ethtool: replace struct ethtool_eee with a new struct ethtool_keee on kernel side

In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: improve XDP_TX performance

As suggested by Jesper and Alexander, we can avoid converting xdp_buff
to xdp_frame in case of XDP_TX to save a bunch of CPU cycles, so that
we can further improve the XDP_TX performance.

Before this patch on i.MX8MP-EVK board, the performance shows as follows.
root@imx8mpevk:~# ./xdp2 eth0
proto 17: 353918 pkt/s
proto 17: 352923 pkt/s
proto 17: 353900 pkt/s
proto 17: 352672 pkt/s
proto 17: 353912 pkt/s
proto 17: 354219 pkt/s

After applying this patch, the performance is improved.
root@imx8mpevk:~# ./xdp2 eth0
proto 17: 369261 pkt/s
proto 17: 369267 pkt/s
proto 17: 369206 pkt/s
proto 17: 369214 pkt/s
proto 17: 369126 pkt/s
proto 17: 369272 pkt/s

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Suggested-by: Jesper Dangaard Brouer <hawk@kernel.org>
Reviewed-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add XDP_TX feature support

The XDP_TX feature is not supported before, and all the frames
which are deemed to do XDP_TX action actually do the XDP_DROP
action. So this patch adds the XDP_TX support to FEC driver.

I tested the performance of XDP_TX in XDP_DRV mode and XDP_SKB
mode respectively on i.MX8MP-EVK platform, and as suggested by
Jesper, I also tested the performance of XDP_REDIRECT on the
same platform. And the test steps and results are as follows.

XDP_TX test:
Step 1: One board is used as generator and connects to switch,and
the FEC port of DUT also connects to the switch. Both boards with
flow control off. Then the generator runs the
pktgen_sample03_burst_single_flow.sh script to generate and send
burst traffic to DUT. Note that the size of packet was set to 64
bytes and the procotol of packet was UDP in my test scenario. In
addition, the SMAC of the packet need to be different from the MAC
of the generator, because the xdp2 program will swap the DMAC and
SMAC of the packet and send it back to the generator. If the SMAC
of the generated packet is the MAC of the generator, the generator
will receive the returned traffic which increase the CPU loading
and significantly degrade the transmit speed of the generator, and
finally it affects the test of XDP_TX performance.

Step 2: The DUT runs the xdp2 program to transmit received UDP
packets back out on the same port where they were received.

root@imx8mpevk:~# ./xdp2 eth0
proto 17: 353918 pkt/s
proto 17: 352923 pkt/s
proto 17: 353900 pkt/s
proto 17: 352672 pkt/s
proto 17: 353912 pkt/s
proto 17: 354219 pkt/s

root@imx8mpevk:~# ./xdp2 -S eth0
proto 17: 160604 pkt/s
proto 17: 160708 pkt/s
proto 17: 160564 pkt/s
proto 17: 160684 pkt/s
proto 17: 160640 pkt/s
proto 17: 160720 pkt/s

The above results show that the XDP_TX performance of XDP_DRV mode
is much better than XDP_SKB mode, more than twice that of XDP_SKB
mode, which is in line with our expectation.

XDP_REDIRECT test:
Step1: Both the generator and the FEC port of the DUT connet to the
switch port. All the ports with flow control off, then the generator
runs the pktgen script to generate and send burst traffic to DUT.
Note that the size of packet was set to 64 bytes and the procotol of
packet was UDP in my test scenario.

Step2: The DUT runs the xdp_redirect program to redirect the traffic
from the FEC port to the FEC port itself.

root@imx8mpevk:~# ./xdp_redirect eth0 eth0
Redirecting from eth0 (ifindex 2; driver fec) to eth0
(ifindex 2; driver fec)
Summary 232,302 rx/s 0 err,drop/s 232,344 xmit/s
Summary 234,579 rx/s 0 err,drop/s 234,577 xmit/s
Summary 235,548 rx/s 0 err,drop/s 235,549 xmit/s
Summary 234,704 rx/s 0 err,drop/s 234,703 xmit/s
Summary 235,504 rx/s 0 err,drop/s 235,504 xmit/s
Summary 235,223 rx/s 0 err,drop/s 235,224 xmit/s
Summary 234,509 rx/s 0 err,drop/s 234,507 xmit/s
Summary 235,481 rx/s 0 err,drop/s 235,482 xmit/s
Summary 234,684 rx/s 0 err,drop/s 234,683 xmit/s
Summary 235,520 rx/s 0 err,drop/s 235,520 xmit/s
Summary 235,461 rx/s 0 err,drop/s 235,461 xmit/s
Summary 234,627 rx/s 0 err,drop/s 234,627 xmit/s
Summary 235,611 rx/s 0 err,drop/s 235,611 xmit/s
Packets received : 3,053,753
Average packets/s : 234,904
Packets transmitted : 3,053,792
Average transmit/s : 234,907

Compared the performance of XDP_TX with XDP_REDIRECT, XDP_TX is also
much better than XDP_REDIRECT. It's also in line with our expectation.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Jesper Dangaard Brouer <hawk@kernel.org>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

eth: add missing xdp.h includes in drivers

Handful of drivers currently expect to get xdp.h by virtue
of including netdevice.h. This will soon no longer be the case
so add explicit includes.

Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230803010230.1755386-2-kuba@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>

net: fec: delete fec_ptp_disable_hwts()

Commit 340746398b67 ("net: fec: fix hardware time stamping by external
devices") was overly cautious with calling fec_ptp_disable_hwts() when
cmd == SIOCSHWTSTAMP and use_fec_hwts == false, because use_fec_hwts is
based on a runtime invariant (phy_has_hwtstamp()). Thus, if use_fec_hwts
is false, then fep->hwts_tx_en and fep->hwts_rx_en cannot be changed at
runtime; their values depend on the initial memory allocation, which
already sets them to zeroes.

If the core will ever gain support for switching timestamping layers,
it will arrange for a more organized calling convention and disable
timestamping in the previous layer as a first step. This means that the
code in the FEC driver is not necessary in any case.

The purpose of this change is to arrange the phy_has_hwtstamp() code in
a way in which it can be refactored away into generic logic.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20230801142824.1772134-8-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec: convert to ndo_hwtstamp_get() and ndo_hwtstamp_set()

The hardware timestamping through ndo_eth_ioctl() is going away.
Convert the FEC driver to the new API before that can be removed.

After removing the timestamping logic from fec_enet_ioctl(), the rest
is equivalent to phy_do_ioctl_running().

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20230801142824.1772134-7-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec: remove unused members from struct fec_enet_private

Three members of struct fec_enet_private have not been used since
they were first introduced into the FEC driver (commit 6605b730c061
("FEC: Add time stamping code and a PTP hardware clock")). Namely,
last_overflow_check, rx_hwtstamp_filter and base_incval. These
unused members make the struct fec_enet_private a bit messy and
might confuse the readers. There is no reason to keep them in the
FEC driver any longer.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20230718090928.2654347-4-wei.fang@nxp.com
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec: remove the remaining code of rx copybreak

Since the commit 95698ff6177b ("net: fec: using page pool to manage
RX buffers") has been applied, all the rx packets, no matter small
packets or large packets are put directly into the kernel networking
buffers. That is to say, the rx copybreak function has been removed
since then, but the related code has not been completely cleaned up.
So the purpose of this patch is to clean up the remaining related
code of rx copybreak.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20230718090928.2654347-2-wei.fang@nxp.com
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec: increase the size of tx ring and update tx_wake_threshold

When the XDP feature is enabled and with heavy XDP frames to be
transmitted, there is a considerable probability that available
tx BDs are insufficient. This will lead to some XDP frames to be
discarded and the "NOT enough BD for SG!" error log will appear
in the console (as shown below).

[ 160.013112] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.023116] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.028926] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.038946] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.044758] fec 30be0000.ethernet eth0: NOT enough BD for SG!

In the case of heavy XDP traffic, sometimes the speed of recycling
tx BDs may be slower than the speed of sending XDP frames. There
may be several specific reasons, such as the interrupt is not
responsed in time, the efficiency of the NAPI callback function is
too low due to all the queues (tx queues and rx queues) share the
same NAPI, and so on.

After trying various methods, I think that increase the size of tx
BD ring is simple and effective. Maybe the best resolution is that
allocate NAPI for each queue to improve the efficiency of the NAPI
callback, but this change is a bit big and I didn't try this method.
Perheps this method will be implemented in a future patch.

