1/* SPDX-License-Identifier: GPL-2.0 */
2/****************************************************************************/
3
4/*
5 *	fec.h  --  Fast Ethernet Controller for Motorola ColdFire SoC
6 *		   processors.
7 *
8 *	(C) Copyright 2000-2005, Greg Ungerer (gerg@snapgear.com)
9 *	(C) Copyright 2000-2001, Lineo (www.lineo.com)
10 */
11
12/****************************************************************************/
13#ifndef FEC_H
14#define	FEC_H
15/****************************************************************************/
16
17#include <linux/clocksource.h>
18#include <linux/net_tstamp.h>
19#include <linux/pm_qos.h>
20#include <linux/bpf.h>
21#include <linux/ptp_clock_kernel.h>
22#include <linux/timecounter.h>
23#include <dt-bindings/firmware/imx/rsrc.h>
24#include <linux/firmware/imx/sci.h>
25#include <net/xdp.h>
26
27#if defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x) || \
28    defined(CONFIG_M520x) || defined(CONFIG_M532x) || defined(CONFIG_ARM) || \
29    defined(CONFIG_ARM64) || defined(CONFIG_COMPILE_TEST)
30/*
31 *	Just figures, Motorola would have to change the offsets for
32 *	registers in the same peripheral device on different models
33 *	of the ColdFire!
34 */
35#define FEC_IEVENT		0x004 /* Interrupt event reg */
36#define FEC_IMASK		0x008 /* Interrupt mask reg */
37#define FEC_R_DES_ACTIVE_0	0x010 /* Receive descriptor reg */
38#define FEC_X_DES_ACTIVE_0	0x014 /* Transmit descriptor reg */
39#define FEC_ECNTRL		0x024 /* Ethernet control reg */
40#define FEC_MII_DATA		0x040 /* MII manage frame reg */
41#define FEC_MII_SPEED		0x044 /* MII speed control reg */
42#define FEC_MIB_CTRLSTAT	0x064 /* MIB control/status reg */
43#define FEC_R_CNTRL		0x084 /* Receive control reg */
44#define FEC_X_CNTRL		0x0c4 /* Transmit Control reg */
45#define FEC_ADDR_LOW		0x0e4 /* Low 32bits MAC address */
46#define FEC_ADDR_HIGH		0x0e8 /* High 16bits MAC address */
47#define FEC_OPD			0x0ec /* Opcode + Pause duration */
48#define FEC_TXIC0		0x0f0 /* Tx Interrupt Coalescing for ring 0 */
49#define FEC_TXIC1		0x0f4 /* Tx Interrupt Coalescing for ring 1 */
50#define FEC_TXIC2		0x0f8 /* Tx Interrupt Coalescing for ring 2 */
51#define FEC_RXIC0		0x100 /* Rx Interrupt Coalescing for ring 0 */
52#define FEC_RXIC1		0x104 /* Rx Interrupt Coalescing for ring 1 */
53#define FEC_RXIC2		0x108 /* Rx Interrupt Coalescing for ring 2 */
54#define FEC_HASH_TABLE_HIGH	0x118 /* High 32bits hash table */
55#define FEC_HASH_TABLE_LOW	0x11c /* Low 32bits hash table */
56#define FEC_GRP_HASH_TABLE_HIGH	0x120 /* High 32bits hash table */
57#define FEC_GRP_HASH_TABLE_LOW	0x124 /* Low 32bits hash table */
58#define FEC_X_WMRK		0x144 /* FIFO transmit water mark */
59#define FEC_R_BOUND		0x14c /* FIFO receive bound reg */
60#define FEC_R_FSTART		0x150 /* FIFO receive start reg */
61#define FEC_R_DES_START_1	0x160 /* Receive descriptor ring 1 */
62#define FEC_X_DES_START_1	0x164 /* Transmit descriptor ring 1 */
63#define FEC_R_BUFF_SIZE_1	0x168 /* Maximum receive buff ring1 size */
64#define FEC_R_DES_START_2	0x16c /* Receive descriptor ring 2 */
65#define FEC_X_DES_START_2	0x170 /* Transmit descriptor ring 2 */
66#define FEC_R_BUFF_SIZE_2	0x174 /* Maximum receive buff ring2 size */
67#define FEC_R_DES_START_0	0x180 /* Receive descriptor ring */
68#define FEC_X_DES_START_0	0x184 /* Transmit descriptor ring */
69#define FEC_R_BUFF_SIZE_0	0x188 /* Maximum receive buff size */
70#define FEC_R_FIFO_RSFL		0x190 /* Receive FIFO section full threshold */
71#define FEC_R_FIFO_RSEM		0x194 /* Receive FIFO section empty threshold */
72#define FEC_R_FIFO_RAEM		0x198 /* Receive FIFO almost empty threshold */
