1/*- 2 * SPDX-License-Identifier: BSD-3-Clause 3 * 4 * Copyright (c) 2000-2010, LSI Logic Corporation and its contributors. 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions are 9 * met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 13 * substantially similar to the "NO WARRANTY" disclaimer below 14 * ("Disclaimer") and any redistribution must be conditioned upon including 15 * a substantially similar Disclaimer requirement for further binary 16 * redistribution. 17 * 3. Neither the name of the LSI Logic Corporation nor the names of its 18 * contributors may be used to endorse or promote products derived from 19 * this software without specific prior written permission. 20 * 21 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 22 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 23 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 24 * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 25 * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 26 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 27 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 28 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 29 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 30 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF THE COPYRIGHT 31 * OWNER OR CONTRIBUTOR IS ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 32 */ 33 34/*************************************************************************** 35 * * 36 * Description * 37 * ------------ * 38 * This include file contains SAS firmware interface IOC Log Info codes * 39 * * 40 *-------------------------------------------------------------------------* 41 */ 42 43#ifndef IOPI_IOCLOGINFO_H_INCLUDED 44#define IOPI_IOCLOGINFO_H_INCLUDED 45 46#define SAS_LOGINFO_NEXUS_LOSS 0x31170000 47#define SAS_LOGINFO_MASK 0xFFFF0000 48 49/****************************************************************************/ 50/* IOC LOGINFO defines, 0x00000000 - 0x0FFFFFFF */ 51/* Format: */ 52/* Bits 31-28: MPI_IOCLOGINFO_TYPE_SAS (3) */ 53/* Bits 27-24: IOC_LOGINFO_ORIGINATOR: 0=IOP, 1=PL, 2=IR */ 54/* Bits 23-16: LOGINFO_CODE */ 55/* Bits 15-0: LOGINFO_CODE Specific */ 56/****************************************************************************/ 57 58/****************************************************************************/ 59/* IOC_LOGINFO_ORIGINATOR defines */ 60/****************************************************************************/ 61#define IOC_LOGINFO_ORIGINATOR_IOP (0x00000000) 62#define IOC_LOGINFO_ORIGINATOR_PL (0x01000000) 63#define IOC_LOGINFO_ORIGINATOR_IR (0x02000000) 64 65#define IOC_LOGINFO_ORIGINATOR_MASK (0x0F000000) 66 67/****************************************************************************/ 68/* LOGINFO_CODE defines */ 69/****************************************************************************/ 70#define IOC_LOGINFO_CODE_MASK (0x00FF0000) 71#define IOC_LOGINFO_CODE_SHIFT (16) 72 73/****************************************************************************/ 74/* IOP LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IOP */ 75/****************************************************************************/ 76#define IOP_LOGINFO_CODE_INVALID_SAS_ADDRESS (0x00010000) 77#define IOP_LOGINFO_CODE_UNUSED2 (0x00020000) 78#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x00030000) 79#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_RT (0x00030100) /* Route Table Entry not found */ 80#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PN (0x00030200) /* Invalid Page Number */ 81#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x00030300) /* Invalid FORM */ 82#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x00030400) /* Invalid Page Type */ 83#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DNM (0x00030500) /* Device Not Mapped */ 84#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PERSIST (0x00030600) /* Persistent Page not found */ 85#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DEFAULT (0x00030700) /* Default Page not found */ 86 87#define IOP_LOGINFO_CODE_FWUPLOAD_NO_FLASH_AVAILABLE (0x0003E000) /* Tried to upload from flash, but there is none */ 88#define IOP_LOGINFO_CODE_FWUPLOAD_UNKNOWN_IMAGE_TYPE (0x0003E001) /* ImageType field contents were invalid */ 89#define IOP_LOGINFO_CODE_FWUPLOAD_WRONG_IMAGE_SIZE (0x0003E002) /* ImageSize field in TCSGE was bad/offset in MfgPg 4 was wrong */ 90#define IOP_LOGINFO_CODE_FWUPLOAD_ENTIRE_FLASH_UPLOAD_FAILED (0x0003E003) /* Error occurred while attempting to upload the entire flash */ 91#define IOP_LOGINFO_CODE_FWUPLOAD_REGION_UPLOAD_FAILED (0x0003E004) /* Error occurred while attempting to upload single flash region */ 92#define IOP_LOGINFO_CODE_FWUPLOAD_DMA_FAILURE (0x0003E005) /* Problem occurred while DMAing FW to host memory */ 93 94#define IOP_LOGINFO_CODE_DIAG_MSG_ERROR (0x00040000) /* Error handling diag msg - or'd with diag status */ 95 96#define IOP_LOGINFO_CODE_TASK_TERMINATED (0x00050000) 97 98#define IOP_LOGINFO_CODE_ENCL_MGMT_READ_ACTION_ERR0R (0x00060001) /* Read Action not supported for SEP msg */ 99#define IOP_LOGINFO_CODE_ENCL_MGMT_INVALID_BUS_ID_ERR0R (0x00060002) /* Invalid Bus/ID in SEP msg */ 100 101#define IOP_LOGINFO_CODE_TARGET_ASSIST_TERMINATED (0x00070001) 102#define IOP_LOGINFO_CODE_TARGET_STATUS_SEND_TERMINATED (0x00070002) 103#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_ALL_IO (0x00070003) 104#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO (0x00070004) 105#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO_REQ (0x00070005) 106 107#define IOP_LOGINFO_CODE_LOG_TIMESTAMP_EVENT (0x00080000) 108 109/****************************************************************************/ 110/* PL LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = PL */ 111/****************************************************************************/ 112#define PL_LOGINFO_CODE_OPEN_FAILURE (0x00010000) /* see SUB_CODE_OPEN_FAIL_ below */ 113 114#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_NO_DEST_TIME_OUT (0x00000001) 115#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PATHWAY_BLOCKED (0x00000002) 116#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_CONTINUE0 (0x00000003) 117#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_CONTINUE1 (0x00000004) 118#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_INITIALIZE0 (0x00000005) 119#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_INITIALIZE1 (0x00000006) 120#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_STOP0 (0x00000007) 121#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_STOP1 (0x00000008) 122#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RETRY (0x00000009) 123#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_BREAK (0x0000000A) 124#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0B (0x0000000B) 125#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_OPEN_TIMEOUT_EXP (0x0000000C) 126#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0D (0x0000000D) 127#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_DVTBLE_ACCSS_FAIL (0x0000000E) 128#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_BAD_DEST (0x00000011) 129#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RATE_NOT_SUPP (0x00000012) 130#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PROT_NOT_SUPP (0x00000013) 131#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON0 (0x00000014) 132#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON1 (0x00000015) 133#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON2 (0x00000016) 134#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON3 (0x00000017) 135#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_STP_RESOURCES_BSY (0x00000018) 