) /* UHC Bulk Current Endpt Descr */ 59#define UHCDHEAD (0x0030) /* UHC Done Head */ 60#define UHCFMI (0x0034) /* UHC Frame Interval */ 61#define UHCFMR (0x0038) /* UHC Frame Remaining */ 62#define UHCFMN (0x003C) /* UHC Frame Number */ 63#define UHCPERS (0x0040) /* UHC Periodic Start */ 64#define UHCLS (0x0044) /* UHC Low Speed Threshold */ 65 66#define UHCRHDA (0x0048) /* UHC Root Hub Descriptor A */ 67#define UHCRHDA_NOCP (1 << 12) /* No over current protection */ 68#define UHCRHDA_OCPM (1 << 11) /* Over Current Protection Mode */ 69#define UHCRHDA_POTPGT(x) \ 70 (((x) & 0xff) << 24) /* Power On To Power Good Time */ 71 72#define UHCRHDB (0x004C) /* UHC Root Hub Descriptor B */ 73#define UHCRHS (0x0050) /* UHC Root Hub Status */ 74#define UHCRHPS1 (0x0054) /* UHC Root Hub Port 1 Status */ 75#define UHCRHPS2 (0x0058) /* UHC Root Hub Port 2 Status */ 76#define UHCRHPS3 (0x005C) /* UHC Root Hub Port 3 Status */ 77 78#define UHCSTAT (0x0060) /* UHC Status Register */ 79#define UHCSTAT_UPS3 (1 << 16) /* USB Power Sense Port3 */ 80#define UHCSTAT_SBMAI (1 << 15) /* System Bus Master Abort Interrupt*/ 81#define UHCSTAT_SBTAI (1 << 14) /* System Bus Target Abort Interrupt*/ 82#define UHCSTAT_UPRI (1 << 13) /* USB Port Resume Interrupt */ 83#define UHCSTAT_UPS2 (1 << 12) /* USB Power Sense Port 2 */ 84#define UHCSTAT_UPS1 (1 << 11) /* USB Power Sense Port 1 */ 85#define UHCSTAT_HTA (1 << 10) /* HCI Target Abort */ 86#define UHCSTAT_HBA (1 << 8) /* HCI Buffer Active */ 87#define UHCSTAT_RWUE (1 << 7) /* HCI Remote Wake Up Event */ 88 89#define UHCHR (0x0064) /* UHC Reset Register */ 90#define UHCHR_SSEP3 (1 << 11) /* Sleep Standby Enable for Port3 */ 91#define UHCHR_SSEP2 (1 << 10) /* Sleep Standby Enable for Port2 */ 92#define UHCHR_SSEP1 (1 << 9) /* Sleep Standby Enable for Port1 */ 93#define UHCHR_PCPL (1 << 7) /* Power control polarity low */ 94#define UHCHR_PSPL (1 << 6) /* Power sense polarity low */ 95#define UHCHR_SSE (1 << 5) /* Sleep Standby Enable */ 96#define UHCHR_UIT (1 << 4) /* USB Interrupt Test */ 97#define UHCHR_SSDC (1 << 3) /* Simulation Scale Down Clock */ 98#define UHCHR_CGR (1 << 2) /* Clock Generation Reset */ 99#define UHCHR_FHR (1 << 1) /* Force Host Controller Reset */ 100#define UHCHR_FSBIR (1 << 0) /* Force System Bus Iface Reset */ 101 102#define UHCHIE (0x0068) /* UHC Interrupt Enable Register*/ 103#define UHCHIE_UPS3IE (1 << 14) /* Power Sense Port3 IntEn */ 104#define UHCHIE_UPRIE (1 << 13) /* Port Resume IntEn */ 105#define UHCHIE_UPS2IE (1 << 12) /* Power Sense Port2 IntEn */ 106#define UHCHIE_UPS1IE (1 << 11) /* Power Sense Port1 IntEn */ 107#define UHCHIE_TAIE (1 << 10) /* HCI Interface Transfer Abort 108 Interrupt Enable*/ 109#define UHCHIE_HBAIE (1 << 8) /* HCI Buffer Active IntEn */ 110#define UHCHIE_RWIE (1 << 7) /* Remote Wake-up IntEn */ 111 112#define UHCHIT (0x006C) /* UHC Interrupt Test register */ 113 114#define PXA_UHC_MAX_PORTNUM 3 115 116static struct hc_driver __read_mostly ohci_pxa27x_hc_driver; 117 118struct pxa27x_ohci { 119 struct clk *clk; 120 void __iomem *mmio_base; 121 struct regulator *vbus[3]; 122 bool vbus_enabled[3]; 123}; 124 125#define to_pxa27x_ohci(hcd) (struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv) 126 127/* 128 PMM_NPS_MODE -- PMM Non-power switching mode 129 Ports are powered continuously. 