1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * DRM driver for Solomon SSD13xx OLED displays 4 * 5 * Copyright 2022 Red Hat Inc. 6 * Author: Javier Martinez Canillas <javierm@redhat.com> 7 * 8 * Based on drivers/video/fbdev/ssd1307fb.c 9 * Copyright 2012 Free Electrons 10 */ 11 12#include <linux/backlight.h> 13#include <linux/bitfield.h> 14#include <linux/bits.h> 15#include <linux/delay.h> 16#include <linux/gpio/consumer.h> 17#include <linux/property.h> 18#include <linux/pwm.h> 19#include <linux/regulator/consumer.h> 20 21#include <drm/drm_atomic.h> 22#include <drm/drm_atomic_helper.h> 23#include <drm/drm_crtc_helper.h> 24#include <drm/drm_damage_helper.h> 25#include <drm/drm_edid.h> 26#include <drm/drm_fbdev_generic.h> 27#include <drm/drm_format_helper.h> 28#include <drm/drm_framebuffer.h> 29#include <drm/drm_gem_atomic_helper.h> 30#include <drm/drm_gem_framebuffer_helper.h> 31#include <drm/drm_gem_shmem_helper.h> 32#include <drm/drm_managed.h> 33#include <drm/drm_modes.h> 34#include <drm/drm_rect.h> 35#include <drm/drm_probe_helper.h> 36 37#include "ssd130x.h" 38 39#define DRIVER_NAME "ssd130x" 40#define DRIVER_DESC "DRM driver for Solomon SSD13xx OLED displays" 41#define DRIVER_DATE "20220131" 42#define DRIVER_MAJOR 1 43#define DRIVER_MINOR 0 44 45#define SSD130X_PAGE_HEIGHT 8 46 47#define SSD132X_SEGMENT_WIDTH 2 48 49/* ssd13xx commands */ 50#define SSD13XX_CONTRAST 0x81 51#define SSD13XX_SET_SEG_REMAP 0xa0 52#define SSD13XX_SET_MULTIPLEX_RATIO 0xa8 53#define SSD13XX_DISPLAY_OFF 0xae 54#define SSD13XX_DISPLAY_ON 0xaf 55 56#define SSD13XX_SET_SEG_REMAP_MASK GENMASK(0, 0) 57#define SSD13XX_SET_SEG_REMAP_SET(val) FIELD_PREP(SSD13XX_SET_SEG_REMAP_MASK, (val)) 58 59/* ssd130x commands */ 60#define SSD130X_PAGE_COL_START_LOW 0x00 61#define SSD130X_PAGE_COL_START_HIGH 0x10 62#define SSD130X_SET_ADDRESS_MODE 0x20 63#define SSD130X_SET_COL_RANGE 0x21 64#define SSD130X_SET_PAGE_RANGE 0x22 65#define SSD130X_SET_LOOKUP_TABLE 0x91 66#define SSD130X_CHARGE_PUMP 0x8d 67#define SSD130X_START_PAGE_ADDRESS 0xb0 68#define SSD130X_SET_COM_SCAN_DIR 0xc0 69#define SSD130X_SET_DISPLAY_OFFSET 0xd3 70#define SSD130X_SET_CLOCK_FREQ 0xd5 71#define SSD130X_SET_AREA_COLOR_MODE 0xd8 72#define SSD130X_SET_PRECHARGE_PERIOD 0xd9 73#define SSD130X_SET_COM_PINS_CONFIG 0xda 74#define SSD130X_SET_VCOMH 0xdb 75 76/* ssd130x commands accessors */ 77#define SSD130X_PAGE_COL_START_MASK GENMASK(3, 0) 78#define SSD130X_PAGE_COL_START_HIGH_SET(val) FIELD_PREP(SSD130X_PAGE_COL_START_MASK, (val) >> 4) 79#define SSD130X_PAGE_COL_START_LOW_SET(val) FIELD_PREP(SSD130X_PAGE_COL_START_MASK, (val)) 80#define SSD130X_START_PAGE_ADDRESS_MASK GENMASK(2, 0) 81#define SSD130X_START_PAGE_ADDRESS_SET(val) FIELD_PREP(SSD130X_START_PAGE_ADDRESS_MASK, (val)) 82#define SSD130X_SET_COM_SCAN_DIR_MASK GENMASK(3, 3) 83#define SSD130X_SET_COM_SCAN_DIR_SET(val) FIELD_PREP(SSD130X_SET_COM_SCAN_DIR_MASK, (val)) 84#define SSD130X_SET_CLOCK_DIV_MASK GENMASK(3, 0) 85#define SSD130X_SET_CLOCK_DIV_SET(val) FIELD_PREP(SSD130X_SET_CLOCK_DIV_MASK, (val)) 86#define SSD130X_SET_CLOCK_FREQ_MASK GENMASK(7, 4) 87#define SSD130X_SET_CLOCK_FREQ_SET(val) FIELD_PREP(SSD130X_SET_CLOCK_FREQ_MASK, (val)) 88#define SSD130X_SET_PRECHARGE_PERIOD1_MASK GENMASK(3, 0) 89#define SSD130X_SET_PRECHARGE_PERIOD1_SET(val) FIELD_PREP(SSD130X_SET_PRECHARGE_PERIOD1_MASK, (val)) 90#define SSD130X_SET_PRECHARGE_PERIOD2_MASK GENMASK(7, 4) 91#define SSD130X_SET_PRECHARGE_PERIOD2_SET(val) FIELD_PREP(SSD130X_SET_PRECHARGE_PERIOD2_MASK, (val)) 92#define SSD130X_SET_COM_PINS_CONFIG1_MASK GENMASK(4, 4) 93#define SSD130X_SET_COM_PINS_CONFIG1_SET(val) FIELD_PREP(SSD130X_SET_COM_PINS_CONFIG1_MASK, (val)) 94#define SSD130X_SET_COM_PINS_CONFIG2_MASK GENMASK(5, 5) 95#define SSD130X_SET_COM_PINS_CONFIG2_SET(val) FIELD_PREP(SSD130X_SET_COM_PINS_CONFIG2_MASK, (val)) 96 97#define SSD130X_SET_ADDRESS_MODE_HORIZONTAL 0x00 98#define SSD130X_SET_ADDRESS_MODE_VERTICAL 0x01 99#define SSD130X_SET_ADDRESS_MODE_PAGE 0x02 100 101#define SSD130X_SET_AREA_COLOR_MODE_ENABLE 0x1e 102#define SSD130X_SET_AREA_COLOR_MODE_LOW_POWER 0x05 103 104/* ssd132x commands */ 105#define SSD132X_SET_COL_RANGE 0x15 106#define SSD132X_SET_DEACTIVATE_SCROLL 0x2e 107#define SSD132X_SET_ROW_RANGE 0x75 108#define SSD132X_SET_DISPLAY_START 0xa1 109#define SSD132X_SET_DISPLAY_OFFSET 0xa2 110#define SSD132X_SET_DISPLAY_NORMAL 0xa4 111#define SSD132X_SET_FUNCTION_SELECT_A 0xab 112#define SSD132X_SET_PHASE_LENGTH 0xb1 113#define SSD132X_SET_CLOCK_FREQ 0xb3 114#define SSD132X_SET_GPIO 0xb5 115#define SSD132X_SET_PRECHARGE_PERIOD 0xb6 116#define SSD132X_SET_GRAY_SCALE_TABLE 0xb8 117#define SSD132X_SELECT_DEFAULT_TABLE 0xb9 118#define SSD132X_SET_PRECHARGE_VOLTAGE 0xbc 119#define SSD130X_SET_VCOMH_VOLTAGE 0xbe 120#define SSD132X_SET_FUNCTION_SELECT_B 0xd5 121 122/* ssd133x commands */ 123#define SSD133X_SET_COL_RANGE 0x15 124#define SSD133X_SET_ROW_RANGE 0x75 125#define SSD133X_CONTRAST_A 0x81 126#define SSD133X_CONTRAST_B 0x82 127#define SSD133X_CONTRAST_C 0x83 128#define SSD133X_SET_MASTER_CURRENT 0x87 129#define SSD132X_SET_PRECHARGE_A 0x8a 130#define SSD132X_SET_PRECHARGE_B 0x8b 131#define SSD132X_SET_PRECHARGE_C 0x8c 132#define SSD133X_SET_DISPLAY_START 0xa1 133#define SSD133X_SET_DISPLAY_OFFSET 0xa2 134#define SSD133X_SET_DISPLAY_NORMAL 0xa4 135#define SSD133X_SET_MASTER_CONFIG 0xad 136#define SSD133X_POWER_SAVE_MODE 0xb0 137#define SSD133X_PHASES_PERIOD 0xb1 138#define SSD133X_SET_CLOCK_FREQ 0xb3 139#define SSD133X_SET_PRECHARGE_VOLTAGE 0xbb 140#define SSD133X_SET_VCOMH_VOLTAGE 0xbe 141 142#define MAX_CONTRAST 255 143 144const struct ssd130x_deviceinfo ssd130x_variants[] = { 145 [SH1106_ID] = { 146 .default_vcomh = 0x40, 147 .default_dclk_div = 1, 148 .default_dclk_frq = 5, 149 .default_width = 132, 150 .default_height = 64, 151 .page_mode_only = 1, 152 .family_id = SSD130X_FAMILY, 153 }, 154 [SSD1305_ID] = { 155 .default_vcomh = 0x34, 156 .default_dclk_div = 1, 157 .default_dclk_frq = 7, 158 .default_width = 132, 159 .default_height = 64, 160 .family_id = SSD130X_FAMILY, 161 }, 162 [SSD1306_ID] = { 163 .default_vcomh = 0x20, 164 .default_dclk_div = 1, 165 .default_dclk_frq = 8, 166 .need_chargepump = 1, 167 .default_width = 128, 168 .default_height = 64, 169 .family_id = SSD130X_FAMILY, 170 }, 171 [SSD1307_ID] = { 172 .default_vcomh = 0x20, 173 .default_dclk_div = 2, 174 .default_dclk_frq = 12, 175 .need_pwm = 1, 176 .default_width = 128, 177 .default_height = 39, 178 .family_id = SSD130X_FAMILY, 179 }, 180 [SSD1309_ID] = { 181 .default_vcomh = 0x34, 182 .default_dclk_div = 1, 183 .default_dclk_frq = 10, 184 .default_width = 128, 185 .default_height = 64, 186 .family_id = SSD130X_FAMILY, 187 }, 188 /* ssd132x family */ 189 [SSD1322_ID] = { 190 .default_width = 480, 191 .default_height = 128, 192 .family_id = SSD132X_FAMILY, 193 }, 194 [SSD1325_ID] = { 195 .default_width = 128, 196 .default_height = 80, 197 .family_id = SSD132X_FAMILY, 198 }, 199 [SSD1327_ID] = { 200 .default_width = 128, 201 .default_height = 128, 202 .family_id = SSD132X_FAMILY, 203 }, 204 /* ssd133x family */ 205 [SSD1331_ID] = { 206 .default_width = 96, 207 .default_height = 64, 208 .family_id = SSD133X_FAMILY, 209 } 210}; 211EXPORT_SYMBOL_NS_GPL(ssd130x_variants, DRM_SSD130X); 212 213struct ssd130x_crtc_state { 214 struct drm_crtc_state base; 215 /* Buffer to store pixels in HW format and written to the panel */ 216 u8 *data_array; 217}; 218 219struct ssd130x_plane_state { 220 struct drm_shadow_plane_state base; 221 /* Intermediate buffer to convert pixels from XRGB8888 to HW format */ 222 u8 *buffer; 223}; 224 225static inline struct ssd130x_crtc_state *to_ssd130x_crtc_state(struct drm_crtc_state *state) 226{ 227 return container_of(state, struct ssd130x_crtc_state, base); 228} 229 230static inline struct ssd130x_plane_state *to_ssd130x_plane_state(struct drm_plane_state *state) 231{ 232 return container_of(state, struct ssd130x_plane_state, base.base); 233} 234 235static inline struct ssd130x_device *drm_to_ssd130x(struct drm_device *drm) 236{ 237 return container_of(drm, struct ssd130x_device, drm); 238} 239 240/* 241 * Helper to write data (SSD13XX_DATA) to the device. 