1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * Copyright (c) 2016, BayLibre, SAS. All rights reserved. 4 * Author: Neil Armstrong <narmstrong@baylibre.com> 5 * 6 * Copyright (c) 2010, Code Aurora Forum. All rights reserved. 7 * 8 * Driver for Semtech SX150X I2C GPIO Expanders 9 * The handling of the 4-bit chips (SX1501/SX1504/SX1507) is untested. 10 * 11 * Author: Gregory Bean <gbean@codeaurora.org> 12 */ 13 14#include <linux/regmap.h> 15#include <linux/i2c.h> 16#include <linux/init.h> 17#include <linux/interrupt.h> 18#include <linux/irq.h> 19#include <linux/mutex.h> 20#include <linux/slab.h> 21#include <linux/of.h> 22#include <linux/gpio/driver.h> 23#include <linux/pinctrl/pinconf.h> 24#include <linux/pinctrl/pinctrl.h> 25#include <linux/pinctrl/pinmux.h> 26#include <linux/pinctrl/pinconf-generic.h> 27 28#include "core.h" 29#include "pinconf.h" 30#include "pinctrl-utils.h" 31 32/* The chip models of sx150x */ 33enum { 34 SX150X_123 = 0, 35 SX150X_456, 36 SX150X_789, 37}; 38enum { 39 SX150X_789_REG_MISC_AUTOCLEAR_OFF = 1 << 0, 40 SX150X_MAX_REGISTER = 0xad, 41 SX150X_IRQ_TYPE_EDGE_RISING = 0x1, 42 SX150X_IRQ_TYPE_EDGE_FALLING = 0x2, 43 SX150X_789_RESET_KEY1 = 0x12, 44 SX150X_789_RESET_KEY2 = 0x34, 45}; 46 47struct sx150x_123_pri { 48 u8 reg_pld_mode; 49 u8 reg_pld_table0; 50 u8 reg_pld_table1; 51 u8 reg_pld_table2; 52 u8 reg_pld_table3; 53 u8 reg_pld_table4; 54 u8 reg_advanced; 55}; 56 57struct sx150x_456_pri { 58 u8 reg_pld_mode; 59 u8 reg_pld_table0; 60 u8 reg_pld_table1; 61 u8 reg_pld_table2; 62 u8 reg_pld_table3; 63 u8 reg_pld_table4; 64 u8 reg_advanced; 65}; 66 67struct sx150x_789_pri { 68 u8 reg_drain; 69 u8 reg_polarity; 70 u8 reg_clock; 71 u8 reg_misc; 72 u8 reg_reset; 73 u8 ngpios; 74}; 75 76struct sx150x_device_data { 77 u8 model; 78 u8 reg_pullup; 79 u8 reg_pulldn; 80 u8 reg_dir; 81 u8 reg_data; 82 u8 reg_irq_mask; 83 u8 reg_irq_src; 84 u8 reg_sense; 85 u8 ngpios; 86 union { 87 struct sx150x_123_pri x123; 88 struct sx150x_456_pri x456; 89 struct sx150x_789_pri x789; 90 } pri; 91 const struct pinctrl_pin_desc *pins; 92 unsigned int npins; 93}; 94 95struct sx150x_pinctrl { 96 struct device *dev; 97 struct i2c_client *client; 98 struct pinctrl_dev *pctldev; 99 struct pinctrl_desc pinctrl_desc; 100 struct gpio_chip gpio; 101 struct regmap *regmap; 102 struct { 103 u32 sense; 104 u32 masked; 105 } irq; 106 struct mutex lock; 107 const struct sx150x_device_data *data; 108}; 109 110static const struct pinctrl_pin_desc sx150x_4_pins[] = { 111 PINCTRL_PIN(0, "gpio0"), 112 PINCTRL_PIN(1, "gpio1"), 113 PINCTRL_PIN(2, "gpio2"), 114 PINCTRL_PIN(3, "gpio3"), 115 PINCTRL_PIN(4, "oscio"), 116}; 117 118static const struct pinctrl_pin_desc sx150x_8_pins[] = { 119 PINCTRL_PIN(0, "gpio0"), 120 PINCTRL_PIN(1, "gpio1"), 121 PINCTRL_PIN(2, "gpio2"), 122 PINCTRL_PIN(3, "gpio3"), 123 PINCTRL_PIN(4, "gpio4"), 124 PINCTRL_PIN(5, "gpio5"), 125 PINCTRL_PIN(6, "gpio6"), 126 PINCTRL_PIN(7, "gpio7"), 127 PINCTRL_PIN(8, "oscio"), 128}; 129 130static const struct pinctrl_pin_desc sx150x_16_pins[] = { 131 PINCTRL_PIN(0, "gpio0"), 132 PINCTRL_PIN(1, "gpio1"), 133 PINCTRL_PIN(2, "gpio2"), 134 PINCTRL_PIN(3, "gpio3"), 135 PINCTRL_PIN(4, "gpio4"), 136 PINCTRL_PIN(5, "gpio5"), 137 PINCTRL_PIN(6, "gpio6"), 138 PINCTRL_PIN(7, "gpio7"), 139 PINCTRL_PIN(8, "gpio8"), 140 PINCTRL_PIN(9, "gpio9"), 141 PINCTRL_PIN(10, "gpio10"), 142 PINCTRL_PIN(11, "gpio11"), 143 PINCTRL_PIN(12, "gpio12"), 144 PINCTRL_PIN(13, "gpio13"), 145 PINCTRL_PIN(14, "gpio14"), 146 PINCTRL_PIN(15, "gpio15"), 147 PINCTRL_PIN(16, "oscio"), 148}; 149 150static const struct sx150x_device_data sx1501q_device_data = { 151 .model = SX150X_123, 152 .reg_pullup = 0x02, 153 .reg_pulldn = 0x03, 154 .reg_dir = 0x01, 155 .reg_data = 0x00, 156 .reg_irq_mask = 0x05, 157 .reg_irq_src = 0x08, 158 .reg_sense = 0x07, 159 .pri.x123 = { 160 .reg_pld_mode = 0x10, 161 .reg_pld_table0 = 0x11, 162 .reg_pld_table2 = 0x13, 163 .reg_advanced = 0xad, 164 }, 165 .ngpios = 4, 166 .pins = sx150x_4_pins, 167 .npins = 4, /* oscio not available */ 168}; 169 170static const struct sx150x_device_data sx1502q_device_data = { 171 .model = SX150X_123, 172 .reg_pullup = 0x02, 173 .reg_pulldn = 0x03, 174 .reg_dir = 0x01, 175 .reg_data = 0x00, 176 .reg_irq_mask = 0x05, 177 .reg_irq_src = 0x08, 178 .reg_sense = 0x06, 179 .pri.x123 = { 180 .reg_pld_mode = 0x10, 181 .reg_pld_table0 = 0x11, 182 .reg_pld_table1 = 0x12, 183 .reg_pld_table2 = 0x13, 184 .reg_pld_table3 = 0x14, 185 .reg_pld_table4 = 0x15, 186 .reg_advanced = 0xad, 187 }, 188 .ngpios = 8, 189 .pins = sx150x_8_pins, 190 .npins = 8, /* oscio not available */ 191}; 192 193static const struct sx150x_device_data sx1503q_device_data = { 194 .model = SX150X_123, 195 .reg_pullup = 0x04, 196 .reg_pulldn = 0x06, 197 .reg_dir = 0x02, 198 .reg_data = 0x00, 199 .reg_irq_mask = 0x08, 200 .reg_irq_src = 0x0e, 201 .reg_sense = 0x0a, 202 .pri.x123 = { 203 .reg_pld_mode = 0x20, 204 .reg_pld_table0 = 0x22, 205 .reg_pld_table1 = 0x24, 206 .reg_pld_table2 = 0x26, 207 .reg_pld_table3 = 0x28, 208 .reg_pld_table4 = 0x2a, 209 .reg_advanced = 0xad, 210 }, 211 .ngpios = 16, 212 .pins = sx150x_16_pins, 213 .npins = 16, /* oscio not available */ 214}; 215 216static const struct sx150x_device_data sx1504q_device_data = { 217 .model = SX150X_456, 218 .reg_pullup = 0x02, 219 .reg_pulldn = 0x03, 220 .reg_dir = 0x01, 221 .reg_data = 0x00, 222 .reg_irq_mask = 0x05, 223 .reg_irq_src = 0x08, 224 .reg_sense = 0x07, 225 .pri.x456 = { 226 .reg_pld_mode = 0x10, 227 .reg_pld_table0 = 0x11, 228 .reg_pld_table2 = 0x13, 229 }, 230 .ngpios = 4, 231 .pins = sx150x_4_pins, 232 .npins = 4, /* oscio not available */ 233}; 234 235static const struct sx150x_device_data sx1505q_device_data = { 236 .model = SX150X_456, 237 .reg_pullup = 0x02, 238 .reg_pulldn = 0x03, 239 .reg_dir = 0x01, 240 .reg_data = 0x00, 241 .reg_irq_mask = 0x05, 242 .reg_irq_src = 0x08, 243 .reg_sense = 0x06, 244 .pri.x456 = { 245 .reg_pld_mode = 0x10, 246 .reg_pld_table0 = 0x11, 247 .reg_pld_table1 = 0x12, 248 .reg_pld_table2 = 0x13, 249 .reg_pld_table3 = 0x14, 250 .reg_pld_table4 = 0x15, 251 }, 252 .ngpios = 8, 253 .pins = sx150x_8_pins, 254 .npins = 8, /* oscio not available */ 255}; 256 257static const struct sx150x_device_data sx1506q_device_data = { 258 .model = SX150X_456, 259 .reg_pullup = 0x04, 260 .reg_pulldn = 0x06, 261 .reg_dir = 0x02, 262 .reg_data = 0x00, 263 .reg_irq_mask = 0x08, 264 .reg_irq_src = 0x0e, 265 .reg_sense = 0x0a, 266 .pri.x456 = { 267 .reg_pld_mode = 0x20, 268 .reg_pld_table0 = 0x22, 269 .reg_pld_table1 = 0x24, 270 .reg_pld_table2 = 0x26, 271 .reg_pld_table3 = 0x28, 272 .reg_pld_table4 = 0x2a, 273 .reg_advanced = 0xad, 274 }, 275 .ngpios = 16, 276 .pins = sx150x_16_pins, 277 .npins = 16, /* oscio not available */ 278}; 279 280static const struct sx150x_device_data sx1507q_device_data = { 281 .model = SX150X_789, 282 .reg_pullup = 0x03, 283 .reg_pulldn = 0x04, 284 .reg_dir = 0x07, 285 .reg_data = 0x08, 286 .reg_irq_mask = 0x09, 287 .reg_irq_src = 0x0b, 288 .reg_sense = 0x0a, 289 .pri.x789 = { 290 .reg_drain = 0x05, 291 .reg_polarity = 0x06, 292 .reg_clock = 0x0d, 293 .reg_misc = 0x0e, 294 .reg_reset = 0x7d, 295 }, 296 .ngpios = 4, 297 .pins = sx150x_4_pins, 298 .npins = ARRAY_SIZE(sx150x_4_pins), 299}; 300 301static const struct sx150x_device_data sx1508q_device_data = { 302 .model = SX150X_789, 303 .reg_pullup = 0x03, 304 .reg_pulldn = 0x04, 305 .reg_dir = 0x07, 306 .reg_data = 0x08, 307 .reg_irq_mask = 0x09, 308 .reg_irq_src = 0x0c, 309 .reg_sense = 0x0a, 310 .pri.x789 = { 311 .reg_drain = 0x05, 312 .reg_polarity = 0x06, 313 .reg_clock = 0x0f, 314 .reg_misc = 0x10, 315 .reg_reset = 0x7d, 316 }, 317 .ngpios = 8, 318 .pins = sx150x_8_pins, 319 .npins = ARRAY_SIZE(sx150x_8_pins), 320}; 321 322static const struct sx150x_device_data sx1509q_device_data = { 323 .model = SX150X_789, 324 .reg_pullup = 0x06, 325 .reg_pulldn = 0x08, 326 .reg_dir = 0x0e, 327 .reg_data = 0x10, 328 .reg_irq_mask = 0x12, 329 .reg_irq_src = 0x18, 330 .reg_sense = 0x14, 331 .pri.x789 = { 332 .reg_drain = 0x0a, 333 .reg_polarity = 0x0c, 334 .reg_clock = 0x1e, 335 .reg_misc = 0x1f, 336 .reg_reset = 0x7d, 337 }, 338 .ngpios = 16, 339 .pins = sx150x_16_pins, 340 .npins = ARRAY_SIZE(sx150x_16_pins), 341}; 342 343static int