This patch also updates the tx_wake_threshold of tx ring which is
related to the size of tx ring in the previous logic. Otherwise,
the tx_wake_threshold will be too high (403 BDs), which is more
likely to impact the slow path in the case of heavy XDP traffic,
because XDP path and slow path share the tx BD rings. According
to Jakub's suggestion, the tx_wake_threshold is at least equal to
tx_stop_threshold + 2 * MAX_SKB_FRAGS, if a queue of hundreds of
entries is overflowing, we should be able to apply a hysteresis
of a few tens of entries.

Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: fec: recycle pages for transmitted XDP frames

Once the XDP frames have been successfully transmitted through the
ndo_xdp_xmit() interface, it's the driver responsibility to free
the frames so that the page_pool can recycle the pages and reuse
them. However, this action is not implemented in the fec driver.
This leads to a user-visible problem that the console will print
the following warning log.

[ 157.568851] page_pool_release_retry() stalled pool shutdown 1389 inflight 60 sec
[ 217.983446] page_pool_release_retry() stalled pool shutdown 1389 inflight 120 sec
[ 278.399006] page_pool_release_retry() stalled pool shutdown 1389 inflight 181 sec
[ 338.812885] page_pool_release_retry() stalled pool shutdown 1389 inflight 241 sec
[ 399.226946] page_pool_release_retry() stalled pool shutdown 1389 inflight 302 sec

Therefore, to solve this issue, we free XDP frames via xdp_return_frame()
while cleaning the tx BD ring.

Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: fec: make use of MDIO C45 quirk

Not all fec MDIO bus drivers support C45 mode transactions. The older fec
hardware block in many ColdFire SoCs does not appear to support them, at
least according to most of the different ColdFire SoC reference manuals.
The bits used to generate C45 access on the iMX parts, in the OP field
of the MMFR register, are documented as generating non-compliant MII
frames (it is not documented as to exactly how they are non-compliant).

Commit 8d03ad1ab0b0 ("net: fec: Separate C22 and C45 transactions")
means the fec driver will always register c45 MDIO read and write
methods. During probe these will always be accessed now generating
non-compliant MII accesses on ColdFire based devices.

Add a quirk define, FEC_QUIRK_HAS_MDIO_C45, that can be used to
distinguish silicon that supports MDIO C45 framing or not. Add this to
all the existing iMX quirks, so they will be behave as they do now (*).

(*) it seems that some iMX parts may not support C45 transactions either.
The iMX25 and iMX50 Reference Manuals contain similar wording to
the ColdFire Reference Manuals on this.

Fixes: 8d03ad1ab0b0 ("net: fec: Separate C22 and C45 transactions")
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230404052207.3064861-1-gerg@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec: add xdp and page pool statistics

Added xdp and page pool statistics.
In order to make the implementation simple and compatible, the patch
uses the 32bit integer to record the XDP statistics.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add initial XDP support

This patch adds the initial XDP support to Freescale driver. It supports
XDP_PASS, XDP_DROP and XDP_REDIRECT actions. Upcoming patches will add
support for XDP_TX and Zero Copy features.

As the patch is rather large, the part of codes to collect the
statistics is separated and will prepare a dedicated patch for that
part.

I just tested with the application of xdpsock.
-- Native here means running command of "xdpsock -i eth0"
-- SKB-Mode means running command of "xdpsock -S -i eth0"

The following are the testing result relating to XDP mode:

root@imx8qxpc0mek:~/bpf# ./xdpsock -i eth0
sock0@eth0:0 rxdrop xdp-drv
pps pkts 1.00
rx 371347 2717794
tx 0 0

root@imx8qxpc0mek:~/bpf# ./xdpsock -S -i eth0
sock0@eth0:0 rxdrop xdp-skb
pps pkts 1.00
rx 202229 404528
tx 0 0

root@imx8qxpc0mek:~/bpf# ./xdp2 eth0
proto 0: 496708 pkt/s
proto 0: 505469 pkt/s
proto 0: 505283 pkt/s
proto 0: 505443 pkt/s
proto 0: 505465 pkt/s

root@imx8qxpc0mek:~/bpf# ./xdp2 -S eth0
proto 0: 0 pkt/s
proto 17: 118778 pkt/s
proto 17: 118989 pkt/s
proto 0: 1 pkt/s
proto 17: 118987 pkt/s
proto 0: 0 pkt/s
proto 17: 118943 pkt/s
proto 17: 118976 pkt/s
proto 0: 1 pkt/s
proto 17: 119006 pkt/s
proto 0: 0 pkt/s
proto 17: 119071 pkt/s
proto 17: 119092 pkt/s

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20221031185350.2045675-1-shenwei.wang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: fec: Add support for periodic output signal of PPS

This patch adds the support for configuring periodic output
signal of PPS. So the PPS can be output at a specified time
and period.
For developers or testers, they can use the command "echo
<channel> <start.sec> <start.nsec> <period.sec> <period.
nsec> > /sys/class/ptp/ptp0/period" to specify time and
period to output PPS signal.
Notice that, the channel can only be set to 0. In addtion,
the start time must larger than the current PTP clock time.
So users can use the command "phc_ctl /dev/ptp0 -- get" to
get the current PTP clock time before.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: using page pool to manage RX buffers

This patch optimizes the RX buffer management by using the page
pool. The purpose for this change is to prepare for the following
XDP support. The current driver uses one frame per page for easy
management.

Added __maybe_unused attribute to the following functions to avoid
the compiling warning. Those functions will be removed by a separate
patch once this page pool solution is accepted.
- fec_enet_new_rxbdp
- fec_enet_copybreak

The following are the comparing result between page pool implementation
and the original implementation (non page pool).

--- small packet (64 bytes) testing are almost the same
--- no matter what the implementation is
--- on both i.MX8 and i.MX6SX platforms.

shenwei@5810:~/pktgen$ iperf -c 10.81.16.245 -w 2m -i 1 -l 64
------------------------------------------------------------
Client connecting to 10.81.16.245, TCP port 5001
TCP window size: 416 KByte (WARNING: requested 1.91 MByte)
------------------------------------------------------------
[ 1] local 10.81.17.20 port 39728 connected with 10.81.16.245 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.0000-1.0000 sec 37.0 MBytes 311 Mbits/sec
[ 1] 1.0000-2.0000 sec 36.6 MBytes 307 Mbits/sec
[ 1] 2.0000-3.0000 sec 37.2 MBytes 312 Mbits/sec
[ 1] 3.0000-4.0000 sec 37.1 MBytes 312 Mbits/sec
[ 1] 4.0000-5.0000 sec 37.2 MBytes 312 Mbits/sec
[ 1] 5.0000-6.0000 sec 37.2 MBytes 312 Mbits/sec
[ 1] 6.0000-7.0000 sec 37.2 MBytes 312 Mbits/sec
[ 1] 7.0000-8.0000 sec 37.2 MBytes 312 Mbits/sec
[ 1] 0.0000-8.0943 sec 299 MBytes 310 Mbits/sec

--- Page Pool implementation on i.MX8 ----

shenwei@5810:~$ iperf -c 10.81.16.245 -w 2m -i 1
------------------------------------------------------------
Client connecting to 10.81.16.245, TCP port 5001
TCP window size: 416 KByte (WARNING: requested 1.91 MByte)
------------------------------------------------------------
[ 1] local 10.81.17.20 port 43204 connected with 10.81.16.245 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.0000-1.0000 sec 111 MBytes 933 Mbits/sec
[ 1] 1.0000-2.0000 sec 111 MBytes 934 Mbits/sec
[ 1] 2.0000-3.0000 sec 112 MBytes 935 Mbits/sec
[ 1] 3.0000-4.0000 sec 111 MBytes 933 Mbits/sec
[ 1] 4.0000-5.0000 sec 111 MBytes 934 Mbits/sec
[ 1] 5.0000-6.0000 sec 111 MBytes 933 Mbits/sec
[ 1] 6.0000-7.0000 sec 111 MBytes 931 Mbits/sec
[ 1] 7.0000-8.0000 sec 112 MBytes 935 Mbits/sec
[ 1] 8.0000-9.0000 sec 111 MBytes 933 Mbits/sec
[ 1] 9.0000-10.0000 sec 112 MBytes 935 Mbits/sec
[ 1] 0.0000-10.0077 sec 1.09 GBytes 933 Mbits/sec