73#define FEC_R_FIFO_RAFL		0x19c /* Receive FIFO almost full threshold */
74#define FEC_FTRL		0x1b0 /* Frame truncation receive length*/
75#define FEC_RACC		0x1c4 /* Receive Accelerator function */
76#define FEC_RCMR_1		0x1c8 /* Receive classification match ring 1 */
77#define FEC_RCMR_2		0x1cc /* Receive classification match ring 2 */
78#define FEC_DMA_CFG_1		0x1d8 /* DMA class configuration for ring 1 */
79#define FEC_DMA_CFG_2		0x1dc /* DMA class Configuration for ring 2 */
80#define FEC_R_DES_ACTIVE_1	0x1e0 /* Rx descriptor active for ring 1 */
81#define FEC_X_DES_ACTIVE_1	0x1e4 /* Tx descriptor active for ring 1 */
82#define FEC_R_DES_ACTIVE_2	0x1e8 /* Rx descriptor active for ring 2 */
83#define FEC_X_DES_ACTIVE_2	0x1ec /* Tx descriptor active for ring 2 */
84#define FEC_QOS_SCHEME		0x1f0 /* Set multi queues Qos scheme */
85#define FEC_LPI_SLEEP		0x1f4 /* Set IEEE802.3az LPI Sleep Ts time */
86#define FEC_LPI_WAKE		0x1f8 /* Set IEEE802.3az LPI Wake Tw time */
87#define FEC_MIIGSK_CFGR		0x300 /* MIIGSK Configuration reg */
88#define FEC_MIIGSK_ENR		0x308 /* MIIGSK Enable reg */
89
90#define BM_MIIGSK_CFGR_MII		0x00
91#define BM_MIIGSK_CFGR_RMII		0x01
92#define BM_MIIGSK_CFGR_FRCONT_10M	0x40
93
94#define RMON_T_DROP		0x200 /* Count of frames not cntd correctly */
95#define RMON_T_PACKETS		0x204 /* RMON TX packet count */
96#define RMON_T_BC_PKT		0x208 /* RMON TX broadcast pkts */
97#define RMON_T_MC_PKT		0x20c /* RMON TX multicast pkts */
98#define RMON_T_CRC_ALIGN	0x210 /* RMON TX pkts with CRC align err */
99#define RMON_T_UNDERSIZE	0x214 /* RMON TX pkts < 64 bytes, good CRC */
100#define RMON_T_OVERSIZE		0x218 /* RMON TX pkts > MAX_FL bytes good CRC */
101#define RMON_T_FRAG		0x21c /* RMON TX pkts < 64 bytes, bad CRC */
102#define RMON_T_JAB		0x220 /* RMON TX pkts > MAX_FL bytes, bad CRC */
103#define RMON_T_COL		0x224 /* RMON TX collision count */
104#define RMON_T_P64		0x228 /* RMON TX 64 byte pkts */
105#define RMON_T_P65TO127		0x22c /* RMON TX 65 to 127 byte pkts */
106#define RMON_T_P128TO255	0x230 /* RMON TX 128 to 255 byte pkts */
107#define RMON_T_P256TO511	0x234 /* RMON TX 256 to 511 byte pkts */
108#define RMON_T_P512TO1023	0x238 /* RMON TX 512 to 1023 byte pkts */
109#define RMON_T_P1024TO2047	0x23c /* RMON TX 1024 to 2047 byte pkts */
110#define RMON_T_P_GTE2048	0x240 /* RMON TX pkts > 2048 bytes */
111#define RMON_T_OCTETS		0x244 /* RMON TX octets */
112#define IEEE_T_DROP		0x248 /* Count of frames not counted crtly */
113#define IEEE_T_FRAME_OK		0x24c /* Frames tx'd OK */
114#define IEEE_T_1COL		0x250 /* Frames tx'd with single collision */
115#define IEEE_T_MCOL		0x254 /* Frames tx'd with multiple collision */
116#define IEEE_T_DEF		0x258 /* Frames tx'd after deferral delay */
117#define IEEE_T_LCOL		0x25c /* Frames tx'd with late collision */
118#define IEEE_T_EXCOL		0x260 /* Frames tx'd with excesv collisions */
119#define IEEE_T_MACERR		0x264 /* Frames tx'd with TX FIFO underrun */
120#define IEEE_T_CSERR		0x268 /* Frames tx'd with carrier sense err */
121#define IEEE_T_SQE		0x26c /* Frames tx'd with SQE err */
122#define IEEE_T_FDXFC		0x270 /* Flow control pause frames tx'd */
123#define IEEE_T_OCTETS_OK	0x274 /* Octet count for frames tx'd w/o err */
124#define RMON_R_PACKETS		0x284 /* RMON RX packet count */
125#define RMON_R_BC_PKT		0x288 /* RMON RX broadcast pkts */
126#define RMON_R_MC_PKT		0x28c /* RMON RX multicast pkts */
127#define RMON_R_CRC_ALIGN	0x290 /* RMON RX pkts with CRC alignment err */
128#define RMON_R_UNDERSIZE	0x294 /* RMON RX pkts < 64 bytes, good CRC */
