1// SPDX-License-Identifier: GPL-2.0 2/* Driver for the Texas Instruments DP83822, DP83825 and DP83826 PHYs. 3 * 4 * Copyright (C) 2017 Texas Instruments Inc. 5 */ 6 7#include <linux/ethtool.h> 8#include <linux/etherdevice.h> 9#include <linux/kernel.h> 10#include <linux/mii.h> 11#include <linux/module.h> 12#include <linux/of.h> 13#include <linux/phy.h> 14#include <linux/netdevice.h> 15#include <linux/bitfield.h> 16 17#define DP83822_PHY_ID 0x2000a240 18#define DP83825S_PHY_ID 0x2000a140 19#define DP83825I_PHY_ID 0x2000a150 20#define DP83825CM_PHY_ID 0x2000a160 21#define DP83825CS_PHY_ID 0x2000a170 22#define DP83826C_PHY_ID 0x2000a130 23#define DP83826NC_PHY_ID 0x2000a110 24 25#define DP83822_DEVADDR 0x1f 26 27#define MII_DP83822_CTRL_2 0x0a 28#define MII_DP83822_PHYSTS 0x10 29#define MII_DP83822_PHYSCR 0x11 30#define MII_DP83822_MISR1 0x12 31#define MII_DP83822_MISR2 0x13 32#define MII_DP83822_FCSCR 0x14 33#define MII_DP83822_RCSR 0x17 34#define MII_DP83822_RESET_CTRL 0x1f 35#define MII_DP83822_GENCFG 0x465 36#define MII_DP83822_SOR1 0x467 37 38/* DP83826 specific registers */ 39#define MII_DP83826_VOD_CFG1 0x30b 40#define MII_DP83826_VOD_CFG2 0x30c 41 42/* GENCFG */ 43#define DP83822_SIG_DET_LOW BIT(0) 44 45/* Control Register 2 bits */ 46#define DP83822_FX_ENABLE BIT(14) 47 48#define DP83822_HW_RESET BIT(15) 49#define DP83822_SW_RESET BIT(14) 50 51/* PHY STS bits */ 52#define DP83822_PHYSTS_DUPLEX BIT(2) 53#define DP83822_PHYSTS_10 BIT(1) 54#define DP83822_PHYSTS_LINK BIT(0) 55 56/* PHYSCR Register Fields */ 57#define DP83822_PHYSCR_INT_OE BIT(0) /* Interrupt Output Enable */ 58#define DP83822_PHYSCR_INTEN BIT(1) /* Interrupt Enable */ 59 60/* MISR1 bits */ 61#define DP83822_RX_ERR_HF_INT_EN BIT(0) 62#define DP83822_FALSE_CARRIER_HF_INT_EN BIT(1) 63#define DP83822_ANEG_COMPLETE_INT_EN BIT(2) 64#define DP83822_DUP_MODE_CHANGE_INT_EN BIT(3) 65#define DP83822_SPEED_CHANGED_INT_EN BIT(4) 66#define DP83822_LINK_STAT_INT_EN BIT(5) 67#define DP83822_ENERGY_DET_INT_EN BIT(6) 68#define DP83822_LINK_QUAL_INT_EN BIT(7) 69 70/* MISR2 bits */ 71#define DP83822_JABBER_DET_INT_EN BIT(0) 72#define DP83822_WOL_PKT_INT_EN BIT(1) 73#define DP83822_SLEEP_MODE_INT_EN BIT(2) 74#define DP83822_MDI_XOVER_INT_EN BIT(3) 75#define DP83822_LB_FIFO_INT_EN BIT(4) 76#define DP83822_PAGE_RX_INT_EN BIT(5) 77#define DP83822_ANEG_ERR_INT_EN BIT(6) 78#define DP83822_EEE_ERROR_CHANGE_INT_EN BIT(7) 79 80/* INT_STAT1 bits */ 81#define DP83822_WOL_INT_EN BIT(4) 82#define DP83822_WOL_INT_STAT BIT(12) 83 84#define MII_DP83822_RXSOP1 0x04a5 85#define MII_DP83822_RXSOP2 0x04a6 86#define MII_DP83822_RXSOP3 0x04a7 87 88/* WoL Registers */ 89#define MII_DP83822_WOL_CFG 0x04a0 90#define MII_DP83822_WOL_STAT 0x04a1 91#define MII_DP83822_WOL_DA1 0x04a2 92#define MII_DP83822_WOL_DA2 0x04a3 93#define MII_DP83822_WOL_DA3 0x04a4 94 95/* WoL bits */ 96#define DP83822_WOL_MAGIC_EN BIT(0) 97#define DP83822_WOL_SECURE_ON BIT(5) 98#define DP83822_WOL_EN BIT(7) 99#define DP83822_WOL_INDICATION_SEL BIT(8) 