sx150x_pinctrl_get_groups_count(struct pinctrl_dev *pctldev) 344{ 345 return 0; 346} 347 348static const char *sx150x_pinctrl_get_group_name(struct pinctrl_dev *pctldev, 349 unsigned int group) 350{ 351 return NULL; 352} 353 354static int sx150x_pinctrl_get_group_pins(struct pinctrl_dev *pctldev, 355 unsigned int group, 356 const unsigned int **pins, 357 unsigned int *num_pins) 358{ 359 return -ENOTSUPP; 360} 361 362static const struct pinctrl_ops sx150x_pinctrl_ops = { 363 .get_groups_count = sx150x_pinctrl_get_groups_count, 364 .get_group_name = sx150x_pinctrl_get_group_name, 365 .get_group_pins = sx150x_pinctrl_get_group_pins, 366#ifdef CONFIG_OF 367 .dt_node_to_map = pinconf_generic_dt_node_to_map_pin, 368 .dt_free_map = pinctrl_utils_free_map, 369#endif 370}; 371 372static bool sx150x_pin_is_oscio(struct sx150x_pinctrl *pctl, unsigned int pin) 373{ 374 if (pin >= pctl->data->npins) 375 return false; 376 377 /* OSCIO pin is only present in 789 devices */ 378 if (pctl->data->model != SX150X_789) 379 return false; 380 381 return !strcmp(pctl->data->pins[pin].name, "oscio"); 382} 383 384static int sx150x_gpio_get_direction(struct gpio_chip *chip, 385 unsigned int offset) 386{ 387 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 388 unsigned int value; 389 int ret; 390 391 if (sx150x_pin_is_oscio(pctl, offset)) 392 return GPIO_LINE_DIRECTION_OUT; 393 394 ret = regmap_read(pctl->regmap, pctl->data->reg_dir, &value); 395 if (ret < 0) 396 return ret; 397 398 if (value & BIT(offset)) 399 return GPIO_LINE_DIRECTION_IN; 400 401 return GPIO_LINE_DIRECTION_OUT; 402} 403 404static int sx150x_gpio_get(struct gpio_chip *chip, unsigned int offset) 405{ 406 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 407 unsigned int value; 408 int ret; 409 410 if (sx150x_pin_is_oscio(pctl, offset)) 411 return -EINVAL; 412 413 ret = regmap_read(pctl->regmap, pctl->data->reg_data, &value); 414 if (ret < 0) 415 return ret; 416 417 return !!(value & BIT(offset)); 418} 419 420static int __sx150x_gpio_set(struct sx150x_pinctrl *pctl, unsigned int offset, 421 int value) 422{ 423 return regmap_write_bits(pctl->regmap, pctl->data->reg_data, 424 BIT(offset), value ? BIT(offset) : 0); 425} 426 427static int sx150x_gpio_oscio_set(struct sx150x_pinctrl *pctl, 428 int value) 429{ 430 return regmap_write(pctl->regmap, 431 pctl->data->pri.x789.reg_clock, 432 (value ? 0x1f : 0x10)); 433} 434 435static void sx150x_gpio_set(struct gpio_chip *chip, unsigned int offset, 436 int value) 437{ 438 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 439 440 if (sx150x_pin_is_oscio(pctl, offset)) 441 sx150x_gpio_oscio_set(pctl, value); 442 else 443 __sx150x_gpio_set(pctl, offset, value); 444} 445 446static void sx150x_gpio_set_multiple(struct gpio_chip *chip, 447 unsigned long *mask, 448 unsigned long *bits) 449{ 450 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 451 452 regmap_write_bits(pctl->regmap, pctl->data->reg_data, *mask, *bits); 453} 454 455static int sx150x_gpio_direction_input(struct gpio_chip *chip, 456 unsigned int offset) 457{ 458 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 459 460 if (sx150x_pin_is_oscio(pctl, offset)) 461 return -EINVAL; 462 463 return regmap_write_bits(pctl->regmap, 464 pctl->data->reg_dir, 465 BIT(offset), BIT(offset)); 466} 467 468static int sx150x_gpio_direction_output(struct gpio_chip *chip, 469 unsigned int offset, int value) 470{ 471 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 472 int ret; 473 474 if (sx150x_pin_is_oscio(pctl, offset)) 475 return sx150x_gpio_oscio_set(pctl, value); 476 477 ret = __sx150x_gpio_set(pctl, offset, value); 478 if (ret < 0) 479 return ret; 480 481 return regmap_write_bits(pctl->regmap, 482 pctl->data->reg_dir, 483 BIT(offset), 0); 484} 485 486static void sx150x_irq_mask(struct irq_data *d) 487{ 488 struct gpio_chip *gc = irq_data_get_irq_chip_data(d); 489 struct sx150x_pinctrl *pctl = gpiochip_get_data(gc); 490 unsigned int n = irqd_to_hwirq(d); 491 492 pctl->irq.masked |= BIT(n); 493 gpiochip_disable_irq(gc, n); 494} 495 496static void sx150x_irq_unmask(struct irq_data *d) 497{ 498 struct