1/*- 2 * Product specific probe and attach routines for: 3 * aic7901 and aic7902 SCSI controllers 4 * 5 * SPDX-License-Identifier: BSD-3-Clause 6 * 7 * Copyright (c) 1994-2001 Justin T. Gibbs. 8 * Copyright (c) 2000-2002 Adaptec Inc. 9 * All rights reserved. 10 * 11 * Redistribution and use in source and binary forms, with or without 12 * modification, are permitted provided that the following conditions 13 * are met: 14 * 1. Redistributions of source code must retain the above copyright 15 * notice, this list of conditions, and the following disclaimer, 16 * without modification. 17 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 18 * substantially similar to the "NO WARRANTY" disclaimer below 19 * ("Disclaimer") and any redistribution must be conditioned upon 20 * including a substantially similar Disclaimer requirement for further 21 * binary redistribution. 22 * 3. Neither the names of the above-listed copyright holders nor the names 23 * of any contributors may be used to endorse or promote products derived 24 * from this software without specific prior written permission. 25 * 26 * Alternatively, this software may be distributed under the terms of the 27 * GNU General Public License ("GPL") version 2 as published by the Free 28 * Software Foundation. 29 * 30 * NO WARRANTY 31 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 32 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 33 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR 34 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 35 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 36 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 37 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 38 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 39 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 40 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 41 * POSSIBILITY OF SUCH DAMAGES. 42 * 43 * $Id: //depot/aic7xxx/aic7xxx/aic79xx_pci.c#88 $ 44 */ 45 46#include <dev/aic7xxx/aic79xx_osm.h> 47#include <dev/aic7xxx/aic79xx_inline.h> 48 49static __inline uint64_t 50ahd_compose_id(u_int device, u_int vendor, u_int subdevice, u_int subvendor) 51{ 52 uint64_t id; 53 54 id = subvendor 55 | (subdevice << 16) 56 | ((uint64_t)vendor << 32) 57 | ((uint64_t)device << 48); 58 59 return (id); 60} 61 62#define ID_ALL_MASK 0xFFFFFFFFFFFFFFFFull 63#define ID_ALL_IROC_MASK 0xFF7FFFFFFFFFFFFFull 64#define ID_DEV_VENDOR_MASK 0xFFFFFFFF00000000ull 65#define ID_9005_GENERIC_MASK 0xFFF0FFFF00000000ull 66#define ID_9005_GENERIC_IROC_MASK 0xFF70FFFF00000000ull 67 68#define ID_AIC7901 0x800F9005FFFF9005ull 69#define ID_AHA_29320A 0x8000900500609005ull 70#define ID_AHA_29320ALP 0x8017900500449005ull 71#define ID_AHA_29320LPE 0x8017900500459005ull 72 73#define ID_AIC7901A 0x801E9005FFFF9005ull 74#define ID_AHA_29320LP 0x8014900500449005ull 75 76#define ID_AIC7902 0x801F9005FFFF9005ull 77#define ID_AIC7902_B 0x801D9005FFFF9005ull 78#define ID_AHA_39320 0x8010900500409005ull 79#define ID_AHA_29320 0x8012900500429005ull 80#define ID_AHA_29320B 0x8013900500439005ull 81#define ID_AHA_39320_B 0x8015900500409005ull 82#define ID_AHA_39320_B_DELL 0x8015900501681028ull 83#define ID_AHA_39320A 0x8016900500409005ull 84#define ID_AHA_39320D 0x8011900500419005ull 85#define ID_AHA_39320D_B 0x801C900500419005ull 86#define ID_AHA_39320D_HP 0x8011900500AC0E11ull 87#define ID_AHA_39320D_B_HP 0x801C900500AC0E11ull 88#define ID_AIC7902_PCI_REV_A4 0x3 89#define ID_AIC7902_PCI_REV_B0 0x10 90#define SUBID_HP 0x0E11 91#define DEVICE8081 0x8081 92#define DEVICE8088 0x8088 93#define DEVICE8089 0x8089 94#define ADAPTECVENDORID 0x9005 95#define SUBVENDOR9005 0x9005 96 97#define DEVID_9005_HOSTRAID(id) ((id) & 0x80) 98 99#define DEVID_9005_TYPE(id) ((id) & 0xF) 100#define DEVID_9005_TYPE_HBA 0x0 /* Standard Card */ 101#define