--- Non Page Pool implementation on i.MX8 ----

shenwei@5810:~$ iperf -c 10.81.16.245 -w 2m -i 1
------------------------------------------------------------
Client connecting to 10.81.16.245, TCP port 5001
TCP window size: 416 KByte (WARNING: requested 1.91 MByte)
------------------------------------------------------------
[ 1] local 10.81.17.20 port 49154 connected with 10.81.16.245 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.0000-1.0000 sec 104 MBytes 868 Mbits/sec
[ 1] 1.0000-2.0000 sec 105 MBytes 878 Mbits/sec
[ 1] 2.0000-3.0000 sec 105 MBytes 881 Mbits/sec
[ 1] 3.0000-4.0000 sec 105 MBytes 879 Mbits/sec
[ 1] 4.0000-5.0000 sec 105 MBytes 878 Mbits/sec
[ 1] 5.0000-6.0000 sec 105 MBytes 878 Mbits/sec
[ 1] 6.0000-7.0000 sec 104 MBytes 875 Mbits/sec
[ 1] 7.0000-8.0000 sec 104 MBytes 875 Mbits/sec
[ 1] 8.0000-9.0000 sec 104 MBytes 873 Mbits/sec
[ 1] 9.0000-10.0000 sec 104 MBytes 875 Mbits/sec
[ 1] 0.0000-10.0073 sec 1.02 GBytes 875 Mbits/sec

--- Page Pool implementation on i.MX6SX ----

shenwei@5810:~/pktgen$ iperf -c 10.81.16.245 -w 2m -i 1
------------------------------------------------------------
Client connecting to 10.81.16.245, TCP port 5001
TCP window size: 416 KByte (WARNING: requested 1.91 MByte)
------------------------------------------------------------
[ 1] local 10.81.17.20 port 57288 connected with 10.81.16.245 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.0000-1.0000 sec 78.8 MBytes 661 Mbits/sec
[ 1] 1.0000-2.0000 sec 82.5 MBytes 692 Mbits/sec
[ 1] 2.0000-3.0000 sec 82.4 MBytes 691 Mbits/sec
[ 1] 3.0000-4.0000 sec 82.4 MBytes 691 Mbits/sec
[ 1] 4.0000-5.0000 sec 82.5 MBytes 692 Mbits/sec
[ 1] 5.0000-6.0000 sec 82.4 MBytes 691 Mbits/sec
[ 1] 6.0000-7.0000 sec 82.5 MBytes 692 Mbits/sec
[ 1] 7.0000-8.0000 sec 82.4 MBytes 691 Mbits/sec
[ 1] 8.0000-9.0000 sec 82.4 MBytes 691 Mbits/sec
[ 1] 9.0000-9.5506 sec 45.0 MBytes 686 Mbits/sec
[ 1] 0.0000-9.5506 sec 783 MBytes 688 Mbits/sec

--- Non Page Pool implementation on i.MX6SX ----

shenwei@5810:~/pktgen$ iperf -c 10.81.16.245 -w 2m -i 1
------------------------------------------------------------
Client connecting to 10.81.16.245, TCP port 5001
TCP window size: 416 KByte (WARNING: requested 1.91 MByte)
------------------------------------------------------------
[ 1] local 10.81.17.20 port 36486 connected with 10.81.16.245 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.0000-1.0000 sec 70.5 MBytes 591 Mbits/sec
[ 1] 1.0000-2.0000 sec 64.5 MBytes 541 Mbits/sec
[ 1] 2.0000-3.0000 sec 73.6 MBytes 618 Mbits/sec
[ 1] 3.0000-4.0000 sec 73.6 MBytes 618 Mbits/sec
[ 1] 4.0000-5.0000 sec 72.9 MBytes 611 Mbits/sec
[ 1] 5.0000-6.0000 sec 73.4 MBytes 616 Mbits/sec
[ 1] 6.0000-7.0000 sec 73.5 MBytes 617 Mbits/sec
[ 1] 7.0000-8.0000 sec 73.4 MBytes 616 Mbits/sec
[ 1] 8.0000-9.0000 sec 73.4 MBytes 616 Mbits/sec
[ 1] 9.0000-10.0000 sec 73.9 MBytes 620 Mbits/sec
[ 1] 0.0000-10.0174 sec 723 MBytes 605 Mbits/sec

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add pm runtime force suspend and resume support

Force mii bus into runtime pm suspend state during device suspends,
since phydev state is already PHY_HALTED, and there is no need to
access mii bus during device suspend state. Then force mii bus into
runtime pm resume state when device resumes.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add stop mode support for imx8 platform

The current driver support stop mode by calling machine api.
The patch add dts support to set GPR register for stop request.

imx8mq enter stop/exit stop mode by setting GPR bit, which can
be accessed by A core.
imx8qm enter stop/exit stop mode by calling IMX_SC ipc APIs that
communicate with M core ipc service, and the M core set the related
GPR bit at last.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "net: fec: Use a spinlock to guard `fep->ptp_clk_on`"

This reverts commit b353b241f1eb9b6265358ffbe2632fdcb563354f, this is
creating multiple issues, just not ready to be merged yet.

Link: https://lore.kernel.org/all/CAHk-=wj1obPoTu1AHj9Bd_BGYjdjDyPP+vT5WMj8eheb3A9WHw@mail.gmail.com/
Link: https://lore.kernel.org/all/20220907143915.5w65kainpykfobte@pengutronix.de/
Fixes: b353b241f1eb ("net: fec: Use a spinlock to guard `fep->ptp_clk_on`")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Revert "fec: Restart PPS after link state change"

This reverts commit f79959220fa5fbda939592bf91c7a9ea90419040, this is
creating multiple issues, just not ready to be merged yet.

Link: https://lore.kernel.org/all/20220905180542.GA3685102@roeck-us.net/
Link: https://lore.kernel.org/all/CAHk-=wj1obPoTu1AHj9Bd_BGYjdjDyPP+vT5WMj8eheb3A9WHw@mail.gmail.com/
Fixes: f79959220fa5 ("fec: Restart PPS after link state change")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: fec: Use a spinlock to guard `fep->ptp_clk_on`

Mutexes cannot be taken in a non-preemptible context,
causing a panic in `fec_ptp_save_state()`. Replacing
`ptp_clk_mutex` by `tmreg_lock` fixes this.

Fixes: 6a4d7234ae9a ("net: fec: ptp: avoid register access when ipg clock is disabled")
Fixes: f79959220fa5 ("fec: Restart PPS after link state change")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/all/20220827160922.642zlcd5foopozru@pengutronix.de/
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Apalis iMX6
Link: https://lore.kernel.org/r/20220901140402.64804-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec: add pm_qos support on imx6q platform

There is a very low probability that tx timeout will occur during
suspend and resume stress test on imx6q platform. So we add pm_qos
support to prevent system from entering low level idles which may
affect the transmission of tx.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20220830070148.2021947-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

fec: Restart PPS after link state change

On link state change, the controller gets reset,
causing PPS to drop out and the PHC to lose its
time and calibration. So we restart it if needed,
restoring calibration and time registers.

Changes since v2:
* Add `fec_ptp_save_state()`/`fec_ptp_restore_state()`
* Use `ktime_get_real_ns()`
* Use `BIT()` macro
Changes since v1:
* More ECR #define's
* Stop PPS in `fec_ptp_stop()`

Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: only clear interrupt of handling queue in fec_enet_rx_queue()

Background:
We have a customer is running a Profinet stack on the 8MM which receives and
responds PNIO packets every 4ms and PNIO-CM packets every 40ms. However, from
time to time the received PNIO-CM package is "stock" and is only handled when
receiving a new PNIO-CM or DCERPC-Ping packet (tcpdump shows the PNIO-CM and
the DCERPC-Ping packet at the same time but the PNIO-CM HW timestamp is from
the expected 40 ms and not the 2s delay of the DCERPC-Ping).

After debugging, we noticed PNIO, PNIO-CM and DCERPC-Ping packets would
be handled by different RX queues.

The root cause should be driver ack all queues' interrupt when handle a
specific queue in fec_enet_rx_queue(). The blamed patch is introduced to
receive as much packets as possible once to avoid interrupt flooding.
But it's unreasonable to clear other queues'interrupt when handling one
queue, this patch tries to fix it.