242 */ 243static int ssd130x_write_data(struct ssd130x_device *ssd130x, u8 *values, int count) 244{ 245 return regmap_bulk_write(ssd130x->regmap, SSD13XX_DATA, values, count); 246} 247 248/* 249 * Helper to write command (SSD13XX_COMMAND). The fist variadic argument 250 * is the command to write and the following are the command options. 251 * 252 * Note that the ssd13xx protocol requires each command and option to be 253 * written as a SSD13XX_COMMAND device register value. That is why a call 254 * to regmap_write(..., SSD13XX_COMMAND, ...) is done for each argument. 255 */ 256static int ssd130x_write_cmd(struct ssd130x_device *ssd130x, int count, 257 /* u8 cmd, u8 option, ... */...) 258{ 259 va_list ap; 260 u8 value; 261 int ret; 262 263 va_start(ap, count); 264 265 do { 266 value = va_arg(ap, int); 267 ret = regmap_write(ssd130x->regmap, SSD13XX_COMMAND, value); 268 if (ret) 269 goto out_end; 270 } while (--count); 271 272out_end: 273 va_end(ap); 274 275 return ret; 276} 277 278/* Set address range for horizontal/vertical addressing modes */ 279static int ssd130x_set_col_range(struct ssd130x_device *ssd130x, 280 u8 col_start, u8 cols) 281{ 282 u8 col_end = col_start + cols - 1; 283 int ret; 284 285 if (col_start == ssd130x->col_start && col_end == ssd130x->col_end) 286 return 0; 287 288 ret = ssd130x_write_cmd(ssd130x, 3, SSD130X_SET_COL_RANGE, col_start, col_end); 289 if (ret < 0) 290 return ret; 291 292 ssd130x->col_start = col_start; 293 ssd130x->col_end = col_end; 294 return 0; 295} 296 297static int ssd130x_set_page_range(struct ssd130x_device *ssd130x, 298 u8 page_start, u8 pages) 299{ 300 u8 page_end = page_start + pages - 1; 301 int ret; 302 303 if (page_start == ssd130x->page_start && page_end == ssd130x->page_end) 304 return 0; 305 306 ret = ssd130x_write_cmd(ssd130x, 3, SSD130X_SET_PAGE_RANGE, page_start, page_end); 307 if (ret < 0) 308 return ret; 309 310 ssd130x->page_start = page_start; 311 ssd130x->page_end = page_end; 312 return 0; 313} 314 315/* Set page and column start address for page addressing mode */ 316static int ssd130x_set_page_pos(struct ssd130x_device *ssd130x, 317 u8 page_start, u8 col_start) 318{ 319 int ret; 320 u32 page, col_low, col_high; 321 322 page = SSD130X_START_PAGE_ADDRESS | 323 SSD130X_START_PAGE_ADDRESS_SET(page_start); 324 col_low = SSD130X_PAGE_COL_START_LOW | 325 SSD130X_PAGE_COL_START_LOW_SET(col_start); 326 col_high = SSD130X_PAGE_COL_START_HIGH | 327 SSD130X_PAGE_COL_START_HIGH_SET(col_start); 328 ret = ssd130x_write_cmd(ssd130x, 3, page, col_low, col_high); 329 if (ret < 0) 330 return ret; 331 332 return 0; 333} 334 335static int ssd130x_pwm_enable(struct ssd130x_device *ssd130x) 336{ 337 struct device *dev = ssd130x->dev; 338 struct pwm_state pwmstate; 339 340 ssd130x->pwm = pwm_get(dev, NULL); 341 if (IS_ERR(ssd130x->pwm)) { 342 dev_err(dev, "Could not get PWM from firmware description!\n"); 343 return PTR_ERR(ssd130x->pwm); 344 } 345 346 pwm_init_state(ssd130x->pwm, &pwmstate); 347 pwm_set_relative_duty_cycle(&pwmstate, 50, 100); 348 pwm_apply_might_sleep(ssd130x->pwm, &pwmstate); 349 350 /* Enable the PWM */ 351 pwm_enable(ssd130x->pwm); 352 353 dev_dbg(dev, "Using PWM %s with a %lluns period.\n", 354 ssd130x->pwm->label, pwm_get_period(ssd130x->pwm)); 355 356 return 0; 357} 358 359static void ssd130x_reset(struct ssd130x_device *ssd130x) 360{ 361 if (!ssd130x->reset) 362 return; 363 364 /* Reset the screen */ 365 gpiod_set_value_cansleep(ssd130x->reset, 1); 366 udelay(4); 367 gpiod_set_value_cansleep(ssd130x->reset, 0); 368 udelay(4); 369} 370 371static int ssd130x_power_on(struct ssd130x_device *ssd130x) 372{ 373 struct device *dev = ssd130x->dev; 374 int ret; 375 376 ssd130x_reset(ssd130x); 377 378 ret = regulator_enable(ssd130x->vcc_reg); 379 if (ret) { 380 dev_err(dev, "Failed to enable VCC: %d\n", ret); 381 return ret; 382 } 383 384 if (ssd130x->device_info->need_pwm) { 385 ret = ssd130x_pwm_enable(ssd130x); 386 if (ret) { 387 dev_err(dev, "Failed to enable PWM: %d\n", ret); 388 regulator_disable(ssd130x->vcc_reg); 389 return ret; 390 } 391 } 392 393 return 0; 394} 395 396static void ssd130x_power_off(struct ssd130x_device *ssd130x) 397{ 398 pwm_disable(ssd130x->pwm); 399 pwm_put(ssd130x->pwm); 400 401 regulator_disable(ssd130x->vcc_reg); 402} 403 404static int ssd130x_init(struct ssd130x_device *ssd130x) 405{ 406 u32 precharge, dclk, com_invdir, compins, chargepump, seg_remap; 407 bool scan_mode; 408 int ret; 409 410 /* Set initial contrast */ 411 ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_CONTRAST, ssd130x->contrast); 412 if (ret < 0) 413 return ret; 414 415 /* Set segment re-map */ 416 seg_remap = (SSD13XX_SET_SEG_REMAP | 417 SSD13XX_SET_SEG_REMAP_SET(ssd130x->seg_remap)); 418 ret = ssd130x_write_cmd(ssd130x, 1, seg_remap); 419 if (ret < 0) 420 return ret; 421 422 /* Set COM direction */ 423 com_invdir = (SSD130X_SET_COM_SCAN_DIR | 424 SSD130X_SET_COM_SCAN_DIR_SET(ssd130x->com_invdir)); 425 ret = ssd130x_write_cmd(ssd130x, 1, com_invdir); 426 if (ret < 0) 427 return ret; 428 429 /* Set multiplex ratio value */ 430 ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_SET_MULTIPLEX_RATIO, ssd130x->height - 1); 431 if (ret < 0) 432 return ret; 433 434 /* set display offset value */ 435 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_DISPLAY_OFFSET, ssd130x->com_offset); 436 if (ret < 0) 437 return ret; 438 439 /* Set clock frequency */ 440 dclk = (SSD130X_SET_CLOCK_DIV_SET(ssd130x->dclk_div - 1) | 441 SSD130X_SET_CLOCK_FREQ_SET(ssd130x->dclk_frq)); 442 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_CLOCK_FREQ, dclk); 443 if (ret < 0) 444 return ret; 445 446 /* Set Area Color Mode ON/OFF & Low Power Display Mode */ 447 if (ssd130x->area_color_enable || ssd130x->low_power) { 448 u32 mode = 0; 449 450 if (ssd130x->area_color_enable) 451 mode |= SSD130X_SET_AREA_COLOR_MODE_ENABLE; 452 453 if (ssd130x->low_power) 454 mode |= SSD130X_SET_AREA_COLOR_MODE_LOW_POWER; 455 456 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_AREA_COLOR_MODE, mode); 457 if (ret < 0) 458 return ret; 459 } 460 461 /* Set precharge period in number of ticks from the internal clock */ 462 precharge = (SSD130X_SET_PRECHARGE_PERIOD1_SET(ssd130x->prechargep1) | 463 SSD130X_SET_PRECHARGE_PERIOD2_SET(ssd130x->prechargep2)); 464 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_PRECHARGE_PERIOD, precharge); 465 if (ret < 0) 466 return ret; 467 468 /* Set COM pins configuration */ 469 compins = BIT(1); 470 /* 471 * The COM scan mode field values are the inverse of the boolean DT 472 * property "solomon,com-seq". The value 0b means scan from COM0 to 473 * COM[N - 1] while 1b means scan from COM[N - 1] to COM0. 474 */ 475 scan_mode = !ssd130x->com_seq; 476 compins |= (SSD130X_SET_COM_PINS_CONFIG1_SET(scan_mode) | 477 SSD130X_SET_COM_PINS_CONFIG2_SET(ssd130x->com_lrremap)); 478 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_COM_PINS_CONFIG, compins); 479 if (ret < 0) 480 return ret; 481 482 /* Set VCOMH */ 483 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_VCOMH, ssd130x->vcomh); 484 if (ret < 0) 485 return ret; 486 487 /* Turn on the DC-DC Charge Pump */ 488 chargepump = BIT(4); 489 490 if (ssd130x->device_info->need_chargepump) 491 chargepump |= BIT(2); 492 493 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_CHARGE_PUMP, chargepump); 494 if (ret < 0) 495 return ret; 496 497 /* Set lookup table */ 498 if (ssd130x->lookup_table_set) { 499 int i; 500 501 ret = ssd130x_write_cmd(ssd130x, 1, SSD130X_SET_LOOKUP_TABLE); 502 if (ret < 0) 503 return ret; 504 505 for (i = 0; i < ARRAY_SIZE(ssd130x->lookup_table); i++) { 506 u8 val = ssd130x->lookup_table[i]; 507 508 if (val < 31 || val > 63) 509 dev_warn(ssd130x->dev, 510 "lookup table index %d value out of range 31 <= %d <= 63\n", 511 i, val); 512 ret = ssd130x_write_cmd(ssd130x, 1, val); 513 if (ret < 0) 514 return ret; 515 } 516 } 517 518 /* Switch to page addressing mode */ 519 if (ssd130x->page_address_mode) 520 return ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_ADDRESS_MODE, 