DEVID_9005_TYPE_HBA_2EXT 0x1 /* 2 External Ports */ 102#define DEVID_9005_TYPE_MB 0xF /* On Motherboard */ 103 104#define DEVID_9005_MFUNC(id) ((id) & 0x10) 105 106#define DEVID_9005_PACKETIZED(id) ((id) & 0x8000) 107 108#define SUBID_9005_TYPE(id) ((id) & 0xF) 109#define SUBID_9005_TYPE_HBA 0x0 /* Standard Card */ 110#define SUBID_9005_TYPE_MB 0xF /* On Motherboard */ 111 112#define SUBID_9005_AUTOTERM(id) (((id) & 0x10) == 0) 113 114#define SUBID_9005_LEGACYCONN_FUNC(id) ((id) & 0x20) 115 116#define SUBID_9005_SEEPTYPE(id) ((id) & 0x0C0) >> 6) 117#define SUBID_9005_SEEPTYPE_NONE 0x0 118#define SUBID_9005_SEEPTYPE_4K 0x1 119 120static ahd_device_setup_t ahd_aic7901_setup; 121static ahd_device_setup_t ahd_aic7901A_setup; 122static ahd_device_setup_t ahd_aic7902_setup; 123static ahd_device_setup_t ahd_aic790X_setup; 124 125struct ahd_pci_identity ahd_pci_ident_table [] = 126{ 127 /* aic7901 based controllers */ 128 { 129 ID_AHA_29320A, 130 ID_ALL_MASK, 131 "Adaptec 29320A Ultra320 SCSI adapter", 132 ahd_aic7901_setup 133 }, 134 { 135 ID_AHA_29320ALP, 136 ID_ALL_MASK, 137 "Adaptec 29320ALP Ultra320 SCSI adapter", 138 ahd_aic7901_setup 139 }, 140 { 141 ID_AHA_29320LPE, 142 ID_ALL_MASK, 143 "Adaptec 29320LPE Ultra320 SCSI adapter", 144 ahd_aic7901_setup 145 }, 146 /* aic7901A based controllers */ 147 { 148 ID_AHA_29320LP, 149 ID_ALL_MASK, 150 "Adaptec 29320LP Ultra320 SCSI adapter", 151 ahd_aic7901A_setup 152 }, 153 /* aic7902 based controllers */ 154 { 155 ID_AHA_29320, 156 ID_ALL_MASK, 157 "Adaptec 29320 Ultra320 SCSI adapter", 158 ahd_aic7902_setup 159 }, 160 { 161 ID_AHA_29320B, 162 ID_ALL_MASK, 163 "Adaptec 29320B Ultra320 SCSI adapter", 164 ahd_aic7902_setup 165 }, 166 { 167 ID_AHA_39320, 168 ID_ALL_MASK, 169 "Adaptec 39320 Ultra320 SCSI adapter", 170 ahd_aic7902_setup 171 }, 172 { 173 ID_AHA_39320_B, 174 ID_ALL_MASK, 175 "Adaptec 39320 Ultra320 SCSI adapter", 176 ahd_aic7902_setup 177 }, 178 { 179 ID_AHA_39320_B_DELL, 180 ID_ALL_MASK, 181 "Adaptec (Dell OEM) 39320 Ultra320 SCSI adapter", 182 ahd_aic7902_setup 183 }, 184 { 185 ID_AHA_39320A, 186 ID_ALL_MASK, 187 "Adaptec 39320A Ultra320 SCSI adapter", 188 ahd_aic7902_setup 189 }, 190 { 191 ID_AHA_39320D, 192 ID_ALL_MASK, 193 "Adaptec 39320D Ultra320 SCSI adapter", 194 ahd_aic7902_setup 195 }, 196 { 197 ID_AHA_39320D_HP, 198 ID_ALL_MASK, 199 "Adaptec (HP OEM) 39320D Ultra320 SCSI adapter", 200 ahd_aic7902_setup 201 }, 202 { 203 ID_AHA_39320D_B, 204 ID_ALL_MASK, 205 "Adaptec 39320D Ultra320 SCSI adapter", 206 ahd_aic7902_setup 207 }, 208 { 209 ID_AHA_39320D_B_HP, 210 ID_ALL_MASK, 211 "Adaptec (HP OEM) 39320D Ultra320 SCSI adapter", 212 ahd_aic7902_setup 213 }, 214 /* Generic chip probes for devices we don't know 'exactly' */ 215 { 216 ID_AIC7901 & ID_9005_GENERIC_MASK, 217 ID_9005_GENERIC_MASK, 218 "Adaptec AIC7901 Ultra320 SCSI adapter", 219 ahd_aic7901_setup 220 }, 221 { 222 ID_AIC7901A & ID_DEV_VENDOR_MASK, 223 ID_DEV_VENDOR_MASK, 224 "Adaptec AIC7901A Ultra320 SCSI adapter", 225 ahd_aic7901A_setup 226 }, 227 { 228 ID_AIC7902 & ID_9005_GENERIC_MASK, 229 ID_9005_GENERIC_MASK, 230 "Adaptec AIC7902 Ultra320 SCSI adapter", 231 ahd_aic7902_setup 232 } 233}; 234 235const u_int ahd_num_pci_devs = NUM_ELEMENTS(ahd_pci_ident_table); 236 237#define DEVCONFIG 0x40 238#define PCIXINITPAT 0x0000E000ul 239#define PCIXINIT_PCI33_66 0x0000E000ul 240#define PCIXINIT_PCIX50_66 0x0000C000ul 241#define PCIXINIT_PCIX66_100 0x0000A000ul 242#define PCIXINIT_PCIX100_133 0x00008000ul 243#define PCI_BUS_MODES_INDEX(devconfig) \ 244 (((devconfig) & PCIXINITPAT) >> 13) 245static const char *pci_bus_modes[] = 246{ 247 "PCI bus mode unknown", 248 "PCI bus mode unknown", 249 "PCI bus mode unknown", 250 "PCI bus mode unknown", 251 "PCI-X 101-133MHz", 252 "PCI-X 67-100MHz", 253 "PCI-X 50-66MHz", 254 "PCI 33 or 66MHz" 255}; 256 257#define TESTMODE 0x00000800ul 