130 131 PMM_GLOBAL_MODE -- PMM global switching mode 132 All ports are powered at the same time. 133 134 PMM_PERPORT_MODE -- PMM per port switching mode 135 Ports are powered individually. 136 */ 137static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *pxa_ohci, int mode) 138{ 139 uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA); 140 uint32_t uhcrhdb = __raw_readl(pxa_ohci->mmio_base + UHCRHDB); 141 142 switch (mode) { 143 case PMM_NPS_MODE: 144 uhcrhda |= RH_A_NPS; 145 break; 146 case PMM_GLOBAL_MODE: 147 uhcrhda &= ~(RH_A_NPS | RH_A_PSM); 148 break; 149 case PMM_PERPORT_MODE: 150 uhcrhda &= ~(RH_A_NPS); 151 uhcrhda |= RH_A_PSM; 152 153 /* Set port power control mask bits, only 3 ports. */ 154 uhcrhdb |= (0x7<<17); 155 break; 156 default: 157 printk( KERN_ERR 158 "Invalid mode %d, set to non-power switch mode.\n", 159 mode ); 160 161 uhcrhda |= RH_A_NPS; 162 } 163 164 __raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA); 165 __raw_writel(uhcrhdb, pxa_ohci->mmio_base + UHCRHDB); 166 return 0; 167} 168 169static int pxa27x_ohci_set_vbus_power(struct pxa27x_ohci *pxa_ohci, 170 unsigned int port, bool enable) 171{ 172 struct regulator *vbus = pxa_ohci->vbus[port]; 173 int ret = 0; 174 175 if (IS_ERR_OR_NULL(vbus)) 176 return 0; 177 178 if (enable && !pxa_ohci->vbus_enabled[port]) 179 ret = regulator_enable(vbus); 180 else if (!enable && pxa_ohci->vbus_enabled[port]) 181 ret = regulator_disable(vbus); 182 183 if (ret < 0) 184 return ret; 185 186 pxa_ohci->vbus_enabled[port] = enable; 187 188 return 0; 189} 190 191static int pxa27x_ohci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, 192 u16 wIndex, char *buf, u16 wLength) 193{ 194 struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd); 195 int ret; 196 197 switch (typeReq) { 198 case SetPortFeature: 199 case ClearPortFeature: 200 if (!wIndex || wIndex > 3) 201 return -EPIPE; 202 203 if (wValue != USB_PORT_FEAT_POWER) 204 break; 205 206 ret = pxa27x_ohci_set_vbus_power(pxa_ohci, wIndex - 1, 207 typeReq == SetPortFeature); 208 if (ret) 209 return ret; 210 break; 211 } 212 213 return ohci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength); 214} 215/*-------------------------------------------------------------------------*/ 216 217static inline void pxa27x_setup_hc(struct pxa27x_ohci *pxa_ohci, 218 struct pxaohci_platform_data *inf) 219{ 220 uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR); 221 uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA); 222 223 if (inf->flags & ENABLE_PORT1) 224 uhchr &= ~UHCHR_SSEP1; 225 226 if (inf->flags & ENABLE_PORT2) 227 uhchr &= ~UHCHR_SSEP2; 228 229 if (inf->flags & ENABLE_PORT3) 230 uhchr &= ~UHCHR_SSEP3; 231 232 if (inf->flags & POWER_CONTROL_LOW) 233 uhchr |= UHCHR_PCPL; 234 235 if (inf->flags & POWER_SENSE_LOW) 236 uhchr |= UHCHR_PSPL; 237 238 if (inf->flags & NO_OC_PROTECTION) 239 uhcrhda |= UHCRHDA_NOCP; 240 else 241 uhcrhda &= ~UHCRHDA_NOCP; 242 243 if (inf->flags & OC_MODE_PERPORT) 244 uhcrhda |= UHCRHDA_OCPM; 245 else 246 uhcrhda &= ~UHCRHDA_OCPM; 247 248 if (inf->power_on_delay) { 249 uhcrhda &= ~UHCRHDA_POTPGT(0xff); 250 uhcrhda |= UHCRHDA_POTPGT(inf->power_on_delay / 2); 251 } 252 253 __raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR); 254 __raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA); 