521 SSD130X_SET_ADDRESS_MODE_PAGE); 522 523 /* Switch to horizontal addressing mode */ 524 return ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_ADDRESS_MODE, 525 SSD130X_SET_ADDRESS_MODE_HORIZONTAL); 526} 527 528static int ssd132x_init(struct ssd130x_device *ssd130x) 529{ 530 int ret; 531 532 /* Set initial contrast */ 533 ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_CONTRAST, 0x80); 534 if (ret < 0) 535 return ret; 536 537 /* Set column start and end */ 538 ret = ssd130x_write_cmd(ssd130x, 3, SSD132X_SET_COL_RANGE, 0x00, 539 ssd130x->width / SSD132X_SEGMENT_WIDTH - 1); 540 if (ret < 0) 541 return ret; 542 543 /* Set row start and end */ 544 ret = ssd130x_write_cmd(ssd130x, 3, SSD132X_SET_ROW_RANGE, 0x00, ssd130x->height - 1); 545 if (ret < 0) 546 return ret; 547 /* 548 * Horizontal Address Increment 549 * Re-map for Column Address, Nibble and COM 550 * COM Split Odd Even 551 */ 552 ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_SET_SEG_REMAP, 0x53); 553 if (ret < 0) 554 return ret; 555 556 /* Set display start and offset */ 557 ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_DISPLAY_START, 0x00); 558 if (ret < 0) 559 return ret; 560 561 ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_DISPLAY_OFFSET, 0x00); 562 if (ret < 0) 563 return ret; 564 565 /* Set display mode normal */ 566 ret = ssd130x_write_cmd(ssd130x, 1, SSD132X_SET_DISPLAY_NORMAL); 567 if (ret < 0) 568 return ret; 569 570 /* Set multiplex ratio value */ 571 ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_SET_MULTIPLEX_RATIO, ssd130x->height - 1); 572 if (ret < 0) 573 return ret; 574 575 /* Set phase length */ 576 ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_PHASE_LENGTH, 0x55); 577 if (ret < 0) 578 return ret; 579 580 /* Select default linear gray scale table */ 581 ret = ssd130x_write_cmd(ssd130x, 1, SSD132X_SELECT_DEFAULT_TABLE); 582 if (ret < 0) 583 return ret; 584 585 /* Set clock frequency */ 586 ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_CLOCK_FREQ, 0x01); 587 if (ret < 0) 588 return ret; 589 590 /* Enable internal VDD regulator */ 591 ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_FUNCTION_SELECT_A, 0x1); 592 if (ret < 0) 593 return ret; 594 595 /* Set pre-charge period */ 596 ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_PRECHARGE_PERIOD, 0x01); 597 if (ret < 0) 598 return ret; 599 600 /* Set pre-charge voltage */ 601 ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_PRECHARGE_VOLTAGE, 0x08); 602 if (ret < 0) 603 return ret; 604 605 /* Set VCOMH voltage */ 606 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_VCOMH_VOLTAGE, 0x07); 607 if (ret < 0) 608 return ret; 609 610 /* Enable second pre-charge and internal VSL */ 611 ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_FUNCTION_SELECT_B, 0x62); 612 if (ret < 0) 613 return ret; 614 615 return 0; 616} 617 618static int ssd133x_init(struct ssd130x_device *ssd130x) 619{ 620 int ret; 621 622 /* Set color A contrast */ 623 ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_CONTRAST_A, 0x91); 624 if (ret < 0) 625 return ret; 626 627 /* Set color B contrast */ 628 ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_CONTRAST_B, 0x50); 629 if (ret < 0) 630 return ret; 631 632 /* Set color C contrast */ 633 ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_CONTRAST_C, 0x7d); 634 if (ret < 0) 635 return ret; 636 637 /* Set master current */ 638 ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_MASTER_CURRENT, 0x06); 639 if (ret < 0) 640 return ret; 641 642 /* Set column start and end */ 643 ret = ssd130x_write_cmd(ssd130x, 3, SSD133X_SET_COL_RANGE, 0x00, ssd130x->width - 1); 644 if (ret < 0) 645 return ret; 646 647 /* Set row start and end */ 648 ret = ssd130x_write_cmd(ssd130x, 3, SSD133X_SET_ROW_RANGE, 0x00, ssd130x->height - 1); 649 if (ret < 0) 650 return ret; 651 652 /* 653 * Horizontal Address Increment 654 * Normal order SA,SB,SC (e.g. RGB) 655 * COM Split Odd Even 656 * 256 color format 657 */ 658 ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_SET_SEG_REMAP, 0x20); 659 if (ret < 0) 660 return ret; 661 662 /* Set display start and offset */ 663 ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_DISPLAY_START, 0x00); 664 if (ret < 0) 665 return ret; 666 667 ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_DISPLAY_OFFSET, 0x00); 668 if (ret < 0) 669 return ret; 670 671 /* Set display mode normal */ 672 ret = ssd130x_write_cmd(ssd130x, 1, SSD133X_SET_DISPLAY_NORMAL); 673 if (ret < 0) 674 return ret; 675 676 /* Set multiplex ratio value */ 677 ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_SET_MULTIPLEX_RATIO, ssd130x->height - 1); 678 if (ret < 0) 679 return ret; 680 681 /* Set master configuration */ 682 ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_MASTER_CONFIG, 0x8e); 683 if (ret < 0) 684 return ret; 685 686 /* Set power mode */ 687 ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_POWER_SAVE_MODE, 0x0b); 688 if (ret < 0) 689 return ret; 690 691 /* Set Phase 1 and 2 period */ 692 ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_PHASES_PERIOD, 0x31); 693 if (ret < 0) 694 return ret; 695 696 /* Set clock divider */ 697 ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_CLOCK_FREQ, 0xf0); 698 if (ret < 0) 699 return ret; 700 701 /* Set pre-charge A */ 702 ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_PRECHARGE_A, 0x64); 703 if (ret < 0) 704 return ret; 705 706 /* Set pre-charge B */ 707 ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_PRECHARGE_B, 0x78); 708 if (ret < 0) 709 return ret; 710 711 /* Set pre-charge C */ 712 ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_PRECHARGE_C, 0x64); 713 if (ret < 0) 714 return ret; 715 716 /* Set pre-charge level */ 717 ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_PRECHARGE_VOLTAGE, 0x3a); 718 if (ret < 0) 719 return ret; 720 721 /* Set VCOMH voltage */ 722 ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_VCOMH_VOLTAGE, 0x3e); 723 if (ret < 0) 724 return ret; 725 726 return 0; 727} 728 729static int ssd130x_update_rect(struct ssd130x_device *ssd130x, 730 struct drm_rect *rect, u8 *buf, 731 u8 *data_array) 732{ 733 unsigned int x = rect->x1; 734 unsigned int y = rect->y1; 735 unsigned int width = drm_rect_width(rect); 736 unsigned int height = drm_rect_height(rect); 737 unsigned int line_length = DIV_ROUND_UP(width, 8); 738 unsigned int page_height = SSD130X_PAGE_HEIGHT; 739 unsigned int pages = DIV_ROUND_UP(height, page_height); 740 struct drm_device *drm = &ssd130x->drm; 741 u32 array_idx = 0; 742 int ret, i, j, k; 743 744 drm_WARN_ONCE(drm, y % page_height != 0, "y must be aligned to screen page\n"); 745 746 /* 747 * The screen is divided in pages, each having a height of 8 748 * pixels, and the width of the screen. When sending a byte of 749 * data to the controller, it gives the 8 bits for the current 750 * column. I.e, the first byte are the 8 bits of the first 751 * column, then the 8 bits for the second column, etc. 752 * 753 * 754 * Representation of the screen, assuming it is 5 bits 755 * wide. Each letter-number combination is a bit that controls 756 * one pixel. 757 * 758 * A0 A1 A2 A3 A4 759 * B0 B1 B2 B3 B4 760 * C0 C1 C2 C3 C4 761 * D0 D1 D2 D3 D4 762 * E0 E1 E2 E3 E4 763 * F0 F1 F2 F3 F4 764 * G0 G1 G2 G3 G4 765 * H0 H1 H2 H3 H4 766 * 767 * If you want to update this screen, you need to send 5 bytes: 768 * (1) A0 B0 C0 D0 E0 F0 G0 H0 769 * (2) A1 B1 C1 D1 E1 F1 G1 H1 770 * (3) A2 B2 C2 D2 E2 F2 G2 H2 771 * (4) A3 B3 C3 D3 E3 F3 G3 H3 772 * (5) A4 B4 C4 D4 E4 F4 G4 H4 773 */ 774 775 if (!ssd130x->page_address_mode) { 776 u8 page_start; 777 778 /* Set address range for horizontal addressing mode */ 779 ret = ssd130x_set_col_range(ssd130x, ssd130x->col_offset + x, width); 780 if (ret < 0) 781 return ret; 782 783 page_start = ssd130x->page_offset + y / page_height; 784 ret = ssd130x_set_page_range(ssd130x, page_start, pages); 785 if (ret < 0) 786 return ret; 787 } 788 789 for (i = 0; i < pages; i++) { 790 int m = page_height; 791 792 /* Last page may be partial */ 793 if (page_height * (y / page_height + i + 1) > ssd130x->height) 794 m = ssd130x->height % page_height; 795 796 for (j = 0; j < width; j++) { 797 u8 data = 0; 798 799 for (k = 0; k < m; k++) { 800 u32 idx = (page_height * i + k) * line_length + j / 8; 801 u8 byte = buf[idx]; 802 u8 bit = (byte >> (j % 8)) & 1; 803 804 data |= bit << k; 805 } 806 data_array[array_idx++] = data; 807 } 808 809 /* 810 * In page addressing mode, the start address needs to be reset, 811 * and each page then needs to be written out separately. 