1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * Copyright �� 2019-2020 Intel Corporation 4 */ 5 6#include <linux/clk.h> 7#include <linux/delay.h> 8#include <linux/of.h> 9#include <linux/of_graph.h> 10#include <linux/mfd/syscon.h> 11#include <linux/platform_device.h> 12#include <linux/regmap.h> 13 14#include <drm/drm_atomic_helper.h> 15#include <drm/drm_bridge.h> 16#include <drm/drm_bridge_connector.h> 17#include <drm/drm_mipi_dsi.h> 18#include <drm/drm_simple_kms_helper.h> 19#include <drm/drm_print.h> 20#include <drm/drm_probe_helper.h> 21 22#include "kmb_dsi.h" 23#include "kmb_regs.h" 24 25static struct mipi_dsi_host *dsi_host; 26static struct mipi_dsi_device *dsi_device; 27static struct drm_bridge *adv_bridge; 28 29/* Default setting is 1080p, 4 lanes */ 30#define IMG_HEIGHT_LINES 1080 31#define IMG_WIDTH_PX 1920 32#define MIPI_TX_ACTIVE_LANES 4 33 34static struct mipi_tx_frame_section_cfg mipi_tx_frame0_sect_cfg = { 35 .width_pixels = IMG_WIDTH_PX, 36 .height_lines = IMG_HEIGHT_LINES, 37 .data_type = DSI_LP_DT_PPS_RGB888_24B, 38 .data_mode = MIPI_DATA_MODE1, 39 .dma_packed = 0 40}; 41 42static struct mipi_tx_frame_cfg mipitx_frame0_cfg = { 43 .sections[0] = &mipi_tx_frame0_sect_cfg, 44 .sections[1] = NULL, 45 .sections[2] = NULL, 46 .sections[3] = NULL, 47 .vsync_width = 5, 48 .v_backporch = 36, 49 .v_frontporch = 4, 50 .hsync_width = 44, 51 .h_backporch = 148, 52 .h_frontporch = 88 53}; 54 55static const struct mipi_tx_dsi_cfg mipitx_dsi_cfg = { 56 .hfp_blank_en = 0, 57 .eotp_en = 0, 58 .lpm_last_vfp_line = 0, 59 .lpm_first_vsa_line = 0, 60 .sync_pulse_eventn = DSI_VIDEO_MODE_NO_BURST_EVENT, 61 .hfp_blanking = SEND_BLANK_PACKET, 62 .hbp_blanking = SEND_BLANK_PACKET, 63 .hsa_blanking = SEND_BLANK_PACKET, 64 .v_blanking = SEND_BLANK_PACKET, 65}; 66 67static struct mipi_ctrl_cfg mipi_tx_init_cfg = { 68 .active_lanes = MIPI_TX_ACTIVE_LANES, 69 .lane_rate_mbps = MIPI_TX_LANE_DATA_RATE_MBPS, 70 .ref_clk_khz = MIPI_TX_REF_CLK_KHZ, 71 .cfg_clk_khz = MIPI_TX_CFG_CLK_KHZ, 72 .tx_ctrl_cfg = { 73 .frames[0] = &mipitx_frame0_cfg, 74 .frames[1] = NULL, 75 .frames[2] = NULL, 76 .frames[3] = NULL, 77 .tx_dsi_cfg = &mipitx_dsi_cfg, 78 .line_sync_pkt_en = 0, 79 .line_counter_active = 0, 80 .frame_counter_active = 0, 81 .tx_always_use_hact = 1, 82 .tx_hact_wait_stop = 1, 83 } 84}; 85 86struct mipi_hs_freq_range_cfg { 87 u16 default_bit_rate_mbps; 88 u8 hsfreqrange_code; 89}; 90 91struct vco_params { 92 u32 freq; 93 u32 range; 94 u32 divider; 95}; 96 97static const struct vco_params vco_table[] = { 98 {52, 0x3f, 8}, 99 {80, 0x39, 8}, 100 {105, 0x2f, 4}, 101 {160, 0x29, 4}, 102 {210, 0x1f, 2}, 103 {320, 0x19, 2}, 104 {420, 0x0f, 1}, 105 {630, 0x09, 1}, 106 {1100, 0x03, 1}, 107 {0xffff, 0x01, 1}, 108}; 109 110static const struct mipi_hs_freq_range_cfg 111mipi_hs_freq_range[MIPI_DPHY_DEFAULT_BIT_RATES] = { 112 {.default_bit_rate_mbps = 80, .hsfreqrange_code = 0x00}, 113 {.default_bit_rate_mbps = 90, .hsfreqrange_code = 0x10}, 114 {.default_bit_rate_mbps = 100, .hsfreqrange_code = 0x20}, 115 {.default_bit_rate_mbps = 110, .hsfreqrange_code = 0x30}, 116 {.default_bit_rate_mbps = 120, .hsfreqrange_code = 0x01}, 117 {.default_bit_rate_mbps = 130, .hsfreqrange_code = 0x11}, 118 {.default_bit_rate_mbps = 140, .hsfreqrange_code = 0x21}, 119 {.default_bit_rate_mbps = 150, .hsfreqrange_code = 0x31}, 120 {.default_bit_rate_mbps = 160, .hsfreqrange_code = 0x02}, 121 {.default_bit_rate_mbps = 170, .hsfreqrange_code = 0x12}, 122 {.default_bit_rate_mbps = 180, .hsfreqrange_code = 0x22}, 123 {.default_bit_rate_mbps = 190, .hsfreqrange_code = 0x32}, 124 {.default_bit_rate_mbps = 205, .hsfreqrange_code = 0x03}, 125 {.default_bit_rate_mbps = 220, .hsfreqrange_code = 0x13}, 126 {.default_bit_rate_mbps = 235, .hsfreqrange_code = 0x23}, 127 {.default_bit_rate_mbps = 250, .hsfreqrange_code = 0x33}, 128 {.default_bit_rate_mbps = 275, .hsfreqrange_code = 0x04}, 129 {.default_bit_rate_mbps = 300, .hsfreqrange_code = 0x14}, 130 {.default_bit_rate_mbps = 325, .hsfreqrange_code = 0x25}, 131 {.default_bit_rate_mbps = 350, .hsfreqrange_code = 0x35}, 132 {.default_bit_rate_mbps = 400, .hsfreqrange_code = 0x05}, 133 {.default_bit_rate_mbps = 450, .hsfreqrange_code = 0x16}, 134 {.default_bit_rate_mbps = 500, .hsfreqrange_code = 0x26}, 135 {.default_bit_rate_mbps = 550, .hsfreqrange_code = 0x37}, 136 {.default_bit_rate_mbps = 600, .hsfreqrange_code = 0x07}, 137 {.default_bit_rate_mbps = 650, .hsfreqrange_code = 0x18}, 138 {.default_bit_rate_mbps = 700, .hsfreqrange_code = 0x28}, 139 {.default_bit_rate_mbps = 750, .hsfreqrange_code = 0x39}, 140 {.default_bit_rate_mbps = 800, .hsfreqrange_code = 0x09}, 141 {.default_bit_rate_mbps = 850, .hsfreqrange_code = 0x19}, 142 {.default_bit_rate_mbps = 900, .hsfreqrange_code = 0x29}, 143 {.default_bit_rate_mbps = 1000, .hsfreqrange_code = 0x0A}, 144 {.default_bit_rate_mbps = 1050, .hsfreqrange_code = 0x1A}, 145 {.default_bit_rate_mbps = 1100, .hsfreqrange_code = 0x2A}, 146 {.default_bit_rate_mbps = 1150, .hsfreqrange_code = 0x3B}, 147 {.default_bit_rate_mbps = 1200, .hsfreqrange_code = 0x0B}, 148 {.default_bit_rate_mbps = 1250, .hsfreqrange_code = 0x1B}, 149 {.default_bit_rate_mbps = 1300, .hsfreqrange_code = 0x2B}, 150 {.default_bit_rate_mbps = 1350, .hsfreqrange_code = 0x3C}, 151 {.default_bit_rate_mbps = 1400, .hsfreqrange_code = 0x0C}, 152 {.default_bit_rate_mbps = 1450, .hsfreqrange_code = 0x1C}, 153 {.default_bit_rate_mbps = 1500, .hsfreqrange_code = 0x2C}, 154 {.default_bit_rate_mbps = 1550, .hsfreqrange_code = 0x3D}, 155 {.default_bit_rate_mbps = 1600, .hsfreqrange_code = 0x0D}, 156 {.default_bit_rate_mbps = 1650, .hsfreqrange_code = 0x1D}, 157 {.default_bit_rate_mbps = 1700, .hsfreqrange_code = 0x2E}, 158 {.default_bit_rate_mbps = 1750, .hsfreqrange_code = 0x3E}, 159 {.default_bit_rate_mbps = 1800, .hsfreqrange_code = 0x0E}, 160 {.default_bit_rate_mbps = 1850, .hsfreqrange_code = 0x1E}, 161 {.default_bit_rate_mbps = 1900, .hsfreqrange_code = 0x2F}, 162 {.default_bit_rate_mbps = 1950, .hsfreqrange_code = 0x3F}, 163 {.default_bit_rate_mbps = 2000, .hsfreqrange_code = 0x0F}, 164 {.default_bit_rate_mbps = 2050, .hsfreqrange_code = 0x40}, 165 {.default_bit_rate_mbps = 2100, .hsfreqrange_code = 0x41}, 166 {.default_bit_rate_mbps = 2150, .hsfreqrange_code = 0x42}, 167 {.default_bit_rate_mbps = 2200, .hsfreqrange_code = 0x43}, 168 {.default_bit_rate_mbps = 2250, .hsfreqrange_code = 0x44}, 169 {.default_bit_rate_mbps = 2300, .hsfreqrange_code = 0x45}, 170 {.default_bit_rate_mbps = 2350, .hsfreqrange_code = 0x46}, 171 {.default_bit_rate_mbps = 2400, .hsfreqrange_code = 0x47}, 172 {.default_bit_rate_mbps = 2450, .hsfreqrange_code = 0x48}, 173 {.default_bit_rate_mbps = 2500, .hsfreqrange_code = 0x49} 174}; 175 176static void kmb_dsi_clk_disable(struct kmb_dsi *kmb_dsi) 177{ 178 clk_disable_unprepare(kmb_dsi->clk_mipi); 179 clk_disable_unprepare(kmb_dsi->clk_mipi_ecfg); 180 clk_disable_unprepare(kmb_dsi->clk_mipi_cfg); 181} 182 183void kmb_dsi_host_unregister(struct kmb_dsi *kmb_dsi) 184{ 185 kmb_dsi_clk_disable(kmb_dsi); 186 mipi_dsi_host_unregister(kmb_dsi->host); 187} 188 189/* 190 * This DSI can only be paired with bridges that do config through i2c 191 * which is ADV 7535 in the KMB EVM 192 */ 193static ssize_t kmb_dsi_host_transfer(struct mipi_dsi_host *host, 194 const struct mipi_dsi_msg *msg) 195{ 196 return 0; 197} 198 199static int kmb_dsi_host_attach(struct mipi_dsi_host *host, 200 struct mipi_dsi_device *dev) 201{ 202 return 0; 203} 204 205static int kmb_dsi_host_detach(struct mipi_dsi_host *host, 206 struct mipi_dsi_device *dev) 207{ 208 return 0; 209} 210 211static const struct mipi_dsi_host_ops kmb_dsi_host_ops = { 212 .attach = kmb_dsi_host_attach, 213 .detach = kmb_dsi_host_detach, 214 .transfer = kmb_dsi_host_transfer, 215}; 216 217int kmb_dsi_host_bridge_init(struct device *dev) 218{ 219 struct device_node *encoder_node, *dsi_out; 220 221 /* Create and register MIPI DSI host */ 222 if (!dsi_host) { 223 dsi_host = kzalloc(sizeof(*dsi_host), GFP_KERNEL); 224 if (!dsi_host) 225 return -ENOMEM; 226 227 dsi_host->ops = &kmb_dsi_host_ops; 228 229 if (!dsi_device) { 230 dsi_device = kzalloc(sizeof(*dsi_device), GFP_KERNEL); 231 if (!dsi_device) { 232 kfree(dsi_host); 233 return -ENOMEM; 234 } 235 } 236 237 dsi_host->dev = dev; 238 mipi_dsi_host_register(dsi_host); 239 } 240 241 /* Find ADV7535 node and initialize it */ 242 dsi_out = of_graph_get_endpoint_by_regs(dev->of_node, 0, 1); 243 if (!dsi_out) { 244 DRM_ERROR("Failed to get dsi_out node info from DT\n"); 245 return -EINVAL; 246 } 247 encoder_node = of_graph_get_remote_port_parent(dsi_out); 248 if (!encoder_node) { 249 of_node_put(dsi_out); 250 DRM_ERROR("Failed to get bridge info from DT\n"); 251 return -EINVAL; 252 } 253 /* Locate drm bridge from the hdmi encoder DT node */ 254 adv_bridge = of_drm_find_bridge(encoder_node); 255 of_node_put(dsi_out); 256 of_node_put(encoder_node); 257 if (!adv_bridge) { 258 DRM_DEBUG("Wait for external bridge driver DT\n"); 259 return -EPROBE_DEFER; 260 } 261 262 return 0; 263} 264 265static u32 mipi_get_datatype_params(u32 data_type, u32 data_mode, 266 struct mipi_data_type_params *params) 267{ 268 struct mipi_data_type_params data_type_param; 269 270 switch (data_type) { 271 case DSI_LP_DT_PPS_YCBCR420_12B: 272 data_type_param.size_constraint_pixels = 2; 273 data_type_param.size_constraint_bytes = 3; 274 switch (data_mode) { 275 /* Case 0 not supported according to MDK */ 276 case 1: 277 case 2: 278 case 3: 279 data_type_param.pixels_per_pclk = 2; 280 data_type_param.bits_per_pclk = 24; 281 break; 282 default: 283 DRM_ERROR("DSI: Invalid data_mode %d\n", data_mode); 284 return -EINVAL; 285 } 286 break; 287 case DSI_LP_DT_PPS_YCBCR422_16B: 288 data_type_param.size_constraint_pixels = 2; 289 data_type_param.size_constraint_bytes = 4; 290 switch (data_mode) { 291 /* Case 0 and 1 not supported according 292 * to MDK 293 */ 294 case 2: 295 data_type_param.pixels_per_pclk = 1; 296 data_type_param.bits_per_pclk = 16; 297 break; 298 case 3: 299 data_type_param.pixels_per_pclk = 2; 300 data_type_param.bits_per_pclk = 32; 301 break; 302 default: 303 DRM_ERROR("DSI: Invalid data_mode %d\n", data_mode); 304 return -EINVAL; 305 } 306 break; 307 case DSI_LP_DT_LPPS_YCBCR422_20B: 308 case DSI_LP_DT_PPS_YCBCR422_24B: 309 data_type_param.size_constraint_pixels = 2; 310 data_type_param.size_constraint_bytes = 6; 311 switch (data_mode) { 312 /* Case 0 not supported according to MDK */ 313 case 1: 314 case 2: 315 case 3: 316 data_type_param.pixels_per_pclk = 1; 317 data_type_param.bits_per_pclk = 24; 318 break; 319 default: 320 DRM_ERROR("DSI: Invalid data_mode %d\n", data_mode); 321 return -EINVAL; 322 } 323 break; 324 case DSI_LP_DT_PPS_RGB565_16B: 325 data_type_param.size_constraint_pixels = 1; 326 data_type_param.size_constraint_bytes = 2; 327 switch (data_mode) { 328 case 0: 329 case 1: 330 data_type_param.pixels_per_pclk = 1; 331 data_type_param.bits_per_pclk = 16; 332 break; 333 case 2: 334 case 3: 335 data_type_param.pixels_per_pclk = 2; 336 data_type_param.bits_per_pclk = 32; 337 break; 338 default: 339 DRM_ERROR("DSI: Invalid data_mode %d\n", data_mode); 340 return -EINVAL; 341 } 342 break; 343 case DSI_LP_DT_PPS_RGB666_18B: 344 data_type_param.size_constraint_pixels = 4; 345 data_type_param.size_constraint_bytes = 9; 346 data_type_param.bits_per_pclk = 18; 347 data_type_param.pixels_per_pclk = 1; 348 break; 349 case DSI_LP_DT_LPPS_RGB666_18B: 350 case DSI_LP_DT_PPS_RGB888_24B: 351 data_type_param.size_constraint_pixels = 1; 352 data_type_param.size_constraint_bytes = 3; 353 data_type_param.bits_per_pclk = 24; 354 data_type_param.pixels_per_pclk = 1; 355 break; 356 case DSI_LP_DT_PPS_RGB101010_30B: 357 data_type_param.size_constraint_pixels = 4; 358 data_type_param.size_constraint_bytes = 15; 359 data_type_param.bits_per_pclk = 30; 360 data_type_param.pixels_per_pclk = 1; 361 break; 362 default: 363 DRM_ERROR("DSI: Invalid data_type %d\n", data_type); 364 return -EINVAL; 365 } 366 367 *params = data_type_param; 368 return 0; 369} 370 371static u32 compute_wc(u32 width_px, u8 size_constr_p, u8 size_constr_b) 372{ 373 /* Calculate the word count for each long packet */ 374 return (((width_px / size_constr_p) * size_constr_b) & 0xffff); 375} 376 377static u32 compute_unpacked_bytes(u32 wc, u8 bits_per_pclk) 378{ 379 /* Number of PCLK cycles needed to transfer a line 380 * with each PCLK cycle, 4 Bytes are sent through the PPL module 381 */ 382 return ((wc * 8) / bits_per_pclk) * 4; 383} 384 385static u32 mipi_tx_fg_section_cfg_regs(struct kmb_dsi *kmb_dsi, 386 u8 frame_id, u8 section, 387 u32 height_lines, u32 unpacked_bytes, 