Fixes: ed63f1dcd578 (net: fec: clear receive interrupts before processing a packet)
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Nicolas Diaz <nicolas.diaz@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20211206135457.15946-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec: add WoL support for i.MX8MQ

By default FEC driver treat irq[0] (i.e. int0 described in dt-binding) as
wakeup interrupt, but this situation changed on i.MX8M serials, SoC
integration guys mix wakeup interrupt signal into int2 interrupt line.
This patch introduces FEC_QUIRK_WAKEUP_FROM_INT2 to indicate int2 as wakeup
interrupt for i.MX8MQ.

Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20210812070948.25797-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec: fix build error for ARCH m68k

reproduce:
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
make.cross ARCH=m68k m5272c3_defconfig
make.cross ARCH=m68k

drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_eee_mode_set':
>> drivers/net/ethernet/freescale/fec_main.c:2758:33: error: 'FEC_LPI_SLEEP' undeclared (first use in this function); did you mean 'FEC_ECR_SLEEP'?
2758 | writel(sleep_cycle, fep->hwp + FEC_LPI_SLEEP);
| ^~~~~~~~~~~~~
arch/m68k/include/asm/io_no.h:25:66: note: in definition of macro '__raw_writel'
25 | #define __raw_writel(b, addr) (void)((*(__force volatile u32 *) (addr)) = (b))
| ^~~~
drivers/net/ethernet/freescale/fec_main.c:2758:2: note: in expansion of macro 'writel'
2758 | writel(sleep_cycle, fep->hwp + FEC_LPI_SLEEP);
| ^~~~~~
drivers/net/ethernet/freescale/fec_main.c:2758:33: note: each undeclared identifier is reported only once for each function it appears in
2758 | writel(sleep_cycle, fep->hwp + FEC_LPI_SLEEP);
| ^~~~~~~~~~~~~
arch/m68k/include/asm/io_no.h:25:66: note: in definition of macro '__raw_writel'
25 | #define __raw_writel(b, addr) (void)((*(__force volatile u32 *) (addr)) = (b))
| ^~~~
drivers/net/ethernet/freescale/fec_main.c:2758:2: note: in expansion of macro 'writel'
2758 | writel(sleep_cycle, fep->hwp + FEC_LPI_SLEEP);
| ^~~~~~
>> drivers/net/ethernet/freescale/fec_main.c:2759:32: error: 'FEC_LPI_WAKE' undeclared (first use in this function)
2759 | writel(wake_cycle, fep->hwp + FEC_LPI_WAKE);
| ^~~~~~~~~~~~
arch/m68k/include/asm/io_no.h:25:66: note: in definition of macro '__raw_writel'
25 | #define __raw_writel(b, addr) (void)((*(__force volatile u32 *) (addr)) = (b))
| ^~~~
drivers/net/ethernet/freescale/fec_main.c:2759:2: note: in expansion of macro 'writel'
2759 | writel(wake_cycle, fep->hwp + FEC_LPI_WAKE);
| ^~~~~~

This patch adds register definition for M5272 platform to pass build.

Fixes: b82f8c3f1409 ("net: fec: add eee mode tx lpi support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add MAC internal delayed clock feature support

i.MX8QM ENET IP version support timing specification that MAC
integrate clock delay in RGMII mode, the delayed TXC/RXC as an
alternative option to work well with various PHYs.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add eee mode tx lpi support

The i.MX8MQ ENET version support IEEE802.3az eee mode, add
eee mode tx lpi enable to support ethtool interface.

usage:
1. set sleep and wake timer to 5ms:
ethtool --set-eee eth0 eee on tx-lpi on tx-timer 5000
2. check the eee mode:
~# ethtool --show-eee eth0
EEE Settings for eth0:
EEE status: enabled - active
Tx LPI: 5000 (us)
Supported EEE link modes: 100baseT/Full
1000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
Link partner advertised EEE link modes: 100baseT/Full

Note: For realtime case and IEEE1588 ptp case, it should disable
EEE mode.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add imx8mq and imx8qm new versions support

The ENET of imx8mq and imx8qm are basically the same as imx6sx,
but they have new features support based on imx6sx, like:
- imx8mq: supports IEEE 802.3az EEE standard.
- imx8qm: supports RGMII mode delayed clock.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add FEC_QUIRK_HAS_MULTI_QUEUES represents i.MX6SX ENET IP

Frieder Schrempf reported a TX throuthput issue [1], it happens quite often
that the measured bandwidth in TX direction drops from its expected/nominal
value to something like ~50% (for 100M) or ~67% (for 1G) connections.

[1] https://lore.kernel.org/linux-arm-kernel/421cc86c-b66f-b372-32f7-21e59f9a98bc@kontron.de/

The issue becomes clear after digging into it, Net core would select
queues when transmitting packets. Since FEC have not impletemented
ndo_select_queue callback yet, so it will call netdev_pick_tx to select
queues randomly.

For i.MX6SX ENET IP with AVB support, driver default enables this
feature. According to the setting of QOS/RCMRn/DMAnCFG registers, AVB
configured to Credit-based scheme, 50% bandwidth of each queue 1&2.

With below tests let me think more:
1) With FEC_QUIRK_HAS_AVB quirk, can reproduce TX bandwidth fluctuations issue.
2) Without FEC_QUIRK_HAS_AVB quirk, can't reproduce TX bandwidth fluctuations issue.

The related difference with or w/o FEC_QUIRK_HAS_AVB quirk is that, whether we
program FTYPE field of TxBD or not. As I describe above, AVB feature is
enabled by default. With FEC_QUIRK_HAS_AVB quirk, frames in queue 0
marked as non-AVB, and frames in queue 1&2 marked as AVB Class A&B. It's
unreasonable if frames in queue 1&2 are not required to be time-sensitive.
So when Net core select tx queues ramdomly, Credit-based scheme would work
and lead to TX bandwidth fluctuated. On the other hand, w/o
FEC_QUIRK_HAS_AVB quirk, frames in queue 1&2 are all marked as non-AVB, so
Credit-based scheme would not work.

Till now, how can we fix this TX throughput issue? Yes, please remove
FEC_QUIRK_HAS_AVB quirk if you suffer it from time-nonsensitive networking.
However, this quirk is used to indicate i.MX6SX, other setting depends
on it. So this patch adds a new quirk FEC_QUIRK_HAS_MULTI_QUEUES to
represent i.MX6SX, it is safe for us remove FEC_QUIRK_HAS_AVB quirk
now.

FEC_QUIRK_HAS_AVB quirk is set by default in the driver, and users may
not know much about driver details, they would waste effort to find the
root cause, that is not we want. The following patch is a implementation
to fix it and users don't need to modify the driver.

Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reported-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: Fix temporary RMII clock reset on link up

fec_restart() does a hard reset of the MAC module when the link status
changes to up. This temporarily resets the R_CNTRL register which controls
the MII mode of the ENET_OUT clock. In the case of RMII, the clock
frequency momentarily drops from 50MHz to 25MHz until the register is
reconfigured. Some link partners do not tolerate this glitch and
invalidate the link causing failure to establish a stable link when using
PHY polling mode. Since as per IEEE802.3 the criteria for link validity
are PHY-specific, what the partner should tolerate cannot be assumed, so
avoid resetting the MII clock by using software reset instead of hardware
reset when the link is up. This is generally relevant only if the SoC
provides the clock to an external PHY and the PHY is configured for RMII.

Signed-off-by: Laurent Badel <laurentbadel@eaton.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec: fix MDIO probing for some FEC hardware blocks

Some (apparently older) versions of the FEC hardware block do not like
the MMFR register being cleared to avoid generation of MII events at
initialization time. The action of clearing this register results in no
future MII events being generated at all on the problem block. This means
the probing of the MDIO bus will find no PHYs.

Create a quirk that can be checked at the FECs MII init time so that
the right thing is done. The quirk is set as appropriate for the FEC
hardware blocks that are known to need this.

Fixes: f166f890c8f0 ("net: ethernet: fec: Replace interrupt driven MDIO with polled IO")
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Fugang Duan <fugand.duan@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Link: https://lore.kernel.org/r/20201028052232.1315167-1-gerg@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec: fix hardware time stamping by external devices

Fix support for external PTP-aware devices such as DSA or PTP PHY:

Make sure we never time stamp tx packets when hardware time stamping
is disabled.

Check for PTP PHY being in use and then pass ioctls related to time
stamping of Ethernet packets to the PTP PHY rather than handle them
ourselves. In addition, disable our own hardware time stamping in this
case.

Fixes: 6605b730c061 ("FEC: Add time stamping code and a PTP hardware clock")
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: fec: prevent tx starvation under high rx load

In the ISR, we poll the event register for the queues in need of
service and then enter polled mode. After this point, the event
register will never be read again until we exit polled mode.

