1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Analog Devices ADV7511 HDMI transmitter driver
4 *
5 * Copyright 2012 Analog Devices Inc.
6 */
7
8#include <linux/clk.h>
9#include <linux/device.h>
10#include <linux/gpio/consumer.h>
11#include <linux/module.h>
12#include <linux/of.h>
13#include <linux/slab.h>
14
15#include <media/cec.h>
16
17#include <drm/drm_atomic.h>
18#include <drm/drm_atomic_helper.h>
19#include <drm/drm_edid.h>
20#include <drm/drm_print.h>
21#include <drm/drm_probe_helper.h>
22
23#include "adv7511.h"
24
25/* ADI recommended values for proper operation. */
26static const struct reg_sequence adv7511_fixed_registers[] = {
27	{ 0x98, 0x03 },
28	{ 0x9a, 0xe0 },
29	{ 0x9c, 0x30 },
30	{ 0x9d, 0x61 },
31	{ 0xa2, 0xa4 },
32	{ 0xa3, 0xa4 },
33	{ 0xe0, 0xd0 },
34	{ 0xf9, 0x00 },
35	{ 0x55, 0x02 },
36};
37
38/* -----------------------------------------------------------------------------
39 * Register access
40 */
41
42static const uint8_t adv7511_register_defaults[] = {
43	0x12, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 00 */
44	0x00, 0x00, 0x01, 0x0e, 0xbc, 0x18, 0x01, 0x13,
45	0x25, 0x37, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 10 */
46	0x46, 0x62, 0x04, 0xa8, 0x00, 0x00, 0x1c, 0x84,
47	0x1c, 0xbf, 0x04, 0xa8, 0x1e, 0x70, 0x02, 0x1e, /* 20 */
48	0x00, 0x00, 0x04, 0xa8, 0x08, 0x12, 0x1b, 0xac,
49	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 30 */
50	0x00, 0x00, 0x00, 0x80, 0x00, 0x00, 0x00, 0xb0,
51	0x00, 0x50, 0x90, 0x7e, 0x79, 0x70, 0x00, 0x00, /* 40 */
52	0x00, 0xa8, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00,
53	0x00, 0x00, 0x02, 0x0d, 0x00, 0x00, 0x00, 0x00, /* 50 */
54	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
55	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 60 */
56	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
57	0x01, 0x0a, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 70 */
58	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
59	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 80 */
60	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
61	0x00, 0x00, 0x00, 0x00, 0xc0, 0x00, 0x00, 0x00, /* 90 */
62	0x0b, 0x02, 0x00, 0x18, 0x5a, 0x60, 0x00, 0x00,
63	0x00, 0x00, 0x80, 0x80, 0x08, 0x04, 0x00, 0x00, /* a0 */
64	0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x40, 0x14,
65	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* b0 */
66	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
67	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* c0 */
68	0x00, 0x03, 0x00, 0x00, 0x02, 0x00, 0x01, 0x04,
69	0x30, 0xff, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, /* d0 */
70	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x10, 0x01,
71	0x80, 0x75, 0x00, 0x00, 0x60, 0x00, 0x00, 0x00, /* e0 */
72	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
73	0x00, 0x00, 0x00, 0x00, 0x00, 0x75, 0x11, 0x00, /* f0 */
74	0x00, 0x7c, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
75};
76
77static bool adv7511_register_volatile(struct device *dev, unsigned int reg)
78{
79	switch (reg) {
80	case ADV7511_REG_CHIP_REVISION:
81	case ADV7511_REG_SPDIF_FREQ:
82	case ADV7511_REG_CTS_AUTOMATIC1:
83	case ADV7511_REG_CTS_AUTOMATIC2:
84	case ADV7511_REG_VIC_DETECTED:
85	case ADV7511_REG_VIC_SEND:
86	case ADV7511_REG_AUX_VIC_DETECTED:
87	case ADV7511_REG_STATUS:
88	case ADV7511_REG_GC(1):
89	case ADV7511_REG_INT(0):
90	case ADV7511_REG_INT(1):
91	case ADV7511_REG_PLL_STATUS:
92	case ADV7511_REG_AN(0):
93	case ADV7511_REG_AN(1):
94	case ADV7511_REG_AN(2):
95	case ADV7511_REG_AN(3):
96	case ADV7511_REG_AN(4):
97	case ADV7511_REG_AN(5):
98	case ADV7511_REG_AN(6):
99	case ADV7511_REG_AN(7):
100	case ADV7511_REG_HDCP_STATUS:
101	case ADV7511_REG_BCAPS:
102	case ADV7511_REG_BKSV(0):
103	case ADV7511_REG_BKSV(1):
104	case ADV7511_REG_BKSV(2):
105	case ADV7511_REG_BKSV(3):
106	case ADV7511_REG_BKSV(4):
107	case ADV7511_REG_DDC_STATUS:
108	case ADV7511_REG_EDID_READ_CTRL:
109	case ADV7511_REG_BSTATUS(0):
110	case ADV7511_REG_BSTATUS(1):
111	case ADV7511_REG_CHIP_ID_HIGH:
112	case ADV7511_REG_CHIP_ID_LOW:
113		return true;
114	}
115
116	return false;
117}
118
119static const struct regmap_config adv7511_regmap_config = {
120	.reg_bits = 8,
121	.val_bits = 8,
122
123	.max_register = 0xff,
124	.cache_type = REGCACHE_MAPLE,
125	.reg_defaults_raw = adv7511_register_defaults,
126	.num_reg_defaults_raw = ARRAY_SIZE(adv7511_register_defaults),
127
128	.volatile_reg = adv7511_register_volatile,
129};
130
131/* -----------------------------------------------------------------------------
132 * Hardware configuration
133 */
134
135static void adv7511_set_colormap(struct adv7511 *adv7511, bool enable,
136				 const uint16_t *coeff,
137				 unsigned int scaling_factor)
138{
139	unsigned int i;
140
141	regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(1),
142			   ADV7511_CSC_UPDATE_MODE, ADV7511_CSC_UPDATE_MODE);
143
144	if (enable) {
145		for (i = 0; i < 12; ++i) {
146			regmap_update_bits(adv7511->regmap,
147					   ADV7511_REG_CSC_UPPER(i),
148					   0x1f, coeff[i] >> 8);
149			regmap_write(adv7511->regmap,
150				     ADV7511_REG_CSC_LOWER(i),
151				     coeff[i] & 0xff);
152		}
153	}
154
155	if (enable)
156		regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(0),
157				   0xe0, 0x80 | (scaling_factor << 5));
158	else
159		regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(0),
160				   0x80, 0x00);
161
162	regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(1),
163			   ADV7511_CSC_UPDATE_MODE, 0);
164}
165
166static int adv7511_packet_enable(struct adv7511 *adv7511, unsigned int packet)
167{
168	if (packet & 0xff)
169		regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE0,
170				   packet, 0xff);
171
172	if (packet & 0xff00) {
173		packet >>= 8;
174		regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE1,
175				   packet, 0xff);
176	}
177
178	return 0;
179}
180
181static int adv7511_packet_disable(struct adv7511 *adv7511, unsigned int packet)
182{
