All rights reserved.
This code is derived from software contributed to Berkeley by
the Systems Programming Group of the University of Utah Computer
Science Department.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software
must display the following acknowledgement:
This product includes software developed by the University of
California, Berkeley and its contributors.
4. Neither the name of the University nor the names of its contributors
may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
from: @(#)dca.4 5.2 (Berkeley) 3/27/91
from: com.4,v 1.1 1993/08/06 11:19:07 cgd Exp
$Id: sio.4,v 1.13 1994/06/15 23:28:07 jkh Exp $
.Dd June 3, 1994 .Dt SIO 4 i386 .Os FreeBSD .Sh NAME .Nm sio .Nd fast interrupt driven asynchronous serial communications interface .Sh SYNOPSIS For standard ports: .Cd "device sio0 at isa? port" "IO_COM1" tty irq 4 vector siointr .Cd "device sio1 at isa? port" "IO_COM2" tty irq 3 vector siointr .Cd "device sio2 at isa? port" "IO_COM3" tty irq 5 vector siointr .Cd "device sio3 at isa? port" "IO_COM4" tty irq 9 vector siointr For AST compatible multiport cards with 4 ports: .Cd "options" "COM_MULTIPORT" .Cd "device sio4 at isa? port 0x2a0 tty flags 0x701" .Cd "device sio5 at isa? port 0x2a8 tty flags 0x701" .Cd "device sio6 at isa? port 0x2b0 tty flags 0x701" .Cd "device sio7 at isa? port 0x2b8 tty flags 0x701 irq 12 vector siointr" For Boca Board compatible multiport cards with 8 ports: .Cd "options" "COM_MULTIPORT" .Cd "device sio4 at isa? port 0x100 tty flags 0xb05" .Cd "..." .Cd "device sio11 at isa? port 0x138 tty flags 0xb05 irq 12 vector siointr" Meaning of flags:
0x0001 shared IRQs
0x0002 disable FIFO
0x0004 no AST/4 compatible IRQ control register
0x0080 enable diagnostics in probe
0x??00 minor number of master port Minor numbering:
0bOLIMMMMM
callOut
Lock
Initial
MMMMMMinor .Sh DESCRIPTION The .Nm sio driver provides support for NS8250-, NS16450-, NS16550 and NS16550A-based .Tn EIA .Tn RS-232C
f ( Tn CCITT .Tn V.24 ) communications interfaces. The NS8250 and NS16450 have single character buffers, the NS16550A has 16 character FIFO input and output buffers.
p Input and output for each line may set to one of following baud rates; 50, 75, 110, 134.5, 150, 300, 600, 1200, 1800, 2400, 4800, 9600, 19200, 38400, 57600, or 115200. Your hardware may limit your baud rate choices.
p The driver supports `multiport' cards. Multiport cards are those that have one or more groups of ports that share an Interrupt Request (IRQ) line per group. Shared IRQs on different cards are not supported. Frequently 4 ports share 1 IRQ; some 8 port cards have 2 groups of 4 ports, thus using 2 IRQs. Some cards allow the first 2 serial ports to have seperate IRQs per port (as per DOS PC standard). Some cards have an IRQ control register for each group. Some cards require special initialization related to such registers. Only AST/4 compatible IRQ control registers are supported. Some cards have an IRQ status register for each group. The driver does not require or use such registers yet. To work, the control and status registers for a group, if any, must be mapped to the scratch register (register 7) of a port in the group. Such a port is called a .Nm master port. The .Nm flags keyword may be used on each .Nm device sio line in the kernel configuration file to silence the probe or to disable the FIFO on 16550A UARTs (see the synopsis). Disabling the FIFO should rarely be necessary since the driver automatically adjusts the receiver FIFO trigger level for low latency and high efficiency. The .Nm flags keyword .Nm must be used for all ports that are part of an IRQ sharing group. One bit specifies IRQ sharing; another bit specifies whether the port does .Nm not require AST/4 compatible initialization. The minor number of the device corresponding a master port for the group is encoded as a bitfield in the high byte. The same master port must be specified for all ports in a group. The .Nm irq and .Nm vector specifications must be given for master ports and for ports that are not part of an IRQ sharing group, and not for other ports.
p In the synopsis, .Nm flags 0x701 means that the 8th port (sio7) is the master port, and that the port is on a multiport card with shared IRQs and an AST/4 compatible IRQ control register. .Nm flags 0xb05 means that the 12th port (sio11) is the master port, and that the port is on a multiport card with shared IRQs and no special IRQ control register.
