1/* 2 * Product specific probe and attach routines for: 3 * aic7901 and aic7902 SCSI controllers 4 * 5 * Copyright (c) 1994-2001 Justin T. Gibbs. 6 * Copyright (c) 2000-2002 Adaptec Inc. 7 * All rights reserved. 8 * 9 * Redistribution and use in source and binary forms, with or without 10 * modification, are permitted provided that the following conditions 11 * are met: 12 * 1. Redistributions of source code must retain the above copyright 13 * notice, this list of conditions, and the following disclaimer, 14 * without modification. 15 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 16 * substantially similar to the "NO WARRANTY" disclaimer below 17 * ("Disclaimer") and any redistribution must be conditioned upon 18 * including a substantially similar Disclaimer requirement for further 19 * binary redistribution. 20 * 3. Neither the names of the above-listed copyright holders nor the names 21 * of any contributors may be used to endorse or promote products derived 22 * from this software without specific prior written permission. 23 * 24 * Alternatively, this software may be distributed under the terms of the 25 * GNU General Public License ("GPL") version 2 as published by the Free 26 * Software Foundation. 27 * 28 * NO WARRANTY 29 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 30 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 31 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR 32 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 33 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 34 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 35 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 36 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 37 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 38 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 39 * POSSIBILITY OF SUCH DAMAGES. 40 * 41 * $Id: //depot/aic7xxx/aic7xxx/aic79xx_pci.c#92 $ 42 */ 43 44#include "aic79xx_osm.h" 45#include "aic79xx_inline.h" 46#include "aic79xx_pci.h" 47 48static inline uint64_t 49ahd_compose_id(u_int device, u_int vendor, u_int subdevice, u_int subvendor) 50{ 51 uint64_t id; 52 53 id = subvendor 54 | (subdevice << 16) 55 | ((uint64_t)vendor << 32) 56 | ((uint64_t)device << 48); 57 58 return (id); 59} 60 61#define ID_AIC7902_PCI_REV_A4 0x3 62#define ID_AIC7902_PCI_REV_B0 0x10 63#define SUBID_HP 0x0E11 64 65#define DEVID_9005_HOSTRAID(id) ((id) & 0x80) 66 67#define DEVID_9005_TYPE(id) ((id) & 0xF) 68#define DEVID_9005_TYPE_HBA 0x0 /* Standard Card */ 69#define DEVID_9005_TYPE_HBA_2EXT 0x1 /* 2 External Ports */ 70#define DEVID_9005_TYPE_IROC 0x8 /* Raid(0,1,10) Card */ 71#define DEVID_9005_TYPE_MB 0xF /* On Motherboard */ 72 73#define DEVID_9005_MFUNC(id) ((id) & 0x10) 74 75#define DEVID_9005_PACKETIZED(id) ((id) & 0x8000) 76 77#define SUBID_9005_TYPE(id) ((id) & 0xF) 78#define SUBID_9005_TYPE_HBA 0x0 /* Standard Card */ 79#define SUBID_9005_TYPE_MB 0xF /* On Motherboard */ 80 81#define SUBID_9005_AUTOTERM(id) (((id) & 0x10) == 0) 82 83#define SUBID_9005_LEGACYCONN_FUNC(id) ((id) & 0x20) 84 85#define SUBID_9005_SEEPTYPE(id) (((id) & 0x0C0) >> 6) 86#define SUBID_9005_SEEPTYPE_NONE 0x0 87#define SUBID_9005_SEEPTYPE_4K 0x1 88 89static ahd_device_setup_t ahd_aic7901_setup; 90static ahd_device_setup_t ahd_aic7901A_setup; 91static ahd_device_setup_t ahd_aic7902_setup; 92static ahd_device_setup_t ahd_aic790X_setup; 93 94static const struct ahd_pci_identity ahd_pci_ident_table[] = 95{ 96 /* aic7901 based controllers */ 97 { 98 ID_AHA_29320A, 99 ID_ALL_MASK, 100 "Adaptec 29320A Ultra320 SCSI adapter", 101 ahd_aic7901_setup 102 }, 103 { 104 ID_AHA_29320ALP, 105 ID_ALL_MASK, 106 "Adaptec 29320ALP PCIx