812 */ 813 if (ssd130x->page_address_mode) { 814 ret = ssd130x_set_page_pos(ssd130x, 815 ssd130x->page_offset + i, 816 ssd130x->col_offset + x); 817 if (ret < 0) 818 return ret; 819 820 ret = ssd130x_write_data(ssd130x, data_array, width); 821 if (ret < 0) 822 return ret; 823 824 array_idx = 0; 825 } 826 } 827 828 /* Write out update in one go if we aren't using page addressing mode */ 829 if (!ssd130x->page_address_mode) 830 ret = ssd130x_write_data(ssd130x, data_array, width * pages); 831 832 return ret; 833} 834 835static int ssd132x_update_rect(struct ssd130x_device *ssd130x, 836 struct drm_rect *rect, u8 *buf, 837 u8 *data_array) 838{ 839 unsigned int x = rect->x1; 840 unsigned int y = rect->y1; 841 unsigned int segment_width = SSD132X_SEGMENT_WIDTH; 842 unsigned int width = drm_rect_width(rect); 843 unsigned int height = drm_rect_height(rect); 844 unsigned int columns = DIV_ROUND_UP(width, segment_width); 845 unsigned int rows = height; 846 struct drm_device *drm = &ssd130x->drm; 847 u32 array_idx = 0; 848 unsigned int i, j; 849 int ret; 850 851 drm_WARN_ONCE(drm, x % segment_width != 0, "x must be aligned to screen segment\n"); 852 853 /* 854 * The screen is divided in Segment and Common outputs, where 855 * COM0 to COM[N - 1] are the rows and SEG0 to SEG[M - 1] are 856 * the columns. 857 * 858 * Each Segment has a 4-bit pixel and each Common output has a 859 * row of pixels. When using the (default) horizontal address 860 * increment mode, each byte of data sent to the controller has 861 * two Segments (e.g: SEG0 and SEG1) that are stored in the lower 862 * and higher nibbles of a single byte representing one column. 863 * That is, the first byte are SEG0 (D0[3:0]) and SEG1 (D0[7:4]), 864 * the second byte are SEG2 (D1[3:0]) and SEG3 (D1[7:4]) and so on. 865 */ 866 867 /* Set column start and end */ 868 ret = ssd130x_write_cmd(ssd130x, 3, SSD132X_SET_COL_RANGE, x / segment_width, columns - 1); 869 if (ret < 0) 870 return ret; 871 872 /* Set row start and end */ 873 ret = ssd130x_write_cmd(ssd130x, 3, SSD132X_SET_ROW_RANGE, y, rows - 1); 874 if (ret < 0) 875 return ret; 876 877 for (i = 0; i < height; i++) { 878 /* Process pair of pixels and combine them into a single byte */ 879 for (j = 0; j < width; j += segment_width) { 880 u8 n1 = buf[i * width + j]; 881 u8 n2 = buf[i * width + j + 1]; 882 883 data_array[array_idx++] = (n2 << 4) | n1; 884 } 885 } 886 887 /* Write out update in one go since horizontal addressing mode is used */ 888 ret = ssd130x_write_data(ssd130x, data_array, columns * rows); 889 890 return ret; 891} 892 893static int ssd133x_update_rect(struct ssd130x_device *ssd130x, 894 struct drm_rect *rect, u8 *data_array, 895 unsigned int pitch) 896{ 897 unsigned int x = rect->x1; 898 unsigned int y = rect->y1; 899 unsigned int columns = drm_rect_width(rect); 900 unsigned int rows = drm_rect_height(rect); 901 int ret; 902 903 /* 904 * The screen is divided in Segment and Common outputs, where 905 * COM0 to COM[N - 1] are the rows and SEG0 to SEG[M - 1] are 906 * the columns. 907 * 908 * Each Segment has a 8-bit pixel and each Common output has a 909 * row of pixels. When using the (default) horizontal address 910 * increment mode, each byte of data sent to the controller has 911 * a Segment (e.g: SEG0). 912 * 913 * When using the 256 color depth format, each pixel contains 3 914 * sub-pixels for color A, B and C. These have 3 bit, 3 bit and 915 * 2 bits respectively. 916 */ 917 918 /* Set column start and end */ 919 ret = ssd130x_write_cmd(ssd130x, 3, SSD133X_SET_COL_RANGE, x, columns - 1); 920 if (ret < 0) 921 return ret; 922 923 /* Set row start and end */ 924 ret = ssd130x_write_cmd(ssd130x, 3, SSD133X_SET_ROW_RANGE, y, rows - 1); 925 if (ret < 0) 926 return ret; 927 928 /* Write out update in one go since horizontal addressing mode is used */ 929 ret = ssd130x_write_data(ssd130x, data_array, pitch * rows); 930 931 return ret; 932} 933 934static void ssd130x_clear_screen(struct ssd130x_device *ssd130x, u8 *data_array) 935{ 936 unsigned int pages = DIV_ROUND_UP(ssd130x->height, SSD130X_PAGE_HEIGHT); 937 unsigned int width = ssd130x->width; 938 int ret, i; 939 940 if (!ssd130x->page_address_mode) { 941 memset(data_array, 0, width * pages); 942 943 /* Set address range for horizontal addressing mode */ 944 ret = ssd130x_set_col_range(ssd130x, ssd130x->col_offset, width); 945 if (ret < 0) 946 return; 947 948 ret = ssd130x_set_page_range(ssd130x, ssd130x->page_offset, pages); 949 if (ret < 0) 950 return; 951 952 /* Write out update in one go if we aren't using page addressing mode */ 953 ssd130x_write_data(ssd130x, data_array, width * pages); 954 } else { 955 /* 956 * In page addressing mode, the start address needs to be reset, 957 * and each page then needs to be written out separately. 958 */ 959 memset(data_array, 0, width); 960 961 for (i = 0; i < pages; i++) { 962 ret = ssd130x_set_page_pos(ssd130x, 963 ssd130x->page_offset + i, 964 ssd130x->col_offset); 965 if (ret < 0) 966 return; 967 968 ret = ssd130x_write_data(ssd130x, data_array, width); 969 if (ret < 0) 970 return; 971 } 972 } 973} 974 975static void ssd132x_clear_screen(struct ssd130x_device *ssd130x, u8 *data_array) 976{ 977 unsigned int columns = DIV_ROUND_UP(ssd130x->height, SSD132X_SEGMENT_WIDTH); 978 unsigned int height = ssd130x->height; 979 980 memset(data_array, 0, columns * height); 981 982 /* Write out update in one go since horizontal addressing mode is used */ 983 ssd130x_write_data(ssd130x, data_array, columns * height); 984} 985 986static void ssd133x_clear_screen(struct ssd130x_device *ssd130x, u8 *data_array) 987{ 988 const struct drm_format_info *fi = drm_format_info(DRM_FORMAT_RGB332); 989 unsigned int pitch; 990 991 if (!fi) 992 return; 993 994 pitch = drm_format_info_min_pitch(fi, 0, ssd130x->width); 995 996 memset(data_array, 0, pitch * ssd130x->height); 997 998 /* Write out update in one go since horizontal addressing mode is used */ 999 ssd130x_write_data(ssd130x, data_array, pitch * ssd130x->height); 1000} 1001 1002static int ssd130x_fb_blit_rect(struct drm_framebuffer *fb, 1003 const struct iosys_map *vmap, 1004 struct drm_rect *rect, 1005 u8 *buf, u8 *data_array, 1006 struct drm_format_conv_state *fmtcnv_state) 1007{ 1008 struct ssd130x_device *ssd130x = drm_to_ssd130x(fb->dev); 1009 struct iosys_map dst; 1010 unsigned int dst_pitch; 1011 int ret = 0; 1012 1013 /* Align y to display page boundaries */ 1014 rect->y1 = round_down(rect->y1, SSD130X_PAGE_HEIGHT); 1015 rect->y2 = min_t(unsigned int, round_up(rect->y2, SSD130X_PAGE_HEIGHT), ssd130x->height); 1016 1017 dst_pitch = DIV_ROUND_UP(drm_rect_width(rect), 8); 1018 1019 ret = drm_gem_fb_begin_cpu_access(fb, DMA_FROM_DEVICE); 1020 if (ret) 1021 return ret; 1022 1023 iosys_map_set_vaddr(&dst, buf); 1024 drm_fb_xrgb8888_to_mono(&dst, &dst_pitch, vmap, fb, rect, fmtcnv_state); 1025 1026 drm_gem_fb_end_cpu_access(fb, DMA_FROM_DEVICE); 1027 1028 ssd130x_update_rect(ssd130x, rect, buf, data_array); 1029 1030 return ret; 1031} 1032 1033static int ssd132x_fb_blit_rect(struct drm_framebuffer *fb, 1034 const struct iosys_map *vmap, 1035 struct drm_rect *rect, u8 *buf, 1036 u8 *data_array, 1037 struct drm_format_conv_state *fmtcnv_state) 1038{ 1039 struct ssd130x_device *ssd130x = drm_to_ssd130x(fb->dev); 1040 unsigned int dst_pitch = drm_rect_width(rect); 1041 struct iosys_map dst; 1042 int ret = 0; 1043 1044 /* Align x to display segment boundaries */ 1045 rect->x1 = round_down(rect->x1, SSD132X_SEGMENT_WIDTH); 1046 rect->x2 = min_t(unsigned int, round_up(rect->x2, SSD132X_SEGMENT_WIDTH), 1047 ssd130x->width); 