p Which port is the master port depends on the card type. Consult the hardware documentation of your card. Since IRQ status registers are never used, and IRQ control registers are only used for AST/4 compatible cards, and some cards map the control/status registers to all ports in a group, any port in a group will sometimes do for the master port. Choose a port containing an IRQ status register for forwards compatibility, and the highest possible port for consistency.
p Serial ports controlled by the .Nm sio driver can be used for both `callin' and `callout'. For each port there is a callin device and a callout device. The minor number of the callout device is 128 higher than that of the corresponding callin port. The callin device is general purpose. Processes opening it normally wait for carrier and for the callout device to become inactive. The callout device is used to steal the port from processes waiting for carrier on the callin device. Processes opening it do not wait for carrier and put any processes waiting for carrier on the callin device into a deeper sleep so that they do not conflict with the callout session. The callout device is abused for handling programs that are supposed to work on general ports and need to open the port without waiting but are too stupid to do so.
p The .Nm sio driver also supports an initial-state and a lock-state control device for each of the callin and the callout "data" devices. The minor number of the initial-state device is 32 higher than that of the corresponding data device. The minor number of the lock-state device is 64 higher than that of the corresponding data device. The termios settings of a data device are copied from those of the corresponding initial-state device on first opens and are not inherited from previous opens. Use .Xr stty 1 in the normal way on the initial-state devices to program initial termios states suitable for your setup. The lock termios state acts as flags to disable changing the termios state. E.g., to lock a flag variable such as CRTSCTS, use .Nm stty crtscts on the lock-state device. Speeds and special characters may be locked by setting the corresponding value in the lock-state device to any nonzero value. Correct programs talking to correctly wired external devices work with arbitrary initial states and almost no locking, but other setups may benefit from changing some of the default initial state and locking the state. E.g., CRTSCTS should be locked on for devices that support RTS/CTS handshaking at all times and off for devices that don't support it at all. CLOCAL should be locked on for devices that don't support carrier. HUPCL may be locked off if you don't want to hang up for reason. In general, very bad things happen if something is locked to the wrong state, and things should not be locked for devices that support more than one setting. The CLOCAL flag on callin ports should be locked off for logins to avoid certain security holes, but this needs to be done by getty if the callin port is used for anything else. .Sh FILES l -tag -width /dev/ttyi0? -compact t Pa /dev/ttyd? for callin and hardwired terminals ports t Pa /dev/ttyid? t Pa /dev/ttyld? corresponding callin initial-state and lock-state devices t Pa /dev/cuaa? for callout ports t Pa /dev/cuaia? t Pa /dev/cuala? corresponding callout initial-state and lock-state devices .El l -tag -width /etc/rc.serial -compact t Pa /etc/rc.serial examples of setting the initial-state and lock-state devices .El
p The devices numbers are made from the set [0-9a-v] so that more than 10 ports can be supported. .Sh DIAGNOSTICS l -diag t sio%d: silo overflow. Problem in the interrupt handler. .El l -diag t sio%d: interrupt-level buffer overflow. Problem in the bottom half of the driver. .El l -diag t sio%d: tty-level buffer overflow. Problem in the application. Input has arrived faster than the given module could process it and some has been lost. .El l -diag t sio%d: reduced fifo trigger level to %d. Attempting to avoid further silo overflows. .Sh SEE ALSO .Xr tty 4 , .Xr termios 4 , .Xr comcontrol 8 , .Xr stty 1 . .Sh HISTORY The .Nm driver is derived from the .Nm HP9000/300 .Nm dca driver and is d .Sh BUGS Data loss is not nearly as likely on busy systems as it is with the .Xr com 4 driver but it can still occur at very high baud rates on slow systems. The use of NS16550A's reduces system load and helps to avoid data loss.
p Stay away from plain NS16550's. These are early implementations of the chip with non-functional FIFO hardware.
p The constants which define the locations of the various serial ports are holdovers from .Nm DOS . As shown, hex addresses can be and for clarity probably should be used instead.
p Note that on the AST/4 the card's dipswitches should .Nm not be set to use interrupt sharing. AST/4-like interrupt sharing is only used when .Nm multiple AST/4 cards are installed in the same system. The sio driver does not support more than 1 AST/4 on one IRQ.
p Hardwired terminals should not have different device names.
p The examples in the synopsis are too vendor-specific.