In a scenario where a UDP flow is routed back out through the same
interface, i.e. "router-on-a-stick" we'll typically only see an rx
queue event initially. Once we start to process the incoming flow
we'll be locked polled mode, but we'll never clean the tx rings since
that event is never caught.

Eventually the netdev watchdog will trip, causing all buffers to be
dropped and then the process starts over again.

Rework the NAPI poll to keep trying to consome the entire budget as
long as new events are coming in, making sure to service all rx/tx
queues, in priority order, on each pass.

Fixes: 4d494cdc92b3 ("net: fec: change data structure to support multiqueue")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: fec: Replace interrupt driven MDIO with polled IO

Measurements of the MDIO bus have shown that driving the MDIO bus
using interrupts is slow. Back to back MDIO transactions take about
90us, with 25us spent performing the transaction, and the remainder of
the time the bus is idle.

Replacing the completion interrupt with polled IO results in back to
back transactions of 40us. The polling loop waiting for the hardware
to complete the transaction takes around 28us. Which suggests
interrupt handling has an overhead of 50us, and polled IO nearly
halves this overhead, and doubles the MDIO performance.

Care has to be taken when setting the MII_SPEED register, or it can
trigger an MII event> That then upsets the polling, due to an
unexpected pending event.

Suggested-by: Chris Heally <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: fec: Revert "net: ethernet: fec: Replace interrupt driven MDIO with polled IO"

This reverts commit 29ae6bd1b0d8a57d7c00ab12cbb949fc41986eef.

The commit breaks ethernet function on i.MX6SX, i.MX7D, i.MX8MM,
i.MX8MQ, and i.MX8QXP platforms. Boot yocto system by NFS mounting
rootfs will be failed with the commit.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: fec: Replace interrupt driven MDIO with polled IO

Measurements of the MDIO bus have shown that driving the MDIO bus
using interrupts is slow. Back to back MDIO transactions take about
90us, with 25us spent performing the transaction, and the remainder of
the time the bus is idle.

Replacing the completion interrupt with polled IO results in back to
back transactions of 40us. The polling loop waiting for the hardware
to complete the transaction takes around 28us. Which suggests
interrupt handling has an overhead of 50us, and polled IO nearly
halves this overhead, and doubles the MDIO performance.

Suggested-by: Chris Heally <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: set GPR bit on suspend by DT configuration.

On some SoCs, such as the i.MX6, it is necessary to set a bit
in the SoC level GPR register before suspending for wake on lan
to work.

The fec platform callback sleep_mode_enable was intended to allow this
but the platform implementation was NAK'd back in 2015 [1]

This means that, currently, wake on lan is broken on mainline for
the i.MX6 at least.

So implement the required bit setting in the fec driver by itself
by adding a new optional DT property indicating the GPR register
and adding the offset and bit information to the driver.

[1] https://www.spinics.net/lists/netdev/msg310922.html

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

freescale: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: remove workaround to restart phylib state machine on MDIO timeout

There's a workaround to restart the phylib state machine in case of a
MDIO access timeout. Seems it was introduced to deal with the
consequences of a too small MDIO timeout. See also commit message of
c3b084c24c8a ("net: fec: Adjust ENET MDIO timeouts") which increased
the timeout value later. Due to the later timeout value fix it seems
to be safe to remove the workaround.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: don't dump RX FIFO register when not available

Commit db65f35f50e0 ("net: fec: add support of ethtool get_regs") introduce
ethool "--register-dump" interface to dump all FEC registers.

But not all silicon implementations of the Freescale FEC hardware module
have the FRBR (FIFO Receive Bound Register) and FRSR (FIFO Receive Start
Register) register, so we should not be trying to dump them on those that
don't.

To fix it we create a quirk flag, FEC_QUIRK_HAS_RFREG, and check it before
dump those RX FIFO registers.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: freescale: Allow FEC with COMPILE_TEST

The Freescale FEC driver builds fine with COMPILE_TEST, so make that
possible.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add necessary defines to work on ARM64

The i.MX8 is a ARMv8 based SoC, that uses the same FEC IP as the
earlier, ARMv7 based, i.MX SoCs. Allow the driver to work on ARM64.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: Let fec_ptp have its own interrupt routine

This is better for code locality and should slightly
speed up normal interrupts.

This also allows PPS clock output to start working for
i.mx7. This is because i.mx7 was already using the limit
of 3 interrupts, and needed another.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: fec: remove unused interrupt FEC_ENET_TS_TIMER

FEC_ENET_TS_TIMER is not checked in the interrupt routine
so there is no need to enable it.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: Clear and enable MIB counters on imx51

Both the IMX51 and IMX53 datasheet indicates that the MIB counters
should be cleared during setup. Otherwise random numbers are returned
via ethtool -S. Add a quirk and a function to do this.

Tested on an IMX51.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: cache statistics while device is down

Execution 'ethtool -S' on fec device that is down causes OOPS on Vybrid
board:

Unhandled fault: external abort on non-linefetch (0x1008) at 0xe0898200
pgd = ddecc000
[e0898200] *pgd=9e406811, *pte=400d1653, *ppte=400d1453
Internal error: : 1008 [#1] SMP ARM
...

Reason of OOPS is that fec_enet_get_ethtool_stats() accesses fec
registers while IPG clock is stopped by PM.

Fix that by caching statistics in fec_enet_private. Cache is initialized
at device probe time, and updated at statistics request time if device
is up, and also just before turning device off on down path.

Additional locking is not needed, since cached statistics is accessed
either before device is registered, or under rtnl_lock().

Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add interrupt coalesc quirk flag

Different i.MX SOC FEC support different features like :
- i.MX6Q/DL FEC does not support AVB and interrupt coalesc
- i.MX6SX/i.MX7D supports AVB and interrupt coalesc
- i.MX6UL/ULL does not support AVB, but support interrupt coalesc

So, add new quirk flag to judge the supported features.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ARM: imx6: disable deeper idle states when FEC is active w/o HW workaround

The i.MX6 Q/DL has an erratum (ERR006687) that prevents the FEC from
waking the CPUs when they are in wait(unclocked) state. As the hardware
workaround isn't applicable to all boards, disable the deeper idle state
when the workaround isn't present and the FEC is in use.

This allows to safely run a kernel with CPUidle enabled on all i.MX6
boards.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net> (for network changes)
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

net: ethernet: fec: use phydev from struct net_device

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the one
contained in struct net_device.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: don't disable FEC_ENET_TS_TIMER interrupt

Only the interrupt routine processes this condition.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add variable reg_desc_active to speed things up

There is no need for complex macros every time we need to activate
a queue. Also, no need to call skb_get_queue_mapping when we already
know which queue it is using.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add struct bufdesc_prop

This reduces code and gains speed.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: stop the "rcv is not +last, " error messages

Setting the FTRL register will stop the fec from
trying to use multiple receive buffers.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: use CONFIG_ARM instead of CONFIG_ARCH_MXC/SOC_IMX28

As Arnd Bergmann points out, using CONFIG_ARCH_MXC and/or SOC_IMX28
is wrong if some other ARM platform uses this device - the operation
of the driver would depend on an unrelated ARM platform that might
or might not be set for multi-platform kernels.

Prior to my previous patch, any other platforms using it would have
been broken already due to having the cbd_datlen/cbd_sc fields in
the wrong order, but byte ordering correctly, so no such platforms
can exist and work today.

In any case, it seems likely that only Freescale SoCs use this part,
and those are little-endian on ARM, so CONFIG_ARM is safe for them.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: make driver endian-safe

The driver treats the device descriptors as CPU-endian, which appears
to be correct with the default endianness on both ARM (typically LE)
and PowerPC (typically BE) SoCs, indicating that the hardware block
is generated differently. Add endianness annotations and byteswaps as
necessary.

It's not clear that the ifdef there really is correct and shouldn't
just be #ifdef CONFIG_ARM, but I also can't test on anything but the
i.MX6 HummingBoard where this gets it working with a BE kernel.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: introduce fec_ptp_stop and use in probe fail path

This function frees resources and cancels delayed work item that
have been initialized in fec_ptp_init().

Use this to do proper error handling if something goes wrong in
probe function after fec_ptp_init has been called.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: don't access RACC register when not available

Not all silicon implementations of the Freescale FEC hardware module
have the RACC (Receive Accelerator Function) register, so we should not
be trying to access it on those that don't. Currently none of the ColdFire
based parts with a FEC have it.