Ultra320 SCSI adapter", 107 ahd_aic7901_setup 108 }, 109 { 110 ID_AHA_29320LPE, 111 ID_ALL_MASK, 112 "Adaptec 29320LPE PCIe Ultra320 SCSI adapter", 113 ahd_aic7901_setup 114 }, 115 /* aic7901A based controllers */ 116 { 117 ID_AHA_29320LP, 118 ID_ALL_MASK, 119 "Adaptec 29320LP Ultra320 SCSI adapter", 120 ahd_aic7901A_setup 121 }, 122 /* aic7902 based controllers */ 123 { 124 ID_AHA_29320, 125 ID_ALL_MASK, 126 "Adaptec 29320 Ultra320 SCSI adapter", 127 ahd_aic7902_setup 128 }, 129 { 130 ID_AHA_29320B, 131 ID_ALL_MASK, 132 "Adaptec 29320B Ultra320 SCSI adapter", 133 ahd_aic7902_setup 134 }, 135 { 136 ID_AHA_39320, 137 ID_ALL_MASK, 138 "Adaptec 39320 Ultra320 SCSI adapter", 139 ahd_aic7902_setup 140 }, 141 { 142 ID_AHA_39320_B, 143 ID_ALL_MASK, 144 "Adaptec 39320 Ultra320 SCSI adapter", 145 ahd_aic7902_setup 146 }, 147 { 148 ID_AHA_39320_B_DELL, 149 ID_ALL_MASK, 150 "Adaptec (Dell OEM) 39320 Ultra320 SCSI adapter", 151 ahd_aic7902_setup 152 }, 153 { 154 ID_AHA_39320A, 155 ID_ALL_MASK, 156 "Adaptec 39320A Ultra320 SCSI adapter", 157 ahd_aic7902_setup 158 }, 159 { 160 ID_AHA_39320D, 161 ID_ALL_MASK, 162 "Adaptec 39320D Ultra320 SCSI adapter", 163 ahd_aic7902_setup 164 }, 165 { 166 ID_AHA_39320D_HP, 167 ID_ALL_MASK, 168 "Adaptec (HP OEM) 39320D Ultra320 SCSI adapter", 169 ahd_aic7902_setup 170 }, 171 { 172 ID_AHA_39320D_B, 173 ID_ALL_MASK, 174 "Adaptec 39320D Ultra320 SCSI adapter", 175 ahd_aic7902_setup 176 }, 177 { 178 ID_AHA_39320D_B_HP, 179 ID_ALL_MASK, 180 "Adaptec (HP OEM) 39320D Ultra320 SCSI adapter", 181 ahd_aic7902_setup 182 }, 183 /* Generic chip probes for devices we don't know 'exactly' */ 184 { 185 ID_AIC7901 & ID_9005_GENERIC_MASK, 186 ID_9005_GENERIC_MASK, 187 "Adaptec AIC7901 Ultra320 SCSI adapter", 188 ahd_aic7901_setup 189 }, 190 { 191 ID_AIC7901A & ID_DEV_VENDOR_MASK, 192 ID_DEV_VENDOR_MASK, 193 "Adaptec AIC7901A Ultra320 SCSI adapter", 194 ahd_aic7901A_setup 195 }, 196 { 197 ID_AIC7902 & ID_9005_GENERIC_MASK, 198 ID_9005_GENERIC_MASK, 199 "Adaptec AIC7902 Ultra320 SCSI adapter", 200 ahd_aic7902_setup 201 } 202}; 203 204static const u_int ahd_num_pci_devs = ARRAY_SIZE(ahd_pci_ident_table); 205 206#define DEVCONFIG 0x40 207#define PCIXINITPAT 0x0000E000ul 208#define PCIXINIT_PCI33_66 0x0000E000ul 209#define PCIXINIT_PCIX50_66 0x0000C000ul 210#define PCIXINIT_PCIX66_100 0x0000A000ul 211#define PCIXINIT_PCIX100_133 0x00008000ul 212#define PCI_BUS_MODES_INDEX(devconfig) \ 213 (((devconfig) & PCIXINITPAT) >> 13) 214static const char *pci_bus_modes[] = 215{ 216 "PCI bus mode unknown", 217 "PCI bus mode unknown", 218 "PCI bus mode unknown", 219 "PCI bus mode unknown", 220 "PCI-X 101-133MHz", 221 "PCI-X 67-100MHz", 222 "PCI-X 50-66MHz", 223 "PCI 33 or 66MHz" 224}; 225 226#define TESTMODE 0x00000800ul 227#define IRDY_RST 0x00000200ul 228#define FRAME_RST 0x00000100ul 229#define PCI64BIT 0x00000080ul 230#define MRDCEN 0x00000040ul 231#define ENDIANSEL 0x00000020ul 232#define MIXQWENDIANEN 0x00000008ul 233#define DACEN 0x00000004ul 234#define STPWLEVEL 0x00000002ul 235#define QWENDIANSEL 0x00000001ul 236 237#define DEVCONFIG1 0x44 238#define PREQDIS 0x01 239 240#define CSIZE_LATTIME 0x0c 241#define CACHESIZE 0x000000fful 242#define LATTIME 0x0000ff00ul 243 244static int ahd_check_extport(struct ahd_softc *ahd); 245static void ahd_configure_termination(struct ahd_softc *ahd, 246 u_int adapter_control); 247static void ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat); 248static void ahd_pci_intr(struct ahd_softc *ahd); 249 250const struct ahd_pci_identity * 251ahd_find_pci_device(ahd_dev_softc_t pci) 252{ 253 uint64_t full_id; 254 uint16_t device; 255 uint16_t vendor; 256 uint16_t subdevice; 257 uint16_t subvendor; 