129#define RMON_R_OVERSIZE		0x298 /* RMON RX pkts > MAX_FL bytes good CRC */
130#define RMON_R_FRAG		0x29c /* RMON RX pkts < 64 bytes, bad CRC */
131#define RMON_R_JAB		0x2a0 /* RMON RX pkts > MAX_FL bytes, bad CRC */
132#define RMON_R_RESVD_O		0x2a4 /* Reserved */
133#define RMON_R_P64		0x2a8 /* RMON RX 64 byte pkts */
134#define RMON_R_P65TO127		0x2ac /* RMON RX 65 to 127 byte pkts */
135#define RMON_R_P128TO255	0x2b0 /* RMON RX 128 to 255 byte pkts */
136#define RMON_R_P256TO511	0x2b4 /* RMON RX 256 to 511 byte pkts */
137#define RMON_R_P512TO1023	0x2b8 /* RMON RX 512 to 1023 byte pkts */
138#define RMON_R_P1024TO2047	0x2bc /* RMON RX 1024 to 2047 byte pkts */
139#define RMON_R_P_GTE2048	0x2c0 /* RMON RX pkts > 2048 bytes */
140#define RMON_R_OCTETS		0x2c4 /* RMON RX octets */
141#define IEEE_R_DROP		0x2c8 /* Count frames not counted correctly */
142#define IEEE_R_FRAME_OK		0x2cc /* Frames rx'd OK */
143#define IEEE_R_CRC		0x2d0 /* Frames rx'd with CRC err */
144#define IEEE_R_ALIGN		0x2d4 /* Frames rx'd with alignment err */
145#define IEEE_R_MACERR		0x2d8 /* Receive FIFO overflow count */
146#define IEEE_R_FDXFC		0x2dc /* Flow control pause frames rx'd */
147#define IEEE_R_OCTETS_OK	0x2e0 /* Octet cnt for frames rx'd w/o err */
148
149#else
150
151#define FEC_ECNTRL		0x000 /* Ethernet control reg */
152#define FEC_IEVENT		0x004 /* Interrupt even reg */
153#define FEC_IMASK		0x008 /* Interrupt mask reg */
154#define FEC_IVEC		0x00c /* Interrupt vec status reg */
155#define FEC_R_DES_ACTIVE_0	0x010 /* Receive descriptor reg */
156#define FEC_R_DES_ACTIVE_1	FEC_R_DES_ACTIVE_0
157#define FEC_R_DES_ACTIVE_2	FEC_R_DES_ACTIVE_0
158#define FEC_X_DES_ACTIVE_0	0x014 /* Transmit descriptor reg */
159#define FEC_X_DES_ACTIVE_1	FEC_X_DES_ACTIVE_0
160#define FEC_X_DES_ACTIVE_2	FEC_X_DES_ACTIVE_0
161#define FEC_MII_DATA		0x040 /* MII manage frame reg */
162#define FEC_MII_SPEED		0x044 /* MII speed control reg */
163#define FEC_R_BOUND		0x08c /* FIFO receive bound reg */
164#define FEC_R_FSTART		0x090 /* FIFO receive start reg */
165#define FEC_X_WMRK		0x0a4 /* FIFO transmit water mark */
166#define FEC_X_FSTART		0x0ac /* FIFO transmit start reg */
167#define FEC_R_CNTRL		0x104 /* Receive control reg */
168#define FEC_MAX_FRM_LEN		0x108 /* Maximum frame length reg */
169#define FEC_X_CNTRL		0x144 /* Transmit Control reg */
170#define FEC_ADDR_LOW		0x3c0 /* Low 32bits MAC address */
171#define FEC_ADDR_HIGH		0x3c4 /* High 16bits MAC address */
172#define FEC_GRP_HASH_TABLE_HIGH	0x3c8 /* High 32bits hash table */
173#define FEC_GRP_HASH_TABLE_LOW	0x3cc /* Low 32bits hash table */
174#define FEC_R_DES_START_0	0x3d0 /* Receive descriptor ring */
175#define FEC_R_DES_START_1	FEC_R_DES_START_0
176#define FEC_R_DES_START_2	FEC_R_DES_START_0
177#define FEC_X_DES_START_0	0x3d4 /* Transmit descriptor ring */
178#define FEC_X_DES_START_1	FEC_X_DES_START_0
179#define FEC_X_DES_START_2	FEC_X_DES_START_0
180#define FEC_R_BUFF_SIZE_0	0x3d8 /* Maximum receive buff size */
181#define FEC_R_BUFF_SIZE_1	FEC_R_BUFF_SIZE_0
182#define FEC_R_BUFF_SIZE_2	FEC_R_BUFF_SIZE_0
183#define FEC_FIFO_RAM		0x400 /* FIFO RAM buffer */
184/* Not existed in real chip
185 * Just for pass build.
186 */
187#define FEC_RCMR_1		0xfff
188#define FEC_RCMR_2		0xfff
189#define FEC_DMA_CFG_1		0xfff
190#define FEC_DMA_CFG_2		0xfff
191#define FEC_TXIC0		0xfff
192#define FEC_TXIC1		0xfff
193#define FEC_TXIC2		0xfff
194#define FEC_RXIC0		0xfff
195#define FEC_RXIC1		0xfff
196#define FEC_RXIC2		0xfff
197#define FEC_LPI_SLEEP		0xfff
198#define FEC_LPI_WAKE		0xfff
199#endif /* CONFIG_M5272 */
200
201
202/*
203 *	Define the buffer descriptor structure.