Support for RACC was introduced by commit 4c09eed9 ("net: fec: Enable imx6
enet checksum acceleration"). A fix was introduced in commit d1391930
("net: fec: Fix build for MCF5272") that disables its use on the ColdFire
M5272 part, but it doesn't fix the general case of other ColdFire parts.

To fix we create a quirk flag, FEC_QUIRK_HAS_RACC, and check it before
working with the RACC register.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: fix MDIO bus assignement for dual fec SoC's

On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.

Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)

This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.

However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.

Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add Wake-on-LAN support

Support for Wake-on-LAN using Magic Packet. ENET IP supports sleep mode
in low power status, when system enter suspend status, Magic packet can
wake up system even if all SOC clocks are gate. The patch doing below things:
- flagging the device as a wakeup source for the system, as well as
its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- add standard ethtool WOL interface
- enable the ENET interrupt to wake us

Tested on i.MX6q/dl sabresd, sabreauto boards, i.MX6SX arm2 boards.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

time: move the timecounter/cyclecounter code into its own file.

The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: init maximum receive buffer size for ring1 and ring2

i.MX6SX fec support three rx ring1, the current driver lost to init
ring1 and ring2 maximum receive buffer size, that cause receving
frame date length error. The driver reports "rcv is not +last" error
log in user case.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: improve access to quirk flags by copying them into fec_enet_private struct

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: change type of 'bufdesc_ex' to bool

fep->bufdesc_ex is treated as a boolean value, thus declare it as
such.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: properly parenthesize macro args

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: consistently use lower case chars as hex digits

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: indentation cleanup

consistently use TABs for indentation

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: ptp: fix convergence issue to support LinuxPTP stack

iMX6SX IEEE 1588 module has one hw issue in capturing the ATVR register.
The current SW flow is:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
ts_counter_ns = ENET0->ATVR;
The ATVR value is not expected value that cause LinuxPTP stack cannot be convergent.

ENET Block Guide/ Chapter for the iMX6SX (PELE) address the issue:
After set ENET_ATCR[Capture], there need some time cycles before the counter
value is capture in the register clock domain. The wait-time-cycles is at least
6 clock cycles of the slower clock between the register clock and the 1588 clock.
So need something like:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
wait();
ts_counter_ns = ENET0->ATVR;

For iMX6SX, the 1588 ts_clk is fixed to 25Mhz, register clock is 66Mhz, so the
wait-time-cycles must be greater than 240ns (40ns * 6). The patch add 1us delay
before cpu read ATVR register.

Changes V2:
Modify the commit/comments log to describe the issue clearly.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: ptp: Enable PPS output based on ptp clock

FEC ptp timer has 4 channel compare/trigger function. It can be used to
enable pps output.
The pulse would be ouput high exactly on N second. The pulse ouput high
on compare event mode is used to produce pulse per second. The pulse
width would be one cycle based on ptp timer clock source.Since 31-bit
ptp hardware timer is used, the timer will wrap more than 2 seconds. We
need to reload the compare compare event about every 1 second.

Signed-off-by: Luwei Zhou <b45643@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: ptp: Use hardware algorithm to adjust PTP counter.

The FEC IP supports hardware adjustment for ptp timer. Refer to the description of
ENET_ATCOR and ENET_ATINC registers in the spec about the hardware adjustment. This
patch uses hardware support to adjust the ptp offset and frequency on the slave side.

Signed-off-by: Luwei Zhou <b45643@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Fugang Duan <b38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: implement rx_copybreak to improve rx performance

- Copy short frames and keep the buffers mapped, re-allocate skb instead of
memory copy for long frames.
- Add support for setting/getting rx_copybreak using generic ethtool tunable

Changes V3:
* As Eric Dumazet's suggestion that removing the copybreak module parameter
and only keep the ethtool API support for rx_copybreak.

Changes V2:
* Implements rx_copybreak
* Rx_copybreak provides module parameter to change this value
* Add tunable_ops support for rx_copybreak

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: Add Ftype to BD to distiguish three tx queues for AVB

The current driver loss Ftype field init for BD, which cause tx
queue #1 and #2 cannot work well.

Add Ftype field to BD to distiguish three queues for AVB:
0 -> Best Effort
1 -> ClassA
2 -> ClassB

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net:fec: increase DMA queue number

when enable interrupt coalesce, 8 BD is not enough.

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add interrupt coalescence feature support

i.MX6 SX support interrupt coalescence feature
By default, init the interrupt coalescing frame count threshold and
timer threshold.

Supply the ethtool interfaces as below for user tuning to improve
enet performance:
rx_max_coalesced_frames
rx_coalesce_usecs
tx_max_coalesced_frames
tx_coalesce_usecs

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: fix build error at m68k platform

reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
git checkout 4d494cdc92b3b9a0f5fb9e1560810fa27d5a0489
make.cross ARCH=m68k m5272c3_defconfig
make.cross ARCH=m68k

drivers/net/ethernet/freescale/fec.h:262:0: warning: "FEC_R_DES_START" redefined
#define FEC_R_DES_START(X) ((X == 1) ? FEC_R_DES_START_1 : \
^
drivers/net/ethernet/freescale/fec.h:158:0: note: this is the location of the previous definition
#define FEC_R_DES_START 0x3d0 /* Receive descriptor ring */
^
drivers/net/ethernet/freescale/fec.h:265:0: warning: "FEC_X_DES_START" redefined
#define FEC_X_DES_START(X) ((X == 1) ? FEC_X_DES_START_1 : \

...

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: change FEC alignment according to i.mx6 sx requirement

i.MX6 SX change FEC alignment requirement.
i.MX6 SX change internal bus from AHB to AXI.
It require RX buffer must be 64 bytes alignment.
And remove TX buffer alignment requirement.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add enet-avb IP support

i.MX6SX Enet-AVB support 3 tx queues, 3 rx queues.
For tx queues: ring 0 -> best effort
ring 1 -> Class A
ring 2 -> Class B
For rx queues:
ring 0 -> best effort
ring 1 -> receive VLAN packet with classification match
ring 2 -> receive VLAN packet with classification match

Add enet-avb IP multiqueue support for the driver.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: parser max queue number from dt file

By default, the tx/rx queue number is 1, user can config the queue number
at DTS file like this:
fsl,num-tx-queues=<3>;
fsl,num-rx-queues=<3>

Since i.MX6SX enet-AVB IP support multi queues, so use multi queues
interface to allocate and set up an Ethernet device.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: change data structure to support multiqueue

This patch just change data structure to support multi-queue.
Only 1 queue enabled.

Ethernet multiqueue mechanism can improve performance in SMP system.
For single hw queue, multiqueue can balance cpu loading.
For multi hw queues, multiple cores can process network packets in parallel,
and refer the article for the detail advantage for multiqueue:
http://vger.kernel.org/~davem/davem_nyc09.pdf

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net:fec: add enet refrence clock for i.MX 6SX chip

i.MX6sx enet has below clocks for user config:
clk_ipg: ipg_clk_s, ipg_clk_mac0_s, 66Mhz
clk_ahb: enet system clock, it is enet AXI clock for imx6sx.
For imx6sx, it alos is the clock source of interrupt coalescing.
The clock range: 200Mhz ~ 266Mhz.
clk_ref: refrence clock for tx and rx. For imx6sx enet RGMII mode,
the refrence clock is 125Mhz coming from internal PLL or external.
In i.MX6sx-arm2 board, the clock is from internal PLL.
clk_ref is optional, depends on board.
clk_enet_out: The clock can be output from internal PLL. It can supply 50Mhz
clock for phy. clk_enet_out is optional, depends on chip and board.
clk_ptp: 1588 ts clock. It is optional, depends on chip.

The patch add clk_ref to distiguish the different clocks.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: ptp: avoid register access when ipg clock is disabled

The current kernel hang on i.MX6SX with rootfs mount from MMC.
The root cause is that ptp uses a periodic timer to access enet register
even if ipg clock is disabled.

FEC ptp driver start one period timer to read 1588 counter register in the
ptp init function that is called after FEC driver is probed.

To save power, after FEC probe finish, FEC driver disable all clocks including
ipg clock that is needed for register access.

i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock
is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang.

