1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * (C) COPYRIGHT 2012-2013 ARM Limited. All rights reserved. 4 * 5 * Parts of this file were based on sources as follows: 6 * 7 * Copyright (c) 2006-2008 Intel Corporation 8 * Copyright (c) 2007 Dave Airlie <airlied@linux.ie> 9 * Copyright (C) 2011 Texas Instruments 10 */ 11 12#include <linux/clk.h> 13#include <linux/delay.h> 14#include <linux/dma-buf.h> 15#include <linux/media-bus-format.h> 16#include <linux/of_graph.h> 17 18#include <drm/drm_fb_dma_helper.h> 19#include <drm/drm_fourcc.h> 20#include <drm/drm_framebuffer.h> 21#include <drm/drm_gem_atomic_helper.h> 22#include <drm/drm_gem_dma_helper.h> 23#include <drm/drm_vblank.h> 24 25#include "pl111_drm.h" 26 27irqreturn_t pl111_irq(int irq, void *data) 28{ 29 struct pl111_drm_dev_private *priv = data; 30 u32 irq_stat; 31 irqreturn_t status = IRQ_NONE; 32 33 irq_stat = readl(priv->regs + CLCD_PL111_MIS); 34 35 if (!irq_stat) 36 return IRQ_NONE; 37 38 if (irq_stat & CLCD_IRQ_NEXTBASE_UPDATE) { 39 drm_crtc_handle_vblank(&priv->pipe.crtc); 40 41 status = IRQ_HANDLED; 42 } 43 44 /* Clear the interrupt once done */ 45 writel(irq_stat, priv->regs + CLCD_PL111_ICR); 46 47 return status; 48} 49 50static enum drm_mode_status 51pl111_mode_valid(struct drm_simple_display_pipe *pipe, 52 const struct drm_display_mode *mode) 53{ 54 struct drm_device *drm = pipe->crtc.dev; 55 struct pl111_drm_dev_private *priv = drm->dev_private; 56 u32 cpp = DIV_ROUND_UP(priv->variant->fb_depth, 8); 57 u64 bw; 58 59 /* 60 * We use the pixelclock to also account for interlaced modes, the 61 * resulting bandwidth is in bytes per second. 62 */ 63 bw = mode->clock * 1000ULL; /* In Hz */ 64 bw = bw * mode->hdisplay * mode->vdisplay * cpp; 65 bw = div_u64(bw, mode->htotal * mode->vtotal); 66 67 /* 68 * If no bandwidth constraints, anything goes, else 69 * check if we are too fast. 70 */ 71 if (priv->memory_bw && (bw > priv->memory_bw)) { 72 DRM_DEBUG_KMS("%d x %d @ %d Hz, %d cpp, bw %llu too fast\n", 73 mode->hdisplay, mode->vdisplay, 74 mode->clock * 1000, cpp, bw); 75 76 return MODE_BAD; 77 } 78 DRM_DEBUG_KMS("%d x %d @ %d Hz, %d cpp, bw %llu bytes/s OK\n", 79 mode->hdisplay, mode->vdisplay, 80 mode->clock * 1000, cpp, bw); 81 82 return MODE_OK; 83} 84 85static int pl111_display_check(struct drm_simple_display_pipe *pipe, 86 struct drm_plane_state *pstate, 87 struct drm_crtc_state *cstate) 88{ 89 const struct drm_display_mode *mode = &cstate->mode; 90 struct drm_framebuffer *old_fb = pipe->plane.state->fb; 91 struct drm_framebuffer *fb = pstate->fb; 92 93 if (mode->hdisplay % 16) 94 return -EINVAL; 95 96 if (fb) { 97 u32 offset = drm_fb_dma_get_gem_addr(fb, pstate, 0); 98 99 /* FB base address must be dword aligned. */ 100 if (offset & 3) 101 return -EINVAL; 102 103 /* There's no pitch register -- the mode's hdisplay 104 * controls it. 105 */ 106 if (fb->pitches[0] != mode->hdisplay * fb->format->cpp[0]) 107 return -EINVAL; 108 109 /* We can't change the FB format in a flicker-free 110 * manner (and only update it during CRTC enable). 