388 struct mipi_tx_frame_sect_phcfg *ph_cfg) 389{ 390 u32 cfg = 0; 391 u32 ctrl_no = MIPI_CTRL6; 392 u32 reg_adr; 393 394 /* Frame section packet header */ 395 /* Word count bits [15:0] */ 396 cfg = (ph_cfg->wc & MIPI_TX_SECT_WC_MASK) << 0; 397 398 /* Data type (bits [21:16]) */ 399 cfg |= ((ph_cfg->data_type & MIPI_TX_SECT_DT_MASK) 400 << MIPI_TX_SECT_DT_SHIFT); 401 402 /* Virtual channel (bits [23:22]) */ 403 cfg |= ((ph_cfg->vchannel & MIPI_TX_SECT_VC_MASK) 404 << MIPI_TX_SECT_VC_SHIFT); 405 406 /* Data mode (bits [24:25]) */ 407 cfg |= ((ph_cfg->data_mode & MIPI_TX_SECT_DM_MASK) 408 << MIPI_TX_SECT_DM_SHIFT); 409 if (ph_cfg->dma_packed) 410 cfg |= MIPI_TX_SECT_DMA_PACKED; 411 412 dev_dbg(kmb_dsi->dev, 413 "ctrl=%d frame_id=%d section=%d cfg=%x packed=%d\n", 414 ctrl_no, frame_id, section, cfg, ph_cfg->dma_packed); 415 kmb_write_mipi(kmb_dsi, 416 (MIPI_TXm_HS_FGn_SECTo_PH(ctrl_no, frame_id, section)), 417 cfg); 418 419 /* Unpacked bytes */ 420 421 /* There are 4 frame generators and each fg has 4 sections 422 * There are 2 registers for unpacked bytes (# bytes each 423 * section occupies in memory) 424 * REG_UNPACKED_BYTES0: [15:0]-BYTES0, [31:16]-BYTES1 425 * REG_UNPACKED_BYTES1: [15:0]-BYTES2, [31:16]-BYTES3 426 */ 427 reg_adr = 428 MIPI_TXm_HS_FGn_SECT_UNPACKED_BYTES0(ctrl_no, 429 frame_id) + (section / 2) * 4; 430 kmb_write_bits_mipi(kmb_dsi, reg_adr, (section % 2) * 16, 16, 431 unpacked_bytes); 432 dev_dbg(kmb_dsi->dev, 433 "unpacked_bytes = %d, wordcount = %d\n", unpacked_bytes, 434 ph_cfg->wc); 435 436 /* Line config */ 437 reg_adr = MIPI_TXm_HS_FGn_SECTo_LINE_CFG(ctrl_no, frame_id, section); 438 kmb_write_mipi(kmb_dsi, reg_adr, height_lines); 439 return 0; 440} 441 442static u32 mipi_tx_fg_section_cfg(struct kmb_dsi *kmb_dsi, 443 u8 frame_id, u8 section, 444 struct mipi_tx_frame_section_cfg *frame_scfg, 445 u32 *bits_per_pclk, u32 *wc) 446{ 447 u32 ret = 0; 448 u32 unpacked_bytes; 449 struct mipi_data_type_params data_type_parameters; 450 struct mipi_tx_frame_sect_phcfg ph_cfg; 451 452 ret = mipi_get_datatype_params(frame_scfg->data_type, 453 frame_scfg->data_mode, 454 &data_type_parameters); 455 if (ret) 456 return ret; 457 458 /* Packet width has to be a multiple of the minimum packet width 459 * (in pixels) set for each data type 460 */ 461 if (frame_scfg->width_pixels % 462 data_type_parameters.size_constraint_pixels != 0) 463 return -EINVAL; 464 465 *wc = compute_wc(frame_scfg->width_pixels, 466 data_type_parameters.size_constraint_pixels, 467 data_type_parameters.size_constraint_bytes); 468 unpacked_bytes = compute_unpacked_bytes(*wc, 469 data_type_parameters.bits_per_pclk); 470 ph_cfg.wc = *wc; 471 ph_cfg.data_mode = frame_scfg->data_mode; 472 ph_cfg.data_type = frame_scfg->data_type; 473 ph_cfg.dma_packed = frame_scfg->dma_packed; 474 ph_cfg.vchannel = frame_id; 475 476 mipi_tx_fg_section_cfg_regs(kmb_dsi, frame_id, section, 477 frame_scfg->height_lines, 478 unpacked_bytes, &ph_cfg); 479 480 /* Caller needs bits_per_clk for additional caluclations */ 481 *bits_per_pclk = data_type_parameters.bits_per_pclk; 482 483 return 0; 484} 485 486#define CLK_DIFF_LOW 50 487#define CLK_DIFF_HI 60 488#define SYSCLK_500 500 489 490static void mipi_tx_fg_cfg_regs(struct kmb_dsi *kmb_dsi, u8 frame_gen, 491 struct mipi_tx_frame_timing_cfg *fg_cfg) 492{ 493 u32 sysclk; 494 u32 ppl_llp_ratio; 495 u32 ctrl_no = MIPI_CTRL6, reg_adr, val, offset; 496 497 /* 500 Mhz system clock minus 50 to account for the difference in 498 * MIPI clock speed in RTL tests 499 */ 500 if (kmb_dsi->sys_clk_mhz == SYSCLK_500) { 501 sysclk = kmb_dsi->sys_clk_mhz - CLK_DIFF_LOW; 502 } else { 503 /* 700 Mhz clk*/ 504 sysclk = kmb_dsi->sys_clk_mhz - CLK_DIFF_HI; 505 } 506 507 /* PPL-Pixel Packing Layer, LLP-Low Level Protocol 508 * Frame genartor timing parameters are clocked on the system clock, 509 * whereas as the equivalent parameters in the LLP blocks are clocked 510 * on LLP Tx clock from the D-PHY - BYTE clock 511 */ 512 513 /* Multiply by 1000 to maintain precision */ 514 ppl_llp_ratio = ((fg_cfg->bpp / 8) * sysclk * 1000) / 515 ((fg_cfg->lane_rate_mbps / 8) * fg_cfg->active_lanes); 516 517 dev_dbg(kmb_dsi->dev, "ppl_llp_ratio=%d\n", ppl_llp_ratio); 518 dev_dbg(kmb_dsi->dev, "bpp=%d sysclk=%d lane-rate=%d active-lanes=%d\n", 519 fg_cfg->bpp, sysclk, fg_cfg->lane_rate_mbps, 520 fg_cfg->active_lanes); 521 522 /* Frame generator number of lines */ 523 reg_adr = MIPI_TXm_HS_FGn_NUM_LINES(ctrl_no, frame_gen); 524 kmb_write_mipi(kmb_dsi, reg_adr, fg_cfg->v_active); 525 526 /* vsync width 527 * There are 2 registers for vsync width (VSA in lines for 528 * channels 0-3) 529 * REG_VSYNC_WIDTH0: [15:0]-VSA for channel0, [31:16]-VSA for channel1 530 * REG_VSYNC_WIDTH1: [15:0]-VSA for channel2, [31:16]-VSA for channel3 531 */ 532 offset = (frame_gen % 2) * 16; 533 reg_adr = MIPI_TXm_HS_VSYNC_WIDTHn(ctrl_no, frame_gen / 2); 534 kmb_write_bits_mipi(kmb_dsi, reg_adr, offset, 16, fg_cfg->vsync_width); 535 536 /* vertical backporch (vbp) */ 537 reg_adr = MIPI_TXm_HS_V_BACKPORCHESn(ctrl_no, frame_gen / 2); 538 kmb_write_bits_mipi(kmb_dsi, reg_adr, offset, 16, fg_cfg->v_backporch); 539 540 /* vertical frontporch (vfp) */ 541 reg_adr = MIPI_TXm_HS_V_FRONTPORCHESn(ctrl_no, frame_gen / 2); 542 kmb_write_bits_mipi(kmb_dsi, reg_adr, offset, 16, fg_cfg->v_frontporch); 543 544 /* vertical active (vactive) */ 545 reg_adr = MIPI_TXm_HS_V_ACTIVEn(ctrl_no, frame_gen / 2); 546 kmb_write_bits_mipi(kmb_dsi, reg_adr, offset, 16, fg_cfg->v_active); 547 548 /* hsync width */ 549 reg_adr = MIPI_TXm_HS_HSYNC_WIDTHn(ctrl_no, frame_gen); 550 kmb_write_mipi(kmb_dsi, reg_adr, 551 (fg_cfg->hsync_width * ppl_llp_ratio) / 1000); 552 553 /* horizontal backporch (hbp) */ 554 reg_adr = MIPI_TXm_HS_H_BACKPORCHn(ctrl_no, frame_gen); 555 kmb_write_mipi(kmb_dsi, reg_adr, 556 (fg_cfg->h_backporch * ppl_llp_ratio) / 1000); 557 558 /* horizontal frontporch (hfp) */ 559 reg_adr = MIPI_TXm_HS_H_FRONTPORCHn(ctrl_no, frame_gen); 560 kmb_write_mipi(kmb_dsi, reg_adr, 561 (fg_cfg->h_frontporch * ppl_llp_ratio) / 1000); 562 563 /* horizontal active (ha) */ 564 reg_adr = MIPI_TXm_HS_H_ACTIVEn(ctrl_no, frame_gen); 565 566 /* convert h_active which is wc in bytes to cycles */ 567 val = (fg_cfg->h_active * sysclk * 1000) / 568 ((fg_cfg->lane_rate_mbps / 8) * fg_cfg->active_lanes); 569 