1048 1049 ret = drm_gem_fb_begin_cpu_access(fb, DMA_FROM_DEVICE); 1050 if (ret) 1051 return ret; 1052 1053 iosys_map_set_vaddr(&dst, buf); 1054 drm_fb_xrgb8888_to_gray8(&dst, &dst_pitch, vmap, fb, rect, fmtcnv_state); 1055 1056 drm_gem_fb_end_cpu_access(fb, DMA_FROM_DEVICE); 1057 1058 ssd132x_update_rect(ssd130x, rect, buf, data_array); 1059 1060 return ret; 1061} 1062 1063static int ssd133x_fb_blit_rect(struct drm_framebuffer *fb, 1064 const struct iosys_map *vmap, 1065 struct drm_rect *rect, u8 *data_array, 1066 struct drm_format_conv_state *fmtcnv_state) 1067{ 1068 struct ssd130x_device *ssd130x = drm_to_ssd130x(fb->dev); 1069 const struct drm_format_info *fi = drm_format_info(DRM_FORMAT_RGB332); 1070 unsigned int dst_pitch; 1071 struct iosys_map dst; 1072 int ret = 0; 1073 1074 if (!fi) 1075 return -EINVAL; 1076 1077 dst_pitch = drm_format_info_min_pitch(fi, 0, drm_rect_width(rect)); 1078 1079 ret = drm_gem_fb_begin_cpu_access(fb, DMA_FROM_DEVICE); 1080 if (ret) 1081 return ret; 1082 1083 iosys_map_set_vaddr(&dst, data_array); 1084 drm_fb_xrgb8888_to_rgb332(&dst, &dst_pitch, vmap, fb, rect, fmtcnv_state); 1085 1086 drm_gem_fb_end_cpu_access(fb, DMA_FROM_DEVICE); 1087 1088 ssd133x_update_rect(ssd130x, rect, data_array, dst_pitch); 1089 1090 return ret; 1091} 1092 1093static int ssd130x_primary_plane_atomic_check(struct drm_plane *plane, 1094 struct drm_atomic_state *state) 1095{ 1096 struct drm_device *drm = plane->dev; 1097 struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); 1098 struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); 1099 struct ssd130x_plane_state *ssd130x_state = to_ssd130x_plane_state(plane_state); 1100 struct drm_shadow_plane_state *shadow_plane_state = &ssd130x_state->base; 1101 struct drm_crtc *crtc = plane_state->crtc; 1102 struct drm_crtc_state *crtc_state = NULL; 1103 const struct drm_format_info *fi; 1104 unsigned int pitch; 1105 int ret; 1106 1107 if (crtc) 1108 crtc_state = drm_atomic_get_new_crtc_state(state, crtc); 1109 1110 ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state, 1111 DRM_PLANE_NO_SCALING, 1112 DRM_PLANE_NO_SCALING, 1113 false, false); 1114 if (ret) 1115 return ret; 1116 else if (!plane_state->visible) 1117 return 0; 1118 1119 fi = drm_format_info(DRM_FORMAT_R1); 1120 if (!fi) 1121 return -EINVAL; 1122 1123 pitch = drm_format_info_min_pitch(fi, 0, ssd130x->width); 1124 1125 if (plane_state->fb->format != fi) { 1126 void *buf; 1127 1128 /* format conversion necessary; reserve buffer */ 1129 buf = drm_format_conv_state_reserve(&shadow_plane_state->fmtcnv_state, 1130 pitch, GFP_KERNEL); 1131 if (!buf) 1132 return -ENOMEM; 1133 } 1134 1135 ssd130x_state->buffer = kcalloc(pitch, ssd130x->height, GFP_KERNEL); 1136 if (!ssd130x_state->buffer) 1137 return -ENOMEM; 1138 1139 return 0; 1140} 1141 1142static int ssd132x_primary_plane_atomic_check(struct drm_plane *plane, 1143 struct drm_atomic_state *state) 1144{ 1145 struct drm_device *drm = plane->dev; 1146 struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); 1147 struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); 1148 struct ssd130x_plane_state *ssd130x_state = to_ssd130x_plane_state(plane_state); 1149 struct drm_shadow_plane_state *shadow_plane_state = &ssd130x_state->base; 1150 struct drm_crtc *crtc = plane_state->crtc; 1151 struct drm_crtc_state *crtc_state = NULL; 1152 const struct drm_format_info *fi; 1153 unsigned int pitch; 1154 int ret; 1155 1156 if (crtc) 1157 crtc_state = drm_atomic_get_new_crtc_state(state, crtc); 1158 1159 ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state, 1160 DRM_PLANE_NO_SCALING, 1161 DRM_PLANE_NO_SCALING, 1162 false, false); 1163 if (ret) 1164 return ret; 1165 else if (!plane_state->visible) 1166 return 0; 1167 1168 fi = drm_format_info(DRM_FORMAT_R8); 1169 if (!fi) 1170 return -EINVAL; 1171 1172 pitch = drm_format_info_min_pitch(fi, 0, ssd130x->width); 1173 1174 if (plane_state->fb->format != fi) { 1175 void *buf; 1176 1177 /* format conversion necessary; reserve buffer */ 1178 buf = drm_format_conv_state_reserve(&shadow_plane_state->fmtcnv_state, 1179 pitch, GFP_KERNEL); 1180 if (!buf) 1181 return -ENOMEM; 1182 } 1183 1184 ssd130x_state->buffer = kcalloc(pitch, ssd130x->height, GFP_KERNEL); 1185 if (!ssd130x_state->buffer) 1186 return -ENOMEM; 1187 1188 return 0; 1189} 1190 1191static int ssd133x_primary_plane_atomic_check(struct drm_plane *plane, 1192 struct drm_atomic_state *state) 1193{ 1194 struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); 1195 struct drm_crtc *crtc = plane_state->crtc; 1196 struct drm_crtc_state *crtc_state = NULL; 1197 int ret; 1198 1199 if (crtc) 1200 crtc_state = drm_atomic_get_new_crtc_state(state, crtc); 1201 1202 ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state, 1203 DRM_PLANE_NO_SCALING, 1204 DRM_PLANE_NO_SCALING, 1205 false, false); 1206 if (ret) 1207 return ret; 1208 else if (!plane_state->visible) 1209 return 0; 1210 1211 return 0; 1212} 1213 1214static void ssd130x_primary_plane_atomic_update(struct drm_plane *plane, 1215 struct drm_atomic_state *state) 1216{ 1217 struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); 1218 struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane); 1219 struct drm_shadow_plane_state *shadow_plane_state = to_drm_shadow_plane_state(plane_state); 1220 struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, plane_state->crtc); 1221 struct ssd130x_crtc_state *ssd130x_crtc_state = to_ssd130x_crtc_state(crtc_state); 1222 struct ssd130x_plane_state *ssd130x_plane_state = to_ssd130x_plane_state(plane_state); 1223 struct drm_framebuffer *fb = plane_state->fb; 1224 struct drm_atomic_helper_damage_iter iter; 1225 struct drm_device *drm = plane->dev; 1226 struct drm_rect dst_clip; 1227 struct drm_rect damage; 1228 int idx; 1229 1230 if (!drm_dev_enter(drm, &idx)) 1231 return; 1232 1233 drm_atomic_helper_damage_iter_init(&iter, old_plane_state, plane_state); 1234 drm_atomic_for_each_plane_damage(&iter, &damage) { 1235 dst_clip = plane_state->dst; 1236 1237 if (!drm_rect_intersect(&dst_clip, &damage)) 1238 continue; 1239 1240 ssd130x_fb_blit_rect(fb, &shadow_plane_state->data[0], &dst_clip, 1241 ssd130x_plane_state->buffer, 1242 ssd130x_crtc_state->data_array, 1243 &shadow_plane_state->fmtcnv_state); 1244 } 1245 1246 drm_dev_exit(idx); 1247} 1248 1249static void ssd132x_primary_plane_atomic_update(struct drm_plane *plane, 1250 struct drm_atomic_state *state) 1251{ 1252 struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); 1253 struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane); 1254 struct drm_shadow_plane_state *shadow_plane_state = to_drm_shadow_plane_state(plane_state); 1255 struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, plane_state->crtc); 1256 struct ssd130x_crtc_state *ssd130x_crtc_state = to_ssd130x_crtc_state(crtc_state); 1257 struct ssd130x_plane_state *ssd130x_plane_state = to_ssd130x_plane_state(plane_state); 1258 struct drm_framebuffer *fb = plane_state->fb; 1259 struct drm_atomic_helper_damage_iter iter; 1260 struct drm_device *drm = plane->dev; 1261 struct drm_rect dst_clip; 1262 struct drm_rect damage; 1263 int idx; 1264 1265 if (!drm_dev_enter(drm, &idx)) 1266 return; 1267 1268 drm_atomic_helper_damage_iter_init(&iter, old_plane_state, plane_state); 1269 drm_atomic_for_each_plane_damage(&iter, &damage) { 1270 dst_clip = plane_state->dst; 1271 1272 if (!drm_rect_intersect(&dst_clip, &damage)) 1273 continue; 1274 1275 ssd132x_fb_blit_rect(fb, &shadow_plane_state->data[0], &dst_clip, 1276 ssd130x_plane_state->buffer, 1277 ssd130x_crtc_state->data_array, 1278 &shadow_plane_state->fmtcnv_state); 1279 } 1280 1281 drm_dev_exit(idx); 1282} 1283 1284static void ssd133x_primary_plane_atomic_update(struct drm_plane *plane, 1285 struct drm_atomic_state *state) 1286{ 1287 struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); 1288 struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane); 1289 struct drm_shadow_plane_state *shadow_plane_state = to_drm_shadow_plane_state(plane_state); 1290 struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, plane_state->crtc); 