1# SPDX-License-Identifier: GPL-2.0
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/spi/spi-controller.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: SPI Controller Common Properties
8
9maintainers:
10  - Mark Brown <broonie@kernel.org>
11
12description: |
13  SPI busses can be described with a node for the SPI controller device
14  and a set of child nodes for each SPI slave on the bus. The system SPI
15  controller may be described for use in SPI master mode or in SPI slave mode,
16  but not for both at the same time.
17
18properties:
19  $nodename:
20    pattern: "^spi(@.*|-([0-9]|[1-9][0-9]+))?$"
21
22  "#address-cells":
23    enum: [0, 1]
24
25  "#size-cells":
26    const: 0
27
28  cs-gpios:
29    description: |
30      GPIOs used as chip selects.
31      If that property is used, the number of chip selects will be
32      increased automatically with max(cs-gpios, hardware chip selects).
33
34      So if, for example, the controller has 4 CS lines, and the
35      cs-gpios looks like this
36        cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>;
37
38      Then it should be configured so that num_chipselect = 4, with
39      the following mapping
40        cs0 : &gpio1 0 0
41        cs1 : native
42        cs2 : &gpio1 1 0
43        cs3 : &gpio1 2 0
44
45      The second flag of a gpio descriptor can be GPIO_ACTIVE_HIGH (0)
46      or GPIO_ACTIVE_LOW(1). Legacy device trees often use 0.
47
48      There is a special rule set for combining the second flag of an
49      cs-gpio with the optional spi-cs-high flag for SPI slaves.
50
51      Each table entry defines how the CS pin is to be physically
52      driven (not considering potential gpio inversions by pinmux):
53
54      device node     | cs-gpio       | CS pin state active | Note
55      ================+===============+=====================+=====
56      spi-cs-high     | -             | H                   |
57      -               | -             | L                   |
58      spi-cs-high     | ACTIVE_HIGH   | H                   |
59      -               | ACTIVE_HIGH   | L                   | 1
60      spi-cs-high     | ACTIVE_LOW    | H                   | 2
61      -               | ACTIVE_LOW    | L                   |
62
63      Notes:
64      1) Should print a warning about polarity inversion.
65         Here it would be wise to avoid and define the gpio as
66         ACTIVE_LOW.
67      2) Should print a warning about polarity inversion
68         because ACTIVE_LOW is overridden by spi-cs-high.
69         Should be generally avoided and be replaced by
70         spi-cs-high + ACTIVE_HIGH.
71
72  fifo-depth:
73    $ref: /schemas/types.yaml#/definitions/uint32
74    description:
75      Size of the RX and TX data FIFOs in bytes.
76
77  rx-fifo-depth:
78    $ref: /schemas/types.yaml#/definitions/uint32
79    description:
80      Size of the RX data FIFO in bytes.
81
82  tx-fifo-depth:
83    $ref: /schemas/types.yaml#/definitions/uint32
84    description:
85      Size of the TX data FIFO in bytes.
86
87  num-cs:
88    $ref: /schemas/types.yaml#/definitions/uint32
89    description:
90      Total number of chip selects.
91
92  spi-slave:
93    $ref: /schemas/types.yaml#/definitions/flag
94    description:
95      The SPI controller acts as a slave, instead of a master.
96
97  slave:
98    type: object
99
100    properties:
101      compatible:
102        description:
103          Compatible of the SPI device.
104
105    required:
106      - compatible
107
108patternProperties:
109  "^.*@[0-9a-f]+$":
110    type: object
111    $ref: spi-peripheral-props.yaml
112    additionalProperties: true
113
114    properties:
115      spi-3wire:
116        $ref: /schemas/types.yaml#/definitions/flag
117        description:
118          The device requires 3-wire mode.
119
120      spi-cpha:
121        $ref: /schemas/types.yaml#/definitions/flag
122        description:
123          The device requires shifted clock phase (CPHA) mode.
124
125      spi-cpol:
126        $ref: /schemas/types.yaml#/definitions/flag
127        description:
128          The device requires inverse clock polarity (CPOL) mode.
129
130    required:
131      - compatible
132      - reg
133
134dependencies:
135  rx-fifo-depth: [ tx-fifo-depth ]
136  tx-fifo-depth: [ rx-fifo-depth ]
137
138allOf:
139  - if:
140      not:
141        required:
142          - spi-slave
143    then:
144      properties:
145        "#address-cells":
146          const: 1
147    else:
148      properties:
149        "#address-cells":
150          const: 0
151  - not:
152      required:
153        - fifo-depth
154        - rx-fifo-depth
155  - not:
156      required:
157        - fifo-depth
158        - tx-fifo-depth
159
160additionalProperties: true
161
162examples:
163  - |
164    spi@80010000 {
165        #address-cells = <1>;
166        #size-cells = <0>;
167        compatible = "fsl,imx28-spi";
168        reg = <0x80010000 0x2000>;
169        interrupts = <96>;
170        dmas = <&dma_apbh 0>;
171        dma-names = "rx-tx";
172
173        display@0 {
174            compatible = "lg,lg4573";
175            spi-max-frequency = <1000000>;
176            reg = <0>;
177        };
178
179        sensor@1 {
180            compatible = "bosch,bme680";
181            spi-max-frequency = <100000>;
182            reg = <1>;
183        };
184
185        flash@2 {
186            compatible = "jedec,spi-nor";
187            spi-max-frequency = <50000000>;
188            reg = <2>, <3>;
189            stacked-memories = /bits/ 64 <0x10000000 0x10000000>;
190        };
191    };
192