1# This file (and the kernel config file accompanying it) are not designed 2# to be used by themselves. Instead, users of this file should create a 3# kernel config file which includes this file (which gets the basic hints), 4# then override the default options (adding devices as needed) and adding 5# hints as needed (for example, the GPIO and LAN PHY.) 6 7# $FreeBSD$ 8 9hint.apb.0.at="nexus0" 10# The default APB is on IP6 (irq4); we need to add 11# the two new ones (IP2, IP3) to this and extend 12# the irq ranges appropriately. 13hint.apb.0.irq=4 14 15# uart0 16hint.uart.0.at="apb0" 17# NB: This isn't an ns8250 UART 18hint.uart.0.maddr=0x18020003 19hint.uart.0.msize=0x18 20hint.uart.0.irq=3 21 22# ehci - on IP3 23hint.ehci.0.at="nexus0" 24hint.ehci.0.maddr=0x1b000100 25hint.ehci.0.msize=0x00001000 26hint.ehci.0.irq=1 27 28hint.ehci.1.at="nexus0" 29hint.ehci.1.maddr=0x1b400100 30hint.ehci.1.msize=0x00001000 31hint.ehci.1.irq=1 32 33# PCIe 1: qca955x_int0 (IP2) 34 35# pci - XXX no maddr/msize, grr! 36hint.pcib.0.at="nexus0" 37hint.pcib.0.irq=0 38 39# PCIe 1: qca955x_int1 (IP3) 40hint.pcib.1.at="nexus0" 41hint.pcib.1.irq=1 42 43# IP4 44hint.arge.0.at="nexus0" 45hint.arge.0.maddr=0x19000000 46hint.arge.0.msize=0x1000 47hint.arge.0.irq=2 48 49# IP5 50hint.arge.1.at="nexus0" 51hint.arge.1.maddr=0x1a000000 52hint.arge.1.msize=0x1000 53hint.arge.1.irq=3 54 55# ath0 - connected via IP2 mux 56hint.ath.0.at="nexus0" 57hint.ath.0.maddr=0x18100000 58hint.ath.0.msize=0x20000 59hint.ath.0.irq=0 60hint.ath.0.vendor_id=0x168c 61hint.ath.0.device_id=0x0039 62# Set this to define where the ath calibration data 63# should be fetched from in physical memory. 64# hint.ath.0.eepromaddr=0x1fff1000 65 66# SPI flash 67hint.spi.0.at="nexus0" 68hint.spi.0.maddr=0x1f000000 69hint.spi.0.msize=0x10 70 71hint.mx25l.0.at="spibus0" 72hint.mx25l.0.cs=0 73 74# Watchdog 75hint.ar71xx_wdog.0.at="nexus0" 76 77# The GPIO function and pin mask is configured per-board 78hint.gpio.0.at="apb0" 79hint.gpio.0.maddr=0x18040000 80hint.gpio.0.msize=0x1000 81hint.gpio.0.irq=2 82