136#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_WRONG_DESTINATION (0x00000019) 137 138#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PATH_BLOCKED (0x0000001B) /* Retry Timeout */ 139#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_AWT_MAXED (0x0000001C) /* Retry Timeout */ 140 141#define PL_LOGINFO_CODE_INVALID_SGL (0x00020000) 142#define PL_LOGINFO_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00030000) 143#define PL_LOGINFO_CODE_FRAME_XFER_ERROR (0x00040000) 144#define PL_LOGINFO_CODE_TX_FM_CONNECTED_LOW (0x00050000) 145#define PL_LOGINFO_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00060000) 146#define PL_LOGINFO_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00070000) 147#define PL_LOGINFO_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00080000) 148#define PL_LOGINFO_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00090000) 149#define PL_LOGINFO_CODE_RX_FM_INVALID_MESSAGE (0x000A0000) 150#define PL_LOGINFO_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x000B0000) 151#define PL_LOGINFO_CODE_RX_FM_CURRENT_FRAME_ERROR (0x000C0000) 152#define PL_LOGINFO_CODE_SATA_LINK_DOWN (0x000D0000) 153#define PL_LOGINFO_CODE_DISCOVERY_SATA_INIT_W_IOS (0x000E0000) 154#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x000F0000) 155#define PL_LOGINFO_CODE_CONFIG_PL_NOT_INITIALIZED (0x000F0001) /* PL not yet initialized, can't do config page req. */ 156#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x000F0100) /* Invalid Page Type */ 157#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NUM_PHYS (0x000F0200) /* Invalid Number of Phys */ 158#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NOT_IMP (0x000F0300) /* Case Not Handled */ 159#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_DEV (0x000F0400) /* No Device Found */ 160#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x000F0500) /* Invalid FORM */ 161#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PHY (0x000F0600) /* Invalid Phy */ 162#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_OWNER (0x000F0700) /* No Owner Found */ 163#define PL_LOGINFO_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00100000) 164#define PL_LOGINFO_CODE_RESET (0x00110000) /* See Sub-Codes below (PL_LOGINFO_SUB_CODE) */ 165#define PL_LOGINFO_CODE_ABORT (0x00120000) /* See Sub-Codes below (PL_LOGINFO_SUB_CODE)*/ 166#define PL_LOGINFO_CODE_IO_NOT_YET_EXECUTED (0x00130000) 167#define PL_LOGINFO_CODE_IO_EXECUTED (0x00140000) 168#define PL_LOGINFO_CODE_PERS_RESV_OUT_NOT_AFFIL_OWNER (0x00150000) 169#define PL_LOGINFO_CODE_OPEN_TXDMA_ABORT (0x00160000) 170#define PL_LOGINFO_CODE_IO_DEVICE_MISSING_DELAY_RETRY (0x00170000) 171#define PL_LOGINFO_CODE_IO_CANCELLED_DUE_TO_R_ERR (0x00180000) 172#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE (0x00000100) 173#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_NO_DEST_TIMEOUT (0x00000101) 174#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_SATA_NEG_RATE_2HI (0x00000102) 175#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_RATE_NOT_SUPPORTED (0x00000103) 176#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_BREAK (0x00000104) 177#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ZONE_VIOLATION (0x00000114) 178#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON0 (0x00000114) /* Open Reject (Zone Violation) - available on SAS-2 devices */ 179#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON1 (0x00000115) 180#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON2 (0x00000116) 181#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON3 (0x00000117) 182#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ORR_TIMEOUT (0x0000011A) /* Open Reject (Retry) Timeout */ 183#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_PATH_BLOCKED (0x0000011B) 184#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_AWT_MAXED (0x0000011C) /* Arbitration