1#include <dt-bindings/pinctrl/bcm2835.h>
2#include <dt-bindings/clock/bcm2835.h>
3#include <dt-bindings/clock/bcm2835-aux.h>
4#include <dt-bindings/gpio/gpio.h>
5#include <dt-bindings/interrupt-controller/irq.h>
6#include <dt-bindings/soc/bcm2835-pm.h>
7
8/* firmware-provided startup stubs live here, where the secondary CPUs are
9 * spinning.
10 */
11/memreserve/ 0x00000000 0x00001000;
12
13/* This include file covers the common peripherals and configuration between
14 * bcm2835 and bcm2836 implementations, leaving the CPU configuration to
15 * bcm2835.dtsi and bcm2836.dtsi.
16 */
17
18/ {
19	compatible = "brcm,bcm2835";
20	model = "BCM2835";
21	#address-cells = <1>;
22	#size-cells = <1>;
23
24	aliases {
25		serial0 = &uart0;
26		serial1 = &uart1;
27	};
28
29	chosen {
30		stdout-path = "serial0:115200n8";
31	};
32
33	rmem: reserved-memory {
34		#address-cells = <1>;
35		#size-cells = <1>;
36		ranges;
37
38		cma: linux,cma {
39			compatible = "shared-dma-pool";
40			size = <0x4000000>; /* 64MB */
41			reusable;
42			linux,cma-default;
43		};
44	};
45
46	thermal-zones {
47		cpu_thermal: cpu-thermal {
48			polling-delay-passive = <0>;
49			polling-delay = <1000>;
50
51			trips {
52				cpu-crit {
53					temperature = <90000>;
54					hysteresis = <0>;
55					type = "critical";
56				};
57			};
58
59			cooling-maps {
60			};
61		};
62	};
63
64	soc {
65		compatible = "simple-bus";
66		#address-cells = <1>;
67		#size-cells = <1>;
68
69		system_timer: timer@7e003000 {
70			compatible = "brcm,bcm2835-system-timer";
71			reg = <0x7e003000 0x1000>;
72			interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
73			/* This could be a reference to BCM2835_CLOCK_TIMER,
74			 * but we don't have the driver using the common clock
75			 * support yet.
76			 */
77			clock-frequency = <1000000>;
78		};
79
80		txp: txp@7e004000 {
81			compatible = "brcm,bcm2835-txp";
82			reg = <0x7e004000 0x20>;
83			interrupts = <1 11>;
84		};
85
86		clocks: cprman@7e101000 {
87			compatible = "brcm,bcm2835-cprman";
88			#clock-cells = <1>;
89			reg = <0x7e101000 0x2000>;
90
91			/* CPRMAN derives almost everything from the
92			 * platform's oscillator.  However, the DSI
93			 * pixel clocks come from the DSI analog PHY.
94			 */
95			clocks = <&clk_osc>,
96				<&dsi0 0>, <&dsi0 1>, <&dsi0 2>,
97				<&dsi1 0>, <&dsi1 1>, <&dsi1 2>;
98		};
99
100		mailbox: mailbox@7e00b880 {
101			compatible = "brcm,bcm2835-mbox";
102			reg = <0x7e00b880 0x40>;
103			interrupts = <0 1>;
104			#mbox-cells = <0>;
105		};
106
107		gpio: gpio@7e200000 {
108			compatible = "brcm,bcm2835-gpio";
109			reg = <0x7e200000 0xb4>;
110			/*
111			 * The GPIO IP block is designed for 3 banks of GPIOs.
112			 * Each bank has a GPIO interrupt for itself.
113			 * There is an overall "any bank" interrupt.
114			 * In order, these are GIC interrupts 17, 18, 19, 20.
115			 * Since the BCM2835 only has 2 banks, the 2nd bank
116			 * interrupt output appears to be mirrored onto the
117			 * 3rd bank's interrupt signal.
118			 * So, a bank0 interrupt shows up on 17, 20, and
119			 * a bank1 interrupt shows up on 18, 19, 20!
120			 */
121			interrupts = <2 17>, <2 18>, <2 19>, <2 20>;
122
123			gpio-controller;
124			#gpio-cells = <2>;
125
126			interrupt-controller;
127			#interrupt-cells = <2>;
128
129			gpio-ranges = <&gpio 0 0 54>;
130
131			/* Defines common pin muxing groups
132			 *
133			 * While each pin can have its mux selected
134			 * for various functions individually, some
135			 * groups only make sense to switch to a
136			 * particular function together.
