1// SPDX-License-Identifier: GPL-2.0+ 2 3/* 4 * NXP FlexSPI(FSPI) controller driver. 5 * 6 * Copyright 2019-2020 NXP 7 * Copyright 2020 Puresoftware Ltd. 8 * 9 * FlexSPI is a flexsible SPI host controller which supports two SPI 10 * channels and up to 4 external devices. Each channel supports 11 * Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional 12 * data lines). 13 * 14 * FlexSPI controller is driven by the LUT(Look-up Table) registers 15 * LUT registers are a look-up-table for sequences of instructions. 16 * A valid sequence consists of four LUT registers. 17 * Maximum 32 LUT sequences can be programmed simultaneously. 18 * 19 * LUTs are being created at run-time based on the commands passed 20 * from the spi-mem framework, thus using single LUT index. 21 * 22 * Software triggered Flash read/write access by IP Bus. 23 * 24 * Memory mapped read access by AHB Bus. 25 * 26 * Based on SPI MEM interface and spi-fsl-qspi.c driver. 27 * 28 * Author: 29 * Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com> 30 * Boris Brezillon <bbrezillon@kernel.org> 31 * Frieder Schrempf <frieder.schrempf@kontron.de> 32 */ 33 34#include <linux/acpi.h> 35#include <linux/bitops.h> 36#include <linux/bitfield.h> 37#include <linux/clk.h> 38#include <linux/completion.h> 39#include <linux/delay.h> 40#include <linux/err.h> 41#include <linux/errno.h> 42#include <linux/interrupt.h> 43#include <linux/io.h> 44#include <linux/iopoll.h> 45#include <linux/jiffies.h> 46#include <linux/kernel.h> 47#include <linux/module.h> 48#include <linux/mutex.h> 49#include <linux/of.h> 50#include <linux/platform_device.h> 51#include <linux/pm_qos.h> 52#include <linux/regmap.h> 53#include <linux/sizes.h> 54#include <linux/sys_soc.h> 55 56#include <linux/mfd/syscon.h> 57#include <linux/spi/spi.h> 58#include <linux/spi/spi-mem.h> 59 60/* 61 * The driver only uses one single LUT entry, that is updated on 62 * each call of exec_op(). Index 0 is preset at boot with a basic 63 * read operation, so let's use the last entry (31). 64 */ 65#define SEQID_LUT 31 66 67/* Registers used by the driver */ 68#define FSPI_MCR0 0x00 69#define FSPI_MCR0_AHB_TIMEOUT(x) ((x) << 24) 70#define FSPI_MCR0_IP_TIMEOUT(x) ((x) << 16) 71#define FSPI_MCR0_LEARN_EN BIT(15) 72#define FSPI_MCR0_SCRFRUN_EN BIT(14) 73#define FSPI_MCR0_OCTCOMB_EN BIT(13) 74#define FSPI_MCR0_DOZE_EN BIT(12) 75#define FSPI_MCR0_HSEN BIT(11) 76#define FSPI_MCR0_SERCLKDIV BIT(8) 77#define FSPI_MCR0_ATDF_EN BIT(7) 78#define FSPI_MCR0_ARDF_EN BIT(6) 79#define FSPI_MCR0_RXCLKSRC(x) ((x) << 4) 80#define FSPI_MCR0_END_CFG(x) ((x) << 2) 81#define FSPI_MCR0_MDIS BIT(1) 82#define FSPI_MCR0_SWRST BIT(0) 83 84#define FSPI_MCR1 0x04 85#define FSPI_MCR1_SEQ_TIMEOUT(x) ((x) << 16) 86#define FSPI_MCR1_AHB_TIMEOUT(x) (x) 87 88#define FSPI_MCR2 0x08 89#define FSPI_MCR2_IDLE_WAIT(x) ((x) << 24) 90#define FSPI_MCR2_SAMEDEVICEEN BIT(15) 91#define FSPI_MCR2_CLRLRPHS BIT(14) 92#define FSPI_MCR2_ABRDATSZ BIT(8) 93#define FSPI_MCR2_ABRLEARN BIT(7) 94#define FSPI_MCR2_ABR_READ BIT(6) 95#define FSPI_MCR2_ABRWRITE BIT(5) 96#define FSPI_MCR2_ABRDUMMY BIT(4) 97#define FSPI_MCR2_ABR_MODE BIT(3) 98#define FSPI_MCR2_ABRCADDR BIT(2) 99#define FSPI_MCR2_ABRRADDR BIT(1) 100#define FSPI_MCR2_ABR_CMD BIT(0) 101 102#define FSPI_AHBCR 0x0c 103#define FSPI_AHBCR_RDADDROPT BIT(6) 104#define FSPI_AHBCR_PREF_EN BIT(5) 105#define FSPI_AHBCR_BUFF_EN BIT(4) 106#define FSPI_AHBCR_CACH_EN BIT(3) 107#define FSPI_AHBCR_CLRTXBUF BIT(2) 108#define FSPI_AHBCR_CLRRXBUF BIT(1) 109#define FSPI_AHBCR_PAR_EN BIT(0) 110 111#define FSPI_INTEN 0x10 112#define FSPI_INTEN_SCLKSBWR BIT(9) 113#define FSPI_INTEN_SCLKSBRD BIT(8) 114#define FSPI_INTEN_DATALRNFL BIT(7) 115#define FSPI_INTEN_IPTXWE BIT(6) 116#define FSPI_INTEN_IPRXWA BIT(5) 117#define FSPI_INTEN_AHBCMDERR BIT(4) 118#define FSPI_INTEN_IPCMDERR BIT(3) 119#define FSPI_INTEN_AHBCMDGE BIT(2) 120#define FSPI_INTEN_IPCMDGE BIT(1) 121#define FSPI_INTEN_IPCMDDONE BIT(0) 122 123#define FSPI_INTR 0x14 124#define FSPI_INTR_SCLKSBWR BIT(9) 125#define FSPI_INTR_SCLKSBRD BIT(8) 126#define FSPI_INTR_DATALRNFL BIT(7) 127#define FSPI_INTR_IPTXWE BIT(6) 128#define FSPI_INTR_IPRXWA BIT(5) 129#define FSPI_INTR_AHBCMDERR BIT(4) 130#define FSPI_INTR_IPCMDERR BIT(3) 131#define FSPI_INTR_AHBCMDGE BIT(2) 132#define FSPI_INTR_IPCMDGE BIT(1) 133#define FSPI_INTR_IPCMDDONE BIT(0) 134 135#define FSPI_LUTKEY 0x18 136#define FSPI_LUTKEY_VALUE 0x5AF05AF0 137 138#define FSPI_LCKCR 0x1C 139 140#define FSPI_LCKER_LOCK 0x1 141#define FSPI_LCKER_UNLOCK 0x2 142 143#define FSPI_BUFXCR_INVALID_MSTRID 0xE 144#define FSPI_AHBRX_BUF0CR0 0x20 145#define FSPI_AHBRX_BUF1CR0 0x24 146#define FSPI_AHBRX_BUF2CR0 0x28 147#define FSPI_AHBRX_BUF3CR0 0x2C 148#define FSPI_AHBRX_BUF4CR0 0x30 149#define FSPI_AHBRX_BUF5CR0 0x34 150#define FSPI_AHBRX_BUF6CR0 0x38 151#define FSPI_AHBRX_BUF7CR0 0x3C 152#define FSPI_AHBRXBUF0CR7_PREF BIT(31) 153 154#define FSPI_AHBRX_BUF0CR1 0x40 155#define FSPI_AHBRX_BUF1CR1 