258#define IRDY_RST 0x00000200ul 259#define FRAME_RST 0x00000100ul 260#define PCI64BIT 0x00000080ul 261#define MRDCEN 0x00000040ul 262#define ENDIANSEL 0x00000020ul 263#define MIXQWENDIANEN 0x00000008ul 264#define DACEN 0x00000004ul 265#define STPWLEVEL 0x00000002ul 266#define QWENDIANSEL 0x00000001ul 267 268#define DEVCONFIG1 0x44 269#define PREQDIS 0x01 270 271#define CSIZE_LATTIME 0x0c 272#define CACHESIZE 0x000000fful 273#define LATTIME 0x0000ff00ul 274 275static int ahd_check_extport(struct ahd_softc *ahd); 276static void ahd_configure_termination(struct ahd_softc *ahd, 277 u_int adapter_control); 278static void ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat); 279 280struct ahd_pci_identity * 281ahd_find_pci_device(aic_dev_softc_t pci) 282{ 283 uint64_t full_id; 284 uint16_t device; 285 uint16_t vendor; 286 uint16_t subdevice; 287 uint16_t subvendor; 288 struct ahd_pci_identity *entry; 289 u_int i; 290 291 vendor = aic_pci_read_config(pci, PCIR_DEVVENDOR, /*bytes*/2); 292 device = aic_pci_read_config(pci, PCIR_DEVICE, /*bytes*/2); 293 subvendor = aic_pci_read_config(pci, PCIR_SUBVEND_0, /*bytes*/2); 294 subdevice = aic_pci_read_config(pci, PCIR_SUBDEV_0, /*bytes*/2); 295 296 if ((vendor == ADAPTECVENDORID) && (subvendor == SUBVENDOR9005)) { 297 if ((device == DEVICE8081) || (device == DEVICE8088) || 298 (device == DEVICE8089)) { 299 printf("Controller device ID conflict with PMC Adaptec HBA\n"); 300 return (NULL); 301 } 302 } 303 304 full_id = ahd_compose_id(device, 305 vendor, 306 subdevice, 307 subvendor); 308 309 /* 310 * If we are configured to attach to HostRAID 311 * controllers, mask out the IROC/HostRAID bit 312 * in the 313 */ 314 if (ahd_attach_to_HostRAID_controllers) 315 full_id &= ID_ALL_IROC_MASK; 316 317 for (i = 0; i < ahd_num_pci_devs; i++) { 318 entry = &ahd_pci_ident_table[i]; 319 if (entry->full_id == (full_id & entry->id_mask)) { 320 /* Honor exclusion entries. */ 321 if (entry->name == NULL) 322 return (NULL); 323 return (entry); 324 } 325 } 326 return (NULL); 327} 328 329int 330ahd_pci_config(struct ahd_softc *ahd, struct ahd_pci_identity *entry) 331{ 332 u_int command; 333 uint32_t devconfig; 334 uint16_t device; 335 uint16_t subvendor; 336 int error; 337 338 ahd->description = entry->name; 339 /* 340 * Record if this is a HostRAID board. 341 */ 342 device = aic_pci_read_config(ahd->dev_softc, 343 PCIR_DEVICE, /*bytes*/2); 344 if (DEVID_9005_HOSTRAID(device)) 345 ahd->flags |= AHD_HOSTRAID_BOARD; 346 347 /* 348 * Record if this is an HP board. 349 */ 350 subvendor = aic_pci_read_config(ahd->dev_softc, 351 PCIR_SUBVEND_0, /*bytes*/2); 352 if (subvendor == SUBID_HP) 353 ahd->flags |= AHD_HP_BOARD; 354 355 error = entry->setup(ahd); 356 if (error != 0) 357 return (error); 358 359 /* 360 * Find the PCI-X cap pointer. If we don't find it, 361 * pcix_ptr will be 0. 362 */ 363 pci_find_cap(ahd->dev_softc, PCIY_PCIX, &ahd->pcix_ptr); 364 devconfig = aic_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); 365 if ((devconfig & PCIXINITPAT) == PCIXINIT_PCI33_66) { 366 ahd->chip |= AHD_PCI; 367 /* Disable PCIX workarounds when running in PCI mode. */ 368 ahd->bugs &= ~AHD_PCIX_BUG_MASK; 369 } else { 370 ahd->chip |= AHD_PCIX; 371 if (ahd->pcix_ptr == 0) 372 return (ENXIO); 373 } 374 ahd->bus_description = pci_bus_modes[PCI_BUS_MODES_INDEX(devconfig)]; 375 376 aic_power_state_change(ahd, AIC_POWER_STATE_D0); 377 378 error = ahd_pci_map_registers(ahd); 379 if (error != 0) 380 return (error); 381 382 /* 383 * If we need to support high memory, enable dual 384 * address cycles. This bit must be set to enable 385 * high address bit generation even if we are on a 386 * 64bit bus (PCI64BIT set in devconfig). 