All rights reserved.
This code is derived from software contributed to Berkeley by
the Systems Programming Group of the University of Utah Computer
Science Department.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. Neither the name of the University nor the names of its contributors
may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
from: @(#)dca.4 5.2 (Berkeley) 3/27/91
from: com.4,v 1.1 1993/08/06 11:19:07 cgd Exp
$FreeBSD: releng/11.0/share/man/man4/sio.4 263142 2014-03-14 03:07:51Z eadler $
.Dd August 30, 2006 .Dt SIO 4 .Os .Sh NAME .Nm sio .Nd "fast interrupt driven asynchronous serial communications interface" .Sh SYNOPSIS For standard ISA ports: d -ragged -offset indent -compact .Cd "device sio"
p In
a /boot/device.hints : .Cd hint.sio.0.at="isa" .Cd hint.sio.0.port="0x3f8" .Cd hint.sio.0.flags="0x10" .Cd hint.sio.0.irq="4" .Cd hint.sio.1.at="isa" .Cd hint.sio.1.port="0x2f8" .Cd hint.sio.1.flags="0x0" .Cd hint.sio.1.irq="3" .Ed
p For AST compatible multiport cards with 4 ports: d -ragged -offset indent -compact .Cd "options COM_MULTIPORT" .Cd "device sio"
p In
a /boot/device.hints : .Cd hint.sio.4.at="isa" .Cd hint.sio.4.port="0x2a0" .Cd hint.sio.4.flags="0x701" .Cd hint.sio.5.at="isa" .Cd hint.sio.5.port="0x2a8" .Cd hint.sio.5.flags="0x701" .Cd hint.sio.6.at="isa" .Cd hint.sio.6.port="0x2b0" .Cd hint.sio.6.flags="0x701" .Cd hint.sio.7.at="isa" .Cd hint.sio.7.port="0x2b8" .Cd hint.sio.7.flags="0x701" .Cd hint.sio.7.irq="12" .Ed
p For Boca Board compatible multiport cards with 8 ports: d -ragged -offset indent -compact .Cd "options COM_MULTIPORT" .Cd "device sio"
p In
a /boot/device.hints : .Cd hint.sio.4.at="isa" .Cd hint.sio.4.port="0x100" .Cd hint.sio.4.flags="0xb05" .Cd "..." .Cd hint.sio.11.at="isa" .Cd hint.sio.11.port="0x138" .Cd hint.sio.11.flags="0xb05" .Cd hint.sio.11.irq="12" .Ed
p For Netmos Nm9845 multiport cards with 6 ports: d -ragged -offset indent -compact .Cd "options COM_MULTIPORT" .Cd "device sio"
p In
a /boot/device.hints : .Cd hint.sio.4.at="isa" .Cd hint.sio.4.port="0xb000" .Cd hint.sio.4.flags="0x901" .Cd hint.sio.5.at="isa" .Cd hint.sio.5.port="0xb400" .Cd hint.sio.5.flags="0x901" .Cd hint.sio.6.at="isa" .Cd hint.sio.6.port="0xb800" .Cd hint.sio.6.flags="0x901" .Cd hint.sio.7.at="isa" .Cd hint.sio.7.port="0xbc00" .Cd hint.sio.7.flags="0x901" .Cd hint.sio.8.at="isa" .Cd hint.sio.8.port="0xc000" .Cd hint.sio.8.flags="0x901" .Cd hint.sio.9.at="isa" .Cd hint.sio.9.port="0xac00" .Cd hint.sio.9.flags="0x901" .Cd hint.sio.9.irq="12" .Ed
p For Hayes ESP cards: d -ragged -offset indent -compact .Cd "options COM_ESP" .Cd "device sio" .Cd "..." .Ed
p For single port PCI and PCCARD cards: d -ragged -offset indent -compact .Cd "device sio"
p No lines are required in
a /boot/device.hints for these cards. .Ed
p For dual port PCI cards that share an interrupt: d -ragged -offset indent -compact .Cd "device sio" .Cd "options COM_MULTIPORT"
p In
a /boot/device.hints : .Cd hint.sio.2.flags="0x201" .Cd hint.sio.3.flags="0x201" .Ed
p Meaning of .Ar flags : l -tag -offset indent -compact -width 0x000000 t 0x00001 shared IRQs t 0x00002 disable FIFO t 0x00004 no AST/4 compatible IRQ control register t 0x00008 recover sooner from lost output interrupts t 0x00010 device is potential system console t 0x00020 device is forced to become system console t 0x00040 device is reserved for low-level IO (e.g. for remote kernel debugging) t 0x00080 use this port for remote kernel debugging t 0x0 Ns Em ?? Ns 00 minor number of master port t 0x10000 PPS timestamping on CTS instead of DCD t 0x20000 device is assumed to use a 16650A-type (extended FIFO) chip .El .Sh DESCRIPTION The .Nm driver provides support for NS8250-, NS16450-, NS16550 and NS16550A-based .Tn EIA .Tn RS-232C