100#define DP83822_WOL_CLR_INDICATION BIT(11) 101 102/* RCSR bits */ 103#define DP83822_RMII_MODE_EN BIT(5) 104#define DP83822_RMII_MODE_SEL BIT(7) 105#define DP83822_RGMII_MODE_EN BIT(9) 106#define DP83822_RX_CLK_SHIFT BIT(12) 107#define DP83822_TX_CLK_SHIFT BIT(11) 108 109/* SOR1 mode */ 110#define DP83822_STRAP_MODE1 0 111#define DP83822_STRAP_MODE2 BIT(0) 112#define DP83822_STRAP_MODE3 BIT(1) 113#define DP83822_STRAP_MODE4 GENMASK(1, 0) 114 115#define DP83822_COL_STRAP_MASK GENMASK(11, 10) 116#define DP83822_COL_SHIFT 10 117#define DP83822_RX_ER_STR_MASK GENMASK(9, 8) 118#define DP83822_RX_ER_SHIFT 8 119 120/* DP83826: VOD_CFG1 & VOD_CFG2 */ 121#define DP83826_VOD_CFG1_MINUS_MDIX_MASK GENMASK(13, 12) 122#define DP83826_VOD_CFG1_MINUS_MDI_MASK GENMASK(11, 6) 123#define DP83826_VOD_CFG2_MINUS_MDIX_MASK GENMASK(15, 12) 124#define DP83826_VOD_CFG2_PLUS_MDIX_MASK GENMASK(11, 6) 125#define DP83826_VOD_CFG2_PLUS_MDI_MASK GENMASK(5, 0) 126#define DP83826_CFG_DAC_MINUS_MDIX_5_TO_4 GENMASK(5, 4) 127#define DP83826_CFG_DAC_MINUS_MDIX_3_TO_0 GENMASK(3, 0) 128#define DP83826_CFG_DAC_PERCENT_PER_STEP 625 129#define DP83826_CFG_DAC_PERCENT_DEFAULT 10000 130#define DP83826_CFG_DAC_MINUS_DEFAULT 0x30 131#define DP83826_CFG_DAC_PLUS_DEFAULT 0x10 132 133#define MII_DP83822_FIBER_ADVERTISE (ADVERTISED_TP | ADVERTISED_MII | \ 134 ADVERTISED_FIBRE | \ 135 ADVERTISED_Pause | ADVERTISED_Asym_Pause) 136 137struct dp83822_private { 138 bool fx_signal_det_low; 139 int fx_enabled; 140 u16 fx_sd_enable; 141 u8 cfg_dac_minus; 142 u8 cfg_dac_plus; 143}; 144 145static int dp83822_set_wol(struct phy_device *phydev, 146 struct ethtool_wolinfo *wol) 147{ 148 struct net_device *ndev = phydev->attached_dev; 149 u16 value; 150 const u8 *mac; 151 152 if (wol->wolopts & (WAKE_MAGIC | WAKE_MAGICSECURE)) { 153 mac = (const u8 *)ndev->dev_addr; 154 155 if (!is_valid_ether_addr(mac)) 156 return -EINVAL; 157 158 /* MAC addresses start with byte 5, but stored in mac[0]. 159 * 822 PHYs store bytes 4|5, 2|3, 0|1 160 */ 161 phy_write_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_DA1, 162 (mac[1] << 8) | mac[0]); 163 phy_write_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_DA2, 164 (mac[3] << 8) | mac[2]); 165 phy_write_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_DA3, 166 (mac[5] << 8) | mac[4]); 167 168 value = phy_read_mmd(phydev, DP83822_DEVADDR, 169 MII_DP83822_WOL_CFG); 170 if (wol->wolopts & WAKE_MAGIC) 171 value |= DP83822_WOL_MAGIC_EN; 172 else 173 value &= ~DP83822_WOL_MAGIC_EN; 174 175 if (wol->wolopts & WAKE_MAGICSECURE) { 176 phy_write_mmd(phydev, DP83822_DEVADDR, 177 MII_DP83822_RXSOP1, 178 (wol->sopass[1] << 8) | wol->sopass[0]); 179 phy_write_mmd(phydev, DP83822_DEVADDR, 180 MII_DP83822_RXSOP2, 181 (wol->sopass[3] << 8) | wol->sopass[2]); 182 phy_write_mmd(phydev, DP83822_DEVADDR, 183 MII_DP83822_RXSOP3, 184 (wol->sopass[5] << 8) | wol->sopass[4]); 185 value |= DP83822_WOL_SECURE_ON; 186 } else { 187 value &= ~DP83822_WOL_SECURE_ON; 188 } 189 190 /* Clear