1/* 2******************************************************************************** 3** OS : FreeBSD 4** FILE NAME : arcmsr.h 5** BY : Erich Chen, Ching Huang 6** Description: SCSI RAID Device Driver for 7** ARECA (ARC11XX/ARC12XX/ARC13XX/ARC16XX/ARC188x) 8** SATA/SAS RAID HOST Adapter 9******************************************************************************** 10******************************************************************************** 11** Copyright (C) 2002 - 2012, Areca Technology Corporation All rights reserved. 12** 13** Redistribution and use in source and binary forms,with or without 14** modification,are permitted provided that the following conditions 15** are met: 16** 1. Redistributions of source code must retain the above copyright 17** notice,this list of conditions and the following disclaimer. 18** 2. Redistributions in binary form must reproduce the above copyright 19** notice,this list of conditions and the following disclaimer in the 20** documentation and/or other materials provided with the distribution. 21** 3. The name of the author may not be used to endorse or promote products 22** derived from this software without specific prior written permission. 23** 24** THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 25** IMPLIED WARRANTIES,INCLUDING,BUT NOT LIMITED TO,THE IMPLIED WARRANTIES 26** OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 27** IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,INDIRECT, 28** INCIDENTAL,SPECIAL,EXEMPLARY,OR CONSEQUENTIAL DAMAGES(INCLUDING,BUT 29** NOT LIMITED TO,PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 30** DATA,OR PROFITS; OR BUSINESS INTERRUPTION)HOWEVER CAUSED AND ON ANY 31** THEORY OF LIABILITY,WHETHER IN CONTRACT,STRICT LIABILITY,OR TORT 32**(INCLUDING NEGLIGENCE OR OTHERWISE)ARISING IN ANY WAY OUT OF THE USE OF 33** THIS SOFTWARE,EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 34************************************************************************** 35* $FreeBSD$ 36*/ 37#define ARCMSR_SCSI_INITIATOR_ID 255 38#define ARCMSR_DEV_SECTOR_SIZE 512 39#define ARCMSR_MAX_XFER_SECTORS 4096 40#define ARCMSR_MAX_TARGETID 17 /*16 max target id + 1*/ 41#define ARCMSR_MAX_TARGETLUN 8 /*8*/ 42#define ARCMSR_MAX_CHIPTYPE_NUM 4 43#define ARCMSR_MAX_OUTSTANDING_CMD 256 44#define ARCMSR_MAX_START_JOB 256 45#define ARCMSR_MAX_CMD_PERLUN ARCMSR_MAX_OUTSTANDING_CMD 46#define ARCMSR_MAX_FREESRB_NUM 384 47#define ARCMSR_MAX_QBUFFER 4096 /* ioctl QBUFFER */ 48#define ARCMSR_MAX_SG_ENTRIES 38 /* max 38*/ 49#define ARCMSR_MAX_ADAPTER 4 50#define ARCMSR_RELEASE_SIMQ_LEVEL 230 51#define ARCMSR_MAX_HBB_POSTQUEUE 264 /* (ARCMSR_MAX_OUTSTANDING_CMD+8) */ 52#define ARCMSR_MAX_HBD_POSTQUEUE 256 53#define ARCMSR_TIMEOUT_DELAY 60 /* in sec */ 54/* 55********************************************************************* 56*/ 57#ifndef TRUE 58 #define TRUE 1 59#endif 60#ifndef FALSE 61 #define FALSE 0 62#endif 63#ifndef INTR_ENTROPY 64 # define INTR_ENTROPY 0 65#endif 66 67#ifndef offsetof 68 #define offsetof(type, member) ((size_t)(&((type *)0)->member)) 69#endif 70 71#if __FreeBSD_version >= 500005 72 #define ARCMSR_LOCK_INIT(l, s) mtx_init(l, s, NULL, MTX_DEF) 73 #define ARCMSR_LOCK_DESTROY(l) mtx_destroy(l) 74 #define ARCMSR_LOCK_ACQUIRE(l) mtx_lock(l) 75 #define ARCMSR_LOCK_RELEASE(l) mtx_unlock(l) 76 #define ARCMSR_LOCK_TRY(l) mtx_trylock(l) 77 #define arcmsr_htole32(x) htole32(x) 78 typedef struct mtx arcmsr_lock_t; 79#else 80 #define ARCMSR_LOCK_INIT(l, s) simple_lock_init(l) 81 #define ARCMSR_LOCK_DESTROY(l) 82 #define ARCMSR_LOCK_ACQUIRE(l) simple_lock(l) 83 #define ARCMSR_LOCK_RELEASE(l) simple_unlock(l) 84 #define ARCMSR_LOCK_TRY(l) simple_lock_try(l) 85 #define arcmsr_htole32(x) (x) 86 typedef struct simplelock arcmsr_lock_t; 87#endif 88 89/* 90********************************************************************************** 91** 92********************************************************************************** 93*/ 94#define PCI_VENDOR_ID_ARECA 0x17D3 /* Vendor ID */ 95#define PCI_DEVICE_ID_ARECA_1110 0x1110 /* Device ID */ 96#define PCI_DEVICE_ID_ARECA_1120 0x1120 /* Device ID */ 97#define PCI_DEVICE_ID_ARECA_1130 0x1130 /* Device ID */ 98#define PCI_DEVICE_ID_ARECA_1160 0x1160 /* Device ID */ 99#define PCI_DEVICE_ID_ARECA_1170 0x1170 /* Device ID */ 100#define PCI_DEVICE_ID_ARECA_1200 0x1200 /* Device ID */ 101#define PCI_DEVICE_ID_ARECA_1201 0x1201 /* Device ID */ 102#define PCI_DEVICE_ID_ARECA_1210 0x1210 /* Device ID */ 103#define PCI_DEVICE_ID_ARECA_1212 0x1212 /* Device ID */ 104#define PCI_DEVICE_ID_ARECA_1214 0x1214 /* Device ID */ 105#define PCI_DEVICE_ID_ARECA_1220 0x1220 /* Device ID */ 106#define PCI_DEVICE_ID_ARECA_1222 0x1222 /* Device ID */ 107#define PCI_DEVICE_ID_ARECA_1230 0x1230 /* Device ID */ 108#define PCI_DEVICE_ID_ARECA_1231 0x1231 /* Device ID */ 109#define PCI_DEVICE_ID_ARECA_1260 0x1260 /* Device ID */ 110#define PCI_DEVICE_ID_ARECA_1261 0x1261 /* Device ID */ 111#define PCI_DEVICE_ID_ARECA_1270 0x1270 /* Device ID */ 112#define PCI_DEVICE_ID_ARECA_1280 0x1280 /* Device ID */ 113#define PCI_DEVICE_ID_ARECA_1380 0x1380 /* Device ID */ 114#define PCI_DEVICE_ID_ARECA_1381 0x1381 /* Device ID */ 115#define PCI_DEVICE_ID_ARECA_1680 0x1680 /* Device ID */ 116#define PCI_DEVICE_ID_ARECA_1681 0x1681 /* Device ID */ 117#define PCI_DEVICE_ID_ARECA_1880 0x1880 /* Device ID */ 118 119#define ARECA_SUB_DEV_ID_1880 0x1880 /* Subsystem Device ID */ 120#define ARECA_SUB_DEV_ID_1882 0x1882 /* Subsystem Device ID */ 121#define ARECA_SUB_DEV_ID_1212 0x1212 /* Subsystem Device ID */ 122#define ARECA_SUB_DEV_ID_1213 0x1213 /* Subsystem Device ID */ 123#define ARECA_SUB_DEV_ID_1222 0x1222 /* Subsystem Device ID */ 124#define ARECA_SUB_DEV_ID_1223 0x1223 /* Subsystem Device ID */ 125 126#define PCIDevVenIDARC1110 0x111017D3 /* Vendor Device ID */ 127#define PCIDevVenIDARC1120 0x112017D3 /* Vendor Device ID */ 128#define PCIDevVenIDARC1130 0x113017D3 /* Vendor Device ID */ 129#define PCIDevVenIDARC1160 0x116017D3 /* Vendor Device ID */ 130#define PCIDevVenIDARC1170 0x117017D3 /* Vendor Device ID */ 131#define PCIDevVenIDARC1200 0x120017D3 /* Vendor Device ID */ 132#define PCIDevVenIDARC1201 0x120117D3 /* Vendor Device ID */ 133#define PCIDevVenIDARC1210 0x121017D3 /* Vendor Device ID */ 134#define PCIDevVenIDARC1212 0x121217D3 /* Vendor Device ID */ 135#define PCIDevVenIDARC1213 0x121317D3 /* Vendor Device ID */ 136#define PCIDevVenIDARC1214 0x121417D3 /* Vendor Device ID */ 137#define PCIDevVenIDARC1220 0x122017D3 /* Vendor Device ID */ 138#define PCIDevVenIDARC1222 0x122217D3 /* Vendor Device ID */ 139#define PCIDevVenIDARC1223 0x122317D3 /* Vendor Device ID */ 140#define PCIDevVenIDARC1230 0x123017D3 /* Vendor Device ID */ 141#define PCIDevVenIDARC1231 0x123117D3 /* Vendor Device ID */ 142#define PCIDevVenIDARC1260 0x126017D3 /* Vendor Device ID */ 143#define PCIDevVenIDARC1261 0x126117D3 /* Vendor Device ID */ 144#define PCIDevVenIDARC1270 0x127017D3 /* Vendor Device ID */ 145#define PCIDevVenIDARC1280 0x128017D3 /* Vendor Device ID */ 146#define PCIDevVenIDARC1380 0x138017D3 /* Vendor Device ID */ 147#define PCIDevVenIDARC1381 0x138117D3 /* Vendor Device ID */ 148#define PCIDevVenIDARC1680 0x168017D3 /* Vendor Device ID */ 149#define PCIDevVenIDARC1681 0x168117D3 /* Vendor Device ID */ 150#define PCIDevVenIDARC1880 0x188017D3 /* Vendor Device ID */ 151#define PCIDevVenIDARC1882 0x188217D3 /* Vendor Device ID */ 152 153#ifndef PCIR_BARS 154 #define PCIR_BARS 0x10 155 #define PCIR_BAR(x) (PCIR_BARS + (x) * 4) 156#endif 157 158#define PCI_BASE_ADDR0 0x10 159#define PCI_BASE_ADDR1 0x14 160#define PCI_BASE_ADDR2 0x18 161#define PCI_BASE_ADDR3 0x1C 162#define PCI_BASE_ADDR4 0x20 163#define PCI_BASE_ADDR5 0x24 164/* 165********************************************************************************** 166** 167********************************************************************************** 168*/ 169#define ARCMSR_SCSICMD_IOCTL 0x77 170#define ARCMSR_CDEVSW_IOCTL 0x88 171#define ARCMSR_MESSAGE_FAIL 0x0001 172#define ARCMSR_MESSAGE_SUCCESS 0x0000 173/* 174********************************************************************************** 175** 176********************************************************************************** 177*/ 178#define arcmsr_ccbsrb_ptr spriv_ptr0 179#define arcmsr_ccbacb_ptr spriv_ptr1 180#define dma_addr_hi32(addr) (u_int32_t) ((addr>>16)>>16) 181#define dma_addr_lo32(addr) (u_int32_t) (addr & 0xffffffff) 182#define get_min(x,y) ((x) < (y) ? (x) : (y)) 183#define get_max(x,y) ((x) < (y) ? (y) : (x)) 184/* 185************************************************************************** 186************************************************************************** 187*/ 188#define CHIP_REG_READ32(s, b, r) bus_space_read_4(acb->btag[b], acb->bhandle[b], offsetof(struct s, r)) 189#define CHIP_REG_WRITE32(s, b, r, d) bus_space_write_4(acb->btag[b], acb->bhandle[b], offsetof(struct s, r), d) 190/* 191********************************************************************************** 192** IOCTL CONTROL Mail Box 193********************************************************************************** 194*/ 195struct CMD_MESSAGE { 196 u_int32_t HeaderLength; 197 u_int8_t Signature[8]; 198 u_int32_t Timeout; 199 u_int32_t ControlCode; 200 u_int32_t ReturnCode; 201 u_int32_t Length; 202}; 203 204struct CMD_MESSAGE_FIELD { 205 struct CMD_MESSAGE cmdmessage; /* ioctl header */ 206 u_int8_t messagedatabuffer[1032]; /* areca gui program does not accept more than 1031 byte */ 207}; 208 209/************************************************************************/ 210/************************************************************************/ 211 212#define ARCMSR_IOP_ERROR_ILLEGALPCI 0x0001 213#define ARCMSR_IOP_ERROR_VENDORID 0x0002 214#define ARCMSR_IOP_ERROR_DEVICEID 0x0002 215#define ARCMSR_IOP_ERROR_ILLEGALCDB 0x0003 216#define ARCMSR_IOP_ERROR_UNKNOW_CDBERR 0x0004 217#define ARCMSR_SYS_ERROR_MEMORY_ALLOCATE 0x0005 218#define ARCMSR_SYS_ERROR_MEMORY_CROSS4G 0x0006 219#define ARCMSR_SYS_ERROR_MEMORY_LACK 0x0007 220#define ARCMSR_SYS_ERROR_MEMORY_RANGE 0x0008 221#define ARCMSR_SYS_ERROR_DEVICE_BASE 0x0009 222#define ARCMSR_SYS_ERROR_PORT_VALIDATE 0x000A 223 224/*DeviceType*/ 225#define ARECA_SATA_RAID 0x90000000 226 227/*FunctionCode*/ 228#define FUNCTION_READ_RQBUFFER 0x0801 229#define FUNCTION_WRITE_WQBUFFER 0x0802 230#define FUNCTION_CLEAR_RQBUFFER 0x0803 231#define FUNCTION_CLEAR_WQBUFFER 0x0804 232#define FUNCTION_CLEAR_ALLQBUFFER 0x0805 233#define FUNCTION_REQUEST_RETURNCODE_3F 0x0806 234#define FUNCTION_SAY_HELLO 0x0807 235#define FUNCTION_SAY_GOODBYE 0x0808 236#define FUNCTION_FLUSH_ADAPTER_CACHE 0x0809 237/* 238************************************************************************ 239** IOCTL CONTROL CODE 240************************************************************************ 241*/ 242/* ARECA IO CONTROL CODE*/ 243#define ARCMSR_MESSAGE_READ_RQBUFFER _IOWR('F', FUNCTION_READ_RQBUFFER, struct CMD_MESSAGE_FIELD) 244#define ARCMSR_MESSAGE_WRITE_WQBUFFER _IOWR('F', FUNCTION_WRITE_WQBUFFER, struct CMD_MESSAGE_FIELD) 245#define ARCMSR_MESSAGE_CLEAR_RQBUFFER _IOWR('F', FUNCTION_CLEAR_RQBUFFER, struct CMD_MESSAGE_FIELD) 246#define ARCMSR_MESSAGE_CLEAR_WQBUFFER _IOWR('F', FUNCTION_CLEAR_WQBUFFER, struct CMD_MESSAGE_FIELD) 247#define ARCMSR_MESSAGE_CLEAR_ALLQBUFFER _IOWR('F', FUNCTION_CLEAR_ALLQBUFFER, struct CMD_MESSAGE_FIELD) 248#define ARCMSR_MESSAGE_REQUEST_RETURNCODE_3F _IOWR('F', FUNCTION_REQUEST_RETURNCODE_3F, struct CMD_MESSAGE_FIELD) 249#define ARCMSR_MESSAGE_SAY_HELLO _IOWR('F', FUNCTION_SAY_HELLO, struct CMD_MESSAGE_FIELD) 250#define ARCMSR_MESSAGE_SAY_GOODBYE _IOWR('F', FUNCTION_SAY_GOODBYE, struct CMD_MESSAGE_FIELD) 251#define ARCMSR_MESSAGE_FLUSH_ADAPTER_CACHE _IOWR('F', FUNCTION_FLUSH_ADAPTER_CACHE, struct CMD_MESSAGE_FIELD) 252 253/* ARECA IOCTL ReturnCode */ 254#define ARCMSR_MESSAGE_RETURNCODE_OK 0x00000001 255#define ARCMSR_MESSAGE_RETURNCODE_ERROR 0x00000006 256#define ARCMSR_MESSAGE_RETURNCODE_3F 0x0000003F 257#define ARCMSR_IOCTL_RETURNCODE_BUS_HANG_ON 0x00000088 258/* 259************************************************************************ 260** SPEC. for Areca HBA adapter 261************************************************************************ 262*/ 263/* signature of set and get firmware config */ 264#define ARCMSR_SIGNATURE_GET_CONFIG 0x87974060 265#define ARCMSR_SIGNATURE_SET_CONFIG 0x87974063 266/* message code of inbound message register */ 267#define ARCMSR_INBOUND_MESG0_NOP 0x00000000 268#define ARCMSR_INBOUND_MESG0_GET_CONFIG 0x00000001 269#define ARCMSR_INBOUND_MESG0_SET_CONFIG 0x00000002 270#define ARCMSR_INBOUND_MESG0_ABORT_CMD 0x00000003 271#define ARCMSR_INBOUND_MESG0_STOP_BGRB 0x00000004 272#define ARCMSR_INBOUND_MESG0_FLUSH_CACHE 0x00000005 273#define ARCMSR_INBOUND_MESG0_START_BGRB 0x00000006 274#define ARCMSR_INBOUND_MESG0_CHK331PENDING 0x00000007 275#define ARCMSR_INBOUND_MESG0_SYNC_TIMER 0x00000008 276/* doorbell interrupt generator */ 277#define ARCMSR_INBOUND_DRIVER_DATA_WRITE_OK 0x00000001 278#define ARCMSR_INBOUND_DRIVER_DATA_READ_OK 0x00000002 279#define ARCMSR_OUTBOUND_IOP331_DATA_WRITE_OK 0x00000001 280#define ARCMSR_OUTBOUND_IOP331_DATA_READ_OK 0x00000002 281/* srb areca cdb flag */ 282#define ARCMSR_SRBPOST_FLAG_SGL_BSIZE 0x80000000 283#define ARCMSR_SRBPOST_FLAG_IAM_BIOS 0x40000000 284#define ARCMSR_SRBREPLY_FLAG_IAM_BIOS 0x40000000 285#define ARCMSR_SRBREPLY_FLAG_ERROR 0x10000000 286#define ARCMSR_SRBREPLY_FLAG_ERROR_MODE0 0x10000000 287#define ARCMSR_SRBREPLY_FLAG_ERROR_MODE1 0x00000001 288/* outbound firmware ok */ 289#define ARCMSR_OUTBOUND_MESG1_FIRMWARE_OK 0x80000000 290 291#define ARCMSR_ARC1680_BUS_RESET 0x00000003 292/* 293************************************************************************ 294** SPEC. for Areca HBB adapter 295************************************************************************ 296*/ 297/* ARECA HBB COMMAND for its FIRMWARE */ 298#define ARCMSR_DRV2IOP_DOORBELL 0x00020400 /* window of "instruction flags" from driver to iop */ 299#define ARCMSR_DRV2IOP_DOORBELL_MASK 0x00020404 300#define ARCMSR_IOP2DRV_DOORBELL 0x00020408 /* window of "instruction flags" from iop to driver */ 301#define ARCMSR_IOP2DRV_DOORBELL_MASK 0x0002040C 302 303/* ARECA FLAG LANGUAGE */ 304#define ARCMSR_IOP2DRV_DATA_WRITE_OK 0x00000001 /* ioctl transfer */ 305#define ARCMSR_IOP2DRV_DATA_READ_OK 0x00000002 /* ioctl transfer */ 306#define ARCMSR_IOP2DRV_CDB_DONE 0x00000004 307#define ARCMSR_IOP2DRV_MESSAGE_CMD_DONE 0x00000008 308 309#define ARCMSR_DOORBELL_HANDLE_INT 0x0000000F 310#define ARCMSR_DOORBELL_INT_CLEAR_PATTERN 0xFF00FFF0 311#define ARCMSR_MESSAGE_INT_CLEAR_PATTERN 0xFF00FFF7 312 313#define ARCMSR_MESSAGE_GET_CONFIG 0x00010008 /* (ARCMSR_INBOUND_MESG0_GET_CONFIG<<16)|ARCMSR_DRV2IOP_MESSAGE_CMD_POSTED) */ 314#define ARCMSR_MESSAGE_SET_CONFIG 0x00020008 /* (ARCMSR_INBOUND_MESG0_SET_CONFIG<<16)|ARCMSR_DRV2IOP_MESSAGE_CMD_POSTED) */ 315#define ARCMSR_MESSAGE_ABORT_CMD 0x00030008 /* (ARCMSR_INBOUND_MESG0_ABORT_CMD<<16)|ARCMSR_DRV2IOP_MESSAGE_CMD_POSTED) */ 316#define ARCMSR_MESSAGE_STOP_BGRB 0x00040008 /* (ARCMSR_INBOUND_MESG0_STOP_BGRB<<16)|ARCMSR_DRV2IOP_MESSAGE_CMD_POSTED) */ 317#define ARCMSR_MESSAGE_FLUSH_CACHE 0x00050008 /* (ARCMSR_INBOUND_MESG0_FLUSH_CACHE<<16)|ARCMSR_DRV2IOP_MESSAGE_CMD_POSTED) */ 318#define ARCMSR_MESSAGE_START_BGRB 0x00060008 /* (ARCMSR_INBOUND_MESG0_START_BGRB<<16)|ARCMSR_DRV2IOP_MESSAGE_CMD_POSTED) */ 319#define ARCMSR_MESSAGE_START_DRIVER_MODE 0x000E0008 320#define ARCMSR_MESSAGE_SET_POST_WINDOW 0x000F0008 321#define ARCMSR_MESSAGE_ACTIVE_EOI_MODE 0x00100008 322#define ARCMSR_MESSAGE_FIRMWARE_OK 0x80000000 /* ARCMSR_OUTBOUND_MESG1_FIRMWARE_OK */ 323 324#define ARCMSR_DRV2IOP_DATA_WRITE_OK 0x00000001 /* ioctl transfer */ 325#define ARCMSR_DRV2IOP_DATA_READ_OK 0x00000002 /* ioctl transfer */ 326#define ARCMSR_DRV2IOP_CDB_POSTED 0x00000004 327#define ARCMSR_DRV2IOP_MESSAGE_CMD_POSTED 0x00000008 328#define ARCMSR_DRV2IOP_END_OF_INTERRUPT 0x00000010 /* */ 329 330/* data tunnel buffer between user space program and its firmware */ 331#define ARCMSR_MSGCODE_RWBUFFER 0x0000fa00 /* iop msgcode_rwbuffer for message command */ 332#define ARCMSR_IOCTL_WBUFFER 0x0000fe00 /* user space data to iop 128bytes */ 333#define ARCMSR_IOCTL_RBUFFER 0x0000ff00 /* iop data to user space 128bytes */ 334#define ARCMSR_HBB_BASE0_OFFSET 0x00000010 335#define ARCMSR_HBB_BASE1_OFFSET 0x00000018 336#define ARCMSR_HBB_BASE0_LEN 0x00021000 337#define ARCMSR_HBB_BASE1_LEN 0x00010000 338/* 339************************************************************************ 340** SPEC. for Areca HBC adapter 341************************************************************************ 342*/ 343#define ARCMSR_HBC_ISR_THROTTLING_LEVEL 12 344#define ARCMSR_HBC_ISR_MAX_DONE_QUEUE 20 345/* Host Interrupt Mask */ 346#define ARCMSR_HBCMU_UTILITY_A_ISR_MASK 0x00000001 /* When clear, the Utility_A interrupt routes to the host.*/ 347#define ARCMSR_HBCMU_OUTBOUND_DOORBELL_ISR_MASK 0x00000004 /* When clear, the General Outbound Doorbell interrupt routes to the host.*/ 348#define ARCMSR_HBCMU_OUTBOUND_POSTQUEUE_ISR_MASK 0x00000008 /* When clear, the Outbound Post List FIFO Not Empty interrupt routes to the host.*/ 349#define ARCMSR_HBCMU_ALL_INTMASKENABLE 0x0000000D /* disable all ISR */ 350/* Host Interrupt Status */ 351#define ARCMSR_HBCMU_UTILITY_A_ISR 0x00000001 352 /* 353 ** Set when the Utility_A Interrupt bit is set in the Outbound Doorbell Register. 354 ** It clears by writing a 1 to the Utility_A bit in the Outbound Doorbell Clear Register or through automatic clearing (if enabled). 355 */ 356#define ARCMSR_HBCMU_OUTBOUND_DOORBELL_ISR 0x00000004 357 /* 358 ** Set if Outbound Doorbell register bits 30:1 have a non-zero 359 ** value. This bit clears only when Outbound Doorbell bits 360 ** 30:1 are ALL clear. Only a write to the Outbound Doorbell 361 ** Clear register clears bits in the Outbound Doorbell register. 362 */ 363#define ARCMSR_HBCMU_OUTBOUND_POSTQUEUE_ISR 0x00000008 364 /* 365 ** Set whenever the Outbound Post List Producer/Consumer 366 ** Register (FIFO) is not empty. It clears when the Outbound 367 ** Post List FIFO is empty. 368 */ 369#define ARCMSR_HBCMU_SAS_ALL_INT 0x00000010 370 /* 371 ** This bit indicates a SAS interrupt from a source external to 372 ** the PCIe core. This bit is not maskable. 373 */ 374/* DoorBell*/ 375#define ARCMSR_HBCMU_DRV2IOP_DATA_WRITE_OK 0x00000002/**/ 376#define ARCMSR_HBCMU_DRV2IOP_DATA_READ_OK 0x00000004/**/ 377#define ARCMSR_HBCMU_DRV2IOP_MESSAGE_CMD_DONE 0x00000008/*inbound message 0 ready*/ 378#define ARCMSR_HBCMU_DRV2IOP_POSTQUEUE_THROTTLING 0x00000010/*more than 12 request completed in a time*/ 379#define ARCMSR_HBCMU_IOP2DRV_DATA_WRITE_OK 0x00000002/**/ 380#define ARCMSR_HBCMU_IOP2DRV_DATA_WRITE_DOORBELL_CLEAR 0x00000002/*outbound DATA WRITE isr door bell clear*/ 381#define ARCMSR_HBCMU_IOP2DRV_DATA_READ_OK 0x00000004/**/ 382#define ARCMSR_HBCMU_IOP2DRV_DATA_READ_DOORBELL_CLEAR 0x00000004/*outbound DATA READ isr door bell clear*/ 383#define ARCMSR_HBCMU_IOP2DRV_MESSAGE_CMD_DONE 0x00000008/*outbound message 0 ready*/ 384#define ARCMSR_HBCMU_IOP2DRV_MESSAGE_CMD_DONE_DOORBELL_CLEAR 0x00000008/*outbound message cmd isr door bell clear*/ 385#define ARCMSR_HBCMU_MESSAGE_FIRMWARE_OK 0x80000000/*ARCMSR_HBCMU_MESSAGE_FIRMWARE_OK*/ 386#define ARCMSR_HBCMU_RESET_ADAPTER 0x00000024 387#define ARCMSR_HBCMU_DiagWrite_ENABLE 0x00000080 388 389/* 390************************************************************************ 391** SPEC. for Areca HBD adapter 392************************************************************************ 393*/ 394#define ARCMSR_HBDMU_CHIP_ID 0x00004 395#define ARCMSR_HBDMU_CPU_MEMORY_CONFIGURATION 0x00008 396#define ARCMSR_HBDMU_I2_HOST_INTERRUPT_MASK 0x00034 397#define ARCMSR_HBDMU_MAIN_INTERRUPT_STATUS 0x00200 398#define ARCMSR_HBDMU_PCIE_F0_INTERRUPT_ENABLE 0x0020C 399#define ARCMSR_HBDMU_INBOUND_MESSAGE0 0x00400 400#define ARCMSR_HBDMU_INBOUND_MESSAGE1 0x00404 401#define ARCMSR_HBDMU_OUTBOUND_MESSAGE0 0x00420 402#define ARCMSR_HBDMU_OUTBOUND_MESSAGE1 0x00424 403#define ARCMSR_HBDMU_INBOUND_DOORBELL 0x00460 404#define ARCMSR_HBDMU_OUTBOUND_DOORBELL 0x00480 405#define ARCMSR_HBDMU_OUTBOUND_DOORBELL_ENABLE 0x00484 406#define ARCMSR_HBDMU_INBOUND_LIST_BASE_LOW 0x01000 407#define ARCMSR_HBDMU_INBOUND_LIST_BASE_HIGH 0x01004 408#define ARCMSR_HBDMU_INBOUND_LIST_WRITE_POINTER 0x01018 409#define ARCMSR_HBDMU_OUTBOUND_LIST_BASE_LOW 0x01060 410#define ARCMSR_HBDMU_OUTBOUND_LIST_BASE_HIGH 0x01064 411#define ARCMSR_HBDMU_OUTBOUND_LIST_COPY_POINTER 0x0106C 412#define ARCMSR_HBDMU_OUTBOUND_LIST_READ_POINTER 0x01070 413#define ARCMSR_HBDMU_OUTBOUND_INTERRUPT_CAUSE 0x01088 414#define ARCMSR_HBDMU_OUTBOUND_INTERRUPT_ENABLE 0x0108C 415 416#define ARCMSR_HBDMU_MESSAGE_WBUFFER 0x02000 417#define ARCMSR_HBDMU_MESSAGE_RBUFFER 0x02100 418#define ARCMSR_HBDMU_MESSAGE_RWBUFFER 0x02200 419 420#define ARCMSR_HBDMU_ISR_THROTTLING_LEVEL 16 421#define ARCMSR_HBDMU_ISR_MAX_DONE_QUEUE 20 422 423/* Host Interrupt Mask */ 424#define ARCMSR_HBDMU_ALL_INT_ENABLE 0x00001010 /* enable all ISR */ 425#define ARCMSR_HBDMU_ALL_INT_DISABLE 0x00000000 /* disable all ISR */ 426 427/* Host Interrupt Status */ 428#define ARCMSR_HBDMU_OUTBOUND_INT 0x00001010 429#define ARCMSR_HBDMU_OUTBOUND_DOORBELL_INT 0x00001000 430#define ARCMSR_HBDMU_OUTBOUND_POSTQUEUE_INT 0x00000010 431 432/* DoorBell*/ 433#define ARCMSR_HBDMU_DRV2IOP_DATA_IN_READY 0x00000001 434#define ARCMSR_HBDMU_DRV2IOP_DATA_OUT_READ 0x00000002 435 436#define ARCMSR_HBDMU_IOP2DRV_DATA_WRITE_OK 0x00000001 437#define ARCMSR_HBDMU_IOP2DRV_DATA_READ_OK 0x00000002 438 439/*outbound message 0 ready*/ 440#define ARCMSR_HBDMU_IOP2DRV_MESSAGE_CMD_DONE 0x02000000 441 442#define ARCMSR_HBDMU_F0_DOORBELL_CAUSE 0x02000003 443 444/*outbound message cmd isr door bell clear*/ 445#define ARCMSR_HBDMU_IOP2DRV_MESSAGE_CMD_DONE_CLEAR 0x02000000 446 447/*outbound list */ 448#define ARCMSR_HBDMU_OUTBOUND_LIST_INTERRUPT 0x00000001 449#define ARCMSR_HBDMU_OUTBOUND_LIST_INTERRUPT_CLEAR 0x00000001 450 451/*ARCMSR_HBAMU_MESSAGE_FIRMWARE_OK*/ 452#define ARCMSR_HBDMU_MESSAGE_FIRMWARE_OK 0x80000000 453/* 454********************************************************************* 455** Message Unit structure 456********************************************************************* 457*/ 458struct HBA_MessageUnit 459{ 460 u_int32_t resrved0[4]; /*0000 000F*/ 461 u_int32_t inbound_msgaddr0; /*0010 0013*/ 462 u_int32_t inbound_msgaddr1; /*0014 0017*/ 463 u_int32_t outbound_msgaddr0; /*0018 001B*/ 464 u_int32_t outbound_msgaddr1; /*001C 001F*/ 465 u_int32_t inbound_doorbell; /*0020 0023*/ 466 u_int32_t inbound_intstatus; /*0024 0027*/ 467 u_int32_t inbound_intmask; /*0028 002B*/ 468 u_int32_t outbound_doorbell; /*002C 002F*/ 469 u_int32_t outbound_intstatus; /*0030 0033*/ 470 u_int32_t outbound_intmask; /*0034 0037*/ 471 u_int32_t reserved1[2]; /*0038 003F*/ 472 u_int32_t inbound_queueport; /*0040 0043*/ 473 u_int32_t outbound_queueport; /*0044 0047*/ 474 u_int32_t reserved2[2]; /*0048 004F*/ 475 u_int32_t reserved3[492]; /*0050 07FF ......local_buffer 492*/ 476 u_int32_t reserved4[128]; /*0800 09FF 128*/ 477 u_int32_t msgcode_rwbuffer[256]; /*0a00 0DFF 256*/ 478 u_int32_t message_wbuffer[32]; /*0E00 0E7F 32*/ 479 u_int32_t reserved5[32]; /*0E80 0EFF 32*/ 480 u_int32_t message_rbuffer[32]; /*0F00 0F7F 32*/ 481 u_int32_t reserved6[32]; /*0F80 0FFF 32*/ 482}; 483/* 484********************************************************************* 485** 486********************************************************************* 487*/ 488struct HBB_DOORBELL 489{ 490 u_int8_t doorbell_reserved[ARCMSR_DRV2IOP_DOORBELL]; /*reserved */ 491 u_int32_t drv2iop_doorbell; /*offset 0x00020400:00,01,02,03: window of "instruction flags" from driver to iop */ 492 u_int32_t drv2iop_doorbell_mask; /* 04,05,06,07: doorbell mask */ 493 u_int32_t iop2drv_doorbell; /* 08,09,10,11: window of "instruction flags" from iop to driver */ 494 u_int32_t iop2drv_doorbell_mask; /* 12,13,14,15: doorbell mask */ 495}; 496/* 497********************************************************************* 498** 499********************************************************************* 500*/ 501struct HBB_RWBUFFER 502{ 503 u_int8_t message_reserved0[ARCMSR_MSGCODE_RWBUFFER]; /*reserved */ 504 u_int32_t msgcode_rwbuffer[256]; /*offset 0x0000fa00: 0, 1, 2, 3,...,1023: message code read write 1024bytes */ 505 u_int32_t message_wbuffer[32]; /*offset 0x0000fe00:1024,1025,1026,1027,...,1151: user space data to iop 128bytes */ 506 u_int32_t message_reserved1[32]; /* 1152,1153,1154,1155,...,1279: message reserved*/ 507 u_int32_t message_rbuffer[32]; /*offset 0x0000ff00:1280,1281,1282,1283,...,1407: iop data to user space 128bytes */ 508}; 509/* 510********************************************************************* 511** 512********************************************************************* 513*/ 514struct HBB_MessageUnit 515{ 516 u_int32_t post_qbuffer[ARCMSR_MAX_HBB_POSTQUEUE]; /* post queue buffer for iop */ 517 u_int32_t done_qbuffer[ARCMSR_MAX_HBB_POSTQUEUE]; /* done queue buffer for iop */ 518 int32_t postq_index; /* post queue index */ 519 int32_t doneq_index; /* done queue index */ 520 struct HBB_DOORBELL *hbb_doorbell; 521 struct HBB_RWBUFFER *hbb_rwbuffer; 522}; 523 524/* 525********************************************************************* 526** 527********************************************************************* 528*/ 529struct HBC_MessageUnit { 530 u_int32_t message_unit_status; /*0000 0003*/ 531 u_int32_t slave_error_attribute; /*0004 0007*/ 532 u_int32_t slave_error_address; /*0008 000B*/ 533 u_int32_t posted_outbound_doorbell; /*000C 000F*/ 534 u_int32_t master_error_attribute; /*0010 0013*/ 535 u_int32_t master_error_address_low; /*0014 0017*/ 536 u_int32_t master_error_address_high; /*0018 001B*/ 537 u_int32_t hcb_size; /*001C 001F size of the PCIe window used for HCB_Mode accesses*/ 538 u_int32_t inbound_doorbell; /*0020 0023*/ 539 u_int32_t diagnostic_rw_data; /*0024 0027*/ 540 u_int32_t diagnostic_rw_address_low; /*0028 002B*/ 541 u_int32_t diagnostic_rw_address_high; /*002C 002F*/ 542 u_int32_t host_int_status; /*0030 0033 host interrupt status*/ 543 u_int32_t host_int_mask; /*0034 0037 host interrupt mask*/ 544 u_int32_t dcr_data; /*0038 003B*/ 545 u_int32_t dcr_address; /*003C 003F*/ 546 u_int32_t inbound_queueport; /*0040 0043 port32 host inbound queue port*/ 547 u_int32_t outbound_queueport; /*0044 0047 port32 host outbound queue port*/ 548 u_int32_t hcb_pci_address_low; /*0048 004B*/ 549 u_int32_t hcb_pci_address_high; /*004C 004F*/ 550 u_int32_t iop_int_status; /*0050 0053*/ 551 u_int32_t iop_int_mask; /*0054 0057*/ 552 u_int32_t iop_inbound_queue_port; /*0058 005B*/ 553 u_int32_t iop_outbound_queue_port; /*005C 005F*/ 554 u_int32_t inbound_free_list_index; /*0060 0063 inbound free list producer consumer index*/ 555 u_int32_t inbound_post_list_index; /*0064 0067 inbound post list producer consumer index*/ 556 u_int32_t outbound_free_list_index; /*0068 006B outbound free list producer consumer index*/ 557 u_int32_t outbound_post_list_index; /*006C 006F outbound post list producer consumer index*/ 558 u_int32_t inbound_doorbell_clear; /*0070 0073*/ 559 u_int32_t i2o_message_unit_control; /*0074 0077*/ 560 u_int32_t last_used_message_source_address_low; /*0078 007B*/ 561 u_int32_t last_used_message_source_address_high; /*007C 007F*/ 562 u_int32_t pull_mode_data_byte_count[4]; /*0080 008F pull mode data byte count0..count7*/ 563 u_int32_t message_dest_address_index; /*0090 0093*/ 564 u_int32_t done_queue_not_empty_int_counter_timer; /*0094 0097*/ 565 u_int32_t utility_A_int_counter_timer; /*0098 009B*/ 566 u_int32_t outbound_doorbell; /*009C 009F*/ 567 u_int32_t outbound_doorbell_clear; /*00A0 00A3*/ 568 u_int32_t message_source_address_index; /*00A4 00A7 message accelerator source address consumer producer index*/ 569 u_int32_t message_done_queue_index; /*00A8 00AB message accelerator completion queue consumer producer index*/ 570 u_int32_t reserved0; /*00AC 00AF*/ 571 u_int32_t inbound_msgaddr0; /*00B0 00B3 scratchpad0*/ 572 u_int32_t inbound_msgaddr1; /*00B4 00B7 scratchpad1*/ 573 u_int32_t outbound_msgaddr0; /*00B8 00BB scratchpad2*/ 574 u_int32_t outbound_msgaddr1; /*00BC 00BF scratchpad3*/ 575 u_int32_t inbound_queueport_low; /*00C0 00C3 port64 host inbound queue port low*/ 576 u_int32_t inbound_queueport_high; /*00C4 00C7 port64 host inbound queue port high*/ 577 u_int32_t outbound_queueport_low; /*00C8 00CB port64 host outbound queue port low*/ 578 u_int32_t outbound_queueport_high; /*00CC 00CF port64 host outbound queue port high*/ 579 u_int32_t iop_inbound_queue_port_low; /*00D0 00D3*/ 580 u_int32_t iop_inbound_queue_port_high; /*00D4 00D7*/ 581 u_int32_t iop_outbound_queue_port_low; /*00D8 00DB*/ 582 u_int32_t iop_outbound_queue_port_high; /*00DC 00DF*/ 583 u_int32_t message_dest_queue_port_low; /*00E0 00E3 message accelerator destination queue port low*/ 584 u_int32_t message_dest_queue_port_high; /*00E4 00E7 message accelerator destination queue port high*/ 585 u_int32_t last_used_message_dest_address_low; /*00E8 00EB last used message accelerator destination address low*/ 586 u_int32_t last_used_message_dest_address_high; /*00EC 00EF last used message accelerator destination address high*/ 587 u_int32_t message_done_queue_base_address_low; /*00F0 00F3 message accelerator completion queue base address low*/ 588 u_int32_t message_done_queue_base_address_high; /*00F4 00F7 message accelerator completion queue base address high*/ 589 u_int32_t host_diagnostic; /*00F8 00FB*/ 590 u_int32_t write_sequence; /*00FC 00FF*/ 591 u_int32_t reserved1[34]; /*0100 0187*/ 592 u_int32_t reserved2[1950]; /*0188 1FFF*/ 593 u_int32_t message_wbuffer[32]; /*2000 207F*/ 594 u_int32_t reserved3[32]; /*2080 20FF*/ 595 u_int32_t message_rbuffer[32]; /*2100 217F*/ 596 u_int32_t reserved4[32]; /*2180 21FF*/ 597 u_int32_t msgcode_rwbuffer[256]; /*2200 23FF*/ 598}; 599/* 600********************************************************************* 601** 602********************************************************************* 603*/ 604struct InBound_SRB { 605 uint32_t addressLow; //pointer to SRB block 606 uint32_t addressHigh; 607 uint32_t length; // in DWORDs 608 uint32_t reserved0; 609}; 610 611struct OutBound_SRB { 612 uint32_t addressLow; //pointer to SRB block 613 uint32_t addressHigh; 614}; 615 616struct HBD_MessageUnit { 617 uint32_t reserved0; 618 uint32_t chip_id; //0x0004 619 uint32_t cpu_mem_config; //0x0008 620 uint32_t reserved1[10]; //0x000C 621 uint32_t i2o_host_interrupt_mask; //0x0034 622 uint32_t reserved2[114]; //0x0038 623 uint32_t host_int_status; //0x0200 624 uint32_t host_int_enable; //0x0204 625 uint32_t reserved3[1]; //0x0208 626 uint32_t pcief0_int_enable; //0x020C 627 uint32_t reserved4[124]; //0x0210 628 uint32_t inbound_msgaddr0; //0x0400 629 uint32_t inbound_msgaddr1; //0x0404 630 uint32_t reserved5[6]; //0x0408 631 uint32_t outbound_msgaddr0; //0x0420 632 uint32_t outbound_msgaddr1; //0x0424 633 uint32_t reserved6[14]; //0x0428 634 uint32_t inbound_doorbell; //0x0460 635 uint32_t reserved7[7]; //0x0464 636 uint32_t outbound_doorbell; //0x0480 637 uint32_t outbound_doorbell_enable; //0x0484 638 uint32_t reserved8[734]; //0x0488 639 uint32_t inboundlist_base_low; //0x1000 640 uint32_t inboundlist_base_high; //0x1004 641 uint32_t reserved9[4]; //0x1008 642 uint32_t inboundlist_write_pointer; //0x1018 643 uint32_t inboundlist_read_pointer; //0x101C 644 uint32_t reserved10[16]; //0x1020 645 uint32_t outboundlist_base_low; //0x1060 646 uint32_t outboundlist_base_high; //0x1064 647 uint32_t reserved11; //0x1068 648 uint32_t outboundlist_copy_pointer; //0x106C 649 uint32_t outboundlist_read_pointer; //0x1070 0x1072 650 uint32_t reserved12[5]; //0x1074 651 uint32_t outboundlist_interrupt_cause; //0x1088 652 uint32_t outboundlist_interrupt_enable; //0x108C 653 uint32_t reserved13[988]; //0x1090 654 uint32_t message_wbuffer[32]; //0x2000 655 uint32_t reserved14[32]; //0x2080 656 uint32_t message_rbuffer[32]; //0x2100 657 uint32_t reserved15[32]; //0x2180 658 uint32_t msgcode_rwbuffer[256]; //0x2200 659}; 660 661struct HBD_MessageUnit0 { 662 struct InBound_SRB post_qbuffer[ARCMSR_MAX_HBD_POSTQUEUE]; 663 struct OutBound_SRB done_qbuffer[ARCMSR_MAX_HBD_POSTQUEUE+1]; 664 uint16_t postq_index; 665 uint16_t doneq_index; 666 struct HBD_MessageUnit *phbdmu; 667}; 668 669/* 670********************************************************************* 671** 672********************************************************************* 673*/ 674struct MessageUnit_UNION 675{ 676 union { 677 struct HBA_MessageUnit hbamu; 678 struct HBB_MessageUnit hbbmu; 679 struct HBC_MessageUnit hbcmu; 680 struct HBD_MessageUnit0 hbdmu; 681 } muu; 682}; 683/* 684************************************************************* 685** structure for holding DMA address data 686************************************************************* 687*/ 688#define IS_SG64_ADDR 0x01000000 /* bit24 */ 689/* 690************************************************************************************************ 691** ARECA FIRMWARE SPEC 692************************************************************************************************ 693** Usage of IOP331 adapter 694** (All In/Out is in IOP331's view) 695** 1. Message 0 --> InitThread message and retrun code 696** 2. Doorbell is used for RS-232 emulation 697** inDoorBell : bit0 -- data in ready (DRIVER DATA WRITE OK) 698** bit1 -- data out has been read (DRIVER DATA READ OK) 699** outDooeBell: bit0 -- data out ready (IOP331 DATA WRITE OK) 700** bit1 -- data in has been read (IOP331 DATA READ OK) 701** 3. Index Memory Usage 702** offset 0xf00 : for RS232 out (request buffer) 703** offset 0xe00 : for RS232 in (scratch buffer) 704** offset 0xa00 : for inbound message code msgcode_rwbuffer (driver send to IOP331) 705** offset 0xa00 : for outbound message code msgcode_rwbuffer (IOP331 send to driver) 706** 4. RS-232 emulation 707** Currently 128 byte buffer is used 708** 1st u_int32_t : Data length (1--124) 709** Byte 4--127 : Max 124 bytes of data 710** 5. PostQ 711** All SCSI Command must be sent through postQ: 712** (inbound queue port) Request frame must be 32 bytes aligned 713** # bit27--bit31 => flag for post ccb 714** # bit0--bit26 => real address (bit27--bit31) of post arcmsr_cdb 715** bit31 : 0 : 256 bytes frame 716** 1 : 512 bytes frame 717** bit30 : 0 : normal request 718** 1 : BIOS request 719** bit29 : reserved 720** bit28 : reserved 721** bit27 : reserved 722** ------------------------------------------------------------------------------- 723** (outbount queue port) Request reply 724** # bit27--bit31 => flag for reply 725** # bit0--bit26 => real address (bit27--bit31) of reply arcmsr_cdb 726** bit31 : must be 0 (for this type of reply) 727** bit30 : reserved for BIOS handshake 728** bit29 : reserved 729** bit28 : 0 : no error, ignore AdapStatus/DevStatus/SenseData 730** 1 : Error, error code in AdapStatus/DevStatus/SenseData 731** bit27 : reserved 732** 6. BIOS request 733** All BIOS request is the same with request from PostQ 734** Except : 735** Request frame is sent from configuration space 736** offset: 0x78 : Request Frame (bit30 == 1) 737** offset: 0x18 : writeonly to generate IRQ to IOP331 738** Completion of request: 739** (bit30 == 0, bit28==err flag) 740** 7. Definition of SGL entry (structure) 741** 8. Message1 Out - Diag Status Code (????) 742** 9. Message0 message code : 743** 0x00 : NOP 744** 0x01 : Get Config ->offset 0xa00 :for outbound message code msgcode_rwbuffer (IOP331 send to driver) 745** Signature 0x87974060(4) 746** Request len 0x00000200(4) 747** numbers of queue 0x00000100(4) 748** SDRAM Size 0x00000100(4)-->256 MB 749** IDE Channels 0x00000008(4) 750** vendor 40 bytes char 751** model 8 bytes char 752** FirmVer 16 bytes char 753** Device Map 16 bytes char 754** 755** FirmwareVersion DWORD <== Added for checking of new firmware capability 756** 0x02 : Set Config ->offset 0xa00 : for inbound message code msgcode_rwbuffer (driver send to IOP331) 757** Signature 0x87974063(4) 758** UPPER32 of Request Frame (4)-->Driver Only 759** 0x03 : Reset (Abort all queued Command) 760** 0x04 : Stop Background Activity 761** 0x05 : Flush Cache 762** 0x06 : Start Background Activity (re-start if background is halted) 763** 0x07 : Check If Host Command Pending (Novell May Need This Function) 764** 0x08 : Set controller time ->offset 0xa00 : for inbound message code msgcode_rwbuffer (driver to IOP331) 765** byte 0 : 0xaa <-- signature 766** byte 1 : 0x55 <-- signature 767** byte 2 : year (04) 768** byte 3 : month (1..12) 769** byte 4 : date (1..31) 770** byte 5 : hour (0..23) 771** byte 6 : minute (0..59) 772** byte 7 : second (0..59) 773** ********************************************************************************* 774** Porting Of LSI2108/2116 Based PCIE SAS/6G host raid adapter 775** ==> Difference from IOP348 776** <1> Message Register 0,1 (the same usage) Init Thread message and retrun code 777** Inbound Message 0 (inbound_msgaddr0) : at offset 0xB0 (Scratchpad0) for inbound message code msgcode_rwbuffer (driver send to IOP) 778** Inbound Message 1 (inbound_msgaddr1) : at offset 0xB4 (Scratchpad1) Out.... Diag Status Code 779** Outbound Message 0 (outbound_msgaddr0): at offset 0xB8 (Scratchpad3) Out.... Diag Status Code 780** Outbound Message 1 (outbound_msgaddr1): at offset 0xBC (Scratchpad2) for outbound message code msgcode_rwbuffer (IOP send to driver) 781** <A> use doorbell to generate interrupt 782** 783** inbound doorbell: bit3 -- inbound message 0 ready (driver to iop) 784** outbound doorbell: bit3 -- outbound message 0 ready (iop to driver) 785** 786** a. Message1: Out - Diag Status Code (????) 787** 788** b. Message0: message code 789** 0x00 : NOP 790** 0x01 : Get Config ->offset 0xB8 :for outbound message code msgcode_rwbuffer (IOP send to driver) 791** Signature 0x87974060(4) 792** Request len 0x00000200(4) 793** numbers of queue 0x00000100(4) 794** SDRAM Size 0x00000100(4)-->256 MB 795** IDE Channels 0x00000008(4) 796** vendor 40 bytes char 797** model 8 bytes char 798** FirmVer 16 bytes char 799** Device Map 16 bytes char 800** cfgVersion ULONG <== Added for checking of new firmware capability 801** 0x02 : Set Config ->offset 0xB0 :for inbound message code msgcode_rwbuffer (driver send to IOP) 802** Signature 0x87974063(4) 803** UPPER32 of Request Frame (4)-->Driver Only 804** 0x03 : Reset (Abort all queued Command) 805** 0x04 : Stop Background Activity 806** 0x05 : Flush Cache 807** 0x06 : Start Background Activity (re-start if background is halted) 808** 0x07 : Check If Host Command Pending (Novell May Need This Function) 809** 0x08 : Set controller time ->offset 0xB0 : for inbound message code msgcode_rwbuffer (driver to IOP) 810** byte 0 : 0xaa <-- signature 811** byte 1 : 0x55 <-- signature 812** byte 2 : year (04) 813** byte 3 : month (1..12) 814** byte 4 : date (1..31) 815** byte 5 : hour (0..23) 816** byte 6 : minute (0..59) 817** byte 7 : second (0..59) 818** 819** <2> Doorbell Register is used for RS-232 emulation 820** <A> different clear register 821** <B> different bit0 definition (bit0 is reserved) 822** 823** inbound doorbell : at offset 0x20 824** inbound doorbell clear : at offset 0x70 825** 826** inbound doorbell : bit0 -- reserved 827** bit1 -- data in ready (DRIVER DATA WRITE OK) 828** bit2 -- data out has been read (DRIVER DATA READ OK) 829** bit3 -- inbound message 0 ready 830** bit4 -- more than 12 request completed in a time 831** 832** outbound doorbell : at offset 0x9C 833** outbound doorbell clear : at offset 0xA0 834** 835** outbound doorbell : bit0 -- reserved 836** bit1 -- data out ready (IOP DATA WRITE OK) 837** bit2 -- data in has been read (IOP DATA READ OK) 838** bit3 -- outbound message 0 ready 839** 840** <3> Index Memory Usage (Buffer Area) 841** COMPORT_IN at 0x2000: message_wbuffer -- 128 bytes (to be sent to ROC) : for RS232 in (scratch buffer) 842** COMPORT_OUT at 0x2100: message_rbuffer -- 128 bytes (to be sent to host): for RS232 out (request buffer) 843** BIOS_CFG_AREA at 0x2200: msgcode_rwbuffer -- 1024 bytes for outbound message code msgcode_rwbuffer (IOP send to driver) 844** BIOS_CFG_AREA at 0x2200: msgcode_rwbuffer -- 1024 bytes for inbound message code msgcode_rwbuffer (driver send to IOP) 845** 846** <4> PostQ (Command Post Address) 847** All SCSI Command must be sent through postQ: 848** inbound queue port32 at offset 0x40 , 0x41, 0x42, 0x43 849** inbound queue port64 at offset 0xC0 (lower)/0xC4 (upper) 850** outbound queue port32 at offset 0x44 851** outbound queue port64 at offset 0xC8 (lower)/0xCC (upper) 852** <A> For 32bit queue, access low part is enough to send/receive request 853** i.e. write 0x40/0xC0, ROC will get the request with high part == 0, the 854** same for outbound queue port 855** <B> For 64bit queue, if 64bit instruction is supported, use 64bit instruction 856** to post inbound request in a single instruction, and use 64bit instruction 857** to retrieve outbound request in a single instruction. 858** If in 32bit environment, when sending inbound queue, write high part first 859** then write low part. For receiving outbound request, read high part first 860** then low part, to check queue empty, ONLY check high part to be 0xFFFFFFFF. 861** If high part is 0xFFFFFFFF, DO NOT read low part, this may corrupt the 862** consistency of the FIFO. Another way to check empty is to check status flag 863** at 0x30 bit3. 864** <C> Post Address IS NOT shifted (must be 16 bytes aligned) 865** For BIOS, 16bytes aligned is OK 866** For Driver, 32bytes alignment is recommended. 867** POST Command bit0 to bit3 is defined differently 868** ---------------------------- 869** bit0:1 for PULL mode (must be 1) 870** ---------------------------- 871** bit3/2/1: for arcmsr cdb size (arccdbsize) 872** 000: <= 0x0080 (128) 873** 001: <= 0x0100 (256) 874** 010: <= 0x0180 (384) 875** 011: <= 0x0200 (512) 876** 100: <= 0x0280 (640) 877** 101: <= 0x0300 (768) 878** 110: <= 0x0300 (reserved) 879** 111: <= 0x0300 (reserved) 880** ----------------------------- 881** if len > 0x300 the len always set as 0x300 882** ----------------------------- 883** post addr = addr | ((len-1) >> 6) | 1 884** ----------------------------- 885** page length in command buffer still required, 886** 887** if page length > 3, 888** firmware will assume more request data need to be retrieved 889** 890** <D> Outbound Posting 891** bit0:0 , no error, 1 with error, refer to status buffer 892** bit1:0 , reserved (will be 0) 893** bit2:0 , reserved (will be 0) 894** bit3:0 , reserved (will be 0) 895** bit63-4: Completed command address 896** 897** <E> BIOS support, no special support is required. 