204 *
205 *	Evidently, ARM SoCs have the FEC block generated in a
206 *	little endian mode so adjust endianness accordingly.
207 */
208#if defined(CONFIG_ARM) || defined(CONFIG_ARM64)
209#define fec32_to_cpu le32_to_cpu
210#define fec16_to_cpu le16_to_cpu
211#define cpu_to_fec32 cpu_to_le32
212#define cpu_to_fec16 cpu_to_le16
213#define __fec32 __le32
214#define __fec16 __le16
215
216struct bufdesc {
217	__fec16 cbd_datlen;	/* Data length */
218	__fec16 cbd_sc;		/* Control and status info */
219	__fec32 cbd_bufaddr;	/* Buffer address */
220};
221#else
222#define fec32_to_cpu be32_to_cpu
223#define fec16_to_cpu be16_to_cpu
224#define cpu_to_fec32 cpu_to_be32
225#define cpu_to_fec16 cpu_to_be16
226#define __fec32 __be32
227#define __fec16 __be16
228
229struct bufdesc {
230	__fec16	cbd_sc;		/* Control and status info */
231	__fec16	cbd_datlen;	/* Data length */
232	__fec32	cbd_bufaddr;	/* Buffer address */
233};
234#endif
235
236struct bufdesc_ex {
237	struct bufdesc desc;
238	__fec32 cbd_esc;
239	__fec32 cbd_prot;
240	__fec32 cbd_bdu;
241	__fec32 ts;
242	__fec16 res0[4];
243};
244
245/*
246 *	The following definitions courtesy of commproc.h, which where
247 *	Copyright (c) 1997 Dan Malek (dmalek@jlc.net).
248 */
249#define BD_SC_EMPTY	((ushort)0x8000)	/* Receive is empty */
250#define BD_SC_READY	((ushort)0x8000)	/* Transmit is ready */
251#define BD_SC_WRAP	((ushort)0x2000)	/* Last buffer descriptor */
252#define BD_SC_INTRPT	((ushort)0x1000)	/* Interrupt on change */
253#define BD_SC_CM	((ushort)0x0200)	/* Continuous mode */
254#define BD_SC_ID	((ushort)0x0100)	/* Rec'd too many idles */
255#define BD_SC_P		((ushort)0x0100)	/* xmt preamble */
256#define BD_SC_BR	((ushort)0x0020)	/* Break received */
257#define BD_SC_FR	((ushort)0x0010)	/* Framing error */
258#define BD_SC_PR	((ushort)0x0008)	/* Parity error */
259#define BD_SC_OV	((ushort)0x0002)	/* Overrun */
260#define BD_SC_CD	((ushort)0x0001)	/* ?? */
261
262/* Buffer descriptor control/status used by Ethernet receive.
263 */
264#define BD_ENET_RX_EMPTY	((ushort)0x8000)
265#define BD_ENET_RX_WRAP		((ushort)0x2000)
266#define BD_ENET_RX_INTR		((ushort)0x1000)
267#define BD_ENET_RX_LAST		((ushort)0x0800)
268#define BD_ENET_RX_FIRST	((ushort)0x0400)
269#define BD_ENET_RX_MISS		((ushort)0x0100)
270#define BD_ENET_RX_LG		((ushort)0x0020)
271#define BD_ENET_RX_NO		((ushort)0x0010)
272#define BD_ENET_RX_SH		((ushort)0x0008)
273#define BD_ENET_RX_CR		((ushort)0x0004)
274#define BD_ENET_RX_OV		((ushort)0x0002)
275#define BD_ENET_RX_CL		((ushort)0x0001)
276#define BD_ENET_RX_STATS	((ushort)0x013f)	/* All status bits */
277
278/* Enhanced buffer descriptor control/status used by Ethernet receive */
279#define BD_ENET_RX_VLAN		0x00000004
280
281/* Buffer descriptor control/status used by Ethernet transmit.
282 */
283#define BD_ENET_TX_READY	((ushort)0x8000)
284#define BD_ENET_TX_PAD		((ushort)0x4000)
285#define BD_ENET_TX_WRAP		((ushort)0x2000)
286#define BD_ENET_TX_INTR		((ushort)0x1000)
287#define BD_ENET_TX_LAST		((ushort)0x0800)
288#define BD_ENET_TX_TC		((ushort)0x0400)
289#define BD_ENET_TX_DEF		((ushort)0x0200)
290#define BD_ENET_TX_HB		((ushort)0x0100)
291#define BD_ENET_TX_LC		((ushort)0x0080)
292#define BD_ENET_TX_RL		((ushort)0x0040)
293#define BD_ENET_TX_RCMASK	((ushort)0x003c)
294#define BD_ENET_TX_UN		((ushort)0x0002)
295#define BD_ENET_TX_CSL		((ushort)0x0001)
296#define BD_ENET_TX_STATS	((ushort)0x0fff)	/* All status bits */
297
298/* enhanced buffer descriptor control/status used by Ethernet transmit */
299#define BD_ENET_TX_INT		0x40000000
300#define BD_ENET_TX_TS		0x20000000
301#define BD_ENET_TX_PINS		0x10000000
302#define BD_ENET_TX_IINS		0x08000000
303
304
305/* This device has up to three irqs on some platforms */
306#define FEC_IRQ_NUM		3
307
308/* Maximum number of queues supported
309 * ENET with AVB IP can support up to 3 independent tx queues and rx queues.