any pending WoL interrupt */ 191 phy_read(phydev, MII_DP83822_MISR2); 192 193 value |= DP83822_WOL_EN | DP83822_WOL_INDICATION_SEL | 194 DP83822_WOL_CLR_INDICATION; 195 196 return phy_write_mmd(phydev, DP83822_DEVADDR, 197 MII_DP83822_WOL_CFG, value); 198 } else { 199 return phy_clear_bits_mmd(phydev, DP83822_DEVADDR, 200 MII_DP83822_WOL_CFG, DP83822_WOL_EN); 201 } 202} 203 204static void dp83822_get_wol(struct phy_device *phydev, 205 struct ethtool_wolinfo *wol) 206{ 207 int value; 208 u16 sopass_val; 209 210 wol->supported = (WAKE_MAGIC | WAKE_MAGICSECURE); 211 wol->wolopts = 0; 212 213 value = phy_read_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_CFG); 214 215 if (value & DP83822_WOL_MAGIC_EN) 216 wol->wolopts |= WAKE_MAGIC; 217 218 if (value & DP83822_WOL_SECURE_ON) { 219 sopass_val = phy_read_mmd(phydev, DP83822_DEVADDR, 220 MII_DP83822_RXSOP1); 221 wol->sopass[0] = (sopass_val & 0xff); 222 wol->sopass[1] = (sopass_val >> 8); 223 224 sopass_val = phy_read_mmd(phydev, DP83822_DEVADDR, 225 MII_DP83822_RXSOP2); 226 wol->sopass[2] = (sopass_val & 0xff); 227 wol->sopass[3] = (sopass_val >> 8); 228 229 sopass_val = phy_read_mmd(phydev, DP83822_DEVADDR, 230 MII_DP83822_RXSOP3); 231 wol->sopass[4] = (sopass_val & 0xff); 232 wol->sopass[5] = (sopass_val >> 8); 233 234 wol->wolopts |= WAKE_MAGICSECURE; 235 } 236 237 /* WoL is not enabled so set wolopts to 0 */ 238 if (!(value & DP83822_WOL_EN)) 239 wol->wolopts = 0; 240} 241 242static int dp83822_config_intr(struct phy_device *phydev) 243{ 244 struct dp83822_private *dp83822 = phydev->priv; 245 int misr_status; 246 int physcr_status; 247 int err; 248 249 if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { 250 misr_status = phy_read(phydev, MII_DP83822_MISR1); 251 if (misr_status < 0) 252 return misr_status; 253 254 misr_status |= (DP83822_LINK_STAT_INT_EN | 255 DP83822_ENERGY_DET_INT_EN | 256 DP83822_LINK_QUAL_INT_EN); 257 258 /* Private data pointer is NULL on DP83825 */ 259 if (!dp83822 || !dp83822->fx_enabled) 260 misr_status |= DP83822_ANEG_COMPLETE_INT_EN | 261 DP83822_DUP_MODE_CHANGE_INT_EN | 262 DP83822_SPEED_CHANGED_INT_EN; 263 264 265 err = phy_write(phydev, MII_DP83822_MISR1, misr_status); 266 if (err < 0) 267 return err; 268 269 misr_status = phy_read(phydev, MII_DP83822_MISR2); 270 if (misr_status < 0) 271 return misr_status; 272 273 misr_status |= (DP83822_JABBER_DET_INT_EN | 274 DP83822_SLEEP_MODE_INT_EN | 275 DP83822_LB_FIFO_INT_EN | 276 DP83822_PAGE_RX_INT_EN | 277 DP83822_EEE_ERROR_CHANGE_INT_EN); 278 279 /* Private data pointer is NULL on DP83825 */ 280 if (!dp83822 || !dp83822->fx_enabled) 281 misr_status |= DP83822_ANEG_ERR_INT_EN | 282 DP83822_WOL_PKT_INT_EN; 283 284 err = phy_write(phydev, MII_DP83822_MISR2, misr_status); 285 if (err < 0) 286 return err; 287 288 physcr_status = phy_read(phydev, MII_DP83822_PHYSCR); 289 if (physcr_status < 0) 290 return physcr_status; 291 292 physcr_status |= DP83822_PHYSCR_INT_OE | DP83822_PHYSCR_INTEN; 293 294 } else { 295 err = phy_write(phydev, MII_DP83822_MISR1, 0); 296 if (err < 0) 297 return err; 298 299 err = phy_write(phydev, MII_DP83822_MISR2, 0); 300 if (err < 0) 301 return err; 302 303 physcr_status = phy_read(phydev, MII_DP83822_PHYSCR); 304 if (physcr_status < 0) 305 return physcr_status; 306 307 physcr_status &= ~DP83822_PHYSCR_INTEN; 308 } 309 310 return phy_write(phydev, MII_DP83822_PHYSCR, physcr_status); 311} 312 313static irqreturn_t dp83822_handle_interrupt(struct phy_device *phydev) 314{ 315 bool trigger_machine = false; 316 int irq_status; 317 318 /* The MISR1 and MISR2 registers are holding the interrupt status in 319 * the upper half (15:8), while the lower half (7:0) is used for 320 * controlling the interrupt enable state of those individual interrupt 321 * sources. To determine the possible interrupt sources, just read the 322 * MISR* register and use it directly to know which interrupts have 323 * been enabled previously or not. 324 */ 325 irq_status = phy_read(phydev, MII_DP83822_MISR1); 326 if (irq_status < 0) { 327 phy_error(phydev); 328 return IRQ_NONE; 329 } 330 if (irq_status & ((irq_status & GENMASK(7, 0)) << 8)) 331 trigger_machine = true; 332 333 irq_status = phy_read(phydev, MII_DP83822_MISR2); 334 if (irq_status < 0) { 335 phy_error(phydev); 336 return IRQ_NONE; 337 } 338 if (irq_status & ((irq_status & GENMASK(7, 0)) << 8)) 339 trigger_machine = true; 340 341 if (!trigger_machine) 342 return IRQ_NONE; 343 344 phy_trigger_machine(phydev); 345 346 return IRQ_HANDLED; 347} 348 349static int dp8382x_disable_wol(struct phy_device *phydev) 350{ 351 return phy_clear_bits_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_CFG, 352 DP83822_WOL_EN | DP83822_WOL_MAGIC_EN | 353 DP83822_WOL_SECURE_ON); 354} 355 356static int dp83822_read_status(struct phy_device *phydev) 357{ 358 struct dp83822_private *dp83822 = phydev->priv; 359 int status = phy_read(phydev, MII_DP83822_PHYSTS); 360 int ctrl2; 361 int ret; 362 363 if (dp83822->fx_enabled) { 364 if (status & DP83822_PHYSTS_LINK) { 365 phydev->speed = SPEED_UNKNOWN; 366 phydev->duplex = DUPLEX_UNKNOWN; 367 } else { 368 ctrl2 = phy_read(phydev, MII_DP83822_CTRL_2); 369 if (ctrl2 < 0) 370 return ctrl2; 371 372 if (!(ctrl2 & DP83822_FX_ENABLE)) { 373 ret = phy_write(phydev, MII_DP83822_CTRL_2, 374 DP83822_FX_ENABLE | ctrl2); 375 if (ret < 0) 376 return ret; 377 } 378 } 379 } 380 381 ret = genphy_read_status(phydev); 382 if (ret) 383 return ret; 384 385 if (status < 0) 386 return status; 387 388 if (status & DP83822_PHYSTS_DUPLEX) 389 phydev->duplex = DUPLEX_FULL; 390 else 391 phydev->duplex = DUPLEX_HALF; 392 393 if (status & DP83822_PHYSTS_10) 394 phydev->speed = SPEED_10; 395 else 396 phydev->speed = SPEED_100; 397 398 return 0; 399} 400 401static int dp83822_config_init(struct phy_device *phydev) 402{ 403 struct dp83822_private *dp83822 = phydev->priv; 404 struct device *dev = &phydev->mdio.dev; 405 int rgmii_delay = 0; 406 s32 rx_int_delay; 407 s32 tx_int_delay; 408 int err = 0; 409 int bmcr; 410 