898** LSI2108 support I/O register 899** All driver functionality is supported through I/O address 900** 901************************************************************************************************ 902*/ 903/* 904********************************** 905** 906********************************** 907*/ 908/* size 8 bytes */ 909/* 32bit Scatter-Gather list */ 910struct SG32ENTRY { /* length bit 24 == 0 */ 911 u_int32_t length; /* high 8 bit == flag,low 24 bit == length */ 912 u_int32_t address; 913}; 914/* size 12 bytes */ 915/* 64bit Scatter-Gather list */ 916struct SG64ENTRY { /* length bit 24 == 1 */ 917 u_int32_t length; /* high 8 bit == flag,low 24 bit == length */ 918 u_int32_t address; 919 u_int32_t addresshigh; 920}; 921struct SGENTRY_UNION { 922 union { 923 struct SG32ENTRY sg32entry; /* 30h Scatter gather address */ 924 struct SG64ENTRY sg64entry; /* 30h */ 925 }u; 926}; 927/* 928********************************** 929** 930********************************** 931*/ 932struct QBUFFER { 933 u_int32_t data_len; 934 u_int8_t data[124]; 935}; 936/* 937********************************** 938*/ 939typedef struct PHYS_ADDR64 { 940 u_int32_t phyadd_low; 941 u_int32_t phyadd_high; 942}PHYSADDR64; 943/* 944************************************************************************************************ 945** FIRMWARE INFO 946************************************************************************************************ 947*/ 948#define ARCMSR_FW_MODEL_OFFSET 15 949#define ARCMSR_FW_VERS_OFFSET 17 950#define ARCMSR_FW_DEVMAP_OFFSET 21 951#define ARCMSR_FW_CFGVER_OFFSET 25 952 953struct FIRMWARE_INFO { 954 u_int32_t signature; /*0,00-03*/ 955 u_int32_t request_len; /*1,04-07*/ 956 u_int32_t numbers_queue; /*2,08-11*/ 957 u_int32_t sdram_size; /*3,12-15*/ 958 u_int32_t ide_channels; /*4,16-19*/ 959 char vendor[40]; /*5,20-59*/ 960 char model[8]; /*15,60-67*/ 961 char firmware_ver[16]; /*17,68-83*/ 962 char device_map[16]; /*21,84-99*/ 963 u_int32_t cfgVersion; /*25,100-103 Added for checking of new firmware capability*/ 964 char cfgSerial[16]; /*26,104-119*/ 965 u_int32_t cfgPicStatus; /*30,120-123*/ 966}; 967/* (A) For cfgVersion in FIRMWARE_INFO 968** if low BYTE (byte#0) >= 3 (version 3) 969** then byte#1 report the capability of the firmware can xfer in a single request 970** 971** byte#1 972** 0 256K 973** 1 512K 974** 2 1M 975** 3 2M 976** 4 4M 977** 5 8M 978** 6 16M 979** (B) Byte offset 7 (Reserved1) of CDB is changed to msgPages 980** Driver support new xfer method need to set this field to indicate 981** large CDB block in 0x100 unit (we use 0x100 byte as one page) 982** e.g. If the length of CDB including MSG header and SGL is 0x1508 983** driver need to set the msgPages to 0x16 984** (C) REQ_LEN_512BYTE must be used also to indicate SRB length 985** e.g. CDB len msgPages REQ_LEN_512BYTE flag 986** <= 0x100 1 0 987** <= 0x200 2 1 988** <= 0x300 3 1 989** <= 0x400 4 1 990** . 991** . 992*/ 993 994/* 995************************************************************************************************ 996** size 0x1F8 (504) 997************************************************************************************************ 998*/ 999struct ARCMSR_CDB { 1000 u_int8_t Bus; /* 00h should be 0 */ 1001 u_int8_t TargetID; /* 01h should be 0--15 */ 1002 u_int8_t LUN; /* 02h should be 0--7 */ 1003 u_int8_t Function; /* 03h should be 1 */ 1004 1005 u_int8_t CdbLength; /* 04h not used now */ 1006 u_int8_t sgcount; /* 05h */ 1007 u_int8_t Flags; /* 06h */ 1008 u_int8_t msgPages; /* 07h */ 1009 1010 u_int32_t Context; /* 08h Address of this request */ 1011 u_int32_t DataLength; /* 0ch not used now */ 1012 1013 u_int8_t Cdb[16]; /* 10h SCSI CDB */ 1014 /* 1015 ******************************************************** 1016 ** Device Status : the same from SCSI bus if error occur 1017 ** SCSI bus status codes. 1018 ******************************************************** 1019 */ 1020 u_int8_t DeviceStatus; /* 20h if error */ 1021 1022 u_int8_t SenseData[15]; /* 21h output */ 1023 1024 union { 1025 struct SG32ENTRY sg32entry[ARCMSR_MAX_SG_ENTRIES]; /* 30h Scatter gather address */ 1026 struct SG64ENTRY sg64entry[ARCMSR_MAX_SG_ENTRIES]; /* 30h */ 1027 } u; 1028}; 1029/* CDB flag */ 1030#define ARCMSR_CDB_FLAG_SGL_BSIZE 0x01 /* bit 0: 0(256) / 1(512) bytes */ 1031#define ARCMSR_CDB_FLAG_BIOS 0x02 /* bit 1: 0(from driver) / 1(from BIOS) */ 1032#define ARCMSR_CDB_FLAG_WRITE 0x04 /* bit 2: 0(Data in) / 1(Data out) */ 1033#define ARCMSR_CDB_FLAG_SIMPLEQ 0x00 /* bit 4/3 ,00 : simple Q,01 : head of Q,10 : ordered Q */ 1034#define ARCMSR_CDB_FLAG_HEADQ 0x08 1035#define ARCMSR_CDB_FLAG_ORDEREDQ 0x10 1036/* scsi status */ 1037#define SCSISTAT_GOOD 0x00 1038#define SCSISTAT_CHECK_CONDITION 0x02 1039#define SCSISTAT_CONDITION_MET 0x04 1040#define SCSISTAT_BUSY 0x08 1041#define SCSISTAT_INTERMEDIATE 0x10 1042#define SCSISTAT_INTERMEDIATE_COND_MET 0x14 1043#define SCSISTAT_RESERVATION_CONFLICT 0x18 1044#define SCSISTAT_COMMAND_TERMINATED 0x22 1045#define SCSISTAT_QUEUE_FULL 0x28 1046/* DeviceStatus */ 1047#define ARCMSR_DEV_SELECT_TIMEOUT 0xF0 1048#define ARCMSR_DEV_ABORTED 0xF1 1049#define ARCMSR_DEV_INIT_FAIL 0xF2 1050/* 1051********************************************************************* 1052** Command Control Block (SrbExtension) 1053** SRB must be not cross page boundary,and the order from offset 0 1054** structure describing an ATA disk request 1055** this SRB length must be 32 bytes boundary 1056********************************************************************* 1057*/ 1058struct CommandControlBlock { 1059 struct ARCMSR_CDB arcmsr_cdb; /* 0 -503 (size of CDB=504): arcmsr messenger scsi command descriptor size 504 bytes */ 1060 u_int32_t cdb_phyaddr_low; /* 504-507 */ 1061 u_int32_t arc_cdb_size; /* 508-511 */ 1062 /* ======================512+32 bytes============================ */ 1063 union ccb *pccb; /* 512-515 516-519 pointer of freebsd scsi command */ 1064 struct AdapterControlBlock *acb; /* 520-523 524-527 */ 1065 bus_dmamap_t dm_segs_dmamap; /* 528-531 532-535 */ 1066 u_int16_t srb_flags; /* 536-537 */ 1067 u_int16_t srb_state; /* 538-539 */ 1068 u_int32_t cdb_phyaddr_high; /* 540-543 */ 1069 struct callout ccb_callout; 1070 /* ========================================================== */ 1071}; 1072/* srb_flags */ 1073#define SRB_FLAG_READ 0x0000 1074#define SRB_FLAG_WRITE 0x0001 1075#define SRB_FLAG_ERROR 0x0002 1076#define SRB_FLAG_FLUSHCACHE 0x0004 1077#define SRB_FLAG_MASTER_ABORTED 0x0008 1078#define SRB_FLAG_DMAVALID 0x0010 1079#define SRB_FLAG_DMACONSISTENT 0x0020 1080#define SRB_FLAG_DMAWRITE 0x0040 1081#define SRB_FLAG_PKTBIND 0x0080 1082#define SRB_FLAG_TIMER_START 0x0080 1083/* srb_state */ 1084#define ARCMSR_SRB_DONE 0x0000 1085#define ARCMSR_SRB_UNBUILD 0x0000 1086#define ARCMSR_SRB_TIMEOUT 0x1111 1087#define ARCMSR_SRB_RETRY 0x2222 1088#define ARCMSR_SRB_START 0x55AA 1089#define ARCMSR_SRB_PENDING 0xAA55 1090#define ARCMSR_SRB_RESET 0xA5A5 1091#define ARCMSR_SRB_ABORTED 0x5A5A 1092#define ARCMSR_SRB_ILLEGAL 0xFFFF 1093 1094#define SRB_SIZE ((sizeof(struct CommandControlBlock)+0x1f) & 0xffe0) 1095#define ARCMSR_SRBS_POOL_SIZE (SRB_SIZE * ARCMSR_MAX_FREESRB_NUM) 1096 1097/* 1098********************************************************************* 1099** Adapter Control Block 1100********************************************************************* 1101*/ 1102#define ACB_ADAPTER_TYPE_A 0x00000001 /* hba I IOP */ 1103#define ACB_ADAPTER_TYPE_B 0x00000002 /* hbb M IOP */ 1104#define ACB_ADAPTER_TYPE_C 0x00000004 /* hbc L IOP */ 1105#define ACB_ADAPTER_TYPE_D 0x00000008 /* hbd M IOP */ 1106 1107struct AdapterControlBlock { 1108 u_int32_t adapter_type; /* adapter A,B..... */ 1109 1110 bus_space_tag_t btag[2]; 1111 bus_space_handle_t bhandle[2]; 1112 bus_dma_tag_t parent_dmat; 1113 bus_dma_tag_t dm_segs_dmat; /* dmat for buffer I/O */ 1114 bus_dma_tag_t srb_dmat; /* dmat for freesrb */ 1115 bus_dmamap_t srb_dmamap; 1116 device_t pci_dev; 1117#if __FreeBSD_version < 503000 1118 dev_t ioctl_dev; 1119#else 1120 struct cdev *ioctl_dev; 1121#endif 1122 int pci_unit; 1123 1124 struct resource *sys_res_arcmsr[2]; 1125 struct resource *irqres; 1126 void *ih; /* interrupt handle */ 1127 1128 /* Hooks into the CAM XPT */ 1129 struct cam_sim *psim; 1130 struct cam_path *ppath; 1131 u_int8_t *uncacheptr; 1132 unsigned long vir2phy_offset; 1133 union { 1134 unsigned long phyaddr; 1135 struct { 1136 u_int32_t phyadd_low; 1137 u_int32_t phyadd_high; 1138 }B; 1139 } srb_phyaddr; 1140// unsigned long srb_phyaddr; 1141 /* Offset is used in making arc cdb physical to virtual calculations */ 1142 u_int32_t outbound_int_enable; 1143 1144 struct MessageUnit_UNION *pmu; /* message unit ATU inbound base address0 */ 1145 1146 u_int8_t adapter_index; /* */ 1147 u_int8_t irq; 1148 u_int16_t acb_flags; /* */ 1149 1150 struct CommandControlBlock *psrb_pool[ARCMSR_MAX_FREESRB_NUM]; /* serial srb pointer array */ 1151 struct CommandControlBlock *srbworkingQ[ARCMSR_MAX_FREESRB_NUM]; /* working srb pointer array */ 1152 int32_t workingsrb_doneindex; /* done srb array index */ 1153 int32_t workingsrb_startindex; /* start srb array index */ 1154 int32_t srboutstandingcount; 1155 1156 u_int8_t rqbuffer[ARCMSR_MAX_QBUFFER]; /* data collection buffer for read from 80331 */ 1157 u_int32_t rqbuf_firstindex; /* first of read buffer */ 1158 u_int32_t rqbuf_lastindex; /* last of read buffer */ 1159 1160 u_int8_t wqbuffer[ARCMSR_MAX_QBUFFER]; /* data collection buffer for write to 80331 */ 1161 u_int32_t wqbuf_firstindex; /* first of write buffer */ 1162 u_int32_t wqbuf_lastindex; /* last of write buffer */ 1163 1164 arcmsr_lock_t isr_lock; 1165 arcmsr_lock_t srb_lock; 1166 arcmsr_lock_t postDone_lock; 1167 arcmsr_lock_t qbuffer_lock; 1168 1169 u_int8_t devstate[ARCMSR_MAX_TARGETID][ARCMSR_MAX_TARGETLUN]; /* id0 ..... id15,lun0...lun7 */ 1170 u_int32_t num_resets; 1171 u_int32_t num_aborts; 1172 u_int32_t firm_request_len; /*1,04-07*/ 1173 u_int32_t firm_numbers_queue; /*2,08-11*/ 1174 u_int32_t firm_sdram_size; /*3,12-15*/ 1175 u_int32_t firm_ide_channels; /*4,16-19*/ 1176 u_int32_t firm_cfg_version; 1177 char firm_model[12]; /*15,60-67*/ 1178 char firm_version[20]; /*17,68-83*/ 1179 char device_map[20]; /*21,84-99 */ 1180 struct callout devmap_callout; 1181 u_int32_t pktRequestCount; 1182 u_int32_t pktReturnCount; 1183 u_int32_t vendor_device_id; 1184 u_int32_t adapter_bus_speed; 1185 u_int32_t maxOutstanding; 1186};/* HW_DEVICE_EXTENSION */ 1187/* acb_flags */ 1188#define ACB_F_SCSISTOPADAPTER 0x0001 1189#define ACB_F_MSG_STOP_BGRB 0x0002 /* stop RAID background rebuild */ 1190#define ACB_F_MSG_START_BGRB 0x0004 /* stop RAID background rebuild */ 1191#define ACB_F_IOPDATA_OVERFLOW 0x0008 /* iop ioctl data rqbuffer overflow */ 1192#define ACB_F_MESSAGE_WQBUFFER_CLEARED 0x0010 /* ioctl clear wqbuffer */ 1193#define ACB_F_MESSAGE_RQBUFFER_CLEARED 0x0020 /* ioctl clear rqbuffer */ 1194#define ACB_F_MESSAGE_WQBUFFER_READ 0x0040 1195#define ACB_F_BUS_RESET 0x0080 1196#define ACB_F_IOP_INITED 0x0100 /* iop init */ 1197#define ACB_F_MAPFREESRB_FAILD 0x0200 /* arcmsr_map_freesrb faild */ 1198#define ACB_F_CAM_DEV_QFRZN 0x0400 1199#define ACB_F_BUS_HANG_ON 0x0800 /* need hardware reset bus */ 1200#define ACB_F_SRB_FUNCTION_POWER 0x1000 1201/* devstate */ 1202#define ARECA_RAID_GONE 0x55 1203#define ARECA_RAID_GOOD 0xaa 1204/* adapter_bus_speed */ 1205#define ACB_BUS_SPEED_3G 0 1206#define ACB_BUS_SPEED_6G 1 1207#define ACB_BUS_SPEED_12G 2 1208/* 1209************************************************************* 1210************************************************************* 1211*/ 1212struct SENSE_DATA { 1213 u_int8_t ErrorCode:7; 1214 u_int8_t Valid:1; 1215 u_int8_t SegmentNumber; 1216 u_int8_t SenseKey:4; 1217 u_int8_t Reserved:1; 1218 u_int8_t IncorrectLength:1; 1219 u_int8_t EndOfMedia:1; 1220 u_int8_t FileMark:1; 1221 u_int8_t Information[4]; 1222 u_int8_t AdditionalSenseLength; 1223 u_int8_t CommandSpecificInformation[4]; 1224 u_int8_t AdditionalSenseCode; 1225 u_int8_t AdditionalSenseCodeQualifier; 1226 u_int8_t FieldReplaceableUnitCode; 1227 u_int8_t SenseKeySpecific[3]; 1228}; 1229/* 1230********************************** 1231** Peripheral Device Type definitions 1232********************************** 1233*/ 1234#define SCSI_DASD 0x00 /* Direct-access Device */ 1235#define SCSI_SEQACESS 0x01 /* Sequential-access device */ 1236#define SCSI_PRINTER 0x02 /* Printer device */ 1237#define SCSI_PROCESSOR 0x03 /* Processor device */ 1238#define SCSI_WRITEONCE 0x04 /* Write-once device */ 1239#define SCSI_CDROM 0x05 /* CD-ROM device */ 1240#define SCSI_SCANNER 0x06 /* Scanner device */ 1241#define SCSI_OPTICAL 0x07 /* Optical memory device */ 1242#define SCSI_MEDCHGR 0x08 /* Medium changer device */ 1243#define SCSI_COMM 0x09 /* Communications device */ 1244#define SCSI_NODEV 0x1F /* Unknown or no device type */ 1245/* 1246************************************************************************************************************ 1247** @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ 1248** 80331 PCI-to-PCI Bridge 1249** PCI Configuration Space 1250** 1251** @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ 1252** Programming Interface 1253** ======================== 1254** Configuration Register Address Space Groupings and Ranges 1255** ============================================================= 1256** Register Group Configuration Offset 1257** ------------------------------------------------------------- 1258** Standard PCI Configuration 00-3Fh 1259** ------------------------------------------------------------- 1260** Device Specific Registers 40-A7h 1261** ------------------------------------------------------------- 1262** Reserved A8-CBh 1263** ------------------------------------------------------------- 1264** Enhanced Capability List CC-FFh 1265** ========================================================================================================== 1266** Standard PCI [Type 1] Configuration Space Address Map 1267** ********************************************************************************************************** 1268** | Byte 3 | Byte 2 | Byte 1 | Byte 0 | Configu-ration Byte Offset 1269** ---------------------------------------------------------------------------------------------------------- 1270** | Device ID | Vendor ID | 00h 1271** ---------------------------------------------------------------------------------------------------------- 1272** | Primary Status | Primary Command | 04h 1273** ---------------------------------------------------------------------------------------------------------- 1274** | Class Code | RevID | 08h 1275** ---------------------------------------------------------------------------------------------------------- 1276** | reserved | Header Type | Primary MLT | Primary CLS | 0Ch 1277** ---------------------------------------------------------------------------------------------------------- 1278** | Reserved | 10h 1279** ---------------------------------------------------------------------------------------------------------- 1280** | Reserved | 14h 1281** ---------------------------------------------------------------------------------------------------------- 1282** | Secondary MLT | Subordinate Bus Number | Secondary Bus Number | Primary Bus Number | 18h 1283** ---------------------------------------------------------------------------------------------------------- 1284** | Secondary Status | I/O Limit | I/O Base | 1Ch 1285** ---------------------------------------------------------------------------------------------------------- 1286** | Non-prefetchable Memory Limit Address | Non-prefetchable Memory Base Address | 20h 1287** ---------------------------------------------------------------------------------------------------------- 1288** | Prefetchable Memory Limit Address | Prefetchable Memory Base Address | 24h 1289** ---------------------------------------------------------------------------------------------------------- 1290** | Prefetchable Memory Base Address Upper 32 Bits | 28h 1291** ---------------------------------------------------------------------------------------------------------- 1292** | Prefetchable Memory Limit Address Upper 32 Bits | 2Ch 1293** ---------------------------------------------------------------------------------------------------------- 1294** | I/O Limit Upper 16 Bits | I/O Base Upper 16 | 30h 1295** ---------------------------------------------------------------------------------------------------------- 1296** | Reserved | Capabilities Pointer | 34h 1297** ---------------------------------------------------------------------------------------------------------- 1298** | Reserved | 38h 1299** ---------------------------------------------------------------------------------------------------------- 1300** | Bridge Control | Primary Interrupt Pin | Primary Interrupt Line | 3Ch 1301**============================================================================================================= 1302*/ 1303/* 1304**============================================================================================================= 1305** 0x03-0x00 : 1306** Bit Default Description 1307**31:16 0335h Device ID (DID): Indicates the unique device ID that is assigned to bridge by the PCI SIG. 1308** ID is unique per product speed as indicated. 1309**15:00 8086h Vendor ID (VID): 16-bit field which indicates that Intel is the vendor. 1310**============================================================================================================= 1311*/ 1312#define ARCMSR_PCI2PCI_VENDORID_REG 0x00 /*word*/ 1313#define ARCMSR_PCI2PCI_DEVICEID_REG 0x02 /*word*/ 1314/* 1315**============================================================================== 1316** 0x05-0x04 : command register 1317** Bit Default Description 1318**15:11 00h Reserved 1319** 10 0 Interrupt Disable: Disables/Enables the generation of Interrupts on the primary bus. 1320** The bridge does not support interrupts. 1321** 09 0 FB2B Enable: Enables/Disables the generation of fast back to back 1322** transactions on the primary bus. 1323** The bridge does not generate fast back to back 1324** transactions on the primary bus. 1325** 08 0 SERR# Enable (SEE): Enables primary bus SERR# assertions. 1326** 0=The bridge does not assert P_SERR#. 1327** 1=The bridge may assert P_SERR#, subject to other programmable criteria. 1328** 07 0 Wait Cycle Control (WCC): Always returns 0bzero indicating 1329** that bridge does not perform address or data stepping, 1330** 06 0 Parity Error Response (PER): Controls bridge response to a detected primary bus parity error. 1331** 0=When a data parity error is detected bridge does not assert S_PERR#. 1332** Also bridge does not assert P_SERR# in response to 1333** a detected address or attribute parity error. 1334** 1=When a data parity error is detected bridge asserts S_PERR#. 1335** The bridge also asserts P_SERR# 1336** (when enabled globally via bit(8) of this register) 1337** in response to a detected address or attribute parity error. 1338** 05 0 VGA Palette Snoop Enable (VGA_PSE): Controls bridge response to VGA-compatible palette write transactions. 1339** VGA palette write transactions are I/O transactions 1340** whose address bits are: P_AD[9:0] equal to 3C6h, 3C8h or 3C9h 1341** P_AD[15:10] are not decoded (i.e. aliases are claimed), 1342** or are fully decoding 1343** (i.e., must be all 0's depending upon the VGA 1344** aliasing bit in the Bridge Control Register, offset 3Eh. 1345** P_AD[31:16] equal to 0000h 1346** 0=The bridge ignores VGA palette write transactions, 1347** unless decoded by the standard I/O address range window. 1348** 1=The bridge responds to VGA palette write transactions 1349** with medium DEVSEL# timing and forwards them to the secondary bus. 1350** 04 0 Memory Write and Invalidate Enable (MWIE): The bridge does not promote MW transactions to MWI transactions. 1351** MWI transactions targeting resources on the opposite side of the bridge, 1352** however, are forwarded as MWI transactions. 1353** 03 0 Special Cycle Enable (SCE): The bridge ignores special cycle transactions. 1354** This bit is read only and always returns 0 when read 1355** 02 0 Bus Master Enable (BME): Enables bridge to initiate memory and I/O transactions on the primary interface. 1356** Initiation of configuration transactions is not affected by the state of this bit. 1357** 0=The bridge does not initiate memory or I/O transactions on the primary interface. 1358** 1=The bridge is enabled to function as an initiator on the primary interface. 1359** 01 0 Memory Space Enable (MSE): Controls target response to memory transactions on the primary interface. 1360** 0=The bridge target response to memory transactions on the primary interface is disabled. 1361** 1=The bridge target response to memory transactions on the primary interface is enabled. 1362** 00 0 I/O Space Enable (IOSE): Controls target response to I/O transactions on the primary interface. 1363** 0=The bridge target response to I/O transactions on the primary interface is disabled. 1364** 1=The bridge target response to I/O transactions on the primary interface is enabled. 1365**============================================================================== 1366*/ 1367#define ARCMSR_PCI2PCI_PRIMARY_COMMAND_REG 0x04 /*word*/ 1368#define PCI_DISABLE_INTERRUPT 0x0400 1369/* 1370**============================================================================== 1371** 0x07-0x06 : status register 1372** Bit Default Description 1373** 15 0 Detected Parity Error: The bridge sets this bit to a 1b whenever it detects an address, 1374** attribute or data parity error. 1375** This bit is set regardless of the state of the PER bit in the command register. 1376** 14 0 Signaled System Error: The bridge sets this bit to a 1b whenever it asserts SERR# on the primary bus. 1377** 13 0 Received Master Abort: The bridge sets this bit to a 1b when, 1378** acting as the initiator on the primary bus, 1379** its transaction (with the exception of special cycles) 1380** has been terminated with a Master Abort. 1381** 12 0 Received Target Abort: The bridge sets this bit to a 1b when, 1382** acting as the initiator on the primary bus, 1383** its transaction has been terminated with a Target Abort. 1384** 11 0 Signaled Target Abort: The bridge sets this bit to a 1b when it, 1385** as the target of a transaction, terminates it with a Target Abort. 1386** In PCI-X mode this bit is also set when it forwards a SCM with a target abort error code. 1387** 10:09 01 DEVSEL# Timing: Indicates slowest response to a non-configuration command on the primary interface. 1388** Returns ��01b�� when read, indicating that bridge responds no slower than with medium timing. 1389** 08 0 Master Data Parity Error: The bridge sets this bit to a 1b when all of the following conditions are true: 1390** The bridge is the current master on the primary bus 1391** S_PERR# is detected asserted or is asserted by bridge 1392** The Parity Error Response bit is set in the Command register 1393** 07 1 Fast Back to Back Capable: Returns a 1b when read indicating that bridge 1394** is able to respond to fast back to back transactions on its primary interface. 1395** 06 0 Reserved 1396** 05 1 66 MHz Capable Indication: Returns a 1b when read indicating that bridge primary interface is 66 MHz capable. 1397** 1 = 1398** 04 1 Capabilities List Enable: Returns 1b when read indicating that bridge supports PCI standard enhanced capabilities. 1399** Offset 34h (Capability Pointer register) 1400** provides the offset for the first entry 1401** in the linked list of enhanced capabilities. 1402** 03 0 Interrupt Status: Reflects the state of the interrupt in the device/function. 1403** The bridge does not support interrupts. 1404** 02:00 000 Reserved 1405**============================================================================== 1406*/ 1407#define ARCMSR_PCI2PCI_PRIMARY_STATUS_REG 0x06 /*word: 06,07 */ 1408#define ARCMSR_ADAP_66MHZ 0x20 1409/* 1410**============================================================================== 1411** 0x08 : revision ID 1412** Bit Default Description 1413** 07:00 00000000 Revision ID (RID): '00h' indicating bridge A-0 stepping. 1414**============================================================================== 1415*/ 1416#define ARCMSR_PCI2PCI_REVISIONID_REG 0x08 /*byte*/ 1417/* 1418**============================================================================== 1419** 0x0b-0x09 : 0180_00 (class code 1,native pci mode ) 1420** Bit Default Description 1421** 23:16 06h Base Class Code (BCC): Indicates that this is a bridge device. 1422** 15:08 04h Sub Class Code (SCC): Indicates this is of type PCI-to-PCI bridge. 1423** 07:00 00h Programming Interface (PIF): Indicates that this is standard (non-subtractive) PCI-PCI bridge. 1424**============================================================================== 1425*/ 1426#define ARCMSR_PCI2PCI_CLASSCODE_REG 0x09 /*3bytes*/ 1427/* 1428**============================================================================== 1429** 0x0c : cache line size 1430** Bit Default Description 1431** 07:00 00h Cache Line Size (CLS): Designates the cache line size in 32-bit dword units. 1432** The contents of this register are factored into 1433** internal policy decisions associated with memory read prefetching, 1434** and the promotion of Memory Write transactions to MWI transactions. 1435** Valid cache line sizes are 8 and 16 dwords. 1436** When the cache line size is set to an invalid value, 1437** bridge behaves as though the cache line size was set to 00h. 1438**============================================================================== 1439*/ 1440#define ARCMSR_PCI2PCI_PRIMARY_CACHELINESIZE_REG 0x0C /*byte*/ 1441/* 1442**============================================================================== 1443** 0x0d : latency timer (number of pci clock 00-ff ) 1444** Bit Default Description 1445** Primary Latency Timer (PTV): 1446** 07:00 00h (Conventional PCI) Conventional PCI Mode: Primary bus Master latency timer. Indicates the number of PCI clock cycles, 1447** referenced from the assertion of FRAME# to the expiration of the timer, 1448** when bridge may continue as master of the current transaction. All bits are writable, 1449** resulting in a granularity of 1 PCI clock cycle. 1450** When the timer expires (i.e., equals 00h) 1451** bridge relinquishes the bus after the first data transfer 1452** when its PCI bus grant has been deasserted. 1453** or 40h (PCI-X) PCI-X Mode: Primary bus Master latency timer. 1454** Indicates the number of PCI clock cycles, 1455** referenced from the assertion of FRAME# to the expiration of the timer, 1456** when bridge may continue as master of the current transaction. 1457** All bits are writable, resulting in a granularity of 1 PCI clock cycle. 1458** When the timer expires (i.e., equals 00h) bridge relinquishes the bus at the next ADB. 1459** (Except in the case where MLT expires within 3 data phases 1460** of an ADB.In this case bridge continues on 1461** until it reaches the next ADB before relinquishing the bus.) 1462**============================================================================== 1463*/ 1464#define ARCMSR_PCI2PCI_PRIMARY_LATENCYTIMER_REG 0x0D /*byte*/ 1465/* 1466**============================================================================== 1467** 0x0e : (header type,single function ) 1468** Bit Default Description 1469** 07 0 Multi-function device (MVD): 80331 is a single-function device. 1470** 06:00 01h Header Type (HTYPE): Defines the layout of addresses 10h through 3Fh in configuration space. 1471** Returns ��01h�� when read indicating 1472** that the register layout conforms to the standard PCI-to-PCI bridge layout. 1473**============================================================================== 1474*/ 1475#define ARCMSR_PCI2PCI_HEADERTYPE_REG 0x0E /*byte*/ 1476/* 1477**============================================================================== 1478** 0x0f : 1479**============================================================================== 1480*/ 1481/* 1482**============================================================================== 1483** 0x13-0x10 : 1484** PCI CFG Base Address #0 (0x10) 1485**============================================================================== 1486*/ 1487/* 1488**============================================================================== 1489** 0x17-0x14 : 1490** PCI CFG Base Address #1 (0x14) 1491**============================================================================== 1492*/ 1493/* 1494**============================================================================== 1495** 0x1b-0x18 : 1496** PCI CFG Base Address #2 (0x18) 1497**-----------------0x1A,0x19,0x18--Bus Number Register - BNR 1498** Bit Default Description 1499** 23:16 00h Subordinate Bus Number (SBBN): Indicates the highest PCI bus number below this bridge. 1500** Any Type 1 configuration cycle 1501** on the primary bus whose bus number is greater than the secondary bus number, 1502** and less than or equal to the subordinate bus number 1503** is forwarded unaltered as a Type 1 configuration cycle on the secondary PCI bus. 1504** 15:08 00h Secondary Bus Number (SCBN): Indicates the bus number of PCI to which the secondary interface is connected. 1505** Any Type 1 configuration cycle matching this bus number 1506** is translated to a Type 0 configuration cycle (or a Special Cycle) 1507** before being executed on bridge's secondary PCI bus. 1508** 07:00 00h Primary Bus Number (PBN): Indicates bridge primary bus number. 1509** Any Type 1 configuration cycle on the primary interface 1510** with a bus number that is less than the contents 1511** of this register field does not be claimed by bridge. 1512**-----------------0x1B--Secondary Latency Timer Register - SLTR 1513** Bit Default Description 1514** Secondary Latency Timer (STV): 1515** 07:00 00h (Conventional PCI) Conventional PCI Mode: Secondary bus Master latency timer. 1516** Indicates the number of PCI clock cycles, 1517** referenced from the assertion of FRAME# to the expiration of the timer, 1518** when bridge may continue as master of the current transaction. All bits are writable, 1519** resulting in a granularity of 1 PCI clock cycle. 1520** When the timer expires (i.e., equals 00h) 1521** bridge relinquishes the bus after the first data transfer 1522** when its PCI bus grant has been deasserted. 1523** or 40h (PCI-X) PCI-X Mode: Secondary bus Master latency timer. 1524** Indicates the number of PCI clock cycles,referenced from the assertion of FRAME# 1525** to the expiration of the timer, 1526** when bridge may continue as master of the current transaction. All bits are writable, 1527** resulting in a granularity of 1 PCI clock cycle. 1528** When the timer expires (i.e., equals 00h) bridge relinquishes the bus at the next ADB. 1529** (Except in the case where MLT expires within 3 data phases of an ADB. 1530** In this case bridge continues on until it reaches the next ADB 1531** before relinquishing the bus) 1532**============================================================================== 1533*/ 1534#define ARCMSR_PCI2PCI_PRIMARY_BUSNUMBER_REG 0x18 /*3byte 0x1A,0x19,0x18*/ 1535#define ARCMSR_PCI2PCI_SECONDARY_BUSNUMBER_REG 0x19 /*byte*/ 1536#define ARCMSR_PCI2PCI_SUBORDINATE_BUSNUMBER_REG 0x1A /*byte*/ 1537#define ARCMSR_PCI2PCI_SECONDARY_LATENCYTIMER_REG 0x1B /*byte*/ 1538/* 1539**============================================================================== 1540** 0x1f-0x1c : 1541** PCI CFG Base Address #3 (0x1C) 1542**-----------------0x1D,0x1C--I/O Base and Limit Register - IOBL 1543** Bit Default Description 1544** 15:12 0h I/O Limit Address Bits [15:12]: Defines the top address of an address range to 1545** determine when to forward I/O transactions from one interface to the other. 1546** These bits correspond to address lines 15:12 for 4KB alignment. 1547** Bits 11:0 are assumed to be FFFh. 1548** 11:08 1h I/O Limit Addressing Capability: This field is hard-wired to 1h, indicating support 32-bit I/O addressing. 1549** 07:04 0h I/O Base Address Bits [15:12]: Defines the bottom address of 1550** an address range to determine when to forward I/O transactions 1551** from one interface to the other. 1552** These bits correspond to address lines 15:12 for 4KB alignment. 1553** Bits 11:0 are assumed to be 000h. 1554** 03:00 1h I/O Base Addressing Capability: This is hard-wired to 1h, indicating support for 32-bit I/O addressing. 1555**-----------------0x1F,0x1E--Secondary Status Register - SSR 1556** Bit Default Description 1557** 15 0b Detected Parity Error: The bridge sets this bit to a 1b whenever it detects an address, 1558** attribute or data parity error on its secondary interface. 1559** 14 0b Received System Error: The bridge sets this bit when it samples SERR# asserted on its secondary bus interface. 1560** 13 0b Received Master Abort: The bridge sets this bit to a 1b when, 1561** acting as the initiator on the secondary bus, 1562** it's transaction (with the exception of special cycles) 1563** has been terminated with a Master Abort. 1564** 12 0b Received Target Abort: The bridge sets this bit to a 1b when, 1565** acting as the initiator on the secondary bus, 1566** it's transaction has been terminated with a Target Abort. 1567** 11 0b Signaled Target Abort: The bridge sets this bit to a 1b when it, 1568** as the target of a transaction, terminates it with a Target Abort. 1569** In PCI-X mode this bit is also set when it forwards a SCM with a target abort error code. 1570** 10:09 01b DEVSEL# Timing: Indicates slowest response to a non-configuration command on the secondary interface. 1571** Returns ��01b�� when read, indicating that bridge responds no slower than with medium timing. 1572** 08 0b Master Data Parity Error: The bridge sets this bit to a 1b when all of the following conditions are true: 1573** The bridge is the current master on the secondary bus 1574** S_PERR# is detected asserted or is asserted by bridge 1575** The Parity Error Response bit is set in the Command register 1576** 07 1b Fast Back-to-Back Capable (FBC): Indicates that the secondary interface of bridge can receive fast back-to-back cycles. 1577** 06 0b Reserved 1578** 05 1b 66 MHz Capable (C66): Indicates the secondary interface of the bridge is 66 MHz capable. 1579** 1 = 1580** 04:00 00h Reserved 1581**============================================================================== 1582*/ 1583#define ARCMSR_PCI2PCI_IO_BASE_REG 0x1C /*byte*/ 1584#define ARCMSR_PCI2PCI_IO_LIMIT_REG 0x1D /*byte*/ 1585#define ARCMSR_PCI2PCI_SECONDARY_STATUS_REG 0x1E /*word: 0x1F,0x1E */ 1586/* 1587**============================================================================== 1588** 0x23-0x20 : 1589** PCI CFG Base Address #4 (0x20) 1590**-----------------0x23,0x22,0x21,0x20--Memory Base and Limit Register - MBL 1591** Bit Default Description 1592** 31:20 000h Memory Limit: These 12 bits are compared with P_AD[31:20] of the incoming address to determine 1593** the upper 1MB aligned value (exclusive) of the range. 1594** The incoming address must be less than or equal to this value. 1595** For the purposes of address decoding the lower 20 address bits (P_AD[19:0] 1596** are assumed to be F FFFFh. 1597** 19:16 0h Reserved. 1598** 15:04 000h Memory Base: These 12 bits are compared with bits P_AD[31:20] 1599** of the incoming address to determine the lower 1MB 1600** aligned value (inclusive) of the range. 1601** The incoming address must be greater than or equal to this value. 1602** For the purposes of address decoding the lower 20 address bits (P_AD[19:0]) 1603** are assumed to be 0 0000h. 1604** 03:00 0h Reserved. 1605**============================================================================== 1606*/ 1607#define ARCMSR_PCI2PCI_NONPREFETCHABLE_MEMORY_BASE_REG 0x20 /*word: 0x21,0x20 */ 1608#define ARCMSR_PCI2PCI_NONPREFETCHABLE_MEMORY_LIMIT_REG 0x22 /*word: 0x23,0x22 */ 1609/* 1610**============================================================================== 1611** 0x27-0x24 : 1612** PCI CFG Base Address #5 (0x24) 1613**-----------------0x27,0x26,0x25,0x24--Prefetchable Memory Base and Limit Register - PMBL 1614** Bit Default Description 1615** 31:20 000h Prefetchable Memory Limit: These 12 bits are compared with P_AD[31:20] of the incoming address to determine 1616** the upper 1MB aligned value (exclusive) of the range. 1617** The incoming address must be less than or equal to this value. 1618** For the purposes of address decoding the lower 20 address bits (P_AD[19:0] 1619** are assumed to be F FFFFh. 1620** 19:16 1h 64-bit Indicator: Indicates that 64-bit addressing is supported. 1621** 15:04 000h Prefetchable Memory Base: These 12 bits are compared with bits P_AD[31:20] 1622** of the incoming address to determine the lower 1MB aligned value (inclusive) 1623** of the range. 1624** The incoming address must be greater than or equal to this value. 1625** For the purposes of address decoding the lower 20 address bits (P_AD[19:0]) 1626** are assumed to be 0 0000h. 1627** 03:00 1h 64-bit Indicator: Indicates that 64-bit addressing is supported. 1628**============================================================================== 1629*/ 1630#define ARCMSR_PCI2PCI_PREFETCHABLE_MEMORY_BASE_REG 0x24 /*word: 0x25,0x24 */ 1631#define ARCMSR_PCI2PCI_PREFETCHABLE_MEMORY_LIMIT_REG 0x26 /*word: 0x27,0x26 */ 1632/* 1633**============================================================================== 1634** 0x2b-0x28 : 1635** Bit Default Description 1636** 31:00 00000000h Prefetchable Memory Base Upper Portion: All bits are read/writable 1637** bridge supports full 64-bit addressing. 1638**============================================================================== 1639*/ 1640#define ARCMSR_PCI2PCI_PREFETCHABLE_MEMORY_BASE_UPPER32_REG 0x28 /*dword: 0x2b,0x2a,0x29,0x28 */ 1641/* 1642**============================================================================== 1643** 0x2f-0x2c : 1644** Bit Default Description 1645** 31:00 00000000h Prefetchable Memory Limit Upper Portion: All bits are read/writable 1646** bridge supports full 64-bit addressing. 1647**============================================================================== 1648*/ 1649#define ARCMSR_PCI2PCI_PREFETCHABLE_MEMORY_LIMIT_UPPER32_REG 0x2C /*dword: 0x2f,0x2e,0x2d,0x2c */ 1650/* 1651**============================================================================== 1652** 0x33-0x30 : 1653** Bit Default Description 1654** 07:00 DCh Capabilities Pointer: Pointer to the first CAP ID entry in the capabilities list is at DCh in PCI configuration 1655** space. (Power Management Capability Registers) 1656**============================================================================== 1657*/ 1658#define ARCMSR_PCI2PCI_CAPABILITIES_POINTER_REG 0x34 /*byte*/ 1659/* 1660**============================================================================== 1661** 0x3b-0x35 : reserved 1662**============================================================================== 1663*/ 1664/* 1665**============================================================================== 1666** 0x3d-0x3c : 1667** 1668** Bit Default Description 1669** 15:08 00h Interrupt Pin (PIN): Bridges do not support the generation of interrupts. 1670** 07:00 00h Interrupt Line (LINE): The bridge does not generate interrupts, so this is reserved as '00h'. 1671**============================================================================== 1672*/ 1673#define ARCMSR_PCI2PCI_PRIMARY_INTERRUPT_LINE_REG 0x3C /*byte*/ 1674#define ARCMSR_PCI2PCI_PRIMARY_INTERRUPT_PIN_REG 0x3D /*byte*/ 1675/* 1676**============================================================================== 1677** 0x3f-0x3e : 1678** Bit Default Description 1679** 15:12 0h Reserved 1680** 11 0b Discard Timer SERR# Enable: Controls the generation of SERR# on the primary interface (P_SERR#) in response 1681** to a timer discard on either the primary or secondary interface. 1682** 0b=SERR# is not asserted. 1683** 1b=SERR# is asserted. 1684** 10 0b Discard Timer Status (DTS): This bit is set to a '1b' when either the primary or secondary discard timer expires. 1685** The delayed completion is then discarded. 1686** 09 0b Secondary Discard Timer (SDT): Sets the maximum number of PCI clock cycles 1687** that bridge waits for an initiator on the secondary bus 1688** to repeat a delayed transaction request. 1689** The counter starts when the delayed transaction completion is ready 1690** to be returned to the initiator. 1691** When the initiator has not repeated the transaction 1692** at least once before the counter expires,bridge 1693** discards the delayed transaction from its queues. 1694** 0b=The secondary master time-out counter is 2 15 PCI clock cycles. 1695** 1b=The secondary master time-out counter is 2 10 PCI clock cycles. 1696** 08 0b Primary Discard Timer (PDT): Sets the maximum number of PCI clock cycles 1697** that bridge waits for an initiator on the primary bus 1698** to repeat a delayed transaction request. 1699** The counter starts when the delayed transaction completion 1700** is ready to be returned to the initiator. 1701** When the initiator has not repeated the transaction 1702** at least once before the counter expires, 1703** bridge discards the delayed transaction from its queues. 1704** 0b=The primary master time-out counter is 2 15 PCI clock cycles. 1705** 1b=The primary master time-out counter is 2 10 PCI clock cycles. 1706** 07 0b Fast Back-to-Back Enable (FBE): The bridge does not initiate back to back transactions. 1707** 06 0b Secondary Bus Reset (SBR): 1708** When cleared to 0b: The bridge deasserts S_RST#, 1709** when it had been asserted by writing this bit to a 1b. 1710** When set to 1b: The bridge asserts S_RST#. 1711** 05 0b Master Abort Mode (MAM): Dictates bridge behavior on the initiator bus 1712** when a master abort termination occurs in response to 1713** a delayed transaction initiated by bridge on the target bus. 1714** 0b=The bridge asserts TRDY# in response to a non-locked delayed transaction, 1715** and returns FFFF FFFFh when a read. 1716** 1b=When the transaction had not yet been completed on the initiator bus 1717** (e.g.,delayed reads, or non-posted writes), 1718** then bridge returns a Target Abort in response to the original requester 1719** when it returns looking for its delayed completion on the initiator bus. 1720** When the transaction had completed on the initiator bus (e.g., a PMW), 1721** then bridge asserts P_SERR# (when enabled). 1722** For PCI-X transactions this bit is an enable for the assertion of P_SERR# due to a master abort 1723** while attempting to deliver a posted memory write on the destination bus. 1724** 04 0b VGA Alias Filter Enable: This bit dictates bridge behavior in conjunction with the VGA enable bit 1725** (also of this register), 1726** and the VGA Palette Snoop Enable bit (Command Register). 1727** When the VGA enable, or VGA Palette Snoop enable bits are on (i.e., 1b) 1728** the VGA Aliasing bit for the corresponding enabled functionality,: 1729** 0b=Ignores address bits AD[15:10] when decoding VGA I/O addresses. 1730** 1b=Ensures that address bits AD[15:10] equal 000000b when decoding VGA I/O addresses. 