183	if (packet & 0xff)
184		regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE0,
185				   packet, 0x00);
186
187	if (packet & 0xff00) {
188		packet >>= 8;
189		regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE1,
190				   packet, 0x00);
191	}
192
193	return 0;
194}
195
196/* Coefficients for adv7511 color space conversion */
197static const uint16_t adv7511_csc_ycbcr_to_rgb[] = {
198	0x0734, 0x04ad, 0x0000, 0x1c1b,
199	0x1ddc, 0x04ad, 0x1f24, 0x0135,
200	0x0000, 0x04ad, 0x087c, 0x1b77,
201};
202
203static void adv7511_set_config_csc(struct adv7511 *adv7511,
204				   struct drm_connector *connector,
205				   bool rgb, bool hdmi_mode)
206{
207	struct adv7511_video_config config;
208	bool output_format_422, output_format_ycbcr;
209	unsigned int mode;
210	uint8_t infoframe[17];
211
212	config.hdmi_mode = hdmi_mode;
213
214	hdmi_avi_infoframe_init(&config.avi_infoframe);
215
216	config.avi_infoframe.scan_mode = HDMI_SCAN_MODE_UNDERSCAN;
217
218	if (rgb) {
219		config.csc_enable = false;
220		config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB;
221	} else {
222		config.csc_scaling_factor = ADV7511_CSC_SCALING_4;
223		config.csc_coefficents = adv7511_csc_ycbcr_to_rgb;
224
225		if ((connector->display_info.color_formats &
226		     DRM_COLOR_FORMAT_YCBCR422) &&
227		    config.hdmi_mode) {
228			config.csc_enable = false;
229			config.avi_infoframe.colorspace =
230				HDMI_COLORSPACE_YUV422;
231		} else {
232			config.csc_enable = true;
233			config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB;
234		}
235	}
236
237	if (config.hdmi_mode) {
238		mode = ADV7511_HDMI_CFG_MODE_HDMI;
239
240		switch (config.avi_infoframe.colorspace) {
241		case HDMI_COLORSPACE_YUV444:
242			output_format_422 = false;
243			output_format_ycbcr = true;
244			break;
245		case HDMI_COLORSPACE_YUV422:
246			output_format_422 = true;
247			output_format_ycbcr = true;
248			break;
249		default:
250			output_format_422 = false;
251			output_format_ycbcr = false;
252			break;
253		}
254	} else {
255		mode = ADV7511_HDMI_CFG_MODE_DVI;
256		output_format_422 = false;
257		output_format_ycbcr = false;
258	}
259
260	adv7511_packet_disable(adv7511, ADV7511_PACKET_ENABLE_AVI_INFOFRAME);
261
262	adv7511_set_colormap(adv7511, config.csc_enable,
263			     config.csc_coefficents,
264			     config.csc_scaling_factor);
265
266	regmap_update_bits(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG1, 0x81,
267			   (output_format_422 << 7) | output_format_ycbcr);
268
269	regmap_update_bits(adv7511->regmap, ADV7511_REG_HDCP_HDMI_CFG,
270			   ADV7511_HDMI_CFG_MODE_MASK, mode);
271
272	hdmi_avi_infoframe_pack(&config.avi_infoframe, infoframe,
273				sizeof(infoframe));
274
275	/* The AVI infoframe id is not configurable */
276	regmap_bulk_write(adv7511->regmap, ADV7511_REG_AVI_INFOFRAME_VERSION,
277			  infoframe + 1, sizeof(infoframe) - 1);
278
279	adv7511_packet_enable(adv7511, ADV7511_PACKET_ENABLE_AVI_INFOFRAME);
280}
281
282static void adv7511_set_link_config(struct adv7511 *adv7511,
283				    const struct adv7511_link_config *config)
284{
285	/*
286	 * The input style values documented in the datasheet don't match the
287	 * hardware register field values :-(
288	 */
289	static const unsigned int input_styles[4] = { 0, 2, 1, 3 };
290
291	unsigned int clock_delay;
292	unsigned int color_depth;
293	unsigned int input_id;
294
295	clock_delay = (config->clock_delay + 1200) / 400;
296	color_depth = config->input_color_depth == 8 ? 3
297		    : (config->input_color_depth == 10 ? 1 : 2);
298
299	/* TODO Support input ID 6 */
300	if (config->input_colorspace != HDMI_COLORSPACE_YUV422)
301		input_id = config->input_clock == ADV7511_INPUT_CLOCK_DDR
302			 ? 5 : 0;
303	else if (config->input_clock == ADV7511_INPUT_CLOCK_DDR)
304		input_id = config->embedded_sync ? 8 : 7;
305	else if (config->input_clock == ADV7511_INPUT_CLOCK_2X)
306		input_id = config->embedded_sync ? 4 : 3;
307	else
308		input_id = config->embedded_sync ? 2 : 1;
309
310	regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG, 0xf,
311			   input_id);
312	regmap_update_bits(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG1, 0x7e,
313			   (color_depth << 4) |
314			   (input_styles[config->input_style] << 2));
315	regmap_write(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG2,
316		     config->input_justification << 3);
317	regmap_write(adv7511->regmap, ADV7511_REG_TIMING_GEN_SEQ,
318		     config->sync_pulse << 2);
319
320	regmap_write(adv7511->regmap, 0xba, clock_delay << 5);
321
322	adv7511->embedded_sync = config->embedded_sync;
323	adv7511->hsync_polarity = config->hsync_polarity;
324	adv7511->vsync_polarity = config->vsync_polarity;
325	adv7511->rgb = config->input_colorspace == HDMI_COLORSPACE_RGB;
326}
327
328static void __adv7511_power_on(struct adv7511 *adv7511)
329{
330	adv7511->current_edid_segment = -1;
331
332	regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
333			   ADV7511_POWER_POWER_DOWN, 0);
334	if (adv7511->i2c_main->irq) {
335		/*
336		 * Documentation says the INT_ENABLE registers are reset in
337		 * POWER_DOWN mode. My 7511w preserved the bits, however.
338		 * Still, let's be safe and stick to the documentation.
339		 */
340		regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0),
341			     ADV7511_INT0_EDID_READY | ADV7511_INT0_HPD);
342		regmap_update_bits(adv7511->regmap,
343				   ADV7511_REG_INT_ENABLE(1),
344				   ADV7511_INT1_DDC_ERROR,
345				   ADV7511_INT1_DDC_ERROR);
346	}
347
348	/*
349	 * Per spec it is allowed to pulse the HPD signal to indicate that the
350	 * EDID information has changed. Some monitors do this when they wakeup
351	 * from standby or are enabled. When the HPD goes low the adv7511 is
352	 * reset and the outputs are disabled which might cause the monitor to
353	 * go to standby again. To avoid this we ignore the HPD pin for the
354	 * first few seconds after enabling the output. On the other hand
355	 * adv7535 require to enable HPD Override bit for proper HPD.