258 const struct ahd_pci_identity *entry; 259 u_int i; 260 261 vendor = ahd_pci_read_config(pci, PCIR_DEVVENDOR, /*bytes*/2); 262 device = ahd_pci_read_config(pci, PCIR_DEVICE, /*bytes*/2); 263 subvendor = ahd_pci_read_config(pci, PCI_SUBSYSTEM_VENDOR_ID, /*bytes*/2); 264 subdevice = ahd_pci_read_config(pci, PCI_SUBSYSTEM_ID, /*bytes*/2); 265 full_id = ahd_compose_id(device, 266 vendor, 267 subdevice, 268 subvendor); 269 270 /* 271 * Controllers, mask out the IROC/HostRAID bit 272 */ 273 274 full_id &= ID_ALL_IROC_MASK; 275 276 for (i = 0; i < ahd_num_pci_devs; i++) { 277 entry = &ahd_pci_ident_table[i]; 278 if (entry->full_id == (full_id & entry->id_mask)) { 279 /* Honor exclusion entries. */ 280 if (entry->name == NULL) 281 return (NULL); 282 return (entry); 283 } 284 } 285 return (NULL); 286} 287 288int 289ahd_pci_config(struct ahd_softc *ahd, const struct ahd_pci_identity *entry) 290{ 291 u_int command; 292 uint32_t devconfig; 293 uint16_t subvendor; 294 int error; 295 296 ahd->description = entry->name; 297 /* 298 * Record if this is an HP board. 299 */ 300 subvendor = ahd_pci_read_config(ahd->dev_softc, 301 PCI_SUBSYSTEM_VENDOR_ID, /*bytes*/2); 302 if (subvendor == SUBID_HP) 303 ahd->flags |= AHD_HP_BOARD; 304 305 error = entry->setup(ahd); 306 if (error != 0) 307 return (error); 308 309 devconfig = ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); 310 if ((devconfig & PCIXINITPAT) == PCIXINIT_PCI33_66) { 311 ahd->chip |= AHD_PCI; 312 /* Disable PCIX workarounds when running in PCI mode. */ 313 ahd->bugs &= ~AHD_PCIX_BUG_MASK; 314 } else { 315 ahd->chip |= AHD_PCIX; 316 } 317 ahd->bus_description = pci_bus_modes[PCI_BUS_MODES_INDEX(devconfig)]; 318 319 ahd_power_state_change(ahd, AHD_POWER_STATE_D0); 320 321 error = ahd_pci_map_registers(ahd); 322 if (error != 0) 323 return (error); 324 325 /* 326 * If we need to support high memory, enable dual 327 * address cycles. This bit must be set to enable 328 * high address bit generation even if we are on a 329 * 64bit bus (PCI64BIT set in devconfig). 330 */ 331 if ((ahd->flags & (AHD_39BIT_ADDRESSING|AHD_64BIT_ADDRESSING)) != 0) { 332 if (bootverbose) 333 printk("%s: Enabling 39Bit Addressing\n", 334 ahd_name(ahd)); 335 devconfig = ahd_pci_read_config(ahd->dev_softc, 336 DEVCONFIG, /*bytes*/4); 337 devconfig |= DACEN; 338 ahd_pci_write_config(ahd->dev_softc, DEVCONFIG, 339 devconfig, /*bytes*/4); 340 } 341 342 /* Ensure busmastering is enabled */ 343 command = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2); 344 command |= PCIM_CMD_BUSMASTEREN; 345 ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, command, /*bytes*/2); 346 347 error = ahd_softc_init(ahd); 348 if (error != 0) 349 return (error); 350 351 ahd->bus_intr = ahd_pci_intr; 352 353 error = ahd_reset(ahd, /*reinit*/FALSE); 354 if (error != 0) 355 return (ENXIO); 356 357 ahd->pci_cachesize = 358 ahd_pci_read_config(ahd->dev_softc, CSIZE_LATTIME, 359 /*bytes*/1) & CACHESIZE; 360 ahd->pci_cachesize *= 4; 361 362 ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); 363 /* See if we have a SEEPROM and perform auto-term */ 364 error = ahd_check_extport(ahd); 365 if (error != 0) 366 return (error); 367 368 /* Core initialization */ 369 error = ahd_init(ahd); 370 if (error != 0) 371 return (error); 372 ahd->init_level++; 373 374 /* 375 * Allow interrupts now that we are completely setup. 376 */ 377 return ahd_pci_map_int(ahd); 378} 379 380void __maybe_unused 381ahd_pci_suspend(struct ahd_softc *ahd) 382{ 383 /* 384 * Save chip register configuration data for chip resets 385 * that occur during runtime and resume events. 