val /= 1000; 570 kmb_write_mipi(kmb_dsi, reg_adr, val); 571 572 /* llp hsync width */ 573 reg_adr = MIPI_TXm_HS_LLP_HSYNC_WIDTHn(ctrl_no, frame_gen); 574 kmb_write_mipi(kmb_dsi, reg_adr, fg_cfg->hsync_width * (fg_cfg->bpp / 8)); 575 576 /* llp h backporch */ 577 reg_adr = MIPI_TXm_HS_LLP_H_BACKPORCHn(ctrl_no, frame_gen); 578 kmb_write_mipi(kmb_dsi, reg_adr, fg_cfg->h_backporch * (fg_cfg->bpp / 8)); 579 580 /* llp h frontporch */ 581 reg_adr = MIPI_TXm_HS_LLP_H_FRONTPORCHn(ctrl_no, frame_gen); 582 kmb_write_mipi(kmb_dsi, reg_adr, 583 fg_cfg->h_frontporch * (fg_cfg->bpp / 8)); 584} 585 586static void mipi_tx_fg_cfg(struct kmb_dsi *kmb_dsi, u8 frame_gen, 587 u8 active_lanes, u32 bpp, u32 wc, 588 u32 lane_rate_mbps, struct mipi_tx_frame_cfg *fg_cfg) 589{ 590 u32 i, fg_num_lines = 0; 591 struct mipi_tx_frame_timing_cfg fg_t_cfg; 592 593 /* Calculate the total frame generator number of 594 * lines based on it's active sections 595 */ 596 for (i = 0; i < MIPI_TX_FRAME_GEN_SECTIONS; i++) { 597 if (fg_cfg->sections[i]) 598 fg_num_lines += fg_cfg->sections[i]->height_lines; 599 } 600 601 fg_t_cfg.bpp = bpp; 602 fg_t_cfg.lane_rate_mbps = lane_rate_mbps; 603 fg_t_cfg.hsync_width = fg_cfg->hsync_width; 604 fg_t_cfg.h_backporch = fg_cfg->h_backporch; 605 fg_t_cfg.h_frontporch = fg_cfg->h_frontporch; 606 fg_t_cfg.h_active = wc; 607 fg_t_cfg.vsync_width = fg_cfg->vsync_width; 608 fg_t_cfg.v_backporch = fg_cfg->v_backporch; 609 fg_t_cfg.v_frontporch = fg_cfg->v_frontporch; 610 fg_t_cfg.v_active = fg_num_lines; 611 fg_t_cfg.active_lanes = active_lanes; 612 613 /* Apply frame generator timing setting */ 614 mipi_tx_fg_cfg_regs(kmb_dsi, frame_gen, &fg_t_cfg); 615} 616 617static void mipi_tx_multichannel_fifo_cfg(struct kmb_dsi *kmb_dsi, 618 u8 active_lanes, u8 vchannel_id) 619{ 620 u32 fifo_size, fifo_rthreshold; 621 u32 ctrl_no = MIPI_CTRL6; 622 623 /* Clear all mc fifo channel sizes and thresholds */ 624 kmb_write_mipi(kmb_dsi, MIPI_TX_HS_MC_FIFO_CTRL_EN, 0); 625 kmb_write_mipi(kmb_dsi, MIPI_TX_HS_MC_FIFO_CHAN_ALLOC0, 0); 626 kmb_write_mipi(kmb_dsi, MIPI_TX_HS_MC_FIFO_CHAN_ALLOC1, 0); 627 kmb_write_mipi(kmb_dsi, MIPI_TX_HS_MC_FIFO_RTHRESHOLD0, 0); 628 kmb_write_mipi(kmb_dsi, MIPI_TX_HS_MC_FIFO_RTHRESHOLD1, 0); 629 630 fifo_size = ((active_lanes > MIPI_D_LANES_PER_DPHY) ? 631 MIPI_CTRL_4LANE_MAX_MC_FIFO_LOC : 632 MIPI_CTRL_2LANE_MAX_MC_FIFO_LOC) - 1; 633 634 /* MC fifo size for virtual channels 0-3 635 * REG_MC_FIFO_CHAN_ALLOC0: [8:0]-channel0, [24:16]-channel1 636 * REG_MC_FIFO_CHAN_ALLOC1: [8:0]-2, [24:16]-channel3 637 */ 638 SET_MC_FIFO_CHAN_ALLOC(kmb_dsi, ctrl_no, vchannel_id, fifo_size); 639 640 /* Set threshold to half the fifo size, actual size=size*16 */ 641 fifo_rthreshold = ((fifo_size) * 8) & BIT_MASK_16; 642 SET_MC_FIFO_RTHRESHOLD(kmb_dsi, ctrl_no, vchannel_id, fifo_rthreshold); 643 644 /* Enable the MC FIFO channel corresponding to the Virtual Channel */ 645 kmb_set_bit_mipi(kmb_dsi, MIPI_TXm_HS_MC_FIFO_CTRL_EN(ctrl_no), 646 vchannel_id); 647} 648 649static void mipi_tx_ctrl_cfg(struct kmb_dsi *kmb_dsi, u8 fg_id, 650 struct mipi_ctrl_cfg *ctrl_cfg) 651{ 652 u32 sync_cfg = 0, ctrl = 0, fg_en; 653 u32 ctrl_no = MIPI_CTRL6; 654 655 /* MIPI_TX_HS_SYNC_CFG */ 656 if (ctrl_cfg->tx_ctrl_cfg.line_sync_pkt_en) 657 sync_cfg |= LINE_SYNC_PKT_ENABLE; 658 if (ctrl_cfg->tx_ctrl_cfg.frame_counter_active) 659 sync_cfg |= FRAME_COUNTER_ACTIVE; 660 if (ctrl_cfg->tx_ctrl_cfg.line_counter_active) 661 sync_cfg |= LINE_COUNTER_ACTIVE; 662 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->v_blanking) 663 sync_cfg |= DSI_V_BLANKING; 664 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->hsa_blanking) 665 sync_cfg |= DSI_HSA_BLANKING; 666 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->hbp_blanking) 667 sync_cfg |= DSI_HBP_BLANKING; 668 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->hfp_blanking) 669 sync_cfg |= DSI_HFP_BLANKING; 670 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->sync_pulse_eventn) 671 sync_cfg |= DSI_SYNC_PULSE_EVENTN; 672 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->lpm_first_vsa_line) 673 sync_cfg |= DSI_LPM_FIRST_VSA_LINE; 674 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->lpm_last_vfp_line) 675 sync_cfg |= DSI_LPM_LAST_VFP_LINE; 676 677 /* Enable frame generator */ 678 fg_en = 1 << fg_id; 679 sync_cfg |= FRAME_GEN_EN(fg_en); 680 681 if (ctrl_cfg->tx_ctrl_cfg.tx_always_use_hact) 682 sync_cfg |= ALWAYS_USE_HACT(fg_en); 683 if (ctrl_cfg->tx_ctrl_cfg.tx_hact_wait_stop) 684 sync_cfg |= HACT_WAIT_STOP(fg_en); 685 686 dev_dbg(kmb_dsi->dev, "sync_cfg=%d fg_en=%d\n", sync_cfg, fg_en); 687 688 /* MIPI_TX_HS_CTRL */ 689 690 /* type:DSI, source:LCD */ 691 ctrl = HS_CTRL_EN | TX_SOURCE; 692 ctrl |= LCD_VC(fg_id); 693 ctrl |= ACTIVE_LANES(ctrl_cfg->active_lanes - 1); 694 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->eotp_en) 695 ctrl |= DSI_EOTP_EN; 696 if (ctrl_cfg->tx_ctrl_cfg.tx_dsi_cfg->hfp_blank_en) 697 ctrl |= DSI_CMD_HFP_EN; 698 699 /*67 ns stop time */ 700 ctrl |= HSEXIT_CNT(0x43); 701 702 kmb_write_mipi(kmb_dsi, MIPI_TXm_HS_SYNC_CFG(ctrl_no), sync_cfg); 703 kmb_write_mipi(kmb_dsi, MIPI_TXm_HS_CTRL(ctrl_no), ctrl); 704} 705 706static u32 mipi_tx_init_cntrl(struct kmb_dsi *kmb_dsi, 707 struct mipi_ctrl_cfg *ctrl_cfg) 708{ 709 u32 ret = 0; 710 u8 active_vchannels = 0; 711 u8 frame_id, sect; 712 u32 bits_per_pclk = 0; 713 u32 word_count = 0; 714 struct mipi_tx_frame_cfg *frame; 715 716 /* This is the order to initialize MIPI TX: 717 * 1. set frame section parameters 718 * 2. set frame specific parameters 719 * 3. connect lcd to mipi 720 * 4. multi channel fifo cfg 721 * 5. set mipitxcctrlcfg 722 */ 723 724 for (frame_id = 0; frame_id < 4; frame_id++) { 725 frame = ctrl_cfg->tx_ctrl_cfg.frames[frame_id]; 726 727 /* Find valid frame, assume only one valid frame */ 728 if (!frame) 729 continue; 730 731 /* Frame Section configuration */ 732 /* TODO - assume there is only one valid section in a frame, 733 * so bits_per_pclk and word_count are only set once 734 */ 735 for (sect = 0; sect < MIPI_CTRL_VIRTUAL_CHANNELS; sect++) { 736 if (!frame->sections[sect]) 737 continue; 738 739 ret = mipi_tx_fg_section_cfg(kmb_dsi, frame_id, sect, 740 frame->sections[sect], 741 &bits_per_pclk, 742 &word_count); 743 if (ret) 744 return ret; 745 } 746 747 /* Set frame specific parameters */ 748 mipi_tx_fg_cfg(kmb_dsi, frame_id, ctrl_cfg->active_lanes, 749 bits_per_pclk, word_count, 750 ctrl_cfg->lane_rate_mbps, frame); 751 752 active_vchannels++; 753 754 /* Stop iterating as only one virtual channel 755 * shall be used for LCD connection 756 */ 757 break; 758 } 759 760 if (active_vchannels == 0) 761 return -EINVAL; 762 /* Multi-Channel FIFO Configuration */ 763 mipi_tx_multichannel_fifo_cfg(kmb_dsi, ctrl_cfg->active_lanes, frame_id); 764 765 /* Frame Generator Enable */ 766 mipi_tx_ctrl_cfg(kmb_dsi, frame_id, ctrl_cfg); 767 768 return ret; 769} 770 771static void test_mode_send(struct kmb_dsi *kmb_dsi, u32 dphy_no, 772 u32 test_code, u32 test_data) 773{ 774 /* Steps to send test code: 775 * - set testclk HIGH 776 * - set testdin with test code 777 * - set testen HIGH 778 * - set testclk LOW 779 * - set testen LOW 780 */ 781 782 /* Set testclk high */ 783 SET_DPHY_TEST_CTRL1_CLK(kmb_dsi, dphy_no); 784 785 /* Set testdin */ 786 SET_TEST_DIN0_3(kmb_dsi, dphy_no, test_code); 787 788 /* Set testen high */ 789 SET_DPHY_TEST_CTRL1_EN(kmb_dsi, dphy_no); 790 791 /* Set testclk low */ 792 CLR_DPHY_TEST_CTRL1_CLK(kmb_dsi, dphy_no); 793 794 /* Set testen low */ 795 CLR_DPHY_TEST_CTRL1_EN(kmb_dsi, dphy_no); 796 797 if (test_code) { 798 /* Steps to send test data: 799 * - set testen LOW 800 * - set testclk LOW 801 * - set testdin with data 802 * - set testclk HIGH 803 */ 804 805 /* Set testen low */ 806 CLR_DPHY_TEST_CTRL1_EN(kmb_dsi, dphy_no); 807 808 /* Set testclk low */ 809 CLR_DPHY_TEST_CTRL1_CLK(kmb_dsi, dphy_no); 810 811 /* Set data in testdin */ 812 kmb_write_mipi(kmb_dsi, 813 DPHY_TEST_DIN0_3 + ((dphy_no / 0x4) * 0x4), 814 test_data << ((dphy_no % 4) * 8)); 815 816 /* Set testclk high */ 817 SET_DPHY_TEST_CTRL1_CLK(kmb_dsi, dphy_no); 818 } 819} 820 821static inline void 822 set_test_mode_src_osc_freq_target_low_bits(struct kmb_dsi *kmb_dsi, 823 u32 dphy_no, 824 u32 freq) 825{ 826 /* Typical rise/fall time=166, refer Table 1207 databook, 827 * sr_osc_freq_target[7:0] 828 */ 829 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_SLEW_RATE_DDL_CYCLES, 830 (freq & 0x7f)); 831} 832 833static inline void 834 set_test_mode_src_osc_freq_target_hi_bits(struct kmb_dsi *kmb_dsi, 835 u32 dphy_no, 836 u32 freq) 837{ 838 u32 data; 839 840 /* Flag this as high nibble */ 841 data = ((freq >> 6) & 0x1f) | (1 << 7); 842 843 /* Typical rise/fall time=166, refer Table 1207 databook, 844 * sr_osc_freq_target[11:7] 845 */ 846 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_SLEW_RATE_DDL_CYCLES, data); 847} 848 849static void mipi_tx_get_vco_params(struct vco_params *vco) 850{ 851 int i; 852 853 for (i = 0; i < ARRAY_SIZE(vco_table); i++) { 854 if (vco->freq < vco_table[i].freq) { 855 *vco = vco_table[i]; 856 return; 857 } 858 } 859 860 WARN_ONCE(1, "Invalid vco freq = %u for PLL setup\n", vco->freq); 861} 862 863static void mipi_tx_pll_setup(struct kmb_dsi *kmb_dsi, u32 dphy_no, 864 u32 ref_clk_mhz, u32 target_freq_mhz) 865{ 866 u32 best_n = 0, best_m = 0; 867 u32 n = 0, m = 0, div = 0, delta, freq = 0, t_freq; 868 u32 best_freq_delta = 3000; 869 870 /* pll_ref_clk: - valid range: 2~64 MHz; Typically 24 MHz 871 * Fvco: - valid range: 320~1250 MHz (Gen3 D-PHY) 872 * Fout: - valid range: 40~1250 MHz (Gen3 D-PHY) 873 * n: - valid range [0 15] 874 * N: - N = n + 1 875 * -valid range: [1 16] 876 * -conditions: - (pll_ref_clk / N) >= 2 MHz 877 * -(pll_ref_clk / N) <= 8 MHz 878 * m: valid range [62 623] 879 * M: - M = m + 2 880 * -valid range [64 625] 881 * -Fvco = (M/N) * pll_ref_clk 882 */ 883 struct vco_params vco_p = { 884 .range = 0, 885 .divider = 1, 886 }; 887 888 vco_p.freq = target_freq_mhz; 889 mipi_tx_get_vco_params(&vco_p); 890 891 /* Search pll n parameter */ 892 for (n = PLL_N_MIN; n <= PLL_N_MAX; n++) { 893 /* Calculate the pll input frequency division ratio 894 * multiply by 1000 for precision - 895 * no floating point, add n for rounding 896 */ 897 div = ((ref_clk_mhz * 1000) + n) / (n + 1); 898 899 /* Found a valid n parameter */ 900 if ((div < 2000 || div > 8000)) 901 continue; 902 903 /* Search pll m parameter */ 904 for (m = PLL_M_MIN; m <= PLL_M_MAX; m++) { 905 /* Calculate the Fvco(DPHY PLL output frequency) 906 * using the current n,m params 907 */ 908 freq = div * (m + 2); 909 freq /= 1000; 910 911 /* Trim the potential pll freq to max supported */ 912 if (freq > PLL_FVCO_MAX) 913 continue; 914 915 delta = abs(freq - target_freq_mhz); 916 917 /* Select the best (closest to target pll freq) 918 * n,m parameters so far 919 */ 920 if (delta < best_freq_delta) { 921 best_n = n; 922 best_m = m; 923 best_freq_delta = delta; 924 } 925 } 926 } 927 928 /* Program vco_cntrl parameter 929 * PLL_VCO_Control[5:0] = pll_vco_cntrl_ovr, 930 * PLL_VCO_Control[6] = pll_vco_cntrl_ovr_en 931 */ 932 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_VCO_CTRL, (vco_p.range 933 | (1 << 6))); 934 935 /* Program m, n pll parameters */ 936 dev_dbg(kmb_dsi->dev, "m = %d n = %d\n", best_m, best_n); 937 938 /* PLL_Input_Divider_Ratio[3:0] = pll_n_ovr */ 939 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_INPUT_DIVIDER, 940 (best_n & 0x0f)); 941 942 /* m - low nibble PLL_Loop_Divider_Ratio[4:0] 943 * pll_m_ovr[4:0] 944 */ 945 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_FEEDBACK_DIVIDER, 946 (best_m & 0x1f)); 947 948 /* m - high nibble PLL_Loop_Divider_Ratio[4:0] 949 * pll_m_ovr[9:5] 950 */ 951 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_FEEDBACK_DIVIDER, 952 ((best_m >> 5) & 0x1f) | PLL_FEEDBACK_DIVIDER_HIGH); 953 954 /* Enable overwrite of n,m parameters :pll_n_ovr_en, pll_m_ovr_en */ 955 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_OUTPUT_CLK_SEL, 956 (PLL_N_OVR_EN | PLL_M_OVR_EN)); 957 958 /* Program Charge-Pump parameters */ 959 960 /* pll_prop_cntrl-fixed values for prop_cntrl from DPHY doc */ 961 t_freq = target_freq_mhz * vco_p.divider; 962 test_mode_send(kmb_dsi, dphy_no, 963 TEST_CODE_PLL_PROPORTIONAL_CHARGE_PUMP_CTRL, 964 ((t_freq > 1150) ? 