356	 */
357	if (adv7511->info->hpd_override_enable)
358		regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
359				   ADV7535_REG_POWER2_HPD_OVERRIDE,
360				   ADV7535_REG_POWER2_HPD_OVERRIDE);
361	else
362		regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
363				   ADV7511_REG_POWER2_HPD_SRC_MASK,
364				   ADV7511_REG_POWER2_HPD_SRC_NONE);
365}
366
367static void adv7511_power_on(struct adv7511 *adv7511)
368{
369	__adv7511_power_on(adv7511);
370
371	/*
372	 * Most of the registers are reset during power down or when HPD is low.
373	 */
374	regcache_sync(adv7511->regmap);
375
376	if (adv7511->info->has_dsi)
377		adv7533_dsi_power_on(adv7511);
378	adv7511->powered = true;
379}
380
381static void __adv7511_power_off(struct adv7511 *adv7511)
382{
383	/* TODO: setup additional power down modes */
384	if (adv7511->info->hpd_override_enable)
385		regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
386				   ADV7535_REG_POWER2_HPD_OVERRIDE, 0);
387
388	regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
389			   ADV7511_POWER_POWER_DOWN,
390			   ADV7511_POWER_POWER_DOWN);
391	regmap_update_bits(adv7511->regmap,
392			   ADV7511_REG_INT_ENABLE(1),
393			   ADV7511_INT1_DDC_ERROR, 0);
394	regcache_mark_dirty(adv7511->regmap);
395}
396
397static void adv7511_power_off(struct adv7511 *adv7511)
398{
399	__adv7511_power_off(adv7511);
400	if (adv7511->info->has_dsi)
401		adv7533_dsi_power_off(adv7511);
402	adv7511->powered = false;
403}
404
405/* -----------------------------------------------------------------------------
406 * Interrupt and hotplug detection
407 */
408
409static bool adv7511_hpd(struct adv7511 *adv7511)
410{
411	unsigned int irq0;
412	int ret;
413
414	ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
415	if (ret < 0)
416		return false;
417
418	if (irq0 & ADV7511_INT0_HPD) {
419		regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
420			     ADV7511_INT0_HPD);
421		return true;
422	}
423
424	return false;
425}
426
427static void adv7511_hpd_work(struct work_struct *work)
428{
429	struct adv7511 *adv7511 = container_of(work, struct adv7511, hpd_work);
430	enum drm_connector_status status;
431	unsigned int val;
432	int ret;
433
434	ret = regmap_read(adv7511->regmap, ADV7511_REG_STATUS, &val);
435	if (ret < 0)
436		status = connector_status_disconnected;
437	else if (val & ADV7511_STATUS_HPD)
438		status = connector_status_connected;
439	else
440		status = connector_status_disconnected;
441
442	/*
443	 * The bridge resets its registers on unplug. So when we get a plug
444	 * event and we're already supposed to be powered, cycle the bridge to
445	 * restore its state.
446	 */
447	if (status == connector_status_connected &&
448	    adv7511->connector.status == connector_status_disconnected &&
449	    adv7511->powered) {
450		regcache_mark_dirty(adv7511->regmap);
451		adv7511_power_on(adv7511);
452	}
453
454	if (adv7511->connector.status != status) {
455		adv7511->connector.status = status;
456
457		if (adv7511->connector.dev) {
458			if (status == connector_status_disconnected)
459				cec_phys_addr_invalidate(adv7511->cec_adap);
460			drm_kms_helper_hotplug_event(adv7511->connector.dev);
461		} else {
462			drm_bridge_hpd_notify(&adv7511->bridge, status);
463		}
464	}
465}
466
467static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
468{
469	unsigned int irq0, irq1;
470	int ret;
471
472	ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
473	if (ret < 0)
474		return ret;
475
476	ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(1), &irq1);
477	if (ret < 0)
478		return ret;
479
480	regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0);
481	regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1);
482
483	if (process_hpd && irq0 & ADV7511_INT0_HPD && adv7511->bridge.encoder)
484		schedule_work(&adv7511->hpd_work);
485
486	if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) {
487		adv7511->edid_read = true;
488
489		if (adv7511->i2c_main->irq)
490			wake_up_all(&adv7511->wq);
491	}
492
493#ifdef CONFIG_DRM_I2C_ADV7511_CEC
494	adv7511_cec_irq_process(adv7511, irq1);
495#endif
496
497	return 0;
498}
499
500static irqreturn_t adv7511_irq_handler(int irq, void *devid)
501{
502	struct adv7511 *adv7511 = devid;
503	int ret;
504
505	ret = adv7511_irq_process(adv7511, true);
506	return ret < 0 ? IRQ_NONE : IRQ_HANDLED;
507}
508
509/* -----------------------------------------------------------------------------
510 * EDID retrieval
511 */
512
513static int adv7511_wait_for_edid(struct adv7511 *adv7511, int timeout)
514{
515	int ret;
516
517	if (adv7511->i2c_main->irq) {
518		ret = wait_event_interruptible_timeout(adv7511->wq,
519				adv7511->edid_read, msecs_to_jiffies(timeout));
520	} else {
521		for (; timeout > 0; timeout -= 25) {
522			ret = adv7511_irq_process(adv7511, false);
523			if (ret < 0)
524				break;
525
526			if (adv7511->edid_read)
527				break;
528
529			msleep(25);
530		}
531	}
532
533	return adv7511->edid_read ? 0 : -EIO;
534}
535
536static int adv7511_get_edid_block(void *data, u8 *buf, unsigned int block,
537				  size_t len)
538{
539	struct adv7511 *adv7511 = data;
540	struct i2c_msg xfer[2];
541	uint8_t offset;
542	unsigned int i;
543	int ret;
544
545	if (len > 128)
546		return -EINVAL;
547
548	if (adv7511->current_edid_segment != block / 2) {
549		unsigned int status;
550
551		ret = regmap_read(adv7511->regmap, ADV7511_REG_DDC_STATUS,
552				  &status);
553		if (ret < 0)
554			return ret;
555
556		if (status != 2) {
557			adv7511->edid_read = false;
558			regmap_write(adv7511->regmap, ADV7511_REG_EDID_SEGMENT,
559				     block);
560			ret = adv7511_wait_for_edid(adv7511, 200);
561			if (ret < 0)
562				return ret;
563		}
564
565		/* Break this apart, hopefully more I2C controllers will
566		 * support 64 byte transfers than 256 byte transfers
567		 */
568
569		xfer[0].addr = adv7511->i2c_edid->addr;
570		xfer[0].flags = 0;
571		xfer[0].len = 1;
572		xfer[0].buf = &offset;
573		xfer[1].addr = adv7511->i2c_edid->addr;
574		xfer[1].flags = I2C_M_RD;
575		xfer[1].len = 64;
576		xfer[1].buf = adv7511->edid_buf;
577