386 */ 387 ahd->suspend_state.pci_state.devconfig = 388 ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); 389 ahd->suspend_state.pci_state.command = 390 ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/1); 391 ahd->suspend_state.pci_state.csize_lattime = 392 ahd_pci_read_config(ahd->dev_softc, CSIZE_LATTIME, /*bytes*/1); 393 394} 395 396void __maybe_unused 397ahd_pci_resume(struct ahd_softc *ahd) 398{ 399 ahd_pci_write_config(ahd->dev_softc, DEVCONFIG, 400 ahd->suspend_state.pci_state.devconfig, /*bytes*/4); 401 ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, 402 ahd->suspend_state.pci_state.command, /*bytes*/1); 403 ahd_pci_write_config(ahd->dev_softc, CSIZE_LATTIME, 404 ahd->suspend_state.pci_state.csize_lattime, /*bytes*/1); 405} 406 407/* 408 * Perform some simple tests that should catch situations where 409 * our registers are invalidly mapped. 410 */ 411int 412ahd_pci_test_register_access(struct ahd_softc *ahd) 413{ 414 uint32_t cmd; 415 u_int targpcistat; 416 u_int pci_status1; 417 int error; 418 uint8_t hcntrl; 419 420 error = EIO; 421 422 /* 423 * Enable PCI error interrupt status, but suppress NMIs 424 * generated by SERR raised due to target aborts. 425 */ 426 cmd = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2); 427 ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, 428 cmd & ~PCIM_CMD_SERRESPEN, /*bytes*/2); 429 430 /* 431 * First a simple test to see if any 432 * registers can be read. Reading 433 * HCNTRL has no side effects and has 434 * at least one bit that is guaranteed to 435 * be zero so it is a good register to 436 * use for this test. 437 */ 438 hcntrl = ahd_inb(ahd, HCNTRL); 439 if (hcntrl == 0xFF) 440 goto fail; 441 442 /* 443 * Next create a situation where write combining 444 * or read prefetching could be initiated by the 445 * CPU or host bridge. Our device does not support 446 * either, so look for data corruption and/or flaged 447 * PCI errors. First pause without causing another 448 * chip reset. 449 */ 450 hcntrl &= ~CHIPRST; 451 ahd_outb(ahd, HCNTRL, hcntrl|PAUSE); 452 while (ahd_is_paused(ahd) == 0) 453 ; 454 455 /* Clear any PCI errors that occurred before our driver attached. */ 456 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 457 targpcistat = ahd_inb(ahd, TARGPCISTAT); 458 ahd_outb(ahd, TARGPCISTAT, targpcistat); 459 pci_status1 = ahd_pci_read_config(ahd->dev_softc, 460 PCIR_STATUS + 1, /*bytes*/1); 461 ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, 462 pci_status1, /*bytes*/1); 463 ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); 464 ahd_outb(ahd, CLRINT, CLRPCIINT); 465 466 ahd_outb(ahd, SEQCTL0, PERRORDIS); 467 ahd_outl(ahd, SRAM_BASE, 0x5aa555aa); 468 if (ahd_inl(ahd, SRAM_BASE) != 0x5aa555aa) 469 goto fail; 470 471 if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) { 472 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 473 targpcistat = ahd_inb(ahd, TARGPCISTAT); 474 if ((targpcistat & STA) != 0) 475 goto fail; 476 } 477 478 error = 0; 479 480fail: 481 if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) { 482 483 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 484 targpcistat = ahd_inb(ahd, TARGPCISTAT); 485 486 /* Silently clear any latched errors. */ 487 ahd_outb(ahd, TARGPCISTAT, targpcistat); 488 pci_status1 = ahd_pci_read_config(ahd->dev_softc, 489 PCIR_STATUS + 1, /*bytes*/1); 490 ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, 491 pci_status1, /*bytes*/1); 492 ahd_outb(ahd, CLRINT, CLRPCIINT); 493 } 494 ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS); 495 ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, cmd, /*bytes*/2); 496 return (error); 497} 498 499/* 500 * Check the external port logic for a serial eeprom 501 * and termination/cable detection contrls. 