137			 */
138			dpi_gpio0: dpi-gpio0 {
139				brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
140					     12 13 14 15 16 17 18 19
141					     20 21 22 23 24 25 26 27>;
142				brcm,function = <BCM2835_FSEL_ALT2>;
143			};
144			emmc_gpio22: emmc-gpio22 {
145				brcm,pins = <22 23 24 25 26 27>;
146				brcm,function = <BCM2835_FSEL_ALT3>;
147			};
148			emmc_gpio34: emmc-gpio34 {
149				brcm,pins = <34 35 36 37 38 39>;
150				brcm,function = <BCM2835_FSEL_ALT3>;
151				brcm,pull = <BCM2835_PUD_OFF
152					     BCM2835_PUD_UP
153					     BCM2835_PUD_UP
154					     BCM2835_PUD_UP
155					     BCM2835_PUD_UP
156					     BCM2835_PUD_UP>;
157			};
158			emmc_gpio48: emmc-gpio48 {
159				brcm,pins = <48 49 50 51 52 53>;
160				brcm,function = <BCM2835_FSEL_ALT3>;
161			};
162
163			gpclk0_gpio4: gpclk0-gpio4 {
164				brcm,pins = <4>;
165				brcm,function = <BCM2835_FSEL_ALT0>;
166			};
167			gpclk1_gpio5: gpclk1-gpio5 {
168				brcm,pins = <5>;
169				brcm,function = <BCM2835_FSEL_ALT0>;
170			};
171			gpclk1_gpio42: gpclk1-gpio42 {
172				brcm,pins = <42>;
173				brcm,function = <BCM2835_FSEL_ALT0>;
174			};
175			gpclk1_gpio44: gpclk1-gpio44 {
176				brcm,pins = <44>;
177				brcm,function = <BCM2835_FSEL_ALT0>;
178			};
179			gpclk2_gpio6: gpclk2-gpio6 {
180				brcm,pins = <6>;
181				brcm,function = <BCM2835_FSEL_ALT0>;
182			};
183			gpclk2_gpio43: gpclk2-gpio43 {
184				brcm,pins = <43>;
185				brcm,function = <BCM2835_FSEL_ALT0>;
186				brcm,pull = <BCM2835_PUD_OFF>;
187			};
188
189			i2c0_gpio0: i2c0-gpio0 {
190				brcm,pins = <0 1>;
191				brcm,function = <BCM2835_FSEL_ALT0>;
192			};
193			i2c0_gpio28: i2c0-gpio28 {
194				brcm,pins = <28 29>;
195				brcm,function = <BCM2835_FSEL_ALT0>;
196			};
197			i2c0_gpio44: i2c0-gpio44 {
198				brcm,pins = <44 45>;
199				brcm,function = <BCM2835_FSEL_ALT1>;
200			};
201			i2c1_gpio2: i2c1-gpio2 {
202				brcm,pins = <2 3>;
203				brcm,function = <BCM2835_FSEL_ALT0>;
204			};
205			i2c1_gpio44: i2c1-gpio44 {
206				brcm,pins = <44 45>;
207				brcm,function = <BCM2835_FSEL_ALT2>;
208			};
209
210			jtag_gpio22: jtag-gpio22 {
211				brcm,pins = <22 23 24 25 26 27>;
212				brcm,function = <BCM2835_FSEL_ALT4>;
213			};
214
215			pcm_gpio18: pcm-gpio18 {
216				brcm,pins = <18 19 20 21>;
217				brcm,function = <BCM2835_FSEL_ALT0>;
218			};
219			pcm_gpio28: pcm-gpio28 {
220				brcm,pins = <28 29 30 31>;
221				brcm,function = <BCM2835_FSEL_ALT2>;
222			};
223
224			sdhost_gpio48: sdhost-gpio48 {
225				brcm,pins = <48 49 50 51 52 53>;
226				brcm,function = <BCM2835_FSEL_ALT0>;
227			};
228
229			spi0_gpio7: spi0-gpio7 {
230				brcm,pins = <7 8 9 10 11>;
231				brcm,function = <BCM2835_FSEL_ALT0>;
232			};
233			spi0_gpio35: spi0-gpio35 {
234				brcm,pins = <35 36 37 38 39>;
235				brcm,function = <BCM2835_FSEL_ALT0>;
236			};
237			spi1_gpio16: spi1-gpio16 {
238				brcm,pins = <16 17 18 19 20 21>;
239				brcm,function = <BCM2835_FSEL_ALT4>;
240			};
241			spi2_gpio40: spi2-gpio40 {
242				brcm,pins = <40 41 42 43 44 45>;
243				brcm,function = <BCM2835_FSEL_ALT4>;
244			};
245
246			uart0_gpio14: uart0-gpio14 {
247				brcm,pins = <14 15>;
248				brcm,function = <BCM2835_FSEL_ALT0>;
249			};
250			/* Separate from the uart0_gpio14 group
251			 * because it conflicts with spi1_gpio16, and
252			 * people often run uart0 on the two pins
253			 * without flow control.