0x44 156#define FSPI_AHBRX_BUF2CR1 0x48 157#define FSPI_AHBRX_BUF3CR1 0x4C 158#define FSPI_AHBRX_BUF4CR1 0x50 159#define FSPI_AHBRX_BUF5CR1 0x54 160#define FSPI_AHBRX_BUF6CR1 0x58 161#define FSPI_AHBRX_BUF7CR1 0x5C 162 163#define FSPI_FLSHA1CR0 0x60 164#define FSPI_FLSHA2CR0 0x64 165#define FSPI_FLSHB1CR0 0x68 166#define FSPI_FLSHB2CR0 0x6C 167#define FSPI_FLSHXCR0_SZ_KB 10 168#define FSPI_FLSHXCR0_SZ(x) ((x) >> FSPI_FLSHXCR0_SZ_KB) 169 170#define FSPI_FLSHA1CR1 0x70 171#define FSPI_FLSHA2CR1 0x74 172#define FSPI_FLSHB1CR1 0x78 173#define FSPI_FLSHB2CR1 0x7C 174#define FSPI_FLSHXCR1_CSINTR(x) ((x) << 16) 175#define FSPI_FLSHXCR1_CAS(x) ((x) << 11) 176#define FSPI_FLSHXCR1_WA BIT(10) 177#define FSPI_FLSHXCR1_TCSH(x) ((x) << 5) 178#define FSPI_FLSHXCR1_TCSS(x) (x) 179 180#define FSPI_FLSHA1CR2 0x80 181#define FSPI_FLSHA2CR2 0x84 182#define FSPI_FLSHB1CR2 0x88 183#define FSPI_FLSHB2CR2 0x8C 184#define FSPI_FLSHXCR2_CLRINSP BIT(24) 185#define FSPI_FLSHXCR2_AWRWAIT BIT(16) 186#define FSPI_FLSHXCR2_AWRSEQN_SHIFT 13 187#define FSPI_FLSHXCR2_AWRSEQI_SHIFT 8 188#define FSPI_FLSHXCR2_ARDSEQN_SHIFT 5 189#define FSPI_FLSHXCR2_ARDSEQI_SHIFT 0 190 191#define FSPI_IPCR0 0xA0 192 193#define FSPI_IPCR1 0xA4 194#define FSPI_IPCR1_IPAREN BIT(31) 195#define FSPI_IPCR1_SEQNUM_SHIFT 24 196#define FSPI_IPCR1_SEQID_SHIFT 16 197#define FSPI_IPCR1_IDATSZ(x) (x) 198 199#define FSPI_IPCMD 0xB0 200#define FSPI_IPCMD_TRG BIT(0) 201 202#define FSPI_DLPR 0xB4 203 204#define FSPI_IPRXFCR 0xB8 205#define FSPI_IPRXFCR_CLR BIT(0) 206#define FSPI_IPRXFCR_DMA_EN BIT(1) 207#define FSPI_IPRXFCR_WMRK(x) ((x) << 2) 208 209#define FSPI_IPTXFCR 0xBC 210#define FSPI_IPTXFCR_CLR BIT(0) 211#define FSPI_IPTXFCR_DMA_EN BIT(1) 212#define FSPI_IPTXFCR_WMRK(x) ((x) << 2) 213 214#define FSPI_DLLACR 0xC0 215#define FSPI_DLLACR_OVRDEN BIT(8) 216#define FSPI_DLLACR_SLVDLY(x) ((x) << 3) 217#define FSPI_DLLACR_DLLRESET BIT(1) 218#define FSPI_DLLACR_DLLEN BIT(0) 219 220#define FSPI_DLLBCR 0xC4 221#define FSPI_DLLBCR_OVRDEN BIT(8) 222#define FSPI_DLLBCR_SLVDLY(x) ((x) << 3) 223#define FSPI_DLLBCR_DLLRESET BIT(1) 224#define FSPI_DLLBCR_DLLEN BIT(0) 225 226#define FSPI_STS0 0xE0 227#define FSPI_STS0_DLPHB(x) ((x) << 8) 228#define FSPI_STS0_DLPHA(x) ((x) << 4) 229#define FSPI_STS0_CMD_SRC(x) ((x) << 2) 230#define FSPI_STS0_ARB_IDLE BIT(1) 231#define FSPI_STS0_SEQ_IDLE BIT(0) 232 233#define FSPI_STS1 0xE4 234#define FSPI_STS1_IP_ERRCD(x) ((x) << 24) 235#define FSPI_STS1_IP_ERRID(x) ((x) << 16) 236#define FSPI_STS1_AHB_ERRCD(x) ((x) << 8) 237#define FSPI_STS1_AHB_ERRID(x) (x) 238 239#define FSPI_STS2 0xE8 240#define FSPI_STS2_BREFLOCK BIT(17) 241#define FSPI_STS2_BSLVLOCK BIT(16) 242#define FSPI_STS2_AREFLOCK BIT(1) 243#define FSPI_STS2_ASLVLOCK BIT(0) 244#define FSPI_STS2_AB_LOCK (FSPI_STS2_BREFLOCK | \ 245 FSPI_STS2_BSLVLOCK | \ 246 FSPI_STS2_AREFLOCK | \ 247 FSPI_STS2_ASLVLOCK) 248 249#define FSPI_AHBSPNST 0xEC 250#define FSPI_AHBSPNST_DATLFT(x) ((x) << 16) 251#define FSPI_AHBSPNST_BUFID(x) ((x) << 1) 252#define FSPI_AHBSPNST_ACTIVE BIT(0) 253 254#define FSPI_IPRXFSTS 0xF0 255#define FSPI_IPRXFSTS_RDCNTR(x) ((x) << 16) 256#define FSPI_IPRXFSTS_FILL(x) (x) 257 258#define FSPI_IPTXFSTS 0xF4 259#define FSPI_IPTXFSTS_WRCNTR(x) ((x) << 16) 260#define FSPI_IPTXFSTS_FILL(x) (x) 261 262#define FSPI_RFDR 0x100 263#define FSPI_TFDR 0x180 264 265#define FSPI_LUT_BASE 0x200 266#define FSPI_LUT_OFFSET (SEQID_LUT * 4 * 4) 267#define FSPI_LUT_REG(idx) \ 268 (FSPI_LUT_BASE + FSPI_LUT_OFFSET + (idx) * 4) 269 270/* register map end */ 271 272/* Instruction set for the LUT register. */ 273#define LUT_STOP 0x00 274#define LUT_CMD 0x01 275#define LUT_ADDR 0x02 276#define LUT_CADDR_SDR 0x03 277#define LUT_MODE 0x04 278#define LUT_MODE2 0x05 279#define LUT_MODE4 0x06 280#define LUT_MODE8 0x07 281#define LUT_NXP_WRITE 0x08 282#define LUT_NXP_READ 0x09 283#define LUT_LEARN_SDR 0x0A 284#define LUT_DATSZ_SDR 0x0B 285#define LUT_DUMMY 0x0C 286#define LUT_DUMMY_RWDS_SDR 0x0D 287#define LUT_JMP_ON_CS 0x1F 288#define LUT_CMD_DDR 0x21 289#define LUT_ADDR_DDR 0x22 290#define LUT_CADDR_DDR 0x23 291#define LUT_MODE_DDR 0x24 292#define LUT_MODE2_DDR 0x25 293#define LUT_MODE4_DDR 0x26 294#define LUT_MODE8_DDR 0x27 295#define LUT_WRITE_DDR 0x28 296#define LUT_READ_DDR 0x29 297#define LUT_LEARN_DDR 0x2A 298#define LUT_DATSZ_DDR 0x2B 299#define LUT_DUMMY_DDR 0x2C 300#define LUT_DUMMY_RWDS_DDR 0x2D 301 302/* 303 * Calculate number of required PAD bits for LUT register. 304 * 305 * The pad stands for the number of IO lines [0:7]. 