0x0C : 0x0B)); 965 966 /* pll_int_cntrl-fixed value for int_cntrl from DPHY doc */ 967 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_INTEGRAL_CHARGE_PUMP_CTRL, 968 0x00); 969 970 /* pll_gmp_cntrl-fixed value for gmp_cntrl from DPHY doci */ 971 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_GMP_CTRL, 0x10); 972 973 /* pll_cpbias_cntrl-fixed value for cpbias_cntrl from DPHY doc */ 974 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_CHARGE_PUMP_BIAS, 0x10); 975 976 /* pll_th1 -Lock Detector Phase error threshold, 977 * document gives fixed value 978 */ 979 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_PHASE_ERR_CTRL, 0x02); 980 981 /* PLL Lock Configuration */ 982 983 /* pll_th2 - Lock Filter length, document gives fixed value */ 984 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_LOCK_FILTER, 0x60); 985 986 /* pll_th3- PLL Unlocking filter, document gives fixed value */ 987 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_UNLOCK_FILTER, 0x03); 988 989 /* pll_lock_sel-PLL Lock Detector Selection, 990 * document gives fixed value 991 */ 992 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_PLL_LOCK_DETECTOR, 0x02); 993} 994 995static void set_slewrate_gt_1500(struct kmb_dsi *kmb_dsi, u32 dphy_no) 996{ 997 u32 test_code = 0, test_data = 0; 998 /* Bypass slew rate calibration algorithm 999 * bits[1:0} srcal_en_ovr_en, srcal_en_ovr 1000 */ 1001 test_code = TEST_CODE_SLEW_RATE_OVERRIDE_CTRL; 1002 test_data = 0x02; 1003 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1004 1005 /* Disable slew rate calibration */ 1006 test_code = TEST_CODE_SLEW_RATE_DDL_LOOP_CTRL; 1007 test_data = 0x00; 1008 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1009} 1010 1011static void set_slewrate_gt_1000(struct kmb_dsi *kmb_dsi, u32 dphy_no) 1012{ 1013 u32 test_code = 0, test_data = 0; 1014 1015 /* BitRate: > 1 Gbps && <= 1.5 Gbps: - slew rate control ON 1016 * typical rise/fall times: 166 ps 1017 */ 1018 1019 /* Do not bypass slew rate calibration algorithm 1020 * bits[1:0}=srcal_en_ovr_en, srcal_en_ovr, bit[6]=sr_range 1021 */ 1022 test_code = TEST_CODE_SLEW_RATE_OVERRIDE_CTRL; 1023 test_data = (0x03 | (1 << 6)); 1024 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1025 1026 /* Enable slew rate calibration */ 1027 test_code = TEST_CODE_SLEW_RATE_DDL_LOOP_CTRL; 1028 test_data = 0x01; 1029 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1030 1031 /* Set sr_osc_freq_target[6:0] low nibble 1032 * typical rise/fall time=166, refer Table 1207 databook 1033 */ 1034 test_code = TEST_CODE_SLEW_RATE_DDL_CYCLES; 1035 test_data = (0x72f & 0x7f); 1036 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1037 1038 /* Set sr_osc_freq_target[11:7] high nibble 1039 * Typical rise/fall time=166, refer Table 1207 databook 1040 */ 1041 test_code = TEST_CODE_SLEW_RATE_DDL_CYCLES; 1042 test_data = ((0x72f >> 6) & 0x1f) | (1 << 7); 1043 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1044} 1045 1046static void set_slewrate_lt_1000(struct kmb_dsi *kmb_dsi, u32 dphy_no) 1047{ 1048 u32 test_code = 0, test_data = 0; 1049 1050 /* lane_rate_mbps <= 1000 Mbps 1051 * BitRate: <= 1 Gbps: 1052 * - slew rate control ON 1053 * - typical rise/fall times: 225 ps 1054 */ 1055 1056 /* Do not bypass slew rate calibration algorithm */ 1057 test_code = TEST_CODE_SLEW_RATE_OVERRIDE_CTRL; 1058 test_data = (0x03 | (1 << 6)); 1059 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1060 1061 /* Enable slew rate calibration */ 1062 test_code = TEST_CODE_SLEW_RATE_DDL_LOOP_CTRL; 1063 test_data = 0x01; 1064 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1065 1066 /* Typical rise/fall time=255, refer Table 1207 databook */ 1067 test_code = TEST_CODE_SLEW_RATE_DDL_CYCLES; 1068 test_data = (0x523 & 0x7f); 1069 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1070 1071 /* Set sr_osc_freq_target[11:7] high nibble */ 1072 test_code = TEST_CODE_SLEW_RATE_DDL_CYCLES; 1073 test_data = ((0x523 >> 6) & 0x1f) | (1 << 7); 1074 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1075} 1076 1077static void setup_pll(struct kmb_dsi *kmb_dsi, u32 dphy_no, 1078 struct mipi_ctrl_cfg *cfg) 1079{ 1080 u32 test_code = 0, test_data = 0; 1081 1082 /* Set PLL regulator in bypass */ 1083 test_code = TEST_CODE_PLL_ANALOG_PROG; 1084 test_data = 0x01; 1085 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1086 1087 /* PLL Parameters Setup */ 1088 mipi_tx_pll_setup(kmb_dsi, dphy_no, cfg->ref_clk_khz / 1000, 1089 cfg->lane_rate_mbps / 2); 1090 1091 /* Set clksel */ 1092 kmb_write_bits_mipi(kmb_dsi, DPHY_INIT_CTRL1, PLL_CLKSEL_0, 2, 0x01); 1093 1094 /* Set pll_shadow_control */ 1095 kmb_set_bit_mipi(kmb_dsi, DPHY_INIT_CTRL1, PLL_SHADOW_CTRL); 1096} 1097 1098static void set_lane_data_rate(struct kmb_dsi *kmb_dsi, u32 dphy_no, 1099 struct mipi_ctrl_cfg *cfg) 1100{ 1101 u32 i, test_code = 0, test_data = 0; 1102 1103 for (i = 0; i < MIPI_DPHY_DEFAULT_BIT_RATES; i++) { 1104 if (mipi_hs_freq_range[i].default_bit_rate_mbps < 1105 cfg->lane_rate_mbps) 1106 continue; 1107 1108 /* Send the test code and data */ 1109 /* bit[6:0] = hsfreqrange_ovr bit[7] = hsfreqrange_ovr_en */ 1110 test_code = TEST_CODE_HS_FREQ_RANGE_CFG; 1111 test_data = (mipi_hs_freq_range[i].hsfreqrange_code & 0x7f) | 1112 (1 << 7); 1113 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1114 break; 1115 } 1116} 1117 1118static void dphy_init_sequence(struct kmb_dsi *kmb_dsi, 1119 struct mipi_ctrl_cfg *cfg, u32 dphy_no, 1120 int active_lanes, enum dphy_mode mode) 1121{ 1122 u32 test_code = 0, test_data = 0, val; 1123 1124 /* Set D-PHY in shutdown mode */ 1125 /* Assert RSTZ signal */ 1126 CLR_DPHY_INIT_CTRL0(kmb_dsi, dphy_no, RESETZ); 1127 1128 /* Assert SHUTDOWNZ signal */ 1129 CLR_DPHY_INIT_CTRL0(kmb_dsi, dphy_no, SHUTDOWNZ); 1130 val = kmb_read_mipi(kmb_dsi, DPHY_INIT_CTRL0); 1131 1132 /* Init D-PHY_n 1133 * Pulse testclear signal to make sure the d-phy configuration 1134 * starts from a clean base 1135 */ 1136 CLR_DPHY_TEST_CTRL0(kmb_dsi, dphy_no); 1137 ndelay(15); 1138 SET_DPHY_TEST_CTRL0(kmb_dsi, dphy_no); 1139 ndelay(15); 1140 CLR_DPHY_TEST_CTRL0(kmb_dsi, dphy_no); 1141 ndelay(15); 1142 1143 /* Set mastermacro bit - Master or slave mode */ 1144 test_code = TEST_CODE_MULTIPLE_PHY_CTRL; 1145 1146 /* DPHY has its own clock lane enabled (master) */ 1147 if (mode == MIPI_DPHY_MASTER) 1148 test_data = 0x01; 1149 else 1150 test_data = 0x00; 1151 1152 /* Send the test code and data */ 1153 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1154 1155 /* Set the lane data rate */ 1156 set_lane_data_rate(kmb_dsi, dphy_no, cfg); 1157 1158 /* High-Speed Tx Slew Rate Calibration 1159 * BitRate: > 