1291 struct ssd130x_crtc_state *ssd130x_crtc_state = to_ssd130x_crtc_state(crtc_state); 1292 struct drm_framebuffer *fb = plane_state->fb; 1293 struct drm_atomic_helper_damage_iter iter; 1294 struct drm_device *drm = plane->dev; 1295 struct drm_rect dst_clip; 1296 struct drm_rect damage; 1297 int idx; 1298 1299 if (!drm_dev_enter(drm, &idx)) 1300 return; 1301 1302 drm_atomic_helper_damage_iter_init(&iter, old_plane_state, plane_state); 1303 drm_atomic_for_each_plane_damage(&iter, &damage) { 1304 dst_clip = plane_state->dst; 1305 1306 if (!drm_rect_intersect(&dst_clip, &damage)) 1307 continue; 1308 1309 ssd133x_fb_blit_rect(fb, &shadow_plane_state->data[0], &dst_clip, 1310 ssd130x_crtc_state->data_array, 1311 &shadow_plane_state->fmtcnv_state); 1312 } 1313 1314 drm_dev_exit(idx); 1315} 1316 1317static void ssd130x_primary_plane_atomic_disable(struct drm_plane *plane, 1318 struct drm_atomic_state *state) 1319{ 1320 struct drm_device *drm = plane->dev; 1321 struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); 1322 struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); 1323 struct drm_crtc_state *crtc_state; 1324 struct ssd130x_crtc_state *ssd130x_crtc_state; 1325 int idx; 1326 1327 if (!plane_state->crtc) 1328 return; 1329 1330 crtc_state = drm_atomic_get_new_crtc_state(state, plane_state->crtc); 1331 ssd130x_crtc_state = to_ssd130x_crtc_state(crtc_state); 1332 1333 if (!drm_dev_enter(drm, &idx)) 1334 return; 1335 1336 ssd130x_clear_screen(ssd130x, ssd130x_crtc_state->data_array); 1337 1338 drm_dev_exit(idx); 1339} 1340 1341static void ssd132x_primary_plane_atomic_disable(struct drm_plane *plane, 1342 struct drm_atomic_state *state) 1343{ 1344 struct drm_device *drm = plane->dev; 1345 struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); 1346 struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); 1347 struct drm_crtc_state *crtc_state; 1348 struct ssd130x_crtc_state *ssd130x_crtc_state; 1349 int idx; 1350 1351 if (!plane_state->crtc) 1352 return; 1353 1354 crtc_state = drm_atomic_get_new_crtc_state(state, plane_state->crtc); 1355 ssd130x_crtc_state = to_ssd130x_crtc_state(crtc_state); 1356 1357 if (!drm_dev_enter(drm, &idx)) 1358 return; 1359 1360 ssd132x_clear_screen(ssd130x, ssd130x_crtc_state->data_array); 1361 1362 drm_dev_exit(idx); 1363} 1364 1365static void ssd133x_primary_plane_atomic_disable(struct drm_plane *plane, 1366 struct drm_atomic_state *state) 1367{ 1368 struct drm_device *drm = plane->dev; 1369 struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); 1370 struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); 1371 struct drm_crtc_state *crtc_state; 1372 struct ssd130x_crtc_state *ssd130x_crtc_state; 1373 int idx; 1374 1375 if (!plane_state->crtc) 1376 return; 1377 1378 crtc_state = drm_atomic_get_new_crtc_state(state, plane_state->crtc); 1379 ssd130x_crtc_state = to_ssd130x_crtc_state(crtc_state); 1380 1381 if (!drm_dev_enter(drm, &idx)) 1382 return; 1383 1384 ssd133x_clear_screen(ssd130x, ssd130x_crtc_state->data_array); 1385 1386 drm_dev_exit(idx); 1387} 1388 1389/* Called during init to allocate the plane's atomic state. */ 1390static void ssd130x_primary_plane_reset(struct drm_plane *plane) 1391{ 1392 struct ssd130x_plane_state *ssd130x_state; 1393 1394 WARN_ON(plane->state); 1395 1396 ssd130x_state = kzalloc(sizeof(*ssd130x_state), GFP_KERNEL); 1397 if (!ssd130x_state) 1398 return; 1399 1400 __drm_gem_reset_shadow_plane(plane, &ssd130x_state->base); 1401} 1402 1403static struct drm_plane_state *ssd130x_primary_plane_duplicate_state(struct drm_plane *plane) 1404{ 1405 struct drm_shadow_plane_state *new_shadow_plane_state; 1406 struct ssd130x_plane_state *old_ssd130x_state; 1407 struct ssd130x_plane_state *ssd130x_state; 1408 1409 if (WARN_ON(!plane->state)) 1410 return NULL; 1411 1412 old_ssd130x_state = to_ssd130x_plane_state(plane->state); 1413 ssd130x_state = kmemdup(old_ssd130x_state, sizeof(*ssd130x_state), GFP_KERNEL); 1414 if (!ssd130x_state) 1415 return NULL; 1416 1417 /* The buffer is not duplicated and is allocated in .atomic_check */ 1418 ssd130x_state->buffer = NULL; 1419 1420 new_shadow_plane_state = &ssd130x_state->base; 1421 1422 __drm_gem_duplicate_shadow_plane_state(plane, new_shadow_plane_state); 1423 1424 return &new_shadow_plane_state->base; 1425} 1426 1427static void ssd130x_primary_plane_destroy_state(struct drm_plane *plane, 1428 struct drm_plane_state *state) 1429{ 1430 struct ssd130x_plane_state *ssd130x_state = to_ssd130x_plane_state(state); 1431 1432 kfree(ssd130x_state->buffer); 1433 1434 __drm_gem_destroy_shadow_plane_state(&ssd130x_state->base); 1435 1436 kfree(ssd130x_state); 1437} 1438 1439static const struct drm_plane_helper_funcs ssd130x_primary_plane_helper_funcs[] = { 1440 [SSD130X_FAMILY] = { 1441 DRM_GEM_SHADOW_PLANE_HELPER_FUNCS, 1442 .atomic_check = ssd130x_primary_plane_atomic_check, 1443 .atomic_update = ssd130x_primary_plane_atomic_update, 1444 .atomic_disable = ssd130x_primary_plane_atomic_disable, 1445 }, 1446 [SSD132X_FAMILY] = { 1447 DRM_GEM_SHADOW_PLANE_HELPER_FUNCS, 1448 .atomic_check = ssd132x_primary_plane_atomic_check, 1449 .atomic_update = ssd132x_primary_plane_atomic_update, 1450 .atomic_disable = ssd132x_primary_plane_atomic_disable, 1451 }, 1452 [SSD133X_FAMILY] = { 1453 DRM_GEM_SHADOW_PLANE_HELPER_FUNCS, 1454 .atomic_check = ssd133x_primary_plane_atomic_check, 1455 .atomic_update = ssd133x_primary_plane_atomic_update, 1456 .atomic_disable = ssd133x_primary_plane_atomic_disable, 1457 } 1458}; 1459 1460static const struct drm_plane_funcs ssd130x_primary_plane_funcs = { 1461 .update_plane = drm_atomic_helper_update_plane, 1462 .disable_plane = drm_atomic_helper_disable_plane, 1463 .reset = ssd130x_primary_plane_reset, 1464 .atomic_duplicate_state = ssd130x_primary_plane_duplicate_state, 1465 .atomic_destroy_state = ssd130x_primary_plane_destroy_state, 1466 .destroy = drm_plane_cleanup, 1467}; 1468 1469static enum drm_mode_status ssd130x_crtc_mode_valid(struct drm_crtc *crtc, 1470 const struct drm_display_mode *mode) 1471{ 1472 struct ssd130x_device *ssd130x = drm_to_ssd130x(crtc->dev); 1473 1474 if (mode->hdisplay != ssd130x->mode.hdisplay && 1475 mode->vdisplay != ssd130x->mode.vdisplay) 1476 return MODE_ONE_SIZE; 1477 else if (mode->hdisplay != ssd130x->mode.hdisplay) 1478 return MODE_ONE_WIDTH; 1479 else if (mode->vdisplay != ssd130x->mode.vdisplay) 1480 return MODE_ONE_HEIGHT; 1481 1482 return MODE_OK; 1483} 1484 1485static int ssd130x_crtc_atomic_check(struct drm_crtc *crtc, 1486 struct drm_atomic_state *state) 1487{ 1488 struct drm_device *drm = crtc->dev; 1489 struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); 1490 struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc); 1491 struct ssd130x_crtc_state *ssd130x_state = to_ssd130x_crtc_state(crtc_state); 1492 unsigned int pages = DIV_ROUND_UP(ssd130x->height, SSD130X_PAGE_HEIGHT); 1493 int ret; 1494 1495 ret = drm_crtc_helper_atomic_check(crtc, state); 1496 if (ret) 1497 return ret; 1498 1499 ssd130x_state->data_array = kmalloc(ssd130x->width * pages, GFP_KERNEL); 1500 if (!ssd130x_state->data_array) 1501 return -ENOMEM; 1502 1503 return 0; 1504} 1505 1506static int ssd132x_crtc_atomic_check(struct drm_crtc *crtc, 1507 struct drm_atomic_state *state) 1508{ 1509 struct drm_device *drm = crtc->dev; 1510 struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); 1511 struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc); 1512 struct ssd130x_crtc_state *ssd130x_state = to_ssd130x_crtc_state(crtc_state); 1513 unsigned int columns = DIV_ROUND_UP(ssd130x->width, SSD132X_SEGMENT_WIDTH); 1514 int ret; 1515 1516 ret = drm_crtc_helper_atomic_check(crtc, state); 1517 if (ret) 1518 return ret; 1519 1520 ssd130x_state->data_array = kmalloc(columns * ssd130x->height, GFP_KERNEL); 1521 if (!ssd130x_state->data_array) 1522 return -ENOMEM; 1523 1524 return 0; 1525} 1526 1527static int ssd133x_crtc_atomic_check(struct drm_crtc *crtc, 1528 struct drm_atomic_state *state) 1529{ 1530 struct drm_device *drm = crtc->dev; 1531 struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); 