255} 256 257static inline void pxa27x_reset_hc(struct pxa27x_ohci *pxa_ohci) 258{ 259 uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR); 260 261 __raw_writel(uhchr | UHCHR_FHR, pxa_ohci->mmio_base + UHCHR); 262 udelay(11); 263 __raw_writel(uhchr & ~UHCHR_FHR, pxa_ohci->mmio_base + UHCHR); 264} 265 266static int pxa27x_start_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev) 267{ 268 int retval; 269 struct pxaohci_platform_data *inf; 270 uint32_t uhchr; 271 272 inf = dev_get_platdata(dev); 273 274 retval = clk_prepare_enable(pxa_ohci->clk); 275 if (retval) 276 return retval; 277 278 pxa27x_reset_hc(pxa_ohci); 279 280 uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) | UHCHR_FSBIR; 281 __raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR); 282 283 while (__raw_readl(pxa_ohci->mmio_base + UHCHR) & UHCHR_FSBIR) 284 cpu_relax(); 285 286 pxa27x_setup_hc(pxa_ohci, inf); 287 288 if (inf->init) 289 retval = inf->init(dev); 290 291 if (retval < 0) { 292 clk_disable_unprepare(pxa_ohci->clk); 293 return retval; 294 } 295 296 uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) & ~UHCHR_SSE; 297 __raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR); 298 __raw_writel(UHCHIE_UPRIE | UHCHIE_RWIE, pxa_ohci->mmio_base + UHCHIE); 299 300 /* Clear any OTG Pin Hold */ 301 pxa27x_clear_otgph(); 302 return 0; 303} 304 305static void pxa27x_stop_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev) 306{ 307 struct pxaohci_platform_data *inf; 308 uint32_t uhccoms; 309 310 inf = dev_get_platdata(dev); 311 312 if (inf->exit) 313 inf->exit(dev); 314 315 pxa27x_reset_hc(pxa_ohci); 316 317 /* Host Controller Reset */ 318 uhccoms = __raw_readl(pxa_ohci->mmio_base + UHCCOMS) | 0x01; 319 __raw_writel(uhccoms, pxa_ohci->mmio_base + UHCCOMS); 320 udelay(10); 321 322 clk_disable_unprepare(pxa_ohci->clk); 323} 324 325#ifdef CONFIG_OF 326static const struct of_device_id pxa_ohci_dt_ids[] = { 327 { .compatible = "marvell,pxa-ohci" }, 328 { } 329}; 330 331MODULE_DEVICE_TABLE(of, pxa_ohci_dt_ids); 332 333static int ohci_pxa_of_init(struct platform_device *pdev) 334{ 335 struct device_node *np = pdev->dev.of_node; 336 struct pxaohci_platform_data *pdata; 337 u32 tmp; 338 int ret; 339 340 if (!np) 341 return 0; 342 343 /* Right now device-tree probed devices don't get dma_mask set. 344 * Since shared usb code relies on it, set it here for now. 345 * Once we have dma capability bindings this can go away. 346 */ 347 ret = dma_coerce_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); 348 if (ret) 349 return ret; 350 351 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); 352 if (!pdata) 353 return -ENOMEM; 354 355 if (of_property_read_bool(np, "marvell,enable-port1")) 356 pdata->flags |= ENABLE_PORT1; 357 if (of_property_read_bool(np, "marvell,enable-port2")) 358 pdata->flags |= ENABLE_PORT2; 359 if (of_property_read_bool(np, "marvell,enable-port3")) 360 pdata->flags |= ENABLE_PORT3; 361 if (of_property_read_bool(np, "marvell,port-sense-low")) 362 pdata->flags |= POWER_SENSE_LOW; 363 if (of_property_read_bool(np, "marvell,power-control-low")) 364 pdata->flags |= POWER_CONTROL_LOW; 365 if (of_property_read_bool(np, "marvell,no-oc-protection")) 366 pdata->flags |= NO_OC_PROTECTION; 367 if (of_property_read_bool(np, "marvell,oc-mode-perport")) 368 pdata->flags |= OC_MODE_PERPORT; 369 if (!of_property_read_u32(np, "marvell,power-on-delay", &tmp)) 370 pdata->power_on_delay = tmp; 371 if (!of_property_read_u32(np, "marvell,port-mode", &tmp)) 372 pdata->port_mode = tmp; 373 if (!of_property_read_u32(np, "marvell,power-budget", &tmp)) 374 pdata->power_budget = tmp; 375 376 pdev->dev.platform_data = pdata; 377 378 return 0; 379} 380#else 381static int ohci_pxa_of_init(struct platform_device *pdev) 382{ 383 return 0; 384} 385#endif 386 387/*-------------------------------------------------------------------------*/ 388 389/* configure so an HC device and id are always provided */ 390/* always called with process context; sleeping is OK */ 391 392 393/** 394 * ohci_hcd_pxa27x_probe - initialize pxa27x-based HCDs 395 * @pdev: USB Host controller to probe 396 * 397 * Context: task context, might sleep 398 * 399 * Allocates basic resources for this USB host controller, and 400 * then invokes the start() method for the HCD associated with it 401 * through the hotplug entry's driver_data. 402 */ 403static int ohci_hcd_pxa27x_probe(struct platform_device *pdev) 404{ 405 int retval, irq; 406 struct usb_hcd *hcd; 407 struct pxaohci_platform_data *inf; 408 struct pxa27x_ohci *pxa_ohci; 409 struct ohci_hcd *ohci; 410 struct resource *r; 411 struct clk *usb_clk; 412 unsigned int i; 413 414 retval = ohci_pxa_of_init(pdev); 415 if (retval) 416 return retval; 417 418 inf = dev_get_platdata(&pdev->dev); 419 420 if (!inf) 421 return -ENODEV; 422 423 irq = platform_get_irq(pdev, 0); 424 if (irq < 0) { 425 pr_err("no resource of IORESOURCE_IRQ"); 426 return irq; 427 } 428 429 usb_clk = devm_clk_get(&pdev->dev, NULL); 430 if (IS_ERR(usb_clk)) 431 return PTR_ERR(usb_clk); 432 433 hcd = usb_create_hcd(&ohci_pxa27x_hc_driver, &pdev->dev, "pxa27x"); 434 if (!hcd) 435 return -ENOMEM; 436 437 hcd->regs = devm_platform_get_and_ioremap_resource(pdev, 0, &r); 438 if (IS_ERR(hcd->regs)) { 439 retval = PTR_ERR(hcd->regs); 440 goto err; 441 } 442 hcd->rsrc_start = r->start; 443 hcd->rsrc_len = resource_size(r); 444 445 /* initialize "struct pxa27x_ohci" */ 446 pxa_ohci = to_pxa27x_ohci(hcd); 447 pxa_ohci->clk = usb_clk; 448 pxa_ohci->mmio_base = (void __iomem *)hcd->regs; 449 450 for (i = 0; i < 3; ++i) { 451 char name[6]; 452 453 if (!(inf->flags & (ENABLE_PORT1 << i))) 454 continue; 455 456 sprintf(name, "vbus%u", i + 1); 457 pxa_ohci->vbus[i] = devm_regulator_get(&pdev->dev, name); 458 } 459 460 retval = pxa27x_start_hc(pxa_ohci, &pdev->dev); 461 if (retval < 0) { 462 pr_debug("pxa27x_start_hc failed"); 463 goto err; 464 } 465 466 /* Select Power Management Mode */ 467 pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode); 468 469 if (inf->power_budget) 470 hcd->power_budget = inf->power_budget; 471 472 /* The value of NDP in roothub_a is incorrect on this hardware */ 473 ohci = hcd_to_ohci(hcd); 474 ohci->num_ports = 3; 475 476 retval = usb_add_hcd(hcd, irq, 0); 477 if (retval == 0) { 478 device_wakeup_enable(hcd->self.controller); 479 return retval; 480 } 481 482 pxa27x_stop_hc(pxa_ohci, &pdev->dev); 483 err: 484 usb_put_hcd(hcd); 485 return retval; 486} 487 488 489/* may be called without controller electrically present */ 490/* may be called with controller, bus, and devices active */ 491 492/** 493 * ohci_hcd_pxa27x_remove - shutdown processing for pxa27x-based HCDs 494 * @pdev: USB Host Controller being removed 495 * 496 * Context: task context, might sleep 497 * 498 * Reverses the effect of ohci_hcd_pxa27x_probe(), first invoking 499 * the HCD's stop() method. It is always called from a thread 500 * context, normally "rmmod", "apmd", or something similar. 