gpio_chip *gc = irq_data_get_irq_chip_data(d); 499 struct sx150x_pinctrl *pctl = gpiochip_get_data(gc); 500 unsigned int n = irqd_to_hwirq(d); 501 502 gpiochip_enable_irq(gc, n); 503 pctl->irq.masked &= ~BIT(n); 504} 505 506static void sx150x_irq_set_sense(struct sx150x_pinctrl *pctl, 507 unsigned int line, unsigned int sense) 508{ 509 /* 510 * Every interrupt line is represented by two bits shifted 511 * proportionally to the line number 512 */ 513 const unsigned int n = line * 2; 514 const unsigned int mask = ~((SX150X_IRQ_TYPE_EDGE_RISING | 515 SX150X_IRQ_TYPE_EDGE_FALLING) << n); 516 517 pctl->irq.sense &= mask; 518 pctl->irq.sense |= sense << n; 519} 520 521static int sx150x_irq_set_type(struct irq_data *d, unsigned int flow_type) 522{ 523 struct gpio_chip *gc = irq_data_get_irq_chip_data(d); 524 struct sx150x_pinctrl *pctl = gpiochip_get_data(gc); 525 unsigned int n, val = 0; 526 527 if (flow_type & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) 528 return -EINVAL; 529 530 n = irqd_to_hwirq(d); 531 532 if (flow_type & IRQ_TYPE_EDGE_RISING) 533 val |= SX150X_IRQ_TYPE_EDGE_RISING; 534 if (flow_type & IRQ_TYPE_EDGE_FALLING) 535 val |= SX150X_IRQ_TYPE_EDGE_FALLING; 536 537 sx150x_irq_set_sense(pctl, n, val); 538 return 0; 539} 540 541static irqreturn_t sx150x_irq_thread_fn(int irq, void *dev_id) 542{ 543 struct sx150x_pinctrl *pctl = (struct sx150x_pinctrl *)dev_id; 544 unsigned long n, status; 545 unsigned int val; 546 int err; 547 548 err = regmap_read(pctl->regmap, pctl->data->reg_irq_src, &val); 549 if (err < 0) 550 return IRQ_NONE; 551 552 err = regmap_write(pctl->regmap, pctl->data->reg_irq_src, val); 553 if (err < 0) 554 return IRQ_NONE; 555 556 status = val; 557 for_each_set_bit(n, &status, pctl->data->ngpios) 558 handle_nested_irq(irq_find_mapping(pctl->gpio.irq.domain, n)); 559 560 return IRQ_HANDLED; 561} 562 563static void sx150x_irq_bus_lock(struct irq_data *d) 564{ 565 struct gpio_chip *gc = irq_data_get_irq_chip_data(d); 566 struct sx150x_pinctrl *pctl = gpiochip_get_data(gc); 567 568 mutex_lock(&pctl->lock); 569} 570 571static void sx150x_irq_bus_sync_unlock(struct irq_data *d) 572{ 573 struct gpio_chip *gc = irq_data_get_irq_chip_data(d); 574 struct sx150x_pinctrl *pctl = gpiochip_get_data(gc); 575 576 regmap_write(pctl->regmap, pctl->data->reg_irq_mask, pctl->irq.masked); 577 regmap_write(pctl->regmap, pctl->data->reg_sense, pctl->irq.sense); 578 mutex_unlock(&pctl->lock); 579} 580 581 582static void sx150x_irq_print_chip(struct irq_data *d, struct seq_file *p) 583{ 584 struct gpio_chip *gc = irq_data_get_irq_chip_data(d); 585 struct sx150x_pinctrl *pctl = gpiochip_get_data(gc); 586 587 seq_printf(p, pctl->client->name); 588} 589 590static const struct irq_chip sx150x_irq_chip = { 591 .irq_mask = sx150x_irq_mask, 592 .irq_unmask = sx150x_irq_unmask, 593 .irq_set_type = sx150x_irq_set_type, 594 .irq_bus_lock = sx150x_irq_bus_lock, 595 .irq_bus_sync_unlock = sx150x_irq_bus_sync_unlock, 596 .irq_print_chip = sx150x_irq_print_chip, 597 .flags = IRQCHIP_IMMUTABLE, 598 GPIOCHIP_IRQ_RESOURCE_HELPERS, 599}; 600 601static int sx150x_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, 602 unsigned long *config) 603{ 604 struct sx150x_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev); 605 unsigned int param = pinconf_to_config_param(*config); 606 int ret; 607 u32 arg; 608 unsigned int data; 609 610 if (sx150x_pin_is_oscio(pctl, pin)) { 611 switch (param) { 612 case PIN_CONFIG_DRIVE_PUSH_PULL: 613 case PIN_CONFIG_OUTPUT: 614 ret = regmap_read(pctl->regmap, 615 pctl->data->pri.x789.reg_clock, 616 &data); 617 if (ret < 0) 618 return ret; 619 620 if (param == PIN_CONFIG_DRIVE_PUSH_PULL) 621 arg = (data & 0x1f) ? 