1# SPDX-License-Identifier: GPL-2.0
2#
3# Bus Devices
4#
5
6menu "Bus devices"
7
8config ARM_CCI
9	bool
10
11config ARM_CCI400_COMMON
12	bool
13	select ARM_CCI
14
15config ARM_CCI400_PORT_CTRL
16	bool
17	depends on ARM && OF && CPU_V7
18	select ARM_CCI400_COMMON
19	help
20	  Low level power management driver for CCI400 cache coherent
21	  interconnect for ARM platforms.
22
23config ARM_INTEGRATOR_LM
24	bool "ARM Integrator Logic Module bus"
25	depends on HAS_IOMEM
26	depends on ARCH_INTEGRATOR || COMPILE_TEST
27	default ARCH_INTEGRATOR
28	help
29	  Say y here to enable support for the ARM Logic Module bus
30	  found on the ARM Integrator AP (Application Platform)
31
32config BRCMSTB_GISB_ARB
33	tristate "Broadcom STB GISB bus arbiter"
34	depends on ARCH_BRCMSTB || BMIPS_GENERIC
35	default ARCH_BRCMSTB || BMIPS_GENERIC
36	help
37	  Driver for the Broadcom Set Top Box System-on-a-chip internal bus
38	  arbiter. This driver provides timeout and target abort error handling
39	  and internal bus master decoding.
40
41config BT1_APB
42	bool "Baikal-T1 APB-bus driver"
43	depends on MIPS_BAIKAL_T1 || COMPILE_TEST
44	select REGMAP_MMIO
45	help
46	  Baikal-T1 AXI-APB bridge is used to access the SoC subsystem CSRs.
47	  IO requests are routed to this bus by means of the DW AMBA 3 AXI
48	  Interconnect. In case of any APB protocol collisions, slave device
49	  not responding on timeout an IRQ is raised with an erroneous address
50	  reported to the APB terminator (APB Errors Handler Block). This
51	  driver provides the interrupt handler to detect the erroneous
52	  address, prints an error message about the address fault, updates an
53	  errors counter. The counter and the APB-bus operations timeout can be
54	  accessed via corresponding sysfs nodes.
55
56config BT1_AXI
57	bool "Baikal-T1 AXI-bus driver"
58	depends on MIPS_BAIKAL_T1 || COMPILE_TEST
59	select MFD_SYSCON
60	help
61	  AXI3-bus is the main communication bus connecting all high-speed
62	  peripheral IP-cores with RAM controller and with MIPS P5600 cores on
63	  Baikal-T1 SoC. Traffic arbitration is done by means of DW AMBA 3 AXI
64	  Interconnect (so called AXI Main Interconnect) routing IO requests
65	  from one SoC block to another. This driver provides a way to detect
66	  any bus protocol errors and device not responding situations by
67	  means of an embedded on top of the interconnect errors handler
68	  block (EHB). AXI Interconnect QoS arbitration tuning is currently
69	  unsupported.
70
71config MOXTET
72	tristate "CZ.NIC Turris Mox module configuration bus"
73	depends on SPI_MASTER && OF
74	help
75	  Say yes here to add support for the module configuration bus found
76	  on CZ.NIC's Turris Mox. This is needed for the ability to discover
77	  the order in which the modules are connected and to get/set some of
78	  their settings. For example the GPIOs on Mox SFP module are
79	  configured through this bus.
80
81config HISILICON_LPC
82	bool "Support for ISA I/O space on HiSilicon Hip06/7"
83	depends on (ARM64 && ARCH_HISI) || (COMPILE_TEST && !ALPHA && !HEXAGON && !PARISC)
84	depends on HAS_IOPORT
85	select INDIRECT_PIO if ARM64
86	help
87	  Driver to enable I/O access to devices attached to the Low Pin
88	  Count bus on the HiSilicon Hip06/7 SoC.
89
90config IMX_WEIM
91	bool "Freescale EIM DRIVER"
92	depends on ARCH_MXC
93	help
94	  Driver for i.MX WEIM controller.
95	  The WEIM(Wireless External Interface Module) works like a bus.
96	  You can attach many different devices on it, such as NOR, onenand.
97
98config INTEL_IXP4XX_EB
99	bool "Intel IXP4xx expansion bus interface driver"
100	depends on HAS_IOMEM
101	depends on ARCH_IXP4XX || COMPILE_TEST
102	default ARCH_IXP4XX
103	select MFD_SYSCON
104	help
105	  Driver for the Intel IXP4xx expansion bus interface. The driver is
106	  needed to set up various chip select configuration parameters before
107	  devices on the expansion bus can be discovered.
108
109config MIPS_CDMM
110	bool "MIPS Common Device Memory Map (CDMM) Driver"
111	depends on CPU_MIPSR2 || CPU_MIPSR5
112	help
113	  Driver needed for the MIPS Common Device Memory Map bus in MIPS
114	  cores. This bus is for per-CPU tightly coupled devices such as the
115	  Fast Debug Channel (FDC).
116
117	  For this to work, either your bootloader needs to enable the CDMM
118	  region at an unused physical address on the boot CPU, or else your
119	  platform code needs to implement mips_cdmm_phys_base() (see
120	  asm/cdmm.h).