310 * User can point the queue number that is less than or equal to 3.
311 */
312#define FEC_ENET_MAX_TX_QS	3
313#define FEC_ENET_MAX_RX_QS	3
314
315#define FEC_R_DES_START(X)	(((X) == 1) ? FEC_R_DES_START_1 : \
316				(((X) == 2) ? \
317					FEC_R_DES_START_2 : FEC_R_DES_START_0))
318#define FEC_X_DES_START(X)	(((X) == 1) ? FEC_X_DES_START_1 : \
319				(((X) == 2) ? \
320					FEC_X_DES_START_2 : FEC_X_DES_START_0))
321#define FEC_R_BUFF_SIZE(X)	(((X) == 1) ? FEC_R_BUFF_SIZE_1 : \
322				(((X) == 2) ? \
323					FEC_R_BUFF_SIZE_2 : FEC_R_BUFF_SIZE_0))
324
325#define FEC_DMA_CFG(X)		(((X) == 2) ? FEC_DMA_CFG_2 : FEC_DMA_CFG_1)
326
327#define DMA_CLASS_EN		(1 << 16)
328#define FEC_RCMR(X)		(((X) == 2) ? FEC_RCMR_2 : FEC_RCMR_1)
329#define IDLE_SLOPE_MASK		0xffff
330#define IDLE_SLOPE_1		0x200 /* BW fraction: 0.5 */
331#define IDLE_SLOPE_2		0x200 /* BW fraction: 0.5 */
332#define IDLE_SLOPE(X)		(((X) == 1) ?				\
333				(IDLE_SLOPE_1 & IDLE_SLOPE_MASK) :	\
334				(IDLE_SLOPE_2 & IDLE_SLOPE_MASK))
335#define RCMR_MATCHEN		(0x1 << 16)
336#define RCMR_CMP_CFG(v, n)	(((v) & 0x7) <<  (n << 2))
337#define RCMR_CMP_1		(RCMR_CMP_CFG(0, 0) | RCMR_CMP_CFG(1, 1) | \
338				RCMR_CMP_CFG(2, 2) | RCMR_CMP_CFG(3, 3))
339#define RCMR_CMP_2		(RCMR_CMP_CFG(4, 0) | RCMR_CMP_CFG(5, 1) | \
340				RCMR_CMP_CFG(6, 2) | RCMR_CMP_CFG(7, 3))
341#define RCMR_CMP(X)		(((X) == 1) ? RCMR_CMP_1 : RCMR_CMP_2)
342#define FEC_TX_BD_FTYPE(X)	(((X) & 0xf) << 20)
343
344/* The number of Tx and Rx buffers.  These are allocated from the page
345 * pool.  The code may assume these are power of two, so it it best
346 * to keep them that size.
347 * We don't need to allocate pages for the transmitter.  We just use
348 * the skbuffer directly.
349 */
350
351#define FEC_ENET_XDP_HEADROOM	(XDP_PACKET_HEADROOM)
352#define FEC_ENET_RX_PAGES	256
353#define FEC_ENET_RX_FRSIZE	(PAGE_SIZE - FEC_ENET_XDP_HEADROOM \
354		- SKB_DATA_ALIGN(sizeof(struct skb_shared_info)))
355#define FEC_ENET_RX_FRPPG	(PAGE_SIZE / FEC_ENET_RX_FRSIZE)
356#define RX_RING_SIZE		(FEC_ENET_RX_FRPPG * FEC_ENET_RX_PAGES)
357#define FEC_ENET_TX_FRSIZE	2048
358#define FEC_ENET_TX_FRPPG	(PAGE_SIZE / FEC_ENET_TX_FRSIZE)
359#define TX_RING_SIZE		1024	/* Must be power of two */
360#define TX_RING_MOD_MASK	511	/*   for this to work */
361
362#define BD_ENET_RX_INT		0x00800000
363#define BD_ENET_RX_PTP		((ushort)0x0400)
364#define BD_ENET_RX_ICE		0x00000020
365#define BD_ENET_RX_PCR		0x00000010
366#define FLAG_RX_CSUM_ENABLED	(BD_ENET_RX_ICE | BD_ENET_RX_PCR)
367#define FLAG_RX_CSUM_ERROR	(BD_ENET_RX_ICE | BD_ENET_RX_PCR)
368
369/* Interrupt events/masks. */
370#define FEC_ENET_HBERR  ((uint)0x80000000)      /* Heartbeat error */
371#define FEC_ENET_BABR   ((uint)0x40000000)      /* Babbling receiver */
372#define FEC_ENET_BABT   ((uint)0x20000000)      /* Babbling transmitter */
373#define FEC_ENET_GRA    ((uint)0x10000000)      /* Graceful stop complete */
374#define FEC_ENET_TXF_0	((uint)0x08000000)	/* Full frame transmitted */
375#define FEC_ENET_TXF_1	((uint)0x00000008)	/* Full frame transmitted */
376#define FEC_ENET_TXF_2	((uint)0x00000080)	/* Full frame transmitted */
377#define FEC_ENET_TXB    ((uint)0x04000000)      /* A buffer was transmitted */