111 */ 112 if (old_fb && old_fb->format != fb->format) 113 cstate->mode_changed = true; 114 } 115 116 return 0; 117} 118 119static void pl111_display_enable(struct drm_simple_display_pipe *pipe, 120 struct drm_crtc_state *cstate, 121 struct drm_plane_state *plane_state) 122{ 123 struct drm_crtc *crtc = &pipe->crtc; 124 struct drm_plane *plane = &pipe->plane; 125 struct drm_device *drm = crtc->dev; 126 struct pl111_drm_dev_private *priv = drm->dev_private; 127 const struct drm_display_mode *mode = &cstate->mode; 128 struct drm_framebuffer *fb = plane->state->fb; 129 struct drm_connector *connector = priv->connector; 130 struct drm_bridge *bridge = priv->bridge; 131 bool grayscale = false; 132 u32 cntl; 133 u32 ppl, hsw, hfp, hbp; 134 u32 lpp, vsw, vfp, vbp; 135 u32 cpl, tim2; 136 int ret; 137 138 ret = clk_set_rate(priv->clk, mode->clock * 1000); 139 if (ret) { 140 dev_err(drm->dev, 141 "Failed to set pixel clock rate to %d: %d\n", 142 mode->clock * 1000, ret); 143 } 144 145 clk_prepare_enable(priv->clk); 146 147 ppl = (mode->hdisplay / 16) - 1; 148 hsw = mode->hsync_end - mode->hsync_start - 1; 149 hfp = mode->hsync_start - mode->hdisplay - 1; 150 hbp = mode->htotal - mode->hsync_end - 1; 151 152 lpp = mode->vdisplay - 1; 153 vsw = mode->vsync_end - mode->vsync_start - 1; 154 vfp = mode->vsync_start - mode->vdisplay; 155 vbp = mode->vtotal - mode->vsync_end; 156 157 cpl = mode->hdisplay - 1; 158 159 writel((ppl << 2) | 160 (hsw << 8) | 161 (hfp << 16) | 162 (hbp << 24), 163 priv->regs + CLCD_TIM0); 164 writel(lpp | 165 (vsw << 10) | 166 (vfp << 16) | 167 (vbp << 24), 168 priv->regs + CLCD_TIM1); 169 170 spin_lock(&priv->tim2_lock); 171 172 tim2 = readl(priv->regs + CLCD_TIM2); 173 tim2 &= (TIM2_BCD | TIM2_PCD_LO_MASK | TIM2_PCD_HI_MASK); 174 175 if (priv->variant->broken_clockdivider) 176 tim2 |= TIM2_BCD; 177 178 if (mode->flags & DRM_MODE_FLAG_NHSYNC) 179 tim2 |= TIM2_IHS; 180 181 if (mode->flags & DRM_MODE_FLAG_NVSYNC) 182 tim2 |= TIM2_IVS; 183 184 if (connector) { 185 if (connector->display_info.bus_flags & DRM_BUS_FLAG_DE_LOW) 186 tim2 |= TIM2_IOE; 187 188 if (connector->display_info.bus_flags & 189 DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE) 190 tim2 |= TIM2_IPC; 191 192 if (connector->display_info.num_bus_formats == 1 && 193 connector->display_info.bus_formats[0] == 194 MEDIA_BUS_FMT_Y8_1X8) 195 grayscale = true; 196 197 /* 198 * The AC pin bias frequency is set to max count when using 199 * grayscale so at least once in a while we will reverse 200 * polarity and get rid of any DC built up that could 201 * damage the display. 202 */ 203 if (grayscale) 204 tim2 |= TIM2_ACB_MASK; 205 } 206 207 if (bridge) { 208 const struct drm_bridge_timings *btimings = bridge->timings; 209 210 /* 211 * Here is when things get really fun. Sometimes the bridge 212 * timings are such that the signal out from PL11x is not 213 * stable before the receiving bridge (such as a dumb VGA DAC 214 * or similar) samples it. If that happens, we compensate by 215 * the only method we have: output the data on the opposite 216 * edge of the clock so it is for sure stable when it gets 217 * sampled. 218 * 219 * The PL111 manual does not contain proper timining diagrams 220 * or data for these details, but we know from experiments 221 * that the setup time is more than 3000 picoseconds (3 ns). 222 * If we have a bridge that requires the signal to be stable 223 * earlier than 3000 ps before the clock pulse, we have to 224 * output the data on the opposite edge to avoid flicker. 