501 */ 502static void ohci_hcd_pxa27x_remove(struct platform_device *pdev) 503{ 504 struct usb_hcd *hcd = platform_get_drvdata(pdev); 505 struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd); 506 unsigned int i; 507 508 usb_remove_hcd(hcd); 509 pxa27x_stop_hc(pxa_ohci, &pdev->dev); 510 511 for (i = 0; i < 3; ++i) 512 pxa27x_ohci_set_vbus_power(pxa_ohci, i, false); 513 514 usb_put_hcd(hcd); 515} 516 517/*-------------------------------------------------------------------------*/ 518 519#ifdef CONFIG_PM 520static int ohci_hcd_pxa27x_drv_suspend(struct device *dev) 521{ 522 struct usb_hcd *hcd = dev_get_drvdata(dev); 523 struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd); 524 struct ohci_hcd *ohci = hcd_to_ohci(hcd); 525 bool do_wakeup = device_may_wakeup(dev); 526 int ret; 527 528 529 if (time_before(jiffies, ohci->next_statechange)) 530 msleep(5); 531 ohci->next_statechange = jiffies; 532 533 ret = ohci_suspend(hcd, do_wakeup); 534 if (ret) 535 return ret; 536 537 pxa27x_stop_hc(pxa_ohci, dev); 538 return ret; 539} 540 541static int ohci_hcd_pxa27x_drv_resume(struct device *dev) 542{ 543 struct usb_hcd *hcd = dev_get_drvdata(dev); 544 struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd); 545 struct pxaohci_platform_data *inf = dev_get_platdata(dev); 546 struct ohci_hcd *ohci = hcd_to_ohci(hcd); 547 int status; 548 549 if (time_before(jiffies, ohci->next_statechange)) 550 msleep(5); 551 ohci->next_statechange = jiffies; 552 553 status = pxa27x_start_hc(pxa_ohci, dev); 554 if (status < 0) 555 return status; 556 557 /* Select Power Management Mode */ 558 pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode); 559 560 ohci_resume(hcd, false); 561 return 0; 562} 563 564static const struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = { 565 .suspend = ohci_hcd_pxa27x_drv_suspend, 566 .resume = ohci_hcd_pxa27x_drv_resume, 567}; 568#endif 569 570static struct platform_driver ohci_hcd_pxa27x_driver = { 571 .probe = ohci_hcd_pxa27x_probe, 572 .remove_new = ohci_hcd_pxa27x_remove, 573 .shutdown = usb_hcd_platform_shutdown, 574 .driver = { 575 .name = "pxa27x-ohci", 576 .of_match_table = of_match_ptr(pxa_ohci_dt_ids), 577#ifdef CONFIG_PM 578 .pm = &ohci_hcd_pxa27x_pm_ops, 579#endif 580 }, 581}; 582 583static const struct ohci_driver_overrides pxa27x_overrides __initconst = { 584 .extra_priv_size = sizeof(struct pxa27x_ohci), 585}; 586 587static int __init ohci_pxa27x_init(void) 588{ 589 if (usb_disabled()) 590 return -ENODEV; 591 592 ohci_init_driver(&ohci_pxa27x_hc_driver, &pxa27x_overrides); 593 ohci_pxa27x_hc_driver.hub_control = pxa27x_ohci_hub_control; 594 595 return platform_driver_register(&ohci_hcd_pxa27x_driver); 596} 597module_init(ohci_pxa27x_init); 598 599static void __exit ohci_pxa27x_cleanup(void) 600{ 601 platform_driver_unregister(&ohci_hcd_pxa27x_driver); 602} 603module_exit(ohci_pxa27x_cleanup); 604 605MODULE_DESCRIPTION(DRIVER_DESC); 606MODULE_LICENSE("GPL"); 607MODULE_ALIAS("platform:pxa27x-ohci"); 608