378#define FEC_ENET_RXF_0	((uint)0x02000000)	/* Full frame received */
379#define FEC_ENET_RXF_1	((uint)0x00000002)	/* Full frame received */
380#define FEC_ENET_RXF_2	((uint)0x00000020)	/* Full frame received */
381#define FEC_ENET_RXB    ((uint)0x01000000)      /* A buffer was received */
382#define FEC_ENET_MII    ((uint)0x00800000)      /* MII interrupt */
383#define FEC_ENET_EBERR  ((uint)0x00400000)      /* SDMA bus error */
384#define FEC_ENET_WAKEUP	((uint)0x00020000)	/* Wakeup request */
385#define FEC_ENET_TXF	(FEC_ENET_TXF_0 | FEC_ENET_TXF_1 | FEC_ENET_TXF_2)
386#define FEC_ENET_RXF	(FEC_ENET_RXF_0 | FEC_ENET_RXF_1 | FEC_ENET_RXF_2)
387#define FEC_ENET_RXF_GET(X)	(((X) == 0) ? FEC_ENET_RXF_0 :	\
388				(((X) == 1) ? FEC_ENET_RXF_1 :	\
389				FEC_ENET_RXF_2))
390#define FEC_ENET_TS_AVAIL       ((uint)0x00010000)
391#define FEC_ENET_TS_TIMER       ((uint)0x00008000)
392
393#define FEC_DEFAULT_IMASK (FEC_ENET_TXF | FEC_ENET_RXF)
394#define FEC_RX_DISABLED_IMASK (FEC_DEFAULT_IMASK & (~FEC_ENET_RXF))
395
396#define FEC_ENET_TXC_DLY	((uint)0x00010000)
397#define FEC_ENET_RXC_DLY	((uint)0x00020000)
398
399/* ENET interrupt coalescing macro define */
400#define FEC_ITR_CLK_SEL		(0x1 << 30)
401#define FEC_ITR_EN		(0x1 << 31)
402#define FEC_ITR_ICFT(X)		(((X) & 0xff) << 20)
403#define FEC_ITR_ICTT(X)		((X) & 0xffff)
404#define FEC_ITR_ICFT_DEFAULT	200  /* Set 200 frame count threshold */
405#define FEC_ITR_ICTT_DEFAULT	1000 /* Set 1000us timer threshold */
406
407#define FEC_VLAN_TAG_LEN	0x04
408#define FEC_ETHTYPE_LEN		0x02
409
410/* Controller is ENET-MAC */
411#define FEC_QUIRK_ENET_MAC		(1 << 0)
412/* Controller needs driver to swap frame */
413#define FEC_QUIRK_SWAP_FRAME		(1 << 1)
414/* Controller uses gasket */
415#define FEC_QUIRK_USE_GASKET		(1 << 2)
416/* Controller has GBIT support */
417#define FEC_QUIRK_HAS_GBIT		(1 << 3)
418/* Controller has extend desc buffer */
419#define FEC_QUIRK_HAS_BUFDESC_EX	(1 << 4)
420/* Controller has hardware checksum support */
421#define FEC_QUIRK_HAS_CSUM		(1 << 5)
422/* Controller has hardware vlan support */
423#define FEC_QUIRK_HAS_VLAN		(1 << 6)
424/* ENET IP errata ERR006358
425 *
426 * If the ready bit in the transmit buffer descriptor (TxBD[R]) is previously
427 * detected as not set during a prior frame transmission, then the
428 * ENET_TDAR[TDAR] bit is cleared at a later time, even if additional TxBDs
429 * were added to the ring and the ENET_TDAR[TDAR] bit is set. This results in
430 * frames not being transmitted until there is a 0-to-1 transition on
431 * ENET_TDAR[TDAR].
432 */
433#define FEC_QUIRK_ERR006358		(1 << 7)
434/* ENET IP hw AVB
435 *
436 * i.MX6SX ENET IP add Audio Video Bridging (AVB) feature support.
437 * - Two class indicators on receive with configurable priority
438 * - Two class indicators and line speed timer on transmit allowing
439 *   implementation class credit based shapers externally
440 * - Additional DMA registers provisioned to allow managing up to 3
441 *   independent rings
442 */
443#define FEC_QUIRK_HAS_AVB		(1 << 8)
444/* There is a TDAR race condition for mutliQ when the software sets TDAR
445 * and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
446 * This will cause the udma_tx and udma_tx_arbiter state machines to hang.