To avoid the issue, we need to check ptp clock status before ptp timer count access.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: Support phys probed from devicetree and fixed-link

This adds support for specifying the phy to be used with the fec in the
devicetree using the standard phy-handle property and also supports
fixed-link.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: replace delayed work with standard work

As of "better implementation of iMX6 ERR006358 quirk", we no longer have
a requirement for a delayed work. Moreover, the work is now only used
for timeout purposes, so the timeout flag is also pointless - we set it
each time we queue the work, and the work clears it.

Replace the fec_enet_delayed_work struct with a standard work_struct,
resulting in simplified timeout handling code.

Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: better implementation of iMX6 ERR006358 quirk

Using a (delayed) workqueue for ERR006358 is not correct - a work queue
is a single-trigger device. Once the work queue has been scheduled, it
can't be re-scheduled until it has been run. This can cause problems -
with an appropriate packet timing, we can end up with packets queued,
but not sent by the hardware, resulting in the transmit timeout firing.

Re-implement this as per the workaround detailed in the ERR006358
documentation - if there are packets waiting to be sent when we service
the transmit ring, and we see that the transmitter is not running,
kick the transmitter to run the pending entries in the ring.

Testing here with a 10Mbit half duplex link sees the resulting iperf
TCP bandwidth increase from between 1 to 2Mbps to between 8 to 9Mbps.

Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: remove useless fep->opened

napi_disable() waits until the NAPI processing has completed, and then
prevents any further polls. At this point, the driver then clears
fep->opened. The NAPI poll function uses this to stop processing in
the receive path. Hence, it will never see this variable cleared,
because the NAPI poll has to complete before it will be cleared.

Therefore, this variable serves no purpose, so let's remove it.

Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: Add software TSO support

Add software TSO support for FEC.
This feature allows to improve outbound throughput performance.

Tested on imx6dl sabresd board, running iperf tcp tests shows:
- 16.2% improvement comparing with FEC SG patch
- 82% improvement comparing with NO SG & TSO patch

$ ethtool -K eth0 tso on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 35388 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 181 MBytes 506 Mbits/sec

During the testing, CPU loading is 30%.
Since imx6dl FEC Bandwidth is limited to SOC system bus bandwidth, the
performance with SW TSO is a milestone.

CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: Add Scatter/gather support

Add Scatter/gather support for FEC.
This feature allows to improve outbound throughput performance.

Tested on imx6dl sabresd board:
Running iperf tests shows a 55.4% improvement.

$ ethtool -K eth0 sg off
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52618 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 99.5 MBytes 278 Mbits/sec

$ ethtool -K eth0 sg on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52617 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 154 MBytes 432 Mbits/sec

CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: Increase buffer descriptor entry number

In order to support SG, software TSO, let's increase BD entry number.

CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: Factorize the .xmit transmit function

Make the code more readable and easy to support other features like
SG, TSO, moving the common transmit function to one api.

And the patch also factorize the getting BD index to it own function.

CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fec: Implement the SIOCGHWTSTAMP ioctl

This is untested.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

net: fec: fix the error to get the previous BD entry

Bug: error to get the previous BD entry. When the current BD
is the first BD, the previous BD entry must be the last BD,
not "bdp - 1" in current logic.

V4:
* Optimize fec_enet_get_nextdesc() for code clean.
Replace "ex_new_bd - ring_size" with "ex_base".
Replace "new_bd - ring_size" with "base".

V3:
* Restore the API name because David suggest to use fec_enet_
prefix for all function in fec driver.
So, change next_bd() -> fec_enet_get_nextdesc()
change pre_bd() -> fec_enet_get_prevdesc()
* Reduce the two APIs parameters for easy to call.

V2:
* Add tx_ring_size and rx_ring_size to struct fec_enet_private.
* Replace api fec_enet_get_nextdesc() with next_bd().
Replace api fec_enet_get_prevdesc() with pre_bd().

* Move all ring size check logic to next_bd() and pre_bd(), which
simplifies the code redundancy.

V1:
* Add BD ring size check to get the previous BD entry in correctly.

Reviewed-by: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <frank.li@freescale.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: workaround stop tx during errata ERR006358

If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].

Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.

This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.

How to test:
while [ true ]
do
ping <IP> -s 10000 -w 4
ping <IP> -s 6000 -w 2
ping <IP> -s 4000 -w 2
ping <IP> -s 10000 -w 2
done

You will see below result in overnight test.

6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms

After apply this patch, >1000ms delay disappear.

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: Add VLAN receive HW support.

This enables the driver to take advantage of the FEC VLAN
indicator to improve performance.

Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fec: Add support for reading RMON registers

Add ethtool operation to read RMON registers.

Tested against net-next on i.MX28.

v2: make conditional on #ifndef CONFIG_M5272

Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fec: Only pass pdev in fec_ptp_init()

Passing pdev in fec_ptp_init() is enough, since we can get ndev locally.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fec: Place the phy regulator in the private structure

Instead of using a local reg_phy structure, let's put it inside the private
structure, so that we are able to have access to the regulator structure even
when we are outside fec_probe().

This is in preparation for controlling the FEC PHY regulator in the suspend and
resume functions.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: fix kernel oops when plug/unplug cable many times

reproduce steps
1. flood ping from other machine
ping -f -s 41000 IP
2. run below script
while [ 1 ]; do ethtool -s eth0 autoneg off;
sleep 3;ethtool -s eth0 autoneg on; sleep 4; done;

You can see oops in one hour.

The reason is fec_restart clear BD but NAPI may use it.
The solution is disable NAPI and stop xmit when reset BD.
disable NAPI may sleep, so fec_restart can't be call in
atomic context.

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: Enable imx6 enet checksum acceleration.

Enables hardware generation of IP header and
protocol specific checksums for transmitted
packets.

Enabled hardware discarding of received packets with
invalid IP header or protocol specific checksums.

The feature is enabled by default but can be
enabled/disabled by ethtool.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: freescale: fec: add support for optional enet_out clk

Some MX28 boards need the internal enet_out clock to be enabled. So, do
this in the driver iff the clock was referenced via devicetree.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>

net: fec: restart the FEC when PHY speed changes

Proviously we would only restart the FEC when PHY link or duplex state
changed. PHY does not always bring down the link for speed changes, in
which case we would not detect any change and keep FEC running.

Switching link speed without restarting the FEC results in the FEC being
stuck in an indefinite state, generating error conditions for every
packet.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: fix build error in no MXC platform

build error cause by
Commit ff43da86c69d76a726ffe7d1666148960dc1d108
("NET: FEC: dynamtic check DMA desc buff type")

drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_nextdesc’:
drivers/net/ethernet/freescale/fec.c:215:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_prevdesc’:
drivers/net/ethernet/freescale/fec.c:224:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_start_xmit’:
drivers/net/ethernet/freescale/fec.c:286:37: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:287:13: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:324:7: error: dereferencing pointer to incomplete type etc....

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: put tx to napi poll function to fix dead lock

up stack ndo_start_xmit already hold lock.
fec_enet_start_xmit needn't spin lock.
stat_xmit just update fep->cur_tx
fec_enet_tx just update fep->dirty_tx

Reserve a empty bdb to check full or empty
cur_tx == dirty_tx means full
cur_tx == dirty_tx +1 means empty

So needn't is_full variable.

Fix spin lock deadlock

=================================
[ INFO: inconsistent lock state ]
3.8.0-rc5+ #107 Not tainted
---------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
ptp4l/615 [HC1[1]:SC0[0]:HE0:SE1] takes:
(&(&list->lock)->rlock#3){?.-...}, at: [<8042c3c4>] skb_queue_tail+0x20/0x50
{HARDIRQ-ON-W} state was registered at:
[<80067250>] mark_lock+0x154/0x4e8
[<800676f4>] mark_irqflags+0x110/0x1a4
[<80069208>] __lock_acquire+0x494/0x9c0
[<80069ce8>] lock_acquire+0x90/0xa4
[<80527ad0>] _raw_spin_lock_bh+0x44/0x54
[<804877e0>] first_packet_length+0x38/0x1f0
[<804879e4>] udp_poll+0x4c/0x5c
[<804231f8>] sock_poll+0x24/0x28
[<800d27f0>] do_poll.isra.10+0x120/0x254
[<800d36e4>] do_sys_poll+0x15c/0x1e8
[<800d3828>] sys_poll+0x60/0xc8
[<8000e780>] ret_fast_syscall+0x0/0x3c