f ( Tn CCITT .Tn V.24 ) communications interfaces. The NS8250 and NS16450 have single character buffers, the NS16550A has 16 character FIFO input and output buffers.
p Input and output for each line may set to one of following baud rates; 50, 75, 110, 134.5, 150, 300, 600, 1200, 1800, 2400, 4800, 9600, 19200, 28800, 38400, 57600, or 115200. Your hardware may limit your baud rate choices.
p The driver supports `multiport' cards. Multiport cards are those that have one or more groups of ports that share an Interrupt Request (IRQ) line per group. Shared IRQs on different cards are not supported. Frequently 4 ports share 1 IRQ; some 8 port cards have 2 groups of 4 ports, thus using 2 IRQs. Some cards allow the first 2 serial ports to have separate IRQs per port (as per DOS PC standard).
p Some cards have an IRQ control register for each group. Some cards require special initialization related to such registers. Only AST/4 compatible IRQ control registers are supported. Some cards have an IRQ status register for each group. The driver does not require or use such registers yet. To work, the control and status registers for a group, if any, must be mapped to the scratch register (register 7) of a port in the group. Such a port is called a .Em master port.
p The driver supports controller based PCI modems. The 3Com FaxModem PCI and the Advantec 56k Voice Messaging PCI FaxModem are the only cards supported. WinModems, softmodems, hfc modems and any other modems that are not controller based are not supported.
p The .Em flags keyword may be used on each .Em device sio line in the kernel configuration file to disable the FIFO on 16550A UARTs (see the synopsis). Disabling the FIFO should rarely be necessary.
p The .Em flags keyword .Em must be used for all ports that are part of an IRQ sharing group. One bit specifies IRQ sharing; another bit specifies whether the port does .Em not require AST/4 compatible initialization. The minor number of the device corresponding a master port for the group is encoded as a bitfield in the high byte. The same master port must be specified for all ports in a group.
p The .Em irq specification must be given for master ports and for ports that are not part of an IRQ sharing group, and not for other ports.
p In the synopsis, .Em flags 0x701 means that the 8th port (sio7) is the master port, and that the port is on a multiport card with shared IRQs and an AST/4 compatible IRQ control register.
p .Em flags 0xb05 means that the 12th port (sio11) is the master port, and that the port is on a multiport card with shared IRQs and no special IRQ control register.
p Which port is the master port depends on the card type. Consult the hardware documentation of your card. Since IRQ status registers are never used, and IRQ control registers are only used for AST/4 compatible cards, and some cards map the control/status registers to all ports in a group, any port in a group will sometimes do for the master port. Choose a port containing an IRQ status register for forwards compatibility, and the highest possible port for consistency.