Wait Timer Maxed */ 185 186#define PL_LOGINFO_SUB_CODE_TARGET_BUS_RESET (0x00000120) 187#define PL_LOGINFO_SUB_CODE_TRANSPORT_LAYER (0x00000130) /* Leave lower nibble (1-f) reserved. */ 188#define PL_LOGINFO_SUB_CODE_PORT_LAYER (0x00000140) /* Leave lower nibble (1-f) reserved. */ 189 190#define PL_LOGINFO_SUB_CODE_INVALID_SGL (0x00000200) 191#define PL_LOGINFO_SUB_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00000300) 192#define PL_LOGINFO_SUB_CODE_FRAME_XFER_ERROR (0x00000400) /* Bits 0-3 encode Transport Status Register (offset 0x08) */ 193 /* Bit 0 is Status Bit 0: FrameXferErr */ 194 /* Bit 1 & 2 are Status Bits 16 and 17: FrameXmitErrStatus */ 195 /* Bit 3 is Status Bit 18 WriteDataLenghtGTDataLengthErr */ 196 197#define PL_LOGINFO_SUB_CODE_TX_FM_CONNECTED_LOW (0x00000500) 198#define PL_LOGINFO_SUB_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00000600) 199#define PL_LOGINFO_SUB_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00000700) 200#define PL_LOGINFO_SUB_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00000800) 201#define PL_LOGINFO_SUB_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00000900) 202#define PL_LOGINFO_SUB_CODE_RX_FM_INVALID_MESSAGE (0x00000A00) 203#define PL_LOGINFO_SUB_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x00000B00) 204#define PL_LOGINFO_SUB_CODE_RX_FM_CURRENT_FRAME_ERROR (0x00000C00) 205#define PL_LOGINFO_SUB_CODE_SATA_LINK_DOWN (0x00000D00) 206#define PL_LOGINFO_SUB_CODE_DISCOVERY_SATA_INIT_W_IOS (0x00000E00) 207#define PL_LOGINFO_SUB_CODE_DISCOVERY_REMOTE_SEP_RESET (0x00000E01) 208#define PL_LOGINFO_SUB_CODE_SECOND_OPEN (0x00000F00) 209#define PL_LOGINFO_SUB_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00001000) 210#define PL_LOGINFO_SUB_CODE_BREAK_ON_SATA_CONNECTION (0x00002000) /* not currently used in mainline */ 211#define PL_LOGINFO_SUB_CODE_BREAK_ON_STUCK_LINK (0x00003000) 212#define PL_LOGINFO_SUB_CODE_BREAK_ON_STUCK_LINK_AIP (0x00004000) 213#define PL_LOGINFO_SUB_CODE_BREAK_ON_INCOMPLETE_BREAK_RCVD (0x00005000) 214 215#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_FAILURE (0x00200000) /* Can't get SMP Frame */ 216#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_READ_ERROR (0x00200010) /* Error occurred on SMP Read */ 217#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_WRITE_ERROR (0x00200020) /* Error occurred on SMP Write */ 218#define PL_LOGINFO_CODE_ENCL_MGMT_NOT_SUPPORTED_ON_ENCL (0x00200040) /* Encl Mgmt services not available for this WWID */ 219#define PL_LOGINFO_CODE_ENCL_MGMT_ADDR_MODE_NOT_SUPPORTED (0x00200050) /* Address Mode not suppored */ 220#define PL_LOGINFO_CODE_ENCL_MGMT_BAD_SLOT_NUM (0x00200060) /* Invalid Slot Number in SEP Msg */ 221#define PL_LOGINFO_CODE_ENCL_MGMT_SGPIO_NOT_PRESENT (0x00200070) /* SGPIO not present/enabled */ 222#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_NOT_CONFIGURED (0x00200080) /* GPIO not configured */ 223#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_FRAME_ERROR (0x00200090) /* GPIO can't allocate a frame */ 224#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_CONFIG_PAGE_ERROR (0x002000A0) /* GPIO failed config page request */ 225#define PL_LOGINFO_CODE_ENCL_MGMT_SES_FRAME_ALLOC_ERROR (0x002000B0) /* Can't get frame for SES command */ 226#define PL_LOGINFO_CODE_ENCL_MGMT_SES_IO_ERROR (0x002000C0) /* I/O execution error */ 227#define PL_LOGINFO_CODE_ENCL_MGMT_SES_RETRIES_EXHAUSTED (0x002000D0) /* SEP I/O retries exhausted */ 228#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_ALLOC_ERROR (0x002000E0) /* Can't get frame for SMP command */ 229 230#define PL_LOGINFO_DA_SEP_NOT_PRESENT (0x00200100) /* SEP not present when msg received */ 231#define PL_LOGINFO_DA_SEP_SINGLE_THREAD_ERROR (0x00200101) /* Can only accept 1 msg at a time */ 232#define PL_LOGINFO_DA_SEP_ISTWI_INTR_IN_IDLE_STATE (0x00200102) /* ISTWI interrupt