1 : 0; 622 else { 623 if ((data & 0x1f) == 0x1f) 624 arg = 1; 625 else if ((data & 0x1f) == 0x10) 626 arg = 0; 627 else 628 return -EINVAL; 629 } 630 631 break; 632 default: 633 return -ENOTSUPP; 634 } 635 636 goto out; 637 } 638 639 switch (param) { 640 case PIN_CONFIG_BIAS_PULL_DOWN: 641 ret = regmap_read(pctl->regmap, 642 pctl->data->reg_pulldn, 643 &data); 644 data &= BIT(pin); 645 646 if (ret < 0) 647 return ret; 648 649 if (!ret) 650 return -EINVAL; 651 652 arg = 1; 653 break; 654 655 case PIN_CONFIG_BIAS_PULL_UP: 656 ret = regmap_read(pctl->regmap, 657 pctl->data->reg_pullup, 658 &data); 659 data &= BIT(pin); 660 661 if (ret < 0) 662 return ret; 663 664 if (!ret) 665 return -EINVAL; 666 667 arg = 1; 668 break; 669 670 case PIN_CONFIG_DRIVE_OPEN_DRAIN: 671 if (pctl->data->model != SX150X_789) 672 return -ENOTSUPP; 673 674 ret = regmap_read(pctl->regmap, 675 pctl->data->pri.x789.reg_drain, 676 &data); 677 data &= BIT(pin); 678 679 if (ret < 0) 680 return ret; 681 682 if (!data) 683 return -EINVAL; 684 685 arg = 1; 686 break; 687 688 case PIN_CONFIG_DRIVE_PUSH_PULL: 689 if (pctl->data->model != SX150X_789) 690 arg = true; 691 else { 692 ret = regmap_read(pctl->regmap, 693 pctl->data->pri.x789.reg_drain, 694 &data); 695 data &= BIT(pin); 696 697 if (ret < 0) 698 return ret; 699 700 if (data) 701 return -EINVAL; 702 703 arg = 1; 704 } 705 break; 706 707 case PIN_CONFIG_OUTPUT: 708 ret = sx150x_gpio_get_direction(&pctl->gpio, pin); 709 if (ret < 0) 710 return ret; 711 712 if (ret == GPIO_LINE_DIRECTION_IN) 713 return -EINVAL; 714 715 ret = sx150x_gpio_get(&pctl->gpio, pin); 716 if (ret < 0) 717 return ret; 718 719 arg = ret; 720 break; 721 722 default: 723 return -ENOTSUPP; 724 } 725 726out: 727 *config = pinconf_to_config_packed(param, arg); 728 729 return 0; 730} 731 732static int sx150x_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin, 733 unsigned long *configs, unsigned int num_configs) 734{ 735 struct sx150x_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev); 736 enum pin_config_param param; 737 u32 arg; 738 int i; 739 int ret; 740 741 for (i = 0; i < num_configs; i++) { 742 param = pinconf_to_config_param(configs[i]); 743 arg = pinconf_to_config_argument(configs[i]); 744 745 if (sx150x_pin_is_oscio(pctl, pin)) { 746 if (param == PIN_CONFIG_OUTPUT) { 747 ret = sx150x_gpio_direction_output(&pctl->gpio, 748 pin, arg); 749 if (ret < 0) 750 return ret; 751 752 continue; 753 } else 754 return -ENOTSUPP; 755 } 756 757 switch (param) { 758 case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: 759 case PIN_CONFIG_BIAS_DISABLE: 760 ret = regmap_write_bits(pctl->regmap, 761 pctl->data->reg_pulldn, 762 BIT(pin), 0); 763 if (ret < 0) 764 return ret; 765 766 ret = regmap_write_bits(pctl->regmap, 767 pctl->data->reg_pullup, 768 BIT(pin), 0); 769 if (ret < 0) 770 return ret; 771 772 break; 773 774 case PIN_CONFIG_BIAS_PULL_UP: 775 ret = regmap_write_bits(pctl->regmap, 776 pctl->data->reg_pullup, 777 BIT(pin), BIT(pin)); 778 if (ret < 0) 779 return ret; 780 781 break; 782 783 case PIN_CONFIG_BIAS_PULL_DOWN: 784 ret = regmap_write_bits(pctl->regmap, 785 pctl->data->reg_pulldn, 786 BIT(pin), BIT(pin)); 787 if (ret < 0) 788 return ret; 789 790 break; 791 792 case PIN_CONFIG_DRIVE_OPEN_DRAIN: 793 if (pctl->data->model != SX150X_789 || 794 sx150x_pin_is_oscio(pctl, pin)) 795 return -ENOTSUPP; 796 797 ret = regmap_write_bits(pctl->regmap, 798 pctl->data->pri.x789.reg_drain, 799 BIT(pin), BIT(pin)); 800 if (ret < 0) 801 return ret; 802 803 break; 804 805 case PIN_CONFIG_DRIVE_PUSH_PULL: 806 if (pctl->data->model != SX150X_789 || 807 sx150x_pin_is_oscio(pctl, pin)) 808 return 0; 809 810 ret = regmap_write_bits(pctl->regmap, 811 pctl->data->pri.x789.reg_drain, 812 BIT(pin), 0); 813 if (ret < 0) 814 return ret; 815 816 break; 817 818 case PIN_CONFIG_OUTPUT: 819 ret = sx150x_gpio_direction_output(&pctl->gpio, 820 pin, arg); 821 if (ret < 0) 822 return ret; 823 824 break; 825 826 default: 827 return -ENOTSUPP; 828 } 829 } /* for each config */ 830 831 return 0; 832} 833 834static const struct pinconf_ops sx150x_pinconf_ops = { 835 .pin_config_get = sx150x_pinconf_get, 836 .pin_config_set = sx150x_pinconf_set, 837 .is_generic = true, 838}; 839 840static const struct i2c_device_id sx150x_id[] = { 841 {"sx1501q", (kernel_ulong_t) &sx1501q_device_data }, 842 {"sx1502q", (kernel_ulong_t) &sx1502q_device_data }, 843 {"sx1503q", (kernel_ulong_t) &sx1503q_device_data }, 844 {"sx1504q", (kernel_ulong_t) &sx1504q_device_data }, 845 {"sx1505q", (kernel_ulong_t) &sx1505q_device_data }, 846 {"sx1506q", (kernel_ulong_t) &sx1506q_device_data }, 847 {"sx1507q", (kernel_ulong_t) &sx1507q_device_data }, 848 {"sx1508q", (kernel_ulong_t) &sx1508q_device_data }, 849 {"sx1509q", (kernel_ulong_t) &sx1509q_device_data }, 850 {} 851}; 852 853static const struct of_device_id sx150x_of_match[] = { 854 { .compatible = "semtech,sx1501q", .data = &sx1501q_device_data }, 855 { .compatible = "semtech,sx1502q", .data = &sx1502q_device_data }, 856 { .compatible = "semtech,sx1503q", .data = &sx1503q_device_data }, 857 { .compatible = "semtech,sx1504q", .data = &sx1504q_device_data }, 858 { .compatible = "semtech,sx1505q", .data = &sx1505q_device_data }, 859 { .compatible = "semtech,sx1506q", .data = &sx1506q_device_data }, 860 { .compatible = "semtech,sx1507q", .data = &sx1507q_device_data }, 861 { .compatible = "semtech,sx1508q", .data = &sx1508q_device_data }, 862 { .compatible = "semtech,sx1509q", .data = &sx1509q_device_data }, 863 {}, 864}; 865 866static int sx150x_reset(struct sx150x_pinctrl *pctl) 867{ 868 int err; 869 870 err = i2c_smbus_write_byte_data(pctl->client, 871 pctl->data->pri.x789.reg_reset, 872 SX150X_789_RESET_KEY1); 873 if (err < 0) 874 return err; 875 876 err = i2c_smbus_write_byte_data(pctl->client, 877 pctl->data->pri.x789.reg_reset, 878 SX150X_789_RESET_KEY2); 879 return err; 880} 881 882static int sx150x_init_misc(struct sx150x_pinctrl *pctl) 883{ 884 u8 reg, value; 885 886 switch (pctl->data->model) { 887 case SX150X_789: 888 reg = pctl->data->pri.x789.reg_misc; 889 value = SX150X_789_REG_MISC_AUTOCLEAR_OFF; 890 break; 891 case SX150X_456: 892 reg = pctl->data->pri.x456.reg_advanced; 893 value = 0x00; 894 895 /* 896 * Only SX1506 has RegAdvanced, SX1504/5 are expected 897 * to initialize this offset to zero 898 */ 899 if (!reg) 900 return 0; 901 break; 902 case SX150X_123: 903 reg = pctl->data->pri.x123.reg_advanced; 904 value = 0x00; 905 break; 906 default: 907 WARN(1, "Unknown chip model %d\n", pctl->data->model); 908 return -EINVAL; 909 } 910 911 return regmap_write(pctl->regmap, reg, value); 912} 913 914static int sx150x_init_hw(struct sx150x_pinctrl *pctl) 915{ 916 const u8 reg[] = { 917 [SX150X_789] = pctl->data->pri.x789.reg_polarity, 918 [SX150X_456] = pctl->data->pri.x456.reg_pld_mode, 919 [SX150X_123] = pctl->data->pri.x123.reg_pld_mode, 920 }; 921 int err; 922 923 if (pctl->data->model == SX150X_789 && 924 of_property_read_bool(pctl->dev->of_node, "semtech,probe-reset")) { 925 err = sx150x_reset(pctl); 926 if (err < 0) 927 return err; 928 } 929 930 err = sx150x_init_misc(pctl); 931 if (err < 0) 932 return err; 933 934 /* Set all pins to work in normal mode */ 935 return regmap_write(pctl->regmap, reg[pctl->data->model], 0); 936} 937 938static int sx150x_regmap_reg_width(struct sx150x_pinctrl *pctl, 939 unsigned int reg) 940{ 941 const struct sx150x_device_data *data = pctl->data; 942 943 if (reg == data->reg_sense) { 944 /* 945 * RegSense packs two bits of configuration per GPIO, 946 * so we'd need to read twice as many bits as there 947 * are GPIO in our chip 948 */ 949 return 2 * data->ngpios; 950 } else if ((data->model == SX150X_789 && 951 (reg == data->pri.x789.reg_misc || 952 reg == data->pri.x789.reg_clock || 953 reg == data->pri.x789.reg_reset)) 954 || 955 (data->model == SX150X_123 && 956 reg == data->pri.x123.reg_advanced) 957 || 958 (data->model == SX150X_456 && 959 data->pri.x456.reg_advanced && 960 reg == data->pri.x456.reg_advanced)) { 961 return 8; 962 } else { 963 return data->ngpios; 964 } 965} 966 967static unsigned int sx150x_maybe_swizzle(struct sx150x_pinctrl *pctl, 968 unsigned int reg, unsigned int val) 969{ 970 unsigned int a, b; 971 const struct sx150x_device_data *data = pctl->data; 972 973 /* 974 * Whereas SX1509 presents RegSense in a simple layout as such: 975 * reg [ f f e e d d c c ] 976 * reg + 1 [ b b a a 9 9 8 8 ] 977 * reg + 2 [ 7 7 6 6 5 5 4 4 ] 978 * reg + 3 [ 3 3 2 2 1 1 0 0 ] 979 * 980 * SX1503 and SX1506 deviate from that data layout, instead storing 981 * their contents as follows: 982 * 983 * reg [ f f e e d d c c ] 984 * reg + 1 [ 7 7 6 6 5 5 4 4 ] 985 * reg + 2 [ b b a a 9 9 8 8 ] 986 * reg + 3 [ 3 3 2 2 1 1 0 0 ] 987 * 988 * so, taking that into account, we swap two 989 * inner bytes of a 4-byte result 990 */ 991 992 if (reg == data->reg_sense && 993 data->ngpios == 16 && 994 (data->model == SX150X_123 || 995 data->model == SX150X_456)) { 996 a = val & 0x00ff0000; 997 b = val & 0x0000ff00; 998 999 val &= 0xff0000ff; 1000 val |= b << 8; 1001 val |= a >> 8; 1002 } 1003 1004 return val; 1005} 1006 1007/* 1008 * In order to mask the differences between 16 and 8 bit expander 1009 * devices we set up a sligthly ficticious regmap that pretends to be 1010 * a set of 32-bit (to accommodate RegSenseLow/RegSenseHigh 1011 * pair/quartet) registers and transparently reconstructs those 1012 * registers via multiple I2C/SMBus reads 1013 * 1014 * This way the rest of the driver code, interfacing with the chip via 1015 * regmap API, can work assuming that each GPIO pin is represented by 1016 * a group of bits at an offset proportional to GPIO number within a 1017 * given register. 1018 */ 1019static int sx150x_regmap_reg_read(void *context, unsigned int reg, 1020 unsigned int *result) 1021{ 1022 int ret, n; 1023 struct sx150x_pinctrl *pctl = context; 1024 struct i2c_client *i2c = pctl->client; 1025 const int width = sx150x_regmap_reg_width(pctl, reg); 1026 unsigned int idx, val; 1027 1028 /* 1029 * There are four potential cases covered by this function: 1030 * 1031 * 1) 8-pin chip, single configuration bit register 1032 * 1033 * This is trivial the code below just needs to read: 1034 * reg [ 7 6 5 4 3 2 1 0 ] 1035 * 1036 * 2) 8-pin chip, double configuration bit register (RegSense) 1037 * 1038 * The read will be done as follows: 1039 * reg [ 7 7 6 6 5 5 4 4 ] 1040 * reg + 1 [ 3 3 2 2 1 1 0 0 ] 1041 * 1042 * 3) 16-pin chip, single configuration bit register 1043 * 1044 * The read will be done as follows: 1045 * reg [ f e d c b a 9 8 ] 1046 * reg + 1 [ 7 6 5 4 3 2 1 0 ] 1047 * 1048 * 4) 16-pin chip, double configuration bit register (RegSense) 1049 * 1050 * The read will be done as follows: 1051 * reg [ f f e e d d c c ] 1052 * reg + 1 [ b b a a 9 9 8 8 ] 1053 * reg + 2 [ 7 7 6 6 5 5 4 4 ] 1054 * reg + 3 [ 3 3 2 2 1 1 0 0 ] 1055 */ 1056 1057 for (n = width, val = 0, idx = reg; n > 0; n -= 8, idx++) { 1058 val <<= 8; 1059 1060 ret = i2c_smbus_read_byte_data(i2c, idx); 1061 if (ret < 0) 1062 return ret; 1063 1064 val |= ret; 1065 } 1066 1067 *result = sx150x_maybe_swizzle(pctl, reg, val); 1068 1069 return 0; 1070} 1071 1072static int sx150x_regmap_reg_write(void *context, unsigned int reg, 1073 unsigned int val) 1074{ 1075 int ret, n; 1076 struct sx150x_pinctrl *pctl = context; 1077 struct i2c_client *i2c = pctl->client; 1078 const int width = sx150x_regmap_reg_width(pctl, reg); 1079 1080 val = sx150x_maybe_swizzle(pctl, reg, val); 1081 1082 n = (width - 1) & ~7; 1083 do { 1084 const u8 byte = (val >> n) & 0xff; 1085 1086 ret = i2c_smbus_write_byte_data(i2c, reg, byte); 1087 if (ret < 0) 1088 return ret; 1089 1090 reg++; 1091 n -= 8; 1092 } while (n >= 0); 1093 1094 return 0; 1095} 1096 1097static bool sx150x_reg_volatile(struct device *dev, unsigned int reg) 1098{ 1099 struct sx150x_pinctrl *pctl = i2c_get_clientdata(to_i2c_client(dev)); 1100 1101 return reg == pctl->data->reg_irq_src || reg == pctl->data->reg_data; 1102} 1103 1104static const struct regmap_config sx150x_regmap_config = { 1105 .reg_bits = 8, 1106 .val_bits = 32, 1107 1108 .cache_type = REGCACHE_RBTREE, 1109 1110 .reg_read = sx150x_regmap_reg_read, 1111 .reg_write = sx150x_regmap_reg_write, 1112 1113 .max_register = SX150X_MAX_REGISTER, 1114 .volatile_reg = sx150x_reg_volatile, 1115}; 1116 1117static int sx150x_probe(struct i2c_client *client) 1118{ 1119 static const u32 i2c_funcs = I2C_FUNC_SMBUS_BYTE_DATA | 1120 I2C_FUNC_SMBUS_WRITE_WORD_DATA; 1121 struct device *dev = &client->dev; 1122 struct sx150x_pinctrl *pctl; 1123 int ret; 1124 1125 if (!i2c_check_functionality(client->adapter, i2c_funcs)) 1126 return -ENOSYS; 1127 1128 pctl = devm_kzalloc(dev, sizeof(*pctl), GFP_KERNEL); 1129 if (!pctl) 1130 return -ENOMEM; 1131 1132 i2c_set_clientdata(client, pctl); 