1731** When all VGA cycle forwarding is disabled, (i.e., VGA Enable bit =0b and VGA Palette Snoop bit =0b), 1732** then this bit has no impact on bridge behavior. 1733** 03 0b VGA Enable: Setting this bit enables address decoding 1734** and transaction forwarding of the following VGA transactions from the primary bus 1735** to the secondary bus: 1736** frame buffer memory addresses 000A0000h:000BFFFFh, 1737** VGA I/O addresses 3B0:3BBh and 3C0h:3DFh, where AD[31:16]=��0000h?** ?and AD[15:10] are either not decoded (i.e., don't cares), 1738** or must be ��000000b�� 1739** depending upon the state of the VGA Alias Filter Enable bit. (bit(4) of this register) 1740** I/O and Memory Enable bits must be set in the Command register 1741** to enable forwarding of VGA cycles. 1742** 02 0b ISA Enable: Setting this bit enables special handling 1743** for the forwarding of ISA I/O transactions that fall within the address range 1744** specified by the I/O Base and Limit registers, 1745** and are within the lowest 64Kbyte of the I/O address map 1746** (i.e., 0000 0000h - 0000 FFFFh). 1747** 0b=All I/O transactions that fall within the I/O Base 1748** and Limit registers' specified range are forwarded 1749** from primary to secondary unfiltered. 1750** 1b=Blocks the forwarding from primary to secondary 1751** of the top 768 bytes of each 1Kbyte alias. 1752** On the secondary the top 768 bytes of each 1K alias 1753** are inversely decoded and forwarded 1754** from secondary to primary. 1755** 01 0b SERR# Forward Enable: 0b=The bridge does not assert P_SERR# as a result of an S_SERR# assertion. 1756** 1b=The bridge asserts P_SERR# whenever S_SERR# is detected 1757** asserted provided the SERR# Enable bit is set (PCI Command Register bit(8)=1b). 1758** 00 0b Parity Error Response: This bit controls bridge response to a parity error 1759** that is detected on its secondary interface. 1760** 0b=When a data parity error is detected bridge does not assert S_PERR#. 1761** Also bridge does not assert P_SERR# in response to a detected address 1762** or attribute parity error. 1763** 1b=When a data parity error is detected bridge asserts S_PERR#. 1764** The bridge also asserts P_SERR# (when enabled globally via bit(8) 1765** of the Command register) 1766** in response to a detected address or attribute parity error. 1767**============================================================================== 1768*/ 1769#define ARCMSR_PCI2PCI_BRIDGE_CONTROL_REG 0x3E /*word*/ 1770/* 1771************************************************************************** 1772** Device Specific Registers 40-A7h 1773************************************************************************** 1774** ---------------------------------------------------------------------------------------------------------- 1775** | Byte 3 | Byte 2 | Byte 1 | Byte 0 | Configu-ration Byte Offset 1776** ---------------------------------------------------------------------------------------------------------- 1777** | Bridge Control 0 | Arbiter Control/Status | Reserved | 40h 1778** ---------------------------------------------------------------------------------------------------------- 1779** | Bridge Control 2 | Bridge Control 1 | 44h 1780** ---------------------------------------------------------------------------------------------------------- 1781** | Reserved | Bridge Status | 48h 1782** ---------------------------------------------------------------------------------------------------------- 1783** | Reserved | 4Ch 1784** ---------------------------------------------------------------------------------------------------------- 1785** | Prefetch Policy | Multi-Transaction Timer | 50h 1786** ---------------------------------------------------------------------------------------------------------- 1787** | Reserved | Pre-boot Status | P_SERR# Assertion Control | 54h 1788** ---------------------------------------------------------------------------------------------------------- 1789** | Reserved | Reserved | Secondary Decode Enable | 58h 1790** ---------------------------------------------------------------------------------------------------------- 1791** | Reserved | Secondary IDSEL | 5Ch 1792** ---------------------------------------------------------------------------------------------------------- 1793** | Reserved | 5Ch 1794** ---------------------------------------------------------------------------------------------------------- 1795** | Reserved | 68h:CBh 1796** ---------------------------------------------------------------------------------------------------------- 1797************************************************************************** 1798**============================================================================== 1799** 0x42-0x41: Secondary Arbiter Control/Status Register - SACSR 1800** Bit Default Description 1801** 15:12 1111b Grant Time-out Violator: This field indicates the agent that violated the Grant Time-out rule 1802** (PCI=16 clocks,PCI-X=6 clocks). 1803** Note that this field is only meaningful when: 1804** # Bit[11] of this register is set to 1b, 1805** indicating that a Grant Time-out violation had occurred. 1806** # bridge internal arbiter is enabled. 1807** Bits[15:12] Violating Agent (REQ#/GNT# pair number) 1808** 0000b REQ#/GNT#[0] 1809** 0001b REQ#/GNT#[1] 1810** 0010b REQ#/GNT#[2] 1811** 0011b REQ#/GNT#[3] 1812** 1111b Default Value (no violation detected) 1813** When bit[11] is cleared by software, this field reverts back to its default value. 1814** All other values are Reserved 1815** 11 0b Grant Time-out Occurred: When set to 1b, 1816** this indicates that a Grant Time-out error had occurred involving one of the secondary bus agents. 1817** Software clears this bit by writing a 1b to it. 1818** 10 0b Bus Parking Control: 0=During bus idle, bridge parks the bus on the last master to use the bus. 1819** 1=During bus idle, bridge parks the bus on itself. 1820** The bus grant is removed from the last master and internally asserted to bridge. 1821** 09:08 00b Reserved 1822** 07:00 0000 0000b Secondary Bus Arbiter Priority Configuration: The bridge secondary arbiter provides two rings of arbitration priority. 1823** Each bit of this field assigns its corresponding secondary 1824** bus master to either the high priority arbiter ring (1b) 1825** or to the low priority arbiter ring (0b). 1826** Bits [3:0] correspond to request inputs S_REQ#[3:0], respectively. 1827** Bit [6] corresponds to the bridge internal secondary bus request 1828** while Bit [7] corresponds to the SATU secondary bus request. 1829** Bits [5:4] are unused. 1830** 0b=Indicates that the master belongs to the low priority group. 1831** 1b=Indicates that the master belongs to the high priority group 1832**================================================================================= 1833** 0x43: Bridge Control Register 0 - BCR0 1834** Bit Default Description 1835** 07 0b Fully Dynamic Queue Mode: 0=The number of Posted write transactions is limited to eight 1836** and the Posted Write data is limited to 4KB. 1837** 1=Operation in fully dynamic queue mode. The bridge enqueues up to 1838** 14 Posted Memory Write transactions and 8KB of posted write data. 1839** 06:03 0H Reserved. 1840** 02 0b Upstream Prefetch Disable: This bit disables bridge ability 1841** to perform upstream prefetch operations for Memory 1842** Read requests received on its secondary interface. 1843** This bit also controls the bridge's ability to generate advanced read commands 1844** when forwarding a Memory Read Block transaction request upstream from a PCI-X bus 1845** to a Conventional PCI bus. 1846** 0b=bridge treats all upstream Memory Read requests as though they target prefetchable memory. 1847** The use of Memory Read Line and Memory Read 1848** Multiple is enabled when forwarding a PCI-X Memory Read Block request 1849** to an upstream bus operating in Conventional PCI mode. 1850** 1b=bridge treats upstream PCI Memory Read requests as though 1851** they target non-prefetchable memory and forwards upstream PCI-X Memory 1852** Read Block commands as Memory Read 1853** when the primary bus is operating 1854** in Conventional PCI mode. 1855** NOTE: This bit does not affect bridge ability to perform read prefetching 1856** when the received command is Memory Read Line or Memory Read Multiple. 1857**================================================================================= 1858** 0x45-0x44: Bridge Control Register 1 - BCR1 (Sheet 2 of 2) 1859** Bit Default Description 1860** 15:08 0000000b Reserved 1861** 07:06 00b Alias Command Mapping: This two bit field determines how bridge handles PCI-X ��Alias�� commands, 1862** specifically the Alias to Memory Read Block and Alias to Memory Write Block commands. 1863** The three options for handling these alias commands are to either pass it as is, 1864** re-map to the actual block memory read/write command encoding, or ignore 1865** the transaction forcing a Master Abort to occur on the Origination Bus. 1866** Bit (7:6) Handling of command 1867** 0 0 Re-map to Memory Read/Write Block before forwarding 1868** 0 1 Enqueue and forward the alias command code unaltered 1869** 1 0 Ignore the transaction, forcing Master Abort 1870** 1 1 Reserved 1871** 05 1b Watchdog Timers Disable: Disables or enables all 2 24 Watchdog Timers in both directions. 1872** The watchdog timers are used to detect prohibitively long latencies in the system. 1873** The watchdog timer expires when any Posted Memory Write (PMW), Delayed Request, 1874** or Split Requests (PCI-X mode) is not completed within 2 24 events 1875** (��events�� are defined as PCI Clocks when operating in PCI-X mode, 1876** and as the number of times being retried when operating in Conventional PCI mode) 1877** 0b=All 2 24 watchdog timers are enabled. 1878** 1b=All 2 24 watchdog timers are disabled and there is no limits to 1879** the number of attempts bridge makes when initiating a PMW, 1880** transacting a Delayed Transaction, or how long it waits for 1881** a split completion corresponding to one of its requests. 1882** 04 0b GRANT# time-out disable: This bit enables/disables the GNT# time-out mechanism. 1883** Grant time-out is 16 clocks for conventional PCI, and 6 clocks for PCI-X. 1884** 0b=The Secondary bus arbiter times out an agent 1885** that does not assert FRAME# within 16/6 clocks of receiving its grant, 1886** once the bus has gone idle. 1887** The time-out counter begins as soon as the bus goes idle with the new GNT# asserted. 1888** An infringing agent does not receive a subsequent GNT# 1889** until it de-asserts its REQ# for at least one clock cycle. 1890** 1b=GNT# time-out mechanism is disabled. 1891** 03 00b Reserved. 1892** 02 0b Secondary Discard Timer Disable: This bit enables/disables bridge secondary delayed transaction discard mechanism. 1893** The time out mechanism is used to ensure that initiators 1894** of delayed transactions return for their delayed completion data/status 1895** within a reasonable amount of time after it is available from bridge. 1896** 0b=The secondary master time-out counter is enabled 1897** and uses the value specified by the Secondary Discard Timer bit 1898** (see Bridge Control Register). 1899** 1b=The secondary master time-out counter is disabled. 1900** The bridge waits indefinitely for a secondary bus master 1901** to repeat a delayed transaction. 1902** 01 0b Primary Discard Timer Disable: This bit enables/disables bridge primary delayed transaction discard mechanism. 1903** The time out mechanism is used to ensure that initiators 1904** of delayed transactions return for their delayed completion data/status 1905** within a reasonable amount of time after it is available from bridge. 1906** 0b=The primary master time-out counter is enabled and uses the value specified 1907** by the Primary Discard Timer bit (see Bridge Control Register). 1908** 1b=The secondary master time-out counter is disabled. 1909** The bridge waits indefinitely for a secondary bus master 1910** to repeat a delayed transaction. 1911** 00 0b Reserved 1912**================================================================================= 1913** 0x47-0x46: Bridge Control Register 2 - BCR2 1914** Bit Default Description 1915** 15:07 0000b Reserved. 1916** 06 0b Global Clock Out Disable (External Secondary Bus Clock Source Enable): 1917** This bit disables all of the secondary PCI clock outputs including 1918** the feedback clock S_CLKOUT. 1919** This means that the user is required to provide an S_CLKIN input source. 1920** 05:04 11 (66 MHz) Preserved. 1921** 01 (100 MHz) 1922** 00 (133 MHz) 1923** 03:00 Fh (100 MHz & 66 MHz) 1924** 7h (133 MHz) 1925** This 4 bit field provides individual enable/disable mask bits for each of bridge 1926** secondary PCI clock outputs. Some, or all secondary clock outputs (S_CLKO[3:0]) 1927** default to being enabled following the rising edge of P_RST#, depending on the 1928** frequency of the secondary bus clock: 1929** �E Designs with 100 MHz (or lower) Secondary PCI clock power up with 1930** all four S_CLKOs enabled by default. (SCLKO[3:0])�P 1931** �E Designs with 133 MHz Secondary PCI clock power up 1932** with the lower order 3 S_CLKOs enabled by default. 1933** (S_CLKO[2:0]) Only those SCLKs that power up enabled by can be connected 1934** to downstream device clock inputs. 1935**================================================================================= 1936** 0x49-0x48: Bridge Status Register - BSR 1937** Bit Default Description 1938** 15 0b Upstream Delayed Transaction Discard Timer Expired: This bit is set to a 1b and P_SERR# 1939** is conditionally asserted when the secondary discard timer expires. 1940** 14 0b Upstream Delayed/Split Read Watchdog Timer Expired: 1941** Conventional PCI Mode: This bit is set to a 1b and P_SERR# 1942** is conditionally asserted when bridge discards an upstream delayed read ** ** transaction request after 2 24 retries following the initial retry. 1943** PCI-X Mode: This bit is set to a 1b and P_SERR# is conditionally asserted 1944** when bridge discards an upstream split read request 1945** after waiting in excess of 2 24 clocks for the corresponding 1946** Split Completion to arrive. 1947** 13 0b Upstream Delayed/Split Write Watchdog Timer Expired: 1948** Conventional PCI Mode: This bit is set to a 1b and P_SERR# 1949** is conditionally asserted when bridge discards an upstream delayed write ** ** transaction request after 2 24 retries following the initial retry. 1950** PCI-X Mode: This bit is set to a 1b and P_SERR# 1951** is conditionally asserted when bridge discards an upstream split write request ** after waiting in excess of 2 24 clocks for the corresponding 1952** Split Completion to arrive. 1953** 12 0b Master Abort during Upstream Posted Write: This bit is set to a 1b and P_SERR# 1954** is conditionally asserted when a Master Abort occurs as a result of an attempt, 1955** by bridge, to retire a PMW upstream. 1956** 11 0b Target Abort during Upstream Posted Write: This bit is set to a 1b and P_SERR# 1957** is conditionally asserted when a Target Abort occurs as a result of an attempt, 1958** by bridge, to retire a PMW upstream. 1959** 10 0b Upstream Posted Write Data Discarded: This bit is set to a 1b and P_SERR# 1960** is conditionally asserted when bridge discards an upstream PMW transaction 1961** after receiving 2 24 target retries from the primary bus target 1962** 09 0b Upstream Posted Write Data Parity Error: This bit is set to a 1b and P_SERR# 1963** is conditionally asserted when a data parity error is detected by bridge 1964** while attempting to retire a PMW upstream 1965** 08 0b Secondary Bus Address Parity Error: This bit is set to a 1b and P_SERR# 1966** is conditionally asserted when bridge detects an address parity error on 1967** the secondary bus. 1968** 07 0b Downstream Delayed Transaction Discard Timer Expired: This bit is set to a 1b and P_SERR# 1969** is conditionally asserted when the primary bus discard timer expires. 1970** 06 0b Downstream Delayed/Split Read Watchdog Timer Expired: 1971** Conventional PCI Mode: This bit is set to a 1b and P_SERR# 1972** is conditionally asserted when bridge discards a downstream delayed read ** ** transaction request after receiving 2 24 target retries 1973** from the secondary bus target. 1974** PCI-X Mode: This bit is set to a 1b and P_SERR# is conditionally asserted 1975** when bridge discards a downstream split read request 1976** after waiting in excess of 2 24 clocks for the corresponding 1977** Split Completion to arrive. 1978** 05 0b Downstream Delayed Write/Split Watchdog Timer Expired: 1979** Conventional PCI Mode: This bit is set to a 1b and P_SERR# is conditionally asserted 1980** when bridge discards a downstream delayed write transaction request 1981** after receiving 2 24 target retries from the secondary bus target. 1982** PCI-X Mode: This bit is set to a 1b and P_SERR# 1983** is conditionally asserted when bridge discards a downstream 1984** split write request after waiting in excess of 2 24 clocks 1985** for the corresponding Split Completion to arrive. 1986** 04 0b Master Abort during Downstream Posted Write: This bit is set to a 1b and P_SERR# 1987** is conditionally asserted when a Master Abort occurs as a result of an attempt, 1988** by bridge, to retire a PMW downstream. 1989** 03 0b Target Abort during Downstream Posted Write: This bit is set to a 1b and P_SERR# is conditionally asserted 1990** when a Target Abort occurs as a result of an attempt, by bridge, 1991** to retire a PMW downstream. 1992** 02 0b Downstream Posted Write Data Discarded: This bit is set to a 1b and P_SERR# 1993** is conditionally asserted when bridge discards a downstream PMW transaction 1994** after receiving 2 24 target retries from the secondary bus target 1995** 01 0b Downstream Posted Write Data Parity Error: This bit is set to a 1b and P_SERR# 1996** is conditionally asserted when a data parity error is detected by bridge 1997** while attempting to retire a PMW downstream. 1998** 00 0b Primary Bus Address Parity Error: This bit is set to a 1b and P_SERR# is conditionally asserted 1999** when bridge detects an address parity error on the primary bus. 2000**================================================================================== 2001** 0x51-0x50: Bridge Multi-Transaction Timer Register - BMTTR 2002** Bit Default Description 2003** 15:13 000b Reserved 2004** 12:10 000b GRANT# Duration: This field specifies the count (PCI clocks) 2005** that a secondary bus master has its grant maintained in order to enable 2006** multiple transactions to execute within the same arbitration cycle. 2007** Bit[02:00] GNT# Extended Duration 2008** 000 MTT Disabled (Default=no GNT# extension) 2009** 001 16 clocks 2010** 010 32 clocks 2011** 011 64 clocks 2012** 100 128 clocks 2013** 101 256 clocks 2014** 110 Invalid (treated as 000) 2015** 111 Invalid (treated as 000) 2016** 09:08 00b Reserved 2017** 07:00 FFh MTT Mask: This field enables/disables MTT usage for each REQ#/GNT# 2018** pair supported by bridge secondary arbiter. 2019** Bit(7) corresponds to SATU internal REQ#/GNT# pair, 2020** bit(6) corresponds to bridge internal REQ#/GNT# pair, 2021** bit(5) corresponds to REQ#/GNT#(5) pair, etc. 2022** When a given bit is set to 1b, its corresponding REQ#/GNT# 2023** pair is enabled for MTT functionality as determined by bits(12:10) of this register. 2024** When a given bit is cleared to 0b, its corresponding REQ#/GNT# pair is disabled from using the MTT. 2025**================================================================================== 2026** 0x53-0x52: Read Prefetch Policy Register - RPPR 2027** Bit Default Description 2028** 15:13 000b ReRead_Primary Bus: 3-bit field indicating the multiplication factor 2029** to be used in calculating the number of bytes to prefetch from the secondary bus interface on ** subsequent PreFetch operations given that the read demands were not satisfied 2030** using the FirstRead parameter. 2031** The default value of 000b correlates to: Command Type Hardwired pre-fetch amount Memory Read 4 DWORDs 2032** Memory Read Line 1 cache lines Memory Read Multiple 2 cache lines 2033** 12:10 000b FirstRead_Primary Bus: 3-bit field indicating the multiplication factor to be used in calculating 2034** the number of bytes to prefetch from the secondary bus interface 2035** on the initial PreFetch operation. 2036** The default value of 000b correlates to: Command Type Hardwired pre-fetch amount Memory Read 4 DWORDs 2037** Memory Read Line 1 cache line Memory Read Multiple 2 cache lines 2038** 09:07 010b ReRead_Secondary Bus: 3-bit field indicating the multiplication factor to be used 2039** in calculating the number of bytes to prefetch from the primary 2040** bus interface on subsequent PreFetch operations given 2041** that the read demands were not satisfied using 2042** the FirstRead parameter. 2043** The default value of 010b correlates to: Command Type Hardwired pre-fetch a 2044** mount Memory Read 3 cache lines Memory Read Line 3 cache lines 2045** Memory Read Multiple 6 cache lines 2046** 06:04 000b FirstRead_Secondary Bus: 3-bit field indicating the multiplication factor to be used 2047** in calculating the number of bytes to prefetch from 2048** the primary bus interface on the initial PreFetch operation. 2049** The default value of 000b correlates to: Command Type Hardwired pre-fetch amount 2050** Memory Read 4 DWORDs Memory Read Line 1 cache line Memory Read Multiple 2 cache lines 2051** 03:00 1111b Staged Prefetch Enable: This field enables/disables the FirstRead/ReRead pre-fetch 2052** algorithm for the secondary and the primary bus interfaces. 2053** Bit(3) is a ganged enable bit for REQ#/GNT#[7:3], and bits(2:0) provide individual 2054** enable bits for REQ#/GNT#[2:0]. 2055** (bit(2) is the enable bit for REQ#/GNT#[2], etc...) 2056** 1b: enables the staged pre-fetch feature 2057** 0b: disables staged pre-fetch, 2058** and hardwires read pre-fetch policy to the following for 2059** Memory Read, 2060** Memory Read Line, 2061** and Memory Read Multiple commands: 2062** Command Type Hardwired Pre-Fetch Amount... 2063** Memory Read 4 DWORDs 2064** Memory Read Line 1 cache line 2065** Memory Read Multiple 2 cache lines 2066** NOTE: When the starting address is not cache line aligned, bridge pre-fetches Memory Read line commands 2067** only to the next higher cache line boundary.For non-cache line aligned Memory Read 2068** Multiple commands bridge pre-fetches only to the second cache line boundary encountered. 2069**================================================================================== 2070** 0x55-0x54: P_SERR# Assertion Control - SERR_CTL 2071** Bit Default Description 2072** 15 0b Upstream Delayed Transaction Discard Timer Expired: Dictates the bridge behavior 2073** in response to its discarding of a delayed transaction that was initiated from the primary bus. 2074** 0b=bridge asserts P_SERR#. 2075** 1b=bridge does not assert P_SERR# 2076** 14 0b Upstream Delayed/Split Read Watchdog Timer Expired: Dictates bridge behavior following expiration of the subject watchdog timer. 2077** 0b=bridge asserts P_SERR#. 2078** 1b=bridge does not assert P_SERR# 2079** 13 0b Upstream Delayed/Split Write Watchdog Timer Expired: Dictates bridge behavior following expiration of the subject watchdog timer. 2080** 0b=bridge asserts P_SERR#. 2081** 1b=bridge does not assert P_SERR# 2082** 12 0b Master Abort during Upstream Posted Write: Dictates bridge behavior following 2083** its having detected a Master Abort while attempting to retire one of its PMWs upstream. 2084** 0b=bridge asserts P_SERR#. 2085** 1b=bridge does not assert P_SERR# 2086** 11 0b Target Abort during Upstream Posted Write: Dictates bridge behavior following 2087** its having been terminated with Target Abort while attempting to retire one of its PMWs upstream. 2088** 0b=bridge asserts P_SERR#. 2089** 1b=bridge does not assert P_SERR# 2090** 10 0b Upstream Posted Write Data Discarded: Dictates bridge behavior in the event that 2091** it discards an upstream posted write transaction. 2092** 0b=bridge asserts P_SERR#. 2093** 1b=bridge does not assert P_SERR# 2094** 09 0b Upstream Posted Write Data Parity Error: Dictates bridge behavior 2095** when a data parity error is detected while attempting to retire on of its PMWs upstream. 2096** 0b=bridge asserts P_SERR#. 2097** 1b=bridge does not assert P_SERR# 2098** 08 0b Secondary Bus Address Parity Error: This bit dictates bridge behavior 2099** when it detects an address parity error on the secondary bus. 2100** 0b=bridge asserts P_SERR#. 2101** 1b=bridge does not assert P_SERR# 2102** 07 0b Downstream Delayed Transaction Discard Timer Expired: Dictates bridge behavior in response to 2103** its discarding of a delayed transaction that was initiated on the secondary bus. 2104** 0b=bridge asserts P_SERR#. 2105** 1b=bridge does not assert P_SERR# 2106** 06 0b Downstream Delayed/Split Read Watchdog Timer Expired: Dictates bridge behavior following expiration of the subject watchdog timer. 2107** 0b=bridge asserts P_SERR#. 2108** 1b=bridge does not assert P_SERR# 2109** 05 0b Downstream Delayed/Split Write Watchdog Timer Expired: Dictates bridge behavior following expiration of the subject watchdog timer. 2110** 0b=bridge asserts P_SERR#. 2111** 1b=bridge does not assert P_SERR# 2112** 04 0b Master Abort during Downstream Posted Write: Dictates bridge behavior following 2113** its having detected a Master Abort while attempting to retire one of its PMWs downstream. 2114** 0b=bridge asserts P_SERR#. 2115** 1b=bridge does not assert P_SERR# 2116** 03 0b Target Abort during Downstream Posted Write: Dictates bridge behavior following 2117** its having been terminated with Target Abort while attempting to retire one of its PMWs downstream. 2118** 0b=bridge asserts P_SERR#. 2119** 1b=bridge does not assert P_SERR# 2120** 02 0b Downstream Posted Write Data Discarded: Dictates bridge behavior in the event 2121** that it discards a downstream posted write transaction. 2122** 0b=bridge asserts P_SERR#. 2123** 1b=bridge does not assert P_SERR# 2124** 01 0b Downstream Posted Write Data Parity Error: Dictates bridge behavior 2125** when a data parity error is detected while attempting to retire on of its PMWs downstream. 2126** 0b=bridge asserts P_SERR#. 2127** 1b=bridge does not assert P_SERR# 2128** 00 0b Primary Bus Address Parity Error: This bit dictates bridge behavior 2129** when it detects an address parity error on the primary bus. 2130** 0b=bridge asserts P_SERR#. 2131** 1b=bridge does not assert P_SERR# 2132**=============================================================================== 2133** 0x56: Pre-Boot Status Register - PBSR 2134** Bit Default Description 2135** 07 1 Reserved 2136** 06 - Reserved - value indeterminate 2137** 05:02 0 Reserved 2138** 01 Varies with External State of S_133EN at PCI Bus Reset Secondary Bus Max Frequency Setting: 2139** This bit reflect captured S_133EN strap, 2140** indicating the maximum secondary bus clock frequency when in PCI-X mode. 2141** Max Allowable Secondary Bus Frequency 2142** ** S_133EN PCI-X Mode 2143** ** 0 100 MHz 2144** ** 1 133 MH 2145** 00 0b Reserved 2146**=============================================================================== 2147** 0x59-0x58: Secondary Decode Enable Register - SDER 2148** Bit Default Description 2149** 15:03 FFF1h Preserved. 2150** 02 Varies with External State of PRIVMEM at PCI Bus Reset Private Memory Space Enable - when set, 2151** bridge overrides its secondary inverse decode logic and not 2152** forward upstream any secondary bus initiated DAC Memory transactions with AD(63)=1b. 2153** This creates a private memory space on the Secondary PCI bus 2154** that allows peer-to-peer transactions. 2155** 01:00 10 2 Preserved. 2156**=============================================================================== 2157** 0x5D-0x5C: Secondary IDSEL Select Register - SISR 2158** Bit Default Description 2159** 15:10 000000 2 Reserved. 2160** 09 Varies with External State of PRIVDEV at PCI Bus Reset AD25- IDSEL Disable - When this bit is set, 2161** AD25 is deasserted for any possible Type 1 to Type 0 conversion. 2162** When this bit is clear, 2163** AD25 is asserted when Primary addresses AD[15:11]=01001 2 during a Type 1 to Type 0 conversion. 2164** 08 Varies with External State of PRIVDEV at PCI Bus Reset AD24- IDSEL Disable - When this bit is set, 2165** AD24 is deasserted for any possible Type 1 to Type 0 conversion. 2166** When this bit is clear, 2167** AD24 is asserted when Primary addresses AD[15:11]=01000 2 during a Type 1 to Type 0 conversion. 2168** 07 Varies with External State of PRIVDEV at PCI Bus Reset AD23- IDSEL Disable - When this bit is set, 2169** AD23 is deasserted for any possible Type 1 to Type 0 conversion. 2170** When this bit is clear, 2171** AD23 is asserted when Primary addresses AD[15:11]=00111 2 during a Type 1 to Type 0 conversion. 2172** 06 Varies with External State of PRIVDEV at PCI Bus Reset AD22- IDSEL Disable - When this bit is set, 2173** AD22 is deasserted for any possible Type 1 to Type 0 conversion. 2174** When this bit is clear, 2175** AD22 is asserted when Primary addresses AD[15:11]=00110 2 during a Type 1 to Type 0 conversion. 2176** 05 Varies with External State of PRIVDEV at PCI Bus Reset AD21- IDSEL Disable - When this bit is set, 2177** AD21 is deasserted for any possible Type 1 to Type 0 conversion. 2178** When this bit is clear, 2179** AD21 is asserted when Primary addresses AD[15:11]=00101 2 during a Type 1 to Type 0 conversion. 2180** 04 Varies with External State of PRIVDEV at PCI Bus Reset AD20- IDSEL Disable - When this bit is set, 2181** AD20 is deasserted for any possible Type 1 to Type 0 conversion. 2182** When this bit is clear, 2183** AD20 is asserted when Primary addresses AD[15:11]=00100 2 during a Type 1 to Type 0 conversion. 2184** 03 Varies with External State of PRIVDEV at PCI Bus Reset AD19- IDSEL Disable - When this bit is set, 2185** AD19 is deasserted for any possible Type 1 to Type 0 conversion. 2186** When this bit is clear, 2187** AD19 is asserted when Primary addresses AD[15:11]=00011 2 during a Type 1 to Type 0 conversion. 2188** 02 Varies with External State of PRIVDEV at PCI Bus Reset AD18- IDSEL Disable - When this bit is set, 2189** AD18 is deasserted for any possible Type 1 to Type 0 conversion. 2190** When this bit is clear, 2191** AD18 is asserted when Primary addresses AD[15:11]=00010 2 during a Type 1 to Type 0 conversion. 2192** 01 Varies with External State of PRIVDEV at PCI Bus Reset AD17- IDSEL Disable - When this bit is set, 2193** AD17 is deasserted for any possible Type 1 to Type 0 conversion. 2194** When this bit is clear, 2195** AD17 is asserted when Primary addresses AD[15:11]=00001 2 during a Type 1 to Type 0 conversion. 2196** 00 Varies with External State of PRIVDEV at PCI Bus Reset AD16- IDSEL Disable - When this bit is set, 2197** AD16 is deasserted for any possible Type 1 to Type 0 conversion. 2198** When this bit is clear, 2199** AD16 is asserted when Primary addresses AD[15:11]=00000 2 during a Type 1 to Type 0 conversion. 2200************************************************************************** 2201*/ 2202/* 2203************************************************************************** 2204** Reserved A8-CBh 2205************************************************************************** 2206*/ 2207/* 2208************************************************************************** 2209** PCI Extended Enhanced Capabilities List CC-FFh 2210************************************************************************** 2211** ---------------------------------------------------------------------------------------------------------- 2212** | Byte 3 | Byte 2 | Byte 1 | Byte 0 | Configu-ration Byte Offset 2213** ---------------------------------------------------------------------------------------------------------- 2214** | Power Management Capabilities | Next Item Ptr | Capability ID | DCh 2215** ---------------------------------------------------------------------------------------------------------- 2216** | PM Data | PPB Support | Extensions Power Management CSR | E0h 2217** ---------------------------------------------------------------------------------------------------------- 2218** | Reserved | Reserved | Reserved | E4h 2219** ---------------------------------------------------------------------------------------------------------- 2220** | Reserved | E8h 2221** ---------------------------------------------------------------------------------------------------------- 2222** | Reserved | Reserved | Reserved | Reserved | ECh 2223** ---------------------------------------------------------------------------------------------------------- 2224** | PCI-X Secondary Status | Next Item Ptr | Capability ID | F0h 2225** ---------------------------------------------------------------------------------------------------------- 2226** | PCI-X Bridge Status | F4h 2227** ---------------------------------------------------------------------------------------------------------- 2228** | PCI-X Upstream Split Transaction Control | F8h 2229** ---------------------------------------------------------------------------------------------------------- 2230** | PCI-X Downstream Split Transaction Control | FCh 2231** ---------------------------------------------------------------------------------------------------------- 2232**=============================================================================== 2233** 0xDC: Power Management Capabilities Identifier - PM_CAPID 2234** Bit Default Description 2235** 07:00 01h Identifier (ID): PCI SIG assigned ID for PCI-PM register block 2236**=============================================================================== 2237** 0xDD: Next Item Pointer - PM_NXTP 2238** Bit Default Description 2239** 07:00 F0H Next Capabilities Pointer (PTR): The register defaults to F0H pointing to the PCI-X Extended Capability Header. 2240**=============================================================================== 2241** 0xDF-0xDE: Power Management Capabilities Register - PMCR 2242** Bit Default Description 2243** 15:11 00h PME Supported (PME): PME# cannot be asserted by bridge. 2244** 10 0h State D2 Supported (D2): Indicates no support for state D2. No power management action in this state. 2245** 09 1h State D1 Supported (D1): Indicates support for state D1. No power management action in this state. 2246** 08:06 0h Auxiliary Current (AUXC): This 3 bit field reports the 3.3Vaux auxiliary current requirements for the PCI function. 2247** This returns 000b as PME# wake-up for bridge is not implemented. 2248** 05 0 Special Initialization Required (SINT): Special initialization is not required for bridge. 2249** 04:03 00 Reserved 2250** 02:00 010 Version (VS): Indicates that this supports PCI Bus Power Management Interface Specification, Revision 1.1. 2251**=============================================================================== 2252** 0xE1-0xE0: Power Management Control / Status - Register - PMCSR 2253** Bit Default Description 2254** 15:09 00h Reserved 2255** 08 0b PME_Enable: This bit, when set to 1b enables bridge to assert PME#. 2256** Note that bridge never has occasion to assert PME# and implements this dummy R/W bit only for the purpose of working around an OS PCI-PM bug. 2257** 07:02 00h Reserved 2258** 01:00 00 Power State (PSTATE): This 2-bit field is used both to determine the current power state of 2259** a function and to set the Function into a new power state. 2260** 00 - D0 state 2261** 01 - D1 state 2262** 10 - D2 state 2263** 11 - D3 hot state 2264**=============================================================================== 2265** 0xE2: Power Management Control / Status PCI to PCI Bridge Support - PMCSR_BSE 2266** Bit Default Description 2267** 07 0 Bus Power/Clock Control Enable (BPCC_En): Indicates that the bus power/clock control policies have been disabled. 2268** 06 0 B2/B3 support for D3 Hot (B2_B3#): The state of this bit determines the action that 2269** is to occur as a direct result of programming the function to D3 hot. 2270** This bit is only meaningful when bit 7 (BPCC_En) is a ��1��. 2271** 05:00 00h Reserved 2272**=============================================================================== 2273** 0xE3: Power Management Data Register - PMDR 2274** Bit Default Description 2275** 07:00 00h Reserved 2276**=============================================================================== 2277** 0xF0: PCI-X Capabilities Identifier - PX_CAPID 2278** Bit Default Description 2279** 07:00 07h Identifier (ID): Indicates this is a PCI-X capabilities list. 2280**=============================================================================== 2281** 0xF1: Next Item Pointer - PX_NXTP 2282** Bit Default Description 2283** 07:00 00h Next Item Pointer: Points to the next capability in the linked list The power on default value of this 2284** register is 00h indicating that this is the last entry in the linked list of capabilities. 2285**=============================================================================== 2286** 0xF3-0xF2: PCI-X Secondary Status - PX_SSTS 2287** Bit Default Description 2288** 15:09 00h Reserved 2289** 08:06 Xxx Secondary Clock Frequency (SCF): This field is set with the frequency of the secondary bus. 2290** The values are: 2291** ** BitsMax FrequencyClock Period 2292** ** 000PCI ModeN/A 2293** ** 00166 15 2294** ** 01010010 2295** ** 0111337.5 2296** ** 1xxreservedreserved 2297** ** The default value for this register is the operating frequency of the secondary bus 2298** 05 0b Split Request Delayed. (SRD): This bit is supposed to be set by a bridge when it cannot forward a transaction on the 2299** secondary bus to the primary bus because there is not enough room within the limit 2300** specified in the Split Transaction Commitment Limit field in the Downstream Split 2301** Transaction Control register. The bridge does not set this bit. 2302** 04 0b Split Completion Overrun (SCO): This bit is supposed to be set when a bridge terminates a Split Completion on the ** ** secondary bus with retry or Disconnect at next ADB because its buffers are full. 2303** The bridge does not set this bit. 2304** 03 0b Unexpected Split Completion (USC): This bit is set when an unexpected split completion with a requester ID 2305** equal to bridge secondary bus number, device number 00h, 2306** and function number 0 is received on the secondary interface. 2307** This bit is cleared by software writing a '1'. 2308** 02 0b Split Completion Discarded (SCD): This bit is set 2309** when bridge discards a split completion moving toward the secondary bus 2310** because the requester would not accept it. This bit cleared by software writing a '1'. 2311** 01 1b 133 MHz Capable: Indicates that bridge is capable of running its secondary bus at 133 MHz 2312** 00 1b 64-bit Device (D64): Indicates the width of the secondary bus as 64-bits. 2313**=============================================================================== 2314** 0xF7-0xF6-0xf5-0xF4: PCI-X Bridge Status - PX_BSTS 2315** Bit Default Description 2316** 31:22 0 Reserved 2317** 21 0 Split Request Delayed (SRD): This bit does not be set by bridge. 2318** 20 0 Split Completion Overrun (SCO): This bit does not be set by bridge 2319** because bridge throttles traffic on the completion side. 2320** 19 0 Unexpected Split Completion (USC): The bridge sets this bit to 1b 2321** when it encounters a corrupted Split Completion, possibly with an ** ** inconsistent remaining byte count.Software clears 2322** this bit by writing a 1b to it. 2323** 18 0 Split Completion Discarded (SCD): The bridge sets this bit to 1b 2324** when it has discarded a Split Completion.Software clears this bit by ** ** writing a 1b to it. 2325** 17 1 133 MHz Capable: This bit indicates that the bridge primary interface is ** capable of 133 MHz operation in PCI-X mode. 2326** 0=The maximum operating frequency is 66 MHz. 2327** 1=The maximum operating frequency is 133 MHz. 2328** 16 Varies with the external state of P_32BITPCI# at PCI Bus Reset 64-bit Device (D64): Indicates bus width of the Primary PCI bus interface. 2329** 0=Primary Interface is connected as a 32-bit PCI bus. 2330** 1=Primary Interface is connected as a 64-bit PCI bus. 2331** 15:08 00h Bus Number (BNUM): This field is simply an alias to the PBN field 2332** of the BNUM register at offset 18h. 2333** Apparently it was deemed necessary reflect it here for diagnostic purposes. 2334** 07:03 1fh Device Number (DNUM): Indicates which IDSEL bridge consumes. 2335** May be updated whenever a PCI-X 2336** configuration write cycle that targets bridge scores a hit. 2337** 02:00 0h Function Number (FNUM): The bridge Function # 2338**=============================================================================== 2339** 0xFB-0xFA-0xF9-0xF8: PCI-X Upstream Split Transaction Control - PX_USTC 2340** Bit Default Description 2341** 31:16 003Eh Split Transaction Limit (STL): This register indicates the size of the commitment limit in units of ADQs. 2342** Software is permitted to program this register to any value greater than or equal to 2343** the contents of the Split Transaction Capacity register. A value less than the contents 2344** of the Split Transaction Capacity register causes unspecified results. 2345** A value of 003Eh or greater enables the bridge to forward all Split Requests of any 2346** size regardless of the amount of buffer space available. 2347** 15:00 003Eh Split Transaction Capacity (STC): This read-only field indicates the size of the buffer (number of ADQs) for storing 2348** split completions. This register controls behavior of the bridge buffers for forwarding 2349** Split Transactions from a primary bus requester to a secondary bus completer. 2350** The default value of 003Eh indicates there is available buffer space for 62 ADQs (7936 bytes). 2351**=============================================================================== 2352** 0xFF-0xFE-0xFD-0xFC: PCI-X Downstream Split Transaction Control - PX_DSTC 2353** Bit Default Description 2354** 31:16 003Eh Split Transaction Limit (STL): This register indicates the size of the commitment limit in units of ADQs. 2355** Software is permitted to program this register to any value greater than or equal to 2356** the contents of the Split Transaction Capacity register. A value less than the contents 2357** of the Split Transaction Capacity register causes unspecified results. 2358** A value of 003Eh or greater enables the bridge to forward all Split Requests of any 2359** size regardless of the amount of buffer space available. 2360** 15:00 003Eh Split Transaction Capacity (STC): This read-only field indicates the size of the buffer (number of ADQs) for storing 2361** split completions. This register controls behavior of the bridge buffers for forwarding 2362** Split Transactions from a primary bus requester to a secondary bus completer. 