306 * For example, the octal read needs eight IO lines, 307 * so you should use LUT_PAD(8). This macro 308 * returns 3 i.e. use eight (2^3) IP lines for read. 309 */ 310#define LUT_PAD(x) (fls(x) - 1) 311 312/* 313 * Macro for constructing the LUT entries with the following 314 * register layout: 315 * 316 * --------------------------------------------------- 317 * | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 | 318 * --------------------------------------------------- 319 */ 320#define PAD_SHIFT 8 321#define INSTR_SHIFT 10 322#define OPRND_SHIFT 16 323 324/* Macros for constructing the LUT register. */ 325#define LUT_DEF(idx, ins, pad, opr) \ 326 ((((ins) << INSTR_SHIFT) | ((pad) << PAD_SHIFT) | \ 327 (opr)) << (((idx) % 2) * OPRND_SHIFT)) 328 329#define POLL_TOUT 5000 330#define NXP_FSPI_MAX_CHIPSELECT 4 331#define NXP_FSPI_MIN_IOMAP SZ_4M 332 333#define DCFG_RCWSR1 0x100 334#define SYS_PLL_RAT GENMASK(6, 2) 335 336/* Access flash memory using IP bus only */ 337#define FSPI_QUIRK_USE_IP_ONLY BIT(0) 338 339struct nxp_fspi_devtype_data { 340 unsigned int rxfifo; 341 unsigned int txfifo; 342 unsigned int ahb_buf_size; 343 unsigned int quirks; 344 bool little_endian; 345}; 346 347static struct nxp_fspi_devtype_data lx2160a_data = { 348 .rxfifo = SZ_512, /* (64 * 64 bits) */ 349 .txfifo = SZ_1K, /* (128 * 64 bits) */ 350 .ahb_buf_size = SZ_2K, /* (256 * 64 bits) */ 351 .quirks = 0, 352 .little_endian = true, /* little-endian */ 353}; 354 355static struct nxp_fspi_devtype_data imx8mm_data = { 356 .rxfifo = SZ_512, /* (64 * 64 bits) */ 357 .txfifo = SZ_1K, /* (128 * 64 bits) */ 358 .ahb_buf_size = SZ_2K, /* (256 * 64 bits) */ 359 .quirks = 0, 360 .little_endian = true, /* little-endian */ 361}; 362 363static struct nxp_fspi_devtype_data imx8qxp_data = { 364 .rxfifo = SZ_512, /* (64 * 64 bits) */ 365 .txfifo = SZ_1K, /* (128 * 64 bits) */ 366 .ahb_buf_size = SZ_2K, /* (256 * 64 bits) */ 367 .quirks = 0, 368 .little_endian = true, /* little-endian */ 369}; 370 371static struct nxp_fspi_devtype_data imx8dxl_data = { 372 .rxfifo = SZ_512, /* (64 * 64 bits) */ 373 .txfifo = SZ_1K, /* (128 * 64 bits) */ 374 .ahb_buf_size = SZ_2K, /* (256 * 64 bits) */ 375 .quirks = FSPI_QUIRK_USE_IP_ONLY, 376 .little_endian = true, /* little-endian */ 377}; 378 379struct nxp_fspi { 380 void __iomem *iobase; 381 void __iomem *ahb_addr; 382 u32 memmap_phy; 383 u32 memmap_phy_size; 384 u32 memmap_start; 385 u32 memmap_len; 386 struct clk *clk, *clk_en; 387 struct device *dev; 388 struct completion c; 389 struct nxp_fspi_devtype_data *devtype_data; 390 struct mutex lock; 391 struct pm_qos_request pm_qos_req; 392 int selected; 393}; 394 395static inline int needs_ip_only(struct nxp_fspi *f) 396{ 397 return f->devtype_data->quirks & FSPI_QUIRK_USE_IP_ONLY; 398} 399 400/* 401 * R/W functions for big- or little-endian registers: 402 * The FSPI controller's endianness is independent of 403 * the CPU core's endianness. So far, although the CPU 404 * core is little-endian the FSPI controller can use 405 * big-endian or little-endian. 406 */ 407static void fspi_writel(struct nxp_fspi *f, u32 val, void __iomem *addr) 408{ 409 if (f->devtype_data->little_endian) 410 iowrite32(val, addr); 411 else 412 iowrite32be(val, addr); 413} 414 415static u32 fspi_readl(struct nxp_fspi *f, void __iomem *addr) 416{ 417 if (f->devtype_data->little_endian) 418 return ioread32(addr); 419 else 420 return ioread32be(addr); 421} 422 423static irqreturn_t nxp_fspi_irq_handler(int irq, void *dev_id) 424{ 425 struct nxp_fspi *f = dev_id; 426 u32 reg; 427 428 /* clear interrupt */ 429 reg = fspi_readl(f, f->iobase + FSPI_INTR); 430 fspi_writel(f, FSPI_INTR_IPCMDDONE, f->iobase + FSPI_INTR); 431 432 if (reg & FSPI_INTR_IPCMDDONE) 433 complete(&f->c); 434 435 return IRQ_HANDLED; 436} 437 438static int nxp_fspi_check_buswidth(struct nxp_fspi *f, u8 width) 439{ 440 switch (width) { 441 case 1: 442 case 2: 443 case 4: 444 case 8: 445 return 0; 446 } 447 448 return -ENOTSUPP; 449} 450 451static bool nxp_fspi_supports_op(struct spi_mem *mem, 452 const struct spi_mem_op *op) 453{ 454 struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->controller); 455 int ret; 456 457 ret = nxp_fspi_check_buswidth(f, op->cmd.buswidth); 458 459 if (op->addr.nbytes) 460 ret |= nxp_fspi_check_buswidth(f, op->addr.buswidth); 461 462 if (op->dummy.nbytes) 463 ret |= nxp_fspi_check_buswidth(f, op->dummy.buswidth); 464 465 if (op->data.nbytes) 466 ret |= nxp_fspi_check_buswidth(f, op->data.buswidth); 467 468 if (ret) 469 return false; 470 471 /* 472 * The number of address bytes should be equal to or less than 4 bytes. 473 */ 474 if (op->addr.nbytes > 4) 475 return false; 476 477 /* 478 * If requested address value is greater than controller assigned 479 * memory mapped space, return error as it didn't fit in the range 480 * of assigned address space. 