411 if (phy_interface_is_rgmii(phydev)) { 412 rx_int_delay = phy_get_internal_delay(phydev, dev, NULL, 0, 413 true); 414 415 /* Set DP83822_RX_CLK_SHIFT to enable rx clk internal delay */ 416 if (rx_int_delay > 0) 417 rgmii_delay |= DP83822_RX_CLK_SHIFT; 418 419 tx_int_delay = phy_get_internal_delay(phydev, dev, NULL, 0, 420 false); 421 422 /* Set DP83822_TX_CLK_SHIFT to disable tx clk internal delay */ 423 if (tx_int_delay <= 0) 424 rgmii_delay |= DP83822_TX_CLK_SHIFT; 425 426 err = phy_modify_mmd(phydev, DP83822_DEVADDR, MII_DP83822_RCSR, 427 DP83822_RX_CLK_SHIFT | DP83822_TX_CLK_SHIFT, rgmii_delay); 428 if (err) 429 return err; 430 431 err = phy_set_bits_mmd(phydev, DP83822_DEVADDR, 432 MII_DP83822_RCSR, DP83822_RGMII_MODE_EN); 433 434 if (err) 435 return err; 436 } else { 437 err = phy_clear_bits_mmd(phydev, DP83822_DEVADDR, 438 MII_DP83822_RCSR, DP83822_RGMII_MODE_EN); 439 440 if (err) 441 return err; 442 } 443 444 if (dp83822->fx_enabled) { 445 err = phy_modify(phydev, MII_DP83822_CTRL_2, 446 DP83822_FX_ENABLE, 1); 447 if (err < 0) 448 return err; 449 450 /* Only allow advertising what this PHY supports */ 451 linkmode_and(phydev->advertising, phydev->advertising, 452 phydev->supported); 453 454 linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, 455 phydev->supported); 456 linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, 457 phydev->advertising); 458 linkmode_set_bit(ETHTOOL_LINK_MODE_100baseFX_Full_BIT, 459 phydev->supported); 460 linkmode_set_bit(ETHTOOL_LINK_MODE_100baseFX_Half_BIT, 461 phydev->supported); 462 linkmode_set_bit(ETHTOOL_LINK_MODE_100baseFX_Full_BIT, 463 phydev->advertising); 464 linkmode_set_bit(ETHTOOL_LINK_MODE_100baseFX_Half_BIT, 465 phydev->advertising); 466 467 /* Auto neg is not supported in fiber mode */ 468 bmcr = phy_read(phydev, MII_BMCR); 469 if (bmcr < 0) 470 return bmcr; 471 472 if (bmcr & BMCR_ANENABLE) { 473 err = phy_modify(phydev, MII_BMCR, BMCR_ANENABLE, 0); 474 if (err < 0) 475 return err; 476 } 477 phydev->autoneg = AUTONEG_DISABLE; 478 linkmode_clear_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, 479 phydev->supported); 480 linkmode_clear_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, 481 phydev->advertising); 482 483 /* Setup fiber advertisement */ 484 err = phy_modify_changed(phydev, MII_ADVERTISE, 485 MII_DP83822_FIBER_ADVERTISE, 486 MII_DP83822_FIBER_ADVERTISE); 487 488 if (err < 0) 489 return err; 490 491 if (dp83822->fx_signal_det_low) { 492 err = phy_set_bits_mmd(phydev, DP83822_DEVADDR, 493 MII_DP83822_GENCFG, 494 DP83822_SIG_DET_LOW); 495 if (err) 496 return err; 497 } 498 } 499 return dp8382x_disable_wol(phydev); 500} 501 502static int dp83826_config_rmii_mode(struct phy_device *phydev) 503{ 504 struct device *dev = &phydev->mdio.dev; 505 const char *of_val; 506 int ret; 507 508 if (!device_property_read_string(dev, "ti,rmii-mode", &of_val)) { 509 if (strcmp(of_val, "master") == 0) { 510 ret = phy_clear_bits_mmd(phydev, DP83822_DEVADDR, MII_DP83822_RCSR, 511 