225 */ 226 if (btimings && btimings->setup_time_ps >= 3000) 227 tim2 ^= TIM2_IPC; 228 } 229 230 tim2 |= cpl << 16; 231 writel(tim2, priv->regs + CLCD_TIM2); 232 spin_unlock(&priv->tim2_lock); 233 234 writel(0, priv->regs + CLCD_TIM3); 235 236 /* 237 * Detect grayscale bus format. We do not support a grayscale mode 238 * toward userspace, instead we expose an RGB24 buffer and then the 239 * hardware will activate its grayscaler to convert to the grayscale 240 * format. 241 */ 242 if (grayscale) 243 cntl = CNTL_LCDEN | CNTL_LCDMONO8; 244 else 245 /* Else we assume TFT display */ 246 cntl = CNTL_LCDEN | CNTL_LCDTFT | CNTL_LCDVCOMP(1); 247 248 /* On the ST Micro variant, assume all 24 bits are connected */ 249 if (priv->variant->st_bitmux_control) 250 cntl |= CNTL_ST_CDWID_24; 251 252 /* 253 * Note that the ARM hardware's format reader takes 'r' from 254 * the low bit, while DRM formats list channels from high bit 255 * to low bit as you read left to right. The ST Micro version of 256 * the PL110 (LCDC) however uses the standard DRM format. 257 */ 258 switch (fb->format->format) { 259 case DRM_FORMAT_BGR888: 260 /* Only supported on the ST Micro variant */ 261 if (priv->variant->st_bitmux_control) 262 cntl |= CNTL_ST_LCDBPP24_PACKED | CNTL_BGR; 263 break; 264 case DRM_FORMAT_RGB888: 265 /* Only supported on the ST Micro variant */ 266 if (priv->variant->st_bitmux_control) 267 cntl |= CNTL_ST_LCDBPP24_PACKED; 268 break; 269 case DRM_FORMAT_ABGR8888: 270 case DRM_FORMAT_XBGR8888: 271 if (priv->variant->st_bitmux_control) 272 cntl |= CNTL_LCDBPP24 | CNTL_BGR; 273 else 274 cntl |= CNTL_LCDBPP24; 275 break; 276 case DRM_FORMAT_ARGB8888: 277 case DRM_FORMAT_XRGB8888: 278 if (priv->variant->st_bitmux_control) 279 cntl |= CNTL_LCDBPP24; 280 else 281 cntl |= CNTL_LCDBPP24 | CNTL_BGR; 282 break; 283 case DRM_FORMAT_BGR565: 284 if (priv->variant->is_pl110) 285 cntl |= CNTL_LCDBPP16; 286 else if (priv->variant->st_bitmux_control) 287 cntl |= CNTL_LCDBPP16 | CNTL_ST_1XBPP_565 | CNTL_BGR; 288 else 289 cntl |= CNTL_LCDBPP16_565; 290 break; 291 case DRM_FORMAT_RGB565: 292 if (priv->variant->is_pl110) 293 cntl |= CNTL_LCDBPP16 | CNTL_BGR; 294 else if (priv->variant->st_bitmux_control) 295 cntl |= CNTL_LCDBPP16 | CNTL_ST_1XBPP_565; 296 else 297 cntl |= CNTL_LCDBPP16_565 | CNTL_BGR; 298 break; 299 case DRM_FORMAT_ABGR1555: 300 case DRM_FORMAT_XBGR1555: 301 cntl |= CNTL_LCDBPP16; 302 if (priv->variant->st_bitmux_control) 303 cntl |= CNTL_ST_1XBPP_5551 | CNTL_BGR; 304 break; 305 case DRM_FORMAT_ARGB1555: 306 case DRM_FORMAT_XRGB1555: 307 cntl |= CNTL_LCDBPP16; 308 if (priv->variant->st_bitmux_control) 309 cntl |= CNTL_ST_1XBPP_5551; 310 else 311 cntl |= CNTL_BGR; 312 break; 313 case DRM_FORMAT_ABGR4444: 314 case DRM_FORMAT_XBGR4444: 315 cntl |= CNTL_LCDBPP16_444; 316 if (priv->variant->st_bitmux_control) 317 cntl |= CNTL_ST_1XBPP_444 | CNTL_BGR; 318 break; 319 case DRM_FORMAT_ARGB4444: 320 case DRM_FORMAT_XRGB4444: 321 cntl |= CNTL_LCDBPP16_444; 322 if (priv->variant->st_bitmux_control) 323 cntl |= CNTL_ST_1XBPP_444; 324 else 325 cntl |= CNTL_BGR; 326 break; 327 default: 328 WARN_ONCE(true, "Unknown FB format 0x%08x\n", 329 fb->format->format); 330 break; 331 } 332 333 /* The PL110 in Integrator/Versatile does the BGR routing externally */ 334 if (priv->variant->external_bgr) 335 cntl &= ~CNTL_BGR; 336 337 /* Power sequence: first enable and chill */ 338 writel(cntl, priv->regs + priv->ctrl); 339 340 /* 341 * We expect this delay to stabilize the contrast 342 * voltage Vee as stipulated by the manual 343 */ 344 msleep(20); 345 346 if (priv->variant_display_enable) 347 