481 */ 482 if (op->addr.val >= f->memmap_phy_size) 483 return false; 484 485 /* Max 64 dummy clock cycles supported */ 486 if (op->dummy.buswidth && 487 (op->dummy.nbytes * 8 / op->dummy.buswidth > 64)) 488 return false; 489 490 /* Max data length, check controller limits and alignment */ 491 if (op->data.dir == SPI_MEM_DATA_IN && 492 (op->data.nbytes > f->devtype_data->ahb_buf_size || 493 (op->data.nbytes > f->devtype_data->rxfifo - 4 && 494 !IS_ALIGNED(op->data.nbytes, 8)))) 495 return false; 496 497 if (op->data.dir == SPI_MEM_DATA_OUT && 498 op->data.nbytes > f->devtype_data->txfifo) 499 return false; 500 501 return spi_mem_default_supports_op(mem, op); 502} 503 504/* Instead of busy looping invoke readl_poll_timeout functionality. */ 505static int fspi_readl_poll_tout(struct nxp_fspi *f, void __iomem *base, 506 u32 mask, u32 delay_us, 507 u32 timeout_us, bool c) 508{ 509 u32 reg; 510 511 if (!f->devtype_data->little_endian) 512 mask = (u32)cpu_to_be32(mask); 513 514 if (c) 515 return readl_poll_timeout(base, reg, (reg & mask), 516 delay_us, timeout_us); 517 else 518 return readl_poll_timeout(base, reg, !(reg & mask), 519 delay_us, timeout_us); 520} 521 522/* 523 * If the target device content being changed by Write/Erase, need to 524 * invalidate the AHB buffer. This can be achieved by doing the reset 525 * of controller after setting MCR0[SWRESET] bit. 526 */ 527static inline void nxp_fspi_invalid(struct nxp_fspi *f) 528{ 529 u32 reg; 530 int ret; 531 532 reg = fspi_readl(f, f->iobase + FSPI_MCR0); 533 fspi_writel(f, reg | FSPI_MCR0_SWRST, f->iobase + FSPI_MCR0); 534 535 /* w1c register, wait unit clear */ 536 ret = fspi_readl_poll_tout(f, f->iobase + FSPI_MCR0, 537 FSPI_MCR0_SWRST, 0, POLL_TOUT, false); 538 WARN_ON(ret); 539} 540 541static void nxp_fspi_prepare_lut(struct nxp_fspi *f, 542 const struct spi_mem_op *op) 543{ 544 void __iomem *base = f->iobase; 545 u32 lutval[4] = {}; 546 int lutidx = 1, i; 547 548 /* cmd */ 549 lutval[0] |= LUT_DEF(0, LUT_CMD, LUT_PAD(op->cmd.buswidth), 550 op->cmd.opcode); 551 552 /* addr bytes */ 553 if (op->addr.nbytes) { 554 lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_ADDR, 555 LUT_PAD(op->addr.buswidth), 556 op->addr.nbytes * 8); 557 lutidx++; 558 } 559 560 /* dummy bytes, if needed */ 561 if (op->dummy.nbytes) { 562 lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_DUMMY, 563 /* 564 * Due to FlexSPI controller limitation number of PAD for dummy 565 * buswidth needs to be programmed as equal to data buswidth. 566 */ 567 LUT_PAD(op->data.buswidth), 568 op->dummy.nbytes * 8 / 569 op->dummy.buswidth); 570 lutidx++; 571 } 572 573 /* read/write data bytes */ 574 if (op->data.nbytes) { 575 lutval[lutidx / 2] |= LUT_DEF(lutidx, 576 op->data.dir == SPI_MEM_DATA_IN ? 577 LUT_NXP_READ : LUT_NXP_WRITE, 578 LUT_PAD(op->data.buswidth), 579 0); 580 lutidx++; 581 } 582 583 /* stop condition. */ 584 lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_STOP, 0, 0); 585 586 /* unlock LUT */ 587 fspi_writel(f, FSPI_LUTKEY_VALUE, f->iobase + FSPI_LUTKEY); 588 fspi_writel(f, FSPI_LCKER_UNLOCK, f->iobase + FSPI_LCKCR); 589 590 /* fill LUT */ 591 for (i = 0; i < ARRAY_SIZE(lutval); i++) 592 fspi_writel(f, lutval[i], base + FSPI_LUT_REG(i)); 593 594 dev_dbg(f->dev, "CMD[%02x] lutval[0:%08x 1:%08x 2:%08x 3:%08x], size: 0x%08x\n", 595 op->cmd.opcode, lutval[0], lutval[1], lutval[2], lutval[3], op->data.nbytes); 596 597 /* lock LUT */ 598 fspi_writel(f, FSPI_LUTKEY_VALUE, f->iobase + FSPI_LUTKEY); 599 fspi_writel(f, FSPI_LCKER_LOCK, f->iobase + FSPI_LCKCR); 600} 601 602static int nxp_fspi_clk_prep_enable(struct nxp_fspi *f) 603{ 604 int ret; 605 606 if (is_acpi_node(dev_fwnode(f->dev))) 607 return 0; 608 609 ret = clk_prepare_enable(f->clk_en); 610 if (ret) 611 return ret; 612 613 ret = clk_prepare_enable(f->clk); 614 if (ret) { 615 clk_disable_unprepare(f->clk_en); 616 return ret; 617 } 618 619 return 0; 620} 621 622static int nxp_fspi_clk_disable_unprep(struct nxp_fspi *f) 623{ 624 if (is_acpi_node(dev_fwnode(f->dev))) 625 return 0; 626 627 clk_disable_unprepare(f->clk); 628 clk_disable_unprepare(f->clk_en); 629 630 return 0; 631} 632 633static void nxp_fspi_dll_calibration(struct nxp_fspi *f) 634{ 635 int ret; 636 637 /* Reset the DLL, set the DLLRESET to 1 and then set to 0 */ 638 fspi_writel(f, FSPI_DLLACR_DLLRESET, f->iobase + FSPI_DLLACR); 639 fspi_writel(f, FSPI_DLLBCR_DLLRESET, f->iobase + FSPI_DLLBCR); 640 fspi_writel(f, 0, f->iobase + FSPI_DLLACR); 641 fspi_writel(f, 0, f->iobase + FSPI_DLLBCR); 642 643 /* 644 * Enable the DLL calibration mode. 645 * The delay target for slave delay line is: 646 * ((SLVDLYTARGET+1) * 1/32 * clock cycle of reference clock. 647 * When clock rate > 100MHz, recommend SLVDLYTARGET is 0xF, which 648 * means half of clock cycle of reference clock. 649 */ 650 fspi_writel(f, FSPI_DLLACR_DLLEN | FSPI_DLLACR_SLVDLY(0xF), 651 f->iobase + FSPI_DLLACR); 652 fspi_writel(f, FSPI_DLLBCR_DLLEN | FSPI_DLLBCR_SLVDLY(0xF), 653 f->iobase + FSPI_DLLBCR); 654 655 /* Wait to get REF/SLV lock */ 656 ret = fspi_readl_poll_tout(f, f->iobase + FSPI_STS2, FSPI_STS2_AB_LOCK, 657 0, POLL_TOUT, true); 658 if (ret) 659 dev_warn(f->dev, "DLL lock failed, please fix it!\n"); 660} 661 662/* 663 * In FlexSPI controller, flash access is based on value of FSPI_FLSHXXCR0 664 * register and start base address of the target device. 