578		offset = 0;
579
580		for (i = 0; i < 4; ++i) {
581			ret = i2c_transfer(adv7511->i2c_edid->adapter, xfer,
582					   ARRAY_SIZE(xfer));
583			if (ret < 0)
584				return ret;
585			else if (ret != 2)
586				return -EIO;
587
588			xfer[1].buf += 64;
589			offset += 64;
590		}
591
592		adv7511->current_edid_segment = block / 2;
593	}
594
595	if (block % 2 == 0)
596		memcpy(buf, adv7511->edid_buf, len);
597	else
598		memcpy(buf, adv7511->edid_buf + 128, len);
599
600	return 0;
601}
602
603/* -----------------------------------------------------------------------------
604 * ADV75xx helpers
605 */
606
607static const struct drm_edid *adv7511_edid_read(struct adv7511 *adv7511,
608						struct drm_connector *connector)
609{
610	const struct drm_edid *drm_edid;
611
612	/* Reading the EDID only works if the device is powered */
613	if (!adv7511->powered) {
614		unsigned int edid_i2c_addr =
615					(adv7511->i2c_edid->addr << 1);
616
617		__adv7511_power_on(adv7511);
618
619		/* Reset the EDID_I2C_ADDR register as it might be cleared */
620		regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR,
621			     edid_i2c_addr);
622	}
623
624	drm_edid = drm_edid_read_custom(connector, adv7511_get_edid_block, adv7511);
625
626	if (!adv7511->powered)
627		__adv7511_power_off(adv7511);
628
629	if (drm_edid) {
630		/*
631		 * FIXME: The CEC physical address should be set using
632		 * cec_s_phys_addr(adap,
633		 * connector->display_info.source_physical_address, false) from
634		 * a path that has read the EDID and called
635		 * drm_edid_connector_update().
636		 */
637		const struct edid *edid = drm_edid_raw(drm_edid);
638
639		adv7511_set_config_csc(adv7511, connector, adv7511->rgb,
640				       drm_detect_hdmi_monitor(edid));
641
642		cec_s_phys_addr_from_edid(adv7511->cec_adap, edid);
643	} else {
644		cec_s_phys_addr_from_edid(adv7511->cec_adap, NULL);
645	}
646
647	return drm_edid;
648}
649
650static int adv7511_get_modes(struct adv7511 *adv7511,
651			     struct drm_connector *connector)
652{
653	const struct drm_edid *drm_edid;
654	unsigned int count;
655
656	drm_edid = adv7511_edid_read(adv7511, connector);
657
658	drm_edid_connector_update(connector, drm_edid);
659	count = drm_edid_connector_add_modes(connector);
660
661	drm_edid_free(drm_edid);
662
663	return count;
664}
665
666static enum drm_connector_status
667adv7511_detect(struct adv7511 *adv7511, struct drm_connector *connector)
668{
669	enum drm_connector_status status;
670	unsigned int val;
671	bool hpd;
672	int ret;
673
674	ret = regmap_read(adv7511->regmap, ADV7511_REG_STATUS, &val);
675	if (ret < 0)
676		return connector_status_disconnected;
677
678	if (val & ADV7511_STATUS_HPD)
679		status = connector_status_connected;
680	else
681		status = connector_status_disconnected;
682
683	hpd = adv7511_hpd(adv7511);
684
685	/* The chip resets itself when the cable is disconnected, so in case
686	 * there is a pending HPD interrupt and the cable is connected there was
687	 * at least one transition from disconnected to connected and the chip
688	 * has to be reinitialized. */
689	if (status == connector_status_connected && hpd && adv7511->powered) {
690		regcache_mark_dirty(adv7511->regmap);
691		adv7511_power_on(adv7511);
692		if (connector)
693			adv7511_get_modes(adv7511, connector);
694		if (adv7511->status == connector_status_connected)
695			status = connector_status_disconnected;
696	} else {
697		/* Renable HPD sensing */
698		if (adv7511->info->hpd_override_enable)
699			regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
700					   ADV7535_REG_POWER2_HPD_OVERRIDE,
701					   ADV7535_REG_POWER2_HPD_OVERRIDE);
702		else
703			regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
704					   ADV7511_REG_POWER2_HPD_SRC_MASK,
705					   ADV7511_REG_POWER2_HPD_SRC_BOTH);
706	}
707
708	adv7511->status = status;
709	return status;
710}
711
712static enum drm_mode_status adv7511_mode_valid(struct adv7511 *adv7511,
713			      const struct drm_display_mode *mode)
714{
715	if (mode->clock > 165000)
716		return MODE_CLOCK_HIGH;
717
718	return MODE_OK;
719}
720
721static void adv7511_mode_set(struct adv7511 *adv7511,
722			     const struct drm_display_mode *mode,
723			     const struct drm_display_mode *adj_mode)
724{
725	unsigned int low_refresh_rate;
726	unsigned int hsync_polarity = 0;
727	unsigned int vsync_polarity = 0;
728
729	if (adv7511->embedded_sync) {
730		unsigned int hsync_offset, hsync_len;
731		unsigned int vsync_offset, vsync_len;
732
733		hsync_offset = adj_mode->crtc_hsync_start -
734			       adj_mode->crtc_hdisplay;
735		vsync_offset = adj_mode->crtc_vsync_start -
736			       adj_mode->crtc_vdisplay;
737		hsync_len = adj_mode->crtc_hsync_end -
738			    adj_mode->crtc_hsync_start;
739		vsync_len = adj_mode->crtc_vsync_end -
740			    adj_mode->crtc_vsync_start;
741
742		/* The hardware vsync generator has a off-by-one bug */
743		vsync_offset += 1;
744
745		regmap_write(adv7511->regmap, ADV7511_REG_HSYNC_PLACEMENT_MSB,
746			     ((hsync_offset >> 10) & 0x7) << 5);
747		regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(0),
748			     (hsync_offset >> 2) & 0xff);
749		regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(1),
750			     ((hsync_offset & 0x3) << 6) |
751			     ((hsync_len >> 4) & 0x3f));
752		regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(2),
753			     ((hsync_len & 0xf) << 4) |
754			     ((vsync_offset >> 6) & 0xf));
755		regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(3),
756			     ((vsync_offset & 0x3f) << 2) |
757			     ((vsync_len >> 8) & 0x3));
758		regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(4),
759			     vsync_len & 0xff);
760
761		hsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PHSYNC);
762		vsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PVSYNC);
763	} else {
764		enum adv7511_sync_polarity mode_hsync_polarity;
765		enum adv7511_sync_polarity mode_vsync_polarity;
766
767		/**
768		 * If the input signal is always low or always high we want to
769		 * invert or let it passthrough depending on the polarity of the
770		 * current mode.