2363** The default value of 003Eh indicates there is available buffer space for 62 ADQs 2364** (7936 bytes). 2365************************************************************************** 2366*/ 2367 2368 2369 2370 2371/* 2372************************************************************************************************************************************* 2373** 80331 Address Translation Unit Register Definitions 2374** ATU Interface Configuration Header Format 2375** The ATU is programmed via a [Type 0] configuration command on the PCI interface. 2376************************************************************************************************************************************* 2377** | Byte 3 | Byte 2 | Byte 1 | Byte 0 | Configuration Byte Offset 2378**=================================================================================================================================== 2379** | ATU Device ID | Vendor ID | 00h 2380** ---------------------------------------------------------------------------------------------------------- 2381** | Status | Command | 04H 2382** ---------------------------------------------------------------------------------------------------------- 2383** | ATU Class Code | Revision ID | 08H 2384** ---------------------------------------------------------------------------------------------------------- 2385** | ATUBISTR | Header Type | Latency Timer | Cacheline Size | 0CH 2386** ---------------------------------------------------------------------------------------------------------- 2387** | Inbound ATU Base Address 0 | 10H 2388** ---------------------------------------------------------------------------------------------------------- 2389** | Inbound ATU Upper Base Address 0 | 14H 2390** ---------------------------------------------------------------------------------------------------------- 2391** | Inbound ATU Base Address 1 | 18H 2392** ---------------------------------------------------------------------------------------------------------- 2393** | Inbound ATU Upper Base Address 1 | 1CH 2394** ---------------------------------------------------------------------------------------------------------- 2395** | Inbound ATU Base Address 2 | 20H 2396** ---------------------------------------------------------------------------------------------------------- 2397** | Inbound ATU Upper Base Address 2 | 24H 2398** ---------------------------------------------------------------------------------------------------------- 2399** | Reserved | 28H 2400** ---------------------------------------------------------------------------------------------------------- 2401** | ATU Subsystem ID | ATU Subsystem Vendor ID | 2CH 2402** ---------------------------------------------------------------------------------------------------------- 2403** | Expansion ROM Base Address | 30H 2404** ---------------------------------------------------------------------------------------------------------- 2405** | Reserved Capabilities Pointer | 34H 2406** ---------------------------------------------------------------------------------------------------------- 2407** | Reserved | 38H 2408** ---------------------------------------------------------------------------------------------------------- 2409** | Maximum Latency | Minimum Grant | Interrupt Pin | Interrupt Line | 3CH 2410** ---------------------------------------------------------------------------------------------------------- 2411********************************************************************************************************************* 2412*/ 2413/* 2414*********************************************************************************** 2415** ATU Vendor ID Register - ATUVID 2416** ----------------------------------------------------------------- 2417** Bit Default Description 2418** 15:00 8086H (0x17D3) ATU Vendor ID - This is a 16-bit value assigned to Intel. 2419** This register, combined with the DID, uniquely identify the PCI device. 2420** Access type is Read/Write to allow the 80331 to configure the register as a different vendor ID 2421** to simulate the interface of a standard mechanism currently used by existing application software. 2422*********************************************************************************** 2423*/ 2424#define ARCMSR_ATU_VENDOR_ID_REG 0x00 /*word*/ 2425/* 2426*********************************************************************************** 2427** ATU Device ID Register - ATUDID 2428** ----------------------------------------------------------------- 2429** Bit Default Description 2430** 15:00 0336H (0x1110) ATU Device ID - This is a 16-bit value assigned to the ATU. 2431** This ID, combined with the VID, uniquely identify any PCI device. 2432*********************************************************************************** 2433*/ 2434#define ARCMSR_ATU_DEVICE_ID_REG 0x02 /*word*/ 2435/* 2436*********************************************************************************** 2437** ATU Command Register - ATUCMD 2438** ----------------------------------------------------------------- 2439** Bit Default Description 2440** 15:11 000000 2 Reserved 2441** 10 0 Interrupt Disable - This bit disables 80331 from asserting the ATU interrupt signal. 2442** 0=enables the assertion of interrupt signal. 2443** 1=disables the assertion of its interrupt signal. 2444** 09 0 2 Fast Back to Back Enable - When cleared, 2445** the ATU interface is not allowed to generate fast back-to-back cycles on its bus. 2446** Ignored when operating in the PCI-X mode. 2447** 08 0 2 SERR# Enable - When cleared, the ATU interface is not allowed to assert SERR# on the PCI interface. 2448** 07 1 2 Address/Data Stepping Control - Address stepping is implemented for configuration transactions. The 2449** ATU inserts 2 clock cycles of address stepping for Conventional Mode and 4 clock cycles 2450** of address stepping for PCI-X mode. 2451** 06 0 2 Parity Error Response - When set, the ATU takes normal action when a parity error 2452** is detected. When cleared, parity checking is disabled. 2453** 05 0 2 VGA Palette Snoop Enable - The ATU interface does not support I/O writes and therefore, 2454** does not perform VGA palette snooping. 2455** 04 0 2 Memory Write and Invalidate Enable - When set, ATU may generate MWI commands. 2456** When clear, ATU use Memory Write commands instead of MWI. Ignored when operating in the PCI-X mode. 2457** 03 0 2 Special Cycle Enable - The ATU interface does not respond to special cycle commands in any way. 2458** Not implemented and a reserved bit field. 2459** 02 0 2 Bus Master Enable - The ATU interface can act as a master on the PCI bus. 2460** When cleared, disables the device from generating PCI accesses. 2461** When set, allows the device to behave as a PCI bus master. 2462** When operating in the PCI-X mode, ATU initiates a split completion transaction regardless 2463** of the state of this bit. 2464** 01 0 2 Memory Enable - Controls the ATU interface��s response to PCI memory addresses. 2465** When cleared, the ATU interface does not respond to any memory access on the PCI bus. 2466** 00 0 2 I/O Space Enable - Controls the ATU interface response to I/O transactions. 2467** Not implemented and a reserved bit field. 2468*********************************************************************************** 2469*/ 2470#define ARCMSR_ATU_COMMAND_REG 0x04 /*word*/ 2471/* 2472*********************************************************************************** 2473** ATU Status Register - ATUSR (Sheet 1 of 2) 2474** ----------------------------------------------------------------- 2475** Bit Default Description 2476** 15 0 2 Detected Parity Error - set when a parity error is detected in data received by the ATU on the PCI bus even 2477** when the ATUCMD register��s Parity Error Response bit is cleared. Set under the following conditions: 2478** �E Write Data Parity Error when the ATU is a target (inbound write). 2479** �E Read Data Parity Error when the ATU is a requester (outbound read). 2480** �E Any Address or Attribute (PCI-X Only) Parity Error on the Bus ** ** ** (including one generated by the ATU). 2481** 14 0 2 SERR# Asserted - set when SERR# is asserted on the PCI bus by the ATU. 2482** 13 0 2 Master Abort - set when a transaction initiated by the ATU PCI master interface, ends in a Master-Abort 2483** or when the ATU receives a Master Abort Split Completion Error Message in PCI-X mode. 2484** 12 0 2 Target Abort (master) - set when a transaction initiated by the ATU PCI master interface, ends in a target 2485** abort or when the ATU receives a Target Abort Split Completion Error Message in PCI-X mode. 2486** 11 0 2 Target Abort (target) - set when the ATU interface, acting as a target, 2487** terminates the transaction on the PCI bus with a target abort. 2488** 10:09 01 2 DEVSEL# Timing - These bits are read-only and define the slowest DEVSEL# 2489** timing for a target device in Conventional PCI Mode regardless of the operating mode 2490** (except configuration accesses). 2491** 00 2=Fast 2492** 01 2=Medium 2493** 10 2=Slow 2494** 11 2=Reserved 2495** The ATU interface uses Medium timing. 2496** 08 0 2 Master Parity Error - The ATU interface sets this bit under the following conditions: 2497** �E The ATU asserted PERR# itself or the ATU observed PERR# asserted. 2498** �E And the ATU acted as the requester 2499** for the operation in which the error occurred. 2500** �E And the ATUCMD register��s Parity Error Response bit is set 2501** �E Or (PCI-X Mode Only) the ATU received a Write Data Parity Error Message 2502** �E And the ATUCMD register��s Parity Error Response bit is set 2503** 07 1 2 (Conventional mode) 2504** 0 2 (PCI-X mode) 2505** Fast Back-to-Back - The ATU/Messaging Unit interface is capable of accepting fast back-to-back 2506** transactions in Conventional PCI mode when the transactions are not to the same target. Since fast 2507** back-to-back transactions do not exist in PCI-X mode, this bit is forced to 0 in the PCI-X mode. 2508** 06 0 2 UDF Supported - User Definable Features are not supported 2509** 05 1 2 66 MHz. Capable - 66 MHz operation is supported. 2510** 04 1 2 Capabilities - When set, this function implements extended capabilities. 2511** 03 0 Interrupt Status - reflects the state of the ATU interrupt 2512** when the Interrupt Disable bit in the command register is a 0. 2513** 0=ATU interrupt signal deasserted. 2514** 1=ATU interrupt signal asserted. 2515** NOTE: Setting the Interrupt Disable bit to a 1 has no effect on the state of this bit. Refer to 2516** Section 3.10.23, ��ATU Interrupt Pin Register - ATUIPR�� on page 236 for details on the ATU 2517** interrupt signal. 2518** 02:00 00000 2 Reserved. 2519*********************************************************************************** 2520*/ 2521#define ARCMSR_ATU_STATUS_REG 0x06 /*word*/ 2522/* 2523*********************************************************************************** 2524** ATU Revision ID Register - ATURID 2525** ----------------------------------------------------------------- 2526** Bit Default Description 2527** 07:00 00H ATU Revision - identifies the 80331 revision number. 2528*********************************************************************************** 2529*/ 2530#define ARCMSR_ATU_REVISION_REG 0x08 /*byte*/ 2531/* 2532*********************************************************************************** 2533** ATU Class Code Register - ATUCCR 2534** ----------------------------------------------------------------- 2535** Bit Default Description 2536** 23:16 05H Base Class - Memory Controller 2537** 15:08 80H Sub Class - Other Memory Controller 2538** 07:00 00H Programming Interface - None defined 2539*********************************************************************************** 2540*/ 2541#define ARCMSR_ATU_CLASS_CODE_REG 0x09 /*3bytes 0x0B,0x0A,0x09*/ 2542/* 2543*********************************************************************************** 2544** ATU Cacheline Size Register - ATUCLSR 2545** ----------------------------------------------------------------- 2546** Bit Default Description 2547** 07:00 00H ATU Cacheline Size - specifies the system cacheline size in DWORDs. Cacheline size is restricted to either 0, 8 or 16 DWORDs. 2548*********************************************************************************** 2549*/ 2550#define ARCMSR_ATU_CACHELINE_SIZE_REG 0x0C /*byte*/ 2551/* 2552*********************************************************************************** 2553** ATU Latency Timer Register - ATULT 2554** ----------------------------------------------------------------- 2555** Bit Default Description 2556** 07:03 00000 2 (for Conventional mode) 2557** 01000 2 (for PCI-X mode) 2558** Programmable Latency Timer - This field varies the latency timer for the interface from 0 to 248 clocks. 2559** The default value is 0 clocks for Conventional PCI mode, and 64 clocks for PCI-X mode. 2560** 02:00 000 2 Latency Timer Granularity - These Bits are read only giving a programmable granularity of 8 clocks for the latency timer. 2561*********************************************************************************** 2562*/ 2563#define ARCMSR_ATU_LATENCY_TIMER_REG 0x0D /*byte*/ 2564/* 2565*********************************************************************************** 2566** ATU Header Type Register - ATUHTR 2567** ----------------------------------------------------------------- 2568** Bit Default Description 2569** 07 0 2 Single Function/Multi-Function Device - Identifies the 80331 as a single-function PCI device. 2570** 06:00 000000 2 PCI Header Type - This bit field indicates the type of PCI header implemented. The ATU interface 2571** header conforms to PCI Local Bus Specification, Revision 2.3. 2572*********************************************************************************** 2573*/ 2574#define ARCMSR_ATU_HEADER_TYPE_REG 0x0E /*byte*/ 2575/* 2576*********************************************************************************** 2577** ATU BIST Register - ATUBISTR 2578** 2579** The ATU BIST Register controls the functions the Intel XScale core performs when BIST is 2580** initiated. This register is the interface between the host processor requesting BIST functions and 2581** the 80331 replying with the results from the software implementation of the BIST functionality. 2582** ----------------------------------------------------------------- 2583** Bit Default Description 2584** 07 0 2 BIST Capable - This bit value is always equal to the ATUCR ATU BIST Interrupt Enable bit. 2585** 06 0 2 Start BIST - When the ATUCR BIST Interrupt Enable bit is set: 2586** Setting this bit generates an interrupt to the Intel XScale core to perform a software BIST function. 2587** The Intel XScale core clears this bit when the BIST software has completed with the BIST results 2588** found in ATUBISTR register bits [3:0]. 2589** When the ATUCR BIST Interrupt Enable bit is clear: 2590** Setting this bit does not generate an interrupt to the Intel XScale core and no BIST functions is performed. 2591** The Intel XScale core does not clear this bit. 2592** 05:04 00 2 Reserved 2593** 03:00 0000 2 BIST Completion Code - when the ATUCR BIST Interrupt Enable bit is set and the ATUBISTR Start BIST bit is set (bit 6): 2594** The Intel XScale core places the results of the software BIST in these bits. 2595** A nonzero value indicates a device-specific error. 2596*********************************************************************************** 2597*/ 2598#define ARCMSR_ATU_BIST_REG 0x0F /*byte*/ 2599 2600/* 2601*************************************************************************************** 2602** ATU Base Registers and Associated Limit Registers 2603*************************************************************************************** 2604** Base Address Register Limit Register Description 2605** Inbound ATU Base Address Register 0 Inbound ATU Limit Register 0 Defines the inbound translation window 0 from the PCI bus. 2606** Inbound ATU Upper Base Address Register 0 N/A Together with ATU Base Address Register 0 defines the inbound ** translation window 0 from the PCI bus for DACs. 2607** Inbound ATU Base Address Register 1 Inbound ATU Limit Register 1 Defines inbound window 1 from the PCI bus. 2608** Inbound ATU Upper Base Address Register 1 N/A Together with ATU Base Address Register 1 defines inbound window ** 1 from the PCI bus for DACs. 2609** Inbound ATU Base Address Register 2 Inbound ATU Limit Register 2 Defines the inbound translation window 2 from the PCI bus. 2610** Inbound ATU Upper Base Address Register 2 N/A Together with ATU Base Address Register 2 defines the inbound ** ** translation window 2 from the PCI bus for DACs. 2611** Inbound ATU Base Address Register 3 Inbound ATU Limit Register 3 Defines the inbound translation window 3 from the PCI bus. 2612** Inbound ATU Upper Base Address Register 3 N/A Together with ATU Base Address Register 3 defines the inbound ** ** translation window 3 from the PCI bus for DACs. 2613** NOTE: This is a private BAR that resides outside of the standard PCI configuration header space (offsets 00H-3FH). 2614** Expansion ROM Base Address Register Expansion ROM Limit Register Defines the window of addresses used by a bus master for reading ** from an Expansion ROM. 2615**-------------------------------------------------------------------------------------- 2616** ATU Inbound Window 1 is not a translate window. 2617** The ATU does not claim any PCI accesses that fall within this range. 2618** This window is used to allocate host memory for use by Private Devices. 2619** When enabled, the ATU interrupts the Intel XScale core when either the IABAR1 register or the IAUBAR1 register is written from the PCI bus. 2620*********************************************************************************** 2621*/ 2622 2623/* 2624*********************************************************************************** 2625** Inbound ATU Base Address Register 0 - IABAR0 2626** 2627** . The Inbound ATU Base Address Register 0 (IABAR0) together with the Inbound ATU Upper Base Address Register 0 (IAUBAR0) 2628** defines the block of memory addresses where the inbound translation window 0 begins. 2629** . The inbound ATU decodes and forwards the bus request to the 80331 internal bus with a translated address to map into 80331 local memory. 2630** . The IABAR0 and IAUBAR0 define the base address and describes the required memory block size. 2631** . Bits 31 through 12 of the IABAR0 is either read/write bits or read only with a value of 0 2632** depending on the value located within the IALR0. 2633** This configuration allows the IABAR0 to be programmed per PCI Local Bus Specification. 2634** The first 4 Kbytes of memory defined by the IABAR0, IAUBAR0 and the IALR0 is reserved for the Messaging Unit. 2635** The programmed value within the base address register must comply with the PCI programming requirements for address alignment. 2636** Warning: 2637** When IALR0 is cleared prior to host configuration: 2638** the user should also clear the Prefetchable Indicator and the Type Indicator. 2639** Assuming IALR0 is not cleared: 2640** a. Since non prefetchable memory windows can never be placed above the 4 Gbyte address boundary, 2641** when the Prefetchable Indicator is cleared prior to host configuration, 2642** the user should also set the Type Indicator for 32 bit addressability. 2643** b. For compliance to the PCI-X Addendum to the PCI Local Bus Specification, 2644** when the Prefetchable Indicator is set prior to host configuration, the user 2645** should also set the Type Indicator for 64 bit addressability. 2646** This is the default for IABAR0. 2647** ----------------------------------------------------------------- 2648** Bit Default Description 2649** 31:12 00000H Translation Base Address 0 - These bits define the actual location 2650** the translation function is to respond to when addressed from the PCI bus. 2651** 11:04 00H Reserved. 2652** 03 1 2 Prefetchable Indicator - When set, defines the memory space as prefetchable. 2653** 02:01 10 2 Type Indicator - Defines the width of the addressability for this memory window: 2654** 00 - Memory Window is locatable anywhere in 32 bit address space 2655** 10 - Memory Window is locatable anywhere in 64 bit address space 2656** 00 0 2 Memory Space Indicator - This bit field describes memory or I/O space base address. 2657** The ATU does not occupy I/O space, 2658** thus this bit must be zero. 2659*********************************************************************************** 2660*/ 2661#define ARCMSR_INBOUND_ATU_BASE_ADDRESS0_REG 0x10 /*dword 0x13,0x12,0x11,0x10*/ 2662#define ARCMSR_INBOUND_ATU_MEMORY_PREFETCHABLE 0x08 2663#define ARCMSR_INBOUND_ATU_MEMORY_WINDOW64 0x04 2664/* 2665*********************************************************************************** 2666** Inbound ATU Upper Base Address Register 0 - IAUBAR0 2667** 2668** This register contains the upper base address when decoding PCI addresses beyond 4 GBytes. 2669** Together with the Translation Base Address this register defines the actual location the translation 2670** function is to respond to when addressed from the PCI bus for addresses > 4GBytes (for DACs). 2671** The programmed value within the base address register must comply with the PCI programming requirements for address alignment. 2672** Note: 2673** When the Type indicator of IABAR0 is set to indicate 32 bit addressability, 2674** the IAUBAR0 register attributes are read-only. 2675** ----------------------------------------------------------------- 2676** Bit Default Description 2677** 31:0 00000H Translation Upper Base Address 0 - Together with the Translation Base Address 0 these bits define the 2678** actual location the translation function is to respond to when addressed from the PCI bus for addresses > 4GBytes. 2679*********************************************************************************** 2680*/ 2681#define ARCMSR_INBOUND_ATU_UPPER_BASE_ADDRESS0_REG 0x14 /*dword 0x17,0x16,0x15,0x14*/ 2682/* 2683*********************************************************************************** 2684** Inbound ATU Base Address Register 1 - IABAR1 2685** 2686** . The Inbound ATU Base Address Register (IABAR1) together with the Inbound ATU Upper Base Address Register 1 (IAUBAR1) 2687** defines the block of memory addresses where the inbound translation window 1 begins. 2688** . This window is used merely to allocate memory on the PCI bus and, the ATU does not process any PCI bus transactions to this memory range. 2689** . The programmed value within the base address register must comply with the PCI programming requirements for address alignment. 2690** . When enabled, the ATU interrupts the Intel XScale core when the IABAR1 register is written from the PCI bus. 2691** Warning: 2692** When a non-zero value is not written to IALR1 prior to host configuration, 2693** the user should not set either the Prefetchable Indicator or the Type Indicator for 64 bit addressability. 2694** This is the default for IABAR1. 2695** Assuming a non-zero value is written to IALR1, 2696** the user may set the Prefetchable Indicator 2697** or the Type Indicator: 2698** a. Since non prefetchable memory windows can never be placed above the 4 Gbyte address 2699** boundary, when the Prefetchable Indicator is not set prior to host configuration, 2700** the user should also leave the Type Indicator set for 32 bit addressability. 2701** This is the default for IABAR1. 2702** b. when the Prefetchable Indicator is set prior to host configuration, 2703** the user should also set the Type Indicator for 64 bit addressability. 2704** ----------------------------------------------------------------- 2705** Bit Default Description 2706** 31:12 00000H Translation Base Address 1 - These bits define the actual location of window 1 on the PCI bus. 2707** 11:04 00H Reserved. 2708** 03 0 2 Prefetchable Indicator - When set, defines the memory space as prefetchable. 2709** 02:01 00 2 Type Indicator - Defines the width of the addressability for this memory window: 2710** 00 - Memory Window is locatable anywhere in 32 bit address space 2711** 10 - Memory Window is locatable anywhere in 64 bit address space 2712** 00 0 2 Memory Space Indicator - This bit field describes memory or I/O space base address. 2713** The ATU does not occupy I/O space, 2714** thus this bit must be zero. 2715*********************************************************************************** 2716*/ 2717#define ARCMSR_INBOUND_ATU_BASE_ADDRESS1_REG 0x18 /*dword 0x1B,0x1A,0x19,0x18*/ 2718/* 2719*********************************************************************************** 2720** Inbound ATU Upper Base Address Register 1 - IAUBAR1 2721** 2722** This register contains the upper base address when locating this window for PCI addresses beyond 4 GBytes. 2723** Together with the IABAR1 this register defines the actual location for this memory window for addresses > 4GBytes (for DACs). 2724** This window is used merely to allocate memory on the PCI bus and, the ATU does not process any PCI bus transactions to this memory range. 2725** The programmed value within the base address register must comply with the PCI programming 2726** requirements for address alignment. 2727** When enabled, the ATU interrupts the Intel XScale core when the IAUBAR1 register is written 2728** from the PCI bus. 2729** Note: 2730** When the Type indicator of IABAR1 is set to indicate 32 bit addressability, 2731** the IAUBAR1 register attributes are read-only. 2732** This is the default for IABAR1. 2733** ----------------------------------------------------------------- 2734** Bit Default Description 2735** 31:0 00000H Translation Upper Base Address 1 - Together with the Translation Base Address 1 2736** these bits define the actual location for this memory window on the PCI bus for addresses > 4GBytes. 2737*********************************************************************************** 2738*/ 2739#define ARCMSR_INBOUND_ATU_UPPER_BASE_ADDRESS1_REG 0x1C /*dword 0x1F,0x1E,0x1D,0x1C*/ 2740/* 2741*********************************************************************************** 2742** Inbound ATU Base Address Register 2 - IABAR2 2743** 2744** . The Inbound ATU Base Address Register 2 (IABAR2) together with the Inbound ATU Upper Base Address Register 2 (IAUBAR2) 2745** defines the block of memory addresses where the inbound translation window 2 begins. 2746** . The inbound ATU decodes and forwards the bus request to the 80331 internal bus with a translated address to map into 80331 local memory. 2747** . The IABAR2 and IAUBAR2 define the base address and describes the required memory block size 2748** . Bits 31 through 12 of the IABAR2 is either read/write bits or read only with a value of 0 depending on the value located within the IALR2. 2749** The programmed value within the base address register must comply with the PCI programming requirements for address alignment. 2750** Warning: 2751** When a non-zero value is not written to IALR2 prior to host configuration, 2752** the user should not set either the Prefetchable Indicator 2753** or the Type Indicator for 64 bit addressability. 2754** This is the default for IABAR2. 2755** Assuming a non-zero value is written to IALR2, 2756** the user may set the Prefetchable Indicator 2757** or the Type Indicator: 2758** a. Since non prefetchable memory windows can never be placed above the 4 Gbyte address boundary, 2759** when the Prefetchable Indicator is not set prior to host configuration, 2760** the user should also leave the Type Indicator set for 32 bit addressability. 2761** This is the default for IABAR2. 2762** b. when the Prefetchable Indicator is set prior to host configuration, 2763** the user should also set the Type Indicator for 64 bit addressability. 2764** ----------------------------------------------------------------- 2765** Bit Default Description 2766** 31:12 00000H Translation Base Address 2 - These bits define the actual location 2767** the translation function is to respond to when addressed from the PCI bus. 2768** 11:04 00H Reserved. 2769** 03 0 2 Prefetchable Indicator - When set, defines the memory space as prefetchable. 2770** 02:01 00 2 Type Indicator - Defines the width of the addressability for this memory window: 2771** 00 - Memory Window is locatable anywhere in 32 bit address space 2772** 10 - Memory Window is locatable anywhere in 64 bit address space 2773** 00 0 2 Memory Space Indicator - This bit field describes memory or I/O space base address. 2774** The ATU does not occupy I/O space, 2775** thus this bit must be zero. 2776*********************************************************************************** 2777*/ 2778#define ARCMSR_INBOUND_ATU_BASE_ADDRESS2_REG 0x20 /*dword 0x23,0x22,0x21,0x20*/ 2779/* 2780*********************************************************************************** 2781** Inbound ATU Upper Base Address Register 2 - IAUBAR2 2782** 2783** This register contains the upper base address when decoding PCI addresses beyond 4 GBytes. 2784** Together with the Translation Base Address this register defines the actual location 2785** the translation function is to respond to when addressed from the PCI bus for addresses > 4GBytes (for DACs). 2786** The programmed value within the base address register must comply with the PCI programming 2787** requirements for address alignment. 2788** Note: 2789** When the Type indicator of IABAR2 is set to indicate 32 bit addressability, 2790** the IAUBAR2 register attributes are read-only. 2791** This is the default for IABAR2. 2792** ----------------------------------------------------------------- 2793** Bit Default Description 2794** 31:0 00000H Translation Upper Base Address 2 - Together with the Translation Base Address 2 2795** these bits define the actual location the translation function is to respond to 2796** when addressed from the PCI bus for addresses > 4GBytes. 2797*********************************************************************************** 2798*/ 2799#define ARCMSR_INBOUND_ATU_UPPER_BASE_ADDRESS2_REG 0x24 /*dword 0x27,0x26,0x25,0x24*/ 2800/* 2801*********************************************************************************** 2802** ATU Subsystem Vendor ID Register - ASVIR 2803** ----------------------------------------------------------------- 2804** Bit Default Description 2805** 15:0 0000H Subsystem Vendor ID - This register uniquely identifies the add-in board or subsystem vendor. 2806*********************************************************************************** 2807*/ 2808#define ARCMSR_ATU_SUBSYSTEM_VENDOR_ID_REG 0x2C /*word 0x2D,0x2C*/ 2809/* 2810*********************************************************************************** 2811** ATU Subsystem ID Register - ASIR 2812** ----------------------------------------------------------------- 2813** Bit Default Description 2814** 15:0 0000H Subsystem ID - uniquely identifies the add-in board or subsystem. 2815*********************************************************************************** 2816*/ 2817#define ARCMSR_ATU_SUBSYSTEM_ID_REG 0x2E /*word 0x2F,0x2E*/ 2818/* 2819*********************************************************************************** 2820** Expansion ROM Base Address Register -ERBAR 2821** ----------------------------------------------------------------- 2822** Bit Default Description 2823** 31:12 00000H Expansion ROM Base Address - These bits define the actual location 2824** where the Expansion ROM address window resides when addressed from the PCI bus on any 4 Kbyte boundary. 2825** 11:01 000H Reserved 2826** 00 0 2 Address Decode Enable - This bit field shows the ROM address 2827** decoder is enabled or disabled. When cleared, indicates the address decoder is disabled. 2828*********************************************************************************** 2829*/ 2830#define ARCMSR_EXPANSION_ROM_BASE_ADDRESS_REG 0x30 /*dword 0x33,0x32,0v31,0x30*/ 2831#define ARCMSR_EXPANSION_ROM_ADDRESS_DECODE_ENABLE 0x01 2832/* 2833*********************************************************************************** 2834** ATU Capabilities Pointer Register - ATU_CAP_PTR 2835** ----------------------------------------------------------------- 2836** Bit Default Description 2837** 07:00 C0H Capability List Pointer - This provides an offset in this function��s configuration space 2838** that points to the 80331 PCl Bus Power Management extended capability. 2839*********************************************************************************** 2840*/ 2841#define ARCMSR_ATU_CAPABILITY_PTR_REG 0x34 /*byte*/ 2842/* 2843*********************************************************************************** 2844** Determining Block Sizes for Base Address Registers 2845** The required address size and type can be determined by writing ones to a base address register and 2846** reading from the registers. By scanning the returned value from the least-significant bit of the base 2847** address registers upwards, the programmer can determine the required address space size. The 2848** binary-weighted value of the first non-zero bit found indicates the required amount of space. 2849** Table 105 describes the relationship between the values read back and the byte sizes the base 2850** address register requires. 2851** As an example, assume that FFFF.FFFFH is written to the ATU Inbound Base Address Register 0 2852** (IABAR0) and the value read back is FFF0.0008H. Bit zero is a zero, so the device requires 2853** memory address space. Bit three is one, so the memory does supports prefetching. Scanning 2854** upwards starting at bit four, bit twenty is the first one bit found. The binary-weighted value of this 2855** bit is 1,048,576, indicated that the device requires 1 Mbyte of memory space. 2856** The ATU Base Address Registers and the Expansion ROM Base Address Register use their 2857** associated limit registers to enable which bits within the base address register are read/write and 2858** which bits are read only (0). This allows the programming of these registers in a manner similar to 2859** other PCI devices even though the limit is variable. 2860** Table 105. Memory Block Size Read Response 2861** Response After Writing all 1s 2862** to the Base Address Register 2863** Size 2864** (Bytes) 2865** Response After Writing all 1s 2866** to the Base Address Register 2867** Size 2868** (Bytes) 2869** FFFFFFF0H 16 FFF00000H 1 M 2870** FFFFFFE0H 32 FFE00000H 2 M 2871** FFFFFFC0H 64 FFC00000H 4 M 2872** FFFFFF80H 128 FF800000H 8 M 2873** FFFFFF00H 256 FF000000H 16 M 2874** FFFFFE00H 512 FE000000H 32 M 2875** FFFFFC00H 1K FC000000H 64 M 2876** FFFFF800H 2K F8000000H 128 M 2877** FFFFF000H 4K F0000000H 256 M 2878** FFFFE000H 8K E0000000H 512 M 2879** FFFFC000H 16K C0000000H 1 G 2880** FFFF8000H 32K 80000000H 2 G 2881** FFFF0000H 64K 2882** 00000000H 2883** Register not 2884** imple-mented, 2885** no 2886** address 2887** space 2888** required. 2889** FFFE0000H 128K 2890** FFFC0000H 256K 2891** FFF80000H 512K 2892** 2893*************************************************************************************** 2894*/ 2895 2896 2897 2898/* 2899*********************************************************************************** 2900** ATU Interrupt Line Register - ATUILR 2901** ----------------------------------------------------------------- 2902** Bit Default Description 2903** 07:00 FFH Interrupt Assigned - system-assigned value identifies which system interrupt controller��s interrupt 2904** request line connects to the device's PCI interrupt request lines 2905** (as specified in the interrupt pin register). 2906** A value of FFH signifies ��no connection�� or ��unknown��. 2907*********************************************************************************** 2908*/ 2909#define ARCMSR_ATU_INTERRUPT_LINE_REG 0x3C /*byte*/ 2910/* 2911*********************************************************************************** 2912** ATU Interrupt Pin Register - ATUIPR 2913** ----------------------------------------------------------------- 2914** Bit Default Description 2915** 07:00 01H Interrupt Used - A value of 01H signifies that the ATU interface unit uses INTA# as the interrupt pin. 2916*********************************************************************************** 2917*/ 2918#define ARCMSR_ATU_INTERRUPT_PIN_REG 0x3D /*byte*/ 2919/* 2920*********************************************************************************** 2921** ATU Minimum Grant Register - ATUMGNT 2922** ----------------------------------------------------------------- 2923** Bit Default Description 2924** 07:00 80H This register specifies how long a burst period the device needs in increments of 8 PCI clocks. 2925*********************************************************************************** 2926*/ 2927#define ARCMSR_ATU_MINIMUM_GRANT_REG 0x3E /*byte*/ 2928/* 2929*********************************************************************************** 2930** ATU Maximum Latency Register - ATUMLAT 2931** ----------------------------------------------------------------- 2932** Bit Default Description 2933** 07:00 00H Specifies frequency (how often) the device needs to access the PCI bus 2934** in increments of 8 PCI clocks. A zero value indicates the device has no stringent requirement. 2935*********************************************************************************** 2936*/ 2937#define ARCMSR_ATU_MAXIMUM_LATENCY_REG 0x3F /*byte*/ 2938/* 2939*********************************************************************************** 2940** Inbound Address Translation 2941** 2942** The ATU allows external PCI bus initiators to directly access the internal bus. 2943** These PCI bus initiators can read or write 80331 memory-mapped registers or 80331 local memory space. 2944** The process of inbound address translation involves two steps: 2945** 1. Address Detection. 2946** �E Determine when the 32-bit PCI address (64-bit PCI address during DACs) is 2947** within the address windows defined for the inbound ATU. 2948** �E Claim the PCI transaction with medium DEVSEL# timing in the conventional PCI 2949** mode and with Decode A DEVSEL# timing in the PCI-X mode. 2950** 2. Address Translation. 2951** �E Translate the 32-bit PCI address (lower 32-bit PCI address during DACs) to a 32-bit 80331 internal bus address. 2952** The ATU uses the following registers in inbound address window 0 translation: 2953** �E Inbound ATU Base Address Register 0 2954** �E Inbound ATU Limit Register 0 2955** �E Inbound ATU Translate Value Register 0 2956** The ATU uses the following registers in inbound address window 2 translation: 2957** �E Inbound ATU Base Address Register 2 2958** �E Inbound ATU Limit Register 2 2959** �E Inbound ATU Translate Value Register 2 2960** The ATU uses the following registers in inbound address window 3 translation: 2961** �E Inbound ATU Base Address Register 3 2962** �E Inbound ATU Limit Register 3 2963** �E Inbound ATU Translate Value Register 3 2964** Note: Inbound Address window 1 is not a translate window. 2965** Instead, window 1 may be used to allocate host memory for Private Devices. 2966** Inbound Address window 3 does not reside in the standard section of the configuration header (offsets 00H - 3CH), 2967** thus the host BIOS does not configure window 3. 2968** Window 3 is intended to be used as a special window into local memory for private PCI 2969** agents controlled by the 80331 in conjunction with the Private Memory Space of the bridge. 2970** PCI-to-PCI Bridge in 80331 or 2971** Inbound address detection is determined from the 32-bit PCI address, 2972** (64-bit PCI address during DACs) the base address register and the limit register. 2973** In the case of DACs none of the upper 32-bits of the address is masked during address comparison. 2974** 2975** The algorithm for detection is: 2976** 2977** Equation 1. Inbound Address Detection 2978** When (PCI_Address [31:0] & Limit_Register[31:0]) == (Base_Register[31:0] & PCI_Address [63:32]) == Base_Register[63:32] (for DACs only) 2979** the PCI Address is claimed by the Inbound ATU. 2980** 2981** The incoming 32-bit PCI address (lower 32-bits of the address in case of DACs) is bitwise ANDed 2982** with the associated inbound limit register. 2983** When the result matches the base register (and upper base address matches upper PCI address in case of DACs), 2984** the inbound PCI address is detected as being within the inbound translation window and is claimed by the ATU. 2985** 2986** Note: The first 4 Kbytes of the ATU inbound address translation window 0 are reserved for the Messaging Unit. 2987** Once the transaction is claimed, the address must be translated from a PCI address to a 32-bit 2988** internal bus address. In case of DACs upper 32-bits of the address is simply discarded and only the 2989** lower 32-bits are used during address translation. 2990** The algorithm is: 2991** 2992** 2993** Equation 2. Inbound Translation 2994** Intel I/O processor Internal Bus Address=(PCI_Address[31:0] & ~Limit_Register[31:0]) | ATU_Translate_Value_Register[31:0]. 2995** 2996** The incoming 32-bit PCI address (lower 32-bits in case of DACs) is first bitwise ANDed with the 2997** bitwise inverse of the limit register. This result is bitwise ORed with the ATU Translate Value and 2998** the result is the internal bus address. This translation mechanism is used for all inbound memory 2999** read and write commands excluding inbound configuration read and writes. 3000** In the PCI mode for inbound memory transactions, the only burst order supported is Linear 3001** Incrementing. For any other burst order, the ATU signals a Disconnect after the first data phase. 3002** The PCI-X supports linear incrementing only, and hence above situation is not encountered in the PCI-X mode. 3003** example: 3004** Register Values 3005** Base_Register=3A00 0000H 3006** Limit_Register=FF80 0000H (8 Mbyte limit value) 3007** Value_Register=B100 0000H 3008** Inbound Translation Window ranges from 3A00 0000H to 3A7F FFFFH (8 Mbytes) 3009** 3010** Address Detection (32-bit address) 3011** 3012** PCI_Address & Limit_Register == Base_Register 3013** 3A45 012CH & FF80 0000H == 3A00 0000H 3014** 3015** ANS: PCI_Address is in the Inbound Translation Window 3016** Address Translation (to get internal bus address) 3017** 3018** IB_Address=(PCI_Address & ~Limit_Register) | Value_Reg 3019** IB_Address=(3A45 012CH & 007F FFFFH) | B100 0000H 3020** 3021** ANS:IB_Address=B145 012CH 3022*********************************************************************************** 3023*/ 3024 3025 3026 3027/* 3028*********************************************************************************** 3029** Inbound ATU Limit Register 0 - IALR0 3030** 3031** Inbound address translation for memory window 0 occurs for data transfers occurring from the PCI 3032** bus (originated from the PCI bus) to the 80331 internal bus. The address translation block converts 3033** PCI addresses to internal bus addresses. 