1133 1134 pctl->dev = dev; 1135 pctl->client = client; 1136 1137 pctl->data = i2c_get_match_data(client); 1138 if (!pctl->data) 1139 return -EINVAL; 1140 1141 pctl->regmap = devm_regmap_init(dev, NULL, pctl, 1142 &sx150x_regmap_config); 1143 if (IS_ERR(pctl->regmap)) { 1144 ret = PTR_ERR(pctl->regmap); 1145 dev_err(dev, "Failed to allocate register map: %d\n", 1146 ret); 1147 return ret; 1148 } 1149 1150 mutex_init(&pctl->lock); 1151 1152 ret = sx150x_init_hw(pctl); 1153 if (ret) 1154 return ret; 1155 1156 /* Pinctrl_desc */ 1157 pctl->pinctrl_desc.name = "sx150x-pinctrl"; 1158 pctl->pinctrl_desc.pctlops = &sx150x_pinctrl_ops; 1159 pctl->pinctrl_desc.confops = &sx150x_pinconf_ops; 1160 pctl->pinctrl_desc.pins = pctl->data->pins; 1161 pctl->pinctrl_desc.npins = pctl->data->npins; 1162 pctl->pinctrl_desc.owner = THIS_MODULE; 1163 1164 ret = devm_pinctrl_register_and_init(dev, &pctl->pinctrl_desc, 1165 pctl, &pctl->pctldev); 1166 if (ret) { 1167 dev_err(dev, "Failed to register pinctrl device\n"); 1168 return ret; 1169 } 1170 1171 /* Register GPIO controller */ 1172 pctl->gpio.base = -1; 1173 pctl->gpio.ngpio = pctl->data->npins; 1174 pctl->gpio.get_direction = sx150x_gpio_get_direction; 1175 pctl->gpio.direction_input = sx150x_gpio_direction_input; 1176 pctl->gpio.direction_output = sx150x_gpio_direction_output; 1177 pctl->gpio.get = sx150x_gpio_get; 1178 pctl->gpio.set = sx150x_gpio_set; 1179 pctl->gpio.set_config = gpiochip_generic_config; 1180 pctl->gpio.parent = dev; 1181 pctl->gpio.can_sleep = true; 1182 pctl->gpio.label = devm_kstrdup(dev, client->name, GFP_KERNEL); 1183 if (!pctl->gpio.label) 1184 return -ENOMEM; 1185 1186 /* 1187 * Setting multiple pins is not safe when all pins are not 1188 * handled by the same regmap register. The oscio pin (present 1189 * on the SX150X_789 chips) lives in its own register, so 1190 * would require locking that is not in place at this time. 1191 */ 1192 if (pctl->data->model != SX150X_789) 1193 pctl->gpio.set_multiple = sx150x_gpio_set_multiple; 1194 1195 /* Add Interrupt support if an irq is specified */ 1196 if (client->irq > 0) { 1197 struct gpio_irq_chip *girq; 1198 1199 pctl->irq.masked = ~0; 1200 pctl->irq.sense = 0; 1201 /* 1202 * Because sx150x_irq_threaded_fn invokes all of the 1203 * nested interrupt handlers via handle_nested_irq, 1204 * any "handler" assigned to struct gpio_irq_chip 1205 * below is going to be ignored, so the choice of the 1206 * function does not matter that much. 1207 * 1208 * We set it to handle_bad_irq to avoid confusion, 1209 * plus it will be instantly noticeable if it is ever 1210 * called (should not happen) 1211 */ 1212 girq = &pctl->gpio.irq; 1213 gpio_irq_chip_set_chip(girq, &sx150x_irq_chip); 1214 /* This will let us handle the parent IRQ in the driver */ 1215 girq->parent_handler = NULL; 1216 girq->num_parents = 0; 1217 girq->parents = NULL; 1218 girq->default_type = IRQ_TYPE_NONE; 1219 girq->handler = handle_bad_irq; 1220 girq->threaded = true; 1221 1222 ret = devm_request_threaded_irq(dev, client->irq, NULL, 1223 sx150x_irq_thread_fn, 1224 IRQF_ONESHOT | IRQF_SHARED | 1225 IRQF_TRIGGER_FALLING, 1226 client->name, pctl); 1227 if (ret < 0) 1228 return ret; 1229 } 1230 1231 ret = devm_gpiochip_add_data(dev, &pctl->gpio, pctl); 1232 if (ret) 1233 return ret; 1234 1235 /* 1236 * Pin control functions need to be enabled AFTER registering the 1237 * GPIO chip because sx150x_pinconf_set() calls 1238 * sx150x_gpio_direction_output(). 1239 */ 1240 ret = pinctrl_enable(pctl->pctldev); 1241 if (ret) { 1242 dev_err(dev, "Failed to enable pinctrl device\n"); 1243 return ret; 1244 } 1245 1246 ret = gpiochip_add_pin_range(&pctl->gpio, dev_name(dev), 1247 0, 0, pctl->data->npins); 1248 if (ret) 1249 return ret; 1250 1251 return 0; 1252} 1253 1254static struct i2c_driver sx150x_driver = { 1255 .driver = { 1256 .name = "sx150x-pinctrl", 1257 .of_match_table = sx150x_of_match, 1258 }, 1259 .probe = sx150x_probe, 1260 .id_table = sx150x_id, 1261}; 1262 1263static int __init sx150x_init(void) 1264{ 1265 return i2c_add_driver(&sx150x_driver); 1266} 1267subsys_initcall(sx150x_init); 1268