771		 **/
772		if (adj_mode->flags & DRM_MODE_FLAG_NHSYNC)
773			mode_hsync_polarity = ADV7511_SYNC_POLARITY_LOW;
774		else
775			mode_hsync_polarity = ADV7511_SYNC_POLARITY_HIGH;
776
777		if (adj_mode->flags & DRM_MODE_FLAG_NVSYNC)
778			mode_vsync_polarity = ADV7511_SYNC_POLARITY_LOW;
779		else
780			mode_vsync_polarity = ADV7511_SYNC_POLARITY_HIGH;
781
782		if (adv7511->hsync_polarity != mode_hsync_polarity &&
783		    adv7511->hsync_polarity !=
784		    ADV7511_SYNC_POLARITY_PASSTHROUGH)
785			hsync_polarity = 1;
786
787		if (adv7511->vsync_polarity != mode_vsync_polarity &&
788		    adv7511->vsync_polarity !=
789		    ADV7511_SYNC_POLARITY_PASSTHROUGH)
790			vsync_polarity = 1;
791	}
792
793	if (drm_mode_vrefresh(mode) <= 24)
794		low_refresh_rate = ADV7511_LOW_REFRESH_RATE_24HZ;
795	else if (drm_mode_vrefresh(mode) <= 25)
796		low_refresh_rate = ADV7511_LOW_REFRESH_RATE_25HZ;
797	else if (drm_mode_vrefresh(mode) <= 30)
798		low_refresh_rate = ADV7511_LOW_REFRESH_RATE_30HZ;
799	else
800		low_refresh_rate = ADV7511_LOW_REFRESH_RATE_NONE;
801
802	if (adv7511->info->type == ADV7511)
803		regmap_update_bits(adv7511->regmap, 0xfb,
804				   0x6, low_refresh_rate << 1);
805	else
806		regmap_update_bits(adv7511->regmap, 0x4a,
807				   0xc, low_refresh_rate << 2);
808
809	regmap_update_bits(adv7511->regmap, 0x17,
810		0x60, (vsync_polarity << 6) | (hsync_polarity << 5));
811
812	drm_mode_copy(&adv7511->curr_mode, adj_mode);
813
814	/*
815	 * TODO Test first order 4:2:2 to 4:4:4 up conversion method, which is
816	 * supposed to give better results.
817	 */
818
819	adv7511->f_tmds = mode->clock;
820}
821
822/* -----------------------------------------------------------------------------
823 * DRM Connector Operations
824 */
825
826static struct adv7511 *connector_to_adv7511(struct drm_connector *connector)
827{
828	return container_of(connector, struct adv7511, connector);
829}
830
831static int adv7511_connector_get_modes(struct drm_connector *connector)
832{
833	struct adv7511 *adv = connector_to_adv7511(connector);
834
835	return adv7511_get_modes(adv, connector);
836}
837
838static enum drm_mode_status
839adv7511_connector_mode_valid(struct drm_connector *connector,
840			     struct drm_display_mode *mode)
841{
842	struct adv7511 *adv = connector_to_adv7511(connector);
843
844	return adv7511_mode_valid(adv, mode);
845}
846
847static struct drm_connector_helper_funcs adv7511_connector_helper_funcs = {
848	.get_modes = adv7511_connector_get_modes,
849	.mode_valid = adv7511_connector_mode_valid,
850};
851
852static enum drm_connector_status
853adv7511_connector_detect(struct drm_connector *connector, bool force)
854{
855	struct adv7511 *adv = connector_to_adv7511(connector);
856
857	return adv7511_detect(adv, connector);
858}
859
860static const struct drm_connector_funcs adv7511_connector_funcs = {
861	.fill_modes = drm_helper_probe_single_connector_modes,
862	.detect = adv7511_connector_detect,
863	.destroy = drm_connector_cleanup,
864	.reset = drm_atomic_helper_connector_reset,
865	.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
866	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
867};
868
869static int adv7511_connector_init(struct adv7511 *adv)
870{
871	struct drm_bridge *bridge = &adv->bridge;
872	int ret;
873
874	if (!bridge->encoder) {
875		DRM_ERROR("Parent encoder object not found");
876		return -ENODEV;
877	}
878
879	if (adv->i2c_main->irq)
880		adv->connector.polled = DRM_CONNECTOR_POLL_HPD;
881	else
882		adv->connector.polled = DRM_CONNECTOR_POLL_CONNECT |
883				DRM_CONNECTOR_POLL_DISCONNECT;
884
885	ret = drm_connector_init(bridge->dev, &adv->connector,
886				 &adv7511_connector_funcs,
887				 DRM_MODE_CONNECTOR_HDMIA);
888	if (ret < 0) {
889		DRM_ERROR("Failed to initialize connector with drm\n");
890		return ret;
891	}
892	drm_connector_helper_add(&adv->connector,
893				 &adv7511_connector_helper_funcs);
894	drm_connector_attach_encoder(&adv->connector, bridge->encoder);
895
896	return 0;
897}
898
899/* -----------------------------------------------------------------------------
900 * DRM Bridge Operations
901 */
902
903static struct adv7511 *bridge_to_adv7511(struct drm_bridge *bridge)
904{
905	return container_of(bridge, struct adv7511, bridge);
906}
907
908static void adv7511_bridge_enable(struct drm_bridge *bridge)
909{
910	struct adv7511 *adv = bridge_to_adv7511(bridge);
911
912	adv7511_power_on(adv);
913}
914
915static void adv7511_bridge_disable(struct drm_bridge *bridge)
916{
917	struct adv7511 *adv = bridge_to_adv7511(bridge);
918
919	adv7511_power_off(adv);
920}
921
922static void adv7511_bridge_mode_set(struct drm_bridge *bridge,
923				    const struct drm_display_mode *mode,
924				    const struct drm_display_mode *adj_mode)
925{
926	struct adv7511 *adv = bridge_to_adv7511(bridge);
927
928	adv7511_mode_set(adv, mode, adj_mode);
929}
930
931static enum drm_mode_status adv7511_bridge_mode_valid(struct drm_bridge *bridge,
932						      const struct drm_display_info *info,
933		const struct drm_display_mode *mode)
934{
935	struct adv7511 *adv = bridge_to_adv7511(bridge);
936
937	if (adv->info->has_dsi)
938		return adv7533_mode_valid(adv, mode);
939	else
940		return adv7511_mode_valid(adv, mode);