665 * 666 * (Higher address) 667 * -------- <-- FLSHB2CR0 668 * | B2 | 669 * | | 670 * B2 start address --> -------- <-- FLSHB1CR0 671 * | B1 | 672 * | | 673 * B1 start address --> -------- <-- FLSHA2CR0 674 * | A2 | 675 * | | 676 * A2 start address --> -------- <-- FLSHA1CR0 677 * | A1 | 678 * | | 679 * A1 start address --> -------- (Lower address) 680 * 681 * 682 * Start base address defines the starting address range for given CS and 683 * FSPI_FLSHXXCR0 defines the size of the target device connected at given CS. 684 * 685 * But, different targets are having different combinations of number of CS, 686 * some targets only have single CS or two CS covering controller's full 687 * memory mapped space area. 688 * Thus, implementation is being done as independent of the size and number 689 * of the connected target device. 690 * Assign controller memory mapped space size as the size to the connected 691 * target device. 692 * Mark FLSHxxCR0 as zero initially and then assign value only to the selected 693 * chip-select Flash configuration register. 694 * 695 * For e.g. to access CS2 (B1), FLSHB1CR0 register would be equal to the 696 * memory mapped size of the controller. 697 * Value for rest of the CS FLSHxxCR0 register would be zero. 698 * 699 */ 700static void nxp_fspi_select_mem(struct nxp_fspi *f, struct spi_device *spi) 701{ 702 unsigned long rate = spi->max_speed_hz; 703 int ret; 704 uint64_t size_kb; 705 706 /* 707 * Return, if previously selected target device is same as current 708 * requested target device. 709 */ 710 if (f->selected == spi_get_chipselect(spi, 0)) 711 return; 712 713 /* Reset FLSHxxCR0 registers */ 714 fspi_writel(f, 0, f->iobase + FSPI_FLSHA1CR0); 715 fspi_writel(f, 0, f->iobase + FSPI_FLSHA2CR0); 716 fspi_writel(f, 0, f->iobase + FSPI_FLSHB1CR0); 717 fspi_writel(f, 0, f->iobase + FSPI_FLSHB2CR0); 718 719 /* Assign controller memory mapped space as size, KBytes, of flash. */ 720 size_kb = FSPI_FLSHXCR0_SZ(f->memmap_phy_size); 721 722 fspi_writel(f, size_kb, f->iobase + FSPI_FLSHA1CR0 + 723 4 * spi_get_chipselect(spi, 0)); 724 725 dev_dbg(f->dev, "Target device [CS:%x] selected\n", spi_get_chipselect(spi, 0)); 726 727 nxp_fspi_clk_disable_unprep(f); 728 729 ret = clk_set_rate(f->clk, rate); 730 if (ret) 731 return; 732 733 ret = nxp_fspi_clk_prep_enable(f); 734 if (ret) 735 return; 736 737 /* 738 * If clock rate > 100MHz, then switch from DLL override mode to 739 * DLL calibration mode. 740 */ 741 if (rate > 100000000) 742 nxp_fspi_dll_calibration(f); 743 744 f->selected = spi_get_chipselect(spi, 0); 745} 746 747static int nxp_fspi_read_ahb(struct nxp_fspi *f, const struct spi_mem_op *op) 748{ 749 u32 start = op->addr.val; 750 u32 len = op->data.nbytes; 751 752 /* if necessary, ioremap before AHB read */ 753 if ((!f->ahb_addr) || start < f->memmap_start || 754 start + len > f->memmap_start + f->memmap_len) { 755 if (f->ahb_addr) 756 iounmap(f->ahb_addr); 757 758 f->memmap_start = start; 759 f->memmap_len = len > NXP_FSPI_MIN_IOMAP ? 760 len : NXP_FSPI_MIN_IOMAP; 761 762 f->ahb_addr = ioremap(f->memmap_phy + f->memmap_start, 763 f->memmap_len); 764 765 if (!f->ahb_addr) { 766 dev_err(f->dev, "failed to alloc memory\n"); 767 return -ENOMEM; 768 } 769 } 770 771 /* Read out the data directly from the AHB buffer. */ 772 memcpy_fromio(op->data.buf.in, 773 f->ahb_addr + start - f->memmap_start, len); 774 775 return 0; 776} 777 778static void nxp_fspi_fill_txfifo(struct nxp_fspi *f, 779 const struct spi_mem_op *op) 780{ 781 void __iomem *base = f->iobase; 782 int i, ret; 783 u8 *buf = (u8 *) op->data.buf.out; 784 785 /* clear the TX FIFO. */ 786 fspi_writel(f, FSPI_IPTXFCR_CLR, base + FSPI_IPTXFCR); 787 788 /* 789 * Default value of water mark level is 8 bytes, hence in single 790 * write request controller can write max 8 bytes of data. 791 */ 792 793 for (i = 0; i < ALIGN_DOWN(op->data.nbytes, 8); i += 8) { 794 /* Wait for TXFIFO empty */ 795 ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR, 796 FSPI_INTR_IPTXWE, 0, 797 POLL_TOUT, true); 798 WARN_ON(ret); 799 800 fspi_writel(f, *(u32 *) (buf + i), base + FSPI_TFDR); 801 fspi_writel(f, *(u32 *) (buf + i + 4), base + FSPI_TFDR + 4); 802 fspi_writel(f, FSPI_INTR_IPTXWE, base + FSPI_INTR); 803 } 804 805 if (i < op->data.nbytes) { 806 u32 data = 0; 807 int j; 808 /* Wait for TXFIFO empty */ 809 ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR, 810 FSPI_INTR_IPTXWE, 0, 811 POLL_TOUT, true); 812 WARN_ON(ret); 813 814 for (j = 0; j < ALIGN(op->data.nbytes - i, 4); j += 4) { 815 memcpy(&data, buf + i + j, 4); 816 fspi_writel(f, data, base + FSPI_TFDR + j); 817 } 818 fspi_writel(f, FSPI_INTR_IPTXWE, base + FSPI_INTR); 819 } 820} 821 822static void nxp_fspi_read_rxfifo(struct nxp_fspi *f, 823 const struct spi_mem_op *op) 824{ 825 void __iomem *base = f->iobase; 826 int i, ret; 827 int len = op->data.nbytes; 828 u8 *buf = (u8 *) op->data.buf.in; 829 830 /* 831 * Default value of water mark level is 8 bytes, hence in single 832 * read request controller can read max 8 bytes of data. 833 */ 834 for (i = 0; i < ALIGN_DOWN(len, 8); i += 8) { 835 /* Wait for RXFIFO available */ 836 ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR, 837 FSPI_INTR_IPRXWA, 0, 838 POLL_TOUT, true); 839 WARN_ON(ret); 840 841 *(u32 *)(buf + i) = fspi_readl(f, base + FSPI_RFDR); 842 *(u32 *)(buf + i + 4) = fspi_readl(f, base + FSPI_RFDR + 4); 843 /* move the FIFO pointer */ 844 fspi_writel(f, FSPI_INTR_IPRXWA, base + FSPI_INTR); 845 } 846 847 if (i < len) { 848 u32 tmp; 849 int size, j; 850 851 buf = op->data.buf.in + i; 852 /* Wait for RXFIFO available */ 853 ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR, 854 FSPI_INTR_IPRXWA, 0, 855 POLL_TOUT, true); 856 WARN_ON(ret); 857 858 len = op->data.nbytes - i; 859 for (j = 0; j < op->data.nbytes - i; j += 4) { 860 tmp = fspi_readl(f, base + FSPI_RFDR + j); 861 size = min(len, 4); 862 memcpy(buf + j, &tmp, size); 863 len -= size; 864 } 865 } 866 867 /* invalid the RXFIFO */ 868 fspi_writel(f, FSPI_IPRXFCR_CLR, base + FSPI_IPRXFCR); 869 /* move the FIFO pointer */ 870 fspi_writel(f, FSPI_INTR_IPRXWA, base + FSPI_INTR); 871} 872 873static int nxp_fspi_do_op(struct nxp_fspi *f, const struct spi_mem_op *op) 874{ 875 void __iomem *base = f->iobase; 876 int seqnum = 0; 877 int err = 0; 878 u32 reg; 879 880 reg = fspi_readl(f, base + FSPI_IPRXFCR); 881 /* invalid RXFIFO first */ 882 reg &= ~FSPI_IPRXFCR_DMA_EN; 883 reg = reg | FSPI_IPRXFCR_CLR; 884 fspi_writel(f, reg, base + FSPI_IPRXFCR); 885 886 init_completion(&f->c); 887 888 fspi_writel(f, op->addr.val, base + FSPI_IPCR0); 889 /* 890 * Always start the sequence at the same index since we update 891 * the LUT at each exec_op() call. And also specify the DATA 892 * length, since it's has not been specified in the LUT. 893 */ 894 fspi_writel(f, op->data.nbytes | 895 (SEQID_LUT << FSPI_IPCR1_SEQID_SHIFT) | 896 (seqnum << FSPI_IPCR1_SEQNUM_SHIFT), 897 base + FSPI_IPCR1); 898 899 /* Trigger the LUT now. */ 900 fspi_writel(f, FSPI_IPCMD_TRG, base + FSPI_IPCMD); 901 902 /* Wait for the interrupt. */ 903 if (!wait_for_completion_timeout(&f->c, msecs_to_jiffies(1000))) 904 err = -ETIMEDOUT; 905 906 /* Invoke IP data read, if request is of data read. */ 907 if (!err && op->data.nbytes && op->data.dir == SPI_MEM_DATA_IN) 908 nxp_fspi_read_rxfifo(f, op); 909 910 return err; 911} 912 913static int nxp_fspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) 914{ 915 struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->controller); 916 int err = 0; 917 918 mutex_lock(&f->lock); 919 920 /* Wait for controller being ready. */ 921 err = fspi_readl_poll_tout(f, f->iobase + FSPI_STS0, 922 FSPI_STS0_ARB_IDLE, 1, POLL_TOUT, true); 923 WARN_ON(err); 924 925 nxp_fspi_select_mem(f, mem->spi); 926 927 nxp_fspi_prepare_lut(f, op); 928 /* 929 * If we have large chunks of data, we read them through the AHB bus by 930 * accessing the mapped memory. In all other cases we use IP commands 931 * to access the flash. Read via AHB bus may be corrupted due to 932 * existence of an errata and therefore discard AHB read in such cases. 933 */ 934 if (op->data.nbytes > (f->devtype_data->rxfifo - 4) && 935 op->data.dir == SPI_MEM_DATA_IN && 936 !needs_ip_only(f)) { 937 err = nxp_fspi_read_ahb(f, op); 938 } else { 939 if (op->data.nbytes && op->data.dir == SPI_MEM_DATA_OUT) 940 nxp_fspi_fill_txfifo(f, op); 941 942 err = nxp_fspi_do_op(f, op); 943 } 944 945 /* Invalidate the data in the AHB buffer. */ 946 nxp_fspi_invalid(f); 947 948 mutex_unlock(&f->lock); 949 950 return err; 951} 952 953static int nxp_fspi_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op) 954{ 955 struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->controller); 956 957 if (op->data.dir == SPI_MEM_DATA_OUT) { 958 if (op->data.nbytes > f->devtype_data->txfifo) 959 op->data.nbytes = f->devtype_data->txfifo; 960 } else { 961 if (op->data.nbytes > f->devtype_data->ahb_buf_size) 962 op->data.nbytes = f->devtype_data->ahb_buf_size; 963 else if (op->data.nbytes > (f->devtype_data->rxfifo - 4)) 964 op->data.nbytes = ALIGN_DOWN(op->data.nbytes, 8); 965 } 966 967 /* Limit data bytes to RX FIFO in case of IP read only */ 968 if (op->data.dir == SPI_MEM_DATA_IN && 969 needs_ip_only(f) && 970 op->data.nbytes > f->devtype_data->rxfifo) 971 op->data.nbytes = f->devtype_data->rxfifo; 972 973 return 0; 974} 975 976static void erratum_err050568(struct nxp_fspi *f) 977{ 978 static const struct soc_device_attribute ls1028a_soc_attr[] = { 979 { .family = "QorIQ LS1028A" }, 980 { /* sentinel */ } 981 }; 982 struct regmap *map; 983 u32 val, sys_pll_ratio; 984 int ret; 985 986 /* Check for LS1028A family */ 987 if (!soc_device_match(ls1028a_soc_attr)) { 988 dev_dbg(f->dev, "Errata applicable only for LS1028A\n"); 989 return; 990 } 991 992 map = syscon_regmap_lookup_by_compatible("fsl,ls1028a-dcfg"); 993 if (IS_ERR(map)) { 994 dev_err(f->dev, "No syscon regmap\n"); 995 goto err; 996 } 997 998 ret = regmap_read(map, DCFG_RCWSR1, &val); 999 if (ret < 0) 1000 goto err; 1001 1002 sys_pll_ratio = FIELD_GET(SYS_PLL_RAT, val); 1003 dev_dbg(f->dev, "val: 0x%08x, sys_pll_ratio: %d\n", val, sys_pll_ratio); 1004 1005 /* Use IP bus only if platform clock is 300MHz */ 1006 if (sys_pll_ratio == 3) 1007 f->devtype_data->quirks |= FSPI_QUIRK_USE_IP_ONLY; 1008 1009 return; 1010 1011err: 1012 dev_err(f->dev, "Errata cannot be executed. Read via IP bus may not work\n"); 1013} 1014 1015static int nxp_fspi_default_setup(struct nxp_fspi *f) 1016{ 1017 void __iomem *base = f->iobase; 1018 int ret, i; 1019 u32 reg; 1020 1021 /* disable and unprepare clock to avoid glitch pass to controller */ 1022 nxp_fspi_clk_disable_unprep(f); 1023 1024 /* the default frequency, we will change it later if necessary. */ 1025 ret = clk_set_rate(f->clk, 20000000); 1026 if (ret) 1027 return ret; 1028 1029 ret = nxp_fspi_clk_prep_enable(f); 1030 if (ret) 1031 return ret; 1032 1033 /* 1034 * ERR050568: Flash access by FlexSPI AHB command may not work with 1035 * platform frequency equal to 300 MHz on LS1028A. 1036 * LS1028A reuses LX2160A compatible entry. Make errata applicable for 1037 * Layerscape LS1028A platform. 1038 */ 1039 if (of_device_is_compatible(f->dev->of_node, "nxp,lx2160a-fspi")) 1040 erratum_err050568(f); 1041 1042 /* Reset the module */ 1043 /* w1c register, wait unit clear */ 1044 ret = fspi_readl_poll_tout(f, f->iobase + FSPI_MCR0, 1045 FSPI_MCR0_SWRST, 0, POLL_TOUT, false); 1046 WARN_ON(ret); 1047 1048 /* Disable the module */ 1049 fspi_writel(f, FSPI_MCR0_MDIS, base + FSPI_MCR0); 1050 1051 /* 1052 * Config the DLL register to default value, enable the target clock delay 1053 * line delay cell override mode, and use 1 fixed delay cell in DLL delay 1054 * chain, this is the suggested setting when clock rate < 100MHz. 1055 */ 1056 fspi_writel(f, FSPI_DLLACR_OVRDEN, base + FSPI_DLLACR); 1057 fspi_writel(f, FSPI_DLLBCR_OVRDEN, base + FSPI_DLLBCR); 1058 1059 /* enable module */ 1060 fspi_writel(f, FSPI_MCR0_AHB_TIMEOUT(0xFF) | 1061 FSPI_MCR0_IP_TIMEOUT(0xFF) | (u32) FSPI_MCR0_OCTCOMB_EN, 1062 base + FSPI_MCR0); 1063 1064 /* 1065 * Disable same device enable bit and configure all target devices 1066 * independently. 1067 */ 1068 reg = fspi_readl(f, f->iobase + FSPI_MCR2); 1069 reg = reg & ~(FSPI_MCR2_SAMEDEVICEEN); 1070 fspi_writel(f, reg, base + FSPI_MCR2); 1071 1072 /* AHB configuration for access buffer 0~7. */ 1073 for (i = 0; i < 7; i++) 1074 fspi_writel(f, 0, base + FSPI_AHBRX_BUF0CR0 + 4 * i); 1075 1076 /* 1077 * Set ADATSZ with the maximum AHB buffer size to improve the read 1078 * performance. 1079 */ 1080 fspi_writel(f, (f->devtype_data->ahb_buf_size / 8 | 1081 FSPI_AHBRXBUF0CR7_PREF), base + FSPI_AHBRX_BUF7CR0); 1082 1083 /* prefetch and no start address alignment limitation */ 1084 fspi_writel(f, FSPI_AHBCR_PREF_EN | FSPI_AHBCR_RDADDROPT, 1085 base + FSPI_AHBCR); 1086 1087 /* Reset the FLSHxCR1 registers. */ 1088 reg = FSPI_FLSHXCR1_TCSH(0x3) | FSPI_FLSHXCR1_TCSS(0x3); 1089 fspi_writel(f, reg, base + FSPI_FLSHA1CR1); 1090 fspi_writel(f, reg, base + FSPI_FLSHA2CR1); 1091 fspi_writel(f, reg, base + FSPI_FLSHB1CR1); 1092 fspi_writel(f, reg, base + FSPI_FLSHB2CR1); 1093 1094 /* AHB Read - Set lut sequence ID for all CS. */ 1095 fspi_writel(f, SEQID_LUT, base + FSPI_FLSHA1CR2); 1096 fspi_writel(f, SEQID_LUT, base + FSPI_FLSHA2CR2); 1097 fspi_writel(f, SEQID_LUT, base + FSPI_FLSHB1CR2); 1098 fspi_writel(f, SEQID_LUT, base + FSPI_FLSHB2CR2); 1099 1100 f->selected = -1; 1101 1102 /* enable the interrupt */ 1103 fspi_writel(f, FSPI_INTEN_IPCMDDONE, base + FSPI_INTEN); 1104 1105 return 0; 1106} 1107 1108static const char *nxp_fspi_get_name(struct spi_mem *mem) 1109{ 1110 struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->controller); 1111 struct device *dev = &mem->spi->dev; 1112 const char *name; 1113 1114 // Set custom name derived from the platform_device of the controller. 1115 if (of_get_available_child_count(f->dev->of_node) == 1) 1116 return dev_name(f->dev); 1117 1118 name = devm_kasprintf(dev, GFP_KERNEL, 1119 "%s-%d", dev_name(f->dev), 1120 spi_get_chipselect(mem->spi, 0)); 1121 1122 if (!name) { 1123 dev_err(dev, "failed to get memory for custom flash name\n"); 1124 return ERR_PTR(-ENOMEM); 1125 } 1126 1127 return name; 1128} 1129 1130static const struct spi_controller_mem_ops nxp_fspi_mem_ops = { 1131 .adjust_op_size = nxp_fspi_adjust_op_size, 1132 .supports_op = nxp_fspi_supports_op, 1133 .exec_op = nxp_fspi_exec_op, 1134 .get_name = nxp_fspi_get_name, 1135}; 1136 1137static int nxp_fspi_probe(struct platform_device *pdev) 1138{ 1139 struct spi_controller *ctlr; 1140 struct device *dev = &pdev->dev; 1141 struct device_node *np = dev->of_node; 1142 struct resource *res; 1143 struct nxp_fspi *f; 1144 int ret; 1145 u32 reg; 1146 1147 ctlr = spi_alloc_host(&pdev->dev, sizeof(*f)); 1148 if (!ctlr) 1149 return -ENOMEM; 1150 1151 ctlr->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD | SPI_RX_OCTAL | 1152 SPI_TX_DUAL | SPI_TX_QUAD | SPI_TX_OCTAL; 1153 1154 f = spi_controller_get_devdata(ctlr); 1155 f->dev = dev; 1156 f->devtype_data = (struct nxp_fspi_devtype_data *)device_get_match_data(dev); 1157 if (!f->devtype_data) { 1158 ret = -ENODEV; 1159 goto err_put_ctrl; 1160 } 1161 1162 platform_set_drvdata(pdev, f); 1163 1164 /* find the resources - configuration register address space */ 1165 if (is_acpi_node(dev_fwnode(f->dev))) 1166 f->iobase = devm_platform_ioremap_resource(pdev, 0); 1167 else 1168 f->iobase = devm_platform_ioremap_resource_byname(pdev, "fspi_base"); 1169 1170 if (IS_ERR(f->iobase)) { 1171 ret = PTR_ERR(f->iobase); 1172 goto err_put_ctrl; 1173 } 1174 1175 /* find the resources - controller memory mapped space */ 1176 if (is_acpi_node(dev_fwnode(f->dev))) 1177 res = platform_get_resource(pdev, IORESOURCE_MEM, 1); 1178 else 1179 res = platform_get_resource_byname(pdev, 1180 IORESOURCE_MEM, "fspi_mmap"); 1181 1182 if (!res) { 1183 ret = -ENODEV; 1184 goto err_put_ctrl; 1185 } 1186 1187 /* assign memory mapped starting address and mapped size. */ 1188 f->memmap_phy = res->start; 1189 f->memmap_phy_size = resource_size(res); 1190 1191 /* find the clocks */ 1192 if (dev_of_node(&pdev->dev)) { 1193 f->clk_en = devm_clk_get(dev, "fspi_en"); 1194 if (IS_ERR(f->clk_en)) { 1195 ret = PTR_ERR(f->clk_en); 1196 goto err_put_ctrl; 1197 } 1198 1199 f->clk = devm_clk_get(dev, "fspi"); 1200 if (IS_ERR(f->clk)) { 1201 ret = PTR_ERR(f->clk); 1202 goto err_put_ctrl; 1203 } 1204 1205 ret = nxp_fspi_clk_prep_enable(f); 1206 if (ret) { 1207 dev_err(dev, "can not enable the clock\n"); 1208 goto err_put_ctrl; 1209 } 1210 } 1211 1212 /* Clear potential interrupts */ 1213 reg = fspi_readl(f, f->iobase + FSPI_INTR); 1214 if (reg) 1215 fspi_writel(f, reg, f->iobase + FSPI_INTR); 1216 1217 /* find the irq */ 1218 ret = platform_get_irq(pdev, 0); 1219 if (ret < 0) 1220 goto err_disable_clk; 1221 1222 ret = devm_request_irq(dev, ret, 1223 nxp_fspi_irq_handler, 0, pdev->name, f); 1224 if (ret) { 1225 dev_err(dev, "failed to request irq: %d\n", ret); 1226 goto err_disable_clk; 1227 } 1228 1229 mutex_init(&f->lock); 1230 1231 ctlr->bus_num = -1; 1232 ctlr->num_chipselect = NXP_FSPI_MAX_CHIPSELECT; 1233 ctlr->mem_ops = &nxp_fspi_mem_ops; 1234 1235 nxp_fspi_default_setup(f); 1236 1237 ctlr->dev.of_node = np; 1238 1239 ret = devm_spi_register_controller(&pdev->dev, ctlr); 1240 if (ret) 1241 goto err_destroy_mutex; 1242 1243 return 0; 1244 1245err_destroy_mutex: 1246 mutex_destroy(&f->lock); 1247 1248err_disable_clk: 1249 nxp_fspi_clk_disable_unprep(f); 1250 1251err_put_ctrl: 1252 spi_controller_put(ctlr); 1253 1254 dev_err(dev, "NXP FSPI probe failed\n"); 1255 return ret; 1256} 1257 1258static void nxp_fspi_remove(struct platform_device *pdev) 1259{ 1260 struct nxp_fspi *f = platform_get_drvdata(pdev); 1261 1262 /* disable the hardware */ 1263 fspi_writel(f, FSPI_MCR0_MDIS, f->iobase + FSPI_MCR0); 1264 1265 nxp_fspi_clk_disable_unprep(f); 1266 1267 mutex_destroy(&f->lock); 1268 1269 if (f->ahb_addr) 1270 iounmap(f->ahb_addr); 1271} 1272 1273static int nxp_fspi_suspend(struct device *dev) 1274{ 1275 return 0; 1276} 1277 1278static int nxp_fspi_resume(struct device *dev) 1279{ 1280 struct nxp_fspi *f = dev_get_drvdata(dev); 1281 1282 nxp_fspi_default_setup(f); 1283 1284 return 0; 1285} 1286 1287static const struct of_device_id nxp_fspi_dt_ids[] = { 1288 { .compatible = "nxp,lx2160a-fspi", .data = (void *)&lx2160a_data, }, 1289 { .compatible = "nxp,imx8mm-fspi", .data = (void *)&imx8mm_data, }, 1290 { .compatible = "nxp,imx8mp-fspi", .data = (void *)&imx8mm_data, }, 1291 { .compatible = "nxp,imx8qxp-fspi", .data = (void *)&imx8qxp_data, }, 1292 { .compatible = "nxp,imx8dxl-fspi", .data = (void *)&imx8dxl_data, }, 1293 { /* sentinel */ } 1294}; 1295MODULE_DEVICE_TABLE(of, nxp_fspi_dt_ids); 1296 1297#ifdef CONFIG_ACPI 1298static const struct acpi_device_id nxp_fspi_acpi_ids[] = { 1299 { "NXP0009", .driver_data = (kernel_ulong_t)&lx2160a_data, }, 1300 {} 1301}; 1302MODULE_DEVICE_TABLE(acpi, nxp_fspi_acpi_ids); 1303#endif 1304 1305static const struct dev_pm_ops nxp_fspi_pm_ops = { 1306 .suspend = nxp_fspi_suspend, 1307 .resume = nxp_fspi_resume, 1308}; 1309 1310static struct platform_driver nxp_fspi_driver = { 1311 .driver = { 1312 .name = "nxp-fspi", 1313 .of_match_table = nxp_fspi_dt_ids, 1314 .acpi_match_table = ACPI_PTR(nxp_fspi_acpi_ids), 1315 .pm = &nxp_fspi_pm_ops, 1316 }, 1317 .probe = nxp_fspi_probe, 1318 .remove_new = nxp_fspi_remove, 1319}; 1320module_platform_driver(nxp_fspi_driver); 1321 1322MODULE_DESCRIPTION("NXP FSPI Controller Driver"); 1323MODULE_AUTHOR("NXP Semiconductor"); 1324MODULE_AUTHOR("Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>"); 1325MODULE_AUTHOR("Boris Brezillon <bbrezillon@kernel.org>"); 1326MODULE_AUTHOR("Frieder Schrempf <frieder.schrempf@kontron.de>"); 1327MODULE_LICENSE("GPL v2"); 1328