3034** The 80331 translate value register��s programmed value must be naturally aligned with the base 3035** address register��s programmed value. The limit register is used as a mask; thus, the lower address 3036** bits programmed into the 80331 translate value register are invalid. Refer to the PCI Local Bus 3037** Specification, Revision 2.3 for additional information on programming base address registers. 3038** Bits 31 to 12 within the IALR0 have a direct effect on the IABAR0 register, bits 31 to 12, with a 3039** one to one correspondence. A value of 0 in a bit within the IALR0 makes the corresponding bit 3040** within the IABAR0 a read only bit which always returns 0. A value of 1 in a bit within the IALR0 3041** makes the corresponding bit within the IABAR0 read/write from PCI. Note that a consequence of 3042** this programming scheme is that unless a valid value exists within the IALR0, all writes to the 3043** IABAR0 has no effect since a value of all zeros within the IALR0 makes the IABAR0 a read only register. 3044** ----------------------------------------------------------------- 3045** Bit Default Description 3046** 31:12 FF000H Inbound Translation Limit 0 - This readback value determines the memory block size required for 3047** inbound memory window 0 of the address translation unit. This defaults to an inbound window of 16MB. 3048** 11:00 000H Reserved 3049*********************************************************************************** 3050*/ 3051#define ARCMSR_INBOUND_ATU_LIMIT0_REG 0x40 /*dword 0x43,0x42,0x41,0x40*/ 3052/* 3053*********************************************************************************** 3054** Inbound ATU Translate Value Register 0 - IATVR0 3055** 3056** The Inbound ATU Translate Value Register 0 (IATVR0) contains the internal bus address used to 3057** convert PCI bus addresses. The converted address is driven on the internal bus as a result of the 3058** inbound ATU address translation. 3059** ----------------------------------------------------------------- 3060** Bit Default Description 3061** 31:12 FF000H Inbound ATU Translation Value 0 - This value is used to convert the PCI address to internal bus addresses. 3062** This value must be 64-bit aligned on the internal bus. 3063** The default address allows the ATU to access the internal 80331 memory-mapped registers. 3064** 11:00 000H Reserved 3065*********************************************************************************** 3066*/ 3067#define ARCMSR_INBOUND_ATU_TRANSLATE_VALUE0_REG 0x44 /*dword 0x47,0x46,0x45,0x44*/ 3068/* 3069*********************************************************************************** 3070** Expansion ROM Limit Register - ERLR 3071** 3072** The Expansion ROM Limit Register (ERLR) defines the block size of addresses the ATU defines 3073** as Expansion ROM address space. The block size is programmed by writing a value into the ERLR. 3074** Bits 31 to 12 within the ERLR have a direct effect on the ERBAR register, bits 31 to 12, with a one 3075** to one correspondence. A value of 0 in a bit within the ERLR makes the corresponding bit within 3076** the ERBAR a read only bit which always returns 0. A value of 1 in a bit within the ERLR makes 3077** the corresponding bit within the ERBAR read/write from PCI. 3078** ----------------------------------------------------------------- 3079** Bit Default Description 3080** 31:12 000000H Expansion ROM Limit - Block size of memory required for the Expansion ROM translation unit. Default 3081** value is 0, which indicates no Expansion ROM address space and all bits within the ERBAR are read only with a value of 0. 3082** 11:00 000H Reserved. 3083*********************************************************************************** 3084*/ 3085#define ARCMSR_EXPANSION_ROM_LIMIT_REG 0x48 /*dword 0x4B,0x4A,0x49,0x48*/ 3086/* 3087*********************************************************************************** 3088** Expansion ROM Translate Value Register - ERTVR 3089** 3090** The Expansion ROM Translate Value Register contains the 80331 internal bus address which the 3091** ATU converts the PCI bus access. This address is driven on the internal bus as a result of the 3092** Expansion ROM address translation. 3093** ----------------------------------------------------------------- 3094** Bit Default Description 3095** 31:12 00000H Expansion ROM Translation Value - Used to convert PCI addresses to 80331 internal bus addresses 3096** for Expansion ROM accesses. The Expansion ROM address translation value must be word aligned on the internal bus. 3097** 11:00 000H Reserved 3098*********************************************************************************** 3099*/ 3100#define ARCMSR_EXPANSION_ROM_TRANSLATE_VALUE_REG 0x4C /*dword 0x4F,0x4E,0x4D,0x4C*/ 3101/* 3102*********************************************************************************** 3103** Inbound ATU Limit Register 1 - IALR1 3104** 3105** Bits 31 to 12 within the IALR1 have a direct effect on the IABAR1 register, bits 31 to 12, with a 3106** one to one correspondence. A value of 0 in a bit within the IALR1 makes the corresponding bit 3107** within the IABAR1 a read only bit which always returns 0. A value of 1 in a bit within the IALR1 3108** makes the corresponding bit within the IABAR1 read/write from PCI. Note that a consequence of 3109** this programming scheme is that unless a valid value exists within the IALR1, all writes to the 3110** IABAR1 has no effect since a value of all zeros within the IALR1 makes the IABAR1 a read only 3111** register. 3112** The inbound memory window 1 is used merely to allocate memory on the PCI bus. The ATU does 3113** not process any PCI bus transactions to this memory range. 3114** Warning: The ATU does not claim any PCI accesses that fall within the range defined by IABAR1, 3115** IAUBAR1, and IALR1. 3116** ----------------------------------------------------------------- 3117** Bit Default Description 3118** 31:12 00000H Inbound Translation Limit 1 - This readback value determines the memory block size 3119** required for the ATUs memory window 1. 3120** 11:00 000H Reserved 3121*********************************************************************************** 3122*/ 3123#define ARCMSR_INBOUND_ATU_LIMIT1_REG 0x50 /*dword 0x53,0x52,0x51,0x50*/ 3124/* 3125*********************************************************************************** 3126** Inbound ATU Limit Register 2 - IALR2 3127** 3128** Inbound address translation for memory window 2 occurs for data transfers occurring from the PCI 3129** bus (originated from the PCI bus) to the 80331 internal bus. The address translation block converts 3130** PCI addresses to internal bus addresses. 3131** The inbound translation base address for inbound window 2 is specified in Section 3.10.15. When 3132** determining block size requirements �X as described in Section 3.10.21 �X the translation limit 3133** register provides the block size requirements for the base address register. The remaining registers 3134** used for performing address translation are discussed in Section 3.2.1.1. 3135** The 80331 translate value register��s programmed value must be naturally aligned with the base 3136** address register��s programmed value. The limit register is used as a mask; thus, the lower address 3137** bits programmed into the 80331 translate value register are invalid. Refer to the PCI Local Bus 3138** Specification, Revision 2.3 for additional information on programming base address registers. 3139** Bits 31 to 12 within the IALR2 have a direct effect on the IABAR2 register, bits 31 to 12, with a 3140** one to one correspondence. A value of 0 in a bit within the IALR2 makes the corresponding bit 3141** within the IABAR2 a read only bit which always returns 0. A value of 1 in a bit within the IALR2 3142** makes the corresponding bit within the IABAR2 read/write from PCI. Note that a consequence of 3143** this programming scheme is that unless a valid value exists within the IALR2, all writes to the 3144** IABAR2 has no effect since a value of all zeros within the IALR2 makes the IABAR2 a read only 3145** register. 3146** ----------------------------------------------------------------- 3147** Bit Default Description 3148** 31:12 00000H Inbound Translation Limit 2 - This readback value determines the memory block size 3149** required for the ATUs memory window 2. 3150** 11:00 000H Reserved 3151*********************************************************************************** 3152*/ 3153#define ARCMSR_INBOUND_ATU_LIMIT2_REG 0x54 /*dword 0x57,0x56,0x55,0x54*/ 3154/* 3155*********************************************************************************** 3156** Inbound ATU Translate Value Register 2 - IATVR2 3157** 3158** The Inbound ATU Translate Value Register 2 (IATVR2) contains the internal bus address used to 3159** convert PCI bus addresses. The converted address is driven on the internal bus as a result of the 3160** inbound ATU address translation. 3161** ----------------------------------------------------------------- 3162** Bit Default Description 3163** 31:12 00000H Inbound ATU Translation Value 2 - This value is used to convert the PCI address to internal bus addresses. 3164** This value must be 64-bit aligned on the internal bus. 3165** The default address allows the ATU to access the internal 80331 ** ** memory-mapped registers. 3166** 11:00 000H Reserved 3167*********************************************************************************** 3168*/ 3169#define ARCMSR_INBOUND_ATU_TRANSLATE_VALUE2_REG 0x58 /*dword 0x5B,0x5A,0x59,0x58*/ 3170/* 3171*********************************************************************************** 3172** Outbound I/O Window Translate Value Register - OIOWTVR 3173** 3174** The Outbound I/O Window Translate Value Register (OIOWTVR) contains the PCI I/O address 3175** used to convert the internal bus access to a PCI address. This address is driven on the PCI bus as a 3176** result of the outbound ATU address translation. 3177** The I/O window is from 80331 internal bus address 9000 000H to 9000 FFFFH with the fixed 3178** length of 64 Kbytes. 3179** ----------------------------------------------------------------- 3180** Bit Default Description 3181** 31:16 0000H Outbound I/O Window Translate Value - Used to convert internal bus addresses to PCI addresses. 3182** 15:00 0000H Reserved 3183*********************************************************************************** 3184*/ 3185#define ARCMSR_OUTBOUND_IO_WINDOW_TRANSLATE_VALUE_REG 0x5C /*dword 0x5F,0x5E,0x5D,0x5C*/ 3186/* 3187*********************************************************************************** 3188** Outbound Memory Window Translate Value Register 0 -OMWTVR0 3189** 3190** The Outbound Memory Window Translate Value Register 0 (OMWTVR0) contains the PCI 3191** address used to convert 80331 internal bus addresses for outbound transactions. This address is 3192** driven on the PCI bus as a result of the outbound ATU address translation. 3193** The memory window is from internal bus address 8000 000H to 83FF FFFFH with the fixed length 3194** of 64 Mbytes. 3195** ----------------------------------------------------------------- 3196** Bit Default Description 3197** 31:26 00H Outbound MW Translate Value - Used to convert 80331 internal bus addresses to PCI addresses. 3198** 25:02 00 0000H Reserved 3199** 01:00 00 2 Burst Order - This bit field shows the address sequence during a memory burst. 3200** Only linear incrementing mode is supported. 3201*********************************************************************************** 3202*/ 3203#define ARCMSR_OUTBOUND_MEMORY_WINDOW_TRANSLATE_VALUE0_REG 0x60 /*dword 0x63,0x62,0x61,0x60*/ 3204/* 3205*********************************************************************************** 3206** Outbound Upper 32-bit Memory Window Translate Value Register 0 - OUMWTVR0 3207** 3208** The Outbound Upper 32-bit Memory Window Translate Value Register 0 (OUMWTVR0) defines 3209** the upper 32-bits of address used during a dual address cycle. This enables the outbound ATU to 3210** directly address anywhere within the 64-bit host address space. When this register is all-zero, then 3211** a SAC is generated on the PCI bus. 3212** The memory window is from internal bus address 8000 000H to 83FF FFFFH with the fixed 3213** length of 64 Mbytes. 3214** ----------------------------------------------------------------- 3215** Bit Default Description 3216** 31:00 0000 0000H These bits define the upper 32-bits of address driven during the dual address cycle (DAC). 3217*********************************************************************************** 3218*/ 3219#define ARCMSR_OUTBOUND_UPPER32_MEMORY_WINDOW_TRANSLATE_VALUE0_REG 0x64 /*dword 0x67,0x66,0x65,0x64*/ 3220/* 3221*********************************************************************************** 3222** Outbound Memory Window Translate Value Register 1 -OMWTVR1 3223** 3224** The Outbound Memory Window Translate Value Register 1 (OMWTVR1) contains the PCI 3225** address used to convert 80331 internal bus addresses for outbound transactions. This address is 3226** driven on the PCI bus as a result of the outbound ATU address translation. 3227** The memory window is from internal bus address 8400 000H to 87FF FFFFH with the fixed length 3228** of 64 Mbytes. 3229** ----------------------------------------------------------------- 3230** Bit Default Description 3231** 31:26 00H Outbound MW Translate Value - Used to convert 80331 internal bus addresses to PCI addresses. 3232** 25:02 00 0000H Reserved 3233** 01:00 00 2 Burst Order - This bit field shows the address sequence during a memory burst. 3234** Only linear incrementing mode is supported. 3235*********************************************************************************** 3236*/ 3237#define ARCMSR_OUTBOUND_MEMORY_WINDOW_TRANSLATE_VALUE1_REG 0x68 /*dword 0x6B,0x6A,0x69,0x68*/ 3238/* 3239*********************************************************************************** 3240** Outbound Upper 32-bit Memory Window Translate Value Register 1 - OUMWTVR1 3241** 3242** The Outbound Upper 32-bit Memory Window Translate Value Register 1 (OUMWTVR1) defines 3243** the upper 32-bits of address used during a dual address cycle. This enables the outbound ATU to 3244** directly address anywhere within the 64-bit host address space. When this register is all-zero, then 3245** a SAC is generated on the PCI bus. 3246** The memory window is from internal bus address 8400 000H to 87FF FFFFH with the fixed length 3247** of 64 Mbytes. 3248** ----------------------------------------------------------------- 3249** Bit Default Description 3250** 31:00 0000 0000H These bits define the upper 32-bits of address driven during the dual address cycle (DAC). 3251*********************************************************************************** 3252*/ 3253#define ARCMSR_OUTBOUND_UPPER32_MEMORY_WINDOW_TRANSLATE_VALUE1_REG 0x6C /*dword 0x6F,0x6E,0x6D,0x6C*/ 3254/* 3255*********************************************************************************** 3256** Outbound Upper 32-bit Direct Window Translate Value Register - OUDWTVR 3257** 3258** The Outbound Upper 32-bit Direct Window Translate Value Register (OUDWTVR) defines the 3259** upper 32-bits of address used during a dual address cycle for the transactions via Direct Addressing 3260** Window. This enables the outbound ATU to directly address anywhere within the 64-bit host 3261** address space. When this register is all-zero, then a SAC is generated on the PCI bus. 3262** ----------------------------------------------------------------- 3263** Bit Default Description 3264** 31:00 0000 0000H These bits define the upper 32-bits of address driven during the dual address cycle (DAC). 3265*********************************************************************************** 3266*/ 3267#define ARCMSR_OUTBOUND_UPPER32_DIRECT_WINDOW_TRANSLATE_VALUE_REG 0x78 /*dword 0x7B,0x7A,0x79,0x78*/ 3268/* 3269*********************************************************************************** 3270** ATU Configuration Register - ATUCR 3271** 3272** The ATU Configuration Register controls the outbound address translation for address translation 3273** unit. It also contains bits for Conventional PCI Delayed Read Command (DRC) aliasing, discard 3274** timer status, SERR# manual assertion, SERR# detection interrupt masking, and ATU BIST 3275** interrupt enabling. 3276** ----------------------------------------------------------------- 3277** Bit Default Description 3278** 31:20 00H Reserved 3279** 19 0 2 ATU DRC Alias - when set, the ATU does not distinguish read commands when attempting to match a 3280** current PCI read transaction with read data enqueued within the DRC buffer. When clear, a current read 3281** transaction must have the exact same read command as the DRR for the ATU to deliver DRC data. Not 3282** applicable in the PCI-X mode. 3283** 18 0 2 Direct Addressing Upper 2Gbytes Translation Enable - When set, 3284** with Direct Addressing enabled (bit 7 of the ATUCR set), 3285** the ATU forwards internal bus cycles with an address between 0000.0040H and 3286** 7FFF.FFFFH to the PCI bus with bit 31 of the address set (8000.0000H - FFFF.FFFFH). 3287** When clear, no translation occurs. 3288** 17 0 2 Reserved 3289** 16 0 2 SERR# Manual Assertion - when set, the ATU asserts SERR# for one clock on the PCI interface. Until 3290** cleared, SERR# may not be manually asserted again. Once cleared, operation proceeds as specified. 3291** 15 0 2 ATU Discard Timer Status - when set, one of the 4 discard timers within the ATU has expired and 3292** discarded the delayed completion transaction within the queue. When clear, no timer has expired. 3293** 14:10 00000 2 Reserved 3294** 09 0 2 SERR# Detected Interrupt Enable - When set, the Intel XScale core is signalled an HPI# interrupt 3295** when the ATU detects that SERR# was asserted. When clear, 3296** the Intel XScale core is not interrupted when SERR# is detected. 3297** 08 0 2 Direct Addressing Enable - Setting this bit enables direct outbound addressing through the ATU. 3298** Internal bus cycles with an address between 0000.0040H and 7FFF.FFFFH automatically forwards to 3299** the PCI bus with or without translation of address bit 31 based on the setting of bit 18 of 3300** the ATUCR. 3301** 07:04 0000 2 Reserved 3302** 03 0 2 ATU BIST Interrupt Enable - When set, enables an interrupt to the Intel XScale core when the start 3303** BIST bit is set in the ATUBISTR register. This bit is also reflected as the BIST Capable bit 7 3304** in the ATUBISTR register. 3305** 02 0 2 Reserved 3306** 01 0 2 Outbound ATU Enable - When set, enables the outbound address translation unit. 3307** When cleared, disables the outbound ATU. 3308** 00 0 2 Reserved 3309*********************************************************************************** 3310*/ 3311#define ARCMSR_ATU_CONFIGURATION_REG 0x80 /*dword 0x83,0x82,0x81,0x80*/ 3312/* 3313*********************************************************************************** 3314** PCI Configuration and Status Register - PCSR 3315** 3316** The PCI Configuration and Status Register has additional bits for controlling and monitoring 3317** various features of the PCI bus interface. 3318** ----------------------------------------------------------------- 3319** Bit Default Description 3320** 31:19 0000H Reserved 3321** 18 0 2 Detected Address or Attribute Parity Error - set when a parity error is detected during either the address 3322** or attribute phase of a transaction on the PCI bus even when the ATUCMD register Parity Error 3323** Response bit is cleared. Set under the following conditions: 3324** �E Any Address or Attribute (PCI-X Only) Parity Error on the Bus (including one generated by the ATU). 3325** 17:16 Varies with 3326** external state 3327** of DEVSEL#, 3328** STOP#, and 3329** TRDY#, 3330** during 3331** P_RST# 3332** PCI-X capability - These two bits define the mode of 3333** the PCI bus (conventional or PCI-X) as well as the 3334** operating frequency in the case of PCI-X mode. 3335** 00 - Conventional PCI mode 3336** 01 - PCI-X 66 3337** 10 - PCI-X 100 3338** 11 - PCI-X 133 3339** As defined by the PCI-X Addendum to the PCI Local Bus Specification, 3340** Revision 1.0a, the operating 3341** mode is determined by an initialization pattern on the PCI bus during 3342** P_RST# assertion: 3343** DEVSEL# STOP# TRDY# Mode 3344** Deasserted Deasserted Deasserted Conventional 3345** Deasserted Deasserted Asserted PCI-X 66 3346** Deasserted Asserted Deasserted PCI-X 100 3347** Deasserted Asserted Asserted PCI-X 133 3348** All other patterns are reserved. 3349** 15 0 2 3350** Outbound Transaction Queue Busy: 3351** 0=Outbound Transaction Queue Empty 3352** 1=Outbound Transaction Queue Busy 3353** 14 0 2 3354** Inbound Transaction Queue Busy: 3355** 0=Inbound Transaction Queue Empty 3356** 1=Inbound Transaction Queue Busy 3357** 13 0 2 Reserved. 3358** 12 0 2 Discard Timer Value - This bit controls the time-out value 3359** for the four discard timers attached to the queues holding read data. 3360** A value of 0 indicates the time-out value is 2 15 clocks. 3361** A value of 1 indicates the time-out value is 2 10 clocks. 3362** 11 0 2 Reserved. 3363** 10 Varies with 3364** external state 3365** of M66EN 3366** during 3367** P_RST# 3368** Bus Operating at 66 MHz - When set, the interface has been initialized to function at 66 MHz in 3369** Conventional PCI mode by the assertion of M66EN during bus initialization. 3370** When clear, the interface 3371** has been initialized as a 33 MHz bus. 3372** NOTE: When PCSR bits 17:16 are not equal to zero, then this bit is meaningless since the 80331 is operating in PCI-X mode. 3373** 09 0 2 Reserved 3374** 08 Varies with 3375** external state 3376** of REQ64# 3377** during 3378** P_RST# 3379** PCI Bus 64-Bit Capable - When clear, the PCI bus interface has been 3380** configured as 64-bit capable by 3381** the assertion of REQ64# on the rising edge of P_RST#. When set, 3382** the PCI interface is configured as 3383** 32-bit only. 3384** 07:06 00 2 Reserved. 3385** 05 0 2 Reset Internal Bus - This bit controls the reset of the Intel XScale core 3386** and all units on the internal 3387** bus. In addition to the internal bus initialization, 3388** this bit triggers the assertion of the M_RST# pin for 3389** initialization of registered DIMMs. When set: 3390** When operating in the conventional PCI mode: 3391** �E All current PCI transactions being mastered by the ATU completes, 3392** and the ATU master interfaces 3393** proceeds to an idle state. No additional transactions is mastered by these units 3394** until the internal bus reset is complete. 3395** �E All current transactions being slaved by the ATU on either the PCI bus 3396** or the internal bus 3397** completes, and the ATU target interfaces proceeds to an idle state. 3398** All future slave transactions master aborts, 3399** with the exception of the completion cycle for the transaction that set the Reset 3400** Internal Bus bit in the PCSR. 3401** �E When the value of the Core Processor Reset bit in the PCSR (upon P_RST# assertion) 3402** is set, the Intel XScale core is held in reset when the internal bus reset is complete. 3403** �E The ATU ignores configuration cycles, and they appears as master aborts for: 32 3404** Internal Bus clocks. 3405** �E The 80331 hardware clears this bit after the reset operation completes. 3406** When operating in the PCI-X mode: 3407** The ATU hardware responds the same as in Conventional PCI-X mode. 3408** However, this may create a problem in PCI-X mode for split requests in 3409** that there may still be an outstanding split completion that the 3410** ATU is either waiting to receive (Outbound Request) or initiate 3411** (Inbound Read Request). For a cleaner 3412** internal bus reset, host software can take the following steps prior 3413** to asserting Reset Internal bus: 3414** 1. Clear the Bus Master (bit 2 of the ATUCMD) and the Memory Enable (bit 1 of the ATUCMD) bits in 3415** the ATUCMD. This ensures that no new transactions, either outbound or inbound are enqueued. 3416** 2. Wait for both the Outbound (bit 15 of the PCSR) and Inbound Read (bit 14 of the PCSR) Transaction 3417** queue busy bits to be clear. 3418** 3. Set the Reset Internal Bus bit 3419** As a result, the ATU hardware resets the internal bus using the same logic as in conventional mode, 3420** however the user is now assured that the ATU no longer has any pending inbound or outbound split 3421** completion transactions. 3422** NOTE: Since the Reset Internal Bus bit is set using an inbound configuration cycle, the user is 3423** guaranteed that any prior configuration cycles have properly completed since there is only a one 3424** deep transaction queue for configuration transaction requests. The ATU sends the appropriate 3425** Split Write Completion Message to the Requester prior to the onset of Internal Bus Reset. 3426** 04 0 2 Bus Master Indicator Enable: Provides software control for the 3427** Bus Master Indicator signal P_BMI used 3428** for external RAIDIOS logic control of private devices. Only valid when operating with the bridge and 3429** central resource/arbiter disabled (BRG_EN =low, ARB_EN=low). 3430** 03 Varies with external state of PRIVDEV during 3431** P_RST# 3432** Private Device Enable - This bit indicates the state of the reset strap which enables the private device 3433** control mechanism within the PCI-to-PCI Bridge SISR configuration register. 3434** 0=Private Device control Disabled - SISR register bits default to zero 3435** 1=Private Device control Enabled - SISR register bits default to one 3436** 02 Varies with external state of RETRY during P_RST# 3437** Configuration Cycle Retry - When this bit is set, the PCI interface of the 80331 responds to all 3438** configuration cycles with a Retry condition. When clear, the 80331 responds to the appropriate 3439** configuration cycles. 3440** The default condition for this bit is based on the external state of the RETRY pin at the rising edge of 3441** P_RST#. When the external state of the pin is high, the bit is set. When the external state of the pin is 3442** low, the bit is cleared. 3443** 01 Varies with external state of CORE_RST# during P_RST# 3444** Core Processor Reset - This bit is set to its default value by the hardware when either P_RST# is 3445** asserted or the Reset Internal Bus bit in PCSR is set. When this bit is set, the Intel XScale core is 3446** being held in reset. Software cannot set this bit. Software is required to clear this bit to deassert Intel 3447** XScale core reset. 3448** The default condition for this bit is based on the external state of the CORE_RST# pin at the rising edge 3449** of P_RST#. When the external state of the pin is low, the bit is set. When the external state of the pin is 3450** high, the bit is clear. 3451** 00 Varies with external state of PRIVMEM during P_RST# 3452** Private Memory Enable - This bit indicates the state of the reset strap which enables the private device 3453** control mechanism within the PCI-to-PCI Bridge SDER configuration register. 3454** 0=Private Memory control Disabled - SDER register bit 2 default to zero 3455** 1=Private Memory control Enabled - SDER register bits 2 default to one 3456*********************************************************************************** 3457*/ 3458#define ARCMSR_PCI_CONFIGURATION_STATUS_REG 0x84 /*dword 0x87,0x86,0x85,0x84*/ 3459/* 3460*********************************************************************************** 3461** ATU Interrupt Status Register - ATUISR 3462** 3463** The ATU Interrupt Status Register is used to notify the core processor of the source of an ATU 3464** interrupt. In addition, this register is written to clear the source of the interrupt to the interrupt unit 3465** of the 80331. All bits in this register are Read/Clear. 3466** Bits 4:0 are a direct reflection of bits 14:11 and bit 8 (respectively) of the ATU Status Register 3467** (these bits are set at the same time by hardware but need to be cleared independently). Bit 7 is set 3468** by an error associated with the internal bus of the 80331. Bit 8 is for software BIST. The 3469** conditions that result in an ATU interrupt are cleared by writing a 1 to the appropriate bits in this 3470** register. 3471** Note: Bits 4:0, and bits 15 and 13:7 can result in an interrupt being driven to the Intel XScale core. 3472** ----------------------------------------------------------------- 3473** Bit Default Description 3474** 31:18 0000H Reserved 3475** 17 0 2 VPD Address Register Updated - This bit is set when a PCI bus configuration write occurs to the VPDAR 3476** register. Configuration register writes to the VPDAR does NOT result in bit 15 also being set. When set, 3477** this bit results in the assertion of the ATU Configure Register Write Interrupt. 3478** 16 0 2 Reserved 3479** 15 0 2 ATU Configuration Write - This bit is set when a PCI bus configuration write occurs to any ATU register. 3480** When set, this bit results in the assertion of the ATU Configure Register Write Interrupt. 3481** 14 0 2 ATU Inbound Memory Window 1 Base Updated - This bit is set when a PCI bus configuration write 3482** occurs to either the IABAR1 register or the IAUBAR1 register. Configuration register writes to these 3483** registers deos NOT result in bit 15 also being set. When set, this bit results in the assertion of the ATU 3484** Configure Register Write Interrupt. 3485** 13 0 2 Initiated Split Completion Error Message - This bit is set when the device initiates a Split Completion 3486** Message on the PCI Bus with the Split Completion Error attribute bit set. 3487** 12 0 2 Received Split Completion Error Message - This bit is set when the device receives a Split Completion 3488** Message from the PCI Bus with the Split Completion Error attribute bit set. 3489** 11 0 2 Power State Transition - When the Power State Field of the ATU Power Management Control/Status 3490** Register is written to transition the ATU function Power State from D0 to D3, D0 to D1, or D3 to D0 and 3491** the ATU Power State Transition Interrupt mask bit is cleared, this bit is set. 3492** 10 0 2 P_SERR# Asserted - set when P_SERR# is asserted on the PCI bus by the ATU. 3493** 09 0 2 Detected Parity Error - set when a parity error is detected on the PCI bus even when the ATUCMD 3494** register��s Parity Error Response bit is cleared. Set under the following conditions: 3495** �E Write Data Parity Error when the ATU is a target (inbound write). 3496** �E Read Data Parity Error when the ATU is an initiator (outbound read). 3497** �E Any Address or Attribute (PCI-X Only) Parity Error on the Bus. 3498** 08 0 2 ATU BIST Interrupt - When set, generates the ATU BIST Start Interrupt and indicates the host processor 3499** has set the Start BIST bit (ATUBISTR register bit 6), when the ATU BIST interrupt is enabled (ATUCR 3500** register bit 3). The Intel XScale core can initiate the software BIST and store the result in ATUBISTR 3501** register bits 3:0. 3502** Configuration register writes to the ATUBISTR does NOT result in bit 15 also being set or the assertion 3503** of the ATU Configure Register Write Interrupt. 3504** 07 0 2 Internal Bus Master Abort - set when a transaction initiated by the ATU internal bus initiator interface ends in a Master-abort. 3505** 06:05 00 2 Reserved. 3506** 04 0 2 P_SERR# Detected - set when P_SERR# is detected on the PCI bus by the ATU. 3507** 03 0 2 PCI Master Abort - set when a transaction initiated by the ATU PCI initiator interface ends in a Master-abort. 3508** 02 0 2 PCI Target Abort (master) - set when a transaction initiated by the ATU PCI master interface ends in a Target-abort. 3509** 01 0 2 PCI Target Abort (target) - set when the ATU interface, acting as a target, terminates the transaction on the PCI bus with a target abort. 3510** 00 0 2 PCI Master Parity Error - Master Parity Error - The ATU interface sets this bit under the following 3511** conditions: 3512** �E The ATU asserted PERR# itself or the ATU observed PERR# asserted. 3513** �E And the ATU acted as the requester for the operation in which the error occurred. 3514** �E And the ATUCMD register��s Parity Error Response bit is set 3515** �E Or (PCI-X Mode Only) the ATU received a Write Data Parity Error Message 3516** �E And the ATUCMD register��s Parity Error Response bit is set 3517*********************************************************************************** 3518*/ 3519#define ARCMSR_ATU_INTERRUPT_STATUS_REG 0x88 /*dword 0x8B,0x8A,0x89,0x88*/ 3520/* 3521*********************************************************************************** 3522** ATU Interrupt Mask Register - ATUIMR 3523** 3524** The ATU Interrupt Mask Register contains the control bit to enable and disable interrupts 3525** generated by the ATU. 3526** ----------------------------------------------------------------- 3527** Bit Default Description 3528** 31:15 0 0000H Reserved 3529** 14 0 2 VPD Address Register Updated Mask - Controls the setting of bit 17 of the ATUISR and generation of the 3530** ATU Configuration Register Write interrupt when a PCI bus write occurs to the VPDAR register. 3531** 0=Not Masked 3532** 1=Masked 3533** 13 0 2 Reserved 3534** 12 0 2 Configuration Register Write Mask - Controls the setting of bit 15 of the ATUISR and generation of the 3535** ATU Configuration Register Write interrupt when a PCI bus write occurs to any ATU configuration register 3536** except those covered by mask bit 11 and bit 14 of this register, and ATU BIST enable bit 3 of the ATUCR. 3537** 0=Not Masked 3538** 1=Masked 3539** 11 1 2 ATU Inbound Memory Window 1 Base Updated Mask - Controls the setting of bit 14 of the ATUISR and 3540** generation of the ATU Configuration Register Write interrupt when a PCI bus write occurs to either the 3541** IABAR1 register or the IAUBAR1 register. 3542** 0=Not Masked 3543** 1=Masked 3544** 10 0 2 Initiated Split Completion Error Message Interrupt Mask - Controls the setting of bit 13 of the ATUISR and 3545** generation of the ATU Error interrupt when the ATU initiates a Split Completion Error Message. 3546** 0=Not Masked 3547** 1=Masked 3548** 09 0 2 Received Split Completion Error Message Interrupt Mask- Controls the setting of bit 12 of the ATUISR 3549** and generation of the ATU Error interrupt when a Split Completion Error Message results in bit 29 of the 3550** PCIXSR being set. 3551** 0=Not Masked 3552** 1=Masked 3553** 08 1 2 Power State Transition Interrupt Mask - Controls the setting of bit 12 of the ATUISR and generation of the 3554** ATU Error interrupt when ATU Power Management Control/Status Register is written to transition the 3555** ATU Function Power State from D0 to D3, D0 to D1, D1 to D3 or D3 to D0. 3556** 0=Not Masked 3557** 1=Masked 3558** 07 0 2 ATU Detected Parity Error Interrupt Mask - Controls the setting of bit 9 of the ATUISR and generation of 3559** the ATU Error interrupt when a parity error detected on the PCI bus that sets bit 15 of the ATUSR. 3560** 0=Not Masked 3561** 1=Masked 3562** 06 0 2 ATU SERR# Asserted Interrupt Mask - Controls the setting of bit 10 of the ATUISR and generation of the 3563** ATU Error interrupt when SERR# is asserted on the PCI interface resulting in bit 14 of the ATUSR being set. 3564** 0=Not Masked 3565** 1=Masked 3566** NOTE: This bit is specific to the ATU asserting SERR# and not detecting SERR# from another master. 3567** 05 0 2 ATU PCI Master Abort Interrupt Mask - Controls the setting of bit 3 of the ATUISR and generation of the 3568** ATU Error interrupt when a master abort error resulting in bit 13 of the ATUSR being set. 3569** 0=Not Masked 3570** 1=Masked 3571** 04 0 2 ATU PCI Target Abort (Master) Interrupt Mask- Controls the setting of bit 12 of the ATUISR and ATU Error 3572** generation of the interrupt when a target abort error resulting in bit 12 of the ATUSR being set 3573** 0=Not Masked 3574** 1=Masked 3575** 03 0 2 ATU PCI Target Abort (Target) Interrupt Mask- Controls the setting of bit 1 of the ATUISR and generation 3576** of the ATU Error interrupt when a target abort error resulting in bit 11 of the ATUSR being set. 3577** 0=Not Masked 3578** 1=Masked 3579** 02 0 2 ATU PCI Master Parity Error Interrupt Mask - Controls the setting of bit 0 of the ATUISR and generation 3580** of the ATU Error interrupt when a parity error resulting in bit 8 of the ATUSR being set. 3581** 0=Not Masked 3582** 1=Masked 3583** 01 0 2 ATU Inbound Error SERR# Enable - Controls when the ATU asserts (when enabled through the 3584** ATUCMD) SERR# on the PCI interface in response to a master abort on the internal bus during an 3585** inbound write transaction. 3586** 0=SERR# Not Asserted due to error 3587** 1=SERR# Asserted due to error 3588** 00 0 2 ATU ECC Target Abort Enable - Controls the ATU response on the PCI interface to a target abort (ECC 3589** error) from the memory controller on the internal bus. In conventional mode, this action only occurs 3590** during an inbound read transaction where the data phase that was target aborted on the internal bus is 3591** actually requested from the inbound read queue. 3592** 0=Disconnect with data 3593** (the data being up to 64 bits of 1��s) 3594** 1=Target Abort 3595** NOTE: In PCI-X Mode, The ATU initiates a Split Completion Error Message (with message class=2h - 3596** completer error and message index=81h - 80331 internal bus target abort) on the PCI bus, 3597** independent of the setting of this bit. 3598*********************************************************************************** 3599*/ 3600#define ARCMSR_ATU_INTERRUPT_MASK_REG 0x8C /*dword 0x8F,0x8E,0x8D,0x8C*/ 3601/* 3602*********************************************************************************** 3603** Inbound ATU Base Address Register 3 - IABAR3 3604** 3605** . The Inbound ATU Base Address Register 3 (IABAR3) together with the Inbound ATU Upper Base Address Register 3 (IAUBAR3) defines the block 3606** of memory addresses where the inbound translation window 3 begins. 3607** . The inbound ATU decodes and forwards the bus request to the 80331 internal bus with a translated address to map into 80331 local memory. 3608** . The IABAR3 and IAUBAR3 define the base address and describes the required memory block size. 3609** . Bits 31 through 12 of the IABAR3 is either read/write bits or read only with a value of 0 depending on the value located within the IALR3. 3610** The programmed value within the base address register must comply with the PCI programming requirements for address alignment. 3611** Note: 3612** Since IABAR3 does not appear in the standard PCI configuration header space (offsets 00H - 3CH), 3613** IABAR3 is not configured by the host during normal system initialization. 3614** Warning: 3615** When a non-zero value is not written to IALR3, 3616** the user should not set either the Prefetchable Indicator 3617** or the Type Indicator for 64 bit addressability. 3618** This is the default for IABAR3. 3619** Assuming a non-zero value is written to IALR3, 3620** the user may set the Prefetchable Indicator 3621** or the Type Indicator: 3622** a. Since non prefetchable memory windows can never be placed above the 4 Gbyte address boundary, 3623** when the Prefetchable Indicator is not set, 3624** the user should also leave the Type Indicator set for 32 bit addressability. 3625** This is the default for IABAR3. 3626** b. when the Prefetchable Indicator is set, 3627** the user should also set the Type Indicator for 64 bit addressability. 3628** ----------------------------------------------------------------- 3629** Bit Default Description 3630** 31:12 00000H Translation Base Address 3 - These bits define the actual location 3631** the translation function is to respond to when addressed from the PCI bus. 3632** 11:04 00H Reserved. 3633** 03 0 2 Prefetchable Indicator - When set, defines the memory space as prefetchable. 3634** 02:01 00 2 Type Indicator - Defines the width of the addressability for this memory window: 3635** 00 - Memory Window is locatable anywhere in 32 bit address space 3636** 10 - Memory Window is locatable anywhere in 64 bit address space 3637** 00 0 2 Memory Space Indicator - This bit field describes memory or I/O space base address. 3638** The ATU does not occupy I/O space, 3639** thus this bit must be zero. 3640*********************************************************************************** 3641*/ 3642#define ARCMSR_INBOUND_ATU_BASE_ADDRESS3_REG 0x90 /*dword 0x93,0x92,0x91,0x90*/ 3643/* 3644*********************************************************************************** 3645** Inbound ATU Upper Base Address Register 3 - IAUBAR3 3646** 3647** This register contains the upper base address when decoding PCI addresses beyond 4 GBytes. 3648** Together with the Translation Base Address this register defines the actual location 3649** the translation function is to respond to when addressed from the PCI bus for addresses > 4GBytes (for DACs). 3650** The programmed value within the base address register must comply with the PCI programming 3651** requirements for address alignment. 3652** Note: 3653** When the Type indicator of IABAR3 is set to indicate 32 bit addressability, 3654** the IAUBAR3 register attributes are read-only. 3655** This is the default for IABAR3. 3656** ----------------------------------------------------------------- 3657** Bit Default Description 3658** 31:0 00000H Translation Upper Base Address 3 - Together with the Translation Base Address 3 these bits define 3659** the actual location the translation function is to respond to when addressed from the PCI bus for addresses > 4GBytes. 3660*********************************************************************************** 3661*/ 3662#define ARCMSR_INBOUND_ATU_UPPER_BASE_ADDRESS3_REG 0x94 /*dword 0x97,0x96,0x95,0x94*/ 3663/* 3664*********************************************************************************** 3665** Inbound ATU Limit Register 3 - IALR3 3666** 3667** Inbound address translation for memory window 3 occurs for data transfers occurring from the PCI 3668** bus (originated from the PCI bus) to the 80331 internal bus. The address translation block converts 3669** PCI addresses to internal bus addresses. 3670** The inbound translation base address for inbound window 3 is specified in Section 3.10.15. When 3671** determining block size requirements �X as described in Section 3.10.21 �X the translation limit 3672** register provides the block size requirements for the base address register. The remaining registers 3673** used for performing address translation are discussed in Section 3.2.1.1. 3674** The 80331 translate value register��s programmed value must be naturally aligned with the base 3675** address register��s programmed value. The limit register is used as a mask; thus, the lower address 3676** bits programmed into the 80331 translate value register are invalid. Refer to the PCI Local Bus 3677** Specification, Revision 2.3 for additional information on programming base address registers. 