recvd. while IDLE */ 233#define PL_LOGINFO_DA_SEP_RECEIVED_NACK_FROM_SLAVE (0x00200103) /* SEP NACK'd, it is busy */ 234#define PL_LOGINFO_DA_SEP_DID_NOT_RECEIVE_ACK (0x00200104) /* SEP didn't rcv. ACK (Last Rcvd Bit = 1) */ 235#define PL_LOGINFO_DA_SEP_BAD_STATUS_HDR_CHKSUM (0x00200105) /* SEP stopped or sent bad chksum in Hdr */ 236#define PL_LOGINFO_DA_SEP_STOP_ON_DATA (0x00200106) /* SEP stopped while transferring data */ 237#define PL_LOGINFO_DA_SEP_STOP_ON_SENSE_DATA (0x00200107) /* SEP stopped while transferring sense data */ 238#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_1 (0x00200108) /* SEP returned unknown scsi status */ 239#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_2 (0x00200109) /* SEP returned unknown scsi status */ 240#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP (0x0020010A) /* SEP returned bad chksum after STOP */ 241#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP_GETDATA (0x0020010B) /* SEP returned bad chksum after STOP while gettin data*/ 242#define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND (0x0020010C) /* SEP doesn't support CDB opcode f/w location 1 */ 243#define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND_2 (0x0020010D) /* SEP doesn't support CDB opcode f/w location 2 */ 244#define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND_3 (0x0020010E) /* SEP doesn't support CDB opcode f/w location 3 */ 245 246/****************************************************************************/ 247/* IR LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IR */ 248/****************************************************************************/ 249#define IR_LOGINFO_RAID_ACTION_ERROR (0x00010000) 250#define IR_LOGINFO_CODE_UNUSED2 (0x00020000) 251 252/* Amount of information passed down for Create Volume is too large */ 253#define IR_LOGINFO_VOLUME_CREATE_INVALID_LENGTH (0x00010001) 254/* Creation of duplicate volume attempted (Bus/Target ID checked) */ 255#define IR_LOGINFO_VOLUME_CREATE_DUPLICATE (0x00010002) 256/* Creation failed due to maximum number of supported volumes exceeded */ 257#define IR_LOGINFO_VOLUME_CREATE_NO_SLOTS (0x00010003) 258/* Creation failed due to DMA error in trying to read from host */ 259#define IR_LOGINFO_VOLUME_CREATE_DMA_ERROR (0x00010004) 260/* Creation failed due to invalid volume type passed down */ 261#define IR_LOGINFO_VOLUME_CREATE_INVALID_VOLUME_TYPE (0x00010005) 262/* Creation failed due to error reading MFG Page 4 */ 263#define IR_LOGINFO_VOLUME_MFG_PAGE4_ERROR (0x00010006) 264/* Creation failed when trying to create internal structures */ 265#define IR_LOGINFO_VOLUME_INTERNAL_CONFIG_STRUCTURE_ERROR (0x00010007) 266 267/* Activation failed due to trying to activate an already active volume */ 268#define IR_LOGINFO_VOLUME_ACTIVATING_AN_ACTIVE_VOLUME (0x00010010) 269/* Activation failed due to trying to active unsupported volume type */ 270#define IR_LOGINFO_VOLUME_ACTIVATING_INVALID_VOLUME_TYPE (0x00010011) 271/* Activation failed due to trying to active too many volumes */ 272#define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_VOLUMES (0x00010012) 273/* Activation failed due to Volume ID in use already */ 274#define IR_LOGINFO_VOLUME_ACTIVATING_VOLUME_ID_IN_USE (0x00010013) 275/* Activation failed call to activateVolume returned failure */ 276#define IR_LOGINFO_VOLUME_ACTIVATE_VOLUME_FAILED (0x00010014) 277/* Activation failed trying to import the volume */ 278#define IR_LOGINFO_VOLUME_ACTIVATING_IMPORT_VOLUME_FAILED (0x00010015) 279/* Activation failed trying to import the volume */ 280#define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_PHYS_DISKS (0x00010016) 281 282/* Phys Disk failed, too many phys disks */ 283#define IR_LOGINFO_PHYSDISK_CREATE_TOO_MANY_DISKS (0x00010020) 284/* Amount of information passed down for Create Pnysdisk is too large */ 285#define