1.5 Gbps && <= 2.5 Gbps: slew rate control OFF 1160 */ 1161 if (cfg->lane_rate_mbps > 1500) 1162 set_slewrate_gt_1500(kmb_dsi, dphy_no); 1163 else if (cfg->lane_rate_mbps > 1000) 1164 set_slewrate_gt_1000(kmb_dsi, dphy_no); 1165 else 1166 set_slewrate_lt_1000(kmb_dsi, dphy_no); 1167 1168 /* Set cfgclkfreqrange */ 1169 val = (((cfg->cfg_clk_khz / 1000) - 17) * 4) & 0x3f; 1170 SET_DPHY_FREQ_CTRL0_3(kmb_dsi, dphy_no, val); 1171 1172 /* Enable config clk for the corresponding d-phy */ 1173 kmb_set_bit_mipi(kmb_dsi, DPHY_CFG_CLK_EN, dphy_no); 1174 1175 /* PLL setup */ 1176 if (mode == MIPI_DPHY_MASTER) 1177 setup_pll(kmb_dsi, dphy_no, cfg); 1178 1179 /* Send NORMAL OPERATION test code */ 1180 test_code = 0x0; 1181 test_data = 0x0; 1182 test_mode_send(kmb_dsi, dphy_no, test_code, test_data); 1183 1184 /* Configure BASEDIR for data lanes 1185 * NOTE: basedir only applies to LANE_0 of each D-PHY. 1186 * The other lanes keep their direction based on the D-PHY type, 1187 * either Rx or Tx. 1188 * bits[5:0] - BaseDir: 1 = Rx 1189 * bits[9:6] - BaseDir: 0 = Tx 1190 */ 1191 kmb_write_bits_mipi(kmb_dsi, DPHY_INIT_CTRL2, 0, 9, 0x03f); 1192 ndelay(15); 1193 1194 /* Enable CLOCK LANE 1195 * Clock lane should be enabled regardless of the direction 1196 * set for the D-PHY (Rx/Tx) 1197 */ 1198 kmb_set_bit_mipi(kmb_dsi, DPHY_INIT_CTRL2, 12 + dphy_no); 1199 1200 /* Enable DATA LANES */ 1201 kmb_write_bits_mipi(kmb_dsi, DPHY_ENABLE, dphy_no * 2, 2, 1202 ((1 << active_lanes) - 1)); 1203 1204 ndelay(15); 1205 1206 /* Take D-PHY out of shutdown mode */ 1207 /* Deassert SHUTDOWNZ signal */ 1208 SET_DPHY_INIT_CTRL0(kmb_dsi, dphy_no, SHUTDOWNZ); 1209 ndelay(15); 1210 1211 /* Deassert RSTZ signal */ 1212 SET_DPHY_INIT_CTRL0(kmb_dsi, dphy_no, RESETZ); 1213} 1214 1215static void dphy_wait_fsm(struct kmb_dsi *kmb_dsi, u32 dphy_no, 1216 enum dphy_tx_fsm fsm_state) 1217{ 1218 enum dphy_tx_fsm val = DPHY_TX_POWERDWN; 1219 int i = 0; 1220 int status = 1; 1221 1222 do { 1223 test_mode_send(kmb_dsi, dphy_no, TEST_CODE_FSM_CONTROL, 0x80); 1224 1225 val = GET_TEST_DOUT4_7(kmb_dsi, dphy_no); 1226 i++; 1227 if (i > TIMEOUT) { 1228 status = 0; 1229 break; 1230 } 1231 } while (val != fsm_state); 1232 1233 dev_dbg(kmb_dsi->dev, "%s: dphy %d val = %x", __func__, dphy_no, val); 1234 dev_dbg(kmb_dsi->dev, "* DPHY %d WAIT_FSM %s *", 1235 dphy_no, status ? "SUCCESS" : "FAILED"); 1236} 1237 1238static void wait_init_done(struct kmb_dsi *kmb_dsi, u32 dphy_no, 1239 u32 active_lanes) 1240{ 1241 u32 stopstatedata = 0; 1242 u32 data_lanes = (1 << active_lanes) - 1; 1243 int i = 0; 1244 int status = 1; 1245 1246 do { 1247 stopstatedata = GET_STOPSTATE_DATA(kmb_dsi, dphy_no) 1248 & data_lanes; 1249 1250 /* TODO-need to add a time out and return failure */ 1251 i++; 1252 1253 if (i > TIMEOUT) { 1254 status = 0; 1255 dev_dbg(kmb_dsi->dev, 1256 "! WAIT_INIT_DONE: TIMING OUT!(err_stat=%d)", 1257 kmb_read_mipi(kmb_dsi, MIPI_DPHY_ERR_STAT6_7)); 1258 break; 1259 } 1260 } while (stopstatedata != data_lanes); 1261 1262 dev_dbg(kmb_dsi->dev, "* DPHY %d INIT - %s *", 1263 dphy_no, status ? "SUCCESS" : "FAILED"); 1264} 1265 1266static void wait_pll_lock(struct kmb_dsi *kmb_dsi, u32 dphy_no) 1267{ 1268 int i = 0; 1269 int status = 1; 1270 1271 do { 1272 /* TODO-need to add a time out and return failure */ 1273 i++; 1274 if (i > TIMEOUT) { 1275 status = 0; 1276 dev_dbg(kmb_dsi->dev, "%s: timing out", __func__); 1277 break; 1278 } 1279 } while (!GET_PLL_LOCK(kmb_dsi, dphy_no)); 1280 1281 dev_dbg(kmb_dsi->dev, "* PLL Locked for DPHY %d - %s *", 1282 dphy_no, status ? "SUCCESS" : "FAILED"); 1283} 1284 1285static u32 mipi_tx_init_dphy(struct kmb_dsi *kmb_dsi, 1286 struct mipi_ctrl_cfg *cfg) 1287{ 1288 u32 dphy_no = MIPI_DPHY6; 1289 1290 /* Multiple D-PHYs needed */ 1291 if (cfg->active_lanes > MIPI_DPHY_D_LANES) { 1292 /* 1293 *Initialization for Tx aggregation mode is done according to 1294 *a. start init PHY1 1295 *b. poll for PHY1 FSM state LOCK 1296 * b1. reg addr 0x03[3:0] - state_main[3:0] == 5 (LOCK) 1297 *c. poll for PHY1 calibrations done : 1298 * c1. termination calibration lower section: addr 0x22[5] 1299 * - rescal_done 1300 * c2. slewrate calibration (if data rate < = 1500 Mbps): 1301 * addr 0xA7[3:2] - srcal_done, sr_finished 1302 *d. start init PHY0 1303 *e. poll for PHY0 stopstate 1304 *f. poll for PHY1 stopstate 1305 */ 1306 /* PHY #N+1 ('slave') */ 1307 1308 dphy_init_sequence(kmb_dsi, cfg, dphy_no + 1, 1309 (cfg->active_lanes - MIPI_DPHY_D_LANES), 1310 MIPI_DPHY_SLAVE); 1311 dphy_wait_fsm(kmb_dsi, dphy_no + 1, DPHY_TX_LOCK); 1312 1313 /* PHY #N master */ 1314 dphy_init_sequence(kmb_dsi, cfg, dphy_no, MIPI_DPHY_D_LANES, 1315 MIPI_DPHY_MASTER); 1316 1317 /* Wait for DPHY init to complete */ 1318 wait_init_done(kmb_dsi, dphy_no, MIPI_DPHY_D_LANES); 1319 wait_init_done(kmb_dsi, dphy_no + 1, 1320 cfg->active_lanes - MIPI_DPHY_D_LANES); 1321 wait_pll_lock(kmb_dsi, dphy_no); 1322 wait_pll_lock(kmb_dsi, dphy_no + 1); 1323 dphy_wait_fsm(kmb_dsi, dphy_no, DPHY_TX_IDLE); 1324 } else { /* Single DPHY */ 1325 dphy_init_sequence(kmb_dsi, cfg, dphy_no, cfg->active_lanes, 1326 MIPI_DPHY_MASTER); 1327 dphy_wait_fsm(kmb_dsi, dphy_no, DPHY_TX_IDLE); 1328 wait_init_done(kmb_dsi, dphy_no, cfg->active_lanes); 1329 wait_pll_lock(kmb_dsi, dphy_no); 1330 } 1331 1332 return 0; 1333} 1334 1335static void connect_lcd_to_mipi(struct kmb_dsi *kmb_dsi, 1336 struct drm_atomic_state *old_state) 1337{ 1338 struct regmap *msscam; 1339 1340 msscam = syscon_regmap_lookup_by_compatible("intel,keembay-msscam"); 1341 if (IS_ERR(msscam)) { 1342 dev_dbg(kmb_dsi->dev, "failed to get msscam syscon"); 1343 return; 1344 } 1345 drm_atomic_bridge_chain_enable(adv_bridge, old_state); 1346 /* DISABLE MIPI->CIF CONNECTION */ 1347 regmap_write(msscam, MSS_MIPI_CIF_CFG, 0); 1348 1349 /* ENABLE LCD->MIPI CONNECTION */ 1350 regmap_write(msscam, MSS_LCD_MIPI_CFG, 1); 1351 /* DISABLE LCD->CIF LOOPBACK */ 1352 regmap_write(msscam, MSS_LOOPBACK_CFG, 1); 1353} 1354 1355int kmb_dsi_mode_set(struct kmb_dsi *kmb_dsi, struct drm_display_mode *mode, 1356 int sys_clk_mhz, struct drm_atomic_state *old_state) 1357{ 1358 u64 data_rate; 1359 1360 kmb_dsi->sys_clk_mhz = sys_clk_mhz; 1361 mipi_tx_init_cfg.active_lanes = MIPI_TX_ACTIVE_LANES; 1362 1363 mipi_tx_frame0_sect_cfg.width_pixels = mode->crtc_hdisplay; 1364 