DP83822_RMII_MODE_SEL); 512 } else if (strcmp(of_val, "slave") == 0) { 513 ret = phy_set_bits_mmd(phydev, DP83822_DEVADDR, MII_DP83822_RCSR, 514 DP83822_RMII_MODE_SEL); 515 } else { 516 phydev_err(phydev, "Invalid value for ti,rmii-mode property (%s)\n", 517 of_val); 518 ret = -EINVAL; 519 } 520 521 if (ret) 522 return ret; 523 } 524 525 return 0; 526} 527 528static int dp83826_config_init(struct phy_device *phydev) 529{ 530 struct dp83822_private *dp83822 = phydev->priv; 531 u16 val, mask; 532 int ret; 533 534 if (phydev->interface == PHY_INTERFACE_MODE_RMII) { 535 ret = phy_set_bits_mmd(phydev, DP83822_DEVADDR, MII_DP83822_RCSR, 536 DP83822_RMII_MODE_EN); 537 if (ret) 538 return ret; 539 540 ret = dp83826_config_rmii_mode(phydev); 541 if (ret) 542 return ret; 543 } else { 544 ret = phy_clear_bits_mmd(phydev, DP83822_DEVADDR, MII_DP83822_RCSR, 545 DP83822_RMII_MODE_EN); 546 if (ret) 547 return ret; 548 } 549 550 if (dp83822->cfg_dac_minus != DP83826_CFG_DAC_MINUS_DEFAULT) { 551 val = FIELD_PREP(DP83826_VOD_CFG1_MINUS_MDI_MASK, dp83822->cfg_dac_minus) | 552 FIELD_PREP(DP83826_VOD_CFG1_MINUS_MDIX_MASK, 553 FIELD_GET(DP83826_CFG_DAC_MINUS_MDIX_5_TO_4, 554 dp83822->cfg_dac_minus)); 555 mask = DP83826_VOD_CFG1_MINUS_MDIX_MASK | DP83826_VOD_CFG1_MINUS_MDI_MASK; 556 ret = phy_modify_mmd(phydev, DP83822_DEVADDR, MII_DP83826_VOD_CFG1, mask, val); 557 if (ret) 558 return ret; 559 560 val = FIELD_PREP(DP83826_VOD_CFG2_MINUS_MDIX_MASK, 561 FIELD_GET(DP83826_CFG_DAC_MINUS_MDIX_3_TO_0, 562 dp83822->cfg_dac_minus)); 563 mask = DP83826_VOD_CFG2_MINUS_MDIX_MASK; 564 ret = phy_modify_mmd(phydev, DP83822_DEVADDR, MII_DP83826_VOD_CFG2, mask, val); 565 if (ret) 566 return ret; 567 } 568 569 if (dp83822->cfg_dac_plus != DP83826_CFG_DAC_PLUS_DEFAULT) { 570 val = FIELD_PREP(DP83826_VOD_CFG2_PLUS_MDIX_MASK, dp83822->cfg_dac_plus) | 571 FIELD_PREP(DP83826_VOD_CFG2_PLUS_MDI_MASK, dp83822->cfg_dac_plus); 572 mask = DP83826_VOD_CFG2_PLUS_MDIX_MASK | DP83826_VOD_CFG2_PLUS_MDI_MASK; 573 ret = phy_modify_mmd(phydev, DP83822_DEVADDR, MII_DP83826_VOD_CFG2, mask, val); 574 if (ret) 575 return ret; 576 } 577 578 return dp8382x_disable_wol(phydev); 579} 580 581static int dp8382x_config_init(struct phy_device *phydev) 582{ 583 return dp8382x_disable_wol(phydev); 584} 585 586static int dp83822_phy_reset(struct phy_device *phydev) 587{ 588 int err; 589 590 err = phy_write(phydev, MII_DP83822_RESET_CTRL, DP83822_SW_RESET); 591 if (err < 0) 592 return err; 593 594 return phydev->drv->config_init(phydev); 595} 596 597#ifdef CONFIG_OF_MDIO 598static int dp83822_of_init(struct phy_device *phydev) 599{ 600 struct dp83822_private *dp83822 = phydev->priv; 601 struct device *dev = &phydev->mdio.dev; 602 603 /* Signal detection for the PHY is only enabled if the FX_EN and the 604 * SD_EN pins are strapped. Signal detection can only enabled if FX_EN 605 * is strapped otherwise signal detection is disabled for the PHY. 606 */ 607 if (dp83822->fx_enabled && dp83822->fx_sd_enable) 608 dp83822->fx_signal_det_low = device_property_present(dev, 609 "ti,link-loss-low"); 610 if (!dp83822->fx_enabled) 611 dp83822->fx_enabled = device_property_present(dev, 612 "ti,fiber-mode"); 613 614 return 0; 615} 616 617static int dp83826_to_dac_minus_one_regval(int percent) 618{ 619 int tmp = DP83826_CFG_DAC_PERCENT_DEFAULT - percent; 620 621 return tmp / DP83826_CFG_DAC_PERCENT_PER_STEP; 622} 623 624static int dp83826_to_dac_plus_one_regval(int percent) 625{ 626 int tmp = percent - DP83826_CFG_DAC_PERCENT_DEFAULT; 627 628 return tmp / DP83826_CFG_DAC_PERCENT_PER_STEP; 629} 630 631static void dp83826_of_init(struct phy_device *phydev) 632{ 633 struct dp83822_private *dp83822 = phydev->priv; 634 struct device *dev = &phydev->mdio.dev; 635 u32 val; 636 637 dp83822->cfg_dac_minus = DP83826_CFG_DAC_MINUS_DEFAULT; 638 if (!device_property_read_u32(dev, "ti,cfg-dac-minus-one-bp", &val)) 639 dp83822->cfg_dac_minus += dp83826_to_dac_minus_one_regval(val); 640 641 dp83822->cfg_dac_plus = DP83826_CFG_DAC_PLUS_DEFAULT; 642 if (!device_property_read_u32(dev, "ti,cfg-dac-plus-one-bp", &val)) 643 dp83822->cfg_dac_plus += dp83826_to_dac_plus_one_regval(val); 644} 645#else 646static int dp83822_of_init(struct phy_device *phydev) 647{ 648 return 0; 649} 650 651static void dp83826_of_init(struct phy_device *phydev) 652{ 653} 654#endif /* CONFIG_OF_MDIO */ 655 656static int dp83822_read_straps(struct phy_device *phydev) 657{ 658 struct dp83822_private *dp83822 = phydev->priv; 659 int fx_enabled, fx_sd_enable; 660 int val; 661 662 val = phy_read_mmd(phydev, DP83822_DEVADDR, MII_DP83822_SOR1); 663 if (val < 0) 664 return val; 665 666 phydev_dbg(phydev, "SOR1 strap register: 0x%04x\n", val); 667 668 fx_enabled = (val & DP83822_COL_STRAP_MASK) >> DP83822_COL_SHIFT; 669 if (fx_enabled == DP83822_STRAP_MODE2 || 670 fx_enabled == DP83822_STRAP_MODE3) 671 dp83822->fx_enabled = 1; 672 673 if (dp83822->fx_enabled) { 674 fx_sd_enable = (val & DP83822_RX_ER_STR_MASK) >> DP83822_RX_ER_SHIFT; 675 if (fx_sd_enable == DP83822_STRAP_MODE3 || 676 fx_sd_enable == DP83822_STRAP_MODE4) 677 dp83822->fx_sd_enable = 1; 678 } 679 680 return 0; 681} 682 683static int dp83822_probe(struct phy_device *phydev) 684{ 685 struct dp83822_private *dp83822; 686 int ret; 687 688 dp83822 = devm_kzalloc(&phydev->mdio.dev, sizeof(*dp83822), 689 GFP_KERNEL); 690 if (!dp83822) 691 return -ENOMEM; 692 693 phydev->priv = dp83822; 694 695 ret = dp83822_read_straps(phydev); 696 if (ret) 697 return ret; 698 699 dp83822_of_init(phydev); 700 701 if (dp83822->fx_enabled) 702 phydev->port = PORT_FIBRE; 703 704 return 0; 705} 706 707static int dp83826_probe(struct phy_device *phydev) 708{ 709 struct dp83822_private *dp83822; 710 711 dp83822 = devm_kzalloc(&phydev->mdio.dev, sizeof(*dp83822), 712 GFP_KERNEL); 713 if (!dp83822) 714 return -ENOMEM; 715 716 phydev->priv = dp83822; 717 718 dp83826_of_init(phydev); 719 720 return 0; 721} 722 723static int dp83822_suspend(struct phy_device *phydev) 724{ 725 int value; 726 727 value = phy_read_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_CFG); 728 729 if (!