priv->variant_display_enable(drm, fb->format->format); 348 349 /* Power Up */ 350 cntl |= CNTL_LCDPWR; 351 writel(cntl, priv->regs + priv->ctrl); 352 353 if (!priv->variant->broken_vblank) 354 drm_crtc_vblank_on(crtc); 355} 356 357static void pl111_display_disable(struct drm_simple_display_pipe *pipe) 358{ 359 struct drm_crtc *crtc = &pipe->crtc; 360 struct drm_device *drm = crtc->dev; 361 struct pl111_drm_dev_private *priv = drm->dev_private; 362 u32 cntl; 363 364 if (!priv->variant->broken_vblank) 365 drm_crtc_vblank_off(crtc); 366 367 /* Power Down */ 368 cntl = readl(priv->regs + priv->ctrl); 369 if (cntl & CNTL_LCDPWR) { 370 cntl &= ~CNTL_LCDPWR; 371 writel(cntl, priv->regs + priv->ctrl); 372 } 373 374 /* 375 * We expect this delay to stabilize the contrast voltage Vee as 376 * stipulated by the manual 377 */ 378 msleep(20); 379 380 if (priv->variant_display_disable) 381 priv->variant_display_disable(drm); 382 383 /* Disable */ 384 writel(0, priv->regs + priv->ctrl); 385 386 clk_disable_unprepare(priv->clk); 387} 388 389static void pl111_display_update(struct drm_simple_display_pipe *pipe, 390 struct drm_plane_state *old_pstate) 391{ 392 struct drm_crtc *crtc = &pipe->crtc; 393 struct drm_device *drm = crtc->dev; 394 struct pl111_drm_dev_private *priv = drm->dev_private; 395 struct drm_pending_vblank_event *event = crtc->state->event; 396 struct drm_plane *plane = &pipe->plane; 397 struct drm_plane_state *pstate = plane->state; 398 struct drm_framebuffer *fb = pstate->fb; 399 400 if (fb) { 401 u32 addr = drm_fb_dma_get_gem_addr(fb, pstate, 0); 402 403 writel(addr, priv->regs + CLCD_UBAS); 404 } 405 406 if (event) { 407 crtc->state->event = NULL; 408 409 spin_lock_irq(&crtc->dev->event_lock); 410 if (crtc->state->active && drm_crtc_vblank_get(crtc) == 0) 411 drm_crtc_arm_vblank_event(crtc, event); 412 else 413 drm_crtc_send_vblank_event(crtc, event); 414 spin_unlock_irq(&crtc->dev->event_lock); 415 } 416} 417 418static int pl111_display_enable_vblank(struct drm_simple_display_pipe *pipe) 419{ 420 struct drm_crtc *crtc = &pipe->crtc; 421 struct drm_device *drm = crtc->dev; 422 struct pl111_drm_dev_private *priv = drm->dev_private; 423 424 writel(CLCD_IRQ_NEXTBASE_UPDATE, priv->regs + priv->ienb); 425 426 return 0; 427} 428 429static void pl111_display_disable_vblank(struct drm_simple_display_pipe *pipe) 430{ 431 struct drm_crtc *crtc = &pipe->crtc; 432 struct drm_device *drm = crtc->dev; 433 struct pl111_drm_dev_private *priv = drm->dev_private; 434 435 writel(0, priv->regs + priv->ienb); 436} 437 438static struct drm_simple_display_pipe_funcs pl111_display_funcs = { 439 .mode_valid = pl111_mode_valid, 440 .check = pl111_display_check, 441 .enable = pl111_display_enable, 442 .disable = pl111_display_disable, 443 .update = pl111_display_update, 444}; 445 446static int pl111_clk_div_choose_div(struct clk_hw *hw, unsigned long rate, 447 unsigned long *prate, bool set_parent) 448{ 449 int best_div = 1, div; 450 struct clk_hw *parent = clk_hw_get_parent(hw); 451 unsigned long best_prate = 0; 452 unsigned long best_diff = ~0ul; 453 int max_div = (1 << (TIM2_PCD_LO_BITS + TIM2_PCD_HI_BITS)) - 1; 454 455 for (div = 1; div < max_div; div++) { 456 unsigned long this_prate, div_rate, diff; 457 458 if (set_parent) 459 this_prate = clk_hw_round_rate(parent, rate * div); 460 else 461 this_prate = *prate; 462 div_rate = DIV_ROUND_UP_ULL(this_prate, div); 463 diff = abs(rate - div_rate); 464 465 if (diff < best_diff) { 466 best_div = div; 467 best_diff = diff; 468 best_prate = this_prate; 469 } 470 } 471 472 *prate = best_prate; 473 return best_div; 474} 475 476static long pl111_clk_div_round_rate(struct clk_hw *hw, unsigned long rate, 477 unsigned long *prate) 478{ 479 int div = pl111_clk_div_choose_div(hw, rate, prate, true); 480 481 return DIV_ROUND_UP_ULL(*prate, div); 482} 483 484static unsigned long pl111_clk_div_recalc_rate(struct clk_hw *hw, 485 unsigned long prate) 486{ 487 struct pl111_drm_dev_private *priv = 488 container_of(hw, struct pl111_drm_dev_private, clk_div); 489 u32 tim2 = readl(priv->regs + CLCD_TIM2); 490 int div; 491 492 if (tim2 & TIM2_BCD) 493 return prate; 494 495 div = tim2 & TIM2_PCD_LO_MASK; 496 div |= (tim2 & TIM2_PCD_HI_MASK) >> 497 (TIM2_PCD_HI_SHIFT - TIM2_PCD_LO_BITS); 498 div += 2; 499 500 return DIV_ROUND_UP_ULL(prate, div); 501} 502 503static int pl111_clk_div_set_rate(struct clk_hw *hw, unsigned long rate, 504 unsigned long prate) 505{ 506 struct pl111_drm_dev_private *priv = 507 container_of(hw, struct pl111_drm_dev_private, clk_div); 508 int div = pl111_clk_div_choose_div(hw, rate, &prate, false); 509 u32 tim2; 510 511 spin_lock(&priv->tim2_lock); 512 tim2 = readl(priv->regs + CLCD_TIM2); 513 tim2 &= ~(TIM2_BCD | TIM2_PCD_LO_MASK | TIM2_PCD_HI_MASK); 514 515 if (div == 1) { 516 tim2 |= TIM2_BCD; 517 } else { 518 div -= 2; 519 tim2 |= div & TIM2_PCD_LO_MASK; 520 tim2 |= (div >> TIM2_PCD_LO_BITS) << TIM2_PCD_HI_SHIFT; 521 } 522 523 writel(tim2, priv->regs + CLCD_TIM2); 524 spin_unlock(&priv->tim2_lock); 525 526 return 0; 527} 528 529static const struct clk_ops pl111_clk_div_ops = { 530 .recalc_rate = pl111_clk_div_recalc_rate, 531 .round_rate = pl111_clk_div_round_rate, 532 .set_rate = pl111_clk_div_set_rate, 533}; 534 535static int 536pl111_init_clock_divider(struct drm_device *drm) 537{ 538 struct pl111_drm_dev_private *priv = drm->dev_private; 539 struct clk *parent = devm_clk_get(drm->dev, "clcdclk"); 540 struct clk_hw *div = &priv->clk_div; 541 const char *parent_name; 542 struct clk_init_data init = { 543 .name = "pl111_div", 544 .ops = &pl111_clk_div_ops, 545 .parent_names = &parent_name, 546 .num_parents = 1, 547 .flags = CLK_SET_RATE_PARENT, 548 }; 549 int ret; 550 551 if (IS_ERR(parent)) { 552 dev_err(drm->dev, "CLCD: unable to get clcdclk.\n"); 553 return PTR_ERR(parent); 554 } 555 556 spin_lock_init(&priv->tim2_lock); 557 558 /* If the clock divider is broken, use the parent directly */ 559 if (priv->variant->broken_clockdivider) { 560 priv->clk = parent; 561 return 0; 562 } 563 parent_name = __clk_get_name(parent); 564 div->init = &init; 565 566 ret = devm_clk_hw_register(drm->dev, div); 567 568 priv->clk = div->clk; 569 return ret; 570} 571 572int pl111_display_init(struct drm_device *drm) 573{ 574 struct pl111_drm_dev_private *priv = drm->dev_private; 575 int ret; 576 577 ret = pl111_init_clock_divider(drm); 578 if (ret) 579 return ret; 580 581 if (!priv->variant->broken_vblank) { 582 pl111_display_funcs.enable_vblank = pl111_display_enable_vblank; 583 pl111_display_funcs.disable_vblank = pl111_display_disable_vblank; 584 } 585 586 ret = drm_simple_display_pipe_init(drm, &priv->pipe, 587 &pl111_display_funcs, 588 priv->variant->formats, 589 priv->variant->nformats, 590 NULL, 591 priv->connector); 592 if (ret) 593 return ret; 594 595 return 0; 596} 597