941}
942
943static int adv7511_bridge_attach(struct drm_bridge *bridge,
944				 enum drm_bridge_attach_flags flags)
945{
946	struct adv7511 *adv = bridge_to_adv7511(bridge);
947	int ret = 0;
948
949	if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
950		ret = adv7511_connector_init(adv);
951		if (ret < 0)
952			return ret;
953	}
954
955	if (adv->i2c_main->irq)
956		regmap_write(adv->regmap, ADV7511_REG_INT_ENABLE(0),
957			     ADV7511_INT0_HPD);
958
959	return ret;
960}
961
962static enum drm_connector_status adv7511_bridge_detect(struct drm_bridge *bridge)
963{
964	struct adv7511 *adv = bridge_to_adv7511(bridge);
965
966	return adv7511_detect(adv, NULL);
967}
968
969static const struct drm_edid *adv7511_bridge_edid_read(struct drm_bridge *bridge,
970						       struct drm_connector *connector)
971{
972	struct adv7511 *adv = bridge_to_adv7511(bridge);
973
974	return adv7511_edid_read(adv, connector);
975}
976
977static void adv7511_bridge_hpd_notify(struct drm_bridge *bridge,
978				      enum drm_connector_status status)
979{
980	struct adv7511 *adv = bridge_to_adv7511(bridge);
981
982	if (status == connector_status_disconnected)
983		cec_phys_addr_invalidate(adv->cec_adap);
984}
985
986static const struct drm_bridge_funcs adv7511_bridge_funcs = {
987	.enable = adv7511_bridge_enable,
988	.disable = adv7511_bridge_disable,
989	.mode_set = adv7511_bridge_mode_set,
990	.mode_valid = adv7511_bridge_mode_valid,
991	.attach = adv7511_bridge_attach,
992	.detect = adv7511_bridge_detect,
993	.edid_read = adv7511_bridge_edid_read,
994	.hpd_notify = adv7511_bridge_hpd_notify,
995};
996
997/* -----------------------------------------------------------------------------
998 * Probe & remove
999 */
1000
1001static const char * const adv7511_supply_names[] = {
1002	"avdd",
1003	"dvdd",
1004	"pvdd",
1005	"bgvdd",
1006	"dvdd-3v",
1007};
1008
1009static const char * const adv7533_supply_names[] = {
1010	"avdd",
1011	"dvdd",
1012	"pvdd",
1013	"a2vdd",
1014	"v3p3",
1015	"v1p2",
1016};
1017
1018static int adv7511_init_regulators(struct adv7511 *adv)
1019{
1020	const char * const *supply_names = adv->info->supply_names;
1021	unsigned int num_supplies = adv->info->num_supplies;
1022	struct device *dev = &adv->i2c_main->dev;
1023	unsigned int i;
1024	int ret;
1025
1026	adv->supplies = devm_kcalloc(dev, num_supplies,
1027				     sizeof(*adv->supplies), GFP_KERNEL);
1028	if (!adv->supplies)
1029		return -ENOMEM;
1030
1031	for (i = 0; i < num_supplies; i++)
1032		adv->supplies[i].supply = supply_names[i];
1033
1034	ret = devm_regulator_bulk_get(dev, num_supplies, adv->supplies);
1035	if (ret)
1036		return ret;
1037
1038	return regulator_bulk_enable(num_supplies, adv->supplies);
1039}
1040
1041static void adv7511_uninit_regulators(struct adv7511 *adv)
1042{
1043	regulator_bulk_disable(adv->info->num_supplies, adv->supplies);
1044}
1045
1046static bool adv7511_cec_register_volatile(struct device *dev, unsigned int reg)
1047{
1048	struct i2c_client *i2c = to_i2c_client(dev);
1049	struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
1050
1051	reg -= adv7511->info->reg_cec_offset;
1052
1053	switch (reg) {
1054	case ADV7511_REG_CEC_RX1_FRAME_HDR:
1055	case ADV7511_REG_CEC_RX1_FRAME_DATA0 ... ADV7511_REG_CEC_RX1_FRAME_DATA0 + 14:
1056	case ADV7511_REG_CEC_RX1_FRAME_LEN:
1057	case ADV7511_REG_CEC_RX2_FRAME_HDR:
1058	case ADV7511_REG_CEC_RX2_FRAME_DATA0 ... ADV7511_REG_CEC_RX2_FRAME_DATA0 + 14:
1059	case ADV7511_REG_CEC_RX2_FRAME_LEN:
1060	case ADV7511_REG_CEC_RX3_FRAME_HDR:
1061	case ADV7511_REG_CEC_RX3_FRAME_DATA0 ... ADV7511_REG_CEC_RX3_FRAME_DATA0 + 14:
1062	case ADV7511_REG_CEC_RX3_FRAME_LEN:
1063	case ADV7511_REG_CEC_RX_STATUS:
1064	case ADV7511_REG_CEC_RX_BUFFERS:
1065	case ADV7511_REG_CEC_TX_LOW_DRV_CNT:
1066		return true;
1067	}
1068
1069	return false;
1070}
1071
1072static const struct regmap_config adv7511_cec_regmap_config = {
1073	.reg_bits = 8,
1074	.val_bits = 8,
1075
1076	.max_register = 0xff,
1077	.cache_type = REGCACHE_MAPLE,
1078	.volatile_reg = adv7511_cec_register_volatile,
1079};
1080
1081static int adv7511_init_cec_regmap(struct adv7511 *adv)
1082{
1083	int ret;
1084
1085	adv->i2c_cec = i2c_new_ancillary_device(adv->i2c_main, "cec",
1086						ADV7511_CEC_I2C_ADDR_DEFAULT);
1087	if (IS_ERR(adv->i2c_cec))
1088		return PTR_ERR(adv->i2c_cec);
1089
1090	regmap_write(adv->regmap, ADV7511_REG_CEC_I2C_ADDR,
1091		     adv->i2c_cec->addr << 1);
1092
1093	i2c_set_clientdata(adv->i2c_cec, adv);
1094
1095	adv->regmap_cec = devm_regmap_init_i2c(adv->i2c_cec,
1096					&adv7511_cec_regmap_config);
1097	if (IS_ERR(adv->regmap_cec)) {
1098		ret = PTR_ERR(adv->regmap_cec);
1099		goto err;
1100	}
1101
1102	if (adv->info->reg_cec_offset == ADV7533_REG_CEC_OFFSET) {
1103		ret = adv7533_patch_cec_registers(adv);
1104		if (ret)
1105			goto err;
1106	}
1107
1108	return 0;
1109err:
1110	i2c_unregister_device(adv->i2c_cec);
1111	return ret;
1112}
1113
1114static int adv7511_parse_dt(struct device_node *np,
1115			    struct adv7511_link_config *config)
1116{
1117	const char *str;
1118	int ret;
1119
1120	of_property_read_u32(np, "adi,input-depth", &config->input_color_depth);
1121	if (config->input_color_depth != 8 && config->input_color_depth != 10 &&