(value & DP83822_WOL_EN)) 730 genphy_suspend(phydev); 731 732 return 0; 733} 734 735static int dp83822_resume(struct phy_device *phydev) 736{ 737 int value; 738 739 genphy_resume(phydev); 740 741 value = phy_read_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_CFG); 742 743 phy_write_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_CFG, value | 744 DP83822_WOL_CLR_INDICATION); 745 746 return 0; 747} 748 749#define DP83822_PHY_DRIVER(_id, _name) \ 750 { \ 751 PHY_ID_MATCH_MODEL(_id), \ 752 .name = (_name), \ 753 /* PHY_BASIC_FEATURES */ \ 754 .probe = dp83822_probe, \ 755 .soft_reset = dp83822_phy_reset, \ 756 .config_init = dp83822_config_init, \ 757 .read_status = dp83822_read_status, \ 758 .get_wol = dp83822_get_wol, \ 759 .set_wol = dp83822_set_wol, \ 760 .config_intr = dp83822_config_intr, \ 761 .handle_interrupt = dp83822_handle_interrupt, \ 762 .suspend = dp83822_suspend, \ 763 .resume = dp83822_resume, \ 764 } 765 766#define DP83826_PHY_DRIVER(_id, _name) \ 767 { \ 768 PHY_ID_MATCH_MODEL(_id), \ 769 .name = (_name), \ 770 /* PHY_BASIC_FEATURES */ \ 771 .probe = dp83826_probe, \ 772 .soft_reset = dp83822_phy_reset, \ 773 .config_init = dp83826_config_init, \ 774 .get_wol = dp83822_get_wol, \ 775 .set_wol = dp83822_set_wol, \ 776 .config_intr = dp83822_config_intr, \ 777 .handle_interrupt = dp83822_handle_interrupt, \ 778 .suspend = dp83822_suspend, \ 779 .resume = dp83822_resume, \ 780 } 781 782#define DP8382X_PHY_DRIVER(_id, _name) \ 783 { \ 784 PHY_ID_MATCH_MODEL(_id), \ 785 .name = (_name), \ 786 /* PHY_BASIC_FEATURES */ \ 787 .soft_reset = dp83822_phy_reset, \ 788 .config_init = dp8382x_config_init, \ 789 .get_wol = dp83822_get_wol, \ 790 .set_wol = dp83822_set_wol, \ 791 .config_intr = dp83822_config_intr, \ 792 .handle_interrupt = dp83822_handle_interrupt, \ 793 .suspend = dp83822_suspend, \ 794 .resume = dp83822_resume, \ 795 } 796 797static struct phy_driver dp83822_driver[] = { 798 DP83822_PHY_DRIVER(DP83822_PHY_ID, "TI DP83822"), 799 DP8382X_PHY_DRIVER(DP83825I_PHY_ID, "TI DP83825I"), 800 DP83826_PHY_DRIVER(DP83826C_PHY_ID, "TI DP83826C"), 801 DP83826_PHY_DRIVER(DP83826NC_PHY_ID, "TI DP83826NC"), 802 DP8382X_PHY_DRIVER(DP83825S_PHY_ID, "TI DP83825S"), 803 DP8382X_PHY_DRIVER(DP83825CM_PHY_ID, "TI DP83825M"), 804 DP8382X_PHY_DRIVER(DP83825CS_PHY_ID, "TI DP83825CS"), 805}; 806module_phy_driver(dp83822_driver); 807 808static struct mdio_device_id __maybe_unused dp83822_tbl[] = { 809 { DP83822_PHY_ID, 0xfffffff0 }, 810 { DP83825I_PHY_ID, 0xfffffff0 }, 811 { DP83826C_PHY_ID, 0xfffffff0 }, 812 { DP83826NC_PHY_ID, 0xfffffff0 }, 813 { DP83825S_PHY_ID, 0xfffffff0 }, 814 { DP83825CM_PHY_ID, 0xfffffff0 }, 815 { DP83825CS_PHY_ID, 0xfffffff0 }, 816 { }, 817}; 818MODULE_DEVICE_TABLE(mdio, dp83822_tbl); 819 820MODULE_DESCRIPTION("Texas Instruments DP83822 PHY driver"); 821MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com"); 822MODULE_LICENSE("GPL v2"); 823