447 * The issue exist at i.MX6SX enet IP.
448 */
449#define FEC_QUIRK_ERR007885		(1 << 9)
450/* ENET Block Guide/ Chapter for the iMX6SX (PELE) address one issue:
451 * After set ENET_ATCR[Capture], there need some time cycles before the counter
452 * value is capture in the register clock domain.
453 * The wait-time-cycles is at least 6 clock cycles of the slower clock between
454 * the register clock and the 1588 clock. The 1588 ts_clk is fixed to 25Mhz,
455 * register clock is 66Mhz, so the wait-time-cycles must be greater than 240ns
456 * (40ns * 6).
457 */
458#define FEC_QUIRK_BUG_CAPTURE		(1 << 10)
459/* Controller has only one MDIO bus */
460#define FEC_QUIRK_SINGLE_MDIO		(1 << 11)
461/* Controller supports RACC register */
462#define FEC_QUIRK_HAS_RACC		(1 << 12)
463/* Controller supports interrupt coalesc */
464#define FEC_QUIRK_HAS_COALESCE		(1 << 13)
465/* Interrupt doesn't wake CPU from deep idle */
466#define FEC_QUIRK_ERR006687		(1 << 14)
467/* The MIB counters should be cleared and enabled during
468 * initialisation.
469 */
470#define FEC_QUIRK_MIB_CLEAR		(1 << 15)
471/* Only i.MX25/i.MX27/i.MX28 controller supports FRBR,FRSR registers,
472 * those FIFO receive registers are resolved in other platforms.
473 */
474#define FEC_QUIRK_HAS_FRREG		(1 << 16)
475
476/* Some FEC hardware blocks need the MMFR cleared at setup time to avoid
477 * the generation of an MII event. This must be avoided in the older
478 * FEC blocks where it will stop MII events being generated.
479 */
480#define FEC_QUIRK_CLEAR_SETUP_MII	(1 << 17)
481
482/* Some link partners do not tolerate the momentary reset of the REF_CLK
483 * frequency when the RNCTL register is cleared by hardware reset.
484 */
485#define FEC_QUIRK_NO_HARD_RESET		(1 << 18)
486
487/* i.MX6SX ENET IP supports multiple queues (3 queues), use this quirk to
488 * represents this ENET IP.
489 */
490#define FEC_QUIRK_HAS_MULTI_QUEUES	(1 << 19)
491
492/* i.MX8MQ ENET IP version add new feature to support IEEE 802.3az EEE
493 * standard. For the transmission, MAC supply two user registers to set
494 * Sleep (TS) and Wake (TW) time.
495 */
496#define FEC_QUIRK_HAS_EEE		(1 << 20)
497
498/* i.MX8QM ENET IP version add new feture to generate delayed TXC/RXC
499 * as an alternative option to make sure it works well with various PHYs.
500 * For the implementation of delayed clock, ENET takes synchronized 250MHz
501 * clocks to generate 2ns delay.
502 */
503#define FEC_QUIRK_DELAYED_CLKS_SUPPORT	(1 << 21)
504
505/* i.MX8MQ SoC integration mix wakeup interrupt signal into "int2" interrupt line. */
506#define FEC_QUIRK_WAKEUP_FROM_INT2	(1 << 22)
507
508/* i.MX6Q adds pm_qos support */
509#define FEC_QUIRK_HAS_PMQOS			BIT(23)
510
511/* Not all FEC hardware block MDIOs support accesses in C45 mode.
512 * Older blocks in the ColdFire parts do not support it.
513 */
514#define FEC_QUIRK_HAS_MDIO_C45		BIT(24)
515
516struct bufdesc_prop {
517	int qid;
518	/* Address of Rx and Tx buffers */
519	struct bufdesc	*base;
520	struct bufdesc	*last;
521	struct bufdesc	*cur;
522	void __iomem	*reg_desc_active;
523	dma_addr_t	dma;
524	unsigned short ring_size;
525	unsigned char dsize;
526	unsigned char dsize_log2;
527};
528
529struct fec_enet_priv_txrx_info {
530	int	offset;
531	struct	page *page;
532	struct  sk_buff *skb;
533};
534
535enum {
536	RX_XDP_REDIRECT = 0,
537	RX_XDP_PASS,
538	RX_XDP_DROP,
539	RX_XDP_TX,
540	RX_XDP_TX_ERRORS,
541	TX_XDP_XMIT,
542	TX_XDP_XMIT_ERRORS,
543
544	/* The following must be the last one */
545	XDP_STATS_TOTAL,
546};
547
548enum fec_txbuf_type {
549	FEC_TXBUF_T_SKB,
550	FEC_TXBUF_T_XDP_NDO,
551	FEC_TXBUF_T_XDP_TX,
552};
553
554struct fec_tx_buffer {
555	void *buf_p;
556	enum fec_txbuf_type type;
557};
558
559struct fec_enet_priv_tx_q {
560	struct bufdesc_prop bd;
561	unsigned char *tx_bounce[TX_RING_SIZE];
562	struct fec_tx_buffer tx_buf[TX_RING_SIZE];
563
564	unsigned short tx_stop_threshold;
565	unsigned short tx_wake_threshold;
566
567	struct bufdesc	*dirty_tx;
568	char *tso_hdrs;
569	dma_addr_t tso_hdrs_dma;
570};
571
572struct fec_enet_priv_rx_q {
573	struct bufdesc_prop bd;
574	struct  fec_enet_priv_txrx_info rx_skb_info[RX_RING_SIZE];
575
576	/* page_pool */
577	struct page_pool *page_pool;
578	struct xdp_rxq_info xdp_rxq;
579	u32 stats[XDP_STATS_TOTAL];
580
581	/* rx queue number, in the range 0-7 */
582	u8 id;
583};
584
585struct fec_stop_mode_gpr {
586	struct regmap *gpr;
587	u8 reg;
588	u8 bit;
589};
590
591/* The FEC buffer descriptors track the ring buffers.  The rx_bd_base and
592 * tx_bd_base always point to the base of the buffer descriptors.  The
593 * cur_rx and cur_tx point to the currently available buffer.