254			 */
255			uart0_ctsrts_gpio16: uart0-ctsrts-gpio16 {
256				brcm,pins = <16 17>;
257				brcm,function = <BCM2835_FSEL_ALT3>;
258			};
259			uart0_ctsrts_gpio30: uart0-ctsrts-gpio30 {
260				brcm,pins = <30 31>;
261				brcm,function = <BCM2835_FSEL_ALT3>;
262				brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>;
263			};
264			uart0_gpio32: uart0-gpio32 {
265				brcm,pins = <32 33>;
266				brcm,function = <BCM2835_FSEL_ALT3>;
267				brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>;
268			};
269			uart0_gpio36: uart0-gpio36 {
270				brcm,pins = <36 37>;
271				brcm,function = <BCM2835_FSEL_ALT2>;
272			};
273			uart0_ctsrts_gpio38: uart0-ctsrts-gpio38 {
274				brcm,pins = <38 39>;
275				brcm,function = <BCM2835_FSEL_ALT2>;
276			};
277
278			uart1_gpio14: uart1-gpio14 {
279				brcm,pins = <14 15>;
280				brcm,function = <BCM2835_FSEL_ALT5>;
281			};
282			uart1_ctsrts_gpio16: uart1-ctsrts-gpio16 {
283				brcm,pins = <16 17>;
284				brcm,function = <BCM2835_FSEL_ALT5>;
285			};
286			uart1_gpio32: uart1-gpio32 {
287				brcm,pins = <32 33>;
288				brcm,function = <BCM2835_FSEL_ALT5>;
289			};
290			uart1_ctsrts_gpio30: uart1-ctsrts-gpio30 {
291				brcm,pins = <30 31>;
292				brcm,function = <BCM2835_FSEL_ALT5>;
293			};
294			uart1_gpio40: uart1-gpio40 {
295				brcm,pins = <40 41>;
296				brcm,function = <BCM2835_FSEL_ALT5>;
297			};
298			uart1_ctsrts_gpio42: uart1-ctsrts-gpio42 {
299				brcm,pins = <42 43>;
300				brcm,function = <BCM2835_FSEL_ALT5>;
301			};
302		};
303
304		uart0: serial@7e201000 {
305			compatible = "arm,pl011", "arm,primecell";
306			reg = <0x7e201000 0x200>;
307			interrupts = <2 25>;
308			clocks = <&clocks BCM2835_CLOCK_UART>,
309				 <&clocks BCM2835_CLOCK_VPU>;
310			clock-names = "uartclk", "apb_pclk";
311			arm,primecell-periphid = <0x00241011>;
312		};
313
314		sdhost: mmc@7e202000 {
315			compatible = "brcm,bcm2835-sdhost";
316			reg = <0x7e202000 0x100>;
317			interrupts = <2 24>;
318			clocks = <&clocks BCM2835_CLOCK_VPU>;
319			status = "disabled";
320		};
321
322		i2s: i2s@7e203000 {
323			compatible = "brcm,bcm2835-i2s";
324			reg = <0x7e203000 0x24>;
325			clocks = <&clocks BCM2835_CLOCK_PCM>;
326			status = "disabled";
327		};
328
329		spi: spi@7e204000 {
330			compatible = "brcm,bcm2835-spi";
331			reg = <0x7e204000 0x200>;
332			interrupts = <2 22>;
333			clocks = <&clocks BCM2835_CLOCK_VPU>;
334			#address-cells = <1>;
335			#size-cells = <0>;
336			status = "disabled";
337		};
338
339		i2c0: i2c@7e205000 {
340			compatible = "brcm,bcm2835-i2c";
341			reg = <0x7e205000 0x200>;
342			interrupts = <2 21>;
343			clocks = <&clocks BCM2835_CLOCK_VPU>;
344			#address-cells = <1>;
345			#size-cells = <0>;
346			status = "disabled";
347		};
348
349		dpi: dpi@7e208000 {
350			compatible = "brcm,bcm2835-dpi";
351			reg = <0x7e208000 0x8c>;
352			clocks = <&clocks BCM2835_CLOCK_VPU>,
353				 <&clocks BCM2835_CLOCK_DPI>;
354			clock-names = "core", "pixel";
355			status = "disabled";
356		};
357
358		dsi0: dsi@7e209000 {
359			compatible = "brcm,bcm2835-dsi0";
360			reg = <0x7e209000 0x78>;
361			interrupts = <2 4>;
362			#address-cells = <1>;
363			#size-cells = <0>;
364			#clock-cells = <1>;
365
366			clocks = <&clocks BCM2835_PLLA_DSI0>,
367				 <&clocks BCM2835_CLOCK_DSI0E>,
368				 <&clocks BCM2835_CLOCK_DSI0P>;