3678** Bits 31 to 12 within the IALR3 have a direct effect on the IABAR3 register, bits 31 to 12, with a 3679** one to one correspondence. A value of 0 in a bit within the IALR3 makes the corresponding bit 3680** within the IABAR3 a read only bit which always returns 0. A value of 1 in a bit within the IALR3 3681** makes the corresponding bit within the IABAR3 read/write from PCI. Note that a consequence of 3682** this programming scheme is that unless a valid value exists within the IALR3, all writes to the 3683** IABAR3 has no effect since a value of all zeros within the IALR3 makes the IABAR3 a read only 3684** register. 3685** ----------------------------------------------------------------- 3686** Bit Default Description 3687** 31:12 00000H Inbound Translation Limit 3 - This readback value determines the memory block size required 3688** for the ATUs memory window 3. 3689** 11:00 000H Reserved 3690*********************************************************************************** 3691*/ 3692#define ARCMSR_INBOUND_ATU_LIMIT3_REG 0x98 /*dword 0x9B,0x9A,0x99,0x98*/ 3693/* 3694*********************************************************************************** 3695** Inbound ATU Translate Value Register 3 - IATVR3 3696** 3697** The Inbound ATU Translate Value Register 3 (IATVR3) contains the internal bus address used to 3698** convert PCI bus addresses. The converted address is driven on the internal bus as a result of the 3699** inbound ATU address translation. 3700** ----------------------------------------------------------------- 3701** Bit Default Description 3702** 31:12 00000H Inbound ATU Translation Value 3 - This value is used to convert the PCI address to internal bus addresses. 3703** This value must be 64-bit aligned on the internal bus. The default address allows the ATU to 3704** access the internal 80331 memory-mapped registers. 3705** 11:00 000H Reserved 3706*********************************************************************************** 3707*/ 3708#define ARCMSR_INBOUND_ATU_TRANSLATE_VALUE3_REG 0x9C /*dword 0x9F,0x9E,0x9D,0x9C*/ 3709/* 3710*********************************************************************************** 3711** Outbound Configuration Cycle Address Register - OCCAR 3712** 3713** The Outbound Configuration Cycle Address Register is used to hold the 32-bit PCI configuration 3714** cycle address. The Intel XScale core writes the PCI configuration cycles address which then 3715** enables the outbound configuration read or write. The Intel XScale core then performs a read or 3716** write to the Outbound Configuration Cycle Data Register to initiate the configuration cycle on the 3717** PCI bus. 3718** Note: Bits 15:11 of the configuration cycle address for Type 0 configuration cycles are defined differently 3719** for Conventional versus PCI-X modes. When 80331 software programs the OCCAR to initiate a 3720** Type 0 configuration cycle, the OCCAR should always be loaded based on the PCI-X definition for 3721** the Type 0 configuration cycle address. When operating in Conventional mode, the 80331 clears 3722** bits 15:11 of the OCCAR prior to initiating an outbound Type 0 configuration cycle. See the PCI-X 3723** Addendum to the PCI Local Bus Specification, Revision 1.0a for details on the two formats. 3724** ----------------------------------------------------------------- 3725** Bit Default Description 3726** 31:00 0000 0000H Configuration Cycle Address - These bits define the 32-bit PCI address used during an outbound 3727** configuration read or write cycle. 3728*********************************************************************************** 3729*/ 3730#define ARCMSR_OUTBOUND_CONFIGURATION_CYCLE_ADDRESS_REG 0xA4 /*dword 0xA7,0xA6,0xA5,0xA4*/ 3731/* 3732*********************************************************************************** 3733** Outbound Configuration Cycle Data Register - OCCDR 3734** 3735** The Outbound Configuration Cycle Data Register is used to initiate a configuration read or write 3736** on the PCI bus. The register is logical rather than physical meaning that it is an address not a 3737** register. The Intel XScale core reads or writes the data registers memory-mapped address to 3738** initiate the configuration cycle on the PCI bus with the address found in the OCCAR. For a 3739** configuration write, the data is latched from the internal bus and forwarded directly to the OWQ. 3740** For a read, the data is returned directly from the ORQ to the Intel XScale core and is never 3741** actually entered into the data register (which does not physically exist). 3742** The OCCDR is only visible from 80331 internal bus address space and appears as a reserved value 3743** within the ATU configuration space. 3744** ----------------------------------------------------------------- 3745** Bit Default Description 3746** 31:00 0000 0000H Configuration Cycle Data - These bits define the data used during an outbound configuration read 3747** or write cycle. 3748*********************************************************************************** 3749*/ 3750#define ARCMSR_OUTBOUND_CONFIGURATION_CYCLE_DATA_REG 0xAC /*dword 0xAF,0xAE,0xAD,0xAC*/ 3751/* 3752*********************************************************************************** 3753** VPD Capability Identifier Register - VPD_CAPID 3754** 3755** The Capability Identifier Register bits adhere to the definitions in the PCI Local Bus Specification, 3756** Revision 2.3. This register in the PCI Extended Capability header identifies the type of Extended 3757** Capability contained in that header. In the case of the 80331, this is the VPD extended capability 3758** with an ID of 03H as defined by the PCI Local Bus Specification, Revision 2.3. 3759** ----------------------------------------------------------------- 3760** Bit Default Description 3761** 07:00 03H Cap_Id - This field with its�� 03H value identifies this item in the linked list of Extended Capability 3762** Headers as being the VPD capability registers. 3763*********************************************************************************** 3764*/ 3765#define ARCMSR_VPD_CAPABILITY_IDENTIFIER_REG 0xB8 /*byte*/ 3766/* 3767*********************************************************************************** 3768** VPD Next Item Pointer Register - VPD_NXTP 3769** 3770** The Next Item Pointer Register bits adhere to the definitions in the PCI Local Bus Specification, 3771** Revision 2.3. This register describes the location of the next item in the function��s capability list. 3772** For the 80331, this the final capability list, and hence, this register is set to 00H. 3773** ----------------------------------------------------------------- 3774** Bit Default Description 3775** 07:00 00H Next_ Item_ Pointer - This field provides an offset into the function��s configuration space pointing to the 3776** next item in the function��s capability list. Since the VPD capabilities are the last in the linked list of 3777** extended capabilities in the 80331, the register is set to 00H. 3778*********************************************************************************** 3779*/ 3780#define ARCMSR_VPD_NEXT_ITEM_PTR_REG 0xB9 /*byte*/ 3781/* 3782*********************************************************************************** 3783** VPD Address Register - VPD_AR 3784** 3785** The VPD Address register (VPDAR) contains the DWORD-aligned byte address of the VPD to be 3786** accessed. The register is read/write and the initial value at power-up is indeterminate. 3787** A PCI Configuration Write to the VPDAR interrupts the Intel XScale core. Software can use 3788** the Flag setting to determine whether the configuration write was intended to initiate a read or 3789** write of the VPD through the VPD Data Register. 3790** ----------------------------------------------------------------- 3791** Bit Default Description 3792** 15 0 2 Flag - A flag is used to indicate when a transfer of data between the VPD Data Register and the storage 3793** component has completed. Please see Section 3.9, ��Vital Product Data�� on page 201 for more details on 3794** how the 80331 handles the data transfer. 3795** 14:0 0000H VPD Address - This register is written to set the DWORD-aligned byte address used to read or write 3796** Vital Product Data from the VPD storage component. 3797*********************************************************************************** 3798*/ 3799#define ARCMSR_VPD_ADDRESS_REG 0xBA /*word 0xBB,0xBA*/ 3800/* 3801*********************************************************************************** 3802** VPD Data Register - VPD_DR 3803** 3804** This register is used to transfer data between the 80331 and the VPD storage component. 3805** ----------------------------------------------------------------- 3806** Bit Default Description 3807** 31:00 0000H VPD Data - Four bytes are always read or written through this register to/from the VPD storage component. 3808*********************************************************************************** 3809*/ 3810#define ARCMSR_VPD_DATA_REG 0xBC /*dword 0xBF,0xBE,0xBD,0xBC*/ 3811/* 3812*********************************************************************************** 3813** Power Management Capability Identifier Register -PM_CAPID 3814** 3815** The Capability Identifier Register bits adhere to the definitions in the PCI Local Bus Specification, 3816** Revision 2.3. This register in the PCI Extended Capability header identifies the type of Extended 3817** Capability contained in that header. In the case of the 80331, this is the PCI Bus Power 3818** Management extended capability with an ID of 01H as defined by the PCI Bus Power Management 3819** Interface Specification, Revision 1.1. 3820** ----------------------------------------------------------------- 3821** Bit Default Description 3822** 07:00 01H Cap_Id - This field with its�� 01H value identifies this item in the linked list of Extended Capability 3823** Headers as being the PCI Power Management Registers. 3824*********************************************************************************** 3825*/ 3826#define ARCMSR_POWER_MANAGEMENT_CAPABILITY_IDENTIFIER_REG 0xC0 /*byte*/ 3827/* 3828*********************************************************************************** 3829** Power Management Next Item Pointer Register - PM_NXTP 3830** 3831** The Next Item Pointer Register bits adhere to the definitions in the PCI Local Bus Specification, 3832** Revision 2.3. This register describes the location of the next item in the function��s capability list. 3833** For the 80331, the next capability (MSI capability list) is located at off-set D0H. 3834** ----------------------------------------------------------------- 3835** Bit Default Description 3836** 07:00 D0H Next_ Item_ Pointer - This field provides an offset into the function��s configuration space pointing to the 3837** next item in the function��s capability list which in the 80331 is the MSI extended capabilities header. 3838*********************************************************************************** 3839*/ 3840#define ARCMSR_POWER_NEXT_ITEM_PTR_REG 0xC1 /*byte*/ 3841/* 3842*********************************************************************************** 3843** Power Management Capabilities Register - PM_CAP 3844** 3845** Power Management Capabilities bits adhere to the definitions in the PCI Bus Power Management 3846** Interface Specification, Revision 1.1. This register is a 16-bit read-only register which provides 3847** information on the capabilities of the ATU function related to power management. 3848** ----------------------------------------------------------------- 3849** Bit Default Description 3850** 15:11 00000 2 PME_Support - This function is not capable of asserting the PME# signal in any state, since PME# 3851** is not supported by the 80331. 3852** 10 0 2 D2_Support - This bit is set to 0 2 indicating that the 80331 does not support the D2 Power Management State 3853** 9 1 2 D1_Support - This bit is set to 1 2 indicating that the 80331 supports the D1 Power Management State 3854** 8:6 000 2 Aux_Current - This field is set to 000 2 indicating that the 80331 has no current requirements for the 3855** 3.3Vaux signal as defined in the PCI Bus Power Management Interface Specification, Revision 1.1 3856** 5 0 2 DSI - This field is set to 0 2 meaning that this function requires a device specific initialization sequence 3857** following the transition to the D0 uninitialized state. 3858** 4 0 2 Reserved. 3859** 3 0 2 PME Clock - Since the 80331 does not support PME# signal generation this bit is cleared to 0 2 . 3860** 2:0 010 2 Version - Setting these bits to 010 2 means that this function complies with PCI Bus Power Management 3861** Interface Specification, Revision 1.1 3862*********************************************************************************** 3863*/ 3864#define ARCMSR_POWER_MANAGEMENT_CAPABILITY_REG 0xC2 /*word 0xC3,0xC2*/ 3865/* 3866*********************************************************************************** 3867** Power Management Control/Status Register - PM_CSR 3868** 3869** Power Management Control/Status bits adhere to the definitions in the PCI Bus Power 3870** Management Interface Specification, Revision 1.1. This 16-bit register is the control and status 3871** interface for the power management extended capability. 3872** ----------------------------------------------------------------- 3873** Bit Default Description 3874** 15 0 2 PME_Status - This function is not capable of asserting the PME# signal in any state, since PME## is not 3875** supported by the 80331. 3876** 14:9 00H Reserved 3877** 8 0 2 PME_En - This bit is hardwired to read-only 0 2 since this function does not support PME# 3878** generation from any power state. 3879** 7:2 000000 2 Reserved 3880** 1:0 00 2 Power State - This 2-bit field is used both to determine the current power state 3881** of a function and to set the function into a new power state. The definition of the values is: 3882** 00 2 - D0 3883** 01 2 - D1 3884** 10 2 - D2 (Unsupported) 3885** 11 2 - D3 hot 3886** The 80331 supports only the D0 and D3 hot states. 3887** 3888*********************************************************************************** 3889*/ 3890#define ARCMSR_POWER_MANAGEMENT_CONTROL_STATUS_REG 0xC4 /*word 0xC5,0xC4*/ 3891/* 3892*********************************************************************************** 3893** PCI-X Capability Identifier Register - PX_CAPID 3894** 3895** The Capability Identifier Register bits adhere to the definitions in the PCI Local Bus Specification, 3896** Revision 2.3. This register in the PCI Extended Capability header identifies the type of Extended 3897** Capability contained in that header. In the case of the 80331, this is the PCI-X extended capability with 3898** an ID of 07H as defined by the PCI-X Addendum to the PCI Local Bus Specification, Revision 1.0a. 3899** ----------------------------------------------------------------- 3900** Bit Default Description 3901** 07:00 07H Cap_Id - This field with its�� 07H value identifies this item in the linked list of Extended Capability 3902** Headers as being the PCI-X capability registers. 3903*********************************************************************************** 3904*/ 3905#define ARCMSR_PCIX_CAPABILITY_IDENTIFIER_REG 0xE0 /*byte*/ 3906/* 3907*********************************************************************************** 3908** PCI-X Next Item Pointer Register - PX_NXTP 3909** 3910** The Next Item Pointer Register bits adhere to the definitions in the PCI Local Bus Specification, 3911** Revision 2.3. This register describes the location of the next item in the function��s capability list. 3912** By default, the PCI-X capability is the last capabilities list for the 80331, thus this register defaults 3913** to 00H. 3914** However, this register may be written to B8H prior to host configuration to include the VPD 3915** capability located at off-set B8H. 3916** Warning: Writing this register to any value other than 00H (default) or B8H is not supported and may 3917** produce unpredictable system behavior. 3918** In order to guarantee that this register is written prior to host configuration, the 80331 must be 3919** initialized at P_RST# assertion to Retry Type 0 configuration cycles (bit 2 of PCSR). Typically, 3920** the Intel XScale core would be enabled to boot immediately following P_RST# assertion in 3921** this case (bit 1 of PCSR), as well. Please see Table 125, ��PCI Configuration and Status Register - 3922** PCSR�� on page 253 for more details on the 80331 initialization modes. 3923** ----------------------------------------------------------------- 3924** Bit Default Description 3925** 07:00 00H Next_ Item_ Pointer - This field provides an offset into the function��s configuration space pointing to the 3926** next item in the function��s capability list. Since the PCI-X capabilities are the last in the linked list of 3927** extended capabilities in the 80331, the register is set to 00H. 3928** However, this field may be written prior to host configuration with B8H to extend the list to include the 3929** VPD extended capabilities header. 3930*********************************************************************************** 3931*/ 3932#define ARCMSR_PCIX_NEXT_ITEM_PTR_REG 0xE1 /*byte*/ 3933/* 3934*********************************************************************************** 3935** PCI-X Command Register - PX_CMD 3936** 3937** This register controls various modes and features of ATU and Message Unit when operating in the 3938** PCI-X mode. 3939** ----------------------------------------------------------------- 3940** Bit Default Description 3941** 15:7 000000000 2 Reserved. 3942** 6:4 011 2 Maximum Outstanding Split Transactions - This register sets the maximum number of Split Transactions 3943** the device is permitted to have outstanding at one time. 3944** Register Maximum Outstanding 3945** 0 1 3946** 1 2 3947** 2 3 3948** 3 4 3949** 4 8 3950** 5 12 3951** 6 16 3952** 7 32 3953** 3:2 00 2 Maximum Memory Read Byte Count - This register sets the maximum byte count the device uses when 3954** initiating a Sequence with one of the burst memory read commands. 3955** Register Maximum Byte Count 3956** 0 512 3957** 1 1024 3958** 2 2048 3959** 3 4096 3960** 1 0 2 3961** Enable Relaxed Ordering - The 80331 does not set the relaxed ordering bit in the Requester Attributes 3962** of Transactions. 3963** 0 0 2 Data Parity Error Recovery Enable - The device driver sets this bit to enable the device to attempt to 3964** recover from data parity errors. When this bit is 0 and the device is in PCI-X mode, the device asserts 3965** SERR# (when enabled) whenever the Master Data Parity Error bit (Status register, bit 8) is set. 3966*********************************************************************************** 3967*/ 3968#define ARCMSR_PCIX_COMMAND_REG 0xE2 /*word 0xE3,0xE2*/ 3969/* 3970*********************************************************************************** 3971** PCI-X Status Register - PX_SR 3972** 3973** This register identifies the capabilities and current operating mode of ATU, DMAs and Message 3974** Unit when operating in the PCI-X mode. 3975** ----------------------------------------------------------------- 3976** Bit Default Description 3977** 31:30 00 2 Reserved 3978** 29 0 2 Received Split Completion Error Message - This bit is set when the device receives a Split Completion 3979** Message with the Split Completion Error attribute bit set. Once set, this bit remains set until software 3980** writes a 1 to this location. 3981** 0=no Split Completion error message received. 3982** 1=a Split Completion error message has been received. 3983** 28:26 001 2 Designed Maximum Cumulative Read Size (DMCRS) - The value of this register depends on the setting 3984** of the Maximum Memory Read Byte Count field of the PCIXCMD register: 3985** DMCRS Max ADQs Maximum Memory Read Byte Count Register Setting 3986** 1 16 512 (Default) 3987** 2 32 1024 3988** 2 32 2048 3989** 2 32 4096 3990** 25:23 011 2 Designed Maximum Outstanding Split Transactions - The 80331 can have up to four outstanding split transactions. 3991** 22:21 01 2 Designed Maximum Memory Read Byte Count - The 80331 can generate memory reads with byte counts up 3992** to 1024 bytes. 3993** 20 1 2 80331 is a complex device. 3994** 19 0 2 Unexpected Split Completion - This bit is set when an unexpected Split Completion with this device��s 3995** Requester ID is received. Once set, this bit remains set until software writes a 1 to this location. 3996** 0=no unexpected Split Completion has been received. 3997** 1=an unexpected Split Completion has been received. 3998** 18 0 2 Split Completion Discarded - This bit is set when the device discards a Split Completion because the 3999** requester would not accept it. See Section 5.4.4 of the PCI-X Addendum to the PCI Local Bus 4000** Specification, Revision 1.0a for details. Once set, this bit remains set until software writes a 1 to this 4001** location. 4002** 0=no Split Completion has been discarded. 4003** 1=a Split Completion has been discarded. 4004** NOTE: The 80331 does not set this bit since there is no Inbound address responding to Inbound Read 4005** Requests with Split Responses (Memory or Register) that has ��read side effects.�� 4006** 17 1 2 80331 is a 133 MHz capable device. 4007** 16 1 2 or P_32BITPCI# 80331 with bridge enabled (BRG_EN=1) implements the ATU with a 64-bit interface on the secondary PCI bus, 4008** therefore this bit is always set. 4009** 80331 with no bridge and central resource disabled (BRG_EN=0, ARB_EN=0), 4010** use this bit to identify the add-in card to the system as 64-bit or 32-bit wide via a user-configurable strap (P_32BITPCI#). 4011** This strap, by default, identifies the add in card based on 80331 with bridge disabled 4012** as 64-bit unless the user attaches the appropriate pull-down resistor to the strap. 4013** 0=The bus is 32 bits wide. 4014** 1=The bus is 64 bits wide. 4015** 15:8 FFH Bus Number - This register is read for diagnostic purposes only. It indicates the number of the bus 4016** segment for the device containing this function. The function uses this number as part of its Requester 4017** ID and Completer ID. For all devices other than the source bridge, each time the function is addressed 4018** by a Configuration Write transaction, the function must update this register with the contents of AD[7::0] 4019** of the attribute phase of the Configuration Write, regardless of which register in the function is 4020** addressed by the transaction. The function is addressed by a Configuration Write transaction when all of 4021** the following are true: 4022** 1. The transaction uses a Configuration Write command. 4023** 2. IDSEL is asserted during the address phase. 4024** 3. AD[1::0] are 00b (Type 0 configuration transaction). 4025** 4. AD[10::08] of the configuration address contain the appropriate function number. 4026** 7:3 1FH Device Number - This register is read for diagnostic purposes only. It indicates the number of the device 4027** containing this function, i.e., the number in the Device Number field (AD[15::11]) of the address of a 4028** Type 0 configuration transaction that is assigned to the device containing this function by the connection 4029** of the system hardware. The system must assign a device number other than 00h (00h is reserved for 4030** the source bridge). The function uses this number as part of its Requester ID and Completer ID. Each 4031** time the function is addressed by a Configuration Write transaction, the device must update this register 4032** with the contents of AD[15::11] of the address phase of the Configuration Write, regardless of which 4033** register in the function is addressed by the transaction. The function is addressed by a Configuration 4034** Write transaction when all of the following are true: 4035** 1. The transaction uses a Configuration Write command. 4036** 2. IDSEL is asserted during the address phase. 4037** 3. AD[1::0] are 00b (Type 0 configuration transaction). 4038** 4. AD[10::08] of the configuration address contain the appropriate function number. 4039** 2:0 000 2 Function Number - This register is read for diagnostic purposes only. It indicates the number of this 4040** function; i.e., the number in the Function Number field (AD[10::08]) of the address of a Type 0 4041** configuration transaction to which this function responds. The function uses this number as part of its 4042** Requester ID and Completer ID. 4043** 4044************************************************************************** 4045*/ 4046#define ARCMSR_PCIX_STATUS_REG 0xE4 /*dword 0xE7,0xE6,0xE5,0xE4*/ 4047 4048/* 4049************************************************************************** 4050** Inbound Read Transaction 4051** ======================================================================== 4052** An inbound read transaction is initiated by a PCI initiator and is targeted at either 80331 local 4053** memory or a 80331 memory-mapped register space. The read transaction is propagated through 4054** the inbound transaction queue (ITQ) and read data is returned through the inbound read queue 4055** (IRQ). 4056** When operating in the conventional PCI mode, all inbound read transactions are processed as 4057** delayed read transactions. When operating in the PCI-X mode, all inbound read transactions are 4058** processed as split transactions. The ATUs PCI interface claims the read transaction and forwards 4059** the read request through to the internal bus and returns the read data to the PCI bus. Data flow for 4060** an inbound read transaction on the PCI bus is summarized in the following statements: 4061** �E The ATU claims the PCI read transaction when the PCI address is within the inbound 4062** translation window defined by ATU Inbound Base Address Register (and Inbound Upper Base 4063** Address Register during DACs) and Inbound Limit Register. 4064** �E When operating in the conventional PCI mode, when the ITQ is currently holding transaction 4065** information from a previous delayed read, the current transaction information is compared to 4066** the previous transaction information (based on the setting of the DRC Alias bit in 4067** Section 3.10.39, ��ATU Configuration Register - ATUCR�� on page 252). When there is a 4068** match and the data is in the IRQ, return the data to the master on the PCI bus. When there is a 4069** match and the data is not available, a Retry is signaled with no other action taken. When there 4070** is not a match and when the ITQ has less than eight entries, capture the transaction 4071** information, signal a Retry and initiate a delayed transaction. When there is not a match and 4072** when the ITQ is full, then signal a Retry with no other action taken. 4073** �X When an address parity error is detected, the address parity response defined in 4074** Section 3.7 is used. 4075** �E When operating in the conventional PCI mode, once read data is driven onto the PCI bus from 4076** the IRQ, it continues until one of the following is true: 4077** �X The initiator completes the PCI transaction. When there is data left unread in the IRQ, the 4078** data is flushed. 4079** �X An internal bus Target Abort was detected. In this case, the QWORD associated with the 4080** Target Abort is never entered into the IRQ, and therefore is never returned. 4081** �X Target Abort or a Disconnect with Data is returned in response to the Internal Bus Error. 4082** �X The IRQ becomes empty. In this case, the PCI interface signals a Disconnect with data to 4083** the initiator on the last data word available. 4084** �E When operating in the PCI-X mode, when ITQ is not full, the PCI address, attribute and 4085** command are latched into the available ITQ and a Split Response Termination is signalled to 4086** the initiator. 4087** �E When operating in the PCI-X mode, when the transaction does not cross a 1024 byte aligned 4088** boundary, then the ATU waits until it receives the full byte count from the internal bus target 4089** before returning read data by generating the split completion transaction on the PCI-X bus. 4090** When the read requested crosses at least one 1024 byte boundary, then ATU completes the 4091** transfer by returning data in 1024 byte aligned chunks. 4092** �E When operating in the PCI-X mode, once a split completion transaction has started, it 4093** continues until one of the following is true: 4094** �X The requester (now the target) generates a Retry Termination, or a Disconnection at Next 4095** ADB (when the requester is a bridge) 4096** �X The byte count is satisfied. 4097** �X An internal bus Target Abort was detected. The ATU generates a Split Completion 4098** Message (message class=2h - completer error, and message index=81h - target abort) to 4099** inform the requester about the abnormal condition. The ITQ for this transaction is flushed. 4100** Refer to Section 3.7.1. 4101** �X An internal bus Master Abort was detected. The ATU generates a Split Completion 4102** Message (message class=2h - completer error, and message index=80h - Master abort) to 4103** inform the requester about the abnormal condition. The ITQ for this transaction is flushed. 4104** Refer to Section 3.7.1 4105** �E When operating in the conventional PCI mode, when the master inserts wait states on the PCI 4106** bus, the ATU PCI slave interface waits with no premature disconnects. 4107** �E When a data parity error occurs signified by PERR# asserted from the initiator, no action is 4108** taken by the target interface. Refer to Section 3.7.2.5. 4109** �E When operating in the conventional PCI mode, when the read on the internal bus is 4110** target-aborted, either a target-abort or a disconnect with data is signaled to the initiator. This is 4111** based on the ATU ECC Target Abort Enable bit (bit 0 of the ATUIMR for ATU). When set, a 4112** target abort is used, when clear, a disconnect is used. 4113** �E When operating in the PCI-X mode (with the exception of the MU queue ports at offsets 40h 4114** and 44h), when the transaction on the internal bus resulted in a target abort, the ATU generates 4115** a Split Completion Message (message class=2h - completer error, and message index=81h - 4116** internal bus target abort) to inform the requester about the abnormal condition. For the MU 4117** queue ports, the ATU returns either a target abort or a single data phase disconnect depending 4118** on the ATU ECC Target Abort Enable bit (bit 0 of the ATUIMR for ATU). The ITQ for this 4119** transaction is flushed. Refer to Section 3.7.1. 4120** �E When operating in the conventional PCI mode, when the transaction on the internal bus 4121** resulted in a master abort, the ATU returns a target abort to inform the requester about the 4122** abnormal condition. The ITQ for this transaction is flushed. Refer to Section 3.7.1 4123** �E When operating in the PCI-X mode, when the transaction on the internal bus resulted in a 4124** master abort, the ATU generates a Split Completion Message (message class=2h - completer 4125** error, and message index=80h - internal bus master abort) to inform the requester about the 4126** abnormal condition. The ITQ for this transaction is flushed. Refer to Section 3.7.1. 4127** �E When operating in the PCI-X mode, when the Split Completion transaction completes with 4128** either Master-Abort or Target-Abort, the requester is indicating a failure condition that 4129** prevents it from accepting the completion it requested. In this case, since the Split Request 4130** addresses a location that has no read side effects, the completer must discard the Split 4131** Completion and take no further action. 4132** The data flow for an inbound read transaction on the internal bus is summarized in the following 4133** statements: 4134** �E The ATU internal bus master interface requests the internal bus when a PCI address appears in 4135** an ITQ and transaction ordering has been satisfied. When operating in the PCI-X mode the 4136** ATU does not use the information provided by the Relax Ordering Attribute bit. That is, ATU 4137** always uses conventional PCI ordering rules. 4138** �E Once the internal bus is granted, the internal bus master interface drives the translated address 4139** onto the bus and wait for IB_DEVSEL#. When a Retry is signaled, the request is repeated. 4140** When a master abort occurs, the transaction is considered complete and a target abort is loaded 4141** into the associated IRQ for return to the PCI initiator (transaction is flushed once the PCI 4142** master has been delivered the target abort). 4143** �E Once the translated address is on the bus and the transaction has been accepted, the internal 4144** bus target starts returning data with the assertion of IB_TRDY#. Read data is continuously 4145** received by the IRQ until one of the following is true: 4146** �X The full byte count requested by the ATU read request is received. The ATU internal bus 4147** initiator interface performs a initiator completion in this case. 4148** �X When operating in the conventional PCI mode, a Target Abort is received on the internal 4149** bus from the internal bus target. In this case, the transaction is aborted and the PCI side is 4150** informed. 4151** �X When operating in the PCI-X mode, a Target Abort is received on the internal bus from 4152** the internal bus target. In this case, the transaction is aborted. The ATU generates a Split 4153** Completion Message (message class=2h - completer error, and message index=81h - 4154** target abort) on the PCI bus to inform the requester about the abnormal condition. The 4155** ITQ for this transaction is flushed. 4156** �X When operating in the conventional PCI mode, a single data phase disconnection is 4157** received from the internal bus target. When the data has not been received up to the next 4158** QWORD boundary, the ATU internal bus master interface attempts to reacquire the bus. 4159** When not, the bus returns to idle. 4160** �X When operating in the PCI-X mode, a single data phase disconnection is received from 4161** the internal bus target. The ATU IB initiator interface attempts to reacquire the bus to 4162** obtain remaining data. 4163** �X When operating in the conventional PCI mode, a disconnection at Next ADB is received 4164** from the internal bus target. The bus returns to idle. 4165** �X When operating in the PCI-X mode, a disconnection at Next ADB is received from the 4166** internal bus target. The ATU IB initiator interface attempts to reacquire the bus to obtain 4167** remaining data. 4168** To support PCI Local Bus Specification, Revision 2.0 devices, the ATU can be programmed to 4169** ignore the memory read command (Memory Read, Memory Read Line, and Memory Read 4170** Multiple) when trying to match the current inbound read transaction with data in a DRC queue 4171** which was read previously (DRC on target bus). When the Read Command Alias Bit in the 4172** ATUCR register is set, the ATU does not distinguish the read commands on transactions. For 4173** example, the ATU enqueues a DRR with a Memory Read Multiple command and performs the read 4174** on the internal bus. Some time later, a PCI master attempts a Memory Read with the same address 4175** as the previous Memory Read Multiple. When the Read Command Bit is set, the ATU would return 4176** the read data from the DRC queue and consider the Delayed Read transaction complete. When the 4177** Read Command bit in the ATUCR was clear, the ATU would not return data since the PCI read 4178** commands did not match, only the address. 4179************************************************************************** 4180*/ 4181/* 4182************************************************************************** 4183** Inbound Write Transaction 4184**======================================================================== 4185** An inbound write transaction is initiated by a PCI master and is targeted at either 80331 local 4186** memory or a 80331 memory-mapped register. 4187** Data flow for an inbound write transaction on the PCI bus is summarized as: 4188** �E The ATU claims the PCI write transaction when the PCI address is within the inbound 4189** translation window defined by the ATU Inbound Base Address Register (and Inbound Upper 4190** Base Address Register during DACs) and Inbound Limit Register. 4191** �E When the IWADQ has at least one address entry available and the IWQ has at least one buffer 4192** available, the address is captured and the first data phase is accepted. 4193** �E The PCI interface continues to accept write data until one of the following is true: 4194** �X The initiator performs a disconnect. 4195** �X The transaction crosses a buffer boundary. 4196** �E When an address parity error is detected during the address phase of the transaction, the 4197** address parity error mechanisms are used. Refer to Section 3.7.1 for details of the address 4198** parity error response. 4199** �E When operating in the PCI-X mode when an attribute parity error is detected, the attribute 4200** parity error mechanism described in Section 3.7.1 is used. 4201** �E When a data parity error is detected while accepting data, the slave interface sets the 4202** appropriate bits based on PCI specifications. No other action is taken. Refer to Section 3.7.2.6 4203** for details of the inbound write data parity error response. 4204** Once the PCI interface places a PCI address in the IWADQ, when IWQ has received data sufficient 4205** to cross a buffer boundary or the master disconnects on the PCI bus, the ATUs internal bus 4206** interface becomes aware of the inbound write. When there are additional write transactions ahead 4207** in the IWQ/IWADQ, the current transaction remains posted until ordering and priority have been 4208** satisfied (Refer to Section 3.5.3) and the transaction is attempted on the internal bus by the ATU 4209** internal master interface. The ATU does not insert target wait states nor do data merging on the PCI 4210** interface, when operating in the PCI mode. 4211** In the PCI-X mode memory writes are always executed as immediate transactions, while 4212** configuration write transactions are processed as split transactions. The ATU generates a Split 4213** Completion Message, (with Message class=0h - Write Completion Class and Message index = 4214** 00h - Write Completion Message) once a configuration write is successfully executed. 4215** Also, when operating in the PCI-X mode a write sequence may contain multiple write transactions. 4216** The ATU handles such transactions as independent transactions. 4217** Data flow for the inbound write transaction on the internal bus is summarized as: 4218** �E The ATU internal bus master requests the internal bus when IWADQ has at least one entry 4219** with associated data in the IWQ. 4220** �E When the internal bus is granted, the internal bus master interface initiates the write 4221** transaction by driving the translated address onto the internal bus. For details on inbound 4222** address translation. 4223** �E When IB_DEVSEL# is not returned, a master abort condition is signaled on the internal bus. 4224** The current transaction is flushed from the queue and SERR# may be asserted on the PCI 4225** interface. 4226** �E The ATU initiator interface asserts IB_REQ64# to attempt a 64-bit transfer. When 4227** IB_ACK64# is not returned, a 32-bit transfer is used. Transfers of less than 64-bits use the 4228** IB_C/BE[7:0]# to mask the bytes not written in the 64-bit data phase. Write data is transferred 4229** from the IWQ to the internal bus when data is available and the internal bus interface retains 4230** internal bus ownership. 4231** �E The internal bus interface stops transferring data from the current transaction to the internal 4232** bus when one of the following conditions becomes true: 4233** �X The internal bus initiator interface loses bus ownership. The ATU internal initiator 4234** terminates the transfer (initiator disconnection) at the next ADB (for the internal bus ADB 4235** is defined as a naturally aligned 128-byte boundary) and attempt to reacquire the bus to 4236** complete the delivery of remaining data using the same sequence ID but with the 4237** modified starting address and byte count. 4238** �X A Disconnect at Next ADB is signaled on the internal bus from the internal target. When 4239** the transaction in the IWQ completes at that ADB, the initiator returns to idle. When the 4240** transaction in the IWQ is not complete, the initiator attempts to reacquire the bus to 4241** complete the delivery of remaining data using the same sequence ID but with the 4242** modified starting address and byte count. 4243** �X A Single Data Phase Disconnect is signaled on the internal bus from the internal target. 4244** When the transaction in the IWQ needs only a single data phase, the master returns to idle. 4245** When the transaction in the IWQ is not complete, the initiator attempts to reacquire the 4246** bus to complete the delivery of remaining data using the same sequence ID but with the 4247** modified starting address and byte count. 4248** �X The data from the current transaction has completed (satisfaction of byte count). An 4249** initiator termination is performed and the bus returns to idle. 4250** �X A Master Abort is signaled on the internal bus. SERR# may be asserted on the PCI bus. 4251** Data is flushed from the IWQ. 4252***************************************************************** 4253*/ 4254 4255 4256 4257/* 4258************************************************************************** 4259** Inbound Read Completions Data Parity Errors 4260**======================================================================== 4261** As an initiator, the ATU may encounter this error condition when operating in the PCI-X mode. 4262** When as the completer of a Split Read Request the ATU observes PERR# assertion during the split 4263** completion transaction, the ATU attempts to complete the transaction normally and no further 4264** action is taken. 4265************************************************************************** 4266*/ 4267 4268/* 4269************************************************************************** 4270** Inbound Configuration Write Completion Message Data Parity Errors 4271**======================================================================== 4272** As an initiator, the ATU may encounter this error condition when operating in the PCI-X mode. 4273** When as the completer of a Configuration (Split) Write Request the ATU observes PERR# 4274** assertion during the split completion transaction, the ATU attempts to complete the transaction 4275** normally and no further action is taken. 