1532 struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc); 1533 struct ssd130x_crtc_state *ssd130x_state = to_ssd130x_crtc_state(crtc_state); 1534 const struct drm_format_info *fi = drm_format_info(DRM_FORMAT_RGB332); 1535 unsigned int pitch; 1536 int ret; 1537 1538 if (!fi) 1539 return -EINVAL; 1540 1541 ret = drm_crtc_helper_atomic_check(crtc, state); 1542 if (ret) 1543 return ret; 1544 1545 pitch = drm_format_info_min_pitch(fi, 0, ssd130x->width); 1546 1547 ssd130x_state->data_array = kmalloc(pitch * ssd130x->height, GFP_KERNEL); 1548 if (!ssd130x_state->data_array) 1549 return -ENOMEM; 1550 1551 return 0; 1552} 1553 1554/* Called during init to allocate the CRTC's atomic state. */ 1555static void ssd130x_crtc_reset(struct drm_crtc *crtc) 1556{ 1557 struct ssd130x_crtc_state *ssd130x_state; 1558 1559 WARN_ON(crtc->state); 1560 1561 ssd130x_state = kzalloc(sizeof(*ssd130x_state), GFP_KERNEL); 1562 if (!ssd130x_state) 1563 return; 1564 1565 __drm_atomic_helper_crtc_reset(crtc, &ssd130x_state->base); 1566} 1567 1568static struct drm_crtc_state *ssd130x_crtc_duplicate_state(struct drm_crtc *crtc) 1569{ 1570 struct ssd130x_crtc_state *old_ssd130x_state; 1571 struct ssd130x_crtc_state *ssd130x_state; 1572 1573 if (WARN_ON(!crtc->state)) 1574 return NULL; 1575 1576 old_ssd130x_state = to_ssd130x_crtc_state(crtc->state); 1577 ssd130x_state = kmemdup(old_ssd130x_state, sizeof(*ssd130x_state), GFP_KERNEL); 1578 if (!ssd130x_state) 1579 return NULL; 1580 1581 /* The buffer is not duplicated and is allocated in .atomic_check */ 1582 ssd130x_state->data_array = NULL; 1583 1584 __drm_atomic_helper_crtc_duplicate_state(crtc, &ssd130x_state->base); 1585 1586 return &ssd130x_state->base; 1587} 1588 1589static void ssd130x_crtc_destroy_state(struct drm_crtc *crtc, 1590 struct drm_crtc_state *state) 1591{ 1592 struct ssd130x_crtc_state *ssd130x_state = to_ssd130x_crtc_state(state); 1593 1594 kfree(ssd130x_state->data_array); 1595 1596 __drm_atomic_helper_crtc_destroy_state(state); 1597 1598 kfree(ssd130x_state); 1599} 1600 1601/* 1602 * The CRTC is always enabled. Screen updates are performed by 1603 * the primary plane's atomic_update function. Disabling clears 1604 * the screen in the primary plane's atomic_disable function. 1605 */ 1606static const struct drm_crtc_helper_funcs ssd130x_crtc_helper_funcs[] = { 1607 [SSD130X_FAMILY] = { 1608 .mode_valid = ssd130x_crtc_mode_valid, 1609 .atomic_check = ssd130x_crtc_atomic_check, 1610 }, 1611 [SSD132X_FAMILY] = { 1612 .mode_valid = ssd130x_crtc_mode_valid, 1613 .atomic_check = ssd132x_crtc_atomic_check, 1614 }, 1615 [SSD133X_FAMILY] = { 1616 .mode_valid = ssd130x_crtc_mode_valid, 1617 .atomic_check = ssd133x_crtc_atomic_check, 1618 }, 1619}; 1620 1621static const struct drm_crtc_funcs ssd130x_crtc_funcs = { 1622 .reset = ssd130x_crtc_reset, 1623 .destroy = drm_crtc_cleanup, 1624 .set_config = drm_atomic_helper_set_config, 1625 .page_flip = drm_atomic_helper_page_flip, 1626 .atomic_duplicate_state = ssd130x_crtc_duplicate_state, 1627 .atomic_destroy_state = ssd130x_crtc_destroy_state, 1628}; 1629 1630static void ssd130x_encoder_atomic_enable(struct drm_encoder *encoder, 1631 struct drm_atomic_state *state) 1632{ 1633 struct drm_device *drm = encoder->dev; 1634 struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); 1635 int ret; 1636 1637 ret = ssd130x_power_on(ssd130x); 1638 if (ret) 1639 return; 1640 1641 ret = ssd130x_init(ssd130x); 1642 if (ret) 1643 goto power_off; 1644 1645 ssd130x_write_cmd(ssd130x, 1, SSD13XX_DISPLAY_ON); 1646 1647 backlight_enable(ssd130x->bl_dev); 1648 1649 return; 1650 1651power_off: 1652 ssd130x_power_off(ssd130x); 1653 return; 1654} 1655 1656static void ssd132x_encoder_atomic_enable(struct drm_encoder *encoder, 1657 struct drm_atomic_state *state) 1658{ 1659 struct drm_device *drm = encoder->dev; 1660 struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); 1661 int ret; 1662 1663 ret = ssd130x_power_on(ssd130x); 1664 if (ret) 1665 return; 1666 1667 ret = ssd132x_init(ssd130x); 1668 if (ret) 1669 goto power_off; 1670 1671 ssd130x_write_cmd(ssd130x, 1, SSD13XX_DISPLAY_ON); 1672 1673 backlight_enable(ssd130x->bl_dev); 1674 1675 return; 1676 1677power_off: 1678 ssd130x_power_off(ssd130x); 1679} 1680 1681static void ssd133x_encoder_atomic_enable(struct drm_encoder *encoder, 1682 struct drm_atomic_state *state) 1683{ 1684 struct drm_device *drm = encoder->dev; 1685 struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); 1686 int ret; 1687 1688 ret = ssd130x_power_on(ssd130x); 1689 if (ret) 1690 return; 1691 1692 ret = ssd133x_init(ssd130x); 1693 if (ret) 1694 goto power_off; 1695 1696 ssd130x_write_cmd(ssd130x, 1, SSD13XX_DISPLAY_ON); 1697 1698 backlight_enable(ssd130x->bl_dev); 1699 1700 return; 1701 1702power_off: 1703 ssd130x_power_off(ssd130x); 1704} 1705 1706static void ssd130x_encoder_atomic_disable(struct drm_encoder *encoder, 1707 struct drm_atomic_state *state) 1708{ 1709 struct drm_device *drm = encoder->dev; 1710 struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); 1711 1712 backlight_disable(ssd130x->bl_dev); 1713 1714 ssd130x_write_cmd(ssd130x, 1, SSD13XX_DISPLAY_OFF); 1715 1716 ssd130x_power_off(ssd130x); 1717} 1718 1719static const struct drm_encoder_helper_funcs ssd130x_encoder_helper_funcs[] = { 1720 [SSD130X_FAMILY] = { 1721 .atomic_enable = ssd130x_encoder_atomic_enable, 1722 .atomic_disable = ssd130x_encoder_atomic_disable, 1723 }, 1724 [SSD132X_FAMILY] = { 1725 .atomic_enable = ssd132x_encoder_atomic_enable, 1726 .atomic_disable = ssd130x_encoder_atomic_disable, 1727 }, 1728 [SSD133X_FAMILY] = { 1729 .atomic_enable = ssd133x_encoder_atomic_enable, 1730 .atomic_disable = ssd130x_encoder_atomic_disable, 1731 } 1732}; 1733 1734static const struct drm_encoder_funcs ssd130x_encoder_funcs = { 1735 .destroy = drm_encoder_cleanup, 1736}; 1737 1738static int ssd130x_connector_get_modes(struct drm_connector *connector) 1739{ 1740 struct ssd130x_device *ssd130x = drm_to_ssd130x(connector->dev); 1741 struct drm_display_mode *mode; 1742 struct device *dev = ssd130x->dev; 1743 1744 mode = drm_mode_duplicate(connector->dev, &ssd130x->mode); 1745 if (!mode) { 1746 dev_err(dev, "Failed to duplicated mode\n"); 1747 return 0; 1748 } 1749 1750 drm_mode_probed_add(connector, mode); 1751 drm_set_preferred_mode(connector, mode->hdisplay, mode->vdisplay); 1752 1753 /* There is only a single mode */ 1754 return 1; 1755} 1756 1757static const struct drm_connector_helper_funcs ssd130x_connector_helper_funcs = { 1758 .get_modes = ssd130x_connector_get_modes, 1759}; 1760 1761static const struct drm_connector_funcs ssd130x_connector_funcs = { 1762 .reset = drm_atomic_helper_connector_reset, 1763 .fill_modes = drm_helper_probe_single_connector_modes, 1764 .destroy = drm_connector_cleanup, 1765 .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, 1766 .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, 1767}; 1768 1769static const struct drm_mode_config_funcs ssd130x_mode_config_funcs = { 1770 .fb_create = drm_gem_fb_create_with_dirty, 1771 .atomic_check = drm_atomic_helper_check, 1772 .atomic_commit = drm_atomic_helper_commit, 1773}; 1774 1775static const uint32_t ssd130x_formats[] = { 1776 DRM_FORMAT_XRGB8888, 1777}; 1778 1779DEFINE_DRM_GEM_FOPS(ssd130x_fops); 1780 1781static const struct drm_driver ssd130x_drm_driver = { 1782 DRM_GEM_SHMEM_DRIVER_OPS, 1783 .name = DRIVER_NAME, 1784 .desc = DRIVER_DESC, 1785 .date = DRIVER_DATE, 1786 .major = DRIVER_MAJOR, 1787 .minor = DRIVER_MINOR, 1788 .driver_features = DRIVER_ATOMIC | DRIVER_GEM | DRIVER_MODESET, 1789 .fops = &ssd130x_fops, 1790}; 1791 1792static int ssd130x_update_bl(struct backlight_device *bdev) 1793{ 1794 struct ssd130x_device *ssd130x = bl_get_data(bdev); 1795 int brightness = backlight_get_brightness(bdev); 1796 int ret; 1797 1798 ssd130x->contrast = brightness; 1799 1800 ret = ssd130x_write_cmd(ssd130x, 1, SSD13XX_CONTRAST); 1801 if (ret < 0) 1802 return ret; 1803 1804 ret = ssd130x_write_cmd(ssd130x, 1, ssd130x->contrast); 1805 if (ret < 0) 1806 return ret; 1807 1808 return 0; 1809} 1810 