p Serial ports controlled by the .Nm driver can be used for both `callin' and `callout'. For each port there is a callin device and a callout device. The minor number of the callout device is 128 higher than that of the corresponding callin port. The callin device is general purpose. Processes opening it normally wait for carrier and for the callout device to become inactive. The callout device is used to steal the port from processes waiting for carrier on the callin device. Processes opening it do not wait for carrier and put any processes waiting for carrier on the callin device into a deeper sleep so that they do not conflict with the callout session. The callout device is abused for handling programs that are supposed to work on general ports and need to open the port without waiting but are too stupid to do so.
p The .Nm driver also supports an initial-state and a lock-state control device for each of the callin and the callout "data" devices. The termios settings of a data device are copied from those of the corresponding initial-state device on first opens and are not inherited from previous opens. Use .Xr stty 1 in the normal way on the initial-state devices to program initial termios states suitable for your setup.
p The lock termios state acts as flags to disable changing the termios state. E.g., to lock a flag variable such as CRTSCTS, use .Em stty crtscts on the lock-state device. Speeds and special characters may be locked by setting the corresponding value in the lock-state device to any nonzero value. E.g., to lock a speed to 115200, use .Dq Li stty 115200 on the initial-state device and .Dq Li stty 1 on the lock-state device.
p Correct programs talking to correctly wired external devices work with almost arbitrary initial states and almost no locking, but other setups may benefit from changing some of the default initial state and locking the state. In particular, the initial states for non (POSIX) standard flags should be set to suit the devices attached and may need to be locked to prevent buggy programs from changing them. E.g., CRTSCTS should be locked on for devices that support RTS/CTS handshaking at all times and off for devices that do not support it at all. CLOCAL should be locked on for devices that do not support carrier. HUPCL may be locked off if you do not want to hang up for some reason. In general, very bad things happen if something is locked to the wrong state, and things should not be locked for devices that support more than one setting. The CLOCAL flag on callin ports should be locked off for logins to avoid certain security holes, but this needs to be done by getty if the callin port is used for anything else. .Sh FILES l -tag -width /dev/ttyd?.init -compact t Pa /dev/ttyd? for callin ports t Pa /dev/ttyd?.init t Pa /dev/ttyd?.lock corresponding callin initial-state and lock-state devices
p t Pa /dev/cuad? for callout ports t Pa /dev/cuad?.init t Pa /dev/cuad?.lock corresponding callout initial-state and lock-state devices .El
p l -tag -width /etc/rc.d/serial -compact t Pa /etc/rc.d/serial examples of setting the initial-state and lock-state devices .El
p
The device numbers are made from the set [0-9a-v] so that more than
10 ports can be supported.
.Sh DIAGNOSTICS
l -diag t sio%d: silo overflow. Problem in the interrupt handler.
.El
l -diag t sio%d: interrupt-level buffer overflow. Problem in the bottom half of the driver.
.El
l -diag t sio%d: tty-level buffer overflow. Problem in the application.
Input has arrived faster than the given module could process it
and some has been lost.
.El
.Bl -diag
.It sio%d: reduced fifo trigger level to %d.
Attempting to avoid further silo overflows.
.El
.Sh SEE ALSO
.Xr stty 1 ,
.Xr termios 4 ,
.Xr tty 4 ,
.Xr comcontrol 8
.Sh HISTORY
The
.Nm
driver is derived from the
.Tn HP9000/300
.Xr dca 4
driver and is
d .Sh BUGS
Data loss may occur at very high baud rates on slow systems,
or with too many ports on any system,
or on heavily loaded systems when crtscts cannot be used.
The use of NS16550A's reduces system load and helps to avoid data loss.
p Stay away from plain NS16550's. These are early implementations of the chip with non-functional FIFO hardware.
p The constants which define the locations of the various serial ports are holdovers from .Tn DOS . As shown, hex addresses can be and for clarity probably should be used instead.
p Note that on the AST/4 the card's dipswitches should .Em not be set to use interrupt sharing. AST/4-like interrupt sharing is only used when .Em multiple AST/4 cards are installed in the same system. The .Nm driver does not support more than 1 AST/4 on one IRQ.
p The examples in the synopsis are too vendor-specific.