502 */ 503static int 504ahd_check_extport(struct ahd_softc *ahd) 505{ 506 struct vpd_config vpd; 507 struct seeprom_config *sc; 508 u_int adapter_control; 509 int have_seeprom; 510 int error; 511 512 sc = ahd->seep_config; 513 have_seeprom = ahd_acquire_seeprom(ahd); 514 if (have_seeprom) { 515 u_int start_addr; 516 517 /* 518 * Fetch VPD for this function and parse it. 519 */ 520 if (bootverbose) 521 printk("%s: Reading VPD from SEEPROM...", 522 ahd_name(ahd)); 523 524 /* Address is always in units of 16bit words */ 525 start_addr = ((2 * sizeof(*sc)) 526 + (sizeof(vpd) * (ahd->channel - 'A'))) / 2; 527 528 error = ahd_read_seeprom(ahd, (uint16_t *)&vpd, 529 start_addr, sizeof(vpd)/2, 530 /*bytestream*/TRUE); 531 if (error == 0) 532 error = ahd_parse_vpddata(ahd, &vpd); 533 if (bootverbose) 534 printk("%s: VPD parsing %s\n", 535 ahd_name(ahd), 536 error == 0 ? "successful" : "failed"); 537 538 if (bootverbose) 539 printk("%s: Reading SEEPROM...", ahd_name(ahd)); 540 541 /* Address is always in units of 16bit words */ 542 start_addr = (sizeof(*sc) / 2) * (ahd->channel - 'A'); 543 544 error = ahd_read_seeprom(ahd, (uint16_t *)sc, 545 start_addr, sizeof(*sc)/2, 546 /*bytestream*/FALSE); 547 548 if (error != 0) { 549 printk("Unable to read SEEPROM\n"); 550 have_seeprom = 0; 551 } else { 552 have_seeprom = ahd_verify_cksum(sc); 553 554 if (bootverbose) { 555 if (have_seeprom == 0) 556 printk ("checksum error\n"); 557 else 558 printk ("done.\n"); 559 } 560 } 561 ahd_release_seeprom(ahd); 562 } 563 564 if (!have_seeprom) { 565 u_int nvram_scb; 566 567 /* 568 * Pull scratch ram settings and treat them as 569 * if they are the contents of an seeprom if 570 * the 'ADPT', 'BIOS', or 'ASPI' signature is found 571 * in SCB 0xFF. We manually compose the data as 16bit 572 * values to avoid endian issues. 573 */ 574 ahd_set_scbptr(ahd, 0xFF); 575 nvram_scb = ahd_inb_scbram(ahd, SCB_BASE + NVRAM_SCB_OFFSET); 576 if (nvram_scb != 0xFF 577 && ((ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A' 578 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'D' 579 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P' 580 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'T') 581 || (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'B' 582 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'I' 583 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'O' 584 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'S') 585 || (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A' 586 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'S' 587 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P' 588 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'I'))) { 589 uint16_t *sc_data; 590 int i; 591 592 ahd_set_scbptr(ahd, nvram_scb); 593 sc_data = (uint16_t *)sc; 594 for (i = 0; i < 64; i += 2) 595 *sc_data++ = ahd_inw_scbram(ahd, SCB_BASE+i); 596 have_seeprom = ahd_verify_cksum(sc); 597 if (have_seeprom) 598 ahd->flags |= AHD_SCB_CONFIG_USED; 599 } 600 } 601 602#ifdef AHD_DEBUG 603 if (have_seeprom != 0 604 && (ahd_debug & AHD_DUMP_SEEPROM) != 0) { 605 uint16_t *sc_data; 606 int i; 607 608 printk("%s: Seeprom Contents:", ahd_name(ahd)); 609 sc_data = (uint16_t *)sc; 610 for (i = 0; i < (sizeof(*sc)); i += 2) 611 printk("\n\t0x%.4x", sc_data[i]); 612 printk("\n"); 613 } 614#endif 615 616 if (!have_seeprom) { 617 if (bootverbose) 618 printk("%s: No SEEPROM available.