1122	    config->input_color_depth != 12)
1123		return -EINVAL;
1124
1125	ret = of_property_read_string(np, "adi,input-colorspace", &str);
1126	if (ret < 0)
1127		return ret;
1128
1129	if (!strcmp(str, "rgb"))
1130		config->input_colorspace = HDMI_COLORSPACE_RGB;
1131	else if (!strcmp(str, "yuv422"))
1132		config->input_colorspace = HDMI_COLORSPACE_YUV422;
1133	else if (!strcmp(str, "yuv444"))
1134		config->input_colorspace = HDMI_COLORSPACE_YUV444;
1135	else
1136		return -EINVAL;
1137
1138	ret = of_property_read_string(np, "adi,input-clock", &str);
1139	if (ret < 0)
1140		return ret;
1141
1142	if (!strcmp(str, "1x"))
1143		config->input_clock = ADV7511_INPUT_CLOCK_1X;
1144	else if (!strcmp(str, "2x"))
1145		config->input_clock = ADV7511_INPUT_CLOCK_2X;
1146	else if (!strcmp(str, "ddr"))
1147		config->input_clock = ADV7511_INPUT_CLOCK_DDR;
1148	else
1149		return -EINVAL;
1150
1151	if (config->input_colorspace == HDMI_COLORSPACE_YUV422 ||
1152	    config->input_clock != ADV7511_INPUT_CLOCK_1X) {
1153		ret = of_property_read_u32(np, "adi,input-style",
1154					   &config->input_style);
1155		if (ret)
1156			return ret;
1157
1158		if (config->input_style < 1 || config->input_style > 3)
1159			return -EINVAL;
1160
1161		ret = of_property_read_string(np, "adi,input-justification",
1162					      &str);
1163		if (ret < 0)
1164			return ret;
1165
1166		if (!strcmp(str, "left"))
1167			config->input_justification =
1168				ADV7511_INPUT_JUSTIFICATION_LEFT;
1169		else if (!strcmp(str, "evenly"))
1170			config->input_justification =
1171				ADV7511_INPUT_JUSTIFICATION_EVENLY;
1172		else if (!strcmp(str, "right"))
1173			config->input_justification =
1174				ADV7511_INPUT_JUSTIFICATION_RIGHT;
1175		else
1176			return -EINVAL;
1177
1178	} else {
1179		config->input_style = 1;
1180		config->input_justification = ADV7511_INPUT_JUSTIFICATION_LEFT;
1181	}
1182
1183	of_property_read_u32(np, "adi,clock-delay", &config->clock_delay);
1184	if (config->clock_delay < -1200 || config->clock_delay > 1600)
1185		return -EINVAL;
1186
1187	config->embedded_sync = of_property_read_bool(np, "adi,embedded-sync");
1188
1189	/* Hardcode the sync pulse configurations for now. */
1190	config->sync_pulse = ADV7511_INPUT_SYNC_PULSE_NONE;
1191	config->vsync_polarity = ADV7511_SYNC_POLARITY_PASSTHROUGH;
1192	config->hsync_polarity = ADV7511_SYNC_POLARITY_PASSTHROUGH;
1193
1194	return 0;
1195}
1196
1197static int adv7511_probe(struct i2c_client *i2c)
1198{
1199	struct adv7511_link_config link_config;
1200	struct adv7511 *adv7511;
1201	struct device *dev = &i2c->dev;
1202	unsigned int val;
1203	int ret;
1204
1205	if (!dev->of_node)
1206		return -EINVAL;
1207
1208	adv7511 = devm_kzalloc(dev, sizeof(*adv7511), GFP_KERNEL);
1209	if (!adv7511)
1210		return -ENOMEM;
1211
1212	adv7511->i2c_main = i2c;
1213	adv7511->powered = false;
1214	adv7511->status = connector_status_disconnected;
1215	adv7511->info = i2c_get_match_data(i2c);
1216
1217	memset(&link_config, 0, sizeof(link_config));
1218
1219	if (adv7511->info->link_config)
1220		ret = adv7511_parse_dt(dev->of_node, &link_config);
1221	else
1222		ret = adv7533_parse_dt(dev->of_node, adv7511);
1223	if (ret)
1224		return ret;
1225
1226	ret = adv7511_init_regulators(adv7511);
1227	if (ret)
1228		return dev_err_probe(dev, ret, "failed to init regulators\n");
1229
1230	/*
1231	 * The power down GPIO is optional. If present, toggle it from active to
1232	 * inactive to wake up the encoder.
1233	 */
1234	adv7511->gpio_pd = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH);
1235	if (IS_ERR(adv7511->gpio_pd)) {
1236		ret = PTR_ERR(adv7511->gpio_pd);
1237		goto uninit_regulators;
1238	}
1239
1240	if (adv7511->gpio_pd) {
1241		usleep_range(5000, 6000);
1242		gpiod_set_value_cansleep(adv7511->gpio_pd, 0);
1243	}
1244
1245	adv7511->regmap = devm_regmap_init_i2c(i2c, &adv7511_regmap_config);
1246	if (IS_ERR(adv7511->regmap)) {
1247		ret = PTR_ERR(adv7511->regmap);
1248		goto uninit_regulators;
1249	}
1250
1251	ret = regmap_read(adv7511->regmap, ADV7511_REG_CHIP_REVISION, &val);
1252	if (ret)
1253		goto uninit_regulators;
1254	dev_dbg(dev, "Rev. %d\n", val);
1255
1256	if (adv7511->info->type == ADV7511)
1257		ret = regmap_register_patch(adv7511->regmap,
1258					    adv7511_fixed_registers,
1259					    ARRAY_SIZE(adv7511_fixed_registers));
1260	else
1261		ret = adv7533_patch_registers(adv7511);
1262	if (ret)
1263		goto uninit_regulators;
1264
1265	adv7511_packet_disable(adv7511, 0xffff);
1266
1267	adv7511->i2c_edid = i2c_new_ancillary_device(i2c, "edid",
1268					ADV7511_EDID_I2C_ADDR_DEFAULT);
1269	if (IS_ERR(adv7511->i2c_edid)) {
1270		ret = PTR_ERR(adv7511->i2c_edid);
1271		goto uninit_regulators;
1272	}
1273
1274	regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR,
1275		     adv7511->i2c_edid->addr << 1);
1276
1277	adv7511->i2c_packet = i2c_new_ancillary_device(i2c, "packet",
1278					ADV7511_PACKET_I2C_ADDR_DEFAULT);
1279	if (IS_ERR(adv7511->i2c_packet)) {
1280		ret = PTR_ERR(adv7511->i2c_packet);
1281		goto err_i2c_unregister_edid;
1282	}
1283
1284	regmap_write(adv7511->regmap, ADV7511_REG_PACKET_I2C_ADDR,
1285		     adv7511->i2c_packet->addr << 1);
1286
1287	ret = adv7511_init_cec_regmap(adv7511);
1288	if (ret)