121
122config MVEBU_MBUS
123	bool
124	depends on PLAT_ORION
125	help
126	  Driver needed for the MBus configuration on Marvell EBU SoCs
127	  (Kirkwood, Dove, Orion5x, MV78XX0 and Armada 370/XP).
128
129config OMAP_INTERCONNECT
130	tristate "OMAP INTERCONNECT DRIVER"
131	depends on ARCH_OMAP2PLUS
132
133	help
134	  Driver to enable OMAP interconnect error handling driver.
135
136config OMAP_OCP2SCP
137	tristate "OMAP OCP2SCP DRIVER"
138	depends on ARCH_OMAP2PLUS
139	help
140	  Driver to enable ocp2scp module which transforms ocp interface
141	  protocol to scp protocol. In OMAP4, USB PHY is connected via
142	  OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
143	  OCP2SCP.
144
145config QCOM_EBI2
146	bool "Qualcomm External Bus Interface 2 (EBI2)"
147	depends on HAS_IOMEM
148	depends on ARCH_QCOM || COMPILE_TEST
149	default ARCH_QCOM
150	help
151	  Say y here to enable support for the Qualcomm External Bus
152	  Interface 2, which can be used to connect things like NAND Flash,
153	  SRAM, ethernet adapters, FPGAs and LCD displays.
154
155config QCOM_SSC_BLOCK_BUS
156	bool "Qualcomm SSC Block Bus Init Driver"
157	  depends on ARCH_QCOM
158	  help
159	  Say y here to enable support for initializing the bus that connects
160	  the SSC block's internal bus to the cNoC (configurantion NoC) on
161	  (some) qcom SoCs.
162	  The SSC (Snapdragon Sensor Core) block contains a gpio controller,
163	  i2c/spi/uart controllers, a hexagon core, and a clock controller
164	  which provides clocks for the above.
165
166config SUN50I_DE2_BUS
167	bool "Allwinner A64 DE2 Bus Driver"
168	  default ARM64
169	  depends on ARCH_SUNXI
170	  select SUNXI_SRAM
171	  help
172	  Say y here to enable support for Allwinner A64 DE2 bus driver. It's
173	  mostly transparent, but a SRAM region needs to be claimed in the SRAM
174	  controller to make the all blocks in the DE2 part accessible.
175
176config SUNXI_RSB
177	tristate "Allwinner sunXi Reduced Serial Bus Driver"
178	  default MACH_SUN8I || MACH_SUN9I || ARM64
179	  depends on ARCH_SUNXI
180	  select REGMAP
181	  help
182	  Say y here to enable support for Allwinner's Reduced Serial Bus
183	  (RSB) support. This controller is responsible for communicating
184	  with various RSB based devices, such as AXP223, AXP8XX PMICs,
185	  and AC100/AC200 ICs.
186
187config TEGRA_ACONNECT
188	tristate "Tegra ACONNECT Bus Driver"
189	depends on ARCH_TEGRA
190	depends on OF && PM
191	help
192	  Driver for the Tegra ACONNECT bus which is used to interface with
193	  the devices inside the Audio Processing Engine (APE) for
194	  Tegra210 and later.
195
196config TEGRA_GMI
197	tristate "Tegra Generic Memory Interface bus driver"
198	depends on ARCH_TEGRA
199	help
200	  Driver for the Tegra Generic Memory Interface bus which can be used
201	  to attach devices such as NOR, UART, FPGA and more.
202
203config  TI_PWMSS
204	bool
205	default y if (ARCH_OMAP2PLUS) && (PWM_TIECAP || PWM_TIEHRPWM || TI_EQEP)
206	help
207	  PWM Subsystem driver support for AM33xx SOC.
208
209	  PWM submodules require PWM config space access from submodule
210	  drivers and require common parent driver support.
211
212config TI_SYSC
213	bool "TI sysc interconnect target module driver"
214	depends on ARCH_OMAP2PLUS || ARCH_K3
215	default y
216	help
217	  Generic driver for Texas Instruments interconnect target module
218	  found on many TI SoCs.
219
220config TS_NBUS
221	tristate "Technologic Systems NBUS Driver"
222	depends on SOC_IMX28
223	depends on OF_GPIO && PWM
224	help
225	  Driver for the Technologic Systems NBUS which is used to interface
226	  with the peripherals in the FPGA of the TS-4600 SoM.
227
228config UNIPHIER_SYSTEM_BUS
229	tristate "UniPhier System Bus driver"
230	depends on ARCH_UNIPHIER && OF
231	default y
232	help
233	  Support for UniPhier System Bus, a simple external bus.  This is
234	  needed to use on-board devices connected to UniPhier SoCs.
235
236config VEXPRESS_CONFIG
237	tristate "Versatile Express configuration bus"
238	default y if ARCH_VEXPRESS
239	depends on ARM || ARM64
240	depends on OF
241	select REGMAP
242	help
243	  Platform configuration infrastructure for the ARM Ltd.
244	  Versatile Express.
245
246config DA8XX_MSTPRI
247	bool "TI da8xx master peripheral priority driver"
248	depends on ARCH_DAVINCI_DA8XX
249	help
250	  Driver for Texas Instruments da8xx master peripheral priority
251	  configuration. Allows to adjust the priorities of all master
252	  peripherals.
253
254source "drivers/bus/fsl-mc/Kconfig"
255source "drivers/bus/mhi/Kconfig"
256
257endmenu
258