\n", ahd_name(ahd)); 619 ahd->flags |= AHD_USEDEFAULTS; 620 error = ahd_default_config(ahd); 621 adapter_control = CFAUTOTERM|CFSEAUTOTERM; 622 kfree(ahd->seep_config); 623 ahd->seep_config = NULL; 624 } else { 625 error = ahd_parse_cfgdata(ahd, sc); 626 adapter_control = sc->adapter_control; 627 } 628 if (error != 0) 629 return (error); 630 631 ahd_configure_termination(ahd, adapter_control); 632 633 return (0); 634} 635 636static void 637ahd_configure_termination(struct ahd_softc *ahd, u_int adapter_control) 638{ 639 int error; 640 u_int sxfrctl1; 641 uint8_t termctl; 642 uint32_t devconfig; 643 644 devconfig = ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); 645 devconfig &= ~STPWLEVEL; 646 if ((ahd->flags & AHD_STPWLEVEL_A) != 0) 647 devconfig |= STPWLEVEL; 648 if (bootverbose) 649 printk("%s: STPWLEVEL is %s\n", 650 ahd_name(ahd), (devconfig & STPWLEVEL) ? "on" : "off"); 651 ahd_pci_write_config(ahd->dev_softc, DEVCONFIG, devconfig, /*bytes*/4); 652 653 /* Make sure current sensing is off. */ 654 if ((ahd->flags & AHD_CURRENT_SENSING) != 0) { 655 (void)ahd_write_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL, 0); 656 } 657 658 /* 659 * Read to sense. Write to set. 660 */ 661 error = ahd_read_flexport(ahd, FLXADDR_TERMCTL, &termctl); 662 if ((adapter_control & CFAUTOTERM) == 0) { 663 if (bootverbose) 664 printk("%s: Manual Primary Termination\n", 665 ahd_name(ahd)); 666 termctl &= ~(FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH); 667 if ((adapter_control & CFSTERM) != 0) 668 termctl |= FLX_TERMCTL_ENPRILOW; 669 if ((adapter_control & CFWSTERM) != 0) 670 termctl |= FLX_TERMCTL_ENPRIHIGH; 671 } else if (error != 0) { 672 printk("%s: Primary Auto-Term Sensing failed! " 673 "Using Defaults.\n", ahd_name(ahd)); 674 termctl = FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH; 675 } 676 677 if ((adapter_control & CFSEAUTOTERM) == 0) { 678 if (bootverbose) 679 printk("%s: Manual Secondary Termination\n", 680 ahd_name(ahd)); 681 termctl &= ~(FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH); 682 if ((adapter_control & CFSELOWTERM) != 0) 683 termctl |= FLX_TERMCTL_ENSECLOW; 684 if ((adapter_control & CFSEHIGHTERM) != 0) 685 termctl |= FLX_TERMCTL_ENSECHIGH; 686 } else if (error != 0) { 687 printk("%s: Secondary Auto-Term Sensing failed! " 688 "Using Defaults.\n", ahd_name(ahd)); 689 termctl |= FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH; 690 } 691 692 /* 693 * Now set the termination based on what we found. 694 */ 695 sxfrctl1 = ahd_inb(ahd, SXFRCTL1) & ~STPWEN; 696 ahd->flags &= ~AHD_TERM_ENB_A; 697 if ((termctl & FLX_TERMCTL_ENPRILOW) != 0) { 698 ahd->flags |= AHD_TERM_ENB_A; 699 sxfrctl1 |= STPWEN; 700 } 701 /* Must set the latch once in order to be effective. */ 702 ahd_outb(ahd, SXFRCTL1, sxfrctl1|STPWEN); 703 ahd_outb(ahd, SXFRCTL1, sxfrctl1); 704 705 error = ahd_write_flexport(ahd, FLXADDR_TERMCTL, termctl); 706 if (error != 0) { 707 printk("%s: Unable to set termination settings!\n", 708 ahd_name(ahd)); 709 } else if (bootverbose) { 710 printk("%s: Primary High byte termination %sabled\n", 711 ahd_name(ahd), 712 (termctl & FLX_TERMCTL_ENPRIHIGH) ? "En" : "Dis"); 713 714 printk("%s: Primary Low byte termination %sabled\n", 715 ahd_name(ahd), 716 (termctl & FLX_TERMCTL_ENPRILOW) ? "En" : "Dis"); 717 718 printk("%s: Secondary High byte termination %sabled\n", 719 ahd_name(ahd), 720 (termctl & FLX_TERMCTL_ENSECHIGH) ? "En" : "Dis"); 721 722 printk("%s: Secondary Low byte termination %sabled\n", 723 ahd_name(ahd), 724 (termctl & FLX_TERMCTL_ENSECLOW) ? "En" : "Dis"); 725 } 726 return; 727} 728 729#define DPE 0x80 730#define SSE 0x40 731#define RMA 0x20 732#define RTA 0x10 733#define STA 0x08 734#define DPR 0x01 735 736static const char *split_status_source[] = 737{ 738 "DFF0", 739 "DFF1", 740 "OVLY", 741 "CMC", 742}; 743 744static const char *pci_status_source[] = 745{ 746 "DFF0", 747 "DFF1", 748 "SG", 749 "CMC", 750 "OVLY", 751 "NONE", 752 "MSI", 753 "TARG" 754}; 755 756static const char *split_status_strings[] = 757{ 758 "%s: Received split response in %s.