4276************************************************************************** 4277*/ 4278 4279/* 4280************************************************************************** 4281** Inbound Read Request Data Parity Errors 4282**===================== Immediate Data Transfer ========================== 4283** As a target, the ATU may encounter this error when operating in the Conventional PCI or PCI-X modes. 4284** Inbound read data parity errors occur when read data delivered from the IRQ is detected as having 4285** bad parity by the initiator of the transaction who is receiving the data. The initiator may optionally 4286** report the error to the system by asserting PERR#. As a target device in this scenario, no action is 4287** required and no error bits are set. 4288**=====================Split Response Termination========================= 4289** As a target, the ATU may encounter this error when operating in the PCI-X mode. 4290** Inbound read data parity errors occur during the Split Response Termination. The initiator may 4291** optionally report the error to the system by asserting PERR#. As a target device in this scenario, no 4292** action is required and no error bits are set. 4293************************************************************************** 4294*/ 4295 4296/* 4297************************************************************************** 4298** Inbound Write Request Data Parity Errors 4299**======================================================================== 4300** As a target, the ATU may encounter this error when operating in the Conventional or PCI-X modes. 4301** Data parity errors occurring during write operations received by the ATU may assert PERR# on 4302** the PCI Bus. When an error occurs, the ATU continues accepting data until the initiator of the write 4303** transaction completes or a queue fill condition is reached. Specifically, the following actions with 4304** the given constraints are taken by the ATU: 4305** �E PERR# is asserted two clocks cycles (three clock cycles when operating in the PCI-X mode) 4306** following the data phase in which the data parity error is detected on the bus. This is only 4307** done when the Parity Error Response bit in the ATUCMD is set. 4308** �E The Detected Parity Error bit in the ATUSR is set. When the ATU sets this bit, additional 4309** actions is taken: 4310** �X When the ATU Detected Parity Error Interrupt Mask bit in the ATUIMR is clear, set the 4311** Detected Parity Error bit in the ATUISR. When set, no action. 4312*************************************************************************** 4313*/ 4314 4315 4316/* 4317*************************************************************************** 4318** Inbound Configuration Write Request 4319** ===================================================================== 4320** As a target, the ATU may encounter this error when operating in the Conventional or PCI-X modes. 4321** =============================================== 4322** Conventional PCI Mode 4323** =============================================== 4324** To allow for correct data parity calculations for delayed write transactions, the ATU delays the 4325** assertion of STOP# (signalling a Retry) until PAR is driven by the master. A parity error during a 4326** delayed write transaction (inbound configuration write cycle) can occur in any of the following 4327** parts of the transactions: 4328** �E During the initial Delayed Write Request cycle on the PCI bus when the ATU latches the 4329** address/command and data for delayed delivery to the internal configuration register. 4330** �E During the Delayed Write Completion cycle on the PCI bus when the ATU delivers the status 4331** of the operation back to the original master. 4332** The 80331 ATU PCI interface has the following responses to a delayed write parity error for 4333** inbound transactions during Delayed Write Request cycles with the given constraints: 4334** �E When the Parity Error Response bit in the ATUCMD is set, the ATU asserts TRDY# 4335** (disconnects with data) and two clock cycles later asserts PERR# notifying the initiator of the 4336** parity error. The delayed write cycle is not enqueued and forwarded to the internal bus. 4337** When the Parity Error Response bit in the ATUCMD is cleared, the ATU retries the 4338** transaction by asserting STOP# and enqueues the Delayed Write Request cycle to be 4339** forwarded to the internal bus. PERR# is not asserted. 4340** �E The Detected Parity Error bit in the ATUSR is set. When the ATU sets this bit, additional 4341** actions is taken: 4342** �X When the ATU Detected Parity Error Interrupt Mask bit in the ATUIMR is clear, set the 4343** Detected Parity Error bit in the ATUISR. When set, no action. 4344** For the original write transaction to be completed, the initiator retries the transaction on the PCI 4345** bus and the ATU returns the status from the internal bus, completing the transaction. 4346** For the Delayed Write Completion transaction on the PCI bus where a data parity error occurs and 4347** therefore does not agree with the status being returned from the internal bus (i.e. status being 4348** returned is normal completion) the ATU performs the following actions with the given constraints: 4349** �E When the Parity Error Response Bit is set in the ATUCMD, the ATU asserts TRDY# 4350** (disconnects with data) and two clocks later asserts PERR#. The Delayed Completion cycle in 4351** the IDWQ remains since the data of retried command did not match the data within the queue. 4352** �E The Detected Parity Error bit in the ATUSR is set. When the ATU sets this bit, additional 4353** actions is taken: 4354** �X When the ATU Detected Parity Error Interrupt Mask bit in the ATUIMR is clear, set the 4355** Detected Parity Error bit in the ATUISR. When set, no action. 4356** =================================================== 4357** PCI-X Mode 4358** =================================================== 4359** Data parity errors occurring during configuration write operations received by the ATU may cause 4360** PERR# assertion and delivery of a Split Completion Error Message on the PCI Bus. When an error 4361** occurs, the ATU accepts the write data and complete with a Split Response Termination. 4362** Specifically, the following actions with the given constraints are then taken by the ATU: 4363** �E When the Parity Error Response bit in the ATUCMD is set, PERR# is asserted three clocks 4364** cycles following the Split Response Termination in which the data parity error is detected on 4365** the bus. When the ATU asserts PERR#, additional actions is taken: 4366** �X A Split Write Data Parity Error message (with message class=2h - completer error and 4367** message index=01h - Split Write Data Parity Error) is initiated by the ATU on the PCI bus 4368** that addresses the requester of the configuration write. 4369** �X When the Initiated Split Completion Error Message Interrupt Mask in the ATUIMR is 4370** clear, set the Initiated Split Completion Error Message bit in the ATUISR. When set, no 4371** action. 4372** �X The Split Write Request is not enqueued and forwarded to the internal bus. 4373** �E The Detected Parity Error bit in the ATUSR is set. When the ATU sets this bit, additional 4374** actions is taken: 4375** �X When the ATU Detected Parity Error Interrupt Mask bit in the ATUIMR is clear, set the 4376** Detected Parity Error bit in the ATUISR. When set, no action. 4377** 4378*************************************************************************** 4379*/ 4380 4381/* 4382*************************************************************************** 4383** Split Completion Messages 4384** ======================================================================= 4385** As a target, the ATU may encounter this error when operating in the PCI-X mode. 4386** Data parity errors occurring during Split Completion Messages claimed by the ATU may assert 4387** PERR# (when enabled) or SERR# (when enabled) on the PCI Bus. When an error occurs, the 4388** ATU accepts the data and complete normally. Specifically, the following actions with the given 4389** constraints are taken by the ATU: 4390** �E PERR# is asserted three clocks cycles following the data phase in which the data parity error 4391** is detected on the bus. This is only done when the Parity Error Response bit in the ATUCMD 4392** is set. When the ATU asserts PERR#, additional actions is taken: 4393** �X The Master Parity Error bit in the ATUSR is set. 4394** �X When the ATU PCI Master Parity Error Interrupt Mask Bit in the ATUIMR is clear, set the 4395** PCI Master Parity Error bit in the ATUISR. When set, no action. 4396** �X When the SERR# Enable bit in the ATUCMD is set, and the Data Parity Error Recover 4397** Enable bit in the PCIXCMD register is clear, assert SERR#; otherwise no action is taken. 4398** When the ATU asserts SERR#, additional actions is taken: 4399** Set the SERR# Asserted bit in the ATUSR. 4400** When the ATU SERR# Asserted Interrupt Mask Bit in the ATUIMR is clear, set the 4401** SERR# Asserted bit in the ATUISR. When set, no action. 4402** When the ATU SERR# Detected Interrupt Enable Bit in the ATUCR is set, set the 4403** SERR# Detected bit in the ATUISR. When clear, no action. 4404** �E When the SCE bit (Split Completion Error -- bit 30 of the Completer Attributes) is set during 4405** the Attribute phase, the Received Split Completion Error Message bit in the PCIXSR is set. 4406** When the ATU sets this bit, additional actions is taken: 4407** �X When the ATU Received Split Completion Error Message Interrupt Mask bit in the 4408** ATUIMR is clear, set the Received Split Completion Error Message bit in the ATUISR. 4409** When set, no action. 4410** �E The Detected Parity Error bit in the ATUSR is set. When the ATU sets this bit, additional 4411** actions is taken: 4412** �X When the ATU Detected Parity Error Interrupt Mask bit in the ATUIMR is clear, set the 4413** Detected Parity Error bit in the ATUISR. When set, no action. 4414** �E The transaction associated with the Split Completion Message is discarded. 4415** �E When the discarded transaction was a read, a completion error message (with message 4416** class=2h - completer error and message index=82h - PCI bus read parity error) is generated on 4417** the internal bus of the 80331. 4418***************************************************************************** 4419*/ 4420 4421 4422/* 4423****************************************************************************************************** 4424** Messaging Unit (MU) of the Intel R 80331 I/O processor (80331) 4425** ================================================================================================== 4426** The Messaging Unit (MU) transfers data between the PCI system and the 80331 4427** notifies the respective system when new data arrives. 4428** The PCI window for messaging transactions is always the first 4 Kbytes of the inbound translation. 4429** window defined by: 4430** 1.Inbound ATU Base Address Register 0 (IABAR0) 4431** 2.Inbound ATU Limit Register 0 (IALR0) 4432** All of the Messaging Unit errors are reported in the same manner as ATU errors. 4433** Error conditions and status can be found in : 4434** 1.ATUSR 4435** 2.ATUISR 4436**==================================================================================================== 4437** Mechanism Quantity Assert PCI Interrupt Signals Generate I/O Processor Interrupt 4438**---------------------------------------------------------------------------------------------------- 4439** Message Registers 2 Inbound Optional Optional 4440** 2 Outbound 4441**---------------------------------------------------------------------------------------------------- 4442** Doorbell Registers 1 Inbound Optional Optional 4443** 1 Outbound 4444**---------------------------------------------------------------------------------------------------- 4445** Circular Queues 4 Circular Queues Under certain conditions Under certain conditions 4446**---------------------------------------------------------------------------------------------------- 4447** Index Registers 1004 32-bit Memory Locations No Optional 4448**==================================================================================================== 4449** PCI Memory Map: First 4 Kbytes of the ATU Inbound PCI Address Space 4450**==================================================================================================== 4451** 0000H Reserved 4452** 0004H Reserved 4453** 0008H Reserved 4454** 000CH Reserved 4455**------------------------------------------------------------------------ 4456** 0010H Inbound Message Register 0 ] 4457** 0014H Inbound Message Register 1 ] 4458** 0018H Outbound Message Register 0 ] 4459** 001CH Outbound Message Register 1 ] 4 Message Registers 4460**------------------------------------------------------------------------ 4461** 0020H Inbound Doorbell Register ] 4462** 0024H Inbound Interrupt Status Register ] 4463** 0028H Inbound Interrupt Mask Register ] 4464** 002CH Outbound Doorbell Register ] 4465** 0030H Outbound Interrupt Status Register ] 4466** 0034H Outbound Interrupt Mask Register ] 2 Doorbell Registers and 4 Interrupt Registers 4467**------------------------------------------------------------------------ 4468** 0038H Reserved 4469** 003CH Reserved 4470**------------------------------------------------------------------------ 4471** 0040H Inbound Queue Port ] 4472** 0044H Outbound Queue Port ] 2 Queue Ports 4473**------------------------------------------------------------------------ 4474** 0048H Reserved 4475** 004CH Reserved 4476**------------------------------------------------------------------------ 4477** 0050H ] 4478** : ] 4479** : Intel Xscale Microarchitecture Local Memory ] 4480** : ] 4481** 0FFCH ] 1004 Index Registers 4482******************************************************************************* 4483*/ 4484/* 4485***************************************************************************** 4486** Theory of MU Operation 4487***************************************************************************** 4488**-------------------- 4489** inbound_msgaddr0: 4490** inbound_msgaddr1: 4491** outbound_msgaddr0: 4492** outbound_msgaddr1: 4493** . The MU has four independent messaging mechanisms. 4494** There are four Message Registers that are similar to a combination of mailbox and doorbell registers. 4495** Each holds a 32-bit value and generates an interrupt when written. 4496**-------------------- 4497** inbound_doorbell: 4498** outbound_doorbell: 4499** . The two Doorbell Registers support software interrupts. 4500** When a bit is set in a Doorbell Register, an interrupt is generated. 4501**-------------------- 4502** inbound_queueport: 4503** outbound_queueport: 4504** 4505** 4506** . The Circular Queues support a message passing scheme that uses 4 circular queues. 4507** The 4 circular queues are implemented in 80331 local memory. 4508** Two queues are used for inbound messages and two are used for outbound messages. 4509** Interrupts may be generated when the queue is written. 4510**-------------------- 4511** local_buffer 0x0050 ....0x0FFF 4512** . The Index Registers use a portion of the 80331 local memory to implement a large set of message registers. 4513** When one of the Index Registers is written, an interrupt is generated and the address of the register written is captured. 4514** Interrupt status for all interrupts is recorded in the Inbound Interrupt Status Register and the Outbound Interrupt Status Register. 4515** Each interrupt generated by the Messaging Unit can be masked. 4516**-------------------- 4517** . Multi-DWORD PCI burst accesses are not supported by the Messaging Unit, 4518** with the exception of Multi-DWORD reads to the index registers. 4519** In Conventional mode: the MU terminates Multi-DWORD PCI transactions 4520** (other than index register reads) with a disconnect at the next Qword boundary, with the exception of queue ports. 4521** In PCI-X mode : the MU terminates a Multi-DWORD PCI read transaction with a Split Response 4522** and the data is returned through split completion transaction(s). 4523** however, when the burst request crosses into or through the range of offsets 40h to 4Ch 4524** (e.g., this includes the queue ports) the transaction is signaled target-abort immediately on the PCI bus. 4525** In PCI-X mode, Multi-DWORD PCI writes is signaled a Single-Data-Phase Disconnect 4526** which means that no data beyond the first Qword (Dword when the MU does not assert P_ACK64#) is written. 4527**-------------------- 4528** . All registers needed to configure and control the Messaging Unit are memory-mapped registers. 4529** The MU uses the first 4 Kbytes of the inbound translation window in the Address Translation Unit (ATU). 4530** This PCI address window is used for PCI transactions that access the 80331 local memory. 4531** The PCI address of the inbound translation window is contained in the Inbound ATU Base Address Register. 4532**-------------------- 4533** . From the PCI perspective, the Messaging Unit is part of the Address Translation Unit. 4534** The Messaging Unit uses the PCI configuration registers of the ATU for control and status information. 4535** The Messaging Unit must observe all PCI control bits in the ATU Command Register and ATU Configuration Register. 4536** The Messaging Unit reports all PCI errors in the ATU Status Register. 4537**-------------------- 4538** . Parts of the Messaging Unit can be accessed as a 64-bit PCI device. 4539** The register interface, message registers, doorbell registers, 4540** and index registers returns a P_ACK64# in response to a P_REQ64# on the PCI interface. 4541** Up to 1 Qword of data can be read or written per transaction (except Index Register reads). 4542** The Inbound and Outbound Queue Ports are always 32-bit addresses and the MU does not assert P_ACK64# to offsets 40H and 44H. 4543************************************************************************** 4544*/ 4545/* 4546************************************************************************** 4547** Message Registers 4548** ============================== 4549** . Messages can be sent and received by the 80331 through the use of the Message Registers. 4550** . When written, the message registers may cause an interrupt to be generated to either the Intel XScale core or the host processor. 4551** . Inbound messages are sent by the host processor and received by the 80331. 4552** Outbound messages are sent by the 80331 and received by the host processor. 4553** . The interrupt status for outbound messages is recorded in the Outbound Interrupt Status Register. 4554** Interrupt status for inbound messages is recorded in the Inbound Interrupt Status Register. 4555** 4556** Inbound Messages: 4557** ----------------- 4558** . When an inbound message register is written by an external PCI agent, an interrupt may be generated to the Intel XScale core. 4559** . The interrupt may be masked by the mask bits in the Inbound Interrupt Mask Register. 4560** . The Intel XScale core interrupt is recorded in the Inbound Interrupt Status Register. 4561** The interrupt causes the Inbound Message Interrupt bit to be set in the Inbound Interrupt Status Register. 4562** This is a Read/Clear bit that is set by the MU hardware and cleared by software. 4563** The interrupt is cleared when the Intel XScale core writes a value of 4564** 1 to the Inbound Message Interrupt bit in the Inbound Interrupt Status Register. 4565** ------------------------------------------------------------------------ 4566** Inbound Message Register - IMRx 4567** 4568** . There are two Inbound Message Registers: IMR0 and IMR1. 4569** . When the IMR register is written, an interrupt to the Intel XScale core may be generated. 4570** The interrupt is recorded in the Inbound Interrupt Status Register and may be masked 4571** by the Inbound Message Interrupt Mask bit in the Inbound Interrupt Mask Register. 4572** ----------------------------------------------------------------- 4573** Bit Default Description 4574** 31:00 0000 0000H Inbound Message - This is a 32-bit message written by an external PCI agent. 4575** When written, an interrupt to the Intel XScale core may be generated. 4576************************************************************************** 4577*/ 4578#define ARCMSR_MU_INBOUND_MESSAGE_REG0 0x10 /*dword 0x13,0x12,0x11,0x10*/ 4579#define ARCMSR_MU_INBOUND_MESSAGE_REG1 0x14 /*dword 0x17,0x16,0x15,0x14*/ 4580/* 4581************************************************************************** 4582** Outbound Message Register - OMRx 4583** -------------------------------- 4584** There are two Outbound Message Registers: OMR0 and OMR1. When the OMR register is 4585** written, a PCI interrupt may be generated. The interrupt is recorded in the Outbound Interrupt 4586** Status Register and may be masked by the Outbound Message Interrupt Mask bit in the Outbound 4587** Interrupt Mask Register. 4588** 4589** Bit Default Description 4590** 31:00 00000000H Outbound Message - This is 32-bit message written by the Intel XScale core. When written, an 4591** interrupt may be generated on the PCI Interrupt pin determined by the ATU Interrupt Pin Register. 4592************************************************************************** 4593*/ 4594#define ARCMSR_MU_OUTBOUND_MESSAGE_REG0 0x18 /*dword 0x1B,0x1A,0x19,0x18*/ 4595#define ARCMSR_MU_OUTBOUND_MESSAGE_REG1 0x1C /*dword 0x1F,0x1E,0x1D,0x1C*/ 4596/* 4597************************************************************************** 4598** Doorbell Registers 4599** ============================== 4600** There are two Doorbell Registers: 4601** Inbound Doorbell Register 4602** Outbound Doorbell Register 4603** The Inbound Doorbell Register allows external PCI agents to generate interrupts to the Intel R XScale core. 4604** The Outbound Doorbell Register allows the Intel R XScale core to generate a PCI interrupt. 4605** Both Doorbell Registers may generate interrupts whenever a bit in the register is set. 4606** 4607** Inbound Doorbells: 4608** ------------------ 4609** . When the Inbound Doorbell Register is written by an external PCI agent, an interrupt may be generated to the Intel R XScale core. 4610** An interrupt is generated when any of the bits in the doorbell register is written to a value of 1. 4611** Writing a value of 0 to any bit does not change the value of that bit and does not cause an interrupt to be generated. 4612** . Once a bit is set in the Inbound Doorbell Register, it cannot be cleared by any external PCI agent. 4613** The interrupt is recorded in the Inbound Interrupt Status Register. 4614** . The interrupt may be masked by the Inbound Doorbell Interrupt mask bit in the Inbound Interrupt Mask Register. 4615** When the mask bit is set for a particular bit, no interrupt is generated for that bit. 4616** The Inbound Interrupt Mask Register affects only the generation of the normal messaging unit interrupt 4617** and not the values written to the Inbound Doorbell Register. 4618** One bit in the Inbound Doorbell Register is reserved for an Error Doorbell interrupt. 4619** . The interrupt is cleared when the Intel R XScale core writes a value of 1 to the bits in the Inbound Doorbell Register that are set. 4620** Writing a value of 0 to any bit does not change the value of that bit and does not clear the interrupt. 4621** ------------------------------------------------------------------------ 4622** Inbound Doorbell Register - IDR 4623** 4624** . The Inbound Doorbell Register (IDR) is used to generate interrupts to the Intel XScale core. 4625** . Bit 31 is reserved for generating an Error Doorbell interrupt. 4626** When bit 31 is set, an Error interrupt may be generated to the Intel XScale core. 4627** All other bits, when set, cause the Normal Messaging Unit interrupt line of the Intel XScale core to be asserted, 4628** when the interrupt is not masked by the Inbound Doorbell Interrupt Mask bit in the Inbound Interrupt Mask Register. 4629** The bits in the IDR register can only be set by an external PCI agent and can only be cleared by the Intel XScale core. 4630** ------------------------------------------------------------------------ 4631** Bit Default Description 4632** 31 0 2 Error Interrupt - Generate an Error Interrupt to the Intel XScale core. 4633** 30:00 00000000H Normal Interrupt - When any bit is set, generate a Normal interrupt to the Intel XScale core. 4634** When all bits are clear, do not generate a Normal Interrupt. 4635************************************************************************** 4636*/ 4637#define ARCMSR_MU_INBOUND_DOORBELL_REG 0x20 /*dword 0x23,0x22,0x21,0x20*/ 4638/* 4639************************************************************************** 4640** Inbound Interrupt Status Register - IISR 4641** 4642** . The Inbound Interrupt Status Register (IISR) contains hardware interrupt status. 4643** It records the status of Intel XScale core interrupts generated by the Message Registers, Doorbell Registers, and the Circular Queues. 4644** All interrupts are routed to the Normal Messaging Unit interrupt input of the Intel XScale core, 4645** except for the Error Doorbell Interrupt and the Outbound Free Queue Full interrupt; 4646** these two are routed to the Messaging Unit Error interrupt input. 4647** The generation of interrupts recorded in the Inbound Interrupt Status Register 4648** may be masked by setting the corresponding bit in the Inbound Interrupt Mask Register. 4649** Some of the bits in this register are Read Only. 4650** For those bits, the interrupt must be cleared through another register. 4651** 4652** Bit Default Description 4653** 31:07 0000000H 0 2 Reserved 4654** 06 0 2 Index Register Interrupt - This bit is set by the MU hardware 4655** when an Index Register has been written after a PCI transaction. 4656** 05 0 2 Outbound Free Queue Full Interrupt - This bit is set 4657** when the Outbound Free Head Pointer becomes equal to the Tail Pointer and the queue is full. 4658** An Error interrupt is generated for this condition. 4659** 04 0 2 Inbound Post Queue Interrupt - This bit is set by the MU hardware when the Inbound Post Queue has been written. 4660** Once cleared, an interrupt does NOT be generated 4661** when the head and tail pointers remain unequal (i.e. queue status is Not Empty). 4662** Therefore, when software leaves any unprocessed messages in the post queue when the interrupt is cleared, 4663** software must retain the information that the Inbound Post queue status is not empty. 4664** NOTE: This interrupt is provided with dedicated support in the 80331 Interrupt Controller. 4665** 03 0 2 Error Doorbell Interrupt - This bit is set when the Error Interrupt of the Inbound Doorbell Register is set. 4666** To clear this bit (and the interrupt), the Error Interrupt bit of the Inbound Doorbell Register must be clear. 4667** 02 0 2 Inbound Doorbell Interrupt - This bit is set when at least one 4668** Normal Interrupt bit in the Inbound Doorbell Register is set. 4669** To clear this bit (and the interrupt), the Normal Interrupt bits in the Inbound Doorbell Register must all be clear. 4670** 01 0 2 Inbound Message 1 Interrupt - This bit is set by the MU hardware when the Inbound Message 1 Register has been written. 4671** 00 0 2 Inbound Message 0 Interrupt - This bit is set by the MU hardware when the Inbound Message 0 Register has been written. 4672************************************************************************** 4673*/ 4674#define ARCMSR_MU_INBOUND_INTERRUPT_STATUS_REG 0x24 /*dword 0x27,0x26,0x25,0x24*/ 4675#define ARCMSR_MU_INBOUND_INDEX_INT 0x40 4676#define ARCMSR_MU_INBOUND_QUEUEFULL_INT 0x20 4677#define ARCMSR_MU_INBOUND_POSTQUEUE_INT 0x10 4678#define ARCMSR_MU_INBOUND_ERROR_DOORBELL_INT 0x08 4679#define ARCMSR_MU_INBOUND_DOORBELL_INT 0x04 4680#define ARCMSR_MU_INBOUND_MESSAGE1_INT 0x02 4681#define ARCMSR_MU_INBOUND_MESSAGE0_INT 0x01 4682/* 4683************************************************************************** 4684** Inbound Interrupt Mask Register - IIMR 4685** 4686** . The Inbound Interrupt Mask Register (IIMR) provides the ability to mask Intel XScale core interrupts generated by the Messaging Unit. 4687** Each bit in the Mask register corresponds to an interrupt bit in the Inbound Interrupt Status Register. 4688** Setting or clearing bits in this register does not affect the Inbound Interrupt Status Register. 4689** They only affect the generation of the Intel XScale core interrupt. 4690** ------------------------------------------------------------------------ 4691** Bit Default Description 4692** 31:07 000000H 0 2 Reserved 4693** 06 0 2 Index Register Interrupt Mask - When set, this bit masks the interrupt generated by the MU hardware 4694** when an Index Register has been written after a PCI transaction. 4695** 05 0 2 Outbound Free Queue Full Interrupt Mask - When set, this bit masks the Error interrupt generated 4696** when the Outbound Free Head Pointer becomes equal to the Tail Pointer and the queue is full. 4697** 04 0 2 Inbound Post Queue Interrupt Mask - When set, this bit masks the interrupt generated 4698** by the MU hardware when the Inbound Post Queue has been written. 4699** 03 0 2 Error Doorbell Interrupt Mask - When set, this bit masks the Error Interrupt 4700** when the Error Interrupt bit of the Inbound Doorbell Register is set. 4701** 02 0 2 Inbound Doorbell Interrupt Mask - When set, this bit masks the interrupt generated 4702** when at least one Normal Interrupt bit in the Inbound Doorbell Register is set. 4703** 01 0 2 Inbound Message 1 Interrupt Mask - When set, this bit masks the Inbound Message 1 4704** Interrupt generated by a write to the Inbound Message 1 Register. 4705** 00 0 2 Inbound Message 0 Interrupt Mask - When set, 4706** this bit masks the Inbound Message 0 Interrupt generated by a write to the Inbound Message 0 Register. 4707************************************************************************** 4708*/ 4709#define ARCMSR_MU_INBOUND_INTERRUPT_MASK_REG 0x28 /*dword 0x2B,0x2A,0x29,0x28*/ 4710#define ARCMSR_MU_INBOUND_INDEX_INTMASKENABLE 0x40 4711#define ARCMSR_MU_INBOUND_QUEUEFULL_INTMASKENABLE 0x20 4712#define ARCMSR_MU_INBOUND_POSTQUEUE_INTMASKENABLE 0x10 4713#define ARCMSR_MU_INBOUND_DOORBELL_ERROR_INTMASKENABLE 0x08 4714#define ARCMSR_MU_INBOUND_DOORBELL_INTMASKENABLE 0x04 4715#define ARCMSR_MU_INBOUND_MESSAGE1_INTMASKENABLE 0x02 4716#define ARCMSR_MU_INBOUND_MESSAGE0_INTMASKENABLE 0x01 4717/* 4718************************************************************************** 4719** Outbound Doorbell Register - ODR 4720** 4721** The Outbound Doorbell Register (ODR) allows software interrupt generation. It allows the Intel 4722** XScale core to generate PCI interrupts to the host processor by writing to this register. The 4723** generation of PCI interrupts through the Outbound Doorbell Register may be masked by setting the 4724** Outbound Doorbell Interrupt Mask bit in the Outbound Interrupt Mask Register. 4725** The Software Interrupt bits in this register can only be set by the Intel XScale core and can only 4726** be cleared by an external PCI agent. 4727** ---------------------------------------------------------------------- 4728** Bit Default Description 4729** 31 0 2 Reserved 4730** 30 0 2 Reserved. 4731** 29 0 2 Reserved 4732** 28 0000 0000H PCI Interrupt - When set, this bit causes the P_INTC# interrupt output 4733** (P_INTA# with BRG_EN and ARB_EN straps low) 4734** signal to be asserted or a Message-signaled Interrupt is generated (when enabled). 4735** When this bit is cleared, the P_INTC# interrupt output 4736** (P_INTA# with BRG_EN and ARB_EN straps low) 4737** signal is deasserted. 4738** 27:00 000 0000H Software Interrupts - When any bit is set the P_INTC# interrupt output 4739** (P_INTA# with BRG_EN and ARB_EN straps low) 4740** signal is asserted or a Message-signaled Interrupt is generated (when enabled). 4741** When all bits are cleared, the P_INTC# interrupt output (P_INTA# with BRG_EN and ARB_EN straps low) 4742** signal is deasserted. 4743************************************************************************** 4744*/ 4745#define ARCMSR_MU_OUTBOUND_DOORBELL_REG 0x2C /*dword 0x2F,0x2E,0x2D,0x2C*/ 4746/* 4747************************************************************************** 4748** Outbound Interrupt Status Register - OISR 4749** 4750** The Outbound Interrupt Status Register (OISR) contains hardware interrupt status. It records the 4751** status of PCI interrupts generated by the Message Registers, Doorbell Registers, and the Circular 4752** Queues. The generation of PCI interrupts recorded in the Outbound Interrupt Status Register may 4753** be masked by setting the corresponding bit in the Outbound Interrupt Mask Register. Some of the 4754** bits in this register are Read Only. For those bits, the interrupt must be cleared through another 4755** register. 4756** ---------------------------------------------------------------------- 4757** Bit Default Description 4758** 31:05 000000H 000 2 Reserved 4759** 04 0 2 PCI Interrupt - This bit is set when the PCI Interrupt bit (bit 28) is set in the Outbound Doorbell Register. 4760** To clear this bit (and the interrupt), the PCI Interrupt bit must be cleared. 4761** 03 0 2 Outbound Post Queue Interrupt - This bit is set when data in the prefetch buffer is valid. This bit is 4762** cleared when any prefetch data has been read from the Outbound Queue Port. 4763** 02 0 2 Outbound Doorbell Interrupt - This bit is set when at least one Software Interrupt bit in the Outbound 4764** Doorbell Register is set. To clear this bit (and the interrupt), the Software Interrupt bits in the Outbound 4765** Doorbell Register must all be clear. 4766** 01 0 2 Outbound Message 1 Interrupt - This bit is set by the MU when the Outbound Message 1 Register is 4767** written. Clearing this bit clears the interrupt. 4768** 00 0 2 Outbound Message 0 Interrupt - This bit is set by the MU when the Outbound Message 0 Register is 4769** written. Clearing this bit clears the interrupt. 4770************************************************************************** 4771*/ 4772#define ARCMSR_MU_OUTBOUND_INTERRUPT_STATUS_REG 0x30 /*dword 0x33,0x32,0x31,0x30*/ 4773#define ARCMSR_MU_OUTBOUND_PCI_INT 0x10 4774#define ARCMSR_MU_OUTBOUND_POSTQUEUE_INT 0x08 4775#define ARCMSR_MU_OUTBOUND_DOORBELL_INT 0x04 4776#define ARCMSR_MU_OUTBOUND_MESSAGE1_INT 0x02 4777#define ARCMSR_MU_OUTBOUND_MESSAGE0_INT 0x01 4778/* 4779************************************************************************** 4780** Outbound Interrupt Mask Register - OIMR 4781** The Outbound Interrupt Mask Register (OIMR) provides the ability to mask outbound PCI 4782** interrupts generated by the Messaging Unit. Each bit in the mask register corresponds to a 4783** hardware interrupt bit in the Outbound Interrupt Status Register. When the bit is set, the PCI 4784** interrupt is not generated. When the bit is clear, the interrupt is allowed to be generated. 4785** Setting or clearing bits in this register does not affect the Outbound Interrupt Status Register. They 4786** only affect the generation of the PCI interrupt. 4787** ---------------------------------------------------------------------- 4788** Bit Default Description 4789** 31:05 000000H Reserved 4790** 04 0 2 PCI Interrupt Mask - When set, this bit masks the interrupt generation when the PCI Interrupt bit (bit 28) 4791** in the Outbound Doorbell Register is set. 4792** 03 0 2 Outbound Post Queue Interrupt Mask - When set, this bit masks the interrupt generated when data in 4793** the prefetch buffer is valid. 4794** 02 0 2 Outbound Doorbell Interrupt Mask - When set, this bit masks the interrupt generated by the Outbound 4795** Doorbell Register. 4796** 01 0 2 Outbound Message 1 Interrupt Mask - When set, this bit masks the Outbound Message 1 Interrupt 4797** generated by a write to the Outbound Message 1 Register. 4798** 00 0 2 Outbound Message 0 Interrupt Mask- When set, this bit masks the Outbound Message 0 Interrupt 4799** generated by a write to the Outbound Message 0 Register. 4800************************************************************************** 4801*/ 4802#define ARCMSR_MU_OUTBOUND_INTERRUPT_MASK_REG 0x34 /*dword 0x37,0x36,0x35,0x34*/ 4803#define ARCMSR_MU_OUTBOUND_PCI_INTMASKENABLE 0x10 4804#define ARCMSR_MU_OUTBOUND_POSTQUEUE_INTMASKENABLE 0x08 4805#define ARCMSR_MU_OUTBOUND_DOORBELL_INTMASKENABLE 0x04 4806#define ARCMSR_MU_OUTBOUND_MESSAGE1_INTMASKENABLE 0x02 4807#define ARCMSR_MU_OUTBOUND_MESSAGE0_INTMASKENABLE 0x01 4808#define ARCMSR_MU_OUTBOUND_ALL_INTMASKENABLE 0x1F 4809/* 4810************************************************************************** 4811** 4812************************************************************************** 4813*/ 4814#define ARCMSR_MU_INBOUND_QUEUE_PORT_REG 0x40 /*dword 0x43,0x42,0x41,0x40*/ 4815#define ARCMSR_MU_OUTBOUND_QUEUE_PORT_REG 0x44 /*dword 0x47,0x46,0x45,0x44*/ 4816/* 4817************************************************************************** 4818** Circular Queues 4819** ====================================================================== 4820** The MU implements four circular queues. There are 2 inbound queues and 2 outbound queues. In 4821** this case, inbound and outbound refer to the direction of the flow of posted messages. 4822** Inbound messages are either: 4823** �E posted messages by other processors for the Intel XScale core to process or 4824** �E free (or empty) messages that can be reused by other processors. 4825** Outbound messages are either: 4826** �E posted messages by the Intel XScale core for other processors to process or 4827** �E free (or empty) messages that can be reused by the Intel XScale core. 4828** Therefore, free inbound messages flow away from the 80331 and free outbound messages flow toward the 80331. 4829** The four Circular Queues are used to pass messages in the following manner. 4830** . The two inbound queues are used to handle inbound messages 4831** and the two outbound queues are used to handle outbound messages. 4832** . One of the inbound queues is designated the Free queue and it contains inbound free messages. 4833** The other inbound queue is designated the Post queue and it contains inbound posted messages. 4834** Similarly, one of the outbound queues is designated the Free queue and the other outbound queue is designated the Post queue. 4835** 4836** ============================================================================================================= 4837** Circular Queue Summary 4838** _____________________________________________________________________________________________________________ 4839** | Queue Name | Purpose | Action on PCI Interface| 4840** |______________________|____________________________________________________________|_________________________| 4841** |Inbound Post Queue | Queue for inbound messages from other processors | Written | 4842** | | waiting to be processed by the 80331 | | 4843** |Inbound Free Queue | Queue for empty inbound messages from the 80331 | Read | 4844** | | available for use by other processors | | 4845** |Outbound Post Queue | Queue for outbound messages from the 80331 | Read | 4846** | | that are being posted to the other processors | | 4847** |Outbound Free Queue | Queue for empty outbound messages from other processors | Written | 4848** | | available for use by the 80331 | | 4849** |______________________|____________________________________________________________|_________________________| 4850** 4851** . The two inbound queues allow the host processor to post inbound messages for the 80331 in one 4852** queue and to receive free messages returning from the 80331. 4853** The host processor posts inbound messages, 4854** the Intel XScale core receives the posted message and when it is finished with the message, 4855** places it back on the inbound free queue for reuse by the host processor. 4856** 4857** The circular queues are accessed by external PCI agents through two port locations in the PCI 4858** address space: 4859** Inbound Queue Port 4860** and Outbound Queue Port. 4861** The Inbound Queue Port is used by external PCI agents to read the Inbound Free Queue and write the Inbound Post Queue. 4862** The Outbound Queue Port is used by external PCI agents to read the Outbound Post Queue and write the Outbound Free Queue. 4863** Note that a PCI transaction to the inbound or outbound queue ports with null byte enables (P_C/BE[3:0]#=1111 2 ) 4864** does not cause the MU hardware to increment the queue pointers. 4865** This is treated as when the PCI transaction did not occur. 4866** The Inbound and Outbound Queue Ports never respond with P_ACK64# on the PCI interface. 4867** ====================================================================================== 4868** Overview of Circular Queue Operation 4869** ====================================================================================== 4870** . The data storage for the circular queues must be provided by the 80331 local memory. 4871** . The base address of the circular queues is contained in the Queue Base Address Register. 4872** Each entry in the queue is a 32-bit data value. 4873** . Each read from or write to the queue may access only one queue entry. 4874** . Multi-DWORD accesses to the circular queues are not allowed. 4875** Sub-DWORD accesses are promoted to DWORD accesses. 4876** . Each circular queue has a head pointer and a tail pointer. 4877** The pointers are offsets from the Queue Base Address. 4878** . Writes to a queue occur at the head of the queue and reads occur from the tail. 4879** The head and tail pointers are incremented by either the Intel XScale core or the Messaging Unit hardware. 4880** Which unit maintains the pointer is determined by the writer of the queue. 4881** More details about the pointers are given in the queue descriptions below. 4882** The pointers are incremented after the queue access. 4883** Both pointers wrap around to the first address of the circular queue when they reach the circular queue size. 4884** 4885** Messaging Unit... 4886** 4887** The Messaging Unit generates an interrupt to the Intel XScale core or generate a PCI interrupt under certain conditions. 4888** . In general, when a Post queue is written, an interrupt is generated to notify the receiver that a message was posted. 4889** The size of each circular queue can range from 4K entries (16 Kbytes) to 64K entries (256 Kbytes). 4890** . All four queues must be the same size and may be contiguous. 4891** Therefore, the total amount of local memory needed by the circular queues ranges from 64 Kbytes to 1 Mbytes. 4892** The Queue size is determined by the Queue Size field in the MU Configuration Register. 4893** . There is one base address for all four queues. 4894** It is stored in the Queue Base Address Register (QBAR). 4895** The starting addresses of each queue is based on the Queue Base Address and the Queue Size field. 