*** DEADLOCK ***

1 lock held by ptp4l/615:
#0: (&(&fep->hw_lock)->rlock){-.-...}, at: [<80355f9c>] fec_enet_tx+0x24/0x268
stack backtrace:
Backtrace:
[<800121e0>] (dump_backtrace+0x0/0x10c) from [<80516210>] (dump_stack+0x18/0x1c)
r6:8063b1fc r5:bf38b2f8 r4:bf38b000 r3:bf38b000
[<805161f8>] (dump_stack+0x0/0x1c) from [<805189d0>] (print_usage_bug.part.34+0x164/0x1a4)
[<8051886c>] (print_usage_bug.part.34+0x0/0x1a4) from [<80518a88>] (print_usage_bug+0x78/0x88)
r8:80065664 r7:bf38b2f8 r6:00000002 r5:00000000 r4:bf38b000
[<80518a10>] (print_usage_bug+0x0/0x88) from [<80518b58>] (mark_lock_irq+0xc0/0x270)
r7:bf38b000 r6:00000002 r5:bf38b2f8 r4:00000000
[<80518a98>] (mark_lock_irq+0x0/0x270) from [<80067270>] (mark_lock+0x174/0x4e8)
[<800670fc>] (mark_lock+0x0/0x4e8) from [<80067744>] (mark_irqflags+0x160/0x1a4)
[<800675e4>] (mark_irqflags+0x0/0x1a4) from [<80069208>] (__lock_acquire+0x494/0x9c0)
r5:00000002 r4:bf38b2f8
[<80068d74>] (__lock_acquire+0x0/0x9c0) from [<80069ce8>] (lock_acquire+0x90/0xa4)
[<80069c58>] (lock_acquire+0x0/0xa4) from [<805278d8>] (_raw_spin_lock_irqsave+0x4c/0x60)
[<8052788c>] (_raw_spin_lock_irqsave+0x0/0x60) from [<8042c3c4>] (skb_queue_tail+0x20/0x50)
r6:bfbb2180 r5:bf1d0190 r4:bf1d0184
[<8042c3a4>] (skb_queue_tail+0x0/0x50) from [<8042c4cc>] (sock_queue_err_skb+0xd8/0x188)
r6:00000056 r5:bfbb2180 r4:bf1d0000 r3:00000000
[<8042c3f4>] (sock_queue_err_skb+0x0/0x188) from [<8042d15c>] (skb_tstamp_tx+0x70/0xa0)
r6:bf0dddb0 r5:bf1d0000 r4:bfbb2180 r3:00000004
[<8042d0ec>] (skb_tstamp_tx+0x0/0xa0) from [<803561d0>] (fec_enet_tx+0x258/0x268)
r6:c089d260 r5:00001c00 r4:bfbd0000
[<80355f78>] (fec_enet_tx+0x0/0x268) from [<803562cc>] (fec_enet_interrupt+0xec/0xf8)
[<803561e0>] (fec_enet_interrupt+0x0/0xf8) from [<8007d5b0>] (handle_irq_event_percpu+0x54/0x1a0)
[<8007d55c>] (handle_irq_event_percpu+0x0/0x1a0) from [<8007d740>] (handle_irq_event+0x44/0x64)
[<8007d6fc>] (handle_irq_event+0x0/0x64) from [<80080690>] (handle_fasteoi_irq+0xc4/0x15c)
r6:bf0dc000 r5:bf811290 r4:bf811240 r3:00000000
[<800805cc>] (handle_fasteoi_irq+0x0/0x15c) from [<8007ceec>] (generic_handle_irq+0x28/0x38)
r5:807130c8 r4:00000096
[<8007cec4>] (generic_handle_irq+0x0/0x38) from [<8000f16c>] (handle_IRQ+0x54/0xb4)
r4:8071d280 r3:00000180
[<8000f118>] (handle_IRQ+0x0/0xb4) from [<80008544>] (gic_handle_irq+0x30/0x64)
r8:8000e924 r7:f4000100 r6:bf0ddef8 r5:8071c974 r4:f400010c
r3:00000000
[<80008514>] (gic_handle_irq+0x0/0x64) from [<8000e2e4>] (__irq_svc+0x44/0x5c)
Exception stack(0xbf0ddef8 to 0xbf0ddf40)

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: add napi support to improve proformance

Add napi support

Before this patch

iperf -s -i 1
------------------------------------------------------------
Server listening on TCP port 5001
TCP window size: 85.3 KByte (default)
------------------------------------------------------------
[ 4] local 10.192.242.153 port 5001 connected with 10.192.242.138 port 50004
[ ID] Interval Transfer Bandwidth
[ 4] 0.0- 1.0 sec 41.2 MBytes 345 Mbits/sec
[ 4] 1.0- 2.0 sec 43.7 MBytes 367 Mbits/sec
[ 4] 2.0- 3.0 sec 42.8 MBytes 359 Mbits/sec
[ 4] 3.0- 4.0 sec 43.7 MBytes 367 Mbits/sec
[ 4] 4.0- 5.0 sec 42.7 MBytes 359 Mbits/sec
[ 4] 5.0- 6.0 sec 43.8 MBytes 367 Mbits/sec
[ 4] 6.0- 7.0 sec 43.0 MBytes 361 Mbits/sec

After this patch
[ 4] 2.0- 3.0 sec 51.6 MBytes 433 Mbits/sec
[ 4] 3.0- 4.0 sec 51.8 MBytes 435 Mbits/sec
[ 4] 4.0- 5.0 sec 52.2 MBytes 438 Mbits/sec
[ 4] 5.0- 6.0 sec 52.1 MBytes 437 Mbits/sec
[ 4] 6.0- 7.0 sec 52.1 MBytes 437 Mbits/sec
[ 4] 7.0- 8.0 sec 52.3 MBytes 439 Mbits/sec

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: enable pause frame to improve rx prefomance for 1G network

The limition of imx6 internal bus cause fec can't achieve 1G perfomance.
There will be many packages lost because FIFO over run.

This patch enable pause frame flow control.

Before this patch
iperf -s -i 1
TCP window size: 85.3 KByte (default)
------------------------------------------------------------
[ 4] local 10.192.242.153 port 5001 connected with 10.192.242.94 port 49773
[ ID] Interval Transfer Bandwidth
[ 4] 0.0- 1.0 sec 6.35 MBytes 53.3 Mbits/sec
[ 4] 1.0- 2.0 sec 3.39 MBytes 28.5 Mbits/sec
[ 4] 2.0- 3.0 sec 2.63 MBytes 22.1 Mbits/sec
[ 4] 3.0- 4.0 sec 1.10 MBytes 9.23 Mbits/sec

ifconfig
RX packets:46195 errors:1859 dropped:1 overruns:1859 frame:1859

After this patch
iperf -s -i 1

[ 4] local 10.192.242.153 port 5001 connected with 10.192.242.94 port 49757
[ ID] Interval Transfer Bandwidth
[ 4] 0.0- 1.0 sec 49.8 MBytes 418 Mbits/sec
[ 4] 1.0- 2.0 sec 50.1 MBytes 420 Mbits/sec
[ 4] 2.0- 3.0 sec 47.5 MBytes 399 Mbits/sec
[ 4] 3.0- 4.0 sec 45.9 MBytes 385 Mbits/sec
[ 4] 4.0- 5.0 sec 44.8 MBytes 376 Mbits/sec

ifconfig
RX packets:2348454 errors:0 dropped:16 overruns:0 frame:0

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NET: FEC: dynamtic check DMA desc buff type

MX6 and mx28 support enhanced DMA descriptor buff to support 1588
ptp. But MX25, MX3x, MX5x can't support enhanced DMA descriptor buff.
Check fec type and choose correct DMA descriptor buff type.

Remove static config CONFIG_FEC_PTP.
ptp function will be auto detected.

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

FEC: Add time stamping code and a PTP hardware clock

This patch adds a driver for the FEC(MX6) that offers time
stamping and a PTP haderware clock. Because FEC\ENET(MX6)
hardware frequency adjustment is complex, we have implemented
this in software by changing the multiplication factor of the
timecounter.

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: move fec_enet_private to header file

A new file fec_ptp.c will use fec_enet_private to support 1588 PTP
move such structure to common header file fec.h

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fsl: fec: handle 10Mbps speed in RMII mode

when the link is 10 Mbps and the mode is RMII, it's necessary
to set FRCONT to 1 in MIIGSK_CFGR to divide the RMII source
clock by 10 in order to support 10 Mbps operations.

Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

freescale: Move the Freescale drivers

Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.

CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Shlomi Gridish <gridish@freescale.com>
CC: Li Yang <leoli@freescale.com>
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: Dan Malek <dmalek@jlc.net>
CC: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>