\n", 759 "%s: Received split completion error message in %s\n", 760 "%s: Receive overrun in %s\n", 761 "%s: Count not complete in %s\n", 762 "%s: Split completion data bucket in %s\n", 763 "%s: Split completion address error in %s\n", 764 "%s: Split completion byte count error in %s\n", 765 "%s: Signaled Target-abort to early terminate a split in %s\n" 766}; 767 768static const char *pci_status_strings[] = 769{ 770 "%s: Data Parity Error has been reported via PERR# in %s\n", 771 "%s: Target initial wait state error in %s\n", 772 "%s: Split completion read data parity error in %s\n", 773 "%s: Split completion address attribute parity error in %s\n", 774 "%s: Received a Target Abort in %s\n", 775 "%s: Received a Master Abort in %s\n", 776 "%s: Signal System Error Detected in %s\n", 777 "%s: Address or Write Phase Parity Error Detected in %s.\n" 778}; 779 780static void 781ahd_pci_intr(struct ahd_softc *ahd) 782{ 783 uint8_t pci_status[8]; 784 ahd_mode_state saved_modes; 785 u_int pci_status1; 786 u_int intstat; 787 u_int i; 788 u_int reg; 789 790 intstat = ahd_inb(ahd, INTSTAT); 791 792 if ((intstat & SPLTINT) != 0) 793 ahd_pci_split_intr(ahd, intstat); 794 795 if ((intstat & PCIINT) == 0) 796 return; 797 798 printk("%s: PCI error Interrupt\n", ahd_name(ahd)); 799 saved_modes = ahd_save_modes(ahd); 800 ahd_dump_card_state(ahd); 801 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 802 for (i = 0, reg = DF0PCISTAT; i < 8; i++, reg++) { 803 804 if (i == 5) 805 continue; 806 pci_status[i] = ahd_inb(ahd, reg); 807 /* Clear latched errors. So our interrupt deasserts. */ 808 ahd_outb(ahd, reg, pci_status[i]); 809 } 810 811 for (i = 0; i < 8; i++) { 812 u_int bit; 813 814 if (i == 5) 815 continue; 816 817 for (bit = 0; bit < 8; bit++) { 818 819 if ((pci_status[i] & (0x1 << bit)) != 0) { 820 const char *s; 821 822 s = pci_status_strings[bit]; 823 if (i == 7/*TARG*/ && bit == 3) 824 s = "%s: Signaled Target Abort\n"; 825 printk(s, ahd_name(ahd), pci_status_source[i]); 826 } 827 } 828 } 829 pci_status1 = ahd_pci_read_config(ahd->dev_softc, 830 PCIR_STATUS + 1, /*bytes*/1); 831 ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, 832 pci_status1, /*bytes*/1); 833 ahd_restore_modes(ahd, saved_modes); 834 ahd_outb(ahd, CLRINT, CLRPCIINT); 835 ahd_unpause(ahd); 836} 837 838static void 839ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat) 840{ 841 uint8_t split_status[4]; 842 uint8_t split_status1[4]; 843 uint8_t sg_split_status[2]; 844 uint8_t sg_split_status1[2]; 845 ahd_mode_state saved_modes; 846 u_int i; 847 uint16_t pcix_status; 848 849 /* 850 * Check for splits in all modes. Modes 0 and 1 851 * additionally have SG engine splits to look at. 852 */ 853 pcix_status = ahd_pci_read_config(ahd->dev_softc, PCIXR_STATUS, 854 /*bytes*/2); 855 printk("%s: PCI Split Interrupt - PCI-X status = 0x%x\n", 856 ahd_name(ahd), pcix_status); 857 saved_modes = ahd_save_modes(ahd); 858 for (i = 0; i < 4; i++) { 859 ahd_set_modes(ahd, i, i); 860 861 split_status[i] = ahd_inb(ahd, DCHSPLTSTAT0); 862 split_status1[i] = ahd_inb(ahd, DCHSPLTSTAT1); 863 /* Clear latched errors. So our interrupt deasserts. */ 864 ahd_outb(ahd, DCHSPLTSTAT0, split_status[i]); 865 ahd_outb(ahd, DCHSPLTSTAT1, split_status1[i]); 866 if (i > 1) 867 continue; 868 sg_split_status[i] = ahd_inb(ahd, SGSPLTSTAT0); 869 sg_split_status1[i] = ahd_inb(ahd, SGSPLTSTAT1); 870 /* Clear latched errors. So our interrupt deasserts. */ 871 ahd_outb(ahd, SGSPLTSTAT0, sg_split_status[i]); 872 ahd_outb(ahd, SGSPLTSTAT1, sg_split_status1[i]); 873 } 874 875 