1/*- 2 * SPDX-License-Identifier: BSD-2-Clause-FreeBSD 3 * 4 * Copyright (c) 2001 Semen Ustimenko (semenu@FreeBSD.org) 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 16 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 17 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 18 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 19 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 20 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 21 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 22 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 23 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 24 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 25 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 26 * SUCH DAMAGE. 27 * 28 * $FreeBSD: releng/12.0/sys/dev/mii/acphyreg.h 326255 2017-11-27 14:52:40Z pfg $ 29 */ 30 31#ifndef _DEV_MII_ACPHYREG_H_ 32#define _DEV_MII_ACPHYREG_H_ 33 34/* 35 * Register definitions for the Altima Communications AC101 36 */ 37 38#define MII_ACPHY_POL 0x10 /* Polarity int level */ 39 40/* High byte is interrupt mask register */ 41#define MII_ACPHY_INT 0x11 /* Interrupt control/status */ 42#define AC_INT_ACOMP 0x0001 /* Autoneg complete */ 43#define AC_INT_REM_FLT 0x0002 /* Remote fault */ 44#define AC_INT_LINK_DOWN 0x0004 /* Link not OK */ 45#define AC_INT_LP_ACK 0x0008 /* FLP ack recved */ 46#define AC_INT_PD_FLT 0x0010 /* Parallel detect fault */ 47#define AC_INT_PAGE_RECV 0x0020 /* New page recved */ 48#define AC_INT_RX_ER 0x0040 /* RX_ER transitions high */ 49#define AC_INT_JAB 0x0080 /* Jabber detected */ 50 51#define MII_ACPHY_DIAG 0x12 /* Diagnostic */ 52#define AC_DIAG_RX_LOCK 0x0100 53#define AC_DIAG_RX_PASS 0x0200 54#define AC_DIAG_SPEED 0x0400 /* Aneg speed result */ 55#define AC_DIAG_DUPLEX 0x0800 /* Aneg duplex result */ 56 57#define MII_ACPHY_PWRLOOP 0x13 /* Power/Loopback */ 58#define MII_ACPHY_CBLMEAS 0x14 /* Cable meas. */ 59 60#define MII_ACPHY_MCTL 0x15 /* Mode control */ 61#define AC_MCTL_FX_SEL 0x0001 /* FX mode */ 62#define AC_MCTL_BYP_PCS 0x0002 /* Bypass PCS */ 63#define AC_MCTL_SCRMBL 0x0004 /* Data scrambling */ 64#define AC_MCTL_REM_LOOP 0x0008 /* Remote loopback */ 65#define AC_MCTL_DIS_WDT 0x0010 /* Disable watchdog timer */ 66#define AC_MCTL_DIS_REC 0x0020 /* Disable recv error counter */ 67#define AC_MCTL_REC_FULL 0x0040 /* Recv error counter full */ 68#define AC_MCTL_FRC_FEF 0x0080 /* Force Far End Fault Insert. */ 69#define AC_MCTL_DIS_FEF 0x0100 /* Disable FEF Insertion */ 70#define AC_MCTL_LED_SEL 0x0200 /* Compat LED config */ 71#define AC_MCTL_ALED_SEL 0x0400 /* ActLED RX&TX - RX only */ 72#define AC_MCTL_10BT_SEL 0x0800 /* Enable 7-wire interface */ 73#define AC_MCTL_DIS_JAB 0x1000 /* Disable jabber */ 74#define AC_MCTL_FRC_LINK 0x2000 /* Force TX link up */ 75#define AC_MCTL_DIS_NLP 0x4000 /* Disable NLP check */ 76 77#define MII_ACPHY_REC 0x18 /* Recv error counter */ 78 79#endif /* _DEV_MII_ACPHYREG_H_ */ 80