1811static const struct backlight_ops ssd130xfb_bl_ops = { 1812 .update_status = ssd130x_update_bl, 1813}; 1814 1815static void ssd130x_parse_properties(struct ssd130x_device *ssd130x) 1816{ 1817 struct device *dev = ssd130x->dev; 1818 1819 if (device_property_read_u32(dev, "solomon,width", &ssd130x->width)) 1820 ssd130x->width = ssd130x->device_info->default_width; 1821 1822 if (device_property_read_u32(dev, "solomon,height", &ssd130x->height)) 1823 ssd130x->height = ssd130x->device_info->default_height; 1824 1825 if (device_property_read_u32(dev, "solomon,page-offset", &ssd130x->page_offset)) 1826 ssd130x->page_offset = 1; 1827 1828 if (device_property_read_u32(dev, "solomon,col-offset", &ssd130x->col_offset)) 1829 ssd130x->col_offset = 0; 1830 1831 if (device_property_read_u32(dev, "solomon,com-offset", &ssd130x->com_offset)) 1832 ssd130x->com_offset = 0; 1833 1834 if (device_property_read_u32(dev, "solomon,prechargep1", &ssd130x->prechargep1)) 1835 ssd130x->prechargep1 = 2; 1836 1837 if (device_property_read_u32(dev, "solomon,prechargep2", &ssd130x->prechargep2)) 1838 ssd130x->prechargep2 = 2; 1839 1840 if (!device_property_read_u8_array(dev, "solomon,lookup-table", 1841 ssd130x->lookup_table, 1842 ARRAY_SIZE(ssd130x->lookup_table))) 1843 ssd130x->lookup_table_set = 1; 1844 1845 ssd130x->seg_remap = !device_property_read_bool(dev, "solomon,segment-no-remap"); 1846 ssd130x->com_seq = device_property_read_bool(dev, "solomon,com-seq"); 1847 ssd130x->com_lrremap = device_property_read_bool(dev, "solomon,com-lrremap"); 1848 ssd130x->com_invdir = device_property_read_bool(dev, "solomon,com-invdir"); 1849 ssd130x->area_color_enable = 1850 device_property_read_bool(dev, "solomon,area-color-enable"); 1851 ssd130x->low_power = device_property_read_bool(dev, "solomon,low-power"); 1852 1853 ssd130x->contrast = 127; 1854 ssd130x->vcomh = ssd130x->device_info->default_vcomh; 1855 1856 /* Setup display timing */ 1857 if (device_property_read_u32(dev, "solomon,dclk-div", &ssd130x->dclk_div)) 1858 ssd130x->dclk_div = ssd130x->device_info->default_dclk_div; 1859 if (device_property_read_u32(dev, "solomon,dclk-frq", &ssd130x->dclk_frq)) 1860 ssd130x->dclk_frq = ssd130x->device_info->default_dclk_frq; 1861} 1862 1863static int ssd130x_init_modeset(struct ssd130x_device *ssd130x) 1864{ 1865 enum ssd130x_family_ids family_id = ssd130x->device_info->family_id; 1866 struct drm_display_mode *mode = &ssd130x->mode; 1867 struct device *dev = ssd130x->dev; 1868 struct drm_device *drm = &ssd130x->drm; 1869 unsigned long max_width, max_height; 1870 struct drm_plane *primary_plane; 1871 struct drm_crtc *crtc; 1872 struct drm_encoder *encoder; 1873 struct drm_connector *connector; 1874 int ret; 1875 1876 /* 1877 * Modesetting 1878 */ 1879 1880 ret = drmm_mode_config_init(drm); 1881 if (ret) { 1882 dev_err(dev, "DRM mode config init failed: %d\n", ret); 1883 return ret; 1884 } 1885 1886 mode->type = DRM_MODE_TYPE_DRIVER; 1887 mode->clock = 1; 1888 mode->hdisplay = mode->htotal = ssd130x->width; 1889 mode->hsync_start = mode->hsync_end = ssd130x->width; 1890 mode->vdisplay = mode->vtotal = ssd130x->height; 1891 mode->vsync_start = mode->vsync_end = ssd130x->height; 1892 mode->width_mm = 27; 1893 mode->height_mm = 27; 1894 1895 max_width = max_t(unsigned long, mode->hdisplay, DRM_SHADOW_PLANE_MAX_WIDTH); 1896 max_height = max_t(unsigned long, mode->vdisplay, DRM_SHADOW_PLANE_MAX_HEIGHT); 1897 1898 drm->mode_config.min_width = mode->hdisplay; 1899 drm->mode_config.max_width = max_width; 1900 drm->mode_config.min_height = mode->vdisplay; 1901 drm->mode_config.max_height = max_height; 1902 drm->mode_config.preferred_depth = 24; 1903 drm->mode_config.funcs = &ssd130x_mode_config_funcs; 1904 1905 /* Primary plane */ 1906 1907 primary_plane = &ssd130x->primary_plane; 1908 ret = drm_universal_plane_init(drm, primary_plane, 0, &ssd130x_primary_plane_funcs, 1909 ssd130x_formats, ARRAY_SIZE(ssd130x_formats), 1910 NULL, DRM_PLANE_TYPE_PRIMARY, NULL); 1911 if (ret) { 1912 dev_err(dev, "DRM primary plane init failed: %d\n", ret); 1913 return ret; 1914 } 1915 1916 drm_plane_helper_add(primary_plane, &ssd130x_primary_plane_helper_funcs[family_id]); 1917 1918 drm_plane_enable_fb_damage_clips(primary_plane); 1919 1920 /* CRTC */ 1921 1922 crtc = &ssd130x->crtc; 1923 ret = drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL, 1924 &ssd130x_crtc_funcs, NULL); 1925 if (ret) { 1926 dev_err(dev, "DRM crtc init failed: %d\n", ret); 1927 return ret; 1928 } 1929 1930 drm_crtc_helper_add(crtc, &ssd130x_crtc_helper_funcs[family_id]); 1931 1932 /* Encoder */ 1933 1934 encoder = &ssd130x->encoder; 1935 ret = drm_encoder_init(drm, encoder, &ssd130x_encoder_funcs, 1936 DRM_MODE_ENCODER_NONE, NULL); 1937 if (ret) { 1938 dev_err(dev, "DRM encoder init failed: %d\n", ret); 1939 return ret; 1940 } 1941 1942 drm_encoder_helper_add(encoder, &ssd130x_encoder_helper_funcs[family_id]); 1943 1944 encoder->possible_crtcs = drm_crtc_mask(crtc); 1945 1946 /* Connector */ 1947 1948 connector = &ssd130x->connector; 1949 ret = drm_connector_init(drm, connector, &ssd130x_connector_funcs, 1950 DRM_MODE_CONNECTOR_Unknown); 1951 if (ret) { 1952 dev_err(dev, "DRM connector init failed: %d\n", ret); 1953 return ret; 1954 } 1955 1956 drm_connector_helper_add(connector, &ssd130x_connector_helper_funcs); 1957 1958 ret = drm_connector_attach_encoder(connector, encoder); 1959 if (ret) { 1960 dev_err(dev, "DRM attach connector to encoder failed: %d\n", ret); 1961 return ret; 1962 } 1963 1964 drm_mode_config_reset(drm); 1965 1966 return 0; 1967} 1968 1969static int ssd130x_get_resources(struct ssd130x_device *ssd130x) 1970{ 1971 struct device *dev = ssd130x->dev; 1972 1973 ssd130x->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); 1974 if (IS_ERR(ssd130x->reset)) 1975 return dev_err_probe(dev, PTR_ERR(ssd130x->reset), 1976 "Failed to get reset gpio\n"); 1977 1978 ssd130x->vcc_reg = devm_regulator_get(dev, "vcc"); 1979 if (IS_ERR(ssd130x->vcc_reg)) 1980 return dev_err_probe(dev, PTR_ERR(ssd130x->vcc_reg), 1981 "Failed to get VCC regulator\n"); 1982 1983 return 0; 1984} 1985 1986struct ssd130x_device *ssd130x_probe(struct device *dev, struct regmap *regmap) 1987{ 1988 struct ssd130x_device *ssd130x; 1989 struct backlight_device *bl; 1990 struct drm_device *drm; 1991 int ret; 1992 1993 ssd130x = devm_drm_dev_alloc(dev, &ssd130x_drm_driver, 1994 struct ssd130x_device, drm); 1995 if (IS_ERR(ssd130x)) 1996 return ERR_PTR(dev_err_probe(dev, PTR_ERR(ssd130x), 1997 "Failed to allocate DRM device\n")); 1998 1999 drm = &ssd130x->drm; 2000 2001 ssd130x->dev = dev; 2002 ssd130x->regmap = regmap; 2003 ssd130x->device_info = device_get_match_data(dev); 2004 2005 if (ssd130x->device_info->page_mode_only) 2006 ssd130x->page_address_mode = 1; 2007 2008 ssd130x_parse_properties(ssd130x); 2009 2010 ret = ssd130x_get_resources(ssd130x); 2011 if (ret) 2012 return ERR_PTR(ret); 2013 2014 bl = devm_backlight_device_register(dev, dev_name(dev), dev, ssd130x, 2015 &ssd130xfb_bl_ops, NULL); 2016 if (IS_ERR(bl)) 2017 return ERR_PTR(dev_err_probe(dev, PTR_ERR(bl), 2018 "Unable to register backlight device\n")); 2019 2020 bl->props.brightness = ssd130x->contrast; 2021 bl->props.max_brightness = MAX_CONTRAST; 2022 ssd130x->bl_dev = bl; 2023 2024 ret = ssd130x_init_modeset(ssd130x); 2025 if (ret) 2026 return ERR_PTR(ret); 2027 2028 ret = drm_dev_register(drm, 0); 2029 if (ret) 2030 return ERR_PTR(dev_err_probe(dev, ret, "DRM device register failed\n")); 2031 2032 drm_fbdev_generic_setup(drm, 32); 2033 2034 return ssd130x; 2035} 2036EXPORT_SYMBOL_GPL(ssd130x_probe); 2037 2038void ssd130x_remove(struct ssd130x_device *ssd130x) 2039{ 2040 drm_dev_unplug(&ssd130x->drm); 2041 drm_atomic_helper_shutdown(&ssd130x->drm); 2042} 2043EXPORT_SYMBOL_GPL(ssd130x_remove); 2044 2045void ssd130x_shutdown(struct ssd130x_device *ssd130x) 2046{ 2047 drm_atomic_helper_shutdown(&ssd130x->drm); 2048} 2049EXPORT_SYMBOL_GPL(ssd130x_shutdown); 2050 2051MODULE_DESCRIPTION(DRIVER_DESC); 2052MODULE_AUTHOR("Javier Martinez Canillas <javierm@redhat.com>"); 2053MODULE_LICENSE("GPL v2"); 2054