for (i = 0; i < 4; i++) { 876 u_int bit; 877 878 for (bit = 0; bit < 8; bit++) { 879 880 if ((split_status[i] & (0x1 << bit)) != 0) 881 printk(split_status_strings[bit], ahd_name(ahd), 882 split_status_source[i]); 883 884 if (i > 1) 885 continue; 886 887 if ((sg_split_status[i] & (0x1 << bit)) != 0) 888 printk(split_status_strings[bit], ahd_name(ahd), "SG"); 889 } 890 } 891 /* 892 * Clear PCI-X status bits. 893 */ 894 ahd_pci_write_config(ahd->dev_softc, PCIXR_STATUS, 895 pcix_status, /*bytes*/2); 896 ahd_outb(ahd, CLRINT, CLRSPLTINT); 897 ahd_restore_modes(ahd, saved_modes); 898} 899 900static int 901ahd_aic7901_setup(struct ahd_softc *ahd) 902{ 903 904 ahd->chip = AHD_AIC7901; 905 ahd->features = AHD_AIC7901_FE; 906 return (ahd_aic790X_setup(ahd)); 907} 908 909static int 910ahd_aic7901A_setup(struct ahd_softc *ahd) 911{ 912 913 ahd->chip = AHD_AIC7901A; 914 ahd->features = AHD_AIC7901A_FE; 915 return (ahd_aic790X_setup(ahd)); 916} 917 918static int 919ahd_aic7902_setup(struct ahd_softc *ahd) 920{ 921 ahd->chip = AHD_AIC7902; 922 ahd->features = AHD_AIC7902_FE; 923 return (ahd_aic790X_setup(ahd)); 924} 925 926static int 927ahd_aic790X_setup(struct ahd_softc *ahd) 928{ 929 ahd_dev_softc_t pci; 930 u_int rev; 931 932 pci = ahd->dev_softc; 933 rev = ahd_pci_read_config(pci, PCIR_REVID, /*bytes*/1); 934 if (rev < ID_AIC7902_PCI_REV_A4) { 935 printk("%s: Unable to attach to unsupported chip revision %d\n", 936 ahd_name(ahd), rev); 937 ahd_pci_write_config(pci, PCIR_COMMAND, 0, /*bytes*/2); 938 return (ENXIO); 939 } 940 ahd->channel = ahd_get_pci_function(pci) + 'A'; 941 if (rev < ID_AIC7902_PCI_REV_B0) { 942 /* 943 * Enable A series workarounds. 944 */ 945 ahd->bugs |= AHD_SENT_SCB_UPDATE_BUG|AHD_ABORT_LQI_BUG 946 | AHD_PKT_BITBUCKET_BUG|AHD_LONG_SETIMO_BUG 947 | AHD_NLQICRC_DELAYED_BUG|AHD_SCSIRST_BUG 948 | AHD_LQO_ATNO_BUG|AHD_AUTOFLUSH_BUG 949 | AHD_CLRLQO_AUTOCLR_BUG|AHD_PCIX_MMAPIO_BUG 950 | AHD_PCIX_CHIPRST_BUG|AHD_PCIX_SCBRAM_RD_BUG 951 | AHD_PKTIZED_STATUS_BUG|AHD_PKT_LUN_BUG 952 | AHD_MDFF_WSCBPTR_BUG|AHD_REG_SLOW_SETTLE_BUG 953 | AHD_SET_MODE_BUG|AHD_BUSFREEREV_BUG 954 | AHD_NONPACKFIFO_BUG|AHD_PACED_NEGTABLE_BUG 955 | AHD_FAINT_LED_BUG; 956 957 /* 958 * IO Cell parameter setup. 959 */ 960 AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29); 961 962 if ((ahd->flags & AHD_HP_BOARD) == 0) 963 AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVA); 964 } else { 965 /* This is revision B and newer. */ 966 extern uint32_t aic79xx_slowcrc; 967 u_int devconfig1; 968 969 ahd->features |= AHD_RTI|AHD_NEW_IOCELL_OPTS 970 | AHD_NEW_DFCNTRL_OPTS|AHD_FAST_CDB_DELIVERY 971 | AHD_BUSFREEREV_BUG; 972 ahd->bugs |= AHD_LQOOVERRUN_BUG|AHD_EARLY_REQ_BUG; 973 974 /* If the user requested that the SLOWCRC bit to be set. */ 975 if (aic79xx_slowcrc) 976 ahd->features |= AHD_AIC79XXB_SLOWCRC; 977 978 /* 979 * Some issues have been resolved in the 7901B. 980 */ 981 if ((ahd->features & AHD_MULTI_FUNC) != 0) 982 ahd->bugs |= AHD_INTCOLLISION_BUG|AHD_ABORT_LQI_BUG; 983 984 /* 985 * IO Cell parameter setup. 986 */ 987 AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29); 988 AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVB); 989 AHD_SET_AMPLITUDE(ahd, AHD_AMPLITUDE_DEF); 990 991 /* 992 * Set the PREQDIS bit for H2B which disables some workaround 993 * that doesn't work on regular PCI busses. 994 * XXX - Find out exactly what this does from the hardware 995 * folks! 996 */ 997 devconfig1 = ahd_pci_read_config(pci, DEVCONFIG1, /*bytes*/1); 998 ahd_pci_write_config(pci, DEVCONFIG1, 999 devconfig1|PREQDIS, /*bytes*/1); 1000 devconfig1 = ahd_pci_read_config(pci, DEVCONFIG1, /*bytes*/1); 1001 } 1002 1003 return (0); 1004} 1005