4896** here shows an example of how the circular queues should be set up based on the 4897** Intelligent I/O (I 2 O) Architecture Specification. 4898** Other ordering of the circular queues is possible. 4899** 4900** Queue Starting Address 4901** Inbound Free Queue QBAR 4902** Inbound Post Queue QBAR + Queue Size 4903** Outbound Post Queue QBAR + 2 * Queue Size 4904** Outbound Free Queue QBAR + 3 * Queue Size 4905** =================================================================================== 4906** Inbound Post Queue 4907** ------------------ 4908** The Inbound Post Queue holds posted messages placed there by other processors for the Intel XScale core to process. 4909** This queue is read from the queue tail by the Intel XScale core. It is written to the queue head by external PCI agents. 4910** The tail pointer is maintained by the Intel XScale core. The head pointer is maintained by the MU hardware. 4911** For a PCI write transaction that accesses the Inbound Queue Port, 4912** the MU writes the data to the local memory location address in the Inbound Post Head Pointer Register. 4913** When the data written to the Inbound Queue Port is written to local memory, the MU hardware increments the Inbound Post Head Pointer Register. 4914** An Intel XScale core interrupt may be generated when the Inbound Post Queue is written. 4915** The Inbound Post Queue Interrupt bit in the Inbound Interrupt Status Register indicates the interrupt status. 4916** The interrupt is cleared when the Inbound Post Queue Interrupt bit is cleared. 4917** The interrupt can be masked by the Inbound Interrupt Mask Register. 4918** Software must be aware of the state of the Inbound Post Queue Interrupt Mask bit to guarantee 4919** that the full condition is recognized by the core processor. 4920** In addition, to guarantee that the queue does not get overwritten, 4921** software must process messages from the tail of the queue before incrementing the tail pointer and clearing this interrupt. 4922** Once cleared, an interrupt is NOT generated when the head and tail pointers remain unequal (i.e. queue status is Not Empty). 4923** Only a new message posting the in the inbound queue generates a new interrupt. 4924** Therefore, when software leaves any unprocessed messages in the post queue when the interrupt is cleared, 4925** software must retain the information that the Inbound Post queue status. 4926** From the time that the PCI write transaction is received until the data is written 4927** in local memory and the Inbound Post Head Pointer Register is incremented, 4928** any PCI transaction that attempts to access the Inbound Post Queue Port is signalled a Retry. 4929** The Intel XScale core may read messages from the Inbound Post Queue 4930** by reading the data from the local memory location pointed to by the Inbound Post Tail Pointer Register. 4931** The Intel XScale core must then increment the Inbound Post Tail Pointer Register. 4932** When the Inbound Post Queue is full (head and tail pointers are equal and the head pointer was last updated by hardware), 4933** the hardware retries any PCI writes until a slot in the queue becomes available. 4934** A slot in the post queue becomes available by the Intel XScale core incrementing the tail pointer. 4935** =================================================================================== 4936** Inbound Free Queue 4937** ------------------ 4938** The Inbound Free Queue holds free inbound messages placed there by the Intel XScale core for other processors to use. 4939** This queue is read from the queue tail by external PCI agents. 4940** It is written to the queue head by the Intel XScale core. 4941** The tail pointer is maintained by the MU hardware. 4942** The head pointer is maintained by the Intel XScale core. 4943** For a PCI read transaction that accesses the Inbound Queue Port, 4944** the MU attempts to read the data at the local memory address in the Inbound Free Tail Pointer. 4945** When the queue is not empty (head and tail pointers are not equal) 4946** or full (head and tail pointers are equal but the head pointer was last written by software), the data is returned. 4947** When the queue is empty (head and tail pointers are equal and the head pointer was last updated by hardware), 4948** the value of -1 (FFFF.FFFFH) is returned. 4949** When the queue was not empty and the MU succeeded in returning the data at the tail, 4950** the MU hardware must increment the value in the Inbound Free Tail Pointer Register. 4951** To reduce latency for the PCI read access, the MU implements a prefetch mechanism to anticipate accesses to the Inbound Free Queue. 4952** The MU hardware prefetches the data at the tail of the Inbound Free Queue and load it into an internal prefetch register. 4953** When the PCI read access occurs, the data is read directly from the prefetch register. 4954** The prefetch mechanism loads a value of -1 (FFFF.FFFFH) into the prefetch register 4955** when the head and tail pointers are equal and the queue is empty. 4956** In order to update the prefetch register when messages are added to the queue and it becomes non-empty, 4957** the prefetch mechanism automatically starts a prefetch when the prefetch register contains FFFF.FFFFH 4958** and the Inbound Free Head Pointer Register is written. 4959** The Intel XScale core needs to update the Inbound Free Head Pointer Register when it adds messages to the queue. 4960** A prefetch must appear atomic from the perspective of the external PCI agent. 4961** When a prefetch is started, any PCI transaction that attempts to access the Inbound Free Queue is signalled a Retry until the prefetch is completed. 4962** The Intel XScale core may place messages in the Inbound Free Queue by writing the data to the 4963** local memory location pointed to by the Inbound Free Head Pointer Register. 4964** The processor must then increment the Inbound Free Head Pointer Register. 4965** ================================================================================== 4966** Outbound Post Queue 4967** ------------------- 4968** The Outbound Post Queue holds outbound posted messages placed there by the Intel XScale 4969** core for other processors to process. This queue is read from the queue tail by external PCI agents. 4970** It is written to the queue head by the Intel XScale core. The tail pointer is maintained by the 4971** MU hardware. The head pointer is maintained by the Intel XScale core. 4972** For a PCI read transaction that accesses the Outbound Queue Port, the MU attempts to read the 4973** data at the local memory address in the Outbound Post Tail Pointer Register. When the queue is not 4974** empty (head and tail pointers are not equal) or full (head and tail pointers are equal but the head 4975** pointer was last written by software), the data is returned. When the queue is empty (head and tail 4976** pointers are equal and the head pointer was last updated by hardware), the value of -1 4977** (FFFF.FFFFH) is returned. When the queue was not empty and the MU succeeded in returning the 4978** data at the tail, the MU hardware must increment the value in the Outbound Post Tail Pointer 4979** Register. 4980** To reduce latency for the PCI read access, the MU implements a prefetch mechanism to anticipate 4981** accesses to the Outbound Post Queue. The MU hardware prefetches the data at the tail of the 4982** Outbound Post Queue and load it into an internal prefetch register. When the PCI read access 4983** occurs, the data is read directly from the prefetch register. 4984** The prefetch mechanism loads a value of -1 (FFFF.FFFFH) into the prefetch register when the head 4985** and tail pointers are equal and the queue is empty. In order to update the prefetch register when 4986** messages are added to the queue and it becomes non-empty, the prefetch mechanism automatically 4987** starts a prefetch when the prefetch register contains FFFF.FFFFH and the Outbound Post Head 4988** Pointer Register is written. The Intel XScale core needs to update the Outbound Post Head 4989** Pointer Register when it adds messages to the queue. 4990** A prefetch must appear atomic from the perspective of the external PCI agent. When a prefetch is 4991** started, any PCI transaction that attempts to access the Outbound Post Queue is signalled a Retry 4992** until the prefetch is completed. 4993** A PCI interrupt may be generated when data in the prefetch buffer is valid. When the prefetch 4994** queue is clear, no interrupt is generated. The Outbound Post Queue Interrupt bit in the Outbound 4995** Interrupt Status Register shall indicate the status of the prefetch buffer data and therefore the 4996** interrupt status. The interrupt is cleared when any prefetched data has been read from the Outbound 4997** Queue Port. The interrupt can be masked by the Outbound Interrupt Mask Register. 4998** The Intel XScale core may place messages in the Outbound Post Queue by writing the data to 4999** the local memory address in the Outbound Post Head Pointer Register. The processor must then 5000** increment the Outbound Post Head Pointer Register. 5001** ================================================== 5002** Outbound Free Queue 5003** ----------------------- 5004** The Outbound Free Queue holds free messages placed there by other processors for the Intel 5005** XScale core to use. This queue is read from the queue tail by the Intel XScale core. It is 5006** written to the queue head by external PCI agents. The tail pointer is maintained by the Intel 5007** XScale core. The head pointer is maintained by the MU hardware. 5008** For a PCI write transaction that accesses the Outbound Queue Port, the MU writes the data to the 5009** local memory address in the Outbound Free Head Pointer Register. When the data written to the 5010** Outbound Queue Port is written to local memory, the MU hardware increments the Outbound Free 5011** Head Pointer Register. 5012** When the head pointer and the tail pointer become equal and the queue is full, the MU may signal 5013** an interrupt to the Intel XScale core to register the queue full condition. This interrupt is 5014** recorded in the Inbound Interrupt Status Register. The interrupt is cleared when the Outbound Free 5015** Queue Full Interrupt bit is cleared and not by writing to the head or tail pointers. The interrupt can 5016** be masked by the Inbound Interrupt Mask Register. Software must be aware of the state of the 5017** Outbound Free Queue Interrupt Mask bit to guarantee that the full condition is recognized by the 5018** core processor. 5019** From the time that a PCI write transaction is received until the data is written in local memory and 5020** the Outbound Free Head Pointer Register is incremented, any PCI transaction that attempts to 5021** access the Outbound Free Queue Port is signalled a retry. 5022** The Intel XScale core may read messages from the Outbound Free Queue by reading the data 5023** from the local memory address in the Outbound Free Tail Pointer Register. The processor must 5024** then increment the Outbound Free Tail Pointer Register. When the Outbound Free Queue is full, 5025** the hardware must retry any PCI writes until a slot in the queue becomes available. 5026** 5027** ================================================================================== 5028** Circular Queue Summary 5029** ---------------------- 5030** ________________________________________________________________________________________________________________________________________________ 5031** | Queue Name | PCI Port |Generate PCI Interrupt |Generate Intel Xscale Core Interrupt|Head Pointer maintained by|Tail Pointer maintained by| 5032** |_____________|_______________|_______________________|____________________________________|__________________________|__________________________| 5033** |Inbound Post | Inbound Queue | | | | | 5034** | Queue | Port | NO | Yes, when queue is written | MU hardware | Intel XScale | 5035** |_____________|_______________|_______________________|____________________________________|__________________________|__________________________| 5036** |Inbound Free | Inbound Queue | | | | | 5037** | Queue | Port | NO | NO | Intel XScale | MU hardware | 5038** |_____________|_______________|_______________________|____________________________________|__________________________|__________________________| 5039** ================================================================================== 5040** Circular Queue Status Summary 5041** ---------------------- 5042** ____________________________________________________________________________________________________ 5043** | Queue Name | Queue Status | Head & Tail Pointer | Last Pointer Update | 5044** |_____________________|________________|_____________________|_______________________________________| 5045** | Inbound Post Queue | Empty | Equal | Tail pointer last updated by software | 5046** |_____________________|________________|_____________________|_______________________________________| 5047** | Inbound Free Queue | Empty | Equal | Head pointer last updated by hardware | 5048** |_____________________|________________|_____________________|_______________________________________| 5049************************************************************************** 5050*/ 5051 5052/* 5053************************************************************************** 5054** Index Registers 5055** ======================== 5056** . The Index Registers are a set of 1004 registers that when written by an external PCI agent can generate an interrupt to the Intel XScale core. 5057** These registers are for inbound messages only. 5058** The interrupt is recorded in the Inbound Interrupt Status Register. 5059** The storage for the Index Registers is allocated from the 80331 local memory. 5060** PCI write accesses to the Index Registers write the data to local memory. 5061** PCI read accesses to the Index Registers read the data from local memory. 5062** . The local memory used for the Index Registers ranges from Inbound ATU Translate Value Register + 050H 5063** to Inbound ATU Translate Value Register + FFFH. 5064** . The address of the first write access is stored in the Index Address Register. 5065** This register is written during the earliest write access and provides a means to determine which Index Register was written. 5066** Once updated by the MU, the Index Address Register is not updated until the Index Register 5067** Interrupt bit in the Inbound Interrupt Status Register is cleared. 5068** . When the interrupt is cleared, the Index Address Register is re-enabled and stores the address of the next Index Register write access. 5069** Writes by the Intel XScale core to the local memory used by the Index Registers 5070** does not cause an interrupt and does not update the Index Address Register. 5071** . The index registers can be accessed with Multi-DWORD reads and single QWORD aligned writes. 5072************************************************************************** 5073*/ 5074/* 5075************************************************************************** 5076** Messaging Unit Internal Bus Memory Map 5077** ======================================= 5078** Internal Bus Address___Register Description (Name)____________________|_PCI Configuration Space Register Number_ 5079** FFFF E300H reserved | 5080** .. .. | 5081** FFFF E30CH reserved | 5082** FFFF E310H Inbound Message Register 0 | Available through 5083** FFFF E314H Inbound Message Register 1 | ATU Inbound Translation Window 5084** FFFF E318H Outbound Message Register 0 | 5085** FFFF E31CH Outbound Message Register 1 | or 5086** FFFF E320H Inbound Doorbell Register | 5087** FFFF E324H Inbound Interrupt Status Register | must translate PCI address to 5088** FFFF E328H Inbound Interrupt Mask Register | the Intel Xscale Core 5089** FFFF E32CH Outbound Doorbell Register | Memory-Mapped Address 5090** FFFF E330H Outbound Interrupt Status Register | 5091** FFFF E334H Outbound Interrupt Mask Register | 5092** ______________________________________________________________________|________________________________________ 5093** FFFF E338H reserved | 5094** FFFF E33CH reserved | 5095** FFFF E340H reserved | 5096** FFFF E344H reserved | 5097** FFFF E348H reserved | 5098** FFFF E34CH reserved | 5099** FFFF E350H MU Configuration Register | 5100** FFFF E354H Queue Base Address Register | 5101** FFFF E358H reserved | 5102** FFFF E35CH reserved | must translate PCI address to 5103** FFFF E360H Inbound Free Head Pointer Register | the Intel Xscale Core 5104** FFFF E364H Inbound Free Tail Pointer Register | Memory-Mapped Address 5105** FFFF E368H Inbound Post Head pointer Register | 5106** FFFF E36CH Inbound Post Tail Pointer Register | 5107** FFFF E370H Outbound Free Head Pointer Register | 5108** FFFF E374H Outbound Free Tail Pointer Register | 5109** FFFF E378H Outbound Post Head pointer Register | 5110** FFFF E37CH Outbound Post Tail Pointer Register | 5111** FFFF E380H Index Address Register | 5112** FFFF E384H reserved | 5113** .. .. | 5114** FFFF E3FCH reserved | 5115** ______________________________________________________________________|_______________________________________ 5116************************************************************************** 5117*/ 5118/* 5119************************************************************************** 5120** MU Configuration Register - MUCR FFFF.E350H 5121** 5122** . The MU Configuration Register (MUCR) contains the Circular Queue Enable bit and the size of one Circular Queue. 5123** . The Circular Queue Enable bit enables or disables the Circular Queues. 5124** The Circular Queues are disabled at reset to allow the software to initialize the head 5125** and tail pointer registers before any PCI accesses to the Queue Ports. 5126** . Each Circular Queue may range from 4 K entries (16 Kbytes) to 64 K entries (256 Kbytes) and there are four Circular Queues. 5127** ------------------------------------------------------------------------ 5128** Bit Default Description 5129** 31:06 000000H 00 2 Reserved 5130** 05:01 00001 2 Circular Queue Size - This field determines the size of each Circular Queue. 5131** All four queues are the same size. 5132** �E 00001 2 - 4K Entries (16 Kbytes) 5133** �E 00010 2 - 8K Entries (32 Kbytes) 5134** �E 00100 2 - 16K Entries (64 Kbytes) 5135** �E 01000 2 - 32K Entries (128 Kbytes) 5136** �E 10000 2 - 64K Entries (256 Kbytes) 5137** 00 0 2 Circular Queue Enable - This bit enables or disables the Circular Queues. When clear the Circular 5138** Queues are disabled, however the MU accepts PCI accesses to the Circular Queue Ports but ignores 5139** the data for Writes and return FFFF.FFFFH for Reads. Interrupts are not generated to the core when 5140** disabled. When set, the Circular Queues are fully enabled. 5141************************************************************************** 5142*/ 5143#define ARCMSR_MU_CONFIGURATION_REG 0xFFFFE350 5144#define ARCMSR_MU_CIRCULAR_QUEUE_SIZE64K 0x0020 5145#define ARCMSR_MU_CIRCULAR_QUEUE_SIZE32K 0x0010 5146#define ARCMSR_MU_CIRCULAR_QUEUE_SIZE16K 0x0008 5147#define ARCMSR_MU_CIRCULAR_QUEUE_SIZE8K 0x0004 5148#define ARCMSR_MU_CIRCULAR_QUEUE_SIZE4K 0x0002 5149#define ARCMSR_MU_CIRCULAR_QUEUE_ENABLE 0x0001 /*0:disable 1:enable*/ 5150/* 5151************************************************************************** 5152** Queue Base Address Register - QBAR 5153** 5154** . The Queue Base Address Register (QBAR) contains the local memory address of the Circular Queues. 5155** The base address is required to be located on a 1 Mbyte address boundary. 5156** . All Circular Queue head and tail pointers are based on the QBAR. 5157** When the head and tail pointer registers are read, the Queue Base Address is returned in the upper 12 bits. 5158** Writing to the upper 12 bits of the head and tail pointer registers does not affect the Queue Base Address or Queue Base Address Register. 5159** Warning: 5160** The QBAR must designate a range allocated to the 80331 DDR SDRAM interface 5161** ------------------------------------------------------------------------ 5162** Bit Default Description 5163** 31:20 000H Queue Base Address - Local memory address of the circular queues. 5164** 19:00 00000H Reserved 5165************************************************************************** 5166*/ 5167#define ARCMSR_MU_QUEUE_BASE_ADDRESS_REG 0xFFFFE354 5168/* 5169************************************************************************** 5170** Inbound Free Head Pointer Register - IFHPR 5171** 5172** . The Inbound Free Head Pointer Register (IFHPR) contains the local memory offset from 5173** the Queue Base Address of the head pointer for the Inbound Free Queue. 5174** The Head Pointer must be aligned on a DWORD address boundary. 5175** When read, the Queue Base Address is provided in the upper 12 bits of the register. 5176** Writes to the upper 12 bits of the register are ignored. 5177** This register is maintained by software. 5178** ------------------------------------------------------------------------ 5179** Bit Default Description 5180** 31:20 000H Queue Base Address - Local memory address of the circular queues. 5181** 19:02 0000H 00 2 Inbound Free Head Pointer - Local memory offset of the head pointer for the Inbound Free Queue. 5182** 01:00 00 2 Reserved 5183************************************************************************** 5184*/ 5185#define ARCMSR_MU_INBOUND_FREE_HEAD_PTR_REG 0xFFFFE360 5186/* 5187************************************************************************** 5188** Inbound Free Tail Pointer Register - IFTPR 5189** 5190** . The Inbound Free Tail Pointer Register (IFTPR) contains the local memory offset from the Queue 5191** Base Address of the tail pointer for the Inbound Free Queue. The Tail Pointer must be aligned on a 5192** DWORD address boundary. When read, the Queue Base Address is provided in the upper 12 bits 5193** of the register. Writes to the upper 12 bits of the register are ignored. 5194** ------------------------------------------------------------------------ 5195** Bit Default Description 5196** 31:20 000H Queue Base Address - Local memory address of the circular queues. 5197** 19:02 0000H 00 2 Inbound Free Tail Pointer - Local memory offset of the tail pointer for the Inbound Free Queue. 5198** 01:00 00 2 Reserved 5199************************************************************************** 5200*/ 5201#define ARCMSR_MU_INBOUND_FREE_TAIL_PTR_REG 0xFFFFE364 5202/* 5203************************************************************************** 5204** Inbound Post Head Pointer Register - IPHPR 5205** 5206** . The Inbound Post Head Pointer Register (IPHPR) contains the local memory offset from the Queue 5207** Base Address of the head pointer for the Inbound Post Queue. The Head Pointer must be aligned on 5208** a DWORD address boundary. When read, the Queue Base Address is provided in the upper 12 bits 5209** of the register. Writes to the upper 12 bits of the register are ignored. 5210** ------------------------------------------------------------------------ 5211** Bit Default Description 5212** 31:20 000H Queue Base Address - Local memory address of the circular queues. 5213** 19:02 0000H 00 2 Inbound Post Head Pointer - Local memory offset of the head pointer for the Inbound Post Queue. 5214** 01:00 00 2 Reserved 5215************************************************************************** 5216*/ 5217#define ARCMSR_MU_INBOUND_POST_HEAD_PTR_REG 0xFFFFE368 5218/* 5219************************************************************************** 5220** Inbound Post Tail Pointer Register - IPTPR 5221** 5222** . The Inbound Post Tail Pointer Register (IPTPR) contains the local memory offset from the Queue 5223** Base Address of the tail pointer for the Inbound Post Queue. The Tail Pointer must be aligned on a 5224** DWORD address boundary. When read, the Queue Base Address is provided in the upper 12 bits 5225** of the register. Writes to the upper 12 bits of the register are ignored. 5226** ------------------------------------------------------------------------ 5227** Bit Default Description 5228** 31:20 000H Queue Base Address - Local memory address of the circular queues. 5229** 19:02 0000H 00 2 Inbound Post Tail Pointer - Local memory offset of the tail pointer for the Inbound Post Queue. 5230** 01:00 00 2 Reserved 5231************************************************************************** 5232*/ 5233#define ARCMSR_MU_INBOUND_POST_TAIL_PTR_REG 0xFFFFE36C 5234/* 5235************************************************************************** 5236** Index Address Register - IAR 5237** 5238** . The Index Address Register (IAR) contains the offset of the least recently accessed Index Register. 5239** It is written by the MU when the Index Registers are written by a PCI agent. 5240** The register is not updated until the Index Interrupt bit in the Inbound Interrupt Status Register is cleared. 5241** . The local memory address of the Index Register least recently accessed is computed 5242** by adding the Index Address Register to the Inbound ATU Translate Value Register. 5243** ------------------------------------------------------------------------ 5244** Bit Default Description 5245** 31:12 000000H Reserved 5246** 11:02 00H 00 2 Index Address - is the local memory offset of the Index Register written (050H to FFCH) 5247** 01:00 00 2 Reserved 5248************************************************************************** 5249*/ 5250#define ARCMSR_MU_LOCAL_MEMORY_INDEX_REG 0xFFFFE380 /*1004 dwords 0x0050....0x0FFC, 4016 bytes 0x0050...0x0FFF*/ 5251/* 5252********************************************************************************************************** 5253** RS-232 Interface for Areca Raid Controller 5254** The low level command interface is exclusive with VT100 terminal 5255** -------------------------------------------------------------------- 5256** 1. Sequence of command execution 5257** -------------------------------------------------------------------- 5258** (A) Header : 3 bytes sequence (0x5E, 0x01, 0x61) 5259** (B) Command block : variable length of data including length, command code, data and checksum byte 5260** (C) Return data : variable length of data 5261** -------------------------------------------------------------------- 5262** 2. Command block 5263** -------------------------------------------------------------------- 5264** (A) 1st byte : command block length (low byte) 5265** (B) 2nd byte : command block length (high byte) 5266** note ..command block length shouldn't > 2040 bytes, length excludes these two bytes 5267** (C) 3rd byte : command code 5268** (D) 4th and following bytes : variable length data bytes depends on command code 5269** (E) last byte : checksum byte (sum of 1st byte until last data byte) 5270** -------------------------------------------------------------------- 5271** 3. Command code and associated data 5272** -------------------------------------------------------------------- 5273** The following are command code defined in raid controller Command code 0x10--0x1? are used for system level management, 5274** no password checking is needed and should be implemented in separate well controlled utility and not for end user access. 5275** Command code 0x20--0x?? always check the password, password must be entered to enable these command. 5276** enum 5277** { 5278** GUI_SET_SERIAL=0x10, 5279** GUI_SET_VENDOR, 5280** GUI_SET_MODEL, 5281** GUI_IDENTIFY, 5282** GUI_CHECK_PASSWORD, 5283** GUI_LOGOUT, 5284** GUI_HTTP, 5285** GUI_SET_ETHERNET_ADDR, 5286** GUI_SET_LOGO, 5287** GUI_POLL_EVENT, 5288** GUI_GET_EVENT, 5289** GUI_GET_HW_MONITOR, 5290** 5291** // GUI_QUICK_CREATE=0x20, (function removed) 5292** GUI_GET_INFO_R=0x20, 5293** GUI_GET_INFO_V, 5294** GUI_GET_INFO_P, 5295** GUI_GET_INFO_S, 5296** GUI_CLEAR_EVENT, 5297** 5298** GUI_MUTE_BEEPER=0x30, 5299** GUI_BEEPER_SETTING, 5300** GUI_SET_PASSWORD, 5301** GUI_HOST_INTERFACE_MODE, 5302** GUI_REBUILD_PRIORITY, 5303** GUI_MAX_ATA_MODE, 5304** GUI_RESET_CONTROLLER, 5305** GUI_COM_PORT_SETTING, 5306** GUI_NO_OPERATION, 5307** GUI_DHCP_IP, 5308** 5309** GUI_CREATE_PASS_THROUGH=0x40, 5310** GUI_MODIFY_PASS_THROUGH, 5311** GUI_DELETE_PASS_THROUGH, 5312** GUI_IDENTIFY_DEVICE, 5313** 5314** GUI_CREATE_RAIDSET=0x50, 5315** GUI_DELETE_RAIDSET, 5316** GUI_EXPAND_RAIDSET, 5317** GUI_ACTIVATE_RAIDSET, 5318** GUI_CREATE_HOT_SPARE, 5319** GUI_DELETE_HOT_SPARE, 5320** 5321** GUI_CREATE_VOLUME=0x60, 5322** GUI_MODIFY_VOLUME, 5323** GUI_DELETE_VOLUME, 5324** GUI_START_CHECK_VOLUME, 5325** GUI_STOP_CHECK_VOLUME 5326** }; 5327** 5328** Command description : 5329** 5330** GUI_SET_SERIAL : Set the controller serial# 5331** byte 0,1 : length 5332** byte 2 : command code 0x10 5333** byte 3 : password length (should be 0x0f) 5334** byte 4-0x13 : should be "ArEcATecHnoLogY" 5335** byte 0x14--0x23 : Serial number string (must be 16 bytes) 5336** GUI_SET_VENDOR : Set vendor string for the controller 5337** byte 0,1 : length 5338** byte 2 : command code 0x11 5339** byte 3 : password length (should be 0x08) 5340** byte 4-0x13 : should be "ArEcAvAr" 5341** byte 0x14--0x3B : vendor string (must be 40 bytes) 5342** GUI_SET_MODEL : Set the model name of the controller 5343** byte 0,1 : length 5344** byte 2 : command code 0x12 5345** byte 3 : password length (should be 0x08) 5346** byte 4-0x13 : should be "ArEcAvAr" 5347** byte 0x14--0x1B : model string (must be 8 bytes) 5348** GUI_IDENTIFY : Identify device 5349** byte 0,1 : length 5350** byte 2 : command code 0x13 5351** return "Areca RAID Subsystem " 5352** GUI_CHECK_PASSWORD : Verify password 5353** byte 0,1 : length 5354** byte 2 : command code 0x14 5355** byte 3 : password length 5356** byte 4-0x?? : user password to be checked 5357** GUI_LOGOUT : Logout GUI (force password checking on next command) 5358** byte 0,1 : length 5359** byte 2 : command code 0x15 5360** GUI_HTTP : HTTP interface (reserved for Http proxy service)(0x16) 5361** 5362** GUI_SET_ETHERNET_ADDR : Set the ethernet MAC address 5363** byte 0,1 : length 5364** byte 2 : command code 0x17 5365** byte 3 : password length (should be 0x08) 5366** byte 4-0x13 : should be "ArEcAvAr" 5367** byte 0x14--0x19 : Ethernet MAC address (must be 6 bytes) 5368** GUI_SET_LOGO : Set logo in HTTP 5369** byte 0,1 : length 5370** byte 2 : command code 0x18 5371** byte 3 : Page# (0/1/2/3) (0xff --> clear OEM logo) 5372** byte 4/5/6/7 : 0x55/0xaa/0xa5/0x5a 5373** byte 8 : TITLE.JPG data (each page must be 2000 bytes) 5374** note .... page0 1st 2 byte must be actual length of the JPG file 5375** GUI_POLL_EVENT : Poll If Event Log Changed 5376** byte 0,1 : length 5377** byte 2 : command code 0x19 5378** GUI_GET_EVENT : Read Event 5379** byte 0,1 : length 5380** byte 2 : command code 0x1a 5381** byte 3 : Event Page (0:1st page/1/2/3:last page) 5382** GUI_GET_HW_MONITOR : Get HW monitor data 5383** byte 0,1 : length 5384** byte 2 : command code 0x1b 5385** byte 3 : # of FANs(example 2) 5386** byte 4 : # of Voltage sensor(example 3) 5387** byte 5 : # of temperature sensor(example 2) 5388** byte 6 : # of power 5389** byte 7/8 : Fan#0 (RPM) 5390** byte 9/10 : Fan#1 5391** byte 11/12 : Voltage#0 original value in *1000 5392** byte 13/14 : Voltage#0 value 5393** byte 15/16 : Voltage#1 org 5394** byte 17/18 : Voltage#1 5395** byte 19/20 : Voltage#2 org 5396** byte 21/22 : Voltage#2 5397** byte 23 : Temp#0 5398** byte 24 : Temp#1 5399** byte 25 : Power indicator (bit0 : power#0, bit1 : power#1) 5400** byte 26 : UPS indicator 5401** GUI_QUICK_CREATE : Quick create raid/volume set 5402** byte 0,1 : length 5403** byte 2 : command code 0x20 5404** byte 3/4/5/6 : raw capacity 5405** byte 7 : raid level 5406** byte 8 : stripe size 5407** byte 9 : spare 5408** byte 10/11/12/13: device mask (the devices to create raid/volume) 5409** This function is removed, application like to implement quick create function 5410** need to use GUI_CREATE_RAIDSET and GUI_CREATE_VOLUMESET function. 5411** GUI_GET_INFO_R : Get Raid Set Information 5412** byte 0,1 : length 5413** byte 2 : command code 0x20 5414** byte 3 : raidset# 5415** 5416** typedef struct sGUI_RAIDSET 5417** { 5418** BYTE grsRaidSetName[16]; 5419** DWORD grsCapacity; 5420** DWORD grsCapacityX; 5421** DWORD grsFailMask; 5422** BYTE grsDevArray[32]; 5423** BYTE grsMemberDevices; 5424** BYTE grsNewMemberDevices; 5425** BYTE grsRaidState; 5426** BYTE grsVolumes; 5427** BYTE grsVolumeList[16]; 5428** BYTE grsRes1; 5429** BYTE grsRes2; 5430** BYTE grsRes3; 5431** BYTE grsFreeSegments; 5432** DWORD grsRawStripes[8]; 5433** DWORD grsRes4; 5434** DWORD grsRes5; // Total to 128 bytes 5435** DWORD grsRes6; // Total to 128 bytes 5436** } sGUI_RAIDSET, *pGUI_RAIDSET; 5437** GUI_GET_INFO_V : Get Volume Set Information 5438** byte 0,1 : length 5439** byte 2 : command code 0x21 5440** byte 3 : volumeset# 5441** 5442** typedef struct sGUI_VOLUMESET 5443** { 5444** BYTE gvsVolumeName[16]; // 16 5445** DWORD gvsCapacity; 5446** DWORD gvsCapacityX; 5447** DWORD gvsFailMask; 5448** DWORD gvsStripeSize; 5449** DWORD gvsNewFailMask; 5450** DWORD gvsNewStripeSize; 5451** DWORD gvsVolumeStatus; 5452** DWORD gvsProgress; // 32 5453** sSCSI_ATTR gvsScsi; 5454** BYTE gvsMemberDisks; 5455** BYTE gvsRaidLevel; // 8 5456** 5457** BYTE gvsNewMemberDisks; 5458** BYTE gvsNewRaidLevel; 5459** BYTE gvsRaidSetNumber; 5460** BYTE gvsRes0; // 4 5461** BYTE gvsRes1[4]; // 64 bytes 5462** } sGUI_VOLUMESET, *pGUI_VOLUMESET; 5463** 5464** GUI_GET_INFO_P : Get Physical Drive Information 5465** byte 0,1 : length 5466** byte 2 : command code 0x22 5467** byte 3 : drive # (from 0 to max-channels - 1) 5468** 5469** typedef struct sGUI_PHY_DRV 5470** { 5471** BYTE gpdModelName[40]; 5472** BYTE gpdSerialNumber[20]; 5473** BYTE gpdFirmRev[8]; 5474** DWORD gpdCapacity; 5475** DWORD gpdCapacityX; // Reserved for expansion 5476** BYTE gpdDeviceState; 5477** BYTE gpdPioMode; 5478** BYTE gpdCurrentUdmaMode; 5479** BYTE gpdUdmaMode; 5480** BYTE gpdDriveSelect; 5481** BYTE gpdRaidNumber; // 0xff if not belongs to a raid set 5482** sSCSI_ATTR gpdScsi; 5483** BYTE gpdReserved[40]; // Total to 128 bytes 5484** } sGUI_PHY_DRV, *pGUI_PHY_DRV; 5485** 5486** GUI_GET_INFO_S : Get System Information 5487** byte 0,1 : length 5488** byte 2 : command code 0x23 5489** 5490** typedef struct sCOM_ATTR 5491** { 5492** BYTE comBaudRate; 5493** BYTE comDataBits; 5494** BYTE comStopBits; 5495** BYTE comParity; 5496** BYTE comFlowControl; 5497** } sCOM_ATTR, *pCOM_ATTR; 5498** 5499** typedef struct sSYSTEM_INFO 5500** { 5501** BYTE gsiVendorName[40]; 5502** BYTE gsiSerialNumber[16]; 5503** BYTE gsiFirmVersion[16]; 5504** BYTE gsiBootVersion[16]; 5505** BYTE gsiMbVersion[16]; 5506** BYTE gsiModelName[8]; 5507** BYTE gsiLocalIp[4]; 5508** BYTE gsiCurrentIp[4]; 5509** DWORD gsiTimeTick; 5510** DWORD gsiCpuSpeed; 5511** DWORD gsiICache; 5512** DWORD gsiDCache; 5513** DWORD gsiScache; 5514** DWORD gsiMemorySize; 5515** DWORD gsiMemorySpeed; 5516** DWORD gsiEvents; 5517** BYTE gsiMacAddress[6]; 5518** BYTE gsiDhcp; 5519** BYTE gsiBeeper; 5520** BYTE gsiChannelUsage; 5521** BYTE gsiMaxAtaMode; 5522** BYTE gsiSdramEcc; // 1:if ECC enabled 5523** BYTE gsiRebuildPriority; 5524** sCOM_ATTR gsiComA; // 5 bytes 5525** sCOM_ATTR gsiComB; // 5 bytes 5526** BYTE gsiIdeChannels; 5527** BYTE gsiScsiHostChannels; 5528** BYTE gsiIdeHostChannels; 5529** BYTE gsiMaxVolumeSet; 5530** BYTE gsiMaxRaidSet; 5531** BYTE gsiEtherPort; // 1:if ether net port supported 5532** BYTE gsiRaid6Engine; // 1:Raid6 engine supported 5533** BYTE gsiRes[75]; 5534** } sSYSTEM_INFO, *pSYSTEM_INFO; 5535** 5536** GUI_CLEAR_EVENT : Clear System Event 5537** byte 0,1 : length 5538** byte 2 : command code 0x24 5539** 5540** GUI_MUTE_BEEPER : Mute current beeper 5541** byte 0,1 : length 5542** byte 2 : command code 0x30 5543** 5544** GUI_BEEPER_SETTING : Disable beeper 5545** byte 0,1 : length 5546** byte 2 : command code 0x31 5547** byte 3 : 0->disable, 1->enable 5548** 5549** GUI_SET_PASSWORD : Change password 5550** byte 0,1 : length 5551** byte 2 : command code 0x32 5552** byte 3 : pass word length ( must <= 15 ) 5553** byte 4 : password (must be alpha-numerical) 5554** 5555** GUI_HOST_INTERFACE_MODE : Set host interface mode 5556** byte 0,1 : length 5557** byte 2 : command code 0x33 5558** byte 3 : 0->Independent, 1->cluster 5559** 5560** GUI_REBUILD_PRIORITY : Set rebuild priority 5561** byte 0,1 : length 5562** byte 2 : command code 0x34 5563** byte 3 : 0/1/2/3 (low->high) 5564** 5565** GUI_MAX_ATA_MODE : Set maximum ATA mode to be used 5566** byte 0,1 : length 5567** byte 2 : command code 0x35 5568** byte 3 : 0/1/2/3 (133/100/66/33) 5569** 5570** GUI_RESET_CONTROLLER : Reset Controller 5571** byte 0,1 : length 5572** byte 2 : command code 0x36 5573** *Response with VT100 screen (discard it) 5574** 5575** GUI_COM_PORT_SETTING : COM port setting 5576** byte 0,1 : length 5577** byte 2 : command code 0x37 5578** byte 3 : 0->COMA (term port), 1->COMB (debug port) 5579** byte 4 : 0/1/2/3/4/5/6/7 (1200/2400/4800/9600/19200/38400/57600/115200) 5580** byte 5 : data bit (0:7 bit, 1:8 bit : must be 8 bit) 5581** byte 6 : stop bit (0:1, 1:2 stop bits) 5582** byte 7 : parity (0:none, 1:off, 2:even) 5583** byte 8 : flow control (0:none, 1:xon/xoff, 2:hardware => must use none) 5584** 5585** GUI_NO_OPERATION : No operation 5586** byte 0,1 : length 5587** byte 2 : command code 0x38 5588** 5589** GUI_DHCP_IP : Set DHCP option and local IP address 5590** byte 0,1 : length 5591** byte 2 : command code 0x39 5592** byte 3 : 0:dhcp disabled, 1:dhcp enabled 5593** byte 4/5/6/7 : IP address 5594** 5595** GUI_CREATE_PASS_THROUGH : Create pass through disk 5596** byte 0,1 : length 5597** byte 2 : command code 0x40 5598** byte 3 : device # 5599** byte 4 : scsi channel (0/1) 5600** byte 5 : scsi id (0-->15) 5601** byte 6 : scsi lun (0-->7) 5602** byte 7 : tagged queue (1 : enabled) 5603** byte 8 : cache mode (1 : enabled) 5604** byte 9 : max speed (0/1/2/3/4, async/20/40/80/160 for scsi) 5605** (0/1/2/3/4, 33/66/100/133/150 for ide ) 5606** 5607** GUI_MODIFY_PASS_THROUGH : Modify pass through disk 5608** byte 0,1 : length 5609** byte 2 : command code 0x41 5610** byte 3 : device # 5611** byte 4 : scsi channel (0/1) 5612** byte 5 : scsi id (0-->15) 5613** byte 6 : scsi lun (0-->7) 5614** byte 7 : tagged queue (1 : enabled) 5615** byte 8 : cache mode (1 : enabled) 5616** byte 9 : max speed (0/1/2/3/4, async/20/40/80/160 for scsi) 5617** (0/1/2/3/4, 33/66/100/133/150 for ide ) 5618** 5619** GUI_DELETE_PASS_THROUGH : Delete pass through disk 5620** byte 0,1 : length 5621** byte 2 : command code 0x42 5622** byte 3 : device# to be deleted 5623** 5624** GUI_IDENTIFY_DEVICE : Identify Device 5625** byte 0,1 : length 5626** byte 2 : command code 0x43 5627** byte 3 : Flash Method(0:flash selected, 1:flash not selected) 5628** byte 4/5/6/7 : IDE device mask to be flashed 5629** note .... no response data available 5630** 5631** GUI_CREATE_RAIDSET : Create Raid Set 5632** byte 0,1 : length 5633** byte 2 : command code 0x50 5634** byte 3/4/5/6 : device mask 5635** byte 7-22 : raidset name (if byte 7 == 0:use default) 5636** 5637** GUI_DELETE_RAIDSET : Delete Raid Set 5638** byte 0,1 : length 5639** byte 2 : command code 0x51 5640** byte 3 : raidset# 5641** 5642** GUI_EXPAND_RAIDSET : Expand Raid Set 5643** byte 0,1 : length 5644** byte 2 : command code 0x52 5645** byte 3 : raidset# 5646** byte 4/5/6/7 : device mask for expansion 5647** byte 8/9/10 : (8:0 no change, 1 change, 0xff:terminate, 9:new raid level,10:new stripe size 0/1/2/3/4/5->4/8/16/32/64/128K ) 5648** byte 11/12/13 : repeat for each volume in the raidset .... 5649** 5650** GUI_ACTIVATE_RAIDSET : Activate incomplete raid set 5651** byte 0,1 : length 5652** byte 2 : command code 0x53 5653** byte 3 : raidset# 5654** 5655** GUI_CREATE_HOT_SPARE : Create hot spare disk 5656** byte 0,1 : length 5657** byte 2 : command code 0x54 5658** byte 3/4/5/6 : device mask for hot spare creation 5659** 5660** GUI_DELETE_HOT_SPARE : Delete hot spare disk 5661** byte 0,1 : length 5662** byte 2 : command code 0x55 5663** byte 3/4/5/6 : device mask for hot spare deletion 5664** 5665** GUI_CREATE_VOLUME : Create volume set 5666** byte 0,1 : length 5667** byte 2 : command code 0x60 5668** byte 3 : raidset# 5669** byte 4-19 : volume set name (if byte4 == 0, use default) 5670** byte 20-27 : volume capacity (blocks) 5671** byte 28 : raid level 5672** byte 29 : stripe size (0/1/2/3/4/5->4/8/16/32/64/128K) 5673** byte 30 : channel 5674** byte 31 : ID 5675** byte 32 : LUN 5676** byte 33 : 1 enable tag 5677** byte 34 : 1 enable cache 5678** byte 35 : speed (0/1/2/3/4->async/20/40/80/160 for scsi) 5679** (0/1/2/3/4->33/66/100/133/150 for IDE ) 5680** byte 36 : 1 to select quick init 5681** 5682** GUI_MODIFY_VOLUME : Modify volume Set 5683** byte 0,1 : length 5684** byte 2 : command code 0x61 5685** byte 3 : volumeset# 5686** byte 4-19 : new volume set name (if byte4 == 0, not change) 5687** byte 20-27 : new volume capacity (reserved) 5688** byte 28 : new raid level 5689** byte 29 : new stripe size (0/1/2/3/4/5->4/8/16/32/64/128K) 5690** byte 30 : new channel 5691** byte 31 : new ID 5692** byte 32 : new LUN 5693** byte 33 : 1 enable tag 5694** byte 34 : 1 enable cache 5695** byte 35 : speed (0/1/2/3/4->async/20/40/80/160 for scsi) 5696** (0/1/2/3/4->33/66/100/133/150 for IDE ) 5697** 5698** GUI_DELETE_VOLUME : Delete volume set 5699** byte 0,1 : length 5700** byte 2 : command code 0x62 5701** byte 3 : volumeset# 5702** 5703** GUI_START_CHECK_VOLUME : Start volume consistency check 5704** byte 0,1 : length 5705** byte 2 : command code 0x63 5706** byte 3 : volumeset# 5707** 5708** GUI_STOP_CHECK_VOLUME : Stop volume consistency check 5709** byte 0,1 : length 5710** byte 2 : command code 0x64 5711** --------------------------------------------------------------------- 5712** 4. Returned data 5713** --------------------------------------------------------------------- 5714** (A) Header : 3 bytes sequence (0x5E, 0x01, 0x61) 5715** (B) Length : 2 bytes (low byte 1st, excludes length and checksum byte) 5716** (C) status or data : 5717** <1> If length == 1 ==> 1 byte status code 5718** #define GUI_OK 0x41 5719** #define GUI_RAIDSET_NOT_NORMAL 0x42 5720** #define GUI_VOLUMESET_NOT_NORMAL 0x43 5721** #define GUI_NO_RAIDSET 0x44 5722** #define GUI_NO_VOLUMESET 0x45 5723** #define GUI_NO_PHYSICAL_DRIVE 0x46 5724** #define GUI_PARAMETER_ERROR 0x47 5725** #define GUI_UNSUPPORTED_COMMAND 0x48 5726** #define GUI_DISK_CONFIG_CHANGED 0x49 5727** #define GUI_INVALID_PASSWORD 0x4a 5728** #define GUI_NO_DISK_SPACE 0x4b 5729** #define GUI_CHECKSUM_ERROR 0x4c 5730** #define GUI_PASSWORD_REQUIRED 0x4d 5731** <2> If length > 1 ==> data block returned from controller and the contents depends on the command code 5732** (E) Checksum : checksum of length and status or data byte 5733************************************************************************** 5734*/ 5735