IR_LOGINFO_PHYSDISK_CREATE_INVALID_LENGTH (0x00010021) 286/* Creation failed due to DMA error in trying to read from host */ 287#define IR_LOGINFO_PHYSDISK_CREATE_DMA_ERROR (0x00010022) 288/* Creation failed due to invalid Bus TargetID passed down */ 289#define IR_LOGINFO_PHYSDISK_CREATE_BUS_TID_INVALID (0x00010023) 290/* Creation failed due to error in creating RAID Phys Disk Config Page */ 291#define IR_LOGINFO_PHYSDISK_CREATE_CONFIG_PAGE_ERROR (0x00010024) 292 293/* Compatibility Error : IR Disabled */ 294#define IR_LOGINFO_COMPAT_ERROR_RAID_DISABLED (0x00010030) 295/* Compatibility Error : Inquiry Comand failed */ 296#define IR_LOGINFO_COMPAT_ERROR_INQUIRY_FAILED (0x00010031) 297/* Compatibility Error : Device not direct access device */ 298#define IR_LOGINFO_COMPAT_ERROR_NOT_DIRECT_ACCESS (0x00010032) 299/* Compatibility Error : Removable device found */ 300#define IR_LOGINFO_COMPAT_ERROR_REMOVABLE_FOUND (0x00010033) 301/* Compatibility Error : Device SCSI Version not 2 or higher */ 302#define IR_LOGINFO_COMPAT_ERROR_NEED_SCSI_2_OR_HIGHER (0x00010034) 303/* Compatibility Error : SATA device, 48 BIT LBA not supported */ 304#define IR_LOGINFO_COMPAT_ERROR_SATA_48BIT_LBA_NOT_SUPPORTED (0x00010035) 305/* Compatibility Error : Device does not have 512 byte block sizes */ 306#define IR_LOGINFO_COMPAT_ERROR_DEVICE_NOT_512_BYTE_BLOCK (0x00010036) 307/* Compatibility Error : Volume Type check failed */ 308#define IR_LOGINFO_COMPAT_ERROR_VOLUME_TYPE_CHECK_FAILED (0x00010037) 309/* Compatibility Error : Volume Type is unsupported by FW */ 310#define IR_LOGINFO_COMPAT_ERROR_UNSUPPORTED_VOLUME_TYPE (0x00010038) 311/* Compatibility Error : Disk drive too small for use in volume */ 312#define IR_LOGINFO_COMPAT_ERROR_DISK_TOO_SMALL (0x00010039) 313/* Compatibility Error : Phys disk for Create Volume not found */ 314#define IR_LOGINFO_COMPAT_ERROR_PHYS_DISK_NOT_FOUND (0x0001003A) 315/* Compatibility Error : membership count error, too many or too few disks for volume type */ 316#define IR_LOGINFO_COMPAT_ERROR_MEMBERSHIP_COUNT (0x0001003B) 317/* Compatibility Error : Disk stripe sizes must be 64KB */ 318#define IR_LOGINFO_COMPAT_ERROR_NON_64K_STRIPE_SIZE (0x0001003C) 319/* Compatibility Error : IME size limited to < 2TB */ 320#define IR_LOGINFO_COMPAT_ERROR_IME_VOL_NOT_CURRENTLY_SUPPORTED (0x0001003D) 321 322/* Device Firmware Update: DFU can only be started once */ 323#define IR_LOGINFO_DEV_FW_UPDATE_ERR_DFU_IN_PROGRESS (0x00010050) 324/* Device Firmware Update: Volume must be Optimal/Active/non-Quiesced */ 325#define IR_LOGINFO_DEV_FW_UPDATE_ERR_DEVICE_IN_INVALID_STATE (0x00010051) 326/* Device Firmware Update: DFU Timeout cannot be zero */ 327#define IR_LOGINFO_DEV_FW_UPDATE_ERR_INVALID_TIMEOUT (0x00010052) 328/* Device Firmware Update: CREATE TIMER FAILED */ 329#define IR_LOGINFO_DEV_FW_UPDATE_ERR_NO_TIMERS (0x00010053) 330/* Device Firmware Update: Failed to read SAS_IO_UNIT_PG_1 */ 331#define IR_LOGINFO_DEV_FW_UPDATE_ERR_READING_CFG_PAGE (0x00010054) 332/* Device Firmware Update: Invalid SAS_IO_UNIT_PG_1 value(s) */ 333#define IR_LOGINFO_DEV_FW_UPDATE_ERR_PORT_IO_TIMEOUTS_REQUIRED (0x00010055) 334/* Device Firmware Update: Unable to allocate memory for page */ 335#define IR_LOGINFO_DEV_FW_UPDATE_ERR_ALLOC_CFG_PAGE (0x00010056) 336/* Device Firmware Update: */ 337//#define IR_LOGINFO_DEV_FW_UPDATE_ERR_ (0x00010054) 338 339/****************************************************************************/ 340/* Defines for convenience */ 341/****************************************************************************/ 342#define IOC_LOGINFO_PREFIX_IOP ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IOP) 343#define IOC_LOGINFO_PREFIX_PL ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_PL) 344#define IOC_LOGINFO_PREFIX_IR ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IR) 345 346#endif /* end of file */ 347