594 * The dirty_tx tracks the current buffer that is being sent by the
595 * controller.  The cur_tx and dirty_tx are equal under both completely
596 * empty and completely full conditions.  The empty/ready indicator in
597 * the buffer descriptor determines the actual condition.
598 */
599struct fec_enet_private {
600	/* Hardware registers of the FEC device */
601	void __iomem *hwp;
602
603	struct net_device *netdev;
604
605	struct clk *clk_ipg;
606	struct clk *clk_ahb;
607	struct clk *clk_ref;
608	struct clk *clk_enet_out;
609	struct clk *clk_ptp;
610	struct clk *clk_2x_txclk;
611
612	bool ptp_clk_on;
613	struct mutex ptp_clk_mutex;
614	unsigned int num_tx_queues;
615	unsigned int num_rx_queues;
616
617	/* The saved address of a sent-in-place packet/buffer, for skfree(). */
618	struct fec_enet_priv_tx_q *tx_queue[FEC_ENET_MAX_TX_QS];
619	struct fec_enet_priv_rx_q *rx_queue[FEC_ENET_MAX_RX_QS];
620
621	unsigned int total_tx_ring_size;
622	unsigned int total_rx_ring_size;
623
624	struct	platform_device *pdev;
625
626	int	dev_id;
627
628	/* Phylib and MDIO interface */
629	struct	mii_bus *mii_bus;
630	uint	phy_speed;
631	phy_interface_t	phy_interface;
632	struct device_node *phy_node;
633	bool	rgmii_txc_dly;
634	bool	rgmii_rxc_dly;
635	bool	rpm_active;
636	int	link;
637	int	full_duplex;
638	int	speed;
639	int	irq[FEC_IRQ_NUM];
640	bool	bufdesc_ex;
641	int	pause_flag;
642	int	wol_flag;
643	int	wake_irq;
644	u32	quirks;
645
646	struct	napi_struct napi;
647	int	csum_flags;
648
649	struct work_struct tx_timeout_work;
650
651	struct ptp_clock *ptp_clock;
652	struct ptp_clock_info ptp_caps;
653	spinlock_t tmreg_lock;
654	struct cyclecounter cc;
655	struct timecounter tc;
656	u32 cycle_speed;
657	int hwts_rx_en;
658	int hwts_tx_en;
659	struct delayed_work time_keep;
660	struct regulator *reg_phy;
661	struct fec_stop_mode_gpr stop_gpr;
662	struct pm_qos_request pm_qos_req;
663
664	unsigned int tx_align;
665	unsigned int rx_align;
666
667	/* hw interrupt coalesce */
668	unsigned int rx_pkts_itr;
669	unsigned int rx_time_itr;
670	unsigned int tx_pkts_itr;
671	unsigned int tx_time_itr;
672	unsigned int itr_clk_rate;
673
674	/* tx lpi eee mode */
675	struct ethtool_keee eee;
676	unsigned int clk_ref_rate;
677
678	/* ptp clock period in ns*/
679	unsigned int ptp_inc;
680
681	/* pps  */
682	int pps_channel;
683	unsigned int reload_period;
684	int pps_enable;
685	unsigned int next_counter;
686	struct hrtimer perout_timer;
687	u64 perout_stime;
688
689	struct imx_sc_ipc *ipc_handle;
690
691	/* XDP BPF Program */
692	struct bpf_prog *xdp_prog;
693
694	u64 ethtool_stats[];
695};
696
697void fec_ptp_init(struct platform_device *pdev, int irq_idx);
698void fec_ptp_stop(struct platform_device *pdev);
699void fec_ptp_start_cyclecounter(struct net_device *ndev);
700int fec_ptp_set(struct net_device *ndev, struct kernel_hwtstamp_config *config,
701		struct netlink_ext_ack *extack);
702void fec_ptp_get(struct net_device *ndev, struct kernel_hwtstamp_config *config);
703
704/****************************************************************************/
705#endif /* FEC_H */
706