mipi_tx_frame0_sect_cfg.height_lines = mode->crtc_vdisplay; 1365 mipitx_frame0_cfg.vsync_width = 1366 mode->crtc_vsync_end - mode->crtc_vsync_start; 1367 mipitx_frame0_cfg.v_backporch = 1368 mode->crtc_vtotal - mode->crtc_vsync_end; 1369 mipitx_frame0_cfg.v_frontporch = 1370 mode->crtc_vsync_start - mode->crtc_vdisplay; 1371 mipitx_frame0_cfg.hsync_width = 1372 mode->crtc_hsync_end - mode->crtc_hsync_start; 1373 mipitx_frame0_cfg.h_backporch = 1374 mode->crtc_htotal - mode->crtc_hsync_end; 1375 mipitx_frame0_cfg.h_frontporch = 1376 mode->crtc_hsync_start - mode->crtc_hdisplay; 1377 1378 /* Lane rate = (vtotal*htotal*fps*bpp)/4 / 1000000 1379 * to convert to Mbps 1380 */ 1381 data_rate = ((((u32)mode->crtc_vtotal * (u32)mode->crtc_htotal) * 1382 (u32)(drm_mode_vrefresh(mode)) * 1383 MIPI_TX_BPP) / mipi_tx_init_cfg.active_lanes) / 1000000; 1384 1385 dev_dbg(kmb_dsi->dev, "data_rate=%u active_lanes=%d\n", 1386 (u32)data_rate, mipi_tx_init_cfg.active_lanes); 1387 1388 /* When late rate < 800, modeset fails with 4 lanes, 1389 * so switch to 2 lanes 1390 */ 1391 if (data_rate < 800) { 1392 mipi_tx_init_cfg.active_lanes = 2; 1393 mipi_tx_init_cfg.lane_rate_mbps = data_rate * 2; 1394 } else { 1395 mipi_tx_init_cfg.lane_rate_mbps = data_rate; 1396 } 1397 1398 /* Initialize mipi controller */ 1399 mipi_tx_init_cntrl(kmb_dsi, &mipi_tx_init_cfg); 1400 1401 /* Dphy initialization */ 1402 mipi_tx_init_dphy(kmb_dsi, &mipi_tx_init_cfg); 1403 1404 connect_lcd_to_mipi(kmb_dsi, old_state); 1405 dev_info(kmb_dsi->dev, "mipi hw initialized"); 1406 1407 return 0; 1408} 1409 1410struct kmb_dsi *kmb_dsi_init(struct platform_device *pdev) 1411{ 1412 struct kmb_dsi *kmb_dsi; 1413 struct device *dev = get_device(&pdev->dev); 1414 1415 kmb_dsi = devm_kzalloc(dev, sizeof(*kmb_dsi), GFP_KERNEL); 1416 if (!kmb_dsi) { 1417 dev_err(dev, "failed to allocate kmb_dsi\n"); 1418 return ERR_PTR(-ENOMEM); 1419 } 1420 1421 kmb_dsi->host = dsi_host; 1422 kmb_dsi->host->ops = &kmb_dsi_host_ops; 1423 1424 dsi_device->host = kmb_dsi->host; 1425 kmb_dsi->device = dsi_device; 1426 1427 return kmb_dsi; 1428} 1429 1430int kmb_dsi_encoder_init(struct drm_device *dev, struct kmb_dsi *kmb_dsi) 1431{ 1432 struct drm_encoder *encoder; 1433 struct drm_connector *connector; 1434 int ret = 0; 1435 1436 encoder = &kmb_dsi->base; 1437 encoder->possible_crtcs = 1; 1438 encoder->possible_clones = 0; 1439 1440 ret = drm_simple_encoder_init(dev, encoder, DRM_MODE_ENCODER_DSI); 1441 if (ret) { 1442 dev_err(kmb_dsi->dev, "Failed to init encoder %d\n", ret); 1443 return ret; 1444 } 1445 1446 /* Link drm_bridge to encoder */ 1447 ret = drm_bridge_attach(encoder, adv_bridge, NULL, 1448 DRM_BRIDGE_ATTACH_NO_CONNECTOR); 1449 if (ret) { 1450 drm_encoder_cleanup(encoder); 1451 return ret; 1452 } 1453 drm_info(dev, "Bridge attached : SUCCESS"); 1454 connector = drm_bridge_connector_init(dev, encoder); 1455 if (IS_ERR(connector)) { 1456 DRM_ERROR("Unable to create bridge connector"); 1457 drm_encoder_cleanup(encoder); 1458 return PTR_ERR(connector); 1459 } 1460 drm_connector_attach_encoder(connector, encoder); 1461 return 0; 1462} 1463 1464int kmb_dsi_map_mmio(struct kmb_dsi *kmb_dsi) 1465{ 1466 struct resource *res; 1467 struct device *dev = kmb_dsi->dev; 1468 1469 res = platform_get_resource_byname(kmb_dsi->pdev, IORESOURCE_MEM, 1470 "mipi"); 1471 if (!res) { 1472 dev_err(dev, "failed to get resource for mipi"); 1473 return -ENOMEM; 1474 } 1475 kmb_dsi->mipi_mmio = devm_ioremap_resource(dev, res); 1476 if (IS_ERR(kmb_dsi->mipi_mmio)) { 1477 dev_err(dev, "failed to ioremap mipi registers"); 1478 return PTR_ERR(kmb_dsi->mipi_mmio); 1479 } 1480 return 0; 1481} 1482 1483static int kmb_dsi_clk_enable(struct kmb_dsi *kmb_dsi) 1484{ 1485 int ret; 1486 struct device *dev = kmb_dsi->dev; 1487 1488 ret = clk_prepare_enable(kmb_dsi->clk_mipi); 1489 if (ret) { 1490 dev_err(dev, "Failed to enable MIPI clock: %d\n", ret); 1491 return ret; 1492 } 1493 1494 ret = clk_prepare_enable(kmb_dsi->clk_mipi_ecfg); 1495 if (ret) { 1496 dev_err(dev, "Failed to enable MIPI_ECFG clock: %d\n", ret); 1497 return ret; 1498 } 1499 1500 ret = clk_prepare_enable(kmb_dsi->clk_mipi_cfg); 1501 if (ret) { 1502 dev_err(dev, "Failed to enable MIPI_CFG clock: %d\n", ret); 1503 return ret; 1504 } 1505 1506 dev_info(dev, "SUCCESS : enabled MIPI clocks\n"); 1507 return 0; 1508} 1509 1510int kmb_dsi_clk_init(struct kmb_dsi *kmb_dsi) 1511{ 1512 struct device *dev = kmb_dsi->dev; 1513 unsigned long clk; 1514 1515 kmb_dsi->clk_mipi = devm_clk_get(dev, "clk_mipi"); 1516 if (IS_ERR(kmb_dsi->clk_mipi)) { 1517 dev_err(dev, "devm_clk_get() failed clk_mipi\n"); 1518 return PTR_ERR(kmb_dsi->clk_mipi); 1519 } 1520 1521 kmb_dsi->clk_mipi_ecfg = devm_clk_get(dev, "clk_mipi_ecfg"); 1522 if (IS_ERR(kmb_dsi->clk_mipi_ecfg)) { 1523 dev_err(dev, "devm_clk_get() failed clk_mipi_ecfg\n"); 1524 return PTR_ERR(kmb_dsi->clk_mipi_ecfg); 1525 } 1526 1527 kmb_dsi->clk_mipi_cfg = devm_clk_get(dev, "clk_mipi_cfg"); 1528 if (IS_ERR(kmb_dsi->clk_mipi_cfg)) { 1529 dev_err(dev, "devm_clk_get() failed clk_mipi_cfg\n"); 1530 return PTR_ERR(kmb_dsi->clk_mipi_cfg); 1531 } 1532 /* Set MIPI clock to 24 Mhz */ 1533 clk_set_rate(kmb_dsi->clk_mipi, KMB_MIPI_DEFAULT_CLK); 1534 if (clk_get_rate(kmb_dsi->clk_mipi) != KMB_MIPI_DEFAULT_CLK) { 1535 dev_err(dev, "failed to set to clk_mipi to %d\n", 1536 KMB_MIPI_DEFAULT_CLK); 1537 return -1; 1538 } 1539 dev_dbg(dev, "clk_mipi = %ld\n", clk_get_rate(kmb_dsi->clk_mipi)); 1540 1541 clk = clk_get_rate(kmb_dsi->clk_mipi_ecfg); 1542 if (clk != KMB_MIPI_DEFAULT_CFG_CLK) { 1543 /* Set MIPI_ECFG clock to 24 Mhz */ 1544 clk_set_rate(kmb_dsi->clk_mipi_ecfg, KMB_MIPI_DEFAULT_CFG_CLK); 1545 clk = clk_get_rate(kmb_dsi->clk_mipi_ecfg); 1546 if (clk != KMB_MIPI_DEFAULT_CFG_CLK) { 1547 dev_err(dev, "failed to set to clk_mipi_ecfg to %d\n", 1548 KMB_MIPI_DEFAULT_CFG_CLK); 1549 return -1; 1550 } 1551 } 1552 1553 clk = clk_get_rate(kmb_dsi->clk_mipi_cfg); 1554 if (clk != KMB_MIPI_DEFAULT_CFG_CLK) { 1555 /* Set MIPI_CFG clock to 24 Mhz */ 1556 clk_set_rate(kmb_dsi->clk_mipi_cfg, 24000000); 1557 clk = clk_get_rate(kmb_dsi->clk_mipi_cfg); 1558 if (clk != KMB_MIPI_DEFAULT_CFG_CLK) { 1559 dev_err(dev, "failed to set clk_mipi_cfg to %d\n", 1560 KMB_MIPI_DEFAULT_CFG_CLK); 1561 return -1; 1562 } 1563 } 1564 1565 return kmb_dsi_clk_enable(kmb_dsi); 1566} 1567