1289		goto err_i2c_unregister_packet;
1290
1291	INIT_WORK(&adv7511->hpd_work, adv7511_hpd_work);
1292
1293	adv7511_power_off(adv7511);
1294
1295	i2c_set_clientdata(i2c, adv7511);
1296
1297	if (adv7511->info->link_config)
1298		adv7511_set_link_config(adv7511, &link_config);
1299
1300	ret = adv7511_cec_init(dev, adv7511);
1301	if (ret)
1302		goto err_unregister_cec;
1303
1304	adv7511->bridge.funcs = &adv7511_bridge_funcs;
1305	adv7511->bridge.ops = DRM_BRIDGE_OP_DETECT | DRM_BRIDGE_OP_EDID;
1306	if (adv7511->i2c_main->irq)
1307		adv7511->bridge.ops |= DRM_BRIDGE_OP_HPD;
1308
1309	adv7511->bridge.of_node = dev->of_node;
1310	adv7511->bridge.type = DRM_MODE_CONNECTOR_HDMIA;
1311
1312	drm_bridge_add(&adv7511->bridge);
1313
1314	adv7511_audio_init(dev, adv7511);
1315
1316	if (i2c->irq) {
1317		init_waitqueue_head(&adv7511->wq);
1318
1319		ret = devm_request_threaded_irq(dev, i2c->irq, NULL,
1320						adv7511_irq_handler,
1321						IRQF_ONESHOT, dev_name(dev),
1322						adv7511);
1323		if (ret)
1324			goto err_unregister_audio;
1325	}
1326
1327	if (adv7511->info->has_dsi) {
1328		ret = adv7533_attach_dsi(adv7511);
1329		if (ret)
1330			goto err_unregister_audio;
1331	}
1332
1333	return 0;
1334
1335err_unregister_audio:
1336	adv7511_audio_exit(adv7511);
1337	drm_bridge_remove(&adv7511->bridge);
1338err_unregister_cec:
1339	cec_unregister_adapter(adv7511->cec_adap);
1340	i2c_unregister_device(adv7511->i2c_cec);
1341	clk_disable_unprepare(adv7511->cec_clk);
1342err_i2c_unregister_packet:
1343	i2c_unregister_device(adv7511->i2c_packet);
1344err_i2c_unregister_edid:
1345	i2c_unregister_device(adv7511->i2c_edid);
1346uninit_regulators:
1347	adv7511_uninit_regulators(adv7511);
1348
1349	return ret;
1350}
1351
1352static void adv7511_remove(struct i2c_client *i2c)
1353{
1354	struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
1355
1356	adv7511_uninit_regulators(adv7511);
1357
1358	drm_bridge_remove(&adv7511->bridge);
1359
1360	adv7511_audio_exit(adv7511);
1361
1362	cec_unregister_adapter(adv7511->cec_adap);
1363	i2c_unregister_device(adv7511->i2c_cec);
1364	clk_disable_unprepare(adv7511->cec_clk);
1365
1366	i2c_unregister_device(adv7511->i2c_packet);
1367	i2c_unregister_device(adv7511->i2c_edid);
1368}
1369
1370static const struct adv7511_chip_info adv7511_chip_info = {
1371	.type = ADV7511,
1372	.supply_names = adv7511_supply_names,
1373	.num_supplies = ARRAY_SIZE(adv7511_supply_names),
1374	.link_config = true,
1375};
1376
1377static const struct adv7511_chip_info adv7533_chip_info = {
1378	.type = ADV7533,
1379	.max_mode_clock_khz = 80000,
1380	.max_lane_freq_khz = 800000,
1381	.supply_names = adv7533_supply_names,
1382	.num_supplies = ARRAY_SIZE(adv7533_supply_names),
1383	.reg_cec_offset = ADV7533_REG_CEC_OFFSET,
1384	.has_dsi = true,
1385};
1386
1387static const struct adv7511_chip_info adv7535_chip_info = {
1388	.type = ADV7535,
1389	.max_mode_clock_khz = 148500,
1390	.max_lane_freq_khz = 891000,
1391	.supply_names = adv7533_supply_names,
1392	.num_supplies = ARRAY_SIZE(adv7533_supply_names),
1393	.reg_cec_offset = ADV7533_REG_CEC_OFFSET,
1394	.has_dsi = true,
1395	.hpd_override_enable = true,
1396};
1397
1398static const struct i2c_device_id adv7511_i2c_ids[] = {
1399	{ "adv7511", (kernel_ulong_t)&adv7511_chip_info },
1400	{ "adv7511w", (kernel_ulong_t)&adv7511_chip_info },
1401	{ "adv7513", (kernel_ulong_t)&adv7511_chip_info },
1402	{ "adv7533", (kernel_ulong_t)&adv7533_chip_info },
1403	{ "adv7535", (kernel_ulong_t)&adv7535_chip_info },
1404	{ }
1405};
1406MODULE_DEVICE_TABLE(i2c, adv7511_i2c_ids);
1407
1408static const struct of_device_id adv7511_of_ids[] = {
1409	{ .compatible = "adi,adv7511", .data = &adv7511_chip_info },
1410	{ .compatible = "adi,adv7511w", .data = &adv7511_chip_info },
1411	{ .compatible = "adi,adv7513", .data = &adv7511_chip_info },
1412	{ .compatible = "adi,adv7533", .data = &adv7533_chip_info },
1413	{ .compatible = "adi,adv7535", .data = &adv7535_chip_info },
1414	{ }
1415};
1416MODULE_DEVICE_TABLE(of, adv7511_of_ids);
1417
1418static struct mipi_dsi_driver adv7533_dsi_driver = {
1419	.driver.name = "adv7533",
1420};
1421
1422static struct i2c_driver adv7511_driver = {
1423	.driver = {
1424		.name = "adv7511",
1425		.of_match_table = adv7511_of_ids,
1426	},
1427	.id_table = adv7511_i2c_ids,
1428	.probe = adv7511_probe,
1429	.remove = adv7511_remove,
1430};
1431
1432static int __init adv7511_init(void)
1433{
1434	int ret;
1435
1436	if (IS_ENABLED(CONFIG_DRM_MIPI_DSI)) {
1437		ret = mipi_dsi_driver_register(&adv7533_dsi_driver);
1438		if (ret)
1439			return ret;
1440	}
1441
1442	ret = i2c_add_driver(&adv7511_driver);
1443	if (ret) {
1444		if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
1445			mipi_dsi_driver_unregister(&adv7533_dsi_driver);
1446	}
1447
1448	return ret;
1449}
1450module_init(adv7511_init);
1451
1452static void __exit adv7511_exit(void)
1453{
1454	i2c_del_driver(&adv7511_driver);
1455
1456	if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
1457		mipi_dsi_driver_unregister(&adv7533_dsi_driver);
1458}
1459module_exit(adv7511_exit);
1460
1461MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>");
1462MODULE_DESCRIPTION("ADV7511 HDMI transmitter driver");
1463MODULE_LICENSE("GPL");
1464