369			clock-names = "phy", "escape", "pixel";
370
371			clock-output-names = "dsi0_byte",
372					     "dsi0_ddr2",
373					     "dsi0_ddr";
374
375			status = "disabled";
376		};
377
378		aux: aux@7e215000 {
379			compatible = "brcm,bcm2835-aux";
380			#clock-cells = <1>;
381			reg = <0x7e215000 0x8>;
382			clocks = <&clocks BCM2835_CLOCK_VPU>;
383		};
384
385		uart1: serial@7e215040 {
386			compatible = "brcm,bcm2835-aux-uart";
387			reg = <0x7e215040 0x40>;
388			interrupts = <1 29>;
389			clocks = <&aux BCM2835_AUX_CLOCK_UART>;
390			status = "disabled";
391		};
392
393		spi1: spi@7e215080 {
394			compatible = "brcm,bcm2835-aux-spi";
395			reg = <0x7e215080 0x40>;
396			interrupts = <1 29>;
397			clocks = <&aux BCM2835_AUX_CLOCK_SPI1>;
398			#address-cells = <1>;
399			#size-cells = <0>;
400			status = "disabled";
401		};
402
403		spi2: spi@7e2150c0 {
404			compatible = "brcm,bcm2835-aux-spi";
405			reg = <0x7e2150c0 0x40>;
406			interrupts = <1 29>;
407			clocks = <&aux BCM2835_AUX_CLOCK_SPI2>;
408			#address-cells = <1>;
409			#size-cells = <0>;
410			status = "disabled";
411		};
412
413		pwm: pwm@7e20c000 {
414			compatible = "brcm,bcm2835-pwm";
415			reg = <0x7e20c000 0x28>;
416			clocks = <&clocks BCM2835_CLOCK_PWM>;
417			assigned-clocks = <&clocks BCM2835_CLOCK_PWM>;
418			assigned-clock-rates = <10000000>;
419			#pwm-cells = <3>;
420			status = "disabled";
421		};
422
423		sdhci: mmc@7e300000 {
424			compatible = "brcm,bcm2835-sdhci";
425			reg = <0x7e300000 0x100>;
426			interrupts = <2 30>;
427			clocks = <&clocks BCM2835_CLOCK_EMMC>;
428			status = "disabled";
429		};
430
431		hvs@7e400000 {
432			compatible = "brcm,bcm2835-hvs";
433			reg = <0x7e400000 0x6000>;
434			interrupts = <2 1>;
435		};
436
437		dsi1: dsi@7e700000 {
438			compatible = "brcm,bcm2835-dsi1";
439			reg = <0x7e700000 0x8c>;
440			interrupts = <2 12>;
441			#address-cells = <1>;
442			#size-cells = <0>;
443			#clock-cells = <1>;
444
445			clocks = <&clocks BCM2835_PLLD_DSI1>,
446				 <&clocks BCM2835_CLOCK_DSI1E>,
447				 <&clocks BCM2835_CLOCK_DSI1P>;
448			clock-names = "phy", "escape", "pixel";
449
450			clock-output-names = "dsi1_byte",
451					     "dsi1_ddr2",
452					     "dsi1_ddr";
453
454			status = "disabled";
455		};
456
457		i2c1: i2c@7e804000 {
458			compatible = "brcm,bcm2835-i2c";
459			reg = <0x7e804000 0x1000>;
460			interrupts = <2 21>;
461			clocks = <&clocks BCM2835_CLOCK_VPU>;
462			#address-cells = <1>;
463			#size-cells = <0>;
464			status = "disabled";
465		};
466
467		usb: usb@7e980000 {
468			compatible = "brcm,bcm2835-usb";
469			reg = <0x7e980000 0x10000>;
470			interrupts = <1 9>;
471			#address-cells = <1>;
472			#size-cells = <0>;
473			clocks = <&clk_usb>;
474			clock-names = "otg";
475			phys = <&usbphy>;
476			phy-names = "usb2-phy";
477		};
478	};
479
480	clocks {
481		/* The oscillator is the root of the clock tree. */
482		clk_osc: clk-osc {
483			compatible = "fixed-clock";
484			#clock-cells = <0>;
485			clock-output-names = "osc";
486			clock-frequency = <19200000>;
487		};
488
489		clk_usb: clk-usb {
490			compatible = "fixed-clock";
491			#clock-cells = <0>;
492			clock-output-names = "otg";
493			clock-frequency = <480000000>;
494		};
495	};
496
497	usbphy: phy {
498		compatible = "usb-nop-xceiv";
499		#phy-cells = <0>;
500	};
501};
502