387 */ 388 if ((ahd->flags & (AHD_39BIT_ADDRESSING|AHD_64BIT_ADDRESSING)) != 0) { 389 uint32_t devconfig; 390 391 if (bootverbose) 392 printf("%s: Enabling 39Bit Addressing\n", 393 ahd_name(ahd)); 394 devconfig = aic_pci_read_config(ahd->dev_softc, 395 DEVCONFIG, /*bytes*/4); 396 devconfig |= DACEN; 397 aic_pci_write_config(ahd->dev_softc, DEVCONFIG, 398 devconfig, /*bytes*/4); 399 } 400 401 /* Ensure busmastering is enabled */ 402 command = aic_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2); 403 command |= PCIM_CMD_BUSMASTEREN; 404 aic_pci_write_config(ahd->dev_softc, PCIR_COMMAND, command, /*bytes*/2); 405 406 error = ahd_softc_init(ahd); 407 if (error != 0) 408 return (error); 409 410 ahd->bus_intr = ahd_pci_intr; 411 412 error = ahd_reset(ahd, /*reinit*/FALSE); 413 if (error != 0) 414 return (ENXIO); 415 416 ahd->pci_cachesize = 417 aic_pci_read_config(ahd->dev_softc, CSIZE_LATTIME, 418 /*bytes*/1) & CACHESIZE; 419 ahd->pci_cachesize *= 4; 420 421 ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); 422 /* See if we have a SEEPROM and perform auto-term */ 423 error = ahd_check_extport(ahd); 424 if (error != 0) 425 return (error); 426 427 /* Core initialization */ 428 error = ahd_init(ahd); 429 if (error != 0) 430 return (error); 431 432 /* 433 * Allow interrupts now that we are completely setup. 434 */ 435 error = ahd_pci_map_int(ahd); 436 if (error != 0) 437 return (error); 438 439 ahd_lock(ahd); 440 /* 441 * Link this softc in with all other ahd instances. 442 */ 443 ahd_softc_insert(ahd); 444 ahd_unlock(ahd); 445 return (0); 446} 447 448/* 449 * Perform some simple tests that should catch situations where 450 * our registers are invalidly mapped. 451 */ 452int 453ahd_pci_test_register_access(struct ahd_softc *ahd) 454{ 455 uint32_t cmd; 456 u_int targpcistat; 457 u_int pci_status1; 458 int error; 459 uint8_t hcntrl; 460 461 error = EIO; 462 463 /* 464 * Enable PCI error interrupt status, but suppress NMIs 465 * generated by SERR raised due to target aborts. 466 */ 467 cmd = aic_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2); 468 aic_pci_write_config(ahd->dev_softc, PCIR_COMMAND, 469 cmd & ~PCIM_CMD_SERRESPEN, /*bytes*/2); 470 471 /* 472 * First a simple test to see if any 473 * registers can be read. Reading 474 * HCNTRL has no side effects and has 475 * at least one bit that is guaranteed to 476 * be zero so it is a good register to 477 * use for this test. 478 */ 479 hcntrl = ahd_inb(ahd, HCNTRL); 480 if (hcntrl == 0xFF) 481 goto fail; 482 483 /* 484 * Next create a situation where write combining 485 * or read prefetching could be initiated by the 486 * CPU or host bridge. Our device does not support 487 * either, so look for data corruption and/or flagged 488 * PCI errors. First pause without causing another 489 * chip reset. 490 */ 491 hcntrl &= ~CHIPRST; 492 ahd_outb(ahd, HCNTRL, hcntrl|PAUSE); 493 while (ahd_is_paused(ahd) == 0) 494 ; 495 496 /* Clear any PCI errors that occurred before our driver attached. */ 497 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 498 targpcistat = ahd_inb(ahd, TARGPCISTAT); 499 ahd_outb(ahd, TARGPCISTAT, targpcistat); 500 pci_status1 = aic_pci_read_config(ahd->dev_softc, 501 PCIR_STATUS + 1, /*bytes*/1); 502 aic_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, 503 pci_status1, /*bytes*/1); 504 ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); 505 ahd_outb(ahd, CLRINT, CLRPCIINT); 506 507 ahd_outb(ahd, SEQCTL0, PERRORDIS); 508 ahd_outl(ahd, SRAM_BASE, 0x5aa555aa); 509 if (ahd_inl(ahd, SRAM_BASE) != 0x5aa555aa) 510 goto fail; 511 512 if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) { 513 u_int targpcistat; 514 515 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 516 targpcistat = ahd_inb(ahd, TARGPCISTAT); 517 if ((targpcistat & STA) != 0) 518 goto fail; 519 } 520 521 error = 0; 522 523fail: 524 if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) { 525 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 526 targpcistat = ahd_inb(ahd, TARGPCISTAT); 527 528 /* Silently clear any latched errors. */ 529 ahd_outb(ahd, TARGPCISTAT, targpcistat); 530 pci_status1 = aic_pci_read_config(ahd->dev_softc, 531 PCIR_STATUS + 1, /*bytes*/1); 532 aic_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, 533 pci_status1, /*bytes*/1); 534 ahd_outb(ahd, CLRINT, CLRPCIINT); 535 } 536 ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS); 537 aic_pci_write_config(ahd->dev_softc, PCIR_COMMAND, cmd, /*bytes*/2); 538 return (error); 539} 540 541/* 542 * Check the external port logic for a serial eeprom 543 * and termination/cable detection contrls. 544 */ 545static int 546ahd_check_extport(struct ahd_softc *ahd) 547{ 548 struct vpd_config vpd; 549 struct seeprom_config *sc; 550 u_int adapter_control; 551 int have_seeprom; 552 int error; 553 554 sc = ahd->seep_config; 555 have_seeprom = ahd_acquire_seeprom(ahd); 556 if (have_seeprom) { 557 u_int start_addr; 558 559 /* 560 * Fetch VPD for this function and parse it. 561 */ 562 if (bootverbose) 563 printf("%s: Reading VPD from SEEPROM...", 564 ahd_name(ahd)); 565 566 /* Address is always in units of 16bit words */ 567 start_addr = ((2 * sizeof(*sc)) 568 + (sizeof(vpd) * (ahd->channel - 'A'))) / 2; 569 570 error = ahd_read_seeprom(ahd, (uint16_t *)&vpd, 571 start_addr, sizeof(vpd)/2, 572 /*bytestream*/TRUE); 573 if (error == 0) 574 error = ahd_parse_vpddata(ahd, &vpd); 575 if (bootverbose) 576 printf("%s: VPD parsing %s\n", 577 ahd_name(ahd), 578 error == 0 ? "successful" : "failed"); 579 580 if (bootverbose) 581 printf("%s: Reading SEEPROM...", ahd_name(ahd)); 582 583 /* Address is always in units of 16bit words */ 584 start_addr = (sizeof(*sc) / 2) * (ahd->channel - 'A'); 585 586 error = ahd_read_seeprom(ahd, (uint16_t *)sc, 587 start_addr, sizeof(*sc)/2, 588 /*bytestream*/FALSE); 589 590 if (error != 0) { 591 printf("Unable to read SEEPROM\n"); 592 have_seeprom = 0; 593 } else { 594 have_seeprom = ahd_verify_cksum(sc); 595 596 if (bootverbose) { 597 if (have_seeprom == 0) 598 printf ("checksum error\n"); 599 else 600 printf ("done.\n"); 601 } 602 } 603 ahd_release_seeprom(ahd); 604 } 605 606 if (!have_seeprom) { 607 u_int nvram_scb; 608 609 /* 610 * Pull scratch ram settings and treat them as 611 * if they are the contents of an seeprom if 612 * the 'ADPT', 'BIOS', or 'ASPI' signature is found 613 * in SCB 0xFF. We manually compose the data as 16bit 614 * values to avoid endian issues. 615 */ 616 ahd_set_scbptr(ahd, 0xFF); 617 nvram_scb = ahd_inb_scbram(ahd, SCB_BASE + NVRAM_SCB_OFFSET); 618 if (nvram_scb != 0xFF 619 && ((ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A' 620 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'D' 621 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P' 622 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'T') 623 || (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'B' 624 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'I' 625 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'O' 626 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'S') 627 || (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A' 628 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'S' 629 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P' 630 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'I'))) { 631 uint16_t *sc_data; 632 int i; 633 634 ahd_set_scbptr(ahd, nvram_scb); 635 sc_data = (uint16_t *)sc; 636 for (i = 0; i < 64; i += 2) 637 *sc_data++ = ahd_inw_scbram(ahd, SCB_BASE+i); 638 have_seeprom = ahd_verify_cksum(sc); 639 if (have_seeprom) 640 ahd->flags |= AHD_SCB_CONFIG_USED; 641 } 642 } 643 644#ifdef AHD_DEBUG 645 if (have_seeprom != 0 646 && (ahd_debug & AHD_DUMP_SEEPROM) != 0) { 647 uint16_t *sc_data; 648 int i; 649 650 printf("%s: Seeprom Contents:", ahd_name(ahd)); 651 sc_data = (uint16_t *)sc; 652 for (i = 0; i < (sizeof(*sc)); i += 2) 653 printf("\n\t0x%.4x", sc_data[i]); 654 printf("\n"); 655 } 656#endif 657 658 if (!have_seeprom) { 659 if (bootverbose) 660 printf("%s: No SEEPROM available.\n", ahd_name(ahd)); 661 ahd->flags |= AHD_USEDEFAULTS; 662 error = ahd_default_config(ahd); 663 adapter_control = CFAUTOTERM|CFSEAUTOTERM; 664 free(ahd->seep_config, M_DEVBUF); 665 ahd->seep_config = NULL; 666 } else { 667 error = ahd_parse_cfgdata(ahd, sc); 668 adapter_control = sc->adapter_control; 669 } 670 if (error != 0) 671 return (error); 672 673 ahd_configure_termination(ahd, adapter_control); 674 675 return (0); 676} 677 678static void 679ahd_configure_termination(struct ahd_softc *ahd, u_int adapter_control) 680{ 681 int error; 682 u_int sxfrctl1; 683 uint8_t termctl; 684 uint32_t devconfig; 685 686 devconfig = aic_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); 687 devconfig &= ~STPWLEVEL; 688 if ((ahd->flags & AHD_STPWLEVEL_A) != 0) 689 devconfig |= STPWLEVEL; 690 if (bootverbose) 691 printf("%s: STPWLEVEL is %s\n", 692 ahd_name(ahd), (devconfig & STPWLEVEL) ? "on" : "off"); 693 aic_pci_write_config(ahd->dev_softc, DEVCONFIG, devconfig, /*bytes*/4); 694 695 /* Make sure current sensing is off. */ 696 if ((ahd->flags & AHD_CURRENT_SENSING) != 0) { 697 (void)ahd_write_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL, 0); 698 } 699 700 /* 701 * Read to sense. Write to set. 702 */ 703 error = ahd_read_flexport(ahd, FLXADDR_TERMCTL, &termctl); 704 if ((adapter_control & CFAUTOTERM) == 0) { 705 if (bootverbose) 706 printf("%s: Manual Primary Termination\n", 707 ahd_name(ahd)); 708 termctl &= ~(FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH); 709 if ((adapter_control & CFSTERM) != 0) 710 termctl |= FLX_TERMCTL_ENPRILOW; 711 if ((adapter_control & CFWSTERM) != 0) 712 termctl |= FLX_TERMCTL_ENPRIHIGH; 713 } else if (error != 0) { 714 printf("%s: Primary Auto-Term Sensing failed! " 715 "Using Defaults.\n", ahd_name(ahd)); 716 termctl = FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH; 717 } 718 719 if ((adapter_control & CFSEAUTOTERM) == 0) { 720 if (bootverbose) 721 printf("%s: Manual Secondary Termination\n", 722 ahd_name(ahd)); 723 termctl &= ~(FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH); 724 if ((adapter_control & CFSELOWTERM) != 0) 725 termctl |= FLX_TERMCTL_ENSECLOW; 726 if ((adapter_control & CFSEHIGHTERM) != 0) 727 termctl |= FLX_TERMCTL_ENSECHIGH; 728 } else if (error != 0) { 729 printf("%s: Secondary Auto-Term Sensing failed! " 730 "Using Defaults.\n", ahd_name(ahd)); 731 termctl |= FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH; 732 } 733 734 /* 735 * Now set the termination based on what we found. 736 */ 737 sxfrctl1 = ahd_inb(ahd, SXFRCTL1) & ~STPWEN; 738 ahd->flags &= ~AHD_TERM_ENB_A; 739 if ((termctl & FLX_TERMCTL_ENPRILOW) != 0) { 740 ahd->flags |= AHD_TERM_ENB_A; 741 sxfrctl1 |= STPWEN; 742 } 743 /* Must set the latch once in order to be effective. */ 744 ahd_outb(ahd, SXFRCTL1, sxfrctl1|STPWEN); 745 ahd_outb(ahd, SXFRCTL1, sxfrctl1); 746 747 error = ahd_write_flexport(ahd, FLXADDR_TERMCTL, termctl); 748 if (error != 0) { 749 printf("%s: Unable to set termination settings!\n", 750 ahd_name(ahd)); 751 } else if (bootverbose) { 752 printf("%s: Primary High byte termination %sabled\n", 753 ahd_name(ahd), 754 (termctl & FLX_TERMCTL_ENPRIHIGH) ? "En" : "Dis"); 755 756 printf("%s: Primary Low byte termination %sabled\n", 757 ahd_name(ahd), 758 (termctl & FLX_TERMCTL_ENPRILOW) ? "En" : "Dis"); 759 760 printf("%s: Secondary High byte termination %sabled\n", 761 ahd_name(ahd), 762 (termctl & FLX_TERMCTL_ENSECHIGH) ? "En" : "Dis"); 763 764 printf("%s: Secondary Low byte termination %sabled\n", 765 ahd_name(ahd), 766 (termctl & FLX_TERMCTL_ENSECLOW) ? "En" : "Dis"); 767 } 768 return; 769} 770 771#define DPE 0x80 772#define SSE 0x40 773#define RMA 0x20 774#define RTA 0x10 775#define STA 0x08 776#define DPR 0x01 777 778static const char *split_status_source[] = 779{ 780 "DFF0", 781 "DFF1", 782 "OVLY", 783 "CMC", 784}; 785 786static const char *pci_status_source[] = 787{ 788 "DFF0", 789 "DFF1", 790 "SG", 791 "CMC", 792 "OVLY", 793 "NONE", 794 "MSI", 795 "TARG" 796}; 797 798static const char *split_status_strings[] = 799{ 800 "%s: Received split response in %s.\n", 801 "%s: Received split completion error message in %s\n", 802 "%s: Receive overrun in %s\n", 803 "%s: Count not complete in %s\n", 804 "%s: Split completion data bucket in %s\n", 805 "%s: Split completion address error in %s\n", 806 "%s: Split completion byte count error in %s\n", 807 "%s: Signaled Target-abort to early terminate a split in %s\n" 808}; 809 810static const char *pci_status_strings[] = 811{ 812 "%s: Data Parity Error has been reported via PERR# in %s\n", 813 "%s: Target initial wait state error in %s\n", 814 "%s: Split completion read data parity error in %s\n", 815 "%s: Split completion address attribute parity error in %s\n", 816 "%s: Received a Target Abort in %s\n", 817 "%s: Received a Master Abort in %s\n", 818 "%s: Signal System Error Detected in %s\n", 819 "%s: Address or Write Phase Parity Error Detected in %s.\n" 820}; 821 822void 823ahd_pci_intr(struct ahd_softc *ahd) 824{ 825 uint8_t pci_status[8]; 826 ahd_mode_state saved_modes; 827 u_int pci_status1; 828 u_int intstat; 829 u_int i; 830 u_int reg; 831 832 intstat = ahd_inb(ahd, INTSTAT); 833 834 if ((intstat & SPLTINT) != 0) 835 ahd_pci_split_intr(ahd, intstat); 836 837 if ((intstat & PCIINT) == 0) 838 return; 839 840 printf("%s: PCI error Interrupt\n", ahd_name(ahd)); 841 saved_modes = ahd_save_modes(ahd); 842 ahd_dump_card_state(ahd); 843 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 844 for (i = 0, reg = DF0PCISTAT; i < 8; i++, reg++) { 845 if (i == 5) 846 continue; 847 pci_status[i] = ahd_inb(ahd, reg); 848 /* Clear latched errors. So our interrupt deasserts. */ 849 ahd_outb(ahd, reg, pci_status[i]); 850 } 851 852 for (i = 0; i < 8; i++) { 853 u_int bit; 854 855 if (i == 5) 856 continue; 857 858 for (bit = 0; bit < 8; bit++) { 859 if ((pci_status[i] & (0x1 << bit)) != 0) { 860 static const char *s; 861 862 s = pci_status_strings[bit]; 863 if (i == 7/*TARG*/ && bit == 3) 864 s = "%s: Signaled Target Abort\n"; 865 printf(s, ahd_name(ahd), pci_status_source[i]); 866 } 867 } 868 } 869 pci_status1 = aic_pci_read_config(ahd->dev_softc, 870 PCIR_STATUS + 1, /*bytes*/1); 871 aic_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, 872 pci_status1, /*bytes*/1); 873 ahd_restore_modes(ahd, saved_modes); 874 ahd_outb(ahd, CLRINT, CLRPCIINT); 875 ahd_unpause(ahd); 876} 877 878static void 879ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat) 880{ 881 uint8_t split_status[4]; 882 uint8_t split_status1[4]; 883 uint8_t sg_split_status[2]; 884 uint8_t sg_split_status1[2]; 885 ahd_mode_state saved_modes; 886 u_int i; 887 uint32_t pcix_status; 888 889 /* 890 * Check for splits in all modes. Modes 0 and 1 891 * additionally have SG engine splits to look at. 892 */ 893 pcix_status = aic_pci_read_config(ahd->dev_softc, 894 ahd->pcix_ptr + PCIXR_STATUS, /*bytes*/ 4); 895 printf("%s: PCI Split Interrupt - PCI-X status = 0x%x\n", 896 ahd_name(ahd), pcix_status >> 16); 897 saved_modes = ahd_save_modes(ahd); 898 for (i = 0; i < 4; i++) { 899 ahd_set_modes(ahd, i, i); 900 901 split_status[i] = ahd_inb(ahd, DCHSPLTSTAT0); 902 split_status1[i] = ahd_inb(ahd, DCHSPLTSTAT1); 903 /* Clear latched errors. So our interrupt deasserts. */ 904 ahd_outb(ahd, DCHSPLTSTAT0, split_status[i]); 905 ahd_outb(ahd, DCHSPLTSTAT1, split_status1[i]); 906 if (i > 1) 907 continue; 908 sg_split_status[i] = ahd_inb(ahd, SGSPLTSTAT0); 909 sg_split_status1[i] = ahd_inb(ahd, SGSPLTSTAT1); 910 /* Clear latched errors. So our interrupt deasserts. */ 911 ahd_outb(ahd, SGSPLTSTAT0, sg_split_status[i]); 912 ahd_outb(ahd, SGSPLTSTAT1, sg_split_status1[i]); 913 } 914 915 for (i = 0; i < 4; i++) { 916 u_int bit; 917 918 for (bit = 0; bit < 8; bit++) { 919 if ((split_status[i] & (0x1 << bit)) != 0) { 920 static const char *s; 921 922 s = split_status_strings[bit]; 923 printf(s, ahd_name(ahd), 924 split_status_source[i]); 925 } 926 927 if (i > 1) 928 continue; 929 930 if ((sg_split_status[i] & (0x1 << bit)) != 0) { 931 static const char *s; 932 933 s = split_status_strings[bit]; 934 printf(s, ahd_name(ahd), "SG"); 935 } 936 } 937 } 938 /* 939 * Clear PCI-X status bits. 940 */ 941 aic_pci_write_config(ahd->dev_softc, ahd->pcix_ptr + PCIXR_STATUS, 942 pcix_status, /*bytes*/4); 943 ahd_outb(ahd, CLRINT, CLRSPLTINT); 944 ahd_restore_modes(ahd, saved_modes); 945} 946 947static int 948ahd_aic7901_setup(struct ahd_softc *ahd) 949{ 950 951 ahd->chip = AHD_AIC7901; 952 ahd->features = AHD_AIC7901_FE; 953 return (ahd_aic790X_setup(ahd)); 954} 955 956static int 957ahd_aic7901A_setup(struct ahd_softc *ahd) 958{ 959 960 ahd->chip = AHD_AIC7901A; 961 ahd->features = AHD_AIC7901A_FE; 962 return (ahd_aic790X_setup(ahd)); 963} 964 965static int 966ahd_aic7902_setup(struct ahd_softc *ahd) 967{ 968 ahd->chip = AHD_AIC7902; 969 ahd->features = AHD_AIC7902_FE; 970 return (ahd_aic790X_setup(ahd)); 971} 972 973static int 974ahd_aic790X_setup(struct ahd_softc *ahd) 975{ 976 aic_dev_softc_t pci; 977 u_int rev; 978 979 pci = ahd->dev_softc; 980 rev = aic_pci_read_config(pci, PCIR_REVID, /*bytes*/1); 981 if (rev < ID_AIC7902_PCI_REV_A4) { 982 printf("%s: Unable to attach to unsupported chip revision %d\n", 983 ahd_name(ahd), rev); 984 aic_pci_write_config(pci, PCIR_COMMAND, 0, /*bytes*/2); 985 return (ENXIO); 986 } 987 ahd->channel = aic_get_pci_function(pci) + 'A'; 988 if (rev < ID_AIC7902_PCI_REV_B0) { 989 /* 990 * Enable A series workarounds. 991 */ 992 ahd->bugs |= AHD_SENT_SCB_UPDATE_BUG|AHD_ABORT_LQI_BUG 993 | AHD_PKT_BITBUCKET_BUG|AHD_LONG_SETIMO_BUG 994 | AHD_NLQICRC_DELAYED_BUG|AHD_SCSIRST_BUG 995 | AHD_LQO_ATNO_BUG|AHD_AUTOFLUSH_BUG 996 | AHD_CLRLQO_AUTOCLR_BUG|AHD_PCIX_MMAPIO_BUG 997 | AHD_PCIX_CHIPRST_BUG|AHD_PCIX_SCBRAM_RD_BUG 998 | AHD_PKTIZED_STATUS_BUG|AHD_PKT_LUN_BUG 999 | AHD_MDFF_WSCBPTR_BUG|AHD_REG_SLOW_SETTLE_BUG 1000 | AHD_SET_MODE_BUG|AHD_BUSFREEREV_BUG 1001 | AHD_NONPACKFIFO_BUG|AHD_PACED_NEGTABLE_BUG 1002 | AHD_FAINT_LED_BUG; 1003 1004 /* 1005 * IO Cell parameter setup. 1006 */ 1007 AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29); 1008 1009 if ((ahd->flags & AHD_HP_BOARD) == 0) 1010 AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVA); 1011 } else { 1012 u_int devconfig1; 1013 1014 ahd->features |= AHD_RTI|AHD_NEW_IOCELL_OPTS 1015 | AHD_NEW_DFCNTRL_OPTS|AHD_FAST_CDB_DELIVERY; 1016 ahd->bugs |= AHD_LQOOVERRUN_BUG|AHD_EARLY_REQ_BUG; 1017 1018 /* 1019 * Some issues have been resolved in the 7901B. 1020 */ 1021 if ((ahd->features & AHD_MULTI_FUNC) != 0) 1022 ahd->bugs |= AHD_INTCOLLISION_BUG|AHD_ABORT_LQI_BUG 1023 | AHD_BUSFREEREV_BUG; 1024 1025 /* 1026 * IO Cell parameter setup. 1027 */ 1028 AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29); 1029 AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVB); 1030 AHD_SET_AMPLITUDE(ahd, AHD_AMPLITUDE_DEF); 1031 1032 /* 1033 * Set the PREQDIS bit for H2B which disables some workaround 1034 * that doesn't work on regular PCI busses. 1035 * XXX - Find out exactly what this does from the hardware 1036 * folks! 1037 */ 1038 devconfig1 = aic_pci_read_config(pci, DEVCONFIG1, /*bytes*/1); 1039 aic_pci_write_config(pci, DEVCONFIG1, 1040 devconfig1|PREQDIS, /*bytes*/1); 1041 devconfig1 = aic_pci_read_config(pci, DEVCONFIG1, /*bytes*/1); 1042 } 1043 1044 return (0); 1045} 1046