1/* SPDX-License-Identifier: GPL-2.0 */
2#ifndef _SCSI_LOGGING_H
3#define _SCSI_LOGGING_H
4
5
6/*
7 * This defines the scsi logging feature.  It is a means by which the user can
8 * select how much information they get about various goings on, and it can be
9 * really useful for fault tracing.  The logging word is divided into 10 3-bit
10 * bitfields, each of which describes a loglevel.  The division of things is
11 * somewhat arbitrary, and the division of the word could be changed if it
12 * were really needed for any reason.  The numbers below are the only place
13 * where these are specified.  For a first go-around, 3 bits is more than
14 * enough, since this gives 8 levels of logging (really 7, since 0 is always
15 * off).  Cutting to 2 bits might be wise at some point.
16 */
17
18#define SCSI_LOG_ERROR_SHIFT              0
19#define SCSI_LOG_TIMEOUT_SHIFT            3
20#define SCSI_LOG_SCAN_SHIFT               6
21#define SCSI_LOG_MLQUEUE_SHIFT            9
22#define SCSI_LOG_MLCOMPLETE_SHIFT         12
23#define SCSI_LOG_LLQUEUE_SHIFT            15
24#define SCSI_LOG_LLCOMPLETE_SHIFT         18
25#define SCSI_LOG_HLQUEUE_SHIFT            21
26#define SCSI_LOG_HLCOMPLETE_SHIFT         24
27#define SCSI_LOG_IOCTL_SHIFT              27
28
29#define SCSI_LOG_ERROR_BITS               3
30#define SCSI_LOG_TIMEOUT_BITS             3
31#define SCSI_LOG_SCAN_BITS                3
32#define SCSI_LOG_MLQUEUE_BITS             3
33#define SCSI_LOG_MLCOMPLETE_BITS          3
34#define SCSI_LOG_LLQUEUE_BITS             3
35#define SCSI_LOG_LLCOMPLETE_BITS          3
36#define SCSI_LOG_HLQUEUE_BITS             3
37#define SCSI_LOG_HLCOMPLETE_BITS          3
38#define SCSI_LOG_IOCTL_BITS               3
39
40extern unsigned int scsi_logging_level;
41
42#ifdef CONFIG_SCSI_LOGGING
43
44#define SCSI_LOG_LEVEL(SHIFT, BITS)				\
45        ((scsi_logging_level >> (SHIFT)) & ((1 << (BITS)) - 1))
46
47#define SCSI_CHECK_LOGGING(SHIFT, BITS, LEVEL, CMD)		\
48do {								\
49        if (unlikely((SCSI_LOG_LEVEL(SHIFT, BITS)) > (LEVEL)))	\
50		do {						\
51			CMD;					\
52		} while (0);					\
53} while (0)
54#else
55#define SCSI_LOG_LEVEL(SHIFT, BITS) 0
56#define SCSI_CHECK_LOGGING(SHIFT, BITS, LEVEL, CMD) do { } while (0)
57#endif /* CONFIG_SCSI_LOGGING */
58
59/*
60 * These are the macros that are actually used throughout the code to
61 * log events.  If logging isn't enabled, they are no-ops and will be
62 * completely absent from the user's code.
63 */
64#define SCSI_LOG_ERROR_RECOVERY(LEVEL,CMD)  \
65        SCSI_CHECK_LOGGING(SCSI_LOG_ERROR_SHIFT, SCSI_LOG_ERROR_BITS, LEVEL,CMD);
66#define SCSI_LOG_TIMEOUT(LEVEL,CMD)  \
67        SCSI_CHECK_LOGGING(SCSI_LOG_TIMEOUT_SHIFT, SCSI_LOG_TIMEOUT_BITS, LEVEL,CMD);
68#define SCSI_LOG_SCAN_BUS(LEVEL,CMD)  \
69        SCSI_CHECK_LOGGING(SCSI_LOG_SCAN_SHIFT, SCSI_LOG_SCAN_BITS, LEVEL,CMD);
70#define SCSI_LOG_MLQUEUE(LEVEL,CMD)  \
71        SCSI_CHECK_LOGGING(SCSI_LOG_MLQUEUE_SHIFT, SCSI_LOG_MLQUEUE_BITS, LEVEL,CMD);
72#define SCSI_LOG_MLCOMPLETE(LEVEL,CMD)  \
73        SCSI_CHECK_LOGGING(SCSI_LOG_MLCOMPLETE_SHIFT, SCSI_LOG_MLCOMPLETE_BITS, LEVEL,CMD);
74#define SCSI_LOG_LLQUEUE(LEVEL,CMD)  \
75        SCSI_CHECK_LOGGING(SCSI_LOG_LLQUEUE_SHIFT, SCSI_LOG_LLQUEUE_BITS, LEVEL,CMD);
76#define SCSI_LOG_LLCOMPLETE(LEVEL,CMD)  \
77        SCSI_CHECK_LOGGING(SCSI_LOG_LLCOMPLETE_SHIFT, SCSI_LOG_LLCOMPLETE_BITS, LEVEL,CMD);
78#define SCSI_LOG_HLQUEUE(LEVEL,CMD)  \
79        SCSI_CHECK_LOGGING(SCSI_LOG_HLQUEUE_SHIFT, SCSI_LOG_HLQUEUE_BITS, LEVEL,CMD);
80#define SCSI_LOG_HLCOMPLETE(LEVEL,CMD)  \
81        SCSI_CHECK_LOGGING(SCSI_LOG_HLCOMPLETE_SHIFT, SCSI_LOG_HLCOMPLETE_BITS, LEVEL,CMD);
82#define SCSI_LOG_IOCTL(LEVEL,CMD)  \
83        SCSI_CHECK_LOGGING(SCSI_LOG_IOCTL_